500 POW

ER CRADLE

Eastman

Keep

LooseObjec

ts

CAUTION

Away

From

Feed

Roll

EMERGENCYSTOP

REVE

RSE

OPEN

EDGE

MANUAL

OUT

MANUAL

FORW

ARD

CLOSE

LOAD

DIRECTIO

NAUTO

AUTO

IN43

21 0

5555555555555555555555555555555555555555555555555555555555555555555555555555555555

9

500#CAPACIT

Y

EASTMAN

THE EASTMAN

®

Power Tilt Cradle®

Please read completely before attempting to operate your new Power Tilt Cradle.

779 Washington St., Buffalo, N.Y. 14203-1396 U.S.A. • (716)856-2200 • Fax (716)856-1140 or (716)856-2068Manufacturers of Eastman Cloth Cutting and Cloth Spreading Machines

Website: www.EastmanCuts.com

WARNINGDrive Belts and Roller Tubes move at High Rate of Speed.Keep hands & loose objects

away from Drive Belts & Rollers.

Instruction Manual &Illustrated Parts List

Form CR-50-0437

*Mirror Image Shown

2

EASTMAN

Form CR-50-0437

®

IMPORTANTThe purchaser must instruct all operators on the proper use of this equipment. All standard industrial safety measures and equipment should be provided to protect the operator. Operators must be cautioned that improper or careless use of this equipment may cause personal injury. If you do not have qualified operators to instruct new persons, contact your EASTMAN sales representative or EASTMAN factory direct.

Electrical connections and servicing to this equipment should be made by a qualified electrician who is familiar with applicable codes and regulations. Disconnect this equipment from electrical power source before proceed-ing with any disassembly for adjustment or repair.

Your Eastman Power Tilt Cradle is designed to operate at a high rate of speed. All personnel should be instructed to wear safety glasses and stand well clear of the Power Tilt Cradle when in operation.

Table of Contents

Safety Information ....................................................................... 3Safety and Indemnification .......................................................... 3General Safety Precautions......................................................... 3INSTALLATION ........................................................................... 4OPERATION ................................................................................ 4OPERATING ADJUSTMENTS .................................................... 5SERVICE AND MAINTENANCE ................................................. 5THREADING DIAGRAM...............................................................5FAMILIARIZATION CONTROL BOX ........................................... 6Pictorial Index .............................................................................. 7Dancer Bar Assembly .................................................................. 8Tilt Cradle Assembly .................................................................. 10Edge Control Platform Assembly ............................................... 12Control Box Assembly ............................................................... 14Emergency Stop Box Assembly ................................................ 16Power Cradle Probe Assembly .................................................. 17Edge Upright Assembly ............................................................. 18Reverse Roll Assembly.............................................................. 19Power Cradle Uprights Assembly .............................................. 20Brake Assembly ......................................................................... 21Heavy Duty (#300) Expandabar ................................................ 22Heavy Duty (#500) Expandabar ................................................ 241 1/4" Dia. Solid Bar .................................................................. 25Tilt Cradle Electrical Schematic Blue Print No. 11-2952 ............ 26Tilt Cradle Electrical Diagram Blue Print No. 11-2953 ............... 27TECHNICAL DATA ................................................................... 28

3Form CR-50-0437

Safety Information Throughout this manual, safety information is presented by the use of the terms WARNING, CAUTION, and NOTE. These terms have the following meanings:

WARNING A warning contains critical information regarding

potential safety hazards that can occur during proper use or misuse of the machine. Failure to follow these procedures may result in serious personal injury to the user.

CAUTION A caution contains instructions for the use or main-

tenance of the machine. Failure to follow these procedures may result in damage to the machine. Supplementary information may be given in a Note.

ELECTRICAL HAZARD An electrical hazard calls attention to a proce-

dure, practice, or the like, which, if not correctly performed or adhered to, could result in personal injury. Do not proceed beyond an Electrical Haz-ard.

Safety and Indemnification During the life of the machine, the purchaser agrees to provide to all machine users (including its own employees and independent contractors) all relevant safety informa-tion, including warning labels and instruction manuals. The purchaser also agrees to maintain the safety features and working condition of the machine, and to adequately train all users in the safe use and maintenance of the machine. The purchaser agrees to defend, protect, indemnify, and hold Eastman Machine Company and its subsidiaries harmless from and against all claims, losses, expenses, damages, and liabilities to the extent that they have been caused by the purchaser’s failure to comply with the terms and instructions of this manual.

General Safety Precautions

WARNING • This machine is equipped with powerful cradle

roller tubes. Keep hands, arms, and hair away from the cradle area and drive system at all times. Safety gloves, glasses, and appropriate clothing may prevent serious personal injuries.

• Disconnect the power supply to the machine when it is not in use or during routine maintenance, in-cluding cleaning and lubrication.

• The purchaser must instruct all operators in the proper use of the machine according to the instruc-tions in this manual. This training must include instruction on the potential safety hazards arising from the use or misuse of the machine. In addi-tion to such training, the purchaser should provide written work instructions as necessary to ensure correct use of the machine for specific cutting and spreading applications.

• Do not modify this machine or disable safety features. Unauthorized modification may result in serious personal injuries to the user. Electrical connections to this machine must be made by a qualified electrician familiar with applicable codes and regulations.

• Safety labels must be kept clean and legible at all times. Call the Eastman Machine factory to order replacement labels.

4

EASTMAN

Form CR-50-0437

®

The Eastman Power Tilt Cradle is shipped partially disas-sembled with all the necessary parts for proper setup and operation. To get the best performance, familiarize yourself with all functions and adjustments of this equipment. Be-fore any operation can take place, it is important that you carefully read and follow the instructions in this manual in the same sequence in which they are presented.

INSTALLATION

Power Tilt Cradle InstallationThe Power Tilt Cradle weighs approx. 550 lbs. ( 250 kg) uncrated for a 66" machine. Wooden braces are strapped across the underside of its cross channels and the forklift arms should be raised to those braces when the machine is lifted.

CAUTIONWhen placing forklift arms under cross channels,

use care not to damage under carriage components.

Place power tilt cradle machine 15" [38 cm] from desired end of table, as shown in illustration on page 5. The cradle stand should be even with operator's side of the table. Level the power tilt cradle and secure to the floor, for proper and accurate edge control operation.

Mount the control box to the support frame (operator's side). Connect the Main Control Harness from the control box to the Harness Bracket, which is located on the power tilt cradle Stand.

Edge Upright Assembly InstallationLocate edge upright assembly sections in shipping crate and place on spreading table. Assemble upright assembly as shown in illustration on page 5. Locate Probe Assembly in shipping crate and mount to probe support on upright assembly. Connect the probe assembly wiring harness to the mating plug on cradle stand.

Place upright assembly at the edge of the spreading table, as shown in illustration on page 5. Square the edge upright assembly to the table and mark mounting hole location. Drill .344 dia. holes thru table top and secure in position with screws provided.

CAUTIONTo avoid damage to the wiring harness,

keep harness clear of material path.

WARNINGImproper loading of piece goods roll can result in personal injury and property damage. Improper unwinding direction can cause a pinch point in material and can eject piece goods roll from Power Tilt Cradle.

WARNINGKeep hands and loose objects away from Feed

Roller and Drive Belts.

OPERATION

NOTE: Refer to the control box familiarization on page 6 before reading this section.

Opening The CradleCheck opening path for obstructions. If the opening path is clear. Pull Main Power button on. Press the Load Control Switch to the Load position. Press and hold the Open/Close switch to the open position. Release when cradle is open. To close the cradle, press and hold the Open/Close switch to the close position. Release when cradle is closed. Press the Load Control Switch to the Edge position to begin operation.

Loading the CradlePlace the piece goods roll into the cradle. Move Alignment Bars against the ends of the piece goods roll and secure in position. Return cradle to operating position. Switch the load control switch to the edge position to begin operation.

NOTE: Refer to the control box familiarization on page 6 before reading this section.

CAUTIONMaximum weight of piece goods roll is 500 lbs.(227 kg)

and extreme caution should be used when placing piece goods roll into cradle.

ThreadingTurn Power Tilt Cradle on. Set controls to manual mode. Manually feed material up over the Roller Tube Assembly. Feed cloth under Dancer Bar and up over rollstand tube on edge upright assembly. See illustration on page 5. Thread fabric onto the Track & Chute Assembly of your Blue Jay End Cutter. Switch Power Cradle to Automatic mode and machine is ready for operation.

5Form CR-50-0437

THREADING DIAGRAMOPERATING ADJUSTMENTS

Dancer Bar AdjustmentTo set spring for material stiffness; loosen screw on shaft collar and turn collar to adjust tension on spring and retighten setscrew.Non-operator side- Adjust for lightweight, sheer material (ref. light cotton). Experimentation will yield best operational adjustment.Operator side- Adjust for heavier weight material (ref. vinyl). Experimentation will yield best operational adjustment.

Edge Control Sensitivity AdjustmentFactory set to be suitable for most fabrics. NOT affected by cutting room lighting. If adjustment is required the sensor must be removed for sensitivity adjustment. Each sensor has a countersunk adjusting screw on the bottom surface. Turn screw CLOCKWISE to INCREASE sensitivity, COUNTER-CLOCKWISE to DECREASE sensitivity. Use care not to damage lens of scanner. When relocating sensor on support, scanner lenses must be aimed perpen-dicular to refl ector for edge control to operate properly. Switch edge control to automatic and test for proper functioning.

Automatic Speed AdjustmentNot required. The Power Tilt Cradle automatically adjusts cradle speed during operation.

SERVICE AND MAINTENANCE

Daily:-Blow off entire machine and edge control probe.

Weekly:-Check for any unusual wear and determine why.

Bi-Monthly:-Check chain, tighten and lubricate.-Check entire machine for loose nuts and bolts.

EASTMAN # 500 POWER CRADLE

EASTMAN CRADLE

LOAD CONTROL

AutoCenter

EDGE CONTROL

2

LOW

10

23

456

78

9

76

5 432

98

01

012

331

0

SPREAD LENGTH IN INCHES

X 100X 10X 1X .25

HIGH

RETURNAUTOSTART/STOP

SPREAD

HIGH LOW

LEFT END SPEEDRIGHT END SPEED

LOW HIGHLOW HIGH

MAIN POWER

ONOFF

MACHINE CO.EASTMAN

12"

DancerBar

Edge UprightAssembly

Edge ControlProbe Assembly

GRIPPERON/OFF

GRIPPER

GRIPPER

UP

DOWN

MOVELEFT RIGHT

MOVE

BLUE JAYLIFT

JOYSTICKCONTROL

BLUEJAYCLAMP

CUTTER

ENDOVERRIDE

BLUE JAY

#500 CAPACITY

6

EASTMAN

Form CR-50-0437

®

1

2345

6

7

8

9

10

11

12

13141516

Main Drive Controls:

1. Main Power- Activates power to all circuits. Pull-on, Push off.2. Indicator Light- Indicates when Main Power (1) is activated.3. Auto/Manual- Sets Auto/Manual feed mode. Auto- Cradle feed operated by Dancer Bar. Manual- Cradle feed operated by Forward/Reverse switch.4. Feed Direction- Sets feed belt direction as indicated.5. Speed Adjustment- Sets speed of belt drive motor when in manual mode.6. Forward/Reverse- Press to manually roll or unroll material for threading.

Load Controls:

7. Close/Open- Press to open or close cradle8. Load/Edge- Press to set loading mode or edging mode.

FAMILIARIZATION CONTROL BOX EMERGENCY STOP

PRESS AT ANY TIMEDURING OPERATION

Edge Control Section:

9. Auto Center- Moves edge control platform to center position. Press and hold until platform stops.10. Auto/Manual- Sets Auto/Manual Edge Control mode.11. Manual- Moves platform in or out when in Manual mode.

BOTTOM PLATE:

12. Main Outlet- Connects Control Box to Main Wiring Harness.13. Circuit Breaker- (5 Amp): Tilt Power14. Circuit Breaker- (15 Amp): Main Power15. Circuit Breaker- (15 Amp): Main Power16. Circuit Breaker- (2 Amp): Edge Control Platform

BOTTOM PLATE:

7Form CR-50-0437

Pictorial Index

Control Box to Platform Connecting Harness # 11-2904

(Not Shown)

Probe Assembly

Emergency StopBox Assembly

Cradle Assembly

Control Box Assembly

Edge ControlPlatform Assembly

Edge Upright Assembly

8

EASTMAN

Form CR-50-0437

®

Dancer Bar Assembly

ITEM PART NO. DESCRIPTION QTY. 1 9120-097 Decal, Warning 2 2 335-34-8 Screw, Socket Hd. 1/4-20 x 1/2 4 3 SK-21534-MS Cross Alignment Bar 2 4 CR-40404-1 Cloth Alignment Bar, Right 1 5 CR-40404-2 Cloth Alignment Bar, Left 1 6 9124-098 Decal, Danger 2 7 C-12653 Knob 4 8 335-34-8 Screw, Socket Hd. 1/4-20 x 1/2 2 9 SY-10371-1 Block, Dancer Bar 2 10 9022-0206 Needle Bearing 2 11 410-36 Washer, Flat 5/16 4 12 402-36 Washer, Lock 5/16 4 13 335-36-16 Screw, Socket Hd. 5/16-18 x 1 4 14 410-34 Washer, Flat 1/4 2 15 WCH-11224 Holder 2 16 CH-152 Strap, Plastic 2 17 402-34 Washer, Lock 1/4 2 18 335-34-8 Screw, Socket Hd. 1/4-20 x 1/2 10 19 335-36-12 Screw, Socket Hd. 5/16-18 x 3/4 4 20 AD-02422 Stop, Cushion 4 21 9060-004 Shaft Collar 2 22 331-36-24 Screw, Socket Hd. 5/16-18 x 1 1/2 2 23 402-34 Washer, Lock 1/4 2 24 410-34 Washer, Flat 1/4 2 25 SK-21533 Dancer, Arm 2 SK-21533-1 Dancer, Long Arm 2*

ITEM PART NO. DESCRIPTION QTY. 26 TL-226 Stud, Roller Tube 2 SY-11804 Stand - Off, Motor 1 1/2Hp * 27 M-52 Bearing, Roller Tube 2 F-223 Bearing, Ball Flange * 28 SK-12954-MS Dancer Tube 1 29 335-102-12 Screw, Socket Hd. #10-32 x 3/4 2 30 CH-110 Tension Spring 1 31 9060-004 Shaft Collar 2 32 410-34 Washer, Flat 1/4 2 33 335-34-8 Screw, Socket Hd. 1/4-20 x 1/2 2 34 SK-12955-MS Pivot Bar 1 35 CH-110 Tension Spring 1 36 9009-0304 Sprocket, 48t 1 37 9139-032-001 Chain Assembly, Dancer 1 38 511-3-8 Roll Pin, 3/32 x 1/2 1 39 335-34-6 Screw, Socket Hd. 1/4-20 x 3/8 1 40 9009-0303 Sprocket, 13t 1 41 SK-12957 Bracket, Speed Pot 1 42 11-1819 Potentiometer, 5k 1 43 333-99-6 Screw, Button Hd. #10-24 x 3/8 2 44 SK-13317 Dancer Control Cover 1 45 333-99-6 Screw, Button Hd. #10-24 x 3/8 4 46 CR-13015 Mounting Bracket 2 47 344-86-3 Scr. Shssn 6-32 x 3/16 2 48 SK-21919 Wear Plates 2* 49 SK-13273 Spacer 1 50 SK-13272-108 Tube, Dancer Support 1 51 CH-2004 Guard 2

MS - Machine Size* - Optional

9Form CR-50-0437

1

2

3

4

5

6

78

910

1112 13

14

1516

17

18

1920

21

22232425

2627

2829

3031

3233

34

36

37 383940

41 42

43

4445

1

3

8

35

3132

33

2921

2223

2425 27

26

14

1516

1718

9

10

13

12 11

46

48

49

50

51

51

10

EASTMAN

Form CR-50-0437

®

Tilt Cradle Assembly SK-04663-MS

ITEM PART NO. DESCRIPTION QTY. 1 CR-04525-MS Back Roller Tube 1 2 CR-04524-MS Drive Roller Tube 1 3 CR-04526-MS Front Roller Tube 1 4 9013-014-MS Cradle Belt, Full Set 1 9013-016-MS Cradle Belt, HS, Full Set 1 5 SK-21785 Upper Link, Op Side 1 6 100-19-7 Pin 2 7 410-38 Washer, Flat 3/8 8 8 402-38 Washer, Lock 3/8 8 9 331-38-12 Screw, Hex Hd. 3/8-16 x 3/4 8 10 SK-40388-1 Side Frame, Op Side 1 11 335-34-8 Screw, Socket Hd. 1/4-20 x 1/2 8 12 402-51 Washer, Lock 3/4 2 13 CH-438 Hex Bolt, Special 2 14 CR-40282 Side Cover, Left 1 15 9124-125 Decal, 500# Tilt Cradle 2 16 333-99-6 Screw, Button Hd. #10-24 x 3/8 2 17 335-38-12 Screw, Socket Hd. 3/8-16 x 3/4 4 18 333-99-6 Screw, Button Hd. #10-24 x 3/8 4 19 CR-13015 Cover Bracket 2 20 335-38-12 Screw, Socket Hd. 3/8-16 x 3/4 4 21 335-38-40 Screw, Socket Hd. 3/8-16 x 2 1/2 8 22 CR-13016 Cam 2 23 410-010 Washer, Flat #10 4 24 402-010 Washer, Lock #10 4 25 335-99-8 Screw, #10-24 x 1/2 4 26 CR-40285-MS Cross Tube 2 27 SK-21784 Pivot Shaft 2 28 9040-028 Bushing, Pivot 2 29 411-57-2 Shim Washer 4 30 AD-12321 Retainer Disc 2 31 335-34-10 Screw, Socket Hd. 1/4-20 x 5/8 2 32 SK-40390-MS Cross Pivot Support Tube 1 33 CR-13115 Cam, Open 1 34 402-010 Washer, Lock #10 2

ITEM PART NO. DESCRIPTION QTY. 35 410-010 Washer, Flat #10 2 36 335-99-8 Screw, #10-24 x 1/2 2 37 11-1224L Motor, Cradle Drive, 3/4 hp 1 38 9009-0212 Sprocket, 12t 1 39 344-34-5 Setscrew, 1/4-20 x 5/6 2 40 331-36-20 Screw, Hex 5/16 -18 x 1 1/4 4 41 402-36 Washer, Lock 5/16 4 42 SY-10182 Pillow Block 2 43 206-38 Nut, Hex 3/8-16 2 44 357-38-32 Bolt, Hex Hd. 3/8-16 x 2 2 45 353-36-20 Carriage Bolt 5/16-18 x 1 1/4 12 46 9031-013 Flange Bearing 1" Bore 6 47 410-36 Washer, Flat 5/16 12 48 402-36 Washer, Lock 5/16 12 49 203-36 Nut, Hex 5/16-18 12 50 SK-21785-1 Upper Link, Non-Op Side 1 51 603-8-8-14 Key 1 52 9009-0283 Sprocket, 36t 1 53 9141-033-001 Chain 1 54 MD-02482 Chain Tensioner 1 55 402-34 Washer, Lock 1/4 1 56 335-34-8 Screw, Socket Hd. 1/4-20 x 1/2 1 57 331-34-8 Screw, Hex Hd. 1/4-20 x 1/2 1 58 333-99-6 Screw, Button Hd. #10-24 x 3/8 2 59 CR-40281 Side Cover, Right 1 60 333-99-6 Screw, Button Hd. #10-24 x 3/8 4 61 CR-13015 Cover Bracket 2 62 331-38-12 Screw, Hex Hd. 3/8-16 x 3/4 4 63 402-38 Washer, Lock 3/8 4 64 410-38 Washer, Flat 3/8 4 65 SK-40388-2 Side Frame, Non-Op Side 1 66 9058-005 Split Collar, 1.75 OD, .5W 6* 67 SK-12958-1 Belt Spacer, Nylon 3"I.D. A/R 68 342-102-6 Screw, Socket Hd. #10-32 x 3/4 A/RMS-Machine Size* - OptionalA/R - As Required

11Form CR-50-0437

1

23

4

56

789

1011

1213

1415

16

17

1819

20

21

22

23

2425

26

2728

2930

31

32

3334 35

36

464748

495051

52

53

54

5556

57

58

59

60

27

2829

3031

454443 42

4140

39

38

37

6

55

61

6263

6465

7 89

68

67

66

12

EASTMAN

Form CR-50-0437

®

Edge Control Platform Assembly SK-04664-MSITEM PART NO. DESCRIPTION QTY. 1 11-6019-1 Tilt Actuator 2 2 SK-40389-1-MS Platform Cover, Left 1 3 SK-40389-2-MS Platform Cover, Right 1 4 332-38-20 Screw, Flat Hd. 3/8-16 x 1 1/4 4 5 SY-10186 Washer, Retaining 4 6 9020-0209 Platform Bearing 8 7 SY-10188 Spacer 4 8 SK-13319 Platform Shaft 2 9 206-41 Ja m Nut, 7/16-20 2 10 410-44 Washer, Flat 1/2 4 11 AD-12373 Spacer, .625 i.d. 2 12 P-12762-2 Spacer, 510 i.d. 2 13 9028-005 Cam Follower 2 14 9028-006 Cam Follower, Eccentric 2 15 AD-12366 Square End Plug 4 16 SK-40391-MS Edge Control Platform 1 17 100-19-7 Pin 3 18 SK-13318 Connector Bracket, 9 Pin 1 19 335-99-8 Screw, Socket Hd, #10-24 x 1/2 2 20 SK-21560 Connector Bracket, 15 Pin 2 21 335-99-8 Screw, Socket Hd, 10-24 x 1/2 4 22 335-93-6 Screw, Socket Hd, #8-32 x 3/8 4 23 11-0241 Speed Control, 90 vdc 1 24 SK-40387 Electrical Component Plate 1 25 410-010 Washer, Flat #10 4 26 402-010 Washer, Lock #10 4 27 335-99-8 Screw, Socket Hd. #10-24 x 1/2 4 28 313-86-6 Screw , Round Hd. #6-32 x 3/8 6 29 11-1014 Relay, 24 vdc, dpdt 3 30 335-99-12 Screw, Socket Hd. #10-24 x 3/4 1 31 11-623 Rectifier, Bridge 1 32 CR-40317- Roll Support, Left 1 33 CR-40317-1 Load Support, Right 1 34 335-38-10 Screw, Socket Hd., 3/8-16 x 5/8 4 35 410-38 Washer, Flat 3/8 4 36 216-38 Flange Nut, 3/8-16 4 37 SK-13316 Roll Support Tube 2 38 9124-125 Decal, 500# Tilt Cradle 1 39 AD-12360 Liner, Guide 4 40 335-36-12 Screw, Socket Hd. 5/16-18 x 3/4 8 41 AD-12575-1 Shim, 1/32 A/R 42 AD-12575-2 Shim, 1/16 A/R 43 AD-12359 Block, Guide 4 44 402-36 Washer, Lock 5/16 8 45 335-36-12 Screw, Socket Hd. 5/16-1 x 3/4 8 46 402-38 Washer, Lock 3/8 4 47 335-38-10 Screw, Socket Hd., 3/8-16 x 5/8 4

ITEM PART NO. DESCRIPTION QTY. 48 SK-40386 Mounting Bracket, Control Box 1 49 402-010 Washer, Lock #10 4 50 335-99-8 Screw, Socket Hd., #10-24 x 1/2 4 51 335-99-8 Screw, Socket Hd., #10-24 x 1/2 2 52 SK-21457 Bracket, Electrical Harness 2 53 SK-13289 Bracket, Edge Sensor 1 54 335-99-8 Screw, Socket Hd., #10-24 x 1/2 2 55 SK-40392-MSLower Platform 1 56 11-2909 Limit Switch Assembly (Std.) 1 11-2909-1 Limit Switch Assembly (m/i) 1 57 313-86-18 Screw, Round Hd. #6-32 x 1/8 6 58 410-060 Washer, Lock #6 6 59 11-1168 Switch, Limit 2 60 11-1167 Switch Cover 2 61 11-4120 Switch, Limit 1 62 AD-12532 Mount 1 63 335-34-10 Screw, Socket Hd. 1/4-20 x 5/8 2 64 402-34 Washer, Lock 1/4 2 65 410-34 Washer, Flat 1/4 2 66 332-99-10 Washer, Flat, #10-24 x 5/8 2 67 AD-21285 Mounting Plate 1 68 335-34-8 Screw, Socket Hd. 1/4-20 x 1/2 2 69 SK-21497 Spacer Tube 1 71 335-99-8 Screw, Socket Hd., #10-24 x 1/2 2 72 332-99-8 Screw, Flat Hd, #10-24 x 1/4 4 73 SK-21561 Transformer Plate, (220 v only) 1 74 11-1625-1 Transformer, (220 v only) 1 75 402-010 Washer, Lock #10 4 76 203-99 Nut, Hex #10-24 4 77 402-010 Washer, Lock #10 2 78 335-99-8 Screw, Socket Hd., #10-24 x 1/2 2 79 11-6025 Edge Control Actuator 1 80 SK-13321 Cradle Mount 2 81 335-99-8 Screw, Socket Hd., #10-24 x 1/2 4 82 11-1174 Limit Switch 2 83 11-4184 Limit Switch 1 84 335-99-8 Screw, Socket Hd. #10-24 x 1/2 2 85 402-010 Washer, Lock #10 2 86 410-010 Washer, Flat #10 2 87 SK-13320 Cam Mount, Centering 1 88 AD-12361 Centering Cam 1 89 402-010 Washer, Lock #10 2 90 333-102-6 Screw, Button Hd. #10-32 x 3/8 2 91 SK-21786 Cam, Edge 1 92 402-010 Washer, Lock #10 2 93 335-102-6 Screw, Socket Hd. #10-32 x 3/8 2MS-Machine Size A/R - As Required

13Form CR-50-0437

61

62

6364

6566

67

48

4950

51

52

53

54

5556

5758

5960

1

1

2

3

4567

891011

4 5 6 7

12

1314

15

16

1718

910

19

2120

A

A

B

C

B

2223

2425

2627

2892 29

30

3132

333435

36

37

39 40

41, 4243

4547

46

17

20

21

17

373638

44

68

69

5758

52

71

72

7374

7576

7778

79

8180

8382

93

908988

85

848687

91

C

500# Power Cradle

Eastman®

14

EASTMAN

Form CR-50-0437

®

Control Box Assembly 11-2906

ITEM PART NO. DESCRIPTION QTY. 1 11-4173 Switch, Momentary 3 2 11-4178 Switch, Rocker 3 3 11-4171 Switch 1 4 11-1012-3 Knob, Timer 1 5 11-1829 Potentiometer 1 6 11-1190 Button Switch 1 7 11-1252 Lamp, Neon 1 8 11-4139 Push button, Emer. Stop 1 9 313-86-6 Screw, Rd. Hd. #6-32 x 3/8 6 10 11-843-4 Panel Cabinet, Power Cradle 1 11 203-86 Nut, Fin. Hex #6-32 8 12 11-4730 Plug, Circular 37 Pin Flanged 1 13 11-1333-5 Fuse, Circuit Breaker, 5 Amp 1 14 11-1333-15 Circuit Breaker, 15 Amp 2 15 11-1333-2 Fuse, Circuit Breaker, 2 Amp 1 16 11-4143 Block, Contact, N.C., K-Moeller 2 17 11-165-1 Board, Edge Control 1 18 313-86-8 Screw, Rd. Hd. #6-32 x 1/2 2 19 203-86 Nut, Hex Machine Screw #6-32 4 20 11-1025 Strip, Terminal 4-140 Cinch 1 21 SK-21544 Bottom Plate, Control Box 1 22 11-4138 Adapter, Mounting, K-Moeller 1 23 11-2843 Power Supply, Roll Stand 1 24 318-102-12 Screw, Pan Hd. #10-32 x 3/4 2 25 203-102 Nut, Machine Screw #10-32 2 26 11-527 Resistor, 50 Ohms 55W, 5% 1 27 9124-124 Decal, Tilt Control Box 1 28 SK-13322 Nut Plate, Control Box 1

Control Box to Platform Connecting Harness # 11-2904

(Not Shown)

15Form CR-50-0437

23

1

32

1

21

7

8

4 5

6

9

10 5

6

1514

12

13

9

18

9

17

1920

10

9

8

16

11

21

22

24

25 26

27

11

28

2

16

EASTMAN

Form CR-50-0437

®

ITEM PART NO. DESCRIPTION QTY. 1 SK-30598 Box, Plastic 1 2 11-4143 Block, Contact, N.C. 1 3 11-4142 Block, Contact, N.O. 1 4 11-4138 Adapter, Mounting 1 5 11-4139 Pushbutton, Emer. Stop 1 6 203-86 Nut, Hex #6-32 2 7 9124-099 Decal, Emergency Stop 1 8 332-86-6 Screw, Skt. Hd. Cap #6-32 x 3/8 2 9 11-1935 Bracket, Resistor Mounting 2 10 11-1803 Resistor, 5 Ohm, 25 Watt 1

Emergency Stop Box Assembly 11-2912

1

1

1

1

2

3

4

5

7

8

9

5

10

6

17Form CR-50-0437

Power Cradle Probe Assembly SK-03291

ITEM PART NO. DESCRIPTION QTY. 1 335-99-8 Screw, Socket Hd. #10-24 x 1/2 1 2 342-99-4 Setscrew, #10-24 x 1/4 1 3 CHTW-11559 Probe Mount Block 1 4 SK-21846 Probe Bracket 1 5 SK-13398 Sensor Mounting Plate 2 6 410-060 Washer, Flat #6 4 7 402-60 Washer, Lock #6 4 8 335-86-8 Screw, Socket Hd. #6-32 x 1/2 4 9 335-86-8 Screw, Socket Hd. #6-32 x 1/2 2 10 11-167 Sensor, Eye 2 11-2910 Sensors with Connector Assembly 1 11 341-3-10 Screw, Socket Hd. M3-10mm metric 4 12 11-167-2 Super Reflective Tape 1 13 11-4736 Connector Clamp 1 14 11-4747 Connector, 4 pin 1 15 11-4706 Pin, Male 4

1

23

4

56 7 8

9

10

11

1213

14

15

18

EASTMAN

Form CR-50-0437

®

12 3 4

56

7 818

9

8 18

7 6 5

3 21

111213

1

4

1

14

32

16317

14

216

32

16

10

15

3216

Edge Upright Assembly SK-04473-MS

ITEM PART NO. DESCRIPTION QTY. 1 331-36-16 Screw, Hex Hd. Cap 5/16-18 x 1 6 2 402-36 Washer, Lock 5/16 10 3 410-36 Washer, Flat 5/16 10 4 PS-31 Upright, Bottom Back 2 5 411-44-2 Washer, Fiber 1/2 x 3/4 x 1/16 6 6 PM-16 Stud, Nip Roller Short 2 7 F-228 Bearing, Flanged 2 8 TT-10 Collar, 1.250 2 9 SK-11528-MS Tube, Roller 110 CH-493 Lamp Support, Edge Control 111 410-38 Washer, Flat 3/8 112 402-38 Washer, Lock 3/8 113 335-38-12 Screw, Skt. Hd. Cap 3/8-16 x 3/4 114 332-36-40 Screw, Skt. Flat Head 5/16-18 x 2-1/2 415 SK-12952 Angle Support, Oper. Side 116 203-36 Nut, Fin. Hex 5/16-18 817 SK-12953 Angle Support, Non-oper. Side 118 344-34-6 Setscrew, 1/4-20 x 3/8 2

MS - Machine Size

19Form CR-50-0437

Reverse Roll Assembly CR-04575-MS (Optional)

Item numbers are for reference only. Please Specify PART NUMBER whenordering replacement parts.

ITEM PART NO. DESCRIPTION QTY. 1 355-38-8 Shoulder Bolt, 3/8-1/2 2 2 9001-0004 Nylon Washer, 3/8 6 3 CR-13345 Link, Short 1 4 CR-13191 Spacer 2 5 9026-0002 Bearing 2 6 CR-13167 Hub 2 7 9068-010 Roller Covering A/R 8 SK-21535-A-MS Roller Tube 1 9 CR-13190-72 Roller Tube Shaft 1 10 CR-13192 Link, Long 1 11 344-34-4 Setscrew, 1/4-20 x 1/4 2 12 335-36-6 Screw, Socket Head 5/16-18 x 1 1 13 402-36 Washer, Lock 5/16 1 14 M-85 Knob 1 15 TP-13 Pin, Pull 1

MS- Machine SizeA/R -As Required

22

3 45

6

1

2

2

1

78

9

6

54

10

11

11

1213

1415

20

EASTMAN

Form CR-50-0437

®

Power Cradle Uprights Assembly (Optional) SK-04634Includes Left & Right Uprights Item numbers are for reference only.

Please Specify PART NUMBER whenordering replacement parts.

ITEM PART NO. DESCRIPTION QTY. 1 SY-10412-2 Stud, Stop 1 2 331-38-28 Screw, Hex Head 3/8-16 x 3/4 4 3 SY-11753 Spacer 1 4 331-38-28 Screw, Hex Head 3/8-16 x 1 3/4 2 5 SK-30552-1 Batwing, Left 1 SK-30552-2 Batwing, Right 1 6 SY-10208 Bushing 2 7 9020-0203 Bearing, Uprights 2 8 410-38 Washer, Flat 3/8 6 9 216-38 Nut, Flange 3/8-16 6 10 205-38 Nut, Hex 3/8-16 1 11 410-36 Washer, Flat 5/16 1 12 402-36 Washer, Lock 5/16 1 13 335-36-12 Screw, Socket Head 5/16-18 x 3/4 1 14 AD-03186 Upright (20" only) 1 AD-03171-3 Upright (40" only) 1 15 410-38 Washer, Flat 3/8 1 16 402-38 Washer, Lock 3/8 1 17 335-38-12 Screw, Socket Head 3/8-16 x 3/4 4 18 216-38 Nut, Flange 3/8-16 4

12

3

4

5 6

7 8 9

10

11

12

13

14

15

16

17

18

89

Brake AsssemblyNot Included

21Form CR-50-0437

1

23

4

56

7

8

9

10

11

1213

1415

164

5

ITEM PART NO. DESCRIPTION QTY. 1 SY-11756 Pin 1 2 SY-02307 Handle 1 3 SY-11758 Rod 1 4 SY-02305 Arm 2 5 SY-11762 Leather, Brake Pad 2 6 332-102-6 Screw, Flat Head Socket 10-32 x 3/8 2 7 9004-0226 Spring 1 8 355-44-32 Screw, Shoulder Socket 1/2 x 2 1 9 SY-11753 Spacer 1 10 SY-11752 Block, Rocker 1 11 SY-11761 Knob 1 12 335-36-12 Screw, Socket Head Cap 5/16-18 x 3/4 1 13 402-36 Washer, Lock 5/16 1 14 410-36 Washer, Flat 5/16 1 15 SY-10412-2 Stud, Stop 1 16 216-38 Nut, Flange 3/8-16 1

Item numbers are for reference only. Please Specify PART NUMBER whenordering replacement parts.

Brake Assembly SY-03098 (Optional)

22

EASTMAN

Form CR-50-0437

®

ITEM PART NO. DESCRIPTION QTY. 1 PM-11373 Coupling 1 2 532-4-16 Dowel Pin 1 3 PM-20737 Shaft 1 4 PM-20752 Sleeve 1 5 344-34-3 Setscrew 1/4-20 x 3/16 2 6 SY-11583 Shifter 1 7 PM-20742-1 Cloth Stop 1 8 335-36-24 Screw, Socket Hd. 5/16-18 x 1 1/2 1 9 9001-0007 Washer, Nylon 1 10 9060-004 Collar, Shaft 1 11 342-35-4 Setscrew 1/4-28 x 1/4 1 12 CHT-424-2 Hand wheel 1 13 344-34-6 Setscrew 1/4-20 x 3/8 1 14 332-102-6 Screw, Flat Hd. 10-32 x 3/8 * 15 532-4-12 Dowel Pin A/R 16 PM-11374 Bushing, Clevis A/R 17 PM-11439 Link A/R 18 332-93-8 Screw, Flat Hd. 8-32 x 1/2 A/R 19 PM-11393 Rivet A/R 20 335-102-6 Screw, Socket Hd. 10-32 x 3/8 A/R 21 344-102-5 Setscrew 10-32 x 5/16 A/R 22 PM-11387-MS Rod, Pull 1 23 332-99-6 Screw, Flat Hd. 3/8 4 24 332-102-8 Screw, Flat Hd. 10-32 x 1/2 A/R 25 PM-20738-MS Tube, Housing 1 26 511-6-22 Roll Pin 1 27 SY-21085 Rod End, Expandabar 1A/R - As Required MS-Machine Size

Heavy Duty (#300) Expandabar SY-04285-MS (Optional)

15

14

191521

16

20

2324

24

24

24

24

26

2725

22

1

2 3 4

7

8

9

10

1418 17

16

11

13

12

23Form CR-50-0437

15

14

191521

16

20

2324

24

24

24

24

26

2725

22

1

2 3 4

7

8

9

10

1418 17

16

11

13

12

24

EASTMAN

Form CR-50-0437

®

ITEM PART NO. DESCRIPTION QTY. 1 PM-11373 Coupling 1 2 532-4-16 Dowel Pin 1 3 PM-20737 Shaft 1 4 SY-30272 Sleeve 1 5 344-34-3 Setscrew 1/4-20 x 3/16 2 6 SY-20818 Shifter 1 7 PM-20742-2 Cloth Stop 1 8 335-36-24 Screw, Socket Hd. 5/16-18 x 1 1/2 1 9 9001-0007 Washer, Nylon 1 10 9060-004 Collar, Shaft 1 11 342-35-4 Setscrew 1/4-28 x 1/4 1 12 9077-003 Hand wheel 1 13 344-34-6 Setscrew 1/4-20 x 3/8 1 14 332-102-8 Screw, Flat Hd. 10-32 x 1/2 A/R

ITEM PART NO. DESCRIPTION QTY. 15 532-4-12 Dowel Pin A/R 16 SY-20816 Bushing, Clevis A/R 17 PM-11439 Link A/R 18 332-93-10 Screw, Flat Hd. 8-32 x 5/8 A/R 19 PM-11393 Rivet A/R 20 335-102-8 Screw, Socket Hd. 10-32 x 1/2 A/R 21 344-102-6 Setscrew 10-32 x 3/8 A/R 22 SY-11612-MS Rod, Pull 1 23 332-99-6 Screw, Flat Hd. 3/8 4 24 332-102-8 Screw, Flat Hd. 10-32 x 1/2 A/R 25 SY-30271-MS Tube, Housing 1 26 511-6-28 Roll Pin 1 27 SY-20817 Rod End, Expandabar 1A/R - As Required MS-Machine Size

1

23

4

5

6

7 89

10

11

13

12

15

14

16

14

191521

16

2018 17

2324

24

24

24

24

26

27

25

22

Heavy Duty (#500) Expandabar SY-04166-MS (Optional)

25Form CR-50-0437

1 1/4" Dia. Solid Bar SY-02383-MS (Optional)

ITEM PART NO. DESCRIPTION QTY. 1 SY-10413 Shifter 1 2 344-36-5 Setscrew 5/16-18 x 5/16 2 3 F-226-D Cone, 1 1/4 Bore 2 4 335-36-20 Screw, Socket Head 5/16-18 x 1 1/4 1 5 SY-10427-MS Bar, Rayon 1 1/4 Dia. 1 6 387-36-20 Screw, Thumb 5/16-18 x 1 1/4 1MS-Machine Size

1

2

3

4

5

3

6

26

EASTMAN

Form CR-50-0437

®

Tilt

Cra

dle

Elec

tric

al S

chem

atic

B

lue

Prin

t No.

11-

2952

27Form CR-50-0437

Tilt

Cra

dle

Elec

tric

al D

iagr

am

Blu

e Pr

int N

o. 1

1-29

53

779 Washington St., Buffalo, N.Y. 14203-1396 U.S.A. • (716)856-2200 • Fax (716)856-1140 or (716)856-2068Manufacturers of Eastman Cloth Cutting and Cloth Spreading Machines

Website: www.EastmanCuts.com

EASTMAN®

TECHNICAL DATA Eastman Power Tilt Cradle®

Power CradleRoll Capacity ............................................................ 500 lbs. (227 kg)Edge Accuracy.......................................................... +/- 1/8" (+/- 3mm)Max. Machine Speed ......................................... 100 yds./min. (92m/min.)Power Requirement ........................................... 110V/220V (50/60 Hz)Max. Roll Diameter .............................................. 32 in. (81 cm)Max. Roll Width ................................................... 96 in. (2438 mm)Machine Weight ................................................. 550 lbs. (250 kg)

* Relative to the type and quality of fabric, spreading speed, spreading mode, track guidance, roll weight, etc.

Form CR-50-0437 © 2001, 2005 Eastman Machine Company Printed in U.S.A.06/2011

Limited Warranty. Eastman warrants to the buyer that the equipment shall be free from defects in ma-terials or workmanship for a period of 180 days commencing on the date of invoice. Any goods or parts claimed by the buyer to be defective must be returned to Eastman, freight charges prepaid, within the 180 day warranty period. If Eastman determines that the goods or parts are defective in materials or workmanship, Eastman’s sole obligation under this warranty shall be, at Eastman’s sole option, to repair or replace the defective goods or parts or to provide the buyer a credit equal to the portion of the pur-chase price allocable to the defective goods or parts. This warranty shall not apply if defects are caused by product misuse or neglect, if the machine has been altered or modified by the buyer, or if other than genuine Eastman belts, emery wheels, knives or parts are used in the machine. THIS WARRANTY IS THE ONLY WARRANTY APPLICABLE TO THIS PURCHASE. SELLER DISCLAIMS ALL OTHER WAR-RANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

Limitation of Liability. Eastman’s liability to the buyer, and the buyer’s remedies from Eastman, whether in contract, negligence, tort, under any warranty or otherwise, shall be limited to the remedies provided in the foregoing Limited Warranty. In no event shall Eastman have any responsibility or liability to the buyer for (a) any special, indirect, incidental, or consequential damages, including, but not limited to, loss of use, revenue, or profit, even if Eastman has been advised of the possibility of such damages, or (b) any claim against the buyer by any third party. The price stated for the product sold is a consideration for limiting Eastman’s liability.