tems hasp hl srm hardware key info

LZT 108 8446 Rev D

TEMS™ HASP HL SRM Hardware Key Info

Contents

1 The HASP HL SRM Hardware Key ...................................................... 3

2 Using the HASP HL SRM Hardware Key............................................. 32.1 Permanent Registration Copy ................................................................ 32.2 Trial Copy .............................................................................................. 32.3 Lease Copy............................................................................................ 3

3 Using the HASP HL SRM Key Reader................................................. 4

4 Updating the HASP HL SRM Hardware Key ....................................... 44.1 When Updates Are Needed ................................................................... 44.2 The Remote Update System Application................................................ 44.2.1 Running the HASP HL SRM Remote Update System Application.......... 44.2.2 Running the HASP HL Remote Update System Application................... 54.2.3 Requesting New Registration Information .............................................. 64.2.4 Updating Registration Information.......................................................... 6

5 Updating the Hardware Key Firmware for HASP HL SRM................. 7

6 Customer Support Contact Information............................................. 8


LZT 108 8446 Rev D 2009-05-18 Ascom 2009Public

3 (8)

1 The HASP HL SRM Hardware KeyYour TEMS software package contains a hardware key for your PC, which is a hardware-based solution for licensing the software. Without this hardware key you cannot run your TEMS application.

A damaged hardware key will be replaced for a replacement charge upon receipt of the damaged hardware key. There will be no replacement of a hardware key that has been lost, stolen, etc. In the latter case a new software license must be purchased.

The hardware key is plugged into the PC.

Example of hardware key (USB local)

2 Using the HASP HL SRM Hardware Key

2.1 Permanent Registration CopyAttach your hardware key to your computer. You can then start the TEMS application and use it indefinitely (no expiration date).

2.2 Trial CopyAttach your hardware key to your computer. You can then start the TEMS application and use it until the key expires.

2.3 Lease CopyAttach your hardware key to your computer. You can then start the TEMS application and use it for one year. The hardware key is programmed to expire in one year and seven days. (The seven days are added to compensate for shipping time.)



4 (8)

3 Using the HASP HL SRM Key ReaderSome TEMS applications include a utility called HASP HL SRM Key Reader which can check and display what is covered by your license. How to launch this utility is described in the user’s manual for your TEMS application.

4 Updating the HASP HL SRM Hardware Key

4.1 When Updates Are NeededAn update of the hardware key information is necessary when converting a trial or evaluation hardware key into a permanent or lease hardware key (see chapter 2).

An update is also necessary when upgrading a hardware key supporting an earlier version of your TEMS application to support a later version, or when adding new license options.

4.2 The Remote Update System ApplicationTo modify the programming of hardware keys, the Remote Update System application is used.

When updating from an older TEMS application using HASP HL to a current one using HASP HL SRM, you need to run two versions of the Remote Update System application. See below.

4.2.1 Running the HASP HL SRM Remote Update System Application

Make sure you have installed your TEMS application software. Then plug your hardware key into the PC. Navigate to the Application folder beneath the TEMS application’s installation directory and run the file “hasprus.exe”. This dialog box opens:



5 (8)

Remote Update System dialog: Collect Key Status Information tab

Now collect the key information by clicking the Collect information button. A file with extension .c2v is created. Choose a suitable file name and save the file. This file will be used in section 4.2.3.

If you get an error message like the one below, you need to upgrade the hardware key firmware to enable SRM functionality. See chapter 5.

Remote Update System dialog: Error message

4.2.2 Running the HASP HL Remote Update System Application

This procedure is identical to the one described in section 4.2.1 except that you run the file “hasprus_hl.exe” instead. It is found in the same directory as “hasprus.exe”. The output is again a *.c2v file, which you need to save.



6 (8)

4.2.3 Requesting New Registration Information

Contact customer support (see chapter 5) by e-mail, supplying the following information:

1 the HASP HL SRM *.c2v file obtained in section 4.2.1

2 the HASP HL *.c2v file obtained in section 4.2.2

3 the hardware key serial number (printed on the label that is stuck onto the hardware key)

4 the purchase order number of the upgrade.

4.2.4 Updating Registration Information

You will receive a file with extension .v2c from customer support. Once you have this file, you can update your hardware key as follows:

1 Make sure that the hardware key is physically attached to your computer.

2 Navigate to the TEMS application folder and run the file “hasprus.exe”. The Remote Update System dialog opens.

3 Select the Apply License Update tab.

4 Select the received file, and click the Apply update button. See the screenshot below.

Remote Update System dialog: Apply License Update tab



7 (8)

5 The result of the operation will be displayed in the main window of the dialog. When you have successfully updated the hardware key, exit the Remote Update System application.

6 You can now start using your TEMS application with the updated key.

5 Updating the Hardware Key Firmware for HASP HL SRM

If you received an error message when trying to retrieve the information stored in the hardware key, that is because the hardware key firmware is old and does not support SRM. You then need to upgrade the firmware:

1 First make sure that only one hardware key is connected to the PC.

2 The hardware key should be plugged into the PC directly, not through a USB hub.

3 Go to the Application directory beneath the TEMS application’s installation directory and run the file “FirmwareUpdate.exe”.

4 Click the Apply update button. The firmware will now be updated. Do not unplug the hardware key until notified that the update is complete.



8 (8)

6 Customer Support Contact Information

For customer support contact information, please visit our website: www.tems.com.

http://www.tems.com/

tems hasp hl srm hardware key info

Documents