w,.LIFTING

TEREX

STINGER™3470BoomTruckCrane

FEATURES

·34,000 Ibs. (15422 kg)maximumlifting capacity

·80ft. (24.4m)maximumsheaveheight

.120 ft. (36.6 m) maximumsheaveheightwith 40 ft. (12.2 m) jib

· 70 ft. (21.3m) fully proportionalthree-sectiontelescopic"keel"boom

· Exclusivecolorcodedboomandloadcharts

· Easy-to-installoptional24-40ft.

(7.3-12.2m) jib, manbasketsor workplatformincreasejob capabilities

· Choiceof two configurations- behindcabwith either1800or 3600workareaandrearmount

· ElectronicLoadMomentIndicatorandanti-two-blockdevicestandard

, , /·2-speedplanetarywinchhas11,400lb.(5171kg) maximumlinepull,150/220fpm (46/67mpm)linespeed

· Externallylocatedplanetaryrotationdrive

for easyaccessibilityfor maintenance

· Dualcontrolstationswith directmechanicallycontrolledhydraulicsystem

· 67,gal. (340I) capacityhydraulictank

· TerexSupportPlusproductservice

simple, available andcost effective TM

Machinesshownmayhaveoptionalequipment.

STINGER3470 LOADRATINGS A CAUTION: Do~ot use this specification sheet as a load rating chart. The format..of data IS not consistent with the machine chart and may be subject to change.

LoadRatings(Pounds)for 3600Full CapacityWorkAreawithOutriggersExtendedandOptionalFrontStabilizer

450

Stowed Jib Deductions (Pounds)

360 260 230 200 175

General Notes1. The operator must read and understand the

Owner's Manual before operating this crane.

2. Positioning or operation of crane beyond areasshown on this chart is not intended or

approved except where specified in Owner'sManual.

loaded boom angles at specified boom

lengths give only an approximation of the

operating radius. The boom angle before

loading should be greater to account for

deflections. Do not exceed the operatingradius for rated loads.

4. Use rating of next longer boom for boom

lengths not shown. Use rating of next greaterradius for load radii not shown.

5. Boom must be fully retracted when jib is

erected before lowering below minimum angle.

Retracted jib has no lifting capacity below a

50° boom angle.

6. Use rating of next lower boom angle for boom

angles not shown on jib load rating chart.

7. Lifting off the main boom point while the

swing around jib is erected is not intended or

approved.

8. Do not lower boom into this area, as hydraulic

pressure will not allow raising the boom

without retracting boom first.

9. Crane load ratings on outriggers are based on

freely suspended loads with the machine

leveled and standing on a firm uniform

supporting surface. No attempt shall be made

to move a load horizontally on the ground in

any direction.

10.Practicalworkingloadsdependon supportingsurface.windandotherfactorsaffectingstabilitysuchas hazardoussurroundings.experienceof personnel,andproperhandling,mustall betakeninto accountby theoperator.

11.Themaximumloadwhichmaybetelescopedis limitedby hydraulicpressure.boomangle,andboomlubrication.It is safeto attempttotelescopeany loadwithin the limitsof the loadratingchart.

INFORMATION

1. Deductionsmust bemadefrom ratedloadsforstowedjib, optionalattachments.hooksandloadblocks(seedeductionchart).Weightsofslingsandotherloadhandlingdevicesshallbeconsidereda partof the load.

2. Craneloadratingswith outriggersarebasedon outriggersandstabilizersextendedandsetwith all loadremovedfrom thecarrierwheels

3. load ratingsdo notexceed85%oftippingload.

DEFINITIONS

1. Operatingradiusis thehorizontaldistancefrom theaxisof rotationto thecenterof theverticalhoistlineor loadhookwith loadsuspended.

2. loadedboomangleasshownin the loadRatingsChartis the includedanglebetweenthehorizontalandlongitudinalaxesof theboombaseafterlifting ratedloadatratedradius.

RangeDiagram(27' - 70' boom)

Areaof Operation

DO NOTOPERATE

IN THIS AREAWITHOUT FRONT

STABILIZER

/' DEPLOYED -"/

Q"

I \I \\

DeductionsfromRatedLoadsfor

HandlingDevices

OVERHAULBALL: 125Ibs.

-SEE NOTE 5

.!.o 0

o 5 101520253035404550556065707580859095100105

OPERATING RADIUS FROM CENTERLINE OF ROTATION - FEET

--

BOOM LENGTH

27 FT 34 FT 43 FT 52 FT 61 FT 70 FT

OPERATINGLOADED LOADED LOADED LOADED LOADED LOADEDRADIUS BOOM LOAD BOOM LOAD BOOM LOAD BOOM LOAD BOOM LOAD BOOM LOAD

(FT) ANGLE RATING ANGLE RATING ANGLE RATING ANGLE RATING ANGLE RATING ANGLE RATING(DEG) (LB) (DEG) (LB) (DEG) (LB) (DEG) (LB) (DEG) (LB) (DEG) (LB)

5 77 34,00010 66 21,100 71 17,100 75 16,000 78 15,70015 54 15,100 62 14,000 68 12,100 72 11,100 75 10,800 77 9,60020 39 11,100 51 10,100 61 9,100 66 8,600 71 8,200 73 7,30025 17 7,900 40 7,700 53 7,100 61 6,900 66 6,600 69 5,90030 23 6,500 44 6,100 54 5,600 60 5.300 64 4,90035 33 4,800 47 4,700 54 4,600 60 4,15040 16 3,500 38 4,100 48 3.900 55 3,55045 27 3,250 41 3,200 49 3,05050 NOTERATINGSABOVETHEHEAVYLINEARE 9 2,950 33 2,800 44 2,65055 BASEOONSTRUCTURALCOMPETENCEAND 23 2,500 37 2,350NOTONMACHINESTABILITY.60 29 1,90065 I 19 1,700

JIB CAPACITIES FOR ALL BOOM LENGTHSVERIFYOPERATIONALMODESETIlNGONMG585DISPLAYBEFORELIFTINGWITHJIB

LoadedBoomAngle 35° 40° 45° 50° 55° 60° 65° 70° 75° 80°Retracted24ft. Jib 700 825 1000 1150 1340 1600 1900 2300 3100 4160Extended40 ft. Jib 520 580 650 730 810 930 1080 1400 1810 2260

1 SHEAVELOADBLOCK 200Ibs.

2 SHEAVELOADBLOCK: 230Ibs.

AUXILIARYSHEAVE: 501bs.

130

125

120

115

110

100

95

90 ....85 :tl

IL80

....

75 a70 iii

:I:65 w

>60

:I:55 Cl)

50

45

40

35

30

25

20

15

10

WINCHDATA

A CAUTION

Overloadandanti-two-blocksystemsmustbe in goodoperatingconditionbeforeoperatingcrane.Referto OwnersManual.

Keepat least3 wrapsof loadlineondrumat all times.

Useonly9/16" diametercablewith 33,600lb. breakingstrengthon this machine.

MOUNTINGCONFIGURATIONS

36'6"

26' '" RETRACTED

27' 4" RETRACTED70' FULL EXTENSION

20 FT. FLATBED

168"

237" 75"

3470 Behind Cab (BT) MountingConfigurationGrossVehicleWeightRating 33,000Ibs.(14969 kg)FrontAxleWeightRating 12,000Ibs.(5443kg)RearAxleWeightRating 21,000Ibs.(9526kg)Wheelbase ...237in. (6020mm)Cabto Axle 168in.(4267mm)Afterframe 75in. (1905mm)Transmission Heavy-Duty(Neutrallock-uprequiredforautomatictransmission)

ElectricalSystem Heavy-Duty

Cooling System... Heavy-Duty

FrameSection Modulus 15.9 in' (261 cm')

RBM Per FrameRail 1,400,000in.lb. (16130m.kg)

12' 2"

23' 6" RETRACTED61' 6" FULL EXTENSION 3470RearMount(RM)MountingConfiguration**

GrossVehicleWeightRating 33,000Ibs.(14969kg)FrontAxleWeightRating 12,000Ibs.(5443kg)RearAxleWeightRating 21,000Ibs.(9526kg)Wheelbase .249in.(6325mm)Cabto Axle 167in.(4242mm)Afterframe 78in. (1981mm)Transmission Heavy-Duty(Neutrallock-uprequiredforautomatictransmission)

ElectricalSystem... .Heavy-Duty

Cooling System Heavy-Duty

FrameSectionModulus 20.0 in' (328 cm')RBM Per FrameRail 1,800,000in. lb. (20740 m. kg)

""May requirecounterweightor tandei)lrearaxle.Consultfactory.

Note:Somestandardfeaturesfor theoptionalmountingconfigurationswill vary.ConsultyourTerexCranesdealeror factoryfor chassisandmountingrequirements.

, i

1Pariline I 2Pariline I 3 Pariline 4 Pariline

.. ..BLOCK BLOCKONE TWOSHEAVE SHEAVELOAD LOADBLOCK BLOCK

Winch I Cable lift and lift and lift and lift andSupplied Speed Speed Speed Speed

StandardI

9/16" Diam. 9,600lb. 19,200Ib 28,800 lb. 34,000lb.

StationaryIWRCXXIP 94 fpm" 47 fpm" 32 fpm" 24fpm"

Winch 9/16" Diam. 6,720lb. 13,440lb. 20,160lb. 26,880lb.RotationResistant 94 fpm" 47 fpm" 32 fpm" 24fpm"

"First layerspeed. Forfourth layerspeed,multiply"valueby 1.33,for burstspeed,multiplyby 1.7.

BlockType RatingOverhaulBall 6.5 ton (5.9mt)1 SheaveBlock 17ton (15.4mt)

TEREXSTINGER3470BoomTruckCrane

SPECIFICATIONS

Boom70 ft. (21.3 m) three section full power mechanicallysynchronized boom. Patented keel boom design utilizesa keel-shaped baseplate combined with a deep, four plate boom sectionto optimizestrength / rigidity-to-weightratio. Exclusive,patented color-coded boom and load charts allowthe operator toeasily and quicklydetermine boom extension, boom angle andload capacity. Maximumsheave height with three section 70 ft.(21.3 m) boom is 80 ft. (24.4m). Maximumsheave height withoptional two-stage 40 ft. (12.2 m) jib is 120 ft. (36.6 m).

WinchHydraulicwinch with gear motor and planetary reduction gearingprovides 2-speed operation. First layer rope pull is 11,400 Ibs.(5171 kg). Wire rope size is 9/16" (14 mm) with 33,600 Ibs.(15 241 kg) breaking strength.

OperatingSpeedsMainframe/ turret assembly planetary rotation provides 180°rotation (370° with optional front bumper outrigger). Swingrotation is 40 seconds. Boom up/down is 22/22 seconds andboom extend/retract is 50/22 seconds.

HydraulicsThreesectionpumpallowsthe operatorto performsimultaneouscraneoperations(winch,boomandswing). Capacitiesare 36,20 and 11 gpm(136.3,75.7and 41.6Ipm). Combinedsystemcapacityis 67 gpm (253.6Ipm).

ControlsFullyproportional,excellentmeteringcharacteristicsfor preciseboommovements.Independentoutriggercontrolsallowsthecraneto bestableandlevelin rigorousworkingconditions.LoadMomentIndicatingSystemhasaudioalarmandfunctionalshutdownwhenoperatorencountersanoverloadsituation.

OutriggersWide-stancelink-typemainoutriggershavea 18 ft. 6 in.(5.6 m) pin-to-pinspreadwhenfully extended.A-Framerearoutriggershave10ft. 1 in. (3 m)tip-to-tipspan.

SubframeSingle fabricated, closed-box stylesubframeyieldsgreaterstrengthandrigidity. Wheelbasefor standardtruckcranemountingconfigurationis 237in. (6 m).

OPTIONSANDACCESSORIES

TerexStingeroffersa widerangeof optionsandaccessoriestocustomizeyour truckcraneto your exactneeds.

Theseinclude:

· Singleandtwo-stagejibs· Multi-partloadblocks· Auxiliarywinch· Spin-resistantloadline· Wood, steelor extraheavydutysteelflatbeds· Radio remote controls· One-man or two-man baskets

· Self-Ievelingworkplatformwithradioremote

Formoreinformation.productdemonstration,or detailson purchase,leaseandrentalplans,pleasecontactyour localTerexCranesdealer.

TCRO-104 @TerexCranes, Inc. 2001

· Winchdrum tensioner· Continuous rotation· Oilcooler

· Rear bumper· Single front bumper outrigger (required for 370°

or continuous rotation)

· Hydraulichose reel· Hydraulic auxiliary tool circuit

Wereservetheright to amendthesespecificationsat anytimewithoutnotice.Theonlywarrantyapplicableis ourstandardwrittenwarrantyapplicableto the particularproductandsale.Wemakeno otherwarranty,expressedor implied.

, I

~TEREX CRANES550 OldHighway56 ~Olathe,KS66061-4640USA Gw.terexlift.com(913)782-1200. FAX:(913)782-1625E-mail:inquire@terexlifting.com

Litho in U.S.A. 10J1201MSG