technology thin films zno:al were prepared by rf diode sputtering from zno + 2wt % al 2 o 3 target....
TRANSCRIPT
Technology Thin films ZnO:Al were prepared by RF
diode sputtering from ZnO + 2wt % Al2O3 target.
It is a plasma assisted deposition method which involves a significant energetic bombardment of neutral atoms, ions and electrons on the growing film. RF power and substrate temperature are determining for the properties of sputtered ZnO films [ 3 ].
38 40 420
100
200
300
400
500
600
800 W
600 W400 W
Inte
ns
ity
(c
ps
)
2 (degrees)
200 W
40 420
500
1000
1500
2000
2500
300 °C
RT
100 °C
200 °C
300 °C
Inte
ns
ity
(c
ps
)
2 (degrees)
-110 -100 -90 -80 -700
2000
6000
8000
300 °C
200 °C
100 °C
RT
Inte
nsi
ty (
cps)
(degrees)
300°C
(002) (101)
RT
(002)
100°C
(002)
200°C
(002)
K. Shtereva1), S. Flickyngerová2), P. Šutta3), M. Netrvalová3), I. Novotný2) and V. Tvarožek2)
1) Department of Electronics, University of Rousse, Studentska 8, 7017 Rousse, Bulgaria2) Department of Microelectronics, Slovak University of Technology, Ilkovicova 3, 812 19 Bratislava, Slovakia3) West Bohemian University, New technologies – Research Centre, Univerzitni 8, 306 14 Plzen, Czech Republic
Transparent and conductive ZnO:Al Transparent and conductive ZnO:Al prepared by RF diode sputteringprepared by RF diode sputtering
IntroductionThe unique material properties in combination with a great natural abundance and low cost, make zinc oxide a promising transparent conducting oxide (TCO) for application in thin film solar cells and various optoelectronic devices [1, 2]. In addition it is an environment friendly material.
A matter of great importance for these industrial applications is the availability of a cost effective deposition technology. RF sputtering is such method that offers a deposition at low temperatures, safety advantages, and where the use of the toxic gases is avoided.
Structure characterizationXRD patterns show polycrystalline ZnO:Al thin films with a strong texture in the [001] direction perpendicular to the substrate
2-dimensional XRD patterns display elliptic diffraction spots of identically orientated polycrystals
The widths of azimuthal (002) line profiles (FWHM of the -scan ) decrease from 15 to 3.5° with increasing energy delivered to the growing film during the deposition
The up shift of the 2 with increasing RF powers and temperatures is a result of the increase of Al3+ substituents (Al3+ that substitute for Zn2+ in the ZnO lattice) and a reduction of the interplanar distance, which changes the lattice distortion in ZnO:Al films from compressive to tensile lattice stresses
Asymmetry of the (002) diffraction line indicates a region with heterogeneous structure at the substrate – film interface for films grown at room substrate temperature, and completely diminished at higher substrate temperatures
The RF power and temperature growth, result in the larger grains (growth from 60 to more than 200 nm) and better crystalline structure (no line asymmetry)
200 400 600 800 1000 120010-3
10-2
10-1
2
4
6
8
0.5
1.0
1.5
2.0
Co
nce
ntr
atio
n n
[10
20cm
-3]
Res
isti
vity
[
cm]
RF power P [W]
Mo
bil
ity H
[cm
2 / V
s]
H
n
0 100 200 30010-3
10-2
3
6
9
12
1.0
1.5
2.0
2.5
Co
nce
ntr
atio
n n
[10
20cm
-3]
Res
isti
vity
[
cm]
Substrate temperature Ts [°C]
Mo
bil
ity H
[cm
2 / V
s]
H
n
-100 0 100 200 30010-3
10-2
300°C
200°C
100°C
Substrate temperatureRT
Res
isti
vity
[
cm]
Hall measurement T [°C]
Electrical properties Minimum resistivity 2.6 x 10-3 cm, as a result of the highest carrier concentration 2 x 1020 cm-3 and mobility 7.81 cm2/Vs,
is obtained for ZnO:Al grown at 1200 W RF power and RT
The carrier concentration goes straightforwardly up (to 2.4 x 1020 cm-3) with increasing temperatures, as a result of the increased Al3+ substituents into the films
ZnO:Al thin films deposited with 800W and 200ºC exhibit strong degenerated semiconductor behaviour, the resistivity rises with the temperature at temperature-dependent Hall measurements
300 400 500 900 10000
20
40
60
80
100Corning glass
1200 W
1000 W
800 W
600 W
400 W
200 W
Tra
ns
mit
tan
ce
[%
]Wavelength [nm]
Optical properties The average transmittance of ZnO:Al thin films, including
Corning glass substrate, varies from 82 ÷ 86 % with increasing RF power
The sharp absorption edge appears at ~ 380 nm wavelength and the enlargement of the sputter power causes the blue shift of the cut – off wavelength
Optical bandgap Eg (~3.3 eV) widens with increasing RF power and temperature
1 µm
The surface images of ZnO:Al prepared with 800 W RF power and 200ºC substrate temperature obtained by means of SEM and AFM show a nanostructured surface
References
[1] Yoo J, Lee J, Kim S, Yoon K, Park I J, Dhunge S K, Karunagaran B, Mangalaraj D and Yi J 2005 Thin Solid Films 480–481 213– 217
[2] Hüpkes J, Rech B, Calnan S, Kluth O, Zastrow U, Siekmann H and Wuttig M 2006 Thin Solid Films 502 286 – 291
[3] Tvarozek V, Novotny I, Sutta P, Flickyngerova S, Schtereva K and Vavrinsky E 2007 Thin Solid Films doi:10.1016/j.tsf.2007.03.125 (in press)
Conclusions The properties of ZnO:Al thin films were considerable
modified by RF power and substrate temperature. The RF diode sputtering method can partially replace an influence of substrate temperature on growing film by the increasing of RF power, which becomes greater in the bombardment of substrate by energetic secondary electrons and ions.
The lowest resistivity (2 x 10-3 cm) and the highest mobility (12 cm2/Vs), carrier concentration (2 x 1020 cm-3) and transmittance ( > 82% including the substrate) are obtained in highly textured ZnO:Al films (widths of azimuthal line profiles (002) has a minimum FWHM ~3.26º) prepared at high RF power (800 W) and substrate temperature (200°C).
MotivationDevelopment:
high transparent and conductive ZnO:Al thin films for solar cells and optoelectronic devices application
Investigate correlations:
structure surface morphology electrical parameters optical parameters
STRUCTURE
Surface morphology
Optical
parameters
Elect
rical
param
eter
s