technical application guide for up-shine led downlight · 2017-11-07 · up-shine smd led down...
TRANSCRIPT
Up-shine SMD LED Down light adopts high lumen SMD LED, PC diffuser with even light output. Plastic coated aluminum housing with internal driver design; it is our most economical and practical downlight version. Dimmable driver shares great popularity by the excellent dimming effect.
● Up to 70% energy saving compared to standard CFL● Long lifetime of 40,000 hours ● Dimmable when using triac dimmer● 90° wide beam angle●70-75mm cutout● CCT: 3000K-4000K-5700K● No UV/IR light● Environment friendly, without Mercury or any other hazardous substances
Application notes● IP54 only for the LED cover, IP40 for other part● Professional electrician for installation only ● Switch off before installation● Do not touch when in use● Keep away from hot steam and corrosive gas
Application AreasIt is designed for general lighting applications in office, supermarket, shop, school, hotel, etc. It is also widely used for public areas, such as stairway, lobby, reception, corridors etc.
Certificate
Introduction
www.upshine.com [email protected]
Slide switch for color selection
SAA
Technical Specifications
Model Voltage Power PowerFactor
Lumen(±5%)
Beamangle CCT Lifespan CRI Dimmable Dimension
UP-DL41-2.5-7W-P3 AC230V 7W 0.9 560 90o 3000K 40000h ≥80 Yes Ø85*63mm cutout 70-75mm
UP-DL41-2.5-7W-P3 AC230V 7W 0.9 650 90o 4000K 40000h ≥80 Yes Ø85*63mm cutout 70-75mm
UP-DL41-2.5-7W-P3 AC230V 7W 0.9 600 90o 5700K 40000h ≥80 Yes Ø85*63mm cutout 70-75mm
www.upshine.com [email protected]
Product Information
Driver data SheetDriver data DIM
Input rated Voltage AC230V
Frequency 50Hz
Input Voltage AC200-240V
Efficiency ≥78%
Total load Wattage 7W±0.5W
Power Factor 0.9
Rated input current ≤0.04A
Full load output Voltage 50-64V
Rated output current 110mA
Output current range 110mA±5%
Power tolerance ±5%
Current output tolerance ±5%
Dimming range 8%-100%
Dimmer Triac dimmers
Short circuit protection PASS
Over voltage protection PASS
Over temperature protection PASS
THD ≤20%
Withstand voltage —
Fixture CompatibilityRated
WattageElectrical
ClassificationIngress
Protection Operating
TempOperatingHumidity
Storage Temp
7W Ⅱ IP40 / IP54 -20oC~45oC 0~90% -20oC~65oC
Ø85
Ø68
63
Photometric Diagram
Spectral Distribution
3000K
380 500 600 700 800Wavelength(nm)
Max=4453 [1.0=20000]
Spec
trum
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.0
4000K
5700K
380 500 600 700 800
380 500 600 700 800
Wavelength(nm)
Wavelength(nm)
Max=4679 [1.0=20000]
Max=6128 [1.0=20000]
Spec
trum
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.0
Spec
trum
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.0
2.91 SDCM F3000K
x=0.4458 y=0.4070
3.08 SDCM F4000K
x=0.3826 y=0.3766
5.86 SDCM F5700K
x=0.3380 y=0.3564
3000K
Polar intensity diagram Beam diagramCartesian intensity diagram
UNIT: cdAVERAGE BEAM ANGLE(50%): 105.1 DEG
-/+180
-120
-90
-30
120
90
30
0
60
120
180
240
300
0
Planar Illuminance Curve
Distance(m)
MH=10mE(LX)3.0
2.7
2.4
2.1
1.8
1.5
1.2
0.9
0.6
0.3
0
C0/180C90/270
-25 -20 -15 -10 -5 0 5 10 15 20 25 Height Eavg, Emax Angle: 104.22deg DiameterNote: The Curves indicate the illuminated area and the average illumination when the Luminaire is at different distance.
Flux out: 457.1 lm
4000K
Polar intensity diagram Beam diagramCartesian intensity diagram
UNIT: cdAVERAGE BEAM ANGLE(50%): 105.3 DEG
-/+180
-120
-90
-30
120
90
30
0
60
120
180
240
300
0
Planar Illuminance Curve
Distance(m)
MH=10mE(LX)3.0
2.7
2.4
2.1
1.8
1.5
1.2
0.9
0.6
0.3
0
C0/180C90/270
-25 -20 -15 -10 -5 0 5 10 15 20 25 Height Eavg, Emax Angle: 105.22deg DiameterNote: The Curves indicate the illuminated area and the average illumination when the Luminaire is at different distance.
Flux out: 507.7 lm
5700K
Polar intensity diagram Beam diagramCartesian intensity diagram
UNIT: cdAVERAGE BEAM ANGLE(50%): 105.4 DEG
-/+180
-120
-90
-30
120
90
30
0
60
120
180
240
300
0
Planar Illuminance Curve
Distance(m)
MH=10mE(LX)3.0
2.7
2.4
2.1
1.8
1.5
1.2
0.9
0.6
0.3
0
C0/180C90/270
-25 -20 -15 -10 -5 0 5 10 15 20 25 Height Eavg, Emax Angle: 105.35deg DiameterNote: The Curves indicate the illuminated area and the average illumination when the Luminaire is at different distance.
Flux out: 481.1 lm
www.upshine.com [email protected]
100
90
80
70
60
50
40
30
20
10
0
11:1
3:13
11:2
5:10
11:3
7:10
11:4
9:10
12:0
1:10
12:1
3:10
12:2
5:10
12:3
7:10
12:4
9:10
13:0
1:10
13:1
3:10
13:2
5:10
13:3
7:10
13:4
9:10
14:0
1:10
14:1
3:10
14:2
5:10
14:3
7:10
14:4
9:10
15:0
1:10
15:1
3:10
15:2
5:10
15:3
7:10
15:4
9:10
16:0
1:10
16:1
3:10
16:2
5:10
16:3
7:10
IC
Capacitor
MOS
PCB
LED
Fitting
Environmental temperature
Tem
pera
ture
(o C)
Time
The driver lifespan is based on capacitor working temperature.
Driver lifetime & LED light decay rate
90000
80000
70000
60000
50000
40000
30000
20000
10000
065oC 75oC 85oC 95oC 105oC
Life
time
(hou
rs)
Capacitor Tc (oC)
Driver Lifetime
% L
umin
ous
Flux
FLUX
△ U'V'
110%
105%
100%
95%
90%
85%
80%
75%
70%
0.0040
0.0035
0.0030
0.0025
0.0020
0.0015
0.0010
0.0005
0.00000 1000 2000 3000 4000 5000 6000 7000 8000 9000 10000
LifeTime (hours)
Polar Diagram Comparison
AVERAGE BEAM ANGLE (50%): 105.4DEG
UNIT: cd
C0/180, 105.3 deg
C30/210, 105.5 deg
C60/240, 105.5 deg
C90/270, 105.3 deg
60
120
180
240
300
0O
180O
150O-150O
120O-120O
90O-90O
60O-60O
30O-30O
0
LED Light Decay Rate
Temperature● The testing is operated at 25°C
● The lifetime of capacitor, minimum of 5,000 hours if operated at 105°C, will be doubled whenever the temperature drops 10°C
● The highest withstand temperature of IC, MOS could be 120°C
● The highest withstand temperature of LED junction temperature is 150°C
www.upshine.com [email protected]
Packaging Information
SIZE(CM) N.W/pc(KGS) G.W.(KGS) Q'TY(PCS)
Carton 55*55*17 0.2 11.5 50
CTNS Q'TY(PCS) VOLUME(CBM)
20'' standardcontainer 534 26700 28
40'' standardcontainer 1068 53400 56
www.upshine.com [email protected] Phone: +86 755 2919 7332Add: 2nd building Dingfeng High-Tech Zone, Fuyuan 1st road, Fu Yong Sub-district, Bao'an, Shenzhen China
For the product with Slide Switch of Color Selection, please select the light color (CW/NW/WW) before installation.
Light color changeable button
Installation Procedure
WARNING1.Switch off before installation.2.Switch on only after complete installation and examination of the circuit.3.Professional electrician for installation and maintenance only.
Turn Off power supply before starting any installation. Read instructions & check you have all the tools & accessories to complete the installation correctly.
1. Open a hole according to the cutout size of led downlight.
3. Connect the downlight with driver, hold back the spring clip then push the downlight into the hole.
4. Make sure the downlight fixed tightly in ceiling, turn on the power (Fig 1).
2. Use screw-driver to open the driver terminal cover, feed the main AC wire L. N. in terminal block respectively, then fix the cover back.