testing iso/iec 17025:2017 for autoparts and ...iapht.org/certi/nabl_mechanical.pdfcopper alloy zn...
TRANSCRIPT
TESTING AND EVALUATION LABORATORY, INSTITUTEFOR AUTOPARTS AND HAND TOOLS TECHNOLOGY
has been assessed and accredited in accordance with the standard
ISO/IEC 17025:2017''General Requirements for the Competence of Testing &
Calibration Laboratories''for its facilities at
A9, PHASE V, FOCAL POINT, LUDHIANA, PUNJAB, INDIA
in the field of
TESTINGCertificate Number: TC-5628
Issue Date: 12/07/2019 Valid Until: 11/07/2021
This certificate remains valid for the Scope of Accreditation as specified in the annexure subject to continuedsatisfactory compliance to the above standard & the relevant requirements of NABL.
(To see the scope of accreditation of this laboratory, you may also visit NABL website www.nabl-india.org)
Signed for and on behalf of NABL
N. VenkateswaranChief Executive Officer
S.No Discipline / Group Product / Material ofTest
Specific TestPerformed
Test MethodSpecificationagainst which testsare performed
Range of Testing/Limits of Detection
Permanent Facility
1 CHEMICAL- METALS& ALLOYS
Aluminium &Aluminium Alloy
Cu ASTM E 1251: 2011 0.1 % to 22 %
2 CHEMICAL- METALS& ALLOYS
Aluminium &Aluminium Alloy
Fe ASTM E 1251: 2011 0.1 % to 3.3 %
3 CHEMICAL- METALS& ALLOYS
Aluminium &Aluminium Alloy
Mg ASTM E 1251: 2011 0.01 % to 11 %
4 CHEMICAL- METALS& ALLOYS
Aluminium &Aluminium Alloy
Mn ASTM E 1251: 2011 0.01 % to 12 %
5 CHEMICAL- METALS& ALLOYS
Aluminium &Aluminium Alloy
Ni ASTM E 1251: 2011 0.01 % to 11 %
6 CHEMICAL- METALS& ALLOYS
Aluminium &Aluminium Alloy
Pb ASTM E 1251: 2011 0.01 % to 1 %
7 CHEMICAL- METALS& ALLOYS
Aluminium &Aluminium Alloy
Si ASTM E 1251: 2011 0.05 % to 25 %
8 CHEMICAL- METALS& ALLOYS
Aluminium &Aluminium Alloy
Sn ASTM E 1251: 2011 0.01 % to 1 %
9 CHEMICAL- METALS& ALLOYS
Aluminium &Aluminium Alloy
Ti ASTM E 1251: 2011 0.01 % to 0.30 %
10 CHEMICAL- METALS& ALLOYS
Aluminium &Aluminium Alloy
Zn ASTM E 1251: 2011 0.01 % to 13 %
11 CHEMICAL- METALS& ALLOYS
Aluminum & its alloys Cr ASTM 1251: 2011 0.01 % to 0.37 %
12 CHEMICAL- METALS& ALLOYS
Carbon steel and lowalloy steel
Al ASTM E 415: 2015 0.010 % to 0.60 %
13 CHEMICAL- METALS& ALLOYS
Carbon steel and lowalloy steel
B ASTM E 415: 2015 0.001 % to 0.01 %
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name TESTING AND EVALUATION LABORATORY, INSTITUTE FOR AUTOPARTS ANDHAND TOOLS TECHNOLOGY, A9, PHASE V, FOCAL POINT, LUDHIANA, PUNJAB ,INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number TC-5628 Page No. : 1 / 23
Validity 12/07/2019 to 11/07/2021 Last Amended on -
S.No Discipline / Group Product / Material ofTest
Specific TestPerformed
Test MethodSpecificationagainst which testsare performed
Range of Testing/Limits of Detection
14 CHEMICAL- METALS& ALLOYS
Carbon steel and lowalloy steel
C ASTM E 415 : 2015 0.02 % to 1.5 %
15 CHEMICAL- METALS& ALLOYS
Carbon steel and lowalloy steel
Cr ASTM E 415: 2015 0.010 % to 3.0 %
16 CHEMICAL- METALS& ALLOYS
Carbon steel and lowalloy steel
Cu ASTM E 415: 2015 0.02 % to 1.1 %
17 CHEMICAL- METALS& ALLOYS
Carbon steel and lowalloy steel
Mn ASTM E 415 : 2015 0.05 % to 19 %
18 CHEMICAL- METALS& ALLOYS
Carbon steel and lowalloy steel
Mo ASTM E 415: 2015 0.010 % to 1.0 %
19 CHEMICAL- METALS& ALLOYS
Carbon steel and lowalloy steel
N ASTM E 415: 2015 0.002 % to 0.9 %
20 CHEMICAL- METALS& ALLOYS
Carbon steel and lowalloy steel
Nb ASTM E 415: 2015 0.004 % to 0.15 %
21 CHEMICAL- METALS& ALLOYS
Carbon steel and lowalloy steel
Ni ASTM E 415: 2015 0.01 % to 4.5 %
22 CHEMICAL- METALS& ALLOYS
Carbon steel and lowalloy steel
P ASTM E 415 : 2015 0.002 % to 0.12 %
23 CHEMICAL- METALS& ALLOYS
Carbon steel and lowalloy steel
S ASTM E 415: 2015 0.001 % to 0.4 %
24 CHEMICAL- METALS& ALLOYS
Carbon steel and lowalloy steel
Si ASTM E 415: 2015 0.01 % to 2.1 %
25 CHEMICAL- METALS& ALLOYS
Carbon steel and lowalloy steel
Ti ASTM E 415: 2015 0.001 % to 0.20 %
26 CHEMICAL- METALS& ALLOYS
Carbon steel and lowalloy steel
V ASTM E 415: 2015 0.002 % to 0.5 %
27 CHEMICAL- METALS& ALLOYS
Cast Iron C ASTM E 1999: 2018 1.90 % to 3.80 %
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name TESTING AND EVALUATION LABORATORY, INSTITUTE FOR AUTOPARTS ANDHAND TOOLS TECHNOLOGY, A9, PHASE V, FOCAL POINT, LUDHIANA, PUNJAB ,INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number TC-5628 Page No. : 2 / 23
Validity 12/07/2019 to 11/07/2021 Last Amended on -
S.No Discipline / Group Product / Material ofTest
Specific TestPerformed
Test MethodSpecificationagainst which testsare performed
Range of Testing/Limits of Detection
28 CHEMICAL- METALS& ALLOYS
Cast Iron Cr ASTM E 1999: 2018 0.01 % to 2.00 %
29 CHEMICAL- METALS& ALLOYS
Cast Iron Cu ASTM E 1999: 2018 0.015 % to 0.75 %
30 CHEMICAL- METALS& ALLOYS
Cast Iron Mn ASTM E 1999: 2018 0.1 % to 2.0 %
31 CHEMICAL- METALS& ALLOYS
Cast Iron Mo ASTM E 1999: 2018 0.01 % to 0.60 %
32 CHEMICAL- METALS& ALLOYS
Cast Iron Ni ASTM E 1999: 2018 0.020 % to 2.50 %
33 CHEMICAL- METALS& ALLOYS
Cast Iron P ASTM E 1999: 2018 0.001 % to 1.0 %
34 CHEMICAL- METALS& ALLOYS
Cast Iron S ASTM E 1999: 2018 0.010 % to 0.20 %
35 CHEMICAL- METALS& ALLOYS
Cast Iron Si ASTM E 1999: 2018 0.15 % to 3.0 %
36 CHEMICAL- METALS& ALLOYS
Cobalt & its alloys Al DC-176/00/01/01/2019:2019
0.001 % to 1.5 %
37 CHEMICAL- METALS& ALLOYS
Cobalt & its alloys C DC-176/00/01/01/2019:2019
0.002 % to 2.6 %
38 CHEMICAL- METALS& ALLOYS
Cobalt & its alloys Cr DC-179/00/01/01/2019:2019
8.5 % to 35.00 %
39 CHEMICAL- METALS& ALLOYS
Cobalt & its alloys Cu DC-176/00/01/01/2019:2019
0.002 % to 0.15 %
40 CHEMICAL- METALS& ALLOYS
Cobalt & its alloys Fe DC-176/00/01/01/2019:2019
0.005 % to 3.4 %
41 CHEMICAL- METALS& ALLOYS
Cobalt & its alloys Mn DC-176/00/01/01/2019:2019
0.002 % to 2.25 %
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name TESTING AND EVALUATION LABORATORY, INSTITUTE FOR AUTOPARTS ANDHAND TOOLS TECHNOLOGY, A9, PHASE V, FOCAL POINT, LUDHIANA, PUNJAB ,INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number TC-5628 Page No. : 3 / 23
Validity 12/07/2019 to 11/07/2021 Last Amended on -
S.No Discipline / Group Product / Material ofTest
Specific TestPerformed
Test MethodSpecificationagainst which testsare performed
Range of Testing/Limits of Detection
42 CHEMICAL- METALS& ALLOYS
Cobalt & its alloys Mo DC-176/00/01/01/2019:2019
0.005 % to 8.5 %
43 CHEMICAL- METALS& ALLOYS
Cobalt & its alloys Ni DC-176/00/01/01/2019:2019
0.005 % to 42.00 %
44 CHEMICAL- METALS& ALLOYS
Cobalt & its alloys P DC-176/00/01/01/2019:2019
0.001 % to 0.05 %
45 CHEMICAL- METALS& ALLOYS
Cobalt & its alloys S DC-176/00/01/01/2019:2019
0.001 % to 0.040 %
46 CHEMICAL- METALS& ALLOYS
Cobalt & its alloys Si DC-176/00/01/01/2019:2019
0.005 % to 2.3 %
47 CHEMICAL- METALS& ALLOYS
Cobalt & its alloys W DC-176/00/01/01/2019:2019
0.05 % to 16.00 %
48 CHEMICAL- METALS& ALLOYS
Copper & Its alloy Al BS EN 15079: 2015 0.01 % to 12.0 %
49 CHEMICAL- METALS& ALLOYS
Copper & its alloy Cr BS EN 15079: 2015 0.0001 % to 2.5 %
50 CHEMICAL- METALS& ALLOYS
Copper & Its alloy Fe BS EN 15079: 2015 0.01 % to 6.5 %
51 CHEMICAL- METALS& ALLOYS
Copper & its alloy Ni BS EN 15079: 2015 0.01 % to 35.00 %
52 CHEMICAL- METALS& ALLOYS
Copper & its alloy P BS EN 15079: 2015 0.002 % to 1.1 %
53 CHEMICAL- METALS& ALLOYS
Copper & Its alloy Pb BS EN 15079: 2015 0.01 % to 22 %
54 CHEMICAL- METALS& ALLOYS
Copper & its alloy Sn BS EN 15079: 2015 0.01 % to 22 %
55 CHEMICAL- METALS& ALLOYS
Copper Alloy Zn BS EN 15079: 2015 0.01 % to 46 %
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name TESTING AND EVALUATION LABORATORY, INSTITUTE FOR AUTOPARTS ANDHAND TOOLS TECHNOLOGY, A9, PHASE V, FOCAL POINT, LUDHIANA, PUNJAB ,INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number TC-5628 Page No. : 4 / 23
Validity 12/07/2019 to 11/07/2021 Last Amended on -
S.No Discipline / Group Product / Material ofTest
Specific TestPerformed
Test MethodSpecificationagainst which testsare performed
Range of Testing/Limits of Detection
56 CHEMICAL- METALS& ALLOYS
Nickel & its Alloy Al DC-177/00/01/01/2019:2019
0.005 % to 7.0 %
57 CHEMICAL- METALS& ALLOYS
Nickel & its Alloy B DC-177/00/01/01/2019:2019
0.0001 % to 3.2 %
58 CHEMICAL- METALS& ALLOYS
Nickel & its Alloy C DC-177/00/01/01/2019:2019
0.001 % to 1.5 %
59 CHEMICAL- METALS& ALLOYS
Nickel & its Alloy Co DC-177/00/01/01/2019:2019
0.001 % to 23.00 %
60 CHEMICAL- METALS& ALLOYS
Nickel & its Alloy Cr DC-177/00/01/01/2019:2019
0.001 % to 33.00 %
61 CHEMICAL- METALS& ALLOYS
Nickel & its Alloy Cu DC-177/00/01/01/2019:2019
0.005 % to 50.00 %
62 CHEMICAL- METALS& ALLOYS
Nickel & its Alloy Fe DC-177/00/01/01/2019:2019
0.001 % to 52.00 %
63 CHEMICAL- METALS& ALLOYS
Nickel & its Alloy Mn DC-177/00/01/01/2019:2019
0.001 % to 3.00 %
64 CHEMICAL- METALS& ALLOYS
Nickel & its Alloy Mo DC-177/00/01/01/2019:2019
0.001 % to 35.00 %
65 CHEMICAL- METALS& ALLOYS
Nickel & its Alloy N DC-177/00/01/01/2019:2019
0.0004 % to 0.03 %
66 CHEMICAL- METALS& ALLOYS
Nickel & its Alloy Nb DC-177/00/01/01/2019:2019
0.001 % to 8.00 %
67 CHEMICAL- METALS& ALLOYS
Nickel & its Alloy Si DC-177/00/01/01/2019:2019
0.001 % to 6.00 %
68 CHEMICAL- METALS& ALLOYS
Nickel & its Alloy Ti DC-00/01/01/2019:2019
0.0005 % to 6.5 %
69 CHEMICAL- METALS& ALLOYS
Stainless Steel Al ASTM E 1086: 2014 0.001 % to 0.20 %
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name TESTING AND EVALUATION LABORATORY, INSTITUTE FOR AUTOPARTS ANDHAND TOOLS TECHNOLOGY, A9, PHASE V, FOCAL POINT, LUDHIANA, PUNJAB ,INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number TC-5628 Page No. : 5 / 23
Validity 12/07/2019 to 11/07/2021 Last Amended on -
S.No Discipline / Group Product / Material ofTest
Specific TestPerformed
Test MethodSpecificationagainst which testsare performed
Range of Testing/Limits of Detection
70 CHEMICAL- METALS& ALLOYS
Stainless Steel C ASTM E 1086: 2014 0.01 % to 0.8 %
71 CHEMICAL- METALS& ALLOYS
Stainless Steel Cr ASTM E 1086: 2014 8.00 % to 33 %
72 CHEMICAL- METALS& ALLOYS
Stainless steel Cu ASTM E 1086: 2014 0.05 % to 4.00 %
73 CHEMICAL- METALS& ALLOYS
Stainless Steel Mn ASTM E 1086: 2014 0.10 % to 2.0 %
74 CHEMICAL- METALS& ALLOYS
Stainless Steel Mo ASTM E 1086: 2014 0.03 % to 11.00 %
75 CHEMICAL- METALS& ALLOYS
Stainless Steel Nb ASTM E 1086: 2014 0.01 % to 2.8 %
76 CHEMICAL- METALS& ALLOYS
Stainless Steel Ni ASTM E 1086: 2014 0.30 % to 45.00 %
77 CHEMICAL- METALS& ALLOYS
Stainless Steel P ASTM E 1086: 2014 0.003 % to 0.05 %
78 CHEMICAL- METALS& ALLOYS
Stainless Steel S ASTM E 1086: 2014 0.003 % to 0.40 %
79 CHEMICAL- METALS& ALLOYS
Stainless Steel Si ASTM E 1086: 2014 0.10 % to 1.4 %
80 CHEMICAL- METALS& ALLOYS
Stainless Steel Ti ASTM E 1086: 2014 0.01 % to 0.60 %
81 CHEMICAL- METALS& ALLOYS
Titanium & titaniumAlloy
Al DC-179/00/01/01/2019:2019
0.0005 % to 9.00 %
82 CHEMICAL- METALS& ALLOYS
Titanium & titaniumAlloy
C DC-179/00/01/01/2019:2019
0.001 % to 0.017 %
83 CHEMICAL- METALS& ALLOYS
Titanium & titaniumAlloy
Cr DC-179/00/01/01/2019:2019
0.0005 % to 2.20 %
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name TESTING AND EVALUATION LABORATORY, INSTITUTE FOR AUTOPARTS ANDHAND TOOLS TECHNOLOGY, A9, PHASE V, FOCAL POINT, LUDHIANA, PUNJAB ,INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number TC-5628 Page No. : 6 / 23
Validity 12/07/2019 to 11/07/2021 Last Amended on -
S.No Discipline / Group Product / Material ofTest
Specific TestPerformed
Test MethodSpecificationagainst which testsare performed
Range of Testing/Limits of Detection
84 CHEMICAL- METALS& ALLOYS
Titanium & titaniumAlloy
Cu DC-179/00/01/01/2019:2019
0.0005 % to 2.5 %
85 CHEMICAL- METALS& ALLOYS
Titanium & titaniumAlloy
Fe DC-179/00/01/01/2019:2019
0.001 % to 2.00 %
86 CHEMICAL- METALS& ALLOYS
Titanium & titaniumAlloy
Mn DC-179/00/01/01/2019:2019
0.0005 % to 5.50 %
87 CHEMICAL- METALS& ALLOYS
Titanium & titaniumAlloy
Mo DC-179/00/01/2019:2019
0.001 % to 17.00 %
88 CHEMICAL- METALS& ALLOYS
Titanium & titaniumAlloy
Nb DC-179/00/01/01/2019:2019
0.01 % to 7.5 %
89 CHEMICAL- METALS& ALLOYS
Titanium & titaniumAlloy
Ni DC-179/00/01/01/2019:2019
0.005 % to 0.08 %
90 CHEMICAL- METALS& ALLOYS
Titanium & titaniumAlloy
Si DC-179/00/01/01/2019:2019
0.001 % to 0.75 %
91 CHEMICAL- METALS& ALLOYS
Titanium & titaniumAlloy
Sn DC-179/00/01/01/2019:2019
0.001 % to 12.00 %
92 CHEMICAL- METALS& ALLOYS
Titanium & titaniumAlloy
V DC-179/00/01/01/2019:2019
0.001 % to 4.5 %
93 CHEMICAL- METALS& ALLOYS
Titanium & titaniumAlloy
W DC-179/00/01/01/2019:2019
0.005 % to 1.00 %
94 CHEMICAL- METALS& ALLOYS
Titanium & titaniumAlloy
Zr DC-179/00/01/01/2019:2019
0.001 % to 5.5 %
95 CHEMICAL- METALS& ALLOYS
Tool Steel C dc-29/02/21/01/2017:2017
0.35 % to 2.2 %
96 CHEMICAL- METALS& ALLOYS
Tool Steel Co DC-29/02/21/02/2017:2017
0.01 % to 10.0 %
97 CHEMICAL- METALS& ALLOYS
Tool Steel Cr DC-29/02/21/02/2017:2017
0.10 % to 14.0 %
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name TESTING AND EVALUATION LABORATORY, INSTITUTE FOR AUTOPARTS ANDHAND TOOLS TECHNOLOGY, A9, PHASE V, FOCAL POINT, LUDHIANA, PUNJAB ,INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number TC-5628 Page No. : 7 / 23
Validity 12/07/2019 to 11/07/2021 Last Amended on -
S.No Discipline / Group Product / Material ofTest
Specific TestPerformed
Test MethodSpecificationagainst which testsare performed
Range of Testing/Limits of Detection
98 CHEMICAL- METALS& ALLOYS
Tool Steel Mn DC-29/02/21/02/2017:2017
0.10 % to 2.5 %
99 CHEMICAL- METALS& ALLOYS
Tool Steel Mo DC-29/02/21/02/2017:2017
0.02 % to 6.0 %
100 CHEMICAL- METALS& ALLOYS
Tool SteeL Ni DC-29/02/21/02/2017:2017
0.01 % to 2.0 %
101 CHEMICAL- METALS& ALLOYS
Tool Steel P DC-29/02/21/02/2017:2017
0.002 % to 0.30 %
102 CHEMICAL- METALS& ALLOYS
Tool Steel Si DC-29/02/21/01/2017:2017
0.10 % to 1.5 %
103 CHEMICAL- METALS& ALLOYS
Tool Steel V DC-29/02/21/02/2017:2017
0.01 % to 19.0 %
104 CHEMICAL- METALS& ALLOYS
Tool Steel W DC-29/02/21/02/2017:2017
0.01 % to 19.0 %
105 CHEMICAL- METALS& ALLOYS
Zinc & its Zinc Alloy Al DC-178/00/01/01/2019:2019
0.0001 % to 7.5 %
106 CHEMICAL- METALS& ALLOYS
Zinc & its Zinc Alloy Cd DC-178/00/01/01/2019:2019
0.00005 % to 0.65 %
107 CHEMICAL- METALS& ALLOYS
Zinc & its Zinc Alloy Cu DC-178/00/01/01/2019:2019
0.00005 % to 15.00 %
108 CHEMICAL- METALS& ALLOYS
Zinc & its Zinc Alloy Fe DC-178/00/01/01/2019:2019
0.0003 % to 0.25 %
109 CHEMICAL- METALS& ALLOYS
Zinc & its Zinc Alloy Mg DC-178/00/01/01/2019:2019
0.00001 % to 10.00 %
110 CHEMICAL- METALS& ALLOYS
Zinc & its Zinc Alloy Mn DC-178/00/01/01/2019:2019
0.0001 % to 1.00 %
111 CHEMICAL- METALS& ALLOYS
Zinc & its Zinc Alloy Ni DC-178/00/01/01/2019:2019
0.0003 to 0.06
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name TESTING AND EVALUATION LABORATORY, INSTITUTE FOR AUTOPARTS ANDHAND TOOLS TECHNOLOGY, A9, PHASE V, FOCAL POINT, LUDHIANA, PUNJAB ,INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number TC-5628 Page No. : 8 / 23
Validity 12/07/2019 to 11/07/2021 Last Amended on -
S.No Discipline / Group Product / Material ofTest
Specific TestPerformed
Test MethodSpecificationagainst which testsare performed
Range of Testing/Limits of Detection
112 CHEMICAL- METALS& ALLOYS
Zinc & its Zinc Alloy Pb DC-178/00/01/01/2019:2019
0.0001 % to 3.00 %
113 CHEMICAL- METALS& ALLOYS
Zinc & its Zinc Alloy Sn DC-178/00/01/01/2019:2019
0.0003 % to 2.5 %
114 CHEMICAL- METALS& ALLOYS
Zinc & its Zinc Alloy Ti DC-178/00/01/01/2019:2019
0.002 % to 0.02 %
115 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Carbon steel forforgings
Blue fracture test IS 10138: 2017 Qualitative
116 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Carbon steel forforgings
Freedom from defects IS 1875: 2014 Qualitative
117 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Carbon steel forgings Dimension tolerance,mass per meter
IS 1875: 2014 10 mm to 450 mm
118 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Cold rolled steel strips Dimensions andtolerances
IS 5872: 2015 5 mm to 450 mm
119 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Combination SideCutting Plier
Bend test IS 3650: 2016 Qualitative
120 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Combination SideCutting Plier
Cutting Test IS 2615: 2013 Qualitative
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name TESTING AND EVALUATION LABORATORY, INSTITUTE FOR AUTOPARTS ANDHAND TOOLS TECHNOLOGY, A9, PHASE V, FOCAL POINT, LUDHIANA, PUNJAB ,INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number TC-5628 Page No. : 9 / 23
Validity 12/07/2019 to 11/07/2021 Last Amended on -
S.No Discipline / Group Product / Material ofTest
Specific TestPerformed
Test MethodSpecificationagainst which testsare performed
Range of Testing/Limits of Detection
121 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Combination SideCutting Plier
Dimension IS 3650: 2016 2 mm to 450 mm
122 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Combination SideCutting Plier
Handle Load test IS 2615: 2013 Qualitative
123 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Combination SideCutting Plier
Insulation test IS 2615: 2013 Qualitative
124 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Combination SideCutting Plier
Shock Test IS 2615: 2013 Qualitative
125 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Combination SideCutting Plier
Torsion Test IS 2615: 2013 4 Nm to 15.8 Nm
126 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Combination SideCutting Plier
Tube gripping test IS 2615: 2013 Qualitative
127 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Ferrous Material , Alloy& Products (Steel ,Stainless Steel ,Castiron)
% Elongation IS 1608: 2018 1 KN to 1900 KN
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name TESTING AND EVALUATION LABORATORY, INSTITUTE FOR AUTOPARTS ANDHAND TOOLS TECHNOLOGY, A9, PHASE V, FOCAL POINT, LUDHIANA, PUNJAB ,INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number TC-5628 Page No. : 10 / 23
Validity 12/07/2019 to 11/07/2021 Last Amended on -
S.No Discipline / Group Product / Material ofTest
Specific TestPerformed
Test MethodSpecificationagainst which testsare performed
Range of Testing/Limits of Detection
128 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Ferrous Material , Alloy& Products (Steel ,Stainless Steel ,Castiron)
% Reduction on area IS 1608: 2018 2 % to 78 %
129 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Ferrous Material , Alloy& Products (Steel ,Stainless Steel ,Castiron)
% Reduction on area ISO 6892-1: 2018 2 % to 78 %
130 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Ferrous Material , Alloy& Products (Steel ,Stainless Steel ,Castiron)
Bend Test IS 1599: 2012 Qualitative(MandrelSize :-50,60,80,100,120,160,180,200,240,300,320,360,400,480,40,45,55,65,70,85,90,75,95,108,112,128,135,145150,175,1,2,3,4,5,6,8,9,10,12,15,16,18,20,21,25 mmDiameter)
131 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Ferrous Material , Alloy& Products (Steel ,Stainless Steel ,Castiron)
Brinell Hardness Test IS 1500 ( Part - 1):2013
140 HBW (5/750) to450 HBW (5/750)
132 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Ferrous Material , Alloy& Products (Steel ,Stainless Steel ,Castiron)
Charpy Impact Test VNotch ( - 75 Degrees Cupto ambienttemperature)
IS 1757 ( Part-1 ): 2014 2 J to 300 J
133 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Ferrous Material , Alloy& Products (Steel ,Stainless Steel ,Castiron)
Charpy Impact U Notch IS 1499: 1977 2 J to 300 J
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name TESTING AND EVALUATION LABORATORY, INSTITUTE FOR AUTOPARTS ANDHAND TOOLS TECHNOLOGY, A9, PHASE V, FOCAL POINT, LUDHIANA, PUNJAB ,INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number TC-5628 Page No. : 11 / 23
Validity 12/07/2019 to 11/07/2021 Last Amended on -
S.No Discipline / Group Product / Material ofTest
Specific TestPerformed
Test MethodSpecificationagainst which testsare performed
Range of Testing/Limits of Detection
134 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Ferrous Material , Alloy& Products (Steel ,Stainless Steel ,Castiron)
Izod Impact test IS 1598 : 2015 2 J to 168 J
135 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Ferrous Material , Alloy& Products (Steel ,Stainless Steel ,Castiron)
Micro vicker hardnessTest
IS 1501 ( Part -1): 2013 90 HV 0.2 to 800 HV0.2
136 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Ferrous Material , Alloy& Products (Steel ,Stainless Steel ,Castiron)
Micro Vicker HardnessTester
IS 1501 ( Part -1): 2013 90 HV 0.1 to 450 HV0.1
137 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Ferrous Material , Alloy& Products (Steel ,Stainless Steel ,Castiron)
Rockwell hardnessTest (HRB)
IS 1586 ( Part - 1):2018
70 HRB to 100 HRB
138 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Ferrous Material , Alloy& Products (Steel ,Stainless Steel ,Castiron)
Rockwell Hardness test(HRC)
IS 1586 ( Part - 1 ):2018
20 HRC to 70 HRC
139 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Ferrous Material , Alloy& Products (Steel ,Stainless Steel ,Castiron)
Ultimate TensileStrength
IS 1608: 2018 1 KN to 1900 KN
140 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Ferrous Material , Alloy& Products (Steel ,Stainless Steel ,Castiron)
Vicker Hardness Test IS 1501 ( Part -1): 2013 100 HV 5 to 850 HV 5
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name TESTING AND EVALUATION LABORATORY, INSTITUTE FOR AUTOPARTS ANDHAND TOOLS TECHNOLOGY, A9, PHASE V, FOCAL POINT, LUDHIANA, PUNJAB ,INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number TC-5628 Page No. : 12 / 23
Validity 12/07/2019 to 11/07/2021 Last Amended on -
S.No Discipline / Group Product / Material ofTest
Specific TestPerformed
Test MethodSpecificationagainst which testsare performed
Range of Testing/Limits of Detection
141 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Ferrous Material , Alloy& Products (Steel ,Stainless Steel ,Castiron)
Yield Strength IS 1608: 2018 1 KN to 1900 KN
142 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Ferrous material ,Alloys& products
Vicker hardness test IS 1501 ( Part -1): 2013 180 HV 20 to 850 HV20
143 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Ferrous material Alloys& products (Steel,Stainless Steel)
Ericsen Cupping test IS 10175: 2012 0.2 mm to 4 mm
144 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Ferrous material, alloy& products
Micro Vicker HardnessTest
IS 1501 ( Part -1): 2013 90 HV 1 to 850 HV 1
145 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Ferrous material, alloysproducts
Micro Vicker hardnesstest
IS 1501 ( Part -1): 2013 90 HV 0.3 to 800 HV0.3
146 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Ferrous material, alloysproducts
Micro Vicker HardnessTest
IS 1501 ( Part -1): 2013 90 HV 0.5 to 800 HV0.5
147 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Ferrous material, alloys& products
Vicker hardness test IS 1501 ( Part -1): 2013 150 HV 10 to 850 HV10
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name TESTING AND EVALUATION LABORATORY, INSTITUTE FOR AUTOPARTS ANDHAND TOOLS TECHNOLOGY, A9, PHASE V, FOCAL POINT, LUDHIANA, PUNJAB ,INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number TC-5628 Page No. : 13 / 23
Validity 12/07/2019 to 11/07/2021 Last Amended on -
S.No Discipline / Group Product / Material ofTest
Specific TestPerformed
Test MethodSpecificationagainst which testsare performed
Range of Testing/Limits of Detection
148 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Ferrous materials,alloys & products
Brinell Hardness test IS 1500 (Part - 1): 2013 140 HBW (10/3000) to450 HBW (10/3000)
149 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Ferrous materials,alloys & products
Vicker hardness test IS 1501 ( Part -1): 2013 150 HV 50 to 850 HV50
150 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Ferrousmaterials,alloys &products
Vicker hardness test IS 1501 ( Part -1): 2013 200 HV 30 to 850 HV30
151 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Hand operated squaredrive socket wrenchand driving square forhand socket wrencheswith attachment
Dimension IS 7214: 2013 2 mm to 450 mm
152 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Hand operated squaredrive socket wrenchand driving square forhand socket wrencheswith attachment
Torque Testing IS 6131: 2013 4 Nm to 2000 Nm
153 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Hand operated squaredrive socket wrenchand driving square forhand socket wrencheswith attachment
Workmanship & Finish IS 6131: 2013 Qualitative(Qualitative)
154 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Hot Roll Steel plate Dimension & tolerance IS 6240: 2013 5 mm to 450 mm
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name TESTING AND EVALUATION LABORATORY, INSTITUTE FOR AUTOPARTS ANDHAND TOOLS TECHNOLOGY, A9, PHASE V, FOCAL POINT, LUDHIANA, PUNJAB ,INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number TC-5628 Page No. : 14 / 23
Validity 12/07/2019 to 11/07/2021 Last Amended on -
S.No Discipline / Group Product / Material ofTest
Specific TestPerformed
Test MethodSpecificationagainst which testsare performed
Range of Testing/Limits of Detection
155 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Hot Roll Steel Plate Strain ageembrittlement test
IS 6240: 2013 Qualitative(Qualitative)
156 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Hot rolled bars forproduction of brightbars
Adhesion test by knife IS 2629: 2016 Qualitative
157 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Hot rolled bars for theproduction of brightbars
Dimensions &tolerance
IS 7283: 2017 10 mm to 450 mm
158 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Hot rolled bars of brightbars
Freedom from defects IS 7283: 2017 Qualitative
159 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Hot Rolled medium andhigh tensile StructuralSteel
Dimension IS 2062: 2016 2 mm to 450 mm
160 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Multi slip joint Plier Dimensions IS 6118: 2016 2 mm to 500 mm
161 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Multi slip joint Plier Handle load test IS 6118: 2016 400 N to 1250 N
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name TESTING AND EVALUATION LABORATORY, INSTITUTE FOR AUTOPARTS ANDHAND TOOLS TECHNOLOGY, A9, PHASE V, FOCAL POINT, LUDHIANA, PUNJAB ,INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number TC-5628 Page No. : 15 / 23
Validity 12/07/2019 to 11/07/2021 Last Amended on -
S.No Discipline / Group Product / Material ofTest
Specific TestPerformed
Test MethodSpecificationagainst which testsare performed
Range of Testing/Limits of Detection
162 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Multi slip joint Plier Permanent set test IS 6118: 2016 1 mm to 4 mm
163 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Open jaw wrenches Dimensions IS 2028: 2004 2 mm to 450 mm
164 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Open jaw wrenches Torque testing IS 6131: 2013 4 Nm to 2000 Nm
165 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Open jaw wrenches Workmanship & finish IS 6131: 2013 Qualitative(Qualitative)
166 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Reinforced bar Dimension IS 1786: 2013 8 mm to 32 mm
167 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Reinforced Bar Mass per meter IS 1786: 2013 0.02 Kg to 10 Kg
168 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Reinforced bar Re Bend Test IS 1786 : 2013 Qualitative( Range 8mm to 32 mm)
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name TESTING AND EVALUATION LABORATORY, INSTITUTE FOR AUTOPARTS ANDHAND TOOLS TECHNOLOGY, A9, PHASE V, FOCAL POINT, LUDHIANA, PUNJAB ,INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number TC-5628 Page No. : 16 / 23
Validity 12/07/2019 to 11/07/2021 Last Amended on -
S.No Discipline / Group Product / Material ofTest
Specific TestPerformed
Test MethodSpecificationagainst which testsare performed
Range of Testing/Limits of Detection
169 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Ring Spanner Dimension IS 2029: 2013 2 mm to 450 mm
170 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Ring Spanner Torque testing IS 6131: 2013 4 Nm to 2000 Nm
171 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Ring Spanner Workmanship & Finish IS 6131: 2013 Qualitative(Qualitative)
172 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Single ended open jawwrenches
Dimensions IS 6149: 2016 2 mm to 450 mm
173 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Single ended open jawwrenches
Longitudinal Play IS 6149: 2016 Qualitative(Qualitative)
174 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Single ended open jawwrenches
Torque testing IS 6149: 2016 4 Nm to 2000 Nm
175 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Single ended open jawwrenches
Transverse Play IS 6149: 2016 Qualitative(Qualitative)
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name TESTING AND EVALUATION LABORATORY, INSTITUTE FOR AUTOPARTS ANDHAND TOOLS TECHNOLOGY, A9, PHASE V, FOCAL POINT, LUDHIANA, PUNJAB ,INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number TC-5628 Page No. : 17 / 23
Validity 12/07/2019 to 11/07/2021 Last Amended on -
S.No Discipline / Group Product / Material ofTest
Specific TestPerformed
Test MethodSpecificationagainst which testsare performed
Range of Testing/Limits of Detection
176 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Single ended open jawwrenches
Workmanship & finish IS 6149: 2016 Qualitative(Qualitative)
177 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel for hardening &tempering
Freedom from defects IS 5517: 2014 Qualitative(Qualitative)
178 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel for hardening &tempering
Hardenability test IS 3848: 2014 Qualitative(Qualitative)
179 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel for hardening andtempering
Dimensions IS 5517: 2014 10 mm to 450 mm
180 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Structural Steel Mass per meter IS 2062: 2016 0.02 Kg to 10 Kg
181 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Structural Steel Y-groove Crack abilityTest
IS 10842: 2011 Qualitative(Qualitative)
182 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Sub assembly/ancillaries/accessories : threadedfasteners (Bolt ,Screw)
Proof Load Bolts IS 1367 ( Part - 3 ):2017
1 KN to 1900 KN
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name TESTING AND EVALUATION LABORATORY, INSTITUTE FOR AUTOPARTS ANDHAND TOOLS TECHNOLOGY, A9, PHASE V, FOCAL POINT, LUDHIANA, PUNJAB ,INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number TC-5628 Page No. : 18 / 23
Validity 12/07/2019 to 11/07/2021 Last Amended on -
S.No Discipline / Group Product / Material ofTest
Specific TestPerformed
Test MethodSpecificationagainst which testsare performed
Range of Testing/Limits of Detection
183 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Sub assembly/ancillaries/accessories : threadedfasteners (Bolt ,Screw)
Proof load of nut IS 1367 ( Part - 6 ):2015
1 KN to 1900 KN
184 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Sub assembly/ancillaries/accessories : threadedfasteners (Bolt ,Screw)
Wedge tensile load IS 1367 ( Part - 3 ):2017
1 KN to 1900 KN
185 MECHANICAL-METALLOGRAPHYTEST
Ferrous material ,alloys& products
Depth ofDecarburization bymicroscopic &hardness method
IS 6396: 2000(RA2018)
5 micron to 800 micron
186 MECHANICAL-METALLOGRAPHYTEST
Ferrous material ,alloys& products
Designation of graphiteform ,Size &distribution byComparision methodGrey iron ,Cast iron &SGI iron
IS 7754: 1975. (RA2018)
Qualitative(Range100X)
187 MECHANICAL-METALLOGRAPHYTEST
Ferrous material ,alloys& products
Determination of casedepth of steel bymicroscopic &Hardness method
IS 6416: 1988( RA2018)
100 micron to 5000micron
188 MECHANICAL-METALLOGRAPHYTEST
Ferrous material ,alloys& products
Estimation of AverageGrain size bycomparision method
ASTM E 112 : 2013 Qualitative(ASTM No.1.0-10.0 At 100x)
189 MECHANICAL-METALLOGRAPHYTEST
Ferrous material ,alloys& products
Estimation of AverageGrain size bycomparision method
IS 4748 : 2009 Qualitative(ASTM No.1.0-10.0 At 100x)
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name TESTING AND EVALUATION LABORATORY, INSTITUTE FOR AUTOPARTS ANDHAND TOOLS TECHNOLOGY, A9, PHASE V, FOCAL POINT, LUDHIANA, PUNJAB ,INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number TC-5628 Page No. : 19 / 23
Validity 12/07/2019 to 11/07/2021 Last Amended on -
S.No Discipline / Group Product / Material ofTest
Specific TestPerformed
Test MethodSpecificationagainst which testsare performed
Range of Testing/Limits of Detection
190 MECHANICAL-METALLOGRAPHYTEST
Ferrous material ,alloys& products
Examination of microstructure (Greyiron,cast iron,melleable iron, SGIiron,low alloy steel,Case hardening steel ,Carbon tool steel)
ASM handbook Volume-9 Edition 2004: 2004
Qualitative(50X ,100X,200X 500X , 1000X)
191 MECHANICAL-METALLOGRAPHYTEST
Ferrous material ,alloys& products
Examination of microstructure (Greyiron,cast iron,melleable iron, SGIiron,low alloy steel,Case hardening steel ,Carbon tool steel)
ASM handbook Volume-9 Edition 1995: 1995
Qualitative(50X ,100X,200X 500X , 1000X)
192 MECHANICAL-METALLOGRAPHYTEST
Ferrous material ,alloys& products
Macroetch test ASTM E 381 : 2017 Qualitative(Plate I ,II, &III Visual & 10X)
193 MECHANICAL-METALLOGRAPHYTEST
Ferrous material ,alloys& products
Macroetch test IS 11371 (RA 2003):1985
Qualitative(Plate I ,II, &III Visual & 10X)
194 MECHANICAL-METALLOGRAPHYTEST
Ferrous material ,alloys& products
Measurement ofcoating thickness bymicroscopic thicknessby microscopic method
IS 3203: 1997( RA2018)
10 micron to 1000micron
195 MECHANICAL-METALLOGRAPHYTEST
Ferrous material ,alloys& products
Measurement ofcoating thickness bymicroscopic thicknessby microscopic method
IS 3203: 2016 10 micron to 1000micron
196 MECHANICAL-METALLOGRAPHYTEST
Ferrous material ,alloys& products
Non metallic Inclusionrating by Method 'A'
IS 4163 : 2004 0.5 to 3.0
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name TESTING AND EVALUATION LABORATORY, INSTITUTE FOR AUTOPARTS ANDHAND TOOLS TECHNOLOGY, A9, PHASE V, FOCAL POINT, LUDHIANA, PUNJAB ,INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number TC-5628 Page No. : 20 / 23
Validity 12/07/2019 to 11/07/2021 Last Amended on -
S.No Discipline / Group Product / Material ofTest
Specific TestPerformed
Test MethodSpecificationagainst which testsare performed
Range of Testing/Limits of Detection
197 MECHANICAL-METALLOGRAPHYTEST
Ferrous material ,alloys& products
Non metallic Inclusionrating by Method 'A'
ISO 4967: 2013 0.5 to 3.0
198 MECHANICAL-METALLOGRAPHYTEST
Ferrous materials,alloys & products
Non metallic Inclusionrating by Method 'A'
ASTM E 45: 2018 0.5 to 3.0
199 NON-DESTRUCTIVE-METALS & ALLOYS
Ferro magneticmaterial pipes & tubes
Magnetic ParticleTesting
IS 6752: 2014 Qualitative(Up to 3mmDepth)
200 NON-DESTRUCTIVE-METALS & ALLOYS
Metal & alloys Liquid penetrantTesting
EN 10228 :1999 ,ASME section V Article6 2019 , ASTM E 165/165M-2012 ,IS 3658:2010 : 2019
Qualitative(Flaw opento the surface)
201 NON-DESTRUCTIVE-METALS & ALLOYS
Metals & Alloys Magnetic particleTesting
EN 10228 -12016,ASTM E1444:2016 ASME SECV 2017 ART 7, ART 25SE 709 IS 7743 :RA2011 IS 10138 :RA2017 IS 3703 :RA2004: 2016
Qualitative(Up to 3mmDepth)
202 NON-DESTRUCTIVE-METALS & ALLOYS
Metals & Alloys Radiography Testing ASME section V article2 2017ASME B 16.34:2017 , ASTM E 390Volume (1,2,3):2015,ASTM E 155: 2015 ,ASTM E 446: 2015 ,ASTM E 64 :2017 ,IS4853 :2013 , IS 1182:2014: 2017
Qualitative(Internal flawrecommended upto 40mm equivalentthickness of steel)
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name TESTING AND EVALUATION LABORATORY, INSTITUTE FOR AUTOPARTS ANDHAND TOOLS TECHNOLOGY, A9, PHASE V, FOCAL POINT, LUDHIANA, PUNJAB ,INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number TC-5628 Page No. : 21 / 23
Validity 12/07/2019 to 11/07/2021 Last Amended on -
S.No Discipline / Group Product / Material ofTest
Specific TestPerformed
Test MethodSpecificationagainst which testsare performed
Range of Testing/Limits of Detection
203 NON-DESTRUCTIVE-METALS & ALLOYS
Metals & Alloys Ultrasonic Testing ASME SEC V ART 5 ,ASME SEC V ART 23SB 548, SE 609, SA388, SA 213, SA 435,SA 577, SA 578, SE273ASTM E 114IS9565: 2017
Qualitative(Recommended Range of testingcasting 5 - 300 mmforging 5- 1000mmwelding 5 - 100mmplate 5 - 300 mm)
204 NON-DESTRUCTIVE-METALS & ALLOYS
Metals & Alloys Ultrasonic ThicknessGauging
ASME sec V Art 23 SE797: 2017
Qualitative(1 mm to199.9 mm thicknessFlat surface & = dia 50mm. LC= 0.1 mm)
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name TESTING AND EVALUATION LABORATORY, INSTITUTE FOR AUTOPARTS ANDHAND TOOLS TECHNOLOGY, A9, PHASE V, FOCAL POINT, LUDHIANA, PUNJAB ,INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number TC-5628 Page No. : 22 / 23
Validity 12/07/2019 to 11/07/2021 Last Amended on -
S.No Discipline / Group Product / Material ofTest
Specific TestPerformed
Test MethodSpecificationagainst which testsare performed
Range of Testing/Limits of Detection
Site Facility
1 NON-DESTRUCTIVE-METALS & ALLOYS
Ferro magneticmaterial pipes & tubes
Magnetic ParticleTesting
IS 6752: 2014 Qualitative(Up to 3mmDepth)
2 NON-DESTRUCTIVE-METALS & ALLOYS
Metal & alloys Liquid penetrantTesting
EN 10228 :1999 ,ASME section V Article6 2019 , ASTM E 165/165M-2012 ,IS 3658:2010 : 2019
Qualitative(Flaw opento the surface)
3 NON-DESTRUCTIVE-METALS & ALLOYS
Metals & Alloys Magnetic particleTesting
EN 10228 -12016,ASTM E1444:2016 ASME SECV 2017 ART 7, ART 25SE 709 IS 7743 :RA2011 IS 10138 :RA2017 IS 3703 :RA2004: 2016
Qualitative(Up to 3mmDepth)
4 NON-DESTRUCTIVE-METALS & ALLOYS
Metals & Alloys Ultrasonic Testing ASME SEC V ART 5 ,ASME SEC V ART 23SB 548, SE 609, SA388, SA 213, SA 435,SA 577, SA 578, SE273ASTM E 114IS9565: 2017
Qualitative(Recommended Range of testingcasting 5 - 300 mmforging 5- 1000mmwelding 5 - 100mmplate 5 - 300 mm)
5 NON-DESTRUCTIVE-METALS & ALLOYS
Metals & Alloys Ultrasonic ThicknessGauging
ASME sec V Art 23 SE797: 2017
Qualitative(1 mm to199.9 mm thicknessFlat surface & = dia 50mm. LC= 0.1 mm)
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name TESTING AND EVALUATION LABORATORY, INSTITUTE FOR AUTOPARTS ANDHAND TOOLS TECHNOLOGY, A9, PHASE V, FOCAL POINT, LUDHIANA, PUNJAB ,INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number TC-5628 Page No. : 23 / 23
Validity 12/07/2019 to 11/07/2021 Last Amended on -
DEPARTMENT OF METROLOGY AND CALIBRATIONLABORATORY, INSTITUTE FOR AUTOPARTS AND HAND
TOOLS TECHNOLOGYhas been assessed and accredited in accordance with the standard
ISO/IEC 17025:2017''General Requirements for the Competence of Testing &
Calibration Laboratories''for its facilities at
A9, PHASEV, FOCAL POINT, LUDHIANA, PUNJAB, INDIA
in the field of
CALIBRATIONCertificate Number: CC-2308
Issue Date: 07/08/2019 Valid Until: 06/08/2021
This certificate remains valid for the Scope of Accreditation as specified in the annexure subject to continuedsatisfactory compliance to the above standard & the relevant requirements of NABL.
(To see the scope of accreditation of this laboratory, you may also visit NABL website www.nabl-india.org)
Signed for and on behalf of NABL
Chief Executive Officer
S.No Discipline / Group Quantity Measured/Instrument
Range / Frequency * CalibrationMeasurementCapability(±)
Remarks
Permanent Facility
1 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Calipers(Vernier/Dial/Digital) L.C. 0.01/0.020mm
0 to 450 mm 17µm Using slip gauges
2 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Depth Gauge(Vernier/Dial/Digital)L.C. 0.01mm
0 to 300 mm 17µm Using Slip Gauges
3 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Dial Gauge (LeverType) L.C. 0.001mm &L.C. 0.010mm
0 to 10 mm 1.90 µm (L.C. 0.001mm)6.0 µm (L.C. 0.010mm)
Using ULM
4 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Dial Gauges (PlungerType) L.C. 0.001mm
0 to 10 mm 1.90 µm Using ULM
5 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
External MicrometersL.C. 0.001/0.010mm
0 to 100 mm 3.6 µm Using Slip Gauges
6 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Feeler Gauge 0 to 1 mm 2.1 µm Using ULM
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name DEPARTMENT OF METROLOGY AND CALIBRATION LABORATORY, INSTITUTEFOR AUTOPARTS AND HAND TOOLS TECHNOLOGY, A9, PHASEV, FOCAL POINT,LUDHIANA, PUNJAB , INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2308 Page No. : 1 / 4
Validity 07/08/2019 to 06/08/2021 Last Amended on -
S.No Discipline / Group Quantity Measured/Instrument
Range / Frequency * CalibrationMeasurementCapability(±)
Remarks
7 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Gauges Block Steel 0.5 to 100 mm 0.30 µm to 0.66 µm Using ComparatorBlock , Gauges Blocks
8 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Height gauges(Vernier/Dial/Digital)L.C. 0.01/0.020 mm
0 to 450 mm 18.1 µm Using slip Gauges
9 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Micrometer Setting Rod 0 to 75 mm 2.7 µm Using ULM
10 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Plain Plug Gauge 3 to 100 mm 3.0 µm Using ULM
11 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Plain Ring Gauge 20 to 100 mm 7.7 µm Using ULM
12 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Snap Gauges 5 to 100 mm 3.0 µm Using Slip Gauges
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name DEPARTMENT OF METROLOGY AND CALIBRATION LABORATORY, INSTITUTEFOR AUTOPARTS AND HAND TOOLS TECHNOLOGY, A9, PHASEV, FOCAL POINT,LUDHIANA, PUNJAB , INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2308 Page No. : 2 / 4
Validity 07/08/2019 to 06/08/2021 Last Amended on -
S.No Discipline / Group Quantity Measured/Instrument
Range / Frequency * CalibrationMeasurementCapability(±)
Remarks
13 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Thread Plug Gauge(Major Diameter &Effective Diameter)
5 to 100 mm 2.91 µm Using ULM ,Threadmeasuring Wires
14 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Thread Ring Gauge(Minor Diameter &Effective Diameter)
20 to 100 mm 5.90 µm Using ULM
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name DEPARTMENT OF METROLOGY AND CALIBRATION LABORATORY, INSTITUTEFOR AUTOPARTS AND HAND TOOLS TECHNOLOGY, A9, PHASEV, FOCAL POINT,LUDHIANA, PUNJAB , INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2308 Page No. : 3 / 4
Validity 07/08/2019 to 06/08/2021 Last Amended on -
S.No Discipline / Group Quantity Measured/Instrument
Range / Frequency * CalibrationMeasurementCapability(±)
Remarks
Site Facility
1 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Surface Plate (Grade0,1,2,3)
100 to 2500 mm 2.0 Sq.root(L+W)/125,L&W in mm
Using ElectronicLeveler
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name DEPARTMENT OF METROLOGY AND CALIBRATION LABORATORY, INSTITUTEFOR AUTOPARTS AND HAND TOOLS TECHNOLOGY, A9, PHASEV, FOCAL POINT,LUDHIANA, PUNJAB , INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2308 Page No. : 4 / 4
Validity 07/08/2019 to 06/08/2021 Last Amended on -