tenant improvement ve - amazon web services · 10. shower rods and curtains 11. dust collection and...

P 503.224.9560 F 503.228.1285 W MCKNZE.COM RiverEast Center, 1515 SE Water Avenue, #100, Portland, OR 97214ARCHITECTURE INTERIORS STRUCTURAL ENGINEERING CIVIL ENGINEERING LAND USE PLANNING TRANSPORTATION PLANNING LANDSCAPE ARCHITECTURE

Portland, Oregon Vancouver, Washington Seattle, Washington

H:\Projects\215031900\6_Final\ADD-1-Tenant Improvement VE-170623.docx

ADDENDUM NO. 1, June 23, 2017 RE: Yogi Tea – Tenant Improvement VE Project No. 2150319.03 FROM: Mackenzie

RiverEast Center PO Box 14310 Portland, OR 97293 1515 SE Water Avenue, Suite 100 Portland, OR 97214 (503) 224-9560

TO: Prospective Bidders

ADDENDUM NO. 1 amends the contract documents for the subject project, dated June 9, 2017. It is the responsibility of the prospective bidders to note the contents of this addendum and notify the Owner that this addendum has been received. Acknowledge receipt by inserting the number of this addendum in the space provided on the Bid Proposal Form.

The following changes in the contract documents constitute this addendum. All changes by addenda are to be included in the proposal form, and the contents of the addenda become a part of the Contract Documents for this project. All changes offset only the specified drawings, words, or paragraphs mentioned. The balance of the drawings and specifications will remain in full force.

This addendum includes the following:

▪ Professional Stamps and Signatures ▪ Changes to Specifications ▪ Product Substitutions ▪ Changes to Drawings

ADDENDUM NO. 1, June 23, 2017 Yogi Tea – Tenant Improvement VE Project Number 2150319.03


CHANGES TO SPECIFICATIONS

1. Section 01 10 00 – See attached.


3. Section 08 43 13 – Deleted section.

4. Section 08 46 00 – Deleted section.

5. Section 09 51 00 – Suspended acoustical Ceilings - Revise section 2.02 to read:

2.02 Acoustical Units

1. Acoustical Units – General: ASTM E1264, Class A.

2. VOC Content: As specified in 06 61 16.

3. Product: See Schedule on plans.

4. Substitutions: See Section 01 60 00 – Product Requirements.

6. Section 09 72 00 – Deleted Section.


8. Section 10 21 13.13 – Revise section 2.03.A to read:

A. Toilet Compartments: Powder-coated steel, ceiling hung.

9. Section 12 93 13 – Existing section; added section to Table of Contents.



PRODUCT SUBSTITUTIONS

The following product substitutions have been reviewed, with the disposition noted:

DIVISION PRODUCT DISPOSITION

07 41 13 Taylor Metal Products – MS-150 Accepted

ADDENDUM NO. 1, June 23, 2017 Yogi Tea – Tenant Improvement VE Project Number 2150319.03


CHANGES TO DRAWINGS

1. See attached change log and drawings referenced therein.

Yogi Tea - Tenant Improvement - Bid Set June 9, 2017

Job Number 2150319.00 Summary01 10 00 - 1/2

SECTION 01 10 00

SUMMARY

PART 1 GENERAL

1.01 PROJECT

A. Project Name: Yogi Tea - Tenant Improvement- VE Addendum 1

B. Owner's Name: GTO Property, LLC.

C. Architect's Name: Mackenzie.

D. The Project consists of the construction of Interior and exterior tenant improvements, includingmechanical, electrical and plumbing.

1.02 CONTRACT DESCRIPTION

A. Contract Type: A single prime contract based on a Stipulated Price as described in Document 00 52 00 -Agreement Form.

1.03 DESCRIPTION OF ALTERATIONS WORK

A. Scope of demolition and removal work is shown on drawings.

1.04 WORK BY OWNER

A. Owner will supply and install the following:1. Guardrail throughout warehouse walk paths.2. Installation and final mechanical and electrical connections of manufacturing equipment and

conveyors..3. Small appliances at break areas (microwaves, vending, etc.)..4. Office equipment (copiers, etc.).5. Office furniture not otherwise indicated in the plans.6. Dock protection/bollards throughout.7. Process-related steel guides and protection.8. Racking at warehouse and production areas.9. lockers10. shower rods and curtains11. Dust collection and baghouse12. Audio/Visual systems and components.13. OSHA Security/tie-off at second floor office.14. White boards or tack boards15. Trash/recycle stations at break rooms16. Dock lights and seals.17. Crash doors 154A, 154B, and 154C at IMA Room

B. Owner will supply the following for installation by Contractor:1. Forklift charging stations. GC to provide disconnect as shown on electrical..2. GC to remove, relocate and install two pairs of double-acting traffic doors from existing Yogi

facility. GC to procure and install residual double-acting traffic doors.. 2. 3.Low voltage data/security wiring installation by owner. GC to provide ring-and string at all

low-voltage outlets per electrical plans.. 3. 4.Lab casework. owner to provide and install all casework in labs. GC to provide plumbing and

electrical connections as indicated in the plans. 4. 5.Dock locks. GC to remove, relocate and install threepositions as described in plans.


Summary Job Number 2150319.0001 10 00 - 2/2

5. 6.Manufacturing equipment. GC to install distribution per M/E/P plans. Owner to install equipment,including final connections of all utilities.

6. 7.Demountable partitions at the main office. GC to provide electrical. mechanical and plumbingconnections per plans.

1.05 PERMITS:

A. THE OWNER WILL OBTAIN THE FOLLOWING PERMITS FOR THE PROJECT: 1. TENANT IMPROVEMENT PERMIT

1.06 OWNER OCCUPANCY

A. Owner intends to occupy the Project upon Substantial Completion.

B. Cooperate with Owner to minimize conflict and to facilitate Owner's operations.

C. Schedule the Work to accommodate Owner occupancy.

1.07 CONTRACTOR USE OF SITE AND PREMISES

A. Construction Operations: Limited to areas noted on Drawings.

B. Construction of tenant improvements will be concurrent with shell construction. The selected GC willneed to cooperate with the shell GC for coordination and installation of all work.

C. Arrange use of site and premises to allow:1. Owner occupancy.2. Work by Others.3. Work by Owner.

D. Provide access to and from site as required by law and by Owner:

E. Emergency Site Access and Building Exits During Construction: Keep all exits required by code openduring construction period; provide temporary exit signs if exit routes are temporarily altered.

F. Time Restrictions:1. Limit conduct of especially noisy exterior work to hours allowed by the jurisdiction..

1.08 WORK SEQUENCE

A. Coordinate construction schedule and operations with Owner.

B. Coordinate construction schedule and operations with Architect.

END OF SECTION


Job Number 2150319.00 OVERHEAD SECTIONAL DOORS08 36 13 - 1/5

SECTION 08 36 13

OVERHEAD SECTIONAL DOORS

PART 1 GENERAL

1.01 SECTION INCLUDES

A. Overhead sectional doors, manually and electrically operated.

B. Operating hardware and supports.

C. Electrical controls.

1.02 RELATED REQUIREMENTS

A. Section 07 90 05 - Joint Sealers: Sealing joints between frames and adjacent construction.

B. Section 26 05 33 - Conduit, Raceway Boxes and Fittings: Conduit from electric circuit to operator andfrom operator to control station.

1.03 REFERENCE STANDARDS

A. ASTM A653/A653M - Standard Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-IronAlloy-Coated (Galvannealed) by the Hot-Dip Process; 2015.

B. ASTM C1048 - Standard Specification for Heat-Strengthened and Fully Tempered Flat Glass; 2012.

C. ASTM E330/E330M - Standard Test Method for Structural Performance of Exterior Windows, Doors,Skylights and Curtain Walls by Uniform Static Air Pressure Difference; 2014.

D. DASMA 102 - American National Standard Specifications for Sectional Overhead Type Doors; 2011.

E. NEMA MG 1 - Motors and Generators; 2014.

F. NFPA 70 - National Electrical Code; Most Recent Edition Adopted by Authority Having Jurisdiction,Including All Applicable Amendments and Supplements.

G. UL 325 - Standard for Door, Drapery, Gate, Louver, and Window Operators and Systems; CurrentEdition, Including All Revisions.

1.04 SUBMITTALS

A. See Section 01 30 00 - Administrative Requirements, for submittal procedures.

B. Shop Drawings: Indicate opening dimensions and required tolerances, connection details, anchoragespacing, hardware locations, and installation details.

C. Product Data: Show component construction, anchorage method, and hardware.

D. Operation Data: Include normal operation, troubleshooting, and adjusting.

E. Maintenance Data: Include data for motor and transmission, shaft and gearing, lubrication frequency,spare part sources.

F. Warranty: Submit manufacturer warranty and ensure forms have been completed in Owner's nameand registered with manufacturer.

1.05 QUALITY ASSURANCE

A. Manufacturer Qualifications: Company specializing in manufacturing the products specified in thissection with minimum three years of documented experience.

B. Conform to applicable code for motor and motor control requirements.

C. Products Requiring Electrical Connection: Listed and classified by Underwriters Laboratories Inc., assuitable for the purpose specified.


OVERHEAD SECTIONAL DOORS Job Number 2150319.0008 36 13 - 2/5

1.06 WARRANTY

A. See Section 01 78 00 - Closeout Submittals for warranty requirements.

B. Correct defective Work within a five year period after Date of Substantial Completion.

PART 2 PRODUCTS

2.01 MANUFACTURERS

A. Sectional Doors - Basis of Design: Steel - Overhead Door Model 596; Aluminum - Overhead Door Model521 .422, insulated, for interior.

B. Other Acceptable Manufacturers:1. Clopay Corporation: www.clopaydoor.com.2. Wayne-Dalton, a Division of Overhead Door Corporation: www.wayne-dalton.com.3. Overhead Door Company; www.ohd.com.4. Substitutions: See Section 01 60 00 - Product Requirements.

2.02 STEEL DOOR COMPONENTS

A. Steel Doors: Flush steel, insulated; vertical lift operating style with track and hardware; complying withDASMA 102, Commercial application.1. Performance: Withstand positive and negative wind loads equal to 1.5 times design wind loads

specified by local code without damage or permanent set, when tested in accordance with ASTME330/E330M, using 10 second duration of maximum load.

2. Door Nominal Thickness: 2 inches thick.3. Exterior Finish: Factory primed; field finished as indicated in Section 09 91 13.4. Interior Finish: Factory finished with acrylic baked enamel; standard factory finish; color as

selected from manufacturers standard line.5. Glazed Lights: one glazed lights per panel, one row; set in place with resilient glazing channel as

indicated on plans.6. Operation: Electric._____.

a. Coordinate installation for interlock at Trash/Recycle area as indicated on plans

B. Door Panels: Steel construction; outer steel sheet of 20 gage, 0.0359 inch minimum thickness, flushprofile; inner steel sheet of 26 gage, 0.01875 inch minimum thickness, flat profile; core reinforcementsheet steel roll formed to channel shape, rabbeted weather joints at meeting rails; expandedpolystyrene (EPS) insulation.

C. Window Frame: Manufacturers standard, finish to match.

D. Glazing: Fully tempered glass; insulated; clear; 1 inch thick. 24" by 7"

E. Door Panels: Flush steel construction; 20 gage outer steel sheet , flat profile; 26 gage inner steel sheet,flat profile; core reinforcement of 16 gage sheet steel roll formed to channel shape, rabbeted weatherjoints at meeting rails; insulated.

2.03 ALUMINUM DOOR COMPONENTS

A. Aluminum Doors: Stile and rail aluminum with glazed panels; standard lift operating style with trackand hardware ; complying with DASMA 102, Commercial application.1. Door Nominal Thickness: 3 inches thick.2. Finish: Factory anodized; clear anodized.3. Glazed Lights: 5 glazed lights per panel, All rows; set in place with resilient glazing channel.4. Operation: Electric.

B. Glazing: Fully tempered glass; insulated; clear; 1/2 inch thick.

http://global.ihs.com/doc_detail.cfm?rid=BSD&document_name=ASTM%20E330/E330M



























M. Job Number 2150319.00 OVERHEAD SECTIONAL DOORS 08 36 13 - 3/5

2.03 2.04DOOR COMPONENTS

A. Track: Rolled galvanized steel, 0.090 inch minimum thickness; 3 inch wide at Steel doors, 2" wide ataluminum doors, continuous one piece per side; galvanized steel mounting brackets 1/4 inch thick.

B. Hinge and Roller Assemblies: Heavy duty hinges and adjustable roller holders of galvanized steel;floating hardened steel bearing rollers, located at top and bottom of each panel, each side.

C. Lift Mechanism: Torsion spring on cross head shaft, with braided galvanized steel lifting cables.

D. Sill Weatherstripping: Resilient hollow rubber strip, one piece; fitted to bottom of door panel, fulllength contact.

E. Jamb Weatherstripping: Roll formed steel section full height of jamb, fitted with brushweatherstripping, placed in moderate contact with door panels.

F. Head Weatherstripping: brush weatherstripping, one piece full length.

G. Panel Joint Weatherstripping: Neoprene foam seal, one piece full length.

H. Lock: Inside side mounted, adjustable keeper, spring activated latch bar with feature to retain in lockedor retracted position; interior and exterior handle.

2.04 2.05MATERIALS

A. Sheet Steel: Hot-dipped galvanized steel sheet, ASTM A653/A653M, with G60/Z180 coating, plainsurface.

B. Float Glass: Provide float glass glazing, unless noted otherwise.1. Heat-Strengthened and Fully Tempered Types: ASTM C1048.

C. Insulation: Foamed-in-place polyurethane.Expanded polystyrene (EPS).1. R-value of 17.40. 7.35. U-Value of 0.05713

D. Metal Primer Paint: Zinc molybdate type.

2.05 2.06ELECTRICAL OPERATION

A. Operator, Controls, Actuators, and Safeties: Comply with UL 325; provide products listed by a testingagency acceptable to authorities having jurisdiction.

B. Electric Operators:1. Mounting: Side mounted on cross head shaft .2. Motor Enclosure:

a. Exterior doors: NEMA MG 1 Type 4; open drip proof.b. Interior doors: NEMA MG 1 Type 1; TEFC.

3. Motor Rating: 3/4 hp; continuous duty.4. Motor Voltage: 277 volt, single phase, 60 Hz.5. Motor Controller: NEMA ICS 2, full voltage, reversing magnetic motor starter.6. Controller Enclosure: NEMA 250 Type 1.7. Brake: Adjustable friction clutch type, activated by motor controller.8. Manual override in case of power failure.

C. Electrical Characteristics:1. Provide UL LIsted electric operator, size and type as recommended by manufacturer to move door

in either direction at not less than 2/3 foot nor more than 1 foot per second. Operator shall meetUL325(latest edition) requirements for continuous monitoring of safety devices.

D. Motor: NEMA MG 1, Type 1.

E. Wiring Terminations: Provide terminal lugs to match branch circuit conductor quantities, sizes, andmaterials indicated. Enclose terminal lugs in terminal box sized to NFPA 70.
















































OVERHEAD SECTIONAL DOORS Job Number 2150319.0008 36 13 - 4/5

F. Disconnect Switch: Factory mount disconnect switch in control panel.

G. Electric Operator: Side mounted on cross head shaft, adjustable safety friction clutch; brake systemactuated by independent voltage solenoid controlled by motor starter; enclosed gear driven limitswitch; enclosed magnetic cross line reversing starter; mounting brackets and hardware.

H. Safety Edge: At bottom of door panel, full width; electro-mechanical sensitized type, wired to stop doorupon striking object; hollow neoprene covered to provide weatherstrip seal.1. Products:

a. Miller Edge, Inc: www.MillerEdge.com.b. Substitutions: See Section 01 60 00 - Product Requirements.

I. Control Station, steel doors: Standard three button (open-close-stop) continuous pressure type controlfor each electric operator.1. 24 volt circuit.2. Surface mounted.3. Locate at inside door jamb.

J. Interconnection: interconnect controls at Trash/Recycle area to prevent anyt exterior and interiordoors from being open simultaneously (sally port configuration). Multiple exterior doors may operatesimultaneously so long as no interior doors can be opened and vice versa.

K. Hand Held Transmitter at aluminum doors: Digital control, resettable.

PART 3 EXECUTION

3.01 EXAMINATION

A. Verify that wall openings are ready to receive work and opening dimensions and tolerances are withinspecified limits.

B. Verify that electric power is available and of the correct characteristics.

3.02 PREPARATION

A. Clean surfaces thoroughly prior to installation.

B. Prepare surfaces using the methods recommended by the manufacturer for achieving the best result forthe substrate under the project conditions.

3.03 INSTALLATION

A. Install door unit assembly in accordance with manufacturer's instructions.

B. Anchor assembly to wall construction and building framing without distortion or stress.

C. Securely brace door tracks suspended from structure. Secure tracks to structural members only.

D. Fit and align door assembly including hardware.

E. Coordinate installation of electrical service. Complete power and control wiring from disconnect to unitcomponents.

3.04 TOLERANCES

A. Maximum Variation from Plumb: 1/16 inch.

B. Maximum Variation from Level: 1/16 inch.

C. Longitudinal or Diagonal Warp: Plus or minus 1/8 inch from 10 ft straight edge.

D. Maintain dimensional tolerances and alignment with adjacent work.












































M. Job Number 2150319.00 OVERHEAD SECTIONAL DOORS 08 36 13 - 5/5

3.05 ADJUSTING

A. Adjust door assembly for smooth operation and full contact with weatherstripping.

3.06 CLEANING

A. Clean doors and frames and glazing.

B. Remove temporary labels and visible markings.

3.07 PROTECTION

A. Protect installed products from damage until Date of Substantial Completion.

B. Do not permit construction traffic through overhead door openings after adjustment and cleaning.

END OF SECTION














Job Number 2150319.00 TOILET ACCESSORIES10 28 00 - 1/4

SECTION 10 28 00

TOILET ACCESSORIES

PART 1 GENERAL

1.01 SECTION INCLUDES

A. Accessories for toilet rooms and utility rooms.

B. Electric hand/hair dryers.

C. Utility room accessories.

D. B.Grab bars.

1.02 REFERENCE STANDARDS

A. 36 CFR 1191 - Americans with Disabilities Act (ADA) Accessibility Guidelines for Buildings and Facilities;Architectural Barriers Act (ABA) Accessibility Guidelines; current edition.

B. ASTM A269/A269M - Standard Specification for Seamless and Welded Austenitic Stainless SteelTubing for General Service; 2015.

C. ASTM A666 - Standard Specification for Annealed or Cold-Worked Austenitic Stainless Steel Sheet,Strip, Plate, and Flat Bar; 2015.

D. ASTM B456 - Standard Specification for Electrodeposited Coatings of Copper Plus Nickel PlusChromium and Nickel Plus Chromium; 2011.

E. ASTM C1036 - Standard Specification for Flat Glass; 2011.

F. ASTM C1503 - Standard Specification for Silvered Flat Glass Mirror; 2008 (Reapproved 2013).

1.03 ADMINISTRATIVE REQUIREMENTS

A. Coordinate the work with the placement of internal wall reinforcement to receive anchor attachments.

1.04 SUBMITTALS

A. See Section 01 30 00 - Administrative Requirements, for submittal procedures.

B. Product Data: Submit data on accessories describing size, finish, details of function, and attachmentmethods.

C. Manufacturer's Installation Instructions: Indicate special procedures and conditions requiring specialattention.

PART 2 PRODUCTS

2.01 MANUFACTURERS

A. Toilet Accessories:1. ASI - American Specialties, Inc: www.americanspecialties.com.2. Bradley Corporation: www.bradleycorp.com.3. Georgia-Pacific Professional ; _____: www.blue-connect.com.4. Bobrick: www.bobrick.com.5. Substitutions: Section 01 60 00 - Product Requirements.

B. Electric Hand/Hair Dryers:1. American Dryer, Inc : www.americandryer.com.2. Excel Dryer : www.exceldryer.com/#sle.3. World Dryer Corporation ; _____: www.worlddryer.com.4. Substitutions: Section 01 60 00 - Product Requirements.


TOILET ACCESSORIES Job Number 2150319.0010 28 00 - 2/4

C. All items of each type to be made by the same manufacturer.

2.02 MATERIALS

A. Accessories - General: Shop assembled, free of dents and scratches and packaged complete withanchors and fittings, steel anchor plates, adapters, and anchor components for installation.

B. Stainless Steel Sheet: ASTM A666 , Type 304.

C. Stainless Steel Tubing: ASTM A269/A269M, Grade TP304 or TP316.

D. Mirror Glass: Annealed float glass, ASTM C1036 Type I, Class 1, Quality Q2, with silvering, protectiveand physical characteristics complying with ASTM C1503.

E. Adhesive: Two component epoxy type, waterproof.

F. Fasteners, Screws, and Bolts: Hot dip galvanized ; tamper-proof ; security type.

G. Expansion Shields: Fiber, lead, or rubber as recommended by accessory manufacturer for componentand substrate.

2.03 2.02FINISHES

A. Stainless Steel: No. 4 Brushed finish, unless otherwise noted.

B. Chrome/Nickel Plating: ASTM B456 , SC 2, polished finish , unless otherwise noted.

C. Baked Enamel: Pretreat to clean condition, apply one coat primer and minimum two coats epoxybaked enamel.

2.04 2.03TOILET ROOM ACCESSORIES

A. Toilet Paper Dispenser: Single roll, surface mounted bracket type, chrome-plated zinc alloy brackets ,spindleless type for tension spring delivery designed to prevent theft of tissue roll.

A. Toilet Paper Dispenser: Double roll, semi-recessed, stainless steel unit with pivot hinge , tumblerlock.1. Products:

a. Bobrick B-6977.b. Substitutions: Section 01 60 00 - Product Requirements.

B. Electric Dryers: Traditional fan-in-case type, with downward nozzle.1. Cover: White plastic.

C. B.Combination Towel Dispenser/Waste Receptacle: Recessed flush with wall, stainless steel; seamlesswall flanges, continuous piano hinges, tumbler locks on upper and lower doors.1. Towel dispenser capacity: 400 C-fold.2. Waste receptacle capacity: 4 gallons.3. Products:


C. Soap Dispenser: Liquid soap dispenser, wall-mounted, surface, with stainless steel cover andhorizontal stainless steel tank and working parts; push type soap valve, check valve, and window gagerefill indicator .

D. Soap Dispenser: Top-filling, counter-m foaming soap dispenser. Vandal-resistant locking cover andspout. Bright-polished spout, cover and escutcheon. High-imapct ABS body and shank.Shatter-resistant polyethelyne container, 34- fl. oz.1. Products:

a. Bobrick 823b. Substitutions: Section 011 60 00 - Product Requirements.


M. Job Number 2150319.00 TOILET ACCESSORIES10 28 00 - 3/4

E. Mirrors: Stainless steel framed, 1/4 inch thick annealed float glass; ASTM C1036.1. Annealed Float Glass: Silvering, protective and physical characteristics in compliance with ASTM

C1503.2. Size: 24" x 36".3. Frame: 0.05 inch angle shapes, with mitered and welded and ground corners , and tamperproof

hanging system; satin finish.4. Backing: Full-mirror sized, minimum 0.03 inch galvanized steel sheet and nonabsorptive filler

material.

F. Seat Cover Dispenser: Stainless steel, recessed, reloading by concealed opening at base , tumblerlock.1. Minimum capacity: 500 seat covers .2. Products:


G. D.Grab Bars: Stainless steel, nonslip grasping surface finish.1. Standard Duty Grab Bars:

a. Push/Pull Point Load: 250 pound-force, minimum.b. Dimensions: 1-1/4 inch outside diameter, minimum 0.05 inch wall thickness, exposed flange

mounting, 1-1/2 inch clearance between wall and inside of grab bar.c. Length and Configuration: As indicated on drawings.d. Products:

1) Bobrick B5806 (length per plan).2) Substitutions: Section 01 60 00 - Product Requirements.

H. Purse Shelf: Fold-down, with spring-loaded hinge designed to automatically return shelf to verticalposition when not in use; 0.03 inch satin-finished stainless steel, with 1/4 inch rolled or 1/2 inchchannel edge at shelf front.1. Products:

a. __________.b. Substitutions: Section 01 60 00 - Product Requirements.

I. Sanitary Napkin Disposal Unit: Stainless steel, Partition-mounted, self-closing door, locking bottompanel with full-length stainless steel piano-type hinge, removable receptacle.1. Products:


2.05 ELECTRIC HAND/HAIR DRYERS

A. Electric Hand Dryers: Traditional fan-in-case type, with downward fixed nozzle.1. Operation: Automatic, sensor-operated on and off.2. Mounting: Surface mounted.3. Cover: Stainless steel with brushed finish.

a. Tamper-resistant screw attachment of cover to mounting plate.b. Screened or shielded air intake.c. Screen or shield to prevent access to motor/heater.

4. Air Velocity: 15,000 linear feet per minute, minimum.5. Fan Control: Field adjustable down to approximately half-speed.6. Total Wattage: 950 W, maximum; with heater.7. Runtime: Field adjustable or automatic, up to 35 seconds.8. Supply Voltage: As indicated on drawings.9. Warranty: 3 years.

http://global.ihs.com/doc_detail.cfm?rid=BSD&document_name=ASTM%20C1503















































TOILET ACCESSORIES Job Number 2150319.0010 28 00 - 4/4

10. Electric Hand Dryer Products:a. Excel Dryer Inc.; ThinAir Hand Dryer: www.exceldryer.com/#sle.b. Substitutions: Section 01 60 00 - Product Requirements.

2.06 UTILITY ROOM ACCESSORIES

A. Mop and Broom Holder: 0.05 inch thick stainless steel, Type 304, hat-shaped channel.1. Holders: 3 spring-loaded rubber cam holders.2. Length: 36 inches.3. Products:

a. __________.b. Substitutions: Section 01 60 00 - Product Requirements.

PART 3 EXECUTION

3.01 EXAMINATION

A. Verify existing conditions before starting work.

B. Verify exact location of accessories for installation.

C. For electrically-operated accessories, verify that electrical power connections are ready and in thecorrect locations.

3.02 PREPARATION

A. Deliver inserts and rough-in frames to site for timely installation.

B. Provide templates and rough-in measurements as required.

3.03 3.02INSTALLATION

A. Install accessories in accordance with manufacturers' instructions in locations indicated on thedrawings.

B. Install plumb and level, securely and rigidly anchored to substrate.

C. Mounting Heights: As required by accessibility regulations, unless otherwise indicated.1. Grab Bars: As indicated on the drawings.

3.04 PROTECTION

A. Protect installed accessories from damage due to subsequent construction operations.

END OF SECTION
































Yogi Tea – Tenant Improvement – Bid Set 060917 – Bid Set June 9, 2017

Job Number 2150319.00 COMMERCIAL PLUMBING FIXTURES22 42 00 - 1

SECTION 22 42 00

COMMERCIAL PLUMBING FIXTURES

1 PART 1 GENERAL

1.01 SUMMARY

A. Work included: Providing of all plumbing fixtures, fixture trim, cleanouts and appurtenances as shown or required.

B. Product Certification: Provide only products certified for use in the State of Oregon.

1.02 SUBMITTALS

A. Provide submittals in accordance with Section 22 00 00.

B. Submittals shall include manufacturer's catalog literature for all products used.

1.03 OPERATION AND MAINTENANCE DATA

A. Provide O&M data in accordance with Section 22 00 00.

B. O&M data shall include:1. Manufacturer's literature.2. Maintenance instructions.

2 PART 2 PRODUCTS

2.01 MANUFACTURERS

A. Vitreous China: Kohler, Sloan, American Standard or equal.

B. Flush-o-meters: Sloan, Kohler, American Standard, Zurn or equal.

C. Supplies and Stops: Speedway, McQuire, Zurn or Eastman.

D. Floor Drains and Floor Sinks: Jay R. Smith, Wade, Watts, Ancon or Zurn.

E. Cleanouts: Jay R. Smith, Wade, Watts Ancon or Zurn.

F. Carriers: Jay R. Smith, Wade, Watts Ancon or Zurn.

G. Priming Valves: Precision Plumbing Products only.

H. Water Hammer Arrestors: Smith or Precision Plumbing Products.

I. Compressed air fittings: Applied System Technology, Trans-air or equal.

J. Pressure reducing valve: Watts, Zurn, Wilkins or equal.

2.02 DESCRIPTION

A. Water Closet (WC-1): 1. American Standard “AFWALL" model 2859.111. White vitreous china, wall hung, elongated bowl,

high efficiency, 1 1/2” exposed inlet spud, flush valve toilet, Bowl only. Provide wall hanger.



2. American Standard “SELECTRONIC” model 6067.721 exposed water closet flush valve, Dual flush 1.1-1.28gpf, sensor operated. Hard wired w/ transformer. Coordinate electrical connections and requirements with electrical contractor.

3. Olsonite, model 10CT, elongated white plastic open front seat less cover with stainless steel hinge post and self-sustaining concealed check hinge.

4. See architectural drawings for mounting height

B. Water Closet (WC-2): ADA1. American Standard “AFWALL" model 2859.111. White vitreous china, wall hung, elongated bowl,

high efficiency, 1 1/2” exposed inlet spud, flush valve toilet. Bowl only. Provide wall hanger.2. American Standard “SELECTRONIC” model 6067.721 exposed water closet flush valve, Dual flush

1.1-1.28gpf, sensor operated. Hard wired w/ transformer. Coordinate electrical connections and requirements with electrical contractor.

3. Olsonite, model 10CT, elongated white plastic open front seat less cover with stainless steel hinge post and self-sustaining concealed check hinge.

4. See architectural drawings for mounting height.

C. Water Closet (WC-3): ADA1. American Standard “MADERA" model 2857.111. White vitreous china, floor mount, elongated

bowl, high efficiency, 1 1/2” exposed inlet spud, flush valve toilet, Bowl only. Provide wall hanger.2. American Standard “SELECTRONIC” model 6067.721 exposed water closet flush valve, Dual flush

1.1-1.28gpf, sensor operated. Hard wired w/ transformer. Coordinate electrical connections and requirements with electrical contractor.

3. Olsonite, model 10CT, elongated white plastic open front seat less cover with stainless steel hinge post and self-sustaining concealed check hinge

4. See architectural drawings for mounting height

D. Urinal (U-1): 1. American Standard “DECORUM" model 6042, white vitreous china, deep-sump, high efficiency

urinal. Bowl only.2. America Standard “SELECTRONIC” exposed, hard wired, AC powered, 0.5gpf, sensor operated

urinal flush valve. Hard wired w/ transformer. Coordinate electrical connections and requirements with electrical contractor.

E. Urinal (U-2): ADA1. American Standard “DECORUM" model 6042, white vitreous china, deep-sump, high efficiency

urinal. Bowl only.2. America Standard “SELECTRONIC” exposed, hard wired, AC powered, 0.5gpf, sensor operated

urinal flush valve. Hard wired w/ transformer. Coordinate electrical connections and requirements with electrical contractor.

3. See architectural drawings for mounting height.

F. Lavatory (L-1): 1. Solid Surface counters, provided by others. 2. Delta “TECK” 590T Series, model 590T0251TR, sensor operated, chrome plated brass faucet, deck

mounted, ADA compliant, chrome plated brass grid strain.3. Hard wired 24VAC infrared electronic hand washing system. Coordinate electrical connections and

requirements with electrical contractor.

G. Lavatory (L-2): ADA1. Solid Surface counters, provided by others. 2. Delta “TECK” 590T Series, model 590T0251TR, 0.5gpm, sensor operated, chrome plated brass

faucet, deck mounted, ADA compliant, chrome plated brass grid strain.



3. Hard wired 24VAC infrared electronic hand washing system. Coordinate electrical connections and requirements with electrical contractor.

4. Truebro, ‘Lav Guard’ insulation kit, 100 series for water and waste, form-fit protector of white molded material meeting ASTM D-635 with smooth cleanable surface, accessible cleanout, shutoff valve covers and hardware.

H. Lavatory (L-3): ADA WALL MOUNTED1. American standard Lucerne “0356.028”2. Delta “TECK” 590T Series, model 590T0251TR, 0.5gpm, sensor operated, chrome plated brass

faucet, deck mounted, ADA compliant, chrome plated brass grid strain.3. Hard wired 24VAC infrared electronic hand washing system. Coordinate electrical connections and

requirements with electrical contractor.4. Truebro, ‘Lav Guard’ insulation kit, 100 series for water and waste, form-fit protector of white

molded material meeting ASTM D-635 with smooth cleanable surface, accessible cleanout, shutoff valve covers and hardware.

I. Shower (SH-1): 1. Fiber-Fab #38H1, one-piece, fiberglass, gel coat, 36” x 36”, soap ledge, anti-slip floor, extra-heavy

duty construction, pre-installed bolted through curtain rod.2. Moen Commercial, model 8342EP15, Three-function, commercial shower system, pressure

balancing shower trim. 1.5 gpm, arm and flange, Chrome plated metal, vandal resistant, w/ leaver blade handle Fiber-Fab #V140NC self-caulking, solid brass, polished chrome finish, shower drain.

J. Shower (SH-2): ADA1. Fiber-Fab #38H1BF, one-piece, fiberglass, gel coat, 36” x 36”, soap ledge, anti-slip floor, extra-

heavy duty construction, pre-installed bolted through curtain rod.2. Moen Commercial, model T9375EP15, single-handle, posi-temp, pressure balancing shower trim.

1.5 gpm, arm and flange, Chrome plated metal, vandal resistant w/ leaver blade handle Fiber-Fab #V140NC self-caulking, solid brass, polished chrome finish, shower drain.

K. Sink (S-1): 1. Elkay Model LR3122EK, overall 31” x 22” x 7 5/8” deep, single bowl, 18 gauge stainless steel, top

mount sink with “Pro Drain”, faucet ledge, fully undercoated, centered drain opening, Holes to match faucet. Elkay Model LK-35, stainless steel cup strainer.

2. Delta “TECK” model 26C3944, chrome plated faucet, heavy duty 6” radius 10-1/2” high chrome plated brass gooseneck swing spout, chrome plated stainless steel cover plate, two 4” blade handles, vandal resistant 1.0 gpm w/ laminar flow control.

L. Sink (S-1A): ADA1. Elkay Model LRADQ312265PD, overall 31” x 22” x 6-1/2” deep, single bowl, 18 gauge stainless

steel, top mount sink with “Pro Drain”, faucet ledge, fully undercoated, centered drain opening, Holes to match faucet. Elkay Model LK-35, stainless steel cup strainer.


M. Sink (S-2): ADA, 1. Elkay ‘Lustertone’ Model LRAD331965PD, overall 33” x 19 1/2” x 6-1/2” deep, double bowl, 18

gauge stainless steel, , top mount sink with “Pro Drain”, faucet ledge, fully undercoated, centered drain opening, Holes to match faucet. Elkay Model LK-35, stainless steel cup strainer.


3. Pot Filler Delta 1177LF wall mounted. Dual handle design. ADA compliant.



N. Sink (S-3):1. (3) Compartment sink, dual faucet, sink. Relocated from existing facility. 2. Delta “TECK” model 26C3944, chrome plated faucet, heavy duty 6” radius 10-1/2” high chrome

plated brass gooseneck swing spout, chrome plated stainless steel cover plate, two 4” blade handles, vandal resistant 1.0 gpm w/ laminar flow control.

3. Delta “TECK” model 55P1513 Heavy duty, Pre-rinse, 1.6gpm, ADA compliant, polished chrome finish.

O. Sink (S-4): ADA, 1. Elkay ‘Lustertone’ Model LRAD171665PD, overall 17” x 16” x 6-1/2” deep, single bowl, 18 gauge

stainless steel, , top mount sink with “Pro Drain”, faucet ledge, fully undercoated, centered drain opening, Holes to match faucet. Elkay Model LK-35, stainless steel cup strainer.

2. Delta “TECK” model 26C3944, chrome plated faucet, heavy duty 6” radius 10-1/2” high chrome plated brass gooseneck swing spout, chrome plated stainless steel cover plate, two 4” blade handles, vandal resistant 1.0 gpm w/ laminar flow control

P. Service Sink (SS-1): 1. Stern Williams "SERVICEPTOR" Model SB302, terrazzo service sink, 36” x 36” x 12” high,

rectangular with stainless steel cap.2. T-35: Hose and wall hook 36” long hose with stainless steel hanger bracket, 3. BP-2: Splash catcher panels of 20g type 304 stainless steel, 4. Cast brass drain with stainless steel strainer5. Delta model 28T9 faucet with vacuum breaker spout, 3/4" hose thread outlet, pail hook with wall

support and metal cross handles.

Q. Service Sink (SS-2): 1. Stern Williams "SERVICEPTOR" Model SB302, terrazzo service sink, 36” x 36” x 12” high,

rectangular with stainless steel cap.2. T-35: Hose and wall hook 36” long hose with stainless steel hanger bracket, 3. BP-2: Splash catcher panels of 20g type 304 stainless steel, 4. Cast brass drain with stainless steel strainer5. Delta model 28T9 faucet with vacuum breaker spout, 3/4" hose thread outlet, pail hook with wall


R. Service Sink (LS-1): 1. Stern Williams "HI-LOW" Model HL-2000 , terrazzo service sink, 36” x 36” x 12” high, square with

stainless steel threshold cap.2. T-35: Hose and wall hook 36” long hose with stainless steel hanger bracket, 3. BP-2: Splash catcher panels of 20g type 304 stainless steel, 4. Cast brass drain with stainless steel strainer5. Delta model 28T9 faucet with vacuum breaker spout, 3/4" hose thread outlet, pail hook with wall


S. Hand Sink (HS-1): 1. Elkay model EHS-14PEDX, Economy series, Hand Sink, 18 ga stainless steel, 6” backsplash w/ 2”

return, wall mounted with pedestal w/ foot valve, Gooseneck faucet, chrome strainer.

T. Hand Sink (HS-2): 1. Elkay model EHS-14PEDX, Economy series, Hand Sink, 18 ga stainless steel, 6” backsplash w/ 2”

return, Pedestal w/ foot valve, Gooseneck faucet, chrome strainer. 2. Elkay to custom fabricate hand sink pedestal. See architectural drawings for details.

U. Bottle Filler (BF-1): Murdock BF48 Series semi-recessed sensor operated bottle filler, refrigerated, 8 gallons per hour, hardwired, lead free, vandal resistant. Coordinate power with electrical contractor.



V. Bottle Filler (BF-2): Murdock BF4 Series semi-recessed sensor operated bottle filler, non-refrigerated, hardwired, lead free, vandal resistant. Coordinate power with electrical contractor.

W. Electric Water Cooler (EWC-1): Elkay “EZTL8” model EZ(S)TLR8. Filtered, dual height, cooler. Coordinate electrical connection with electrical contractor.

X. Valve Box (VB-1): Guy Gray Model BIM875, steel box with epoxy finish, 1/2” FIP inlet x 1/4” OD outlet, compression angle stop.

Y. Emergency Eyewash (EEW-1): Haws model 8309WC, Combination shower and eye/face wash. Provide with tempering valve.

Z. Emergency Eyewash (EEW-2): Haws “AXION” model 7620, EYEPOD, faucet-mounted eyewash, adjustable outlet heads, Provide with tempering valve (TV-1): Haws model 9201EW, Emergency fixture thermostatic mixing valve.

AA. Tempering Valve (TV-1): Haws “AXION” model 920H Thermostatic mixing valve. Lead Free, Flow rate 1- 31gpm, 125psi operating pressure, cold water bypass, 1” inlets, 1 1/4” outlet.

BB. Insta-Hot water dispenser (IH-1): Insinkerator HOT100. 2/3gal tank, 60 cups per hour, 160-210 degree hot water range. Factory outlet temperature set to 200 degrees.

CC. Garbage Disposal (GD-1): Insinkerator “BADGER 5XP” 3/4hp, galvanized steel construction. Coordinate electrical requirements and connections with electrical contractor.

DD. Pressure reducing Valve (PRV-1): Watts model LF25AUB-Z, Lead free, integral strainer, bypass, adjustable pressure outlet.

EE. Hose Bibb (HB-2): Woodford Model SRH-MS, Freezeless, no drain required, dual check valve, flanges for roof installation.

3 PART 3EXECUTION

3.01 INSTALLATION

A. Provide plumbing fixture trim where applicable on fixture.

B. Plumbing Fixtures:1. Plumbing Fixtures Mounting Heights: All fixtures standard rough-in catalogued heights unless

specified or shown otherwise on the architectural drawings.2. Cleanout:

a. Where required for purposes intended.b. Cover set flush with finished surface.

3. Floor Drain: Set top flush with finished floor unless otherwise noted on architectural drawings.

C. Priming Valves:1. Floor drain and Floor Sink traps primed with priming valves with 3/8" copper pipe.2. Six traps maximum primed from one priming valve.3. Where priming valves are installed in finished rooms, conceal in wall and provide access door.4. Install shutoff valve ahead of priming valve.

D. Water Hammer Arrestors (WHA): Provide where shown and where recommended by Plumbing Drainage Institute (PDI). Furnish access panel to allow repair or replacement.



E. Drawings are diagrammatic and may not show all required cleanouts and fittings. Provide additional required items at no additional cost.

END OF SECTION

Yogi Tea – Tenant Improvement – Bid Set 060917 – Bid Set Addendum 1 - June 16, 2017

Job Number 2150319.00 PACKAGED ROOFTOP HVAC EQUIPMENT

23 74 00 - 1

SECTION 23 74 00

PACKAGED ROOFTOP HVAC EQUIPMENT

1 PART 1 GENERAL

1.01 WORK INCLUDED

A. Provide U.L. approved package rooftop air handling units as specified and scheduled herein.

1.02 SUBMITTALS

A. Manufacturers' catalog or technical data substantiating performance required. Mark up literature to indicate operating points.

B. Show all dimensions and describe materials and methods of construction.

C. Show and describe recommended methods of installation.

1.03 OPERATION AND MAINTENANCE DATA

A. Furnish O&M data including manufacturer's literature and maintenance instructions.

B. Furnish complete operation and maintenance manuals noting service points and recommended service schedules. Note specific techniques and equipment recommended for this equipment service.

2 PART 2 PRODUCTS

2.01 MAKEUP AIR UNIT (MUA-1)

A. Acceptable Manufacturers: Trane, Carrier, Daikin or approved equal.

B. General Description 1. Variable volume packaged rooftop unit shall include compressors, evaporator coils, filters, supply

fans, dampers, air-cooled condenser coils, condenser fans, gas furnace sections, exhaust fans / return fans and variable frequency drives.

2. Unit shall be factory assembled and tested including leak testing of the coils, pressure testing of the refrigeration circuit, and run testing of the completed unit. Run test report shall be supplied with the unit in the controls compartment’s literature pocket.

3. Unit components shall be labeled, including pipe stub outs, refrigeration system components and electrical and controls components.

4. Installation, Operation and Maintenance manual shall be supplied within the unit. 5. Laminated color-coded wiring diagram shall match factory installed wiring and shall be affixed to

the interior of the control compartment’s access door. 6. Unit nameplate shall be provided in two locations on the unit, affixed to the exterior of the unit

and affixed to the interior of the control compartment’s access door.

C. Construction 1. All cabinet walls, access doors, and roof shall be fabricated of double wall, impact resistant, rigid

polyurethane foam panels. 2. Unit insulation shall have a minimum thermal resistance R-value of 13. Foam insulation shall have a

minimum density of 2 pounds/cubic foot and shall be tested in accordance with ASTM D-1929-11 for a minimum flash ignition temperature of 610°F.



23 74 00 - 2

3. Unit construction shall be double wall with G90 galvanized steel on both sides and a thermal break. Double wall construction with a thermal break prevents moisture accumulation on the insulation, provides a cleanable interior, prevents heat transfer through the panel, and prevents exterior condensation on the panel.

4. Roof of the air tunnel shall be sloped to provide complete drainage. Cabinet shall have rain break overhangs above access doors.

5. Access to filters, dampers, cooling coils, reheat coil, heaters, exhaust fans, return fans, energy recovery wheels, compressors, water-cooled condensers, and electrical and controls components shall be through hinged access doors with quarter turn, zinc cast, lockable handles. Full length stainless steel piano hinges shall be included on the doors.

6. Exterior paint finish shall be capable of withstanding at least 2,500 hours, with no visible corrosive effects, when tested in a salt spray and fog atmosphere in accordance with ASTM B 117-95 test procedure.

7. Units with cooling coils shall include double sloped 304 stainless steel drain pans. 8. Unit shall be provided with base discharge and return air openings. All openings through the base

pan of the unit shall have upturned flanges of at least 1/2 inch in height around the opening. 9. Unit shall include lifting lugs on the top of the unit. 10. Unit base pan shall be provided with 1/2 inch thick foam insulation.

D. Electrical 1. Unit shall be provided with factory installed and factory wired, non-fused disconnect switch. 2. Unit shall be provided with factory installed and factory wired 115V, 13 amp GFI outlet with outlet

disconnect switch in the unit control panel. 3. Unit shall be provided with phase and brown out protection which shuts down all motors in the

unit if the electrical phases are more that 10% out of balance on voltage, the voltage is more that 10% under design voltage, or on phase reversal.

4. Unit shall be provided with manual reset low temperature limit controls which shut off the unit when the discharge temperature reaches a field adjustable setpoint.

E. Supply Fans 1. Unit shall include direct drive, unhoused, backward curved, plenum supply fans. 2. Blowers and motors shall be dynamically balanced and mounted on rubber isolators. 3. Motors shall be standard (premium) efficiency ODP with ball bearings rated for 200,000 hours

service with external lubrication points. 4. Variable frequency drive shall be factory wired and mounted in the unit. Fan motors shall be

premium efficiency.

F. Cooling Coils 1. Coils shall be designed for use with R-410A refrigerant and constructed of copper tubes with

aluminum (copper) fins mechanically bonded to the tubes and galvanized steel end casings. Fin design shall be sine wave rippled.

2. Coils shall have interlaced circuitry and shall be standard capacity. 3. Coils shall be hydrogen or helium leak tested. 4. Coils shall be furnished with a factory installed expansion valves.

G. Refrigeration System 1. Unit shall be factory charged with R-410A refrigerant. 2. Compressors shall be scroll type with thermal overload protection and carry a 5 year non-prorated

warranty, from the date of original equipment shipment from the factory. 3. Compressors shall be mounted in an isolated service compartment which can be accessed without

affecting unit operation. Lockable hinged compressor access doors shall be fabricated of double wall, rigid polyurethane foam insulated panels to prevent the transmission of noise outside the cabinet.



23 74 00 - 3

4. Compressors shall be isolated from the base pan with the compressor manufacturer’s recommended rubber vibration isolators, to reduce any transmission of noise from the compressors into the building area.

5. Each refrigeration circuit shall be equipped with expansion valve type refrigerant flow control. 6. Each refrigeration circuit shall be equipped with automatic reset low pressure and manual reset

high pressure refrigerant safety controls, Schrader type service fittings on both the high pressure and low pressure sides, and factory installed liquid line filter driers.

7. Unit shall include a variable capacity scroll compressor on the lead (all) refrigeration circuit(s) which shall be capable of modulation from 10-100% of its capacity.

8. Each refrigeration circuit shall be equipped with suction and discharge compressor isolation valves. 9. Each capacity stage shall be equipped with a 5 minute off, delay timer to prevent compressor short

cycling. 10. Each refrigeration circuit shall include adjustable compressor lockouts. 11. Each refrigeration circuit shall be provided with an adjustable temperature sensor freeze stat

which shuts down the cooling circuits when the evaporator coil tubing falls below the setpoint.

H. Condensers 1. Condenser fans shall be vertical discharge, axial flow, direct drive fans. 2. Coils shall be designed for use with R-410A refrigerant. Coils shall be multi-pass and fabricated

from aluminum microchannel tubes. 3. Coils shall be designed for a minimum of 10F of refrigerant sub-cooling. 4. Coils shall be hydrogen or helium leak tested.

I. Gas Heating 1. Unit shall include a natural gas furnace with modulation. Natural gas furnace shall be equipped

with modulating gas valves, adjustable speed combustion blowers, stainless steel tubular heat exchangers, and electronic controller. Combustion blowers and gas valves shall be capable of modulation. Electronic controller includes a factory wired, field installed supply air temperature sensor. Sensor shall be field installed in the supply air ductwork. Supply air temperature setpoint shall be adjustable on the electronic controller within the controls compartment. 90 MBH, 150 MBH, 195 MBH, 210 MBH, 270 MBH, 292.5 MBH, 390 MBH, 540 MBH and 800MBH gas heating assemblies shall be capable of operating at any firing rate between 100% and 30% of their rated capacity. 405 MBH and 810 MBH gas heating assemblies shall be capable of operating at any firing rate between 100% and 20% of their rated capacity. 1080 MBH and 1600 MBH gas heating assembly shall be capable of operating at any firing rate between 100% and 15% of its rated capacity. 2400 MBH gas heating assembly shall be capable of operating at any firing rate between 100% and 10% of its rated capacity.

2. Stainless steel heat exchanger furnace shall carry a 25 year non-prorated warranty, from the date of original equipment shipment from the factory.

3. Gas furnace shall consist of stainless steel heat exchangers with multiple concavities, an induced draft blower and an electronic pressure switch to lockout the gas valve until the combustion chamber is purged and combustion airflow is established.

4. Furnace shall include a gas ignition system consisting of an electronic igniter to a pilot system, which will be continuous when the heater is operating, but will shut off the pilot when heating is not required.

5. Unit shall include a single gas connection and have gas supply piping entrances in the unit base for through-the-curb gas piping and in the outside cabinet wall for across the roof gas piping.

J. Filters 1. Unit shall include 4 inch thick, pleated panel filters with an ASHRAE efficiency of 85% and a MERV

rating of 13, upstream of the cooling coil. Unit shall also include 2 inch thick, pleated panel pre filters with an ASHRAE efficiency of 30% and MERV rating of 8, upstream of the 4 inch standard filters.

2. Unit shall include a clogged filter switch.



23 74 00 - 4

3. Unit shall include a Magnehelic gauge mounted in the controls compartment.

K. Unit shall include 2 inch thick, pleated panel outside air and exhaust air filters with an ASHRAE efficiency of 30% and MERV rating of 8, upstream of the wheels.

L. Roof Curb: Furnish seismic rated, spring isolated roof curb manufactured to provide a level mounting surface. Verify exact requirements prior to equipment order.

M. Controls 1. System Manager with touch screen panel and browser based interface.

a. Plug-and-Play with Daikin MicroTech III equipment b. Large color touch-screen display for easy access c. Embedded Windows d. Intuitive browser based user interface e. Current status and setpoint access for all equipment f. Customizable control sequences and alarms g. Custom and graphical trend information h. Global actions i. Wall mount bracket for easy installation of System Manager PC and touchscreen

2. Factory installed RTU controller a. Unit controller shall be capable of controlling all features and options of the unit. Controller

shall be factory installed in the unit controls compartment and factory tested. Controller shall be capable of standalone operation with unit configuration, setpoint adjustment, sensor status viewing, unit alarm viewing, and occupancy scheduling available without dependence on a building management system.

b. Controller shall have an onboard clock and calendar functions that allow for occupancy scheduling.

c. Controller shall include non-volatile memory to retain all programmed values without the use of a battery, in the event of a power failure.

3. Provide a complete integrated microprocessor based Direct Digital Control (DDC) system to control all unit functions including temperature control, scheduling, monitoring, unit safety protection, including compressor minimum run and minimum off times, and diagnostics. This system shall consist of all required temperature sensors, pressure sensors, controller and keypad/display operator interface. All MCBs and sensors shall be factory mounted, wired and tested.

4. The stand-alone DDC controllers shall not be dependent on communications with any on-site or remote PC or master control panel for proper unit operation. The microprocessor shall maintain existing set points and operate standalone if the unit loses either direct connect or network communications. The microprocessor memory shall be protected from voltage fluctuations as well as any extended power failures. All factory and user set schedules and control points shall be maintained in nonvolatile memory. No settings shall be lost, even during extended power shutdowns.

5. The DDC control system shall permit starting and stopping of the unit locally or remotely. The control system shall be capable of providing a remote alarm indication. The unit control system shall provide for outside air damper actuation, emergency shutdown, remote heat enable/disable, remote cool enable/disable, heat indication, cool indication, and fan operation.

6. All digital inputs and outputs shall be protected against damage from transients or incorrect voltages. All field wiring shall be terminated at a separate, clearly marked terminal strip.

7. The DDC controller shall have a built-in time schedule. The schedule shall be programmable from the unit keypad interface. The schedule shall be maintained in nonvolatile memory to insure that it is not lost during a power failure. There shall be one start/stop per day and a separate holiday schedule. The controller shall accept up to sixteen holidays each with up to a 5-day duration. Each unit shall also have the ability to accept a time schedule via BAS network communications.



23 74 00 - 5

8. The keypad interface shall allow convenient navigation and access to all control functions. The unit keypad/display character format shall be 4 lines x 20 characters. All control settings shall be password protected against unauthorized changes. For ease of service, the display format shall be English language readout. Coded formats with look-up tables will not be accepted.

2.02 PACKAGED CONSTANT AIR VOLUME ROOFTOP UNITS

A. Acceptable Manufacturers: Trane, Carrier, Daikin or approved equal.

B. Description: Roof-mounted, constant volume, designed for full curb mounting on factory-supplied curb, vertical intake and discharge, natural gas heat, capacities as indicated, factory assembled, wired, piped, tested and shipped in one piece with U.L. listing, with single point electrical connection.

C. Housing: construct the unit housing of minimum 18-gauge galvanized steel formed exterior panels finished with rust inhibiting enamel coat. Standard finish color.

D. Provide minimum 1", 1-1/2 pound coated fiberglass insulation on exterior panels with neoprene door gasketing. Caulk all exterior panel-to-panel joints to provide watertight casing. Provide hinged doors to all portions of the RTU requiring routine maintenance.

E. Natural gas heating: completely assembled, wired, piped and tested, with threaded gas connections. Provide stainless steel heat exchanger and burners, forced draft combustion blower and electronic ignition.

F. Fans to be centrifugal type direct drive by a permanently lubricated premium efficiency motor.

G. Economizer: Provide outside air, return air and mixed air dampers capable of receiving control contractors actuators. Provide adjustable minimum outside air damper position. Control dampers to have a maximum leakage rate in compliance with current State of Oregon Energy Code requirements.

H. Power Exhaust: Provide a factory installed power exhaust when scheduled operated by an adjustable end switch. Exhaust fans to be manufacturer's standard option when available or manufacturer's approved field conversion option when not available from the factory.

I. Options / Accessories: 1. Hinged access doors. 2. Through the base electrical. 3. Through the base gas.

J. Roof Curb: Provide factory rooftop curb manufactured to provide a level mounting surface with a sloped roof installation. Verify exact requirements prior to equipment order.

K. Controls - RTU Single Zone - Provide a programmable electronic night setback thermostat. Thermostat shall perform the following functions. 1. Outdoor air temperature sensor input. 2. Auto-changeover. 3. Non-volatile memory to retain settings during power failure. 4. Keypad lockout. 5. Filter replacement indicator. 6. 7, 5-2 – All days programmable. 7. Overide control to allow unit operation outside of normal schedule by operation of an integral

button. Timed override will be 30 minutes per pulse with a maximum override of 180 minutes. 8. 5-degree minimum deadband between heating and cooling modes. 9. Programmable setup/setback temperature. 10. Fan operation continuous during days, intermittent during nights.



23 74 00 - 6

L. Controls - RTU VVT Control. 1. Trane Varitrac CCP with Operator Display option, communicating VVT dampers, actuators, zone

sensors. Note: Bypass dampers are integral with roof curbs and will require actuators and communication wiring. a. CO2 control (as required by zones). b. Zone based control operates heating and cooling only when zone demand exists. c. Discharge air control. d. Global zone temperature setpoint limits.

2. Energy Compliance: a. Provide 365 day, 24 hour occupancy scheduling. b. Provide software routines to operate the furnace to maintain the minimum night low limit

temperature for that system. c. When controlling both heating and cooling (mechanical), provide a 5-degree deadband in

which the heating energy provided to the zone is reduced to a minimum. d. Close outside air dampers as appropriate to the equipment when the units are off and

during the warm-up period. 3. Occupied Mode:

a. VVT terminal units shall be networked to a central controller, which, based on the multiple zones comfort requirements, provides a staged "heat" or "cool" decision to be used by the building air conditioning unit. A variable air volume bypass air control terminal shall modulate to maintain a minimum air flow across the supply air conditioning unit.

b. The unit controller continuously monitors the zone temperature against its setpoint and varies the damper position to meet the zone requirements.

c. If cooling to the zone is required and the rooftop unit is in heating mode - Modulate damper to its minimum position.

d. If heating to the zone is required and the rooftop unit is in cooling mode - Modulate damper to its minimum position.

e. Provide a prioritization methodology with continuous data collection allowing individual zones to be weighted in importance for overall control of the RTU heating and cooling modes.

4. CO2 Control: If the return air CO2 level increases a maximum of 400 ppm above setpoint, the control system shall modulate the outside air damper open to maintain return air CO2 levels below setpoint. When the return air CO2 level decreases below setpoint, the control system shall return the outside air damper to normal control. Assume initial setpoint of 400 ppm for ambient CO2 level.

5. Unoccupied Mode: The supply fan shall stop. The outside air and relief dampers shall close. When the zone temperature decreases below the night low limit setpoint, the control system shall index the unit to the morning warm-up mode. When the zone temperature has increased above the night low limit setpoint plus 5 degrees F, the control system shall index the unit to the unoccupied mode.

6. Morning warmup period: Terminal units go to full air volume until room heating setpoint is reached. At end of unoccupied warmup period, return to normal control. The unit will then operate in occupied mode.

7. Safeties: The supply fan shall stop, the outside air and relief dampers shall close and an alarm shall be generated if any of the listed events occur: a. High temperature alarm. b. Low temperature alarm.

M. Warranty: One year on all parts.



23 74 00 - 7

3 PART 3 - EXECUTION

3.01 INSTALLATION

A. Install rooftop units in accordance with the manufacturer's instructions. Do not start units until filters have been installed. Install a new set of filters upon job completion.

B. Provide a flexible connecter at all rigid connections to the unit.

C. Provide seismic bracing and supports as required by the governing jurisdiction for all units. Provide seismic restraint details and calculations as required by the governing code jurisdiction. Cost for all seismic detail development and calculations are to be included in the base bid price.

D. Roof Curb. 1. Mount the roof curb as noted on the drawings and in accordance with the manufacturer’s

installation instructions. 2. All areas within the roof curb excluding duct penetrations is to have two layers of 5/8” waterproof

sheetrock laid on staggered joints. The sheetrock must surround the ductwork to provide a continuous sound break. Caulk the sheet rock seams in the acoustical barrier to minimize sound transmission.

E. Provide flexible connections for ductwork attachment at the unit.

F. Provide gas pressure regulator at each unit to reduce gas pressure to 6” water column.

G. Start-up service to be performed by the manufacturer's authorized representative. Another separate visit for 2 hours of rooftop unit training shall be provided by manufacturer’s authorized representative at a time acceptable to both owner and manufacturer representative.

H. Controls. 1. Constant Volume Units – Install controllers, thermostats, dampers, actuators, relays, etc. with

required wiring for complete functioning systems. 2. Provide actuators with required control wiring to control the curb bypass damper for rooftop units

controlled by VVT controls. 3. Locate the VVT system Central Control Panel as requested by the owner’s representative and

provide all wiring for a complete, operating system. 4. MUA-1 – Provide control devices, relays, etc. for the following sequence.

a. Interlock with ERV-1 to start and stop with the laboratory hood exhaust fan. b. Interlock unit operation with hood fan switch. c. When one hood (exhaust fan) is started, the makeup air unit and ERV fan speed will modulate

to 50% and modulate the compressor and gas heat in sequence to maintain 72-degrees F. (adjustable).

d. The sequence will reverse on hood / exhaust fan shutdown.

3.02 COMMISSIONING

A. The equipment and systems referenced in this section are to be commissioned.

B. The contractor has specific responsibilities for scheduling, coordination, startup, test development, testing and documentation. Coordinate all commissioning activities with the Commissioning Authority.

END OF SECTION

D F I ISSUED

E ORIGINAL 8.5 x 11 U N DATE DATE DISTRIBUTION REMARKS: AS

L DRAWING/ 8.5 x 14 L I CHANGE CHANGE

T SPECIFICATION or L T (REVISION) (REVISION) NOTE: The purpose of this Document Change Log is to maintain a general record of revisions on

A NUMBER(S) 11 x 17 I ISSUED CLOSED a project. The information is purposefully concise and is not intended to provide detailed

SD# S A descriptions of revisions. All persons utilizing this log are responsible to review the drawings

H T and other documents related to each revision.

T E

KEY: 1. Owner | 2. Contractor | 3. A/E | 4. Governmental Agency | 5. Consultant | 6. Other

DOCUMENT CHANGE LOGMackenzie

1515 SE Water Ave, Ste 100, Portland OR 97214 (503) 224-9560 Fax (503) 228-1285

PROJECT NAME: PROJECT NUMBER: LOG AS OF:

YOGI TEA 2150319 06/26/2017

RFI, PR, ASI, CCD,

or CO

10 T1.1 X 6/22/2017 6/22/2017 Added to Sheet Index TI VE ADD 1

10 TA2.1A X 6/22/2017 6/22/2017 Modified Keynotes 09-28 and 10-20 TI VE ADD 1

10 TA2.1B X 6/22/2017 6/22/2017 Modified Keynotes 10-20 and 11-10 TI VE ADD 1

10 TA2.1B X 6/22/2017 6/22/2017 Revised bike lockers to bike shelters TI VE ADD 1

10 TA2.3A X 6/22/2017 6/22/2017 Revised rooftop unit labels and weights TI VE ADD 1

10 TA2.3A X 6/22/2017 6/22/2017 Added Bidding Note TI VE ADD 1

10 TA2.3B X 6/22/2017 6/22/2017 Revised rooftop unit labels and weights TI VE ADD 1

10 TA2.3B X 6/22/2017 6/22/2017 Added walk-off mats to office roof TI VE ADD 1

10 TA2.3B X 6/22/2017 6/22/2017 Added Bidding Note TI VE ADD 1

10 TA2.4A X 6/22/2017 6/22/2017 Added keynote 26-18 to Door 184 TI VE ADD 1

10 TA2.5A X 6/22/2017 6/22/2017 Added detail cuts 10/TA8.1 and 9/TA8.2 (sim) TI VE ADD 1

10 TA2.6A X 6/22/2017 6/22/2017 Added paint color note TI VE ADD 1

10 TA2.6B X 6/22/2017 6/22/2017 Added paint color note TI VE ADD 1

10 TA2.8 X 6/22/2017 6/22/2017 Added Keynote 10-22 and soap dispenser locations TI VE ADD 1

10 TA2.9 X 6/22/2017 6/22/2017 Added Keynotes 10-14, 10-15, and 10-22 TI VE ADD 1

10 TA2.9 X 6/22/2017 6/22/2017 Added mirors to 9/TA2.9 TI VE ADD 1

10 TA2.9 X 6/22/2017 6/22/2017 Added soap dispenser locations TI VE ADD 1

10 TA5.3 X 6/22/2017 6/22/2017 Added Keynotes 08-12 and 08-30; deleted Keynote 09-11 TI VE ADD 1

10 TA5.4 X 6/22/2017 6/22/2017 Revised duct hole sizes and locations to 1/TA5.4 TI VE ADD 1

10 TA5.4 X 6/22/2017 6/22/2017 Revised duct hole sizes to 2/TA5.4 TI VE ADD 1

10 TA5.5 X 6/22/2017 6/22/2017 Revised General Notes TI VE ADD 1

10 TA5.5 X 6/22/2017 6/22/2017 Added Keynotes 08-24 and 08-27 TI VE ADD 1

10 TA6.1 X 6/22/2017 6/22/2017 Added lighting fixture symbol schedule TI VE ADD 1



10 TA6.5 X 6/22/2017 6/22/2017 Revised Keynote 09-07 TI VE ADD 1

10 TA7.3 X 6/22/2017 6/22/2017 Revisions to details 1/TA7.3, 2/TA7.3, 3/TA7.3 and 4/TA7.3 TI VE ADD 1

10 TA7.3 X 6/22/2017 6/22/2017 Deleted detail 6/TA7.3 TI VE ADD 1

10 TA7.4 X 6/22/2017 6/22/2017 Added brace details 1/TA7.4 and 5/TA7.4 TI VE ADD 1

10 TA7.4 X 6/22/2017 6/22/2017 Added ladder detail 15/TA7.4 and associated note to detail 3/TA7.4 TI VE ADD 1

10 TA7.4 X 6/22/2017 6/22/2017 Modified details 11/TA7.4, 12/TA7.4, and 13/TA7.4 TI VE ADD 1

10 TA8.1 X 6/22/2017 6/22/2017 Modified stud note on details 1-6, 8, 15, and 17/TA8.1 TI VE ADD 1

10 TA8.1 X 6/22/2017 6/22/2017 Modified stroefront system locatinos on details 11-14 and 20/TA8.1 TI VE ADD 1

10 TA8.1 X 6/22/2017 6/22/2017 Added vapor retarder to details 11-14/TA8.1 TI VE ADD 1

10 TA8.1 X 6/22/2017 6/22/2017 Modified details 7, TA8.1 and 10/TA8.1 TI VE ADD 1

10 TA8.2 X 6/22/2017 6/22/2017 Revised description & SIM condition to details 9/TA8.2 and 10/TA8.2 TI VE ADD 1

10 TA8.2 X 6/22/2017 6/22/2017 Modified graphics & notes on details 6/TA8.2, 11/TA8.2, 12/TA8.2, 14/TA8.2 TI VE ADD 1

10 TA8.4 X 6/22/2017 6/22/2017 Modified notes to 2/TA8.4 and 5/TA 8.4 TI VE ADD 1

10 TA8.4 X 6/22/2017 6/22/2017 Modified detail 12/TA8.4 TI VE ADD 1

10 TA8.5 X 6/22/2017 6/22/2017 Deleted detail 2/TA8.5 TI VE ADD 1

10 TA9.1 X 6/22/2017 6/22/2017 Revised FRP-1, SAT-1, TC-1, Shade-1, Shade-2, and Shade-3 from the Finish Materials

Schedule

TI VE ADD 1

10 TA9.1 X 6/22/2017 6/22/2017 Modified ceilings in Rooms 177, 178, 180, 181, 183, and 214 on Finish Schedule TI VE ADD 1

10 TA9.2 X 6/22/2017 6/22/2017 Added to Abbreviations list TI VE ADD 1

10 TA9.2 X 6/22/2017 6/22/2017 Deleted Door type A, C, and F (not used) from Door Type Schedule TI VE ADD 1

10 TA9.2 X 6/22/2017 6/22/2017 Modified detail callouts on Door Type Schedule TI VE ADD 1

D F I ISSUED

E ORIGINAL 8.5 x 11 U N DATE DATE DISTRIBUTION REMARKS: AS

L DRAWING/ 8.5 x 14 L I CHANGE CHANGE

T SPECIFICATION or L T (REVISION) (REVISION) NOTE: The purpose of this Document Change Log is to maintain a general record of revisions on

A NUMBER(S) 11 x 17 I ISSUED CLOSED a project. The information is purposefully concise and is not intended to provide detailed

SD# S A descriptions of revisions. All persons utilizing this log are responsible to review the drawings

H T and other documents related to each revision.

T E

KEY: 1. Owner | 2. Contractor | 3. A/E | 4. Governmental Agency | 5. Consultant | 6. Other

DOCUMENT CHANGE LOGMackenzie

1515 SE Water Ave, Ste 100, Portland OR 97214 (503) 224-9560 Fax (503) 228-1285

PROJECT NAME: PROJECT NUMBER: LOG AS OF:

YOGI TEA 2150319 06/26/2017

RFI, PR, ASI, CCD,

or CO

10 TA9.2 X 6/22/2017 6/22/2017 Modified window types a, g, and h TI VE ADD 1

10 TA9.2 X 6/22/2017 6/22/2017 Added typ details cuts to Window Type Schedule TI VE ADD 1

10 TA9.2 X 6/22/2017 6/22/2017 Added slider track detail (1) to Window Type Schedule TI VE ADD 1

10 TA9.2 X 6/22/2017 6/22/2017 Modified Doors 136B, 152A, 152B, 155A, 211, 216, 218, and 219 on the Door Schedule TI VE ADD 1

10 TS1.0 X 6/22/2017 6/22/2017 Revised Structural Deferred Submittals list TI VE ADD 1

10 TS1.1 X 6/22/2017 6/22/2017 Revised Header Schedule and Steel Stud Size Schedule TI VE ADD 1

10 TP0.1, TP2.1A, TP2.1B, TP2.2A, TP2.2B,

TP2.4A, TP2.4B, TP2.5A, TP2.5B

X 6/22/2017 6/22/2017 TI VE Addendum #1 Plumbing Revisions TI VE ADD 1

10 TM1.01, TM1.02, TM1.03, TM2.1A,

TM2.1B, TM2.5A, TM2.5B, TM2.5C,

TM3.1, TM3.2, TM3.3, TM3.4

X 6/22/2017 6/22/2017 TI VE Addendum #1 Mechanical Revisions TI VE ADD 1

10 TE3.1A, TE3.1B, TE4.0, TE4.4A, TE4.5B,

TE5.4, TE5.5, TE5.6, TE5.7, TE7.1

X 6/22/2017 6/22/2017 TI VE Addendum #1 Electrical Revisions TI VE ADD 1

TI VE Addendum #1 - Revision Closed 06/22/2017