tbs190 op manual

CVR6TBS19OPS 31/03/08 www.snellwilcox.com Version 1 Issue 3 1

CVR600 & TBS190 Series

CVR600UDV CVR600UD CVR600BDV CVR600BD CVR600ADV CVR600AD

Standards Converters

TBS190ADV TBS190AD TBS190BDV TBS190BD TBS190UDV TBS190UD

Synchronizers

Operator’s Manual

© March 2008 www.snellwilcox.com Snell & Wilcox Ltd., Southleigh Park House, Eastleigh Road, Havant, Hants, PO9 2PE, United Kingdom. For General Enquiry’s contact: Tel: +44 (0) 2392 489000 Fax: +44 (0)23 9245 1411 For Technical assistance contact: Tel: +44 (0) 2392 489058 Fax: +44 (0) 2392 489057 Web: http://www.snellwilcox.com/support Ftp: ftp://ftp.snellwilcox.com/support

. . .

. . .

. . .

. . .



Explanation of Safety SymbolsThis symbol refers the user to important information contained in the accompanying literature. Refer to manual.

This symbol indicates that hazardous voltages are present inside. No user serviceable parts inside. This unit should only be serviced by trained personnel.

Servicing instructions where given, are for use by qualified service personnel only. To reduce risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Refer all servicing to qualified personnel.

To reduce the risk of electric shock, do not expose this appliance to rain or moisture.

Always ensure that the unit is properly earthed and power connections correctly made.

This equipment must be supplied from a power system providing a PROTECTIVE EARTH connection and having a neutral connection which can be reliably identified.

The power outlet supplying power to the unit should be close to the unit and easily accessible

Power connection in countries other than the USAThe equipment is normally shipped with a power cable with a standard IEC moulded free socket on one end and a standard IEC moulded plug on the other. If you are required to remove the moulded mains supply plug, dispose of the plug immediately in a safe manner.

The colour code for the lead is as follows:

GREEN/YELLOW lead connected to E (Protective Earth Conductor)BLUE lead connected to N (Neutral Conductor)BROWN lead connected to L (Live Conductor)

Caution If the unit has two mains supply inputs ensure that both power cords are plugged into mains outlets operating from the same phase.

L N

E

N L

E

GB

! CAUTIONRISK OF ELECTRIC SHOCKDO NOT REMOVE COVERS

NO USER SERVICEABLE PARTSREFER SERVICING TO QUALIFIED

PERSONNEL ONLY

!

!

Safety Warnings

Légende :Ce symbole indique qu'il faut prêter attention et se référer au manuel.

Ce symbole indique qu'il peut y avoir des tensions électriques à l'intérieur de l'appareil. Ne pas intervenir sans l'agrément du service qualifié.

Pour réduire le risque de choc électrique, ne pas exposer l'appareil dans un milieu humide.

Toujours s'assurer que l'unité est correctement alimentée, en particuliers à la liaison à la terre.

La source électrique de cet équipement doit posséder une connexion à la terre , ainsi qu'une liaison « neutre » identifiable.

La prise électrique qui alimente l'appareil doit être proche de celle-ci et accessible.

Câble secteur de pays autres que les Etats-Unis L'équipement est livré avec un câble secteur au standard IEC, moulé mâle/femelle.Si vous souhaitez changr la prise mâle de votre cordon, voici les codes couleurs des fils :

Le fil VERT/JAUNE est connecté à T (Terre)Le fil BLEU est connecté à N (Neutre)Le fil MARRON est connecté à P (Phase)

Attention si l'appareil a 2 alimentations, s'assurer que les cordons soient branchés sur la même phase.

Précaution d'emploi :

F

Les procédures de maintenance ne concernentque le service agréé. Afin de réduire le risque de choc électrique, il est recommandé de se limiter aux procédures d'utilisation, à moins d'en être qualifié.Pour toute maintenance, contacter le service compétent.

! ATTENTIONRISQUE DE CHOC ELECTRIQUE

NE PAS RETIRER LE COUVERCLENE PAS INTERVENIR SANSL'AGREMENT DU SERVICE

QUALIFIE

P N

T

N P

T

Connecteur Prise

!

!

Erklärung der SicherheitssymboleDieses Symbol weist den Benutzer auf wichtige Informationen hin, die in der begleitenden Dokumentation enthalten sind.

Dieses Symbol zeigt an, dass gefährliche Spannung vorhanden ist. Es befinden sich keine vom Benutzer zu wartenden Teile im Geräteinneren. Dieses Gerät sollte nur von geschultem Personal gewartet werden

Um das Risiko eines Elektroschocks zu reduzieren, setzen Sie das Gerät weder Regen noch Feuchtigkeit aus.

Stellen Sie immer sicher, dass das Gerät ordnungsgemäß geerdet und verkabelt ist.

Dieses Equipment muss an eine Netzsteckdose mit Schutzleiter angeschlossen werden und einen zuverlässig identifizierbaren Nullleiter haben.

Die Netzsteckdose sollte nahe beim Gerät und einfach zugänglich sein.

Netzanschluss in anderen Ländern als der USADas Equipment wird im Normalfall mit einem Netzkabel mit Standard IEC Anschlussbuchse und einem Standard IEC Anschlussstecker geliefert. Sollten Sie den angeschweißten Stecker auswechseln müssen, entsorgen Sie diesen bitte umgehend. Die farbliche Belegung des Netzkabels ist wie folgt:

GRÜN GELB E = Schutzleiter BLAU N = NulleiterBRAUN L = P = Phase

Achtung: Wenn das Gerät zwei Anschlussbuchsen hat, stellen Sie bitte sicher, dass beide Netzkabel mit der selben Phase in die Netzsteckdose gesteckt werden.

Sicherheits-Warnhinweise

D

!

!

Die angeführten Service-/Reparatur-Anweisungen sind ausschließlich von qualifiziertem Service-Personal auszuführen. Um das Risiko eines lektroschocks zu reduzieren, führen Sie ausschließlich die im Benutzerhandbuch eschriebenen Anweisungen aus, es sei denn, Sie haben die entsprechende Qualifikation. Wenden Sie sich in allen Service-Fragen an qualifiziertes Personal.

! ACHTUNGGefahr von Elektroschocks.

Abdeckungen nicht entfernenKeine vom Benutzer zu wartende Teile

Wenden Sie sich ausschließlichan qualifiziertes Personal

L =Phase

N =Nulleiter

N =Nulleiter

L =Phase

E =Schutzleiter

E =Schutzleiter

Explicación de los Símbolos de SeguridadÉste símbolo refiere al usuario información importante contenida en la literatura incluida. Referirse al manual.

Éste símbolo indica que voltajes peligrosos están presentes en el interior. No hay elementos accesibles al usuario dentro.Esta unidad sólo debería ser tratada por personal cualificado.

Las instrucciones de servicio cuando sean dadas, son sólo para uso de personal cualificado. Para reducir el riesgo de choque eléctrico no llevar a cabo ninguna operación de servicio aparte de las contenidas en las instrucciones de operación, a menos que se esté cualificado para realizarlas. Referir todo el trabajo de servicio a personal cualificado.

Para reducir el riesgo de choque eléctrico, no exponer este equipo a la lluvia o humedad.

Siempre asegurarse de que la unidad está propiamente conectada a tierra y que las conexiones de alimentación están hechas correctamente.

Este equipo debe ser alimentado desde un sistema de alimentación con conexión a TIERRA y teniendo una conexión neutra fácilmente identificable.

La toma de alimentación para la unidad debe ser cercana y fácilmente accesible.

Conexión de alimentación en otros países que no sean USAEl equipo es normalmente entregado con un cable de alimentación con un enchufe hembra estándar IEC en un extremo y con una clavija estándar IEC en el otro. Si se requiere eliminar la clavija para sustituirla por otra, disponer dicha clavija de una forma segura. El código de color a emplear es como sigue:

Advertencia Si la unidad tuviera dos tomas de alimentación, asegurarse de que ambos cables de alimentación están conectados a la misma fase.

ESP

!

!

Advertencias de Seguridad

L N

E

N L

E

ClavijaAerea Macho

EnchufeAereo Hembra

VERDE/ AMARILLO conectado a E (Conductor de protección a Tierra -Earth en el original-)AZUL conectado a N (Conductor Neutro -Neutral en el original-)MARRÓN conectado a L (Conductor Fase -Live en el original-)

RIESGO DE CHOQUE ELECTRICONO QUITAR LAS PROTECCIONNESELEMENTOS NO ACCESIBLES ALUSUARIO.SERVICIO SOLAMENTE A PERSONALCUALIFICADO



Simboli di sicurezza:Questo simbolo indica l'informazione importante contenuta nei manuali appartenenti all'apparecchiatura. Consultare il manuale.

Questo simbolo indica che all'interno dell'apparato sono presenti tensioni pericolose. Non cercare di smontare l'unità. Per qualsiasi tipo di intervento rivolgersi al personale qualificato.

Le istruzioni relative alla manutenzione sono ad uso esclusivo del personale qualificato. E' proibito all'utente eseguire qualsiasi operazione non esplicitamente consentita nelle istruzioni. Per qualsiasi informazione rivolgersi al personale qualificato.

Per prevenire il pericolo di scosse elettriche è necessario non esporre mai l'apparecchiatura alla pioggia o a qualsiasi tipo di umidità.

Assicurarsi sempre, che l'unità sia propriamente messa a terra e che le connessioni elettriche siano eseguite correttamente.

Questo dispositivo deve essere collegato ad un impianto elettrico dotato di un sistema di messa a terra efficace.

La presa di corrente deve essere vicina all'apparecchio e facilmente accessibile.

Connessione elettrica nei paesi diversi dagli Stati UnitiL'apparecchiatura normalmente è spedita con cavo pressofuso con la presa e spina standard IEC. Nel caso della rimozione della spina elettrica, gettarla via immediatamente osservando tutte le precauzioni del caso. La leggenda dei cavi è la seguente:

VERDE/GIALLO cavo connesso ad "E" (terra)BLU cavo connesso ad "N" (neutro)MARRONE cavo connesso ad "L" ( fase)

Attenzione! Nel caso in cui l'apparecchio abbia due prese di corrente, assicurarsi che i cavi non siano collegati a fasi diverse della rete elettrica.

I

!

!

Attenzione:

! ATTENZIONE

L N

E

N L

E

Presa volante Spina volante

RISCHIO DI SHOCK ELETTRICONON CERCARE DI SMONTARE

L'UNITA PER QUALSIASI TIPO DI INTERVENTO RIVOLGERSI AL

PERSONALE QUALIFICATO

Förklaring av SäkerhetssymbolerDenna symbol hänvisar användaren till viktig information som återfinns i litteraturen som medföljer. Se manualen.

Denna symbol indikerar att livsfarlig spänning finns på insidan.Det finns inga servicevänliga delar inne i apparaten. Denna apparat få endast repareras av utbildad personal.

Serviceinstruktioner som anges avser endast kvalificerad och utbildad servicepersonal. För att minska risken för elektrisk stöt, utför ingen annan service än den som återfinns i medföljande driftinstruktionerna, om du ej är behörig. Överlåt all service till kvalificerad personal.

För att reducera risken för elektrisk stöt, utsätt inte apparaten för regn eller fukt.

Se alltid till att apparaten är ordentligt jordad samt att strömtillförseln är korrekt utförd.

Denna apparat måste bli försörjd från ett strömsystem som är försedd med jordadanslutning samt ha en neutral anslutning som lätt identifierbar.

Vägguttaget som strömförsörjer apparaten bör finnas i närheten samt vara lätttillgänglig.

Strömkontakter i länder utanför USAApparaten utrustas normalt med en strömkabel med standard IEC gjuten honkontakt på ena änden samt en standard IEC gjuten hankontakt på den andra änden. Om man måste avlägsna den gjutna hankontkaten, avyttra denna kontakt omedelbart på ett säkert sätt. Färgkoden för ledningen är följande:

GRÖN/GUL ledning ansluten till E (Skyddsjordad ledare)

BLÅ ledning ansluten till N (Neutral ledare)BRUN ledning ansluten till L (Fas ledare)

Varning! Om enheten har två huvudsakliga elförsörjningar, säkerställ att båda strömkablarna som är inkopplade i enheten arbetar från samma fas.

S

! CAUTIONRISK OF ELECTRIC SHOCKDO NOT REMOVE COVERS

NO USER SERVICEABLE PARTSREFER SERVICING TO QUALIFIED

PERSONNEL ONLY

!

!

Säkerhetsvarningar

L N

E

N L

E

Stickkontakt-Hane Stickkontakt-Hona

Forklaring på sikkerhedssymbolerDette symbol gør brugeren opmærksom på vigtig information i den medfølgende manual.

Dette symbol indikerer farlig spænding inden i apparatet. Ingen bruger servicerbare dele i apparatet på brugerniveau. Dette apparat må kun serviceres af faglærte personer..

Serviceinstruktioner er kun til brug for faglærte servicefolk. For at reducere risikoen for elektrisk stød må bruger kun udføre anvisninger i betjeningsmanualen. Al service skal udføres af faglærte personer.

For at reducere risikoen for elektrisk stød må apparatet ikke udsættes for regn eller fugt.

Sørg altid for at apparatet er korrekt tilsluttet og jordet.

Dette apparat skal forbindes til en nettilslutning, der yder BESKYTTENDE JORD og 0 forbindelse skal være tydeligt markeret.

Stikkontakten, som forsyner apparatet, skal være tæt på apparatet og let tilgængelig.

Nettilslutning i andre lande end USAUdstyret leveres normalt med et strømkabel med et standard IEC støbt løst hunstik i den ene ende og et standard IEC støbt hanstik i den anden ende. Hvis et af de støbte stik på strømkablet er defekt, skal det straks kasseres på forsvarlig vis. Farvekoden for lederen er som følger:

GRØN/GUL leder forbundet til J (Jord)BLÅ leder forbundet til 0BRUN leder forbundet til F(Fase)

Forsigtig Hvis enheden har to lysnetindgange, skal der sørges for at begge ledninger tilsluttes lystnetudgange fra den samme fase.

DK

!

!

!

Sikkerhedsadvarsler

! FORSIGTIGRISIKO FOR ELEKTRISK STØD

DÆKPLADER MÅ IKKE FJERNESINGEN BRUGER SERVICERBARE

DELE SERVICE MÅ KUN UDFØRESAF FAGLÆRTE PERSONER

F 0

J

0 F

J

Han-stik Hun-stik

Turvamerkkien selitysTämä merkki tarkoittaa, että laitteen mukana toimitettu kirjallinen materiaali sisältää tärkeitä tietoja. Lue käyttöohje.

Tämä merkki ilmoittaa, että laitteen sisällä on vaarallisen voimakas jännite. Sisäpuolella ei ole mitään osia, joita käyttäjä voisi itse huoltaa. Huollon saa suorittaa vain alan ammattilainen.

Huolto-ohjeet on tarkoitettu ainoastaan alan ammattilaisille. Älä suorita laitteelle muita toimenpiteitä, kuin mitä käyttöohjeissa on neuvottu, ellet ole asiantuntija. Voit saada sähköiskun. Jätä kaikki huoltotoimet ammattilaiselle.

Sähköiskujen välttämiseksi suojaa laite sateelta ja kosteudelta.

Varmistu, että laite on asianmukaisesti maadoitettu ja että sähkökytkennät on tehty oikein.

Laitteelle tehoa syöttävässä järjestelmässä tulee olla SUOJAMAALIITÄNTÄ ja nollaliitännän on oltava luotettavasti tunnistettavissa.

Sähköpistorasian tulee olla laitteen lähellä ja helposti tavoitettavissa.

SähkökytkentäLaitteen vakiovarusteena on sähköjohto, jonka toisessa päässä on muottiin valettu, IEC-standardin mukainen liitäntärasia ja toisessa päässä muottiin valettu, IEC-standardin mukainen pistoliitin. Jos pistoliitin tarvitsee poistaa, se tulee hävittää heti turvallisella tavalla. Johtimet kytketään seuraavasti:

KELTA-VIHREÄ suojamaajohdin E-napaan SININEN nollajohdin N-napaanRUSKEA vaihejohdin L-napaan

Huom! Jos laitteessa on kaksi verkkojännitteen tuloliitäntää, niiden johdot on liitettävä verkkopistorasioihin, joissa on sama vaiheistus.

FI

!

!

Turvaohjeita

!SÄHKÖISKUN VAARA ÄLÄ AVAA

LAITTEEN KANSIA EI SISÄLLÄKÄYTTÄJÄLLE HUOLLETTAVIAOSIA HUOLTO AINOASTAAN

AMMATTILAISEN SUORITTAMANA

VAROITUS

L N

E

N L

E

Pistoliitin Liitäntärasia



Símbolos de SegurançaO símbolo triangular adverte para a necessidade de consultar o manual antes de utilizar o equipamento ou efectuar qualquer ajuste.

Este símbolo indica a presença de voltagens perigosas no interior do equipamento. As peças ou partes existentes no interior do equipamento não necessitam de intervenção, manutenção ou manuseamento por parte do utilizador. Reparações ou outras intervenções devem ser efectuadas apenas por técnicos devidamente habilitados.

As instruções de manutenção fornecidas são para utilização de técnicos qualificados. Para reduzir o risco de choque eléctrico, não devem ser realizadas intervenções no equipamento não especificadas no manual de instalações a menos que seja efectuadas por técnicos habilitados.

Para reduzir o risco de choque eléctrico, não expor este equipamento à chuva ou humidade.

Assegurar que a unidade está sempre devidamente ligada à terra e que as ligações à alimentação estão correctas.

O sistema de alimentação do equipamento deve, por razões de segurança, possuir ligação a terra de protecção e ligação ao NEUTRO devidamente identificada.

A tomada de energia à qual a unidade está ligada deve situar-se na sua proximidade e facilmente acessível.

Ligação da alimentação noutros países que não os EUAO equipamento é, normalmente, enviado com cabo de alimentação com ficha IEC fêmea standard num extremo e uma ficha IEC macho standard no extremo oposto. Se for necessário substituir ou alterar alguma destas fichas, deverá remove-la e elimina-la imediatamente de maneira segura. O código de cor para os condutores é o seguinte:

Condutor VERDE/AMARELO ligado a E (Terra)Condutor AZUL ligado a N (Neutro)Condutor CASTANHO ligado a L (Vivo).

Atenção: Se a unidade tem duas fontes de alimentação assegurar que os dois cabos de alimentação estão ligados a tomadas pertencentes à mesma fase.

P

!

!

Avisos de Segurança

L N

E

N L

E

Ficha Livre Tomada Livre

Power cable supplied for the USA

The equipment is shipped with a power cord with a standard IEC molded free socket on one end and a standard 3-pin plug on the other. If you are required to remove the molded mains supply plug, dispose of the plug immediately in a safe manner. The color code for the cord is as follows:

GREEN lead connected to E (Protective Earth Conductor)

BLACK lead connected to L (Live Conductor)

WHITE lead connected to N (Neutral Conductor)

Note that for equipment that is not fitted with a mains power switch, to comply with EN60950 Clauses 1.7.2 and 2.6.9, the power outlet supplying power to the unit should be close to the unit and easily accessible.

G



Safety Standard The CVR600UD, CVR600BD, CVR600AD, TBS190AD, TBS190BD and TBS190UD conform to the following standards: BS EN60950:2000 Specification for safety of information technology equipment, including electrical business equipment.

UL 1419. Professional video equipment File No. E193966 The CVR600UDV, CVR600BDV, CVR600ADV, TBS190ADV, TBS190BDV and TBS190UDV conform to the following standard: BS EN60950:2000 Specification for safety of information technology equipment, including electrical business equipment.

EMC Standards

These units conform to the following standards: BS EN 55103-1 : 1997 Electromagnetic Compatibility, Product family standard for audio, video, audio-visual and entertainment lighting control apparatus for professional use. Part 1. Emission BS EN 55103-2 : 1997 Electromagnetic Compatibility, Product family standard for audio, video, audio-visual and entertainment lighting control apparatus for professional use. Part 2. Immunity Federal Communications Commission Rules Part 15, Class A :1998 EMC Environment

The product(s) described in this manual conform to the EMC requirements for, and are intended for use in, The controlled EMC environment (for example purpose-built broadcasting or recording studios), and the rural outdoor environment (far away from railways, transmitters, overhead power lines, etc.) E4 EMC Performance of Cables and Connectors

Snell & Wilcox products are designed to meet or exceed the requirements of the appropriate European EMC standards. In order to achieve this performance in real installations it is essential to use cables and connectors with good EMC characteristics. All signal connections (including remote control connections) shall be made with screened cables terminated in connectors having a metal shell. The cable screen shall have a large-area contact with the metal shell. COAXIAL CABLES Coaxial cables connections (particularly serial digital video connections) shall be made with high-quality double-screened coaxial cables such as Belden 1694 or BBC type PSF1/2M. D-TYPE CONNECTORS D-type connectors shall have metal shells making good RF contact with the cable screen. Connectors having "dimples" which improve the contact between the plug and socket shells, are recommended.



About this Manual This manual covers the following products: • CVR600UDV (3598407) • CVR600UD (3598404) • CVR600BDV (3598406) • CVR600BD (3598403) • CVR600ADV (3598405) • CVR600AD (3598402)

• TBS190ADV (3548605) • TBS190AD (3548602) • TBS190BDV (3548606) • TBS190BD (3548603) • TBS190UDV (3548607) • TBS190UD (3548604)

Packing List In addition to the unit ordered please check the contents include an operators manual, rubber feet and power cable. Report any shortages or damage immediately. The unit is supplied in a dedicated packing carton provided by the manufacturer and should not be accepted if delivered in inferior or unauthorized materials. Carefully unpack the carton and check for any shipping damage or shortages. Please retain the box and original packing materials in case the unit needs to be returned. Any shortages or damage should be reported to the supplier immediately. Enclosures:

• Unit ordered • Power cable • Operator's Manual • Rubber feet

The unit can be desk mounted by fitting the rubber feet. A mounting kit to allow either one or two ½ rack boxes to be fitted in a standard 19 inch rack is available separately. The order code is INSY-MNT-KIT. The unit should be placed on a suitable rack shelf and secured to the rack with a mounting kit.

Software Version Amendments Notes about Versions Fitted............... None

Manufacturers Notice Copyright protection claimed includes all forms and matters of copyrightable material and information now allowed by statutory or judicial law or hereinafter granted, including without limitation, material generated from the software programs which are displayed on the screen such as icons, screen display looks etc. Reproduction or disassembly of embedded computer programs or algorithms prohibited. Copyrighted names: Microsoft Windows™ Information in this manual and software are subject to change without notice and does not represent a commitment on the part of Snell & Wilcox Ltd. The software described in this manual is furnished under a license agreement and may not be reproduced or copied in any manner without prior agreement with Snell & Wilcox Ltd. or their authorized agents.



Table of Contents About this Manual ............................................... 6 Packing List.......................................................... 6 Software Version Amendments ......................... 6 Manufacturers Notice.......................................... 6 Table of Contents ................................................ 7 Description........................................................... 9

Front panel views ........................................ 9 Rear panel views......................................... 9 Product Comparison ................................. 10

Installation.......................................................... 11 Power Connections ................................... 11

Supply Voltage................................ 11 Communication Connections .................... 11 4 Way Audio Connector Assembly Details 11 Input Connections ..................................... 12

Separated Y C................................. 12 CVBS-A and CVBS-B ..................... 12 SDI-A & SDI-B................................. 12 AES In – Unbalanced (UD,UDV) .... 12 AES In – Balanced (BD,BDV) ......... 12 Audio In – Balanced (AD,ADV) ....... 12 DV 1394 (ADV,BDV,UDV) .............. 12 Reference Input .............................. 13

Output Connections .................................. 14 Y-C Separated Output .................... 14 CVBS 1 & 2 Out .............................. 14 SDI 1 & 2 Out .................................. 14 AES Out – Unbalanced (UD,UDV) . 14 AES Out – Balanced (BD,BDV) ...... 14 Audio Out - Balanced (AD,ADV)..... 14

Generic Block Diagram ............................. 15 Operation............................................................ 16

Front Panel................................................ 16 Selected items - indication ........................ 17 Default display........................................... 17 Input Options ............................................. 17 DV Interface .............................................. 18 Video Controls........................................... 19

Luma Gain....................................... 19 Chroma Gain................................... 19 Hue.................................................. 19 Black Level:..................................... 19

Genlock ..................................................... 20 More: Additional menu items..................... 21

Freeze ............................................. 21

Pattern............................................. 21 Out 525:........................................... 21 Out 625:........................................... 21 Decoder AGC:................................. 22 Decoder ACC: ................................. 22 Decoder CTI: ................................... 22 Decoder NR: ................................... 22 Comb Filter...................................... 23 Input Std .......................................... 23 In Std NTSC .................................... 23 Encoder ........................................... 23 DV AVC........................................... 23 Default Out ...................................... 23 Display............................................. 23 Preset All ......................................... 24 Net Name ........................................ 24 Serial No.......................................... 24 Version ............................................ 24 About ............................................... 24

Audio: Audio items..................................... 25 Noise: Noise reduction items..................... 26 Enhance: Enhance and ARC items........... 27

Operation via RollCall PC Control Panel......... 29 DV Interface............................................... 29 Input & Output ........................................... 30

Input ................................................ 30 Input Standard................................. 30 Input 525 ......................................... 30 Output Standard.............................. 30 Output 525....................................... 30 Output 625....................................... 30 Pattern............................................. 30 Freeze ............................................. 30 Freeze Style .................................... 30

Proc Amp................................................... 31 Luma Gain....................................... 31 Chroma Gain................................... 31 Black Level ...................................... 31 Hue.................................................. 31

ARC ........................................................... 32 Width ............................................... 32 Height .............................................. 32 Pan .................................................. 32 Tilt.................................................... 32 ARC Presets ................................... 32 ARC Enable..................................... 32

Enhancer ................................................... 33 Y Noise Reduction .......................... 33 Enhance .......................................... 33 V Enhance....................................... 33 Split Screen..................................... 33



Audio ......................................................... 34 Audio Source 1 and 2 ..................... 34 Embedder Group ............................ 34 DV Audio In ..................................... 34 In Level............................................ 34 Out Level......................................... 34

Genlock ..................................................... 35 Mode ............................................... 35 Phase 525 and Phase 625.............. 35

More .......................................................... 36 Decoder........................................... 36 Comb Filter...................................... 36 Encoder........................................... 36 Default Output ................................. 36

Logging & Status ....................................... 37 Logging ........................................... 37 Net Name........................................ 37 Software Version............................. 37 Serial No ......................................... 37 Product............................................ 37 Board ID .......................................... 37

Technical Data ................................................... 38 CVR600UDV SDI, DV & Composite Standards Converter ................................. 39 CVR600UD SDI Composite Standards Converter................................................... 42 CVR600BDV SDI, DV & Composite Standards Converter ................................. 45 CVR600BD SDI & Composite Standards Converter................................................... 48 CVR600ADV SDI, DV & Composite Standards Converter ................................. 51 CVR600AD SDI & Composite Standards Converter................................................... 54 TBS190ADV SDI, DV & Composite synchronizer .............................................. 57 TBS190AD SDI & Composite synchronizer60 TBS190BDV SDI, DV & Composite synchronizer .............................................. 63 TBS190BD SDI & Composite synchronizer66 TBS190UDV SDI, DV & Composite synchronizer .............................................. 69

TBS190UD SDI & Composite synchronizer72 Manual Revision Record................................... 77



Description Front panel views

Rear panel views CVR600UDV/TBS190UDV

CVR600UD/TBS190UD

CVR600BDV/TBS190BDV



Rear Panel Views (continued) CVR600BD/TBS190BD

CVR600ADV/TBS190ADV

CVR600AD/TBS190AD

Product Comparison

Inputs Outputs Product

CVBS Y/C SDI DV AES AnalogAudio CVBS Y/C SDI DV AES Analog

Audio ARC

CVR600UDV 2 1 2 1 2 U/B No 2 1 2 1 2 U/B No Yes

CVR600UD 2 1 2 No 2 U/B No 2 1 2 No 2 U/B No Yes

CVR600BDV 2 1 2 1 2 BAL No 2 1 2 1 2 BAL No Yes

CVR600BD 2 1 2 No 2 BAL No 2 1 2 No 2 BAL No Yes

CVR600ADV 2 1 2 1 No 4 BAL 2 1 2 1 No 4 BAL Yes

CVR600AD 2 1 2 No No 4 BAL 2 1 2 No No 4 BAL Yes

TBS190UDV 2 1 2 1 2 U/B No 2 1 2 1 2 U/B No No

TBS190UD 2 1 2 No 2 U/B No 2 1 2 No 2 U/B No No

TBS190BDV 2 1 2 1 2 BAL No 2 1 2 1 2 BAL No No

TBS190BD 2 1 2 No 2 BAL No 2 1 2 No 2 BAL No No

TBS190ADV 2 1 2 1 No 4 BAL 2 1 2 1 No 4 BAL No

TBS190AD 2 1 2 No No 4 BAL 2 1 2 No No 4 BAL No



Installation Power Connections This is the IEC320 mains power connector suitable for a standard IEC type power. A cable fitted with fused type plug should be used and a fuse rated at 3A installed. Supply Voltage The power supply is auto switching for input voltages in the ranges of 100 V to 240 V nominal. No voltage adjustment procedure is required.

CAUTION: THIS UNIT MUST NOT BE OPERATED WITHOUT

AN EARTH CONNECTION. Power On/Off Switch There is no power On/Off switch. Power ON will be indicated by the illumination of the front panel display. Note that for equipment that is not fitted with a mains power switch, to comply with EN60950 Clauses 1.7.2 and 2.6.9, the power outlet supplying power to the unit should be close to the unit and easily accessible. Communication Connections

This is the USB connection. This can be used to remotely control the unit via Rollcall. A software application is provided for this. 4 Way Audio Connector Assembly Details Cable used for screw terminals should equal or exceed Belden 1800B specifications for full performance and the wire tails MUST be as short as possible and be assembled as shown opposite.

Red

Tie Wrap

ReturnBlack



Input Connections (Where applicable) Separated Y C The Y-C (S-VHS/Hi-8) input signal is connected to the unit via a 4 pin Mini DIN type connector. Y input level is a nominal 1V p-p into 75 Ohms C input level is a nominal 0.3V p-p color burst into 75 Ohms. CVBS-A and CVBS-B These are the 2 Composite video inputs to the unit via BNC connectors. Nominal input level is 1 V p-p terminated in 75 Ohms. SDI-A & SDI-B These are the two SDI inputs to the unit via BNC connectors. AES In – Unbalanced (UD,UDV) These are the two AES inputs to the unit via BNC connectors. AES In – Balanced (BD,BDV) These are the two AES inputs to the unit via 3 pin connectors.

CAUTION: STATIC SENSITIVE PINS Audio In – Balanced (AD,ADV) These are the two analog audio inputs to the unit via 3 pin connectors.

CAUTION: STATIC SENSITIVE PINS DV 1394 (ADV,BDV,UDV) This is the 4 pin DV I/O connector. This interface will deal with one pair of 32, 44.1 or 48kHz audio. Note that this unit does not simultaneously decode and encode.



Reference Input When suitable signals are connected to this input, the video output of the unit will be synchronized to the reference signal source when the genlock function is selected. If no signal is present the unit will automatically revert to internal free-running operation. BNC loop-through connectors are provided and the signal may be black burst or composite video at standard level.



Output Connections (Where applicable) Y-C Separated Output A Y-C (S-VHS/Hi-8) output signal is available from a 4 pin Mini DIN type connector. Y output level is a nominal 1V p-p into 75 Ohms C output level is a nominal 0.3V p-p color burst into 75 Ohms. CVBS 1 & 2 Out Two composite outputs are available from these BNC connectors. Output level is standard 1V p-p into 75 Ohms. SDI 1 & 2 Out These are the two SDI outputs of the unit via BNC connectors. AES Out – Unbalanced (UD,UDV) These are the two AES outputs of the unit via BNC connectors. AES Out – Balanced (BD,BDV) These are the two AES outputs of the unit via 3 pin connectors.

CAUTION: STATIC SENSITIVE PINS Audio Out - Balanced (AD,ADV) These are the two analog audio outputs of the unit via 3 pin connectors.

CAUTION: STATIC SENSITIVE PINS



Generic Block Diagram

Video synchroniser /

converter

Delay

Tracking

Audio embed

SDI Audio extract

SDI BSDI A

ADCLeft B

Right B

SDI

CompositeEncoder

DACLeft 1Right 1

AES RxAES A AES Tx AES 1

Analog Audio option

Additional delay

DV DV Encode

Audio

DV

ADCLeft A

Right A

AES RxAES B

2

1B A

AES Tx AES 2

Audio SourceSelect

DACLeft 2Right 2

AES Audio option

Comb Decoder

Noise Reducer

YC

Composite

SDI

Processed Pair 1Processed Pair 2

Source

Source

HANC Passthrough

DV Audio SourceSelect

Composite A

YC

Composite B

DV Decode

Audio



Operation The layout of the active front panel is shown below. Applying power activates the unit; if it was powered down in standby mode, switch on using the standby button. Direct access functions are available via six buttons. The action of the control knob and function selection buttons is indicated by the display and varies depending upon the mode selected. Front Panel

Item Description

Standby When the unit is switched off the LED is illuminated. When the unit is switched on the display and controls are active and the LED is extinguished.

Display Provides status and control information Control knob Rotate to scroll through functions

Function selection button A

This button has two functions 1. This button toggles between the default screen (showing the status of the input, output and genlock) and the Input selection screen. 2. When the word ‘Back’ is shown on the display adjacent to this button, pressing it returns to the previous menu.

Function selection button B

The button has three functions 1. This selects the Output selection screen. 2. When the word ‘Select’ is shown on the display adjacent to this

button, pressing it selects the desired user selection 3. When the word ‘Preset’ is shown on the display adjacent to this

button, pressing it presets the chosen control.

Video This selects luminance gain for adjustment and repeat presses scrolls through the additional controls

Audio This selects the Audio options Genlock Display the genlock options

Noise This displays the noise reduction options Enhance This displays the enhance and ARC options

More… This allows all major selections to be displayed using the knob to scroll through the items.

Standby

Direct access functions

Direct access functions

Function selection button A Control knob

Function selection button B

Display



Selected items - indication Selected items are highlighted with a – sign at the beginning and end of the name. Default display The product defaults to show the state of the input, output and current genlock status.

Upper Soft Button This will allow the input signal type to be selected. Input Options

CVR600D TBS190D

CVR600DV TBS190DV

CVBS A CVBS A CVBS B CVBS B YC YC SDI B SDI A SDI A SDI B DV PAL DV NTSC

The selected input is indicated by – signs at either end of the name. Rotate the knob to show alternative inputs and then press Select. Note that for this and most other menus: To return to the default menu press Back or wait for the time out.

Lower Soft Button This will allow the line standard of the output signal to be selected. Using the knob either 625 or 525 may be chosen.

In: CVBS A No Input Out: PAL No Ref

Back Input Select -CVBS A-

Back Output Select -625-



DV Interface Using the DV interface with a PC the following procedure must be followed 1. Power on the TBS/CVR, and ensure the

standard is correct 2. Ensure that the DV application software is

shut. 3. Connect the DV lead to the PC. 4. Load up DV application software. It is then

possible to capture and play back via the TBS/CVR in 525 or 625.

5. Note that the standard cannot be changed

without disconnecting the lead and re-loading the DV application software.

Using the DV Interface with other DV devices Ensure the device to be connected to the TBS/CVR is powered before connecting to the TBS/CVR. In some cases this is not necessary. If the unit is powered up with the lead connected and it doesn't work, disconnect the lead and reconnect it. Connecting two TBS/CVR devices together When using DV it is essential that both units are powered before connecting the lead. If this isn’t done it is possible that the DV interface will lock out. To restore operation, power off both units, remove the lead, power on and reconnect.



Video Video Controls Luma Gain Press the Video Gain button to select Luma Gain. Rotate the knob to adjust the Luma Gain by +6dB in 0.1dB steps. Preset will return the Luma Gain to 0dB. Chroma Gain Press the Video Gain button for a second time to select Chroma Gain. Rotate the knob to adjust the Chroma Gain by +6dB in 0.1dB steps. Preset will return the Chroma Gain to 0dB. Hue Press the Video Gain button for a third time to select Hue. Rotate the knob to adjust the Hue by +30o in 1o steps. Preset will return the Hue to 0o. Black Level: Rotate the knob to adjust the Black Level by +100mV in 0.8mV steps. Preset will return the Black Level to 0mV.

Back Luma Gain Select 1.1dB

Back Chroma Gain Select 2.1dB

Back Hue Select 1°

Back Black Level Select 1.6mV



Genlock Genlock The selected output is indicated by – signs at either end of the name. Rotate the knob to show the alternative Genlock modes (Ref Lock, Input Lock, Float, Freerun) and then press Select. Repeated presses of the Genlock button will move through the following menus. Gen Coarse 525: in 0.999µs steps Gen Fine 525: in 0.037µs steps Gen Coarse 625:in 0.999µs steps Gen Fine 625: in 0.037µs steps Genlock Modes Ref Lock Output video is locked to an external reference. The offset between the external reference and the output can be adjusted over a range of approximately +/- 3 lines using the Gen Coarse and Gen Fine controls Input Lock Output video, if the same line standard, is locked to the selected input video source. When converting between line standards this mode is not available. Float In this stabilized or ‘floating mode’ the output will always follow shortly after the input, so preventing lip-sync errors and frame drop / repeat. When converting between line standards this mode is not available. Freerun Output video is locked to an internal reference clock.

Back Genlock Select -Freerun-



More More: Additional menu items The More menu enables further menus to be accessed. Rotate the knob to the desired function then press select. Note that the text in the upper right hand area of the display shows the previous function and the text in the lower right hand area shows the next function. Freeze Press the lower soft button to show the Enable/Disable the picture freeze function. Note that the unit does not time out with the freeze function. Use the back button. Freeze Style This allows the style of freeze to be selected. Press the lower soft button to select either Frame or Field freeze (only field freeze performed whilst standards converting). Pattern Press select to show the Pattern menu. Rotate the knob to show the Off, Color bars or Black options then press select. Out 525: This allows the composite 525 standard output type to be selected. Press select, then rotate the knob to show the NTSC, NTSC-J or PALM output video options then press select again. Out 625: This allows the composite 625 standard output type to be selected. Press select, then rotate the knob to show the PAL or PALN output video options then press select.

Back Freeze Select Freeze Style

Back Freeze Freeze Style Select Pattern

Back Freeze Style Frame Field

Previous Function

Back Freeze Style Pattern Select Out 525

Next Function

Back Pattern Out 525 Select Out 625

Back Out 525 Out 525 Select Decoder AGC



Decoder AGC: The automatic gain control (AGC) function examines the input sync level and adjusts the luminance and chrominance gain to compensate for overall signal level attenuation. Use this control when the input video signal levels are low and automatic correction is desired. Press the lower soft button to Enable and Disable the Decoder AGC function. Decoder ACC: The automatic color gain control (ACC) function examines the input burst amplitude and adjusts chrominance gain to compensate for chroma level attenuation. Use this control when chroma levels are low compared to luminance. This may occur when using YC installations or composite from RF links. Press the lower soft button to Enable and Disable the Decoder ACC function. Decoder CTI: The chroma transient improvement (CTI) control examines the input video data. It detects transitions of chroma and enhances chroma edges in order to artificially restore lost color bandwidth. Use this function when the input video has chroma bandwidth limitations. Press the lower soft button to Enable and Disable the Decoder CTI function. Decoder NR: The digital noise reduction is based on the assumption that high frequency signals with low amplitude are probably noise and their removal improves picture quality. Improvements can be seen on most material so this function is on by default. Press the lower soft button to Enable and Disable the Decoder NR function.

Back Pattern Decoder AGC Select Out 625

Back Decoder AGC Decoder ACC Select Decoder CTI

Back Decoder ACC Decoder CTI Select Decoder NR

Back Decoder CTI Decoder CNR Select Comb Filter



Comb Filter The comb filter employs a 5-line adaptive 2D-comb filter that separates chrominance and luminance when decoding a composite video signal. It adapts to the video standard and signal quality automatically. This control improves the decoder performance and should only be switched off if the operator needs to see the source through only a low pass filter. Press the lower soft button to Enable and Disable the Decoder NR function. Input Std Rotate the knob to show the Auto, PAL, NTSC, SECAM, PALM, PALN or N443 input video option. Choose the forced composite standard or automatic detection by pressing select. In Std NTSC Rotate the knob to show the NTSC or NTSC-J input video options then press select. NTSC-J is similar to NTSC but without a pedestal Encoder Rotate the knob to show the Full Bandwidth, Luma Low Pass or Luma Notch encoder options then press select. DV AVC Rotate the knob to desired AVC command [stop, play, record, forward, rewind], then press select. Default Out Rotate the knob to show the Pattern, Black or Input default output video options then press select. Display Rotate the knob to adjust the display brightness between 25% and 100%. Preset will return the display brightness to 75%.

Back Decoder NR Comb Filter Select Input Std

Back Comb Filter Input Std Select In Std NTSC

Back Input Std In Std NTSC Select Encoder

Back In Std NTSC Encoder Select Default Out

Back DV AVC Default Out Select Display

Back Default Out Display Select Preset All

Back Encoder DV AVC Select Default Out



Preset All Press select to preset the unit. Net Name Indicates the network name of the unit. Serial No Indicates the serial number of the unit. Version Indicates the software version number of the unit. About The about screen shows information about the unit.

Snell & Wilcox

Back Preset All Net Name Select Serial No

Back Net Name Serial No Select Version

Back Serial No Version Select About

Back Version About Select

Back Display Preset All Select Net Name



Audio Audio: Audio items The Audio menu enables further menus to be accessed. Rotate the knob to the desired function then press select. Rotate the knob to show the alternative audio sources and then press Select. The selected parameter is indicated by – signs at either end of the name. Repeated presses of the Audio button will move through the following menus. Audio Source 1 and 2 Rotating the knob will show the selections available for Source 1 and 2. These are: SDI Pairs 1 to 8 AES Pair A or B DV/1394 Embedder Group This selects the destination Embedder Group. These are: Disable Group 1 to 4 DV Audio In This selects the pair from the DV input to be selected for processing. These are: Select either Process Pair 1 or Process Pair 2. Delay Coarse This sets the Audio delay. The range of control is from 0 to 2500 ms in 100 ms steps. Delay (Fine) This sets the Audio delay. The range of control is from 0 to 2500 ms in 1 ms steps. Note that the total delay time will be the addition of the two delay control settings up to a combined maximum of 2500 ms. DV Out Mode The DV audio output resolution may be selected from the list: 48k/16 bit 44.1k/16 bit 32k/16 bit 32k/12 bit

Back Audio Source 1 Select -SDI Pair1-

Back Embedder Group Select -Group 2-

Back DV Audio In Select Process Pair 1

Back Delay Coarse Preset 405ms

Back Delay Preset 405ms

DV Out Mode Select -48k/16bit-



Noise Noise: Noise reduction items The Noise menu enables further menus to be accessed. Rotate the knob to the desired function then press select. Rotate the knob to show the alternative audio sources and then press Select. The selected parameter is indicated by – signs at either end of the name. Repeated presses of the Noise button will move through the following menus. Y Noise Red This allows the amount of luminance noise reduction to be set. Selections are as follows: Off........No noise reduction applied 1, 2, 3...Increasing levels of noise reduction applied. Max......Maximum level of noise reduction applied. C Noise Red This allows the amount of chrominance noise reduction to be set. Selections are as follows: Off........No noise reduction applied 1, 2, 3...Increasing levels of noise reduction applied. Max......Maximum level of noise reduction applied. Split Screen The screen may be split to show the picture before and after noise reduction. This function may be set to Disable (On) or Enable (Off).

Back Y Noise Red Select -Off-

Back C Noise Red Select -Off-

Back Split Screen Enable Off



Enhance Enhance: Enhance and ARC items The Enhance menu enables further menus to be accessed. Rotate the knob to the desired function then press select. Rotate the knob to show the alternative audio sources and then press Select. The selected parameter is indicated by – signs at either end of the name. Repeated presses of the Enhance button will move through the following menus. Enhance This allows horizontal enhancement to be applied to the picture. Selections are as follows: -2, -1, 0, +1, +2, +3 V Enhance This allows vertical enhancement to be applied to the picture. Selections are as follows: 0, +1, +2, +3 ARC Enable This allows the Aspect Ratio Conversion functions to be enabled or disabled. ARC Presets This allows preset values of Aspect Ratio Conversion to be selected. Values are as follows: Normal (no change) 4:3>16:9PB 4:3>14:9PB 4:3>16:9FH 16:9LB>4:3 16:9LB>14:9LB 16:9FH>4:3 16:9FH>14:9LB 16:9FH>4:3LB

Back Enhance Preset 0

Back VEnhance Preset 0

Back ARC Enable Enable Off

Back ARC Presets Select Normal



Enhance (continued) H Size This allows the horizontal size of the picture to be adjusted. The range of control is from 50% to 200% in 0.5% steps. V size This allows the vertical size of the picture to be adjusted. The range of control is from 50% to 200% in 0.5% steps. H Pan This allows the picture to be panned from left to right. The range of control is ±360 input pixels in 1 pixel steps. V Tilt This allows the picture to be panned from top to bottom. The range of control is ±150 input field lines in 1 line steps.

Back HPan Preset 0

Back VTilt Preset 0

Back Hsize Preset 100%

Back Vsize Preset 100%



Operation via RollCall PC Control Panel DV Interface Using the DV interface with a PC the following procedure must be followed 1. Power on the TBS/CVR, and ensure the

standard is correct 2. Ensure that the DV application software is

shut. 3. Connect the DV lead to the PC. 4. Load up DV application software. It is then

possible to capture and play back via the TBS/CVR in 525 or 625.

5. Note that the standard cannot be changed

without disconnecting the lead and re-loading the DV application software.

Using the DV Interface with other DV devices Ensure the device to be connected to the TBS/CVR is powered before connecting to the TBS/CVR. In some cases this is not necessary. If the unit is powered up with the lead connected and it doesn't work, disconnect the lead and reconnect it. Connecting two TBS/CVR devices together When using DV it is essential that both units are powered before connecting the lead. If this isn’t done it is possible that the DV interface will lock out. To restore operation, power off both units, remove the lead, power on and reconnect.



Input & Output

Input This will allow the input signal type to be selected.

CVR600D & TBS190D

CVR600DV & TBS190DV

CVBS A CVBS A CVBS B CVBS B YC YC SDI B SDI A SDI A SDI B DV PAL DV NTSC

Input Standard This allows the unit to detect selected input standards. Any of the listed standards may be selected. If Auto is selected the unit will detect all the listed standards. Input 525 For 525 line standards this allows either pure NTSC or NTSC-J standards to be detected. Output Standard (CVR versions only) This allows the output line standard to be selected. Output 525 This allows the composite 525 standard output type to be selected. Output 625 This allows the composite 625 standard output type to be selected. Pattern This allows a output signal to become either a Pattern or a Black signal.

Freeze When selected the output will become a frozen picture. Freeze Style This allows the style of freeze to be selected. Either freeze Field or Frame freeze may be selected.



Proc Amp This allows adjustments to be made to the video signal. Note that for this and other screens the following applies to the scroll bars:

The and symbols at the ends of the scroll bar allow the value to be adjusted in discrete steps. The numerical value will be shown next to the

scroll bars and selecting Preset will return the setting to the calibrated value for that item. Luma Gain This allows the luminance gain (Y) to be adjusted. Adjustment range is +6dB in 0.1dB steps. Preset will return the Luma Gain to 0.0dB. Chroma Gain This allows the chrominance gain (C) to be adjusted. Adjustment range is +6dB in 0.1dB steps. Preset will return the chrominance Gain to 0.0dB.

Black Level This allows the black level to be adjusted. Adjustment range is +100 mV in 0.08 mV steps. Preset will return the black level to 0.0 mV. Hue This allows the hue to be adjusted. Adjustment range is +30o in 1o steps. Preset will return the Hue to 0 Deg.



ARC

This allows the Aspect Ratio Conversion functions to be setup.

Width This allows the horizontal size of the picture to be adjusted. The range of control is from 50% to 200% in 0.5% steps. Height This allows the vertical size of the picture to be adjusted. The range of control is from 50% to 200% in 0.5% steps. Pan This allows the picture to be panned from left to right. The range of control is ±360 input pixels in 1 pixel steps. Tilt This allows the picture to be panned from top to bottom. The range of control is ±150 input field lines in 1 line steps. ARC Presets This allows preset values of Aspect Ratio Conversion to be selected. Values are as follows: • Normal (no change) • 4:3>16:9PB • 4:3>14:9PB • 4:3>16:9FH • 16:9LB>4:3 • 16:9LB>14:9LB • 16:9FH>4:3 • 16:9FH>14:9LB • 16:9FH>4:3LB ARC Enable This allows the Aspect Ratio Conversion functions to be enabled (selected) or disabled.



Enhancer

This screen allows various types of enhancement to be applied to the processed signal. Y Noise Reduction This allows the amount of luminance noise reduction to be set. Selections are as follows: Off........No noise reduction applied 1, 2, 3...Increasing levels of noise reduction applied. Max......Maximum level of noise reduction applied. C Noise Reducer This allows the amount of chrominance noise reduction to be set. Selections are as follows: Off........No noise reduction applied 1, 2, 3...Increasing levels of noise reduction applied. Max......Maximum level of noise reduction applied.

Enhance This allows horizontal enhancement to be applied to the picture. The adjustment range is: -2, -1, 0, +1, +2, +3

V Enhance This allows vertical enhancement to be applied to the picture. The adjustment range is: 0, +1, +2, +3 Split Screen The screen may be split to show the picture before and after noise reduction when this function is checked.



Audio

Audio Source 1 and 2 This allows the signal for Audio Source 1 and 2 to be chosen. Selections are: SDI Pairs 1 to 8

AES Pair A or B

DV/1394

Embedder Group This allows the destination Embedder Group to be chosen. Selections are: Disable

Group 1 to 4

DV Audio In This selects the pair from the DV input to be selected for processing. Selections are: Process Pair 1

Process Pair 2.

Delay This sets the Audio delay. The range of control is from 0 to 2500 ms in 1 ms steps.

In Level (Analog Audio I/O versions only) This sets the input level for 0 dB FS. The range of control is from +24 to +12 dBu in steps of 0.5 dB. Default is to +18 dBu. Out Level (Analog Audio I/O versions only) This sets the output level from 0 dB FS. The range of control is from +24 to +12 dBu in steps of 0.5 dB. Default is to +18 dBu.



Genlock This screen allows the genlock functions to be setup. Mode This allows the mode of genlocking to be selected. Ref Lock Output video is locked to an external reference. The offset between the external reference and the output can be adjusted over a range of approximately +/- 3 lines using the Phase controls Input Lock Output video, if the same line standard, is locked to the selected input video source. When converting between line standards this mode is not available. Float In this stabilized or ‘floating mode’ the output will always follow shortly after the input, so preventing lip-sync errors and frame drop / repeat. When converting between line standards this mode is not available. Free Run Output video is locked to an internal reference clock. Phase 525 and Phase 625 These control allows the offset between the external reference and the output to be adjusted over a range of approximately ±1 line of the operating standard.



More

This screen allows various functions to be setup.

Decoder Settings for the decoder may be selected with function. AGC The automatic gain control (AGC) function examines the input sync level and adjusts the luminance and chrominance gain to compensate for overall signal level attenuation. Check this control when the input video signal levels are low and automatic correction is desired. ACC The automatic color gain control (ACC) function examines the input burst amplitude and adjusts chrominance gain to compensate for chroma level attenuation. Check this control when chroma levels are low compared to luminance. This may occur when using YC installations or composite from RF links. CTI The chroma transient improvement (CTI) control examines the input video data. It detects transitions of chroma and enhances chroma edges in order to artificially restore lost color bandwidth. Use this function when the input video has chroma bandwidth limitations. Decoder NR: The digital noise reduction is based on the assumption that high frequency signals with low amplitude are probably noise and their removal improves picture quality. Improvements can be seen on most material so this function is on by default. Comb Filter The comb filter employs a 5-line adaptive 2D-comb filter that separates chrominance and luminance when decoding a composite video signal. It adapts to the video standard and signal quality automatically. This control improves the decoder performance and should only be switched off if the operator needs to see the source through only a low pass filter.

Encoder This allows the type filtering for the luminance signal of the encoder to be selected. Default Output When the input signal is lost this allows a signal to be chosen to become the output signal.



Logging & Status

Logging Information about various parameters can be made available to a logging device that is attached to the RollCall™ network. Any of the items may be selected. Net Name This will show the network name of the unit. To change the name, type the new name in the text area and then select (return). Selecting Preset will return the text to the default name. Software Version This will show the software version number of the unit. Serial No This will show the serial number of the unit. Product This shows the product type Board ID This shows the board ID



Technical Data

CVR600UDV SDI, DV & Composite Standards Converter .................................................................39

CVR600UD SDI &Composite Standards Converter ...........................................................................42

CVR600BDV SDI, DV & Composite Standards Converter .................................................................45

CVR600BD SDI & Composite Standards Converter...........................................................................48

CVR600ADV SDI, DV & Composite Standards Converter .................................................................51

CVR600AD SDI & Composite Standards Converter...........................................................................54

TBS190ADV SDI, DV & Composite synchronizer...............................................................................57

TBS190AD SDI & Composite synchronizer ........................................................................................60

TBS190BDV SDI, DV & Composite synchronizer...............................................................................63

TBS190BD SDI & Composite synchronizer ........................................................................................66

TBS190UDV SDI, DV & Composite synchronizer...............................................................................69

TBS190UD SDI & Composite synchronizer ........................................................................................72



CVR600UDV SDI, DV & Composite Standards Converter Broadcast quality standards converter and synchronizer with AES and embedded audio The CVR600UDV is a multi-standard broadcast quality 12-bit sampling, 10-bit processing standards converter, synchronizer, aspect ratio converter, noise reducer and time base stabilizer with SDI, DV, composite and YC interfaces. Standards conversion between 525 and 625 line standards (NTSC/PAL) employs a powerful 20 point, 4-field, 5-line interpolation aperture to give smooth motion and maximum vertical resolution. Embedded audio is processed as well as providing unbalanced AES audio interfaces

Audio

Video Processing

Standards ConverterSynchronizer

Time Base StabilizerAspect Ratio Conversion

Noise ReducerEnhancer

2 x CompositeVideo

1 x Y/C(miniDIN4)

Analog

Digital

2 x SDIwith embedded

audio

DVwith audio

(1394 4pin)

2 x AESUnbalanced

Audio Processing

Channel SelectionDelay

SDI Embeddedand DV audio

CompositeVideo

Y/C(miniDIN4)

Digital

SDIwith embedded

audio

DVwith audio

(1394 4pin)

Audio

Analog

2 x AESUnbalanced

Rollcall Control &Monitoring

Reference(loop-through)

Reference

USB



Features • Standards Converter & Aspect ratio

converter • Synchronization & time base stabilization • ARC with presets and size controls • Adaptive recursive Noise Reduction with

automatic noise level detection • 20 point vertical-temporal aperture • 12-bit decoding with 5-line comb filter • 12-bit encoding • Inputs PAL, NTSC, NTSC-J, NTSC4.4,

PAL-N, PAL-M, SECAM with automatic input detection

• Outputs PAL, NTSC, NTSC-J, PAL-N, PAL-M

• 4 channel (2 pair) embedded audio processing

• Seamless PCM audio tracking delay with manual offset – up to 2.5s

• Pass through for all HANC/VANC data in synchronize mode

• Options for balanced / unbalanced AES and balanced analogue interfaces

• Unique genlock 'Floating mode*' • Composite inputs tolerant to noise &

errors • Video gain, black level, chroma gain,

NTSC hue • RollCall compatible via USB link • Compact ½ rack width with optional rack

mount kit. Low power (no fan)

Applications • Universal Analog / Digital interface • Audio embedding & extraction • Satellite down-link & radio links • Ingest / PC capture pre-processing • Duplication • VHS dubbing • Format conversion

Inputs and Outputs

Video Input

2 x SDI ................................525/625 line with automatic detection (BNC)

2 x Composite .....................27MHz, 12-bit sampling PAL, NTSC, NTSC-J, NTSC4.4, PAL-N, PAL-M, SECAM with automatic detection (BNC)

1 x YC .................................27MHz, 12-bit sampling PAL, NTSC, NTSC-J, NTSC4.4, PAL-N, PAL-M with automatic detection (Mini DIN4)

Reference ...........................Composite or Y (BNC loop-through)

Video Output

2 x SDI ................................525/625 line (BNC)

2 x Composite* ...................27MHz, 12-bit D to A. Output Formats PAL, NTSC, NTSC-J, PAL-N, PAL-M (BNC)

1 x YC* ................................27MHz, 12-bit D to A. Output Formats PAL, NTSC, NTSC-J, PAL-N, PAL-M (Mini DIN4)

* No SCH lock

Video Input/Output

1 x DV .................................4 pin DV connector. (will not simultaneously decode and encode) with 32, 44.1 or 48kHz audio – one pair

Audio Options

2 x AES input ......................Unbalanced (BNC) 32-96kHz PCM audio

2 x AES output ...................Unbalanced (BNC) 48kHz PCM audio

Remote control ..................RollCall via USB link to a PC



Control Features

Input Select .........................SDI A,B; DV; Composite A, B; YC

Output Standard..................525; 625

Audio Source (1) .................SDI pair 1-8; DV; External 1-2


Audio Destination................SDI group 1-4

DV Audio Encode................From processed pair 1-2

Add Audio Delay .................0ms to +2.5s

Analogue Audio Level .........+12 to +24dBu (in / out)

Noise Reduction..................Y;C (Off; 1; 2; 3; Max)

Split Screen.........................Off/On (view noise reduction)

Vertical Enhance.................Off; 1; 2; 3 (max)

Horizontal Enhance.............-2; -1; 0; 1; 2; 3 (max)

ARC Enable ........................Off/On

ARC H Size .........................50% to 200% (0.5% steps)

ARC V Size .........................50% to 200% (0.5% steps)

ARC H Pan..........................+360 to –360 input pixels

ARC V Tilt ...........................+ 150 to –150 input field lines

ARC Presets .......................Normal; 8 fixed presets

Input Standard NTSC .........NTSC, NTSC-J

Composite Output ...............PAL, NTSC, NTSC-J, PAL-N, PAL-M (Not sub-carrier locked)

Freeze .................................Freezes next frame (sync mode)

Field Freeze ........................Freezes next field

Luminance Gain ..................Preset; ± 6dB

Chrominance Gain ..............Preset; ± 6dB

Black Level..........................Preset; ± 100mV

NTSC Hue...........................Preset; ± 30 degrees

Genlock Phase....................Preset; approx. ±1 line

Genlock Mode .....................Lock to reference; Lock to input; Float (stabilized) - if same line standard; Free-run

Output Pattern.....................Black; Color Bars

Default Output .....................When input is lost; go to black; go to color bars

Decoder / Encoder ..............AGC, ACC, comb, DNR, CTI

DV features .........................Audio sample rate; AVC (play/record/stop/forward/rewind)

Indication / Monitoring

Input Standard.....................Present; Standard

Reference ...........................Present; Error (Error indicated if the reference is not the same line standard as the input)

Power ..................................Standby

Rollcall

All Control features available from RollCall via PC USBshare application.

Indication/monitoring parameters are available for Logging and RollTrack

System Parameters

Processing ......................... ≥10 bit

Conversion Aperture ...........4 field / 5 line

SDI Input Switch..................Tolerant to SMPTE RP168 vertical interval switch.

SDI HANC Data ..................All data passed when input & output are the same standard, except data group being embedded

Vertical Interval ..................All luminance data passed when input & output are the same standard

Reference Lock Range .......Greater than ±80ppm

Mechanical

Dimensions .........................½ 1RU rack (44x220x250mm)

Temperature........................0°C to 35 °C operating -20 °C to +70 °C storage

* Floating Mode - Without a reference the output will either free-run or lock to a stabilized input sync if operating in synchronize mode. In this stabilized or ‘floating mode’ the output will always follow shortly after the input, so preventing lip-sync errors and frame drop / repeat. The inputs are highly tolerant to unstable and noisy sources, while the synchronizer always creates correctly aligned images, even during sync disturbances and asynchronous input switches.

Full Product List Base Model Kudos Plus CVR600UDV (3598407) The CVR600UDV is a multi-standard broadcast quality synchronizer, noise reducer and time base stabilizer with SDI, DV, composite and YC interfaces, 12 bit sampling and 10 bit processing featuring embedded and unbalanced AES audio. Base Model Kudos Plus CVR600UDV (3598407-RM) As above, with rack mount kit Option Rack mount kit (INSY-MNT-KIT) Rack mount kit to mount one or two units in a 19” rack



CVR600UD SDI Composite Standards Converter Broadcast quality standards converter and synchronizer with AES and embedded audio The CVR600UD is a multi-standard broadcast quality 12-bit sampling, 10-bit processing standards converter, synchronizer, aspect ratio converter, noise reducer and time base stabilizer with SDI, composite and YC interfaces. Standards conversion between 525 and 625 line standards (NTSC/PAL) employs a powerful 20 point, 4-field, 5-line interpolation aperture to give smooth motion and maximum vertical resolution. Embedded audio is processed as well as providing unbalanced AES audio interfaces

Audio

Video Processing




2 x CompositeVideo

1 x Y/C(miniDIN4)

Analog

Digital


audio

2 x AESUnbalanced

Audio Processing


SDI Embeddedaudio

CompositeVideo

Y/C(miniDIN4)

Digital

SDIwith embedded

audio

Audio

Analog

2 x AESUnbalanced



Reference

USB




converter • Synchronization & time base stabilization • ARC with presets and size controls • Adaptive recursive Noise Reduction with

automatic noise level detection • 20 point vertical-temporal aperture • 12-bit decoding with 5-line comb filter • 12-bit encoding • Inputs PAL, NTSC, NTSC-J, NTSC4.4,







• Unique genlock 'Floating mode*' • Composite inputs tolerant to noise &

errors • Video gain, black level, chroma gain,

NTSC hue • RollCall compatible via USB link • Compact ½ rack width with optional rack

mount kit. Low power (no fan)


Inputs and Outputs

Video Input





Video Output

2 x SDI ................................525/625 line (BNC)



* No SCH lock

Audio Options






Control Features

Input Select .........................SDI A,B; Composite A, B; YC

Output Standard..................525; 625

Audio Source (1) .................SDI pair 1-8; External 1-2









ARC Enable ........................Off/On







Composite Output ...............PAL, NTSC, NTSC-J, PAL-N, PAL-M















Power ..................................Standby

Rollcall



System Parameters

Processing ......................... ≥10 bit






Mechanical



• Floating Mode - Without a reference the output will either free-run or lock to a stabilized input sync if operating in synchronize mode. In this stabilized or ‘floating mode’ the output will always follow shortly after the input, so preventing lip-sync errors and frame drop / repeat. The inputs are highly tolerant to unstable and noisy sources, while the synchronizer always creates correctly aligned images, even during sync disturbances and asynchronous input switches.

Full Product List Base Model Kudos Plus CVR600UD (3598404) The CVR600UD is a multi-standard broadcast quality synchronizer, noise reducer and time base stabilizer with SDI, composite and YC interfaces, 12 bit sampling and 10 bit processing featuring embedded and unbalanced AES audio Base Model Kudos Plus CVR600UD (3598404-RM) As above, with rack mount kit Option Rack mount kit (INSY-MNT-KIT) Rack mount kit to mount one or two units in a 19” rack



CVR600BDV SDI, DV & Composite Standards Converter Broadcast quality standards converter and synchronizer with AES and embedded audio The CVR600BDV is a multi-standard broadcast quality 12-bit sampling, 10-bit processing standards converter, synchronizer, aspect ratio converter, noise reducer and time base stabilizer with SDI, DV, composite and YC interfaces. Standards conversion between 525 and 625 line standards (NTSC/PAL) employs a powerful 20 point, 4-field, 5-line interpolation aperture to give smooth motion and maximum vertical resolution. Embedded audio is processed as well as providing balanced AES audio interfaces

Audio

Video Processing




2 x CompositeVideo

1 x Y/C(miniDIN4)

Analog

Digital


audio

DVwith audio

(1394 4pin)

2 x AESBalanced

(screw terminal)

Audio Processing



CompositeVideo

Y/C(miniDIN4)

Digital

SDIwith embedded

audio

DVwith audio

(1394 4pin)

Audio

Analog

2 x AESBalanced

(screw terminal)



Reference

USB




converter

• Synchronization & time base stabilization

• ARC with presets and size controls

• Adaptive recursive Noise Reduction with automatic noise level detection

• 20 point vertical-temporal aperture

• 12-bit decoding with 5-line comb filter

• 12-bit encoding

• Inputs PAL, NTSC, NTSC-J, NTSC4.4, PAL-N, PAL-M, SECAM with automatic input detection






• Unique genlock 'Floating mode*'

• Composite inputs tolerant to noise & errors

• Video gain, black level, chroma gain, NTSC hue

• RollCall compatible via USB link

• Compact ½ rack width with optional rack mount kit. Low power (no fan)


Inputs and Outputs

Video Input





Video Output

2 x SDI ................................525/625 line (BNC)



* No SCH lock

Video Input/Output


Audio Options

2 x AES input ......................Balanced (2-part screw terminal) 32-96kHz PCM audio

2 x AES output ...................Balanced (2 part screw terminal) 48kHz PCM audio




Control Features


Output Standard..................525; 625











ARC Enable ........................Off/On























Power ..................................Standby

Rollcall



System Parameters

Processing ......................... ≥10 bit






Analogue Audio ADC ..........24 bit; THD better than <0.004%

Mechanical




Full Product List Base Model Kudos Plus CVR600BDV (3598406) The CVR600BDV is a multi-standard broadcast quality synchronizer, noise reducer and time base stabilizer with SDI, DV, composite and YC interfaces, 12 bit sampling and 10 bit processing featuring embedded and balanced AES audio Base Model Kudos Plus CVR600BDV (3598406-RM) As above, with rack mount kit Option Rack mount kit (INSY-MNT-KIT) Rack mount kit to mount one or two units in a 19” rack



CVR600BD SDI & Composite Standards Converter Broadcast quality standards converter and synchronizer with AES and embedded audio The CVR600BD is a multi-standard broadcast quality 12-bit sampling, 10-bit processing standards converter, synchronizer, aspect ratio converter, noise reducer and time base stabilizer with SDI, composite and YC interfaces. Standards conversion between 525 and 625 line standards (NTSC/PAL) employs a powerful 20 point, 4-field, 5-line interpolation aperture to give smooth motion and maximum vertical resolution. Embedded audio is processed as well as providing balanced AES audio interfaces

Audio

Video Processing




2 x CompositeVideo

1 x Y/C(miniDIN4)

Analog

Digital


audio

2 x AESBalanced

(screw terminal)

Audio Processing


SDI Embeddedaudio

CompositeVideo

Y/C(miniDIN4)

Digital

SDIwith embedded

audio

Audio

Analog

2 x AESBalanced

(screw terminal)



Reference

USB




converter






• 12-bit encoding













Inputs and Outputs

Video Input





Video Output

2 x SDI ................................525/625 line (BNC)

2 x Composite *...................27MHz, 12-bit D to A. Output Formats PAL, NTSC, NTSC-J, PAL-N, PAL-M (BNC)

1 x YC * ...............................27MHz, 12-bit D to A. Output Formats PAL, NTSC, NTSC-J, PAL-N, PAL-M (Mini DIN4)

* No SCH lock

Audio Options






Control Features


Output Standard..................525; 625










ARC Enable ........................Off/On






















Power ..................................Standby

Rollcall



System Parameters

Processing ......................... ≥10 bit







Mechanical




Full Product List Base Model Kudos Plus CVR600BD (3598403) The CVR600BD is a multi-standard broadcast quality synchronizer, noise reducer and time base stabilizer with SDI, composite and YC interfaces, 12 bit sampling and 10 bit processing featuring embedded and balanced AES audio. Base Model Kudos Plus CVR600BD (3598403-RM) As above, with rack mount kit. Option Rack mount kit (INSY-MNT-KIT) Rack mount kit to mount one or two units in a 19” rack



CVR600ADV SDI, DV & Composite Standards Converter Broadcast quality standards converter and synchronizer The CVR600ADV is a multi-standard broadcast quality 12-bit sampling, 10-bit processing standards converter, synchronizer, aspect ratio converter, noise reducer and time base stabilizer with SDI, DV, composite and YC interfaces. Standards conversion between 525 and 625 line standards (NTSC/PAL) employs a powerful 20 point, 4-field, 5-line interpolation aperture to give smooth motion and maximum vertical resolution. Embedded audio is processed as well as providing analog audio interfaces

Audio

Video Processing




2 x CompositeVideo

1 x Y/C(miniDIN4)

Analog

Digital


audio

DVwith audio

(1394 4pin)

2 x Analog(screw terminal)

Audio Processing



CompositeVideo

Y/C(miniDIN4)

Digital

SDIwith embedded

audio

DVwith audio

(1394 4pin)

Audio

Analog




Reference

USB



Features • Standards Converter & Aspect ratio converter






• 12-bit encoding












Applications • Universal Analog / Digital interface

• Audio embedding & extraction

• Satellite down-link & radio links

• Ingest / PC capture pre-processing

• Duplication

• VHS dubbing

• Format conversion

Inputs and Outputs

Video Input





Video Output

2 x SDI ................................525/625 line (BNC)



* No SCH lock

Video Input/Output


Audio Options

4 x Analogue input ..............Balanced (2-part s crew terminal) +24 to +12dBu for 0dB FS

4 x Analogue output ...........Balanced (2-part s crew terminal) +24 to +12dBu from 0dB FS




Control Features


Output Standard..................525; 625











ARC Enable ........................Off/On























Power ..................................Standby

Rollcall



System Parameters

Processing ......................... ≥10 bit







Mechanical




Full Product List Base Model Kudos Plus CVR600ADV (3598405) The CVR600ADV is a multi-standard broadcast quality synchronizer, noise reducer and time base stabilizer with SDI, DV, composite and YC interfaces, 12 bit sampling and 10 bit processing featuring embedded and analog audio Base Model Kudos Plus CVR600ADV (3598405-RM) As above, with rack mount kit. Option Rack mount kit (INSY-MNT-KIT) Rack mount kit to mount one or two units in a 19” rack



CVR600AD SDI & Composite Standards Converter Broadcast quality standards converter and synchronizer with analog and embedded audio The CVR600AD is a multi-standard broadcast quality 12-bit sampling, 10-bit processing standards converter, synchronizer, aspect ratio converter, noise reducer and time base stabilizer with SDI, composite and YC interfaces. Standards conversion between 525 and 625 line standards (NTSC/PAL) employs a powerful 20 point, 4-field, 5-line interpolation aperture to give smooth motion and maximum vertical resolution. Embedded audio is processed as well as providing analog audio interfaces

Audio

Video Processing




2 x CompositeVideo

1 x Y/C(miniDIN4)

Analog

Digital


audio


Audio Processing


SDI Embeddedaudio

CompositeVideo

Y/C(miniDIN4)

Digital

SDIwith embedded

audio

Audio

Analog




Reference

USB




converter






• 12-bit encoding













Inputs and Outputs

Video Input





Video Output

2 x SDI ................................525/625 line (BNC)



* No SCH lock

Audio Options






Control Features


Output Standard..................525; 625










ARC Enable ........................Off/On






















Power ..................................Standby

Rollcall



System Parameters

Processing ......................... ≥10 bit







Mechanical




Full Product List Base Model Kudos Plus CVR600AD (3598402) The CVR600AD is a multi-standard broadcast quality synchronizer, noise reducer and time base stabilizer with SDI, composite and YC interfaces, 12 bit sampling and 10 bit processing featuring embedded and analog audio Base Model Kudos Plus CVR600AD (3598402-RM) As above, with rack mount kit Option Rack mount kit (INSY-MNT-KIT) Rack mount kit to mount one or two units in a 19” rack



TBS190ADV SDI, DV & Composite synchronizer Broadcast quality synchronizer and time base stabilizer with analog and embedded audio The TBS190ADV is a multi-standard broadcast quality synchronizer, noise reducer and time base stabilizer with SDI, DV, composite and YC interfaces. Embedded audio is processed as well as providing analog audio interfaces. Featuring 12-bit sampling, 10-bit processing and rugged inputs, the TBS190ADV is equally suited to digitizing broadcast grade sources as with unstable, noisy sources.

Audio

Video Processing

SynchronizerTime Base Stabilizer


2 x CompositeVideo

1 x Y/C(miniDIN4)

Analog

Digital


audio

DVwith audio

(1394 4pin)


Audio Processing



CompositeVideo

Y/C(miniDIN4)

Digital

SDIwith embedded

audio

DVwith audio

(1394 4pin)

Audio

Analog




Reference

USB



Features • SDI, DV, Composite & YC

Synchronization • Time base stabilization • Adaptive recursive Noise Reduction with

automatic noise level detection • 12-bit decoding with 5-line comb filter • 12-bit encoding • Inputs PAL, NTSC, NTSC-J, NTSC4.4,





• Pass through for all HANC/VANC data • Composite inputs tolerant to noise &

errors • Unique genlock 'Floating mode*' • RollCall compatible via USB link


Inputs and Outputs

Video Input

2 x SDI ................................525/625 line with automatic detection(BNC)

2 x Composite .....................27MHz, 12-bit sampling PAL, NTSC, NTSC-J, NTSC4.4, PAL-N, PAL-M, SECAM with automatic detection(BNC)



Video Output

2 x SDI ................................525/625 line(BNC)

2 x Composite* ...................27MHz, 12-bit D to A. Output Formats PAL, NTSC, NTSC-J, PAL-N, PAL-M(BNC)


* No SCH lock

Video Input/Output


Audio Inputs & Outputs






Control Features





















Genlock Mode .....................Lock to reference; Lock to input ; Float (stabilized) - if same line standard; Free-run





Indication / Monitoring (also Logging/ RollTrack)



Power ..................................Standby

Rollcall



System Parameters

Processing ......................... ≥10 bit


SDI Data..............................All HANC & VANC data passed




Mechanical


Temperature .......................0°C to 35 °C operating -20 °C to +70 °C storage


Full Product List Base Model Kudos Plus TBS190ADV (3548605) The TBS190ADV is a multi-standard broadcast quality synchronizer, noise reducer and time base stabilizer with SDI, DV, composite and YC interfaces, 12 bit sampling and 10 bit processing featuring embedded and analog audio Base Model Kudos Plus TBS190ADV (3548605-RM) As above, with rack mount kit Option Rack mount kit (INSY-MNT-KIT) Rack mount kit to mount one or two units in a 19” rack



TBS190AD SDI & Composite synchronizer Broadcast quality synchronizer and time base stabilizer with analog and embedded audio The TBS190AD is a multi-standard broadcast quality synchronizer, noise reducer and time base stabilizer with SDI, composite and YC interfaces. Embedded audio is processed as well as providing analog audio interfaces. Featuring 12-bit sampling, 10-bit processing and rugged inputs, the TBS190AD is equally suited to digitizing broadcast grade sources as with unstable, noisy sources.

Audio

Video Processing



2 x CompositeVideo

1 x Y/C(miniDIN4)

Analog

Digital


audio


Audio Processing


SDI Embeddedaudio

CompositeVideo

Y/C(miniDIN4)

Digital

SDIwith embedded

audio

Audio

Analog




Reference

USB



Features • SDI, Composite & YC Synchronization • Time base stabilization • Adaptive recursive Noise Reduction with









Inputs and Outputs Video Input





Video Output

2 x SDI ................................525/625 line(BNC)



* No SCH lock







Control Features Input Select .........................SDI A,B; Composite A, B; YC


























Power ..................................Standby

Rollcall


Indication/monitioring parameters are available for Logging and RollTrack

System Parameters

Processing ......................... ≥10 bit






Mechanical




Full Product List Base Model Kudos Plus TBS190AD (3548602) The TBS190AD is a multi-standard broadcast quality synchronizer, noise reducer and time base stabilizer with SDI, composite and YC interfaces, 12 bit sampling and 10 bit processing featuring embedded and analog audio Base Model Kudos Plus TBS190AD (3548602-RM) As above, with rack mount kit Option Rack mount kit (INSY-MNT-KIT) Rack mount kit to mount one or two units in a 19” rack



TBS190BDV SDI, DV & Composite synchronizer Broadcast quality synchronizer and time base stabilizer with AES and embedded audio The TBS190BDV is a multi-standard broadcast quality synchronizer, noise reducer and time base stabilizer with SDI, DV, composite and YC interfaces. Embedded audio is processed as well as providing balanced AES audio interfaces. Featuring 12-bit sampling, 10-bit processing and rugged inputs, the TBS190BDV is equally suited to digitizing broadcast grade sources as with unstable, noisy sources.

Audio

Video Processing



2 x CompositeVideo

1 x Y/C(miniDIN4)

Analog

Digital


audio

DVwith audio

(1394 4pin)

2 x AESBalanced

(screw terminal)

Audio Processing



CompositeVideo

Y/C(miniDIN4)

Digital

SDIwith embedded

audio

DVwith audio

(1394 4pin)

Audio

Analog

2 x AESBalanced

(screw terminal)



Reference

USB



Features • SDI, DV, Composite & YC

Synchronization • Time base stabilization • Adaptive recursive Noise Reduction with














Video Output

2 x SDI ................................525/625 line(BNC)



* No SCH lock

Video Input/Output








Control Features Input Select .........................SDI A,B; DV; Composite A, B; YC



























Power ..................................Standby

Rollcall



System Parameters

Processing ......................... ≥10 bit





Mechanical




Full Product List Base Model Kudos Plus TBS190BDV (3548606) The TBS190BDV is a multi-standard broadcast quality synchronizer, noise reducer and time base stabilizer with SDI, DV, composite and YC interfaces, 12 bit sampling and 10 bit processing featuring embedded and balanced AES audio Base Model Kudos Plus TBS190BDV (3548606-RM) As above, with rack mount kit Option Rack mount kit (INSY-MNT-KIT) Rack mount kit to mount one or two units in a 19” rack



TBS190BD SDI & Composite synchronizer Broadcast quality synchronizer and time base stabilizer with AES and embedded audio The TBS190BD is a multi-standard broadcast quality synchronizer, noise reducer and time base stabilizer with SDI, composite and YC interfaces. Embedded audio is processed as well as providing balanced AES audio interfaces. Featuring 12-bit sampling, 10-bit processing and rugged inputs, the TBS190BD is equally suited to digitizing broadcast grade sources as with unstable, noisy sources.

Audio

Video Processing



2 x CompositeVideo

1 x Y/C(miniDIN4)

Analog

Digital


audio

2 x AESBalanced

(screw terminal)

Audio Processing


SDI Embeddedaudio

CompositeVideo

Y/C(miniDIN4)

Digital

SDIwith embedded

audio

Audio

Analog

2 x AESBalanced

(screw terminal)



Reference

USB

















Video Output

2 x SDI ................................525/625 line(BNC)



* No SCH lock
































Power ..................................Standby

Rollcall



System Parameters

Processing ......................... ≥10 bit





Mechanical




Full Product List Base Model Kudos Plus TBS190BD (3548603) The TBS190BD is a multi-standard broadcast quality synchronizer, noise reducer and time base stabilizer with SDI, composite and YC interfaces, 12 bit sampling and 10 bit processing featuring embedded and balanced AES audio Base Model Kudos Plus TBS190BD (3548603-RM) As above, with rack mount kit Option Rack mount kit (INSY-MNT-KIT) Rack mount kit to mount one or two units in a 19” rack



TBS190UDV SDI, DV & Composite synchronizer Broadcast quality synchronizer and time base stabilizer with AES and embedded audio The TBS190UDV is a multi-standard broadcast quality synchronizer, noise reducer and time base stabilizer with SDI, DV, composite and YC interfaces. Embedded audio is processed as well as providing unbalanced AES audio interfaces. Featuring 12-bit sampling, 10-bit processing and rugged inputs, the TBS190UDV is equally suited to digitizing broadcast grade sources as with unstable, noisy sources.

Audio

Video Processing



2 x CompositeVideo

1 x Y/C(miniDIN4)

Analog

Digital


audio

DVwith audio

(1394 4pin)

2 x AESUnbalanced

Audio Processing



CompositeVideo

Y/C(miniDIN4)

Digital

SDIwith embedded

audio

DVwith audio

(1394 4pin)

Audio

Analog

2 x AESUnbalanced



Reference

USB



Features • SDI, DV, Composite & YC Synchronization • Time base stabilization • Adaptive recursive Noise Reduction with

automatic noise level detection • 12-bit decoding with 5-line comb filter • 12-bit encoding • Inputs PAL, NTSC, NTSC-J, NTSC4.4, PAL-N,

PAL-M, SECAM with automatic input detection

• Outputs PAL, NTSC, NTSC-J, PAL-N, PAL-M • 4 channel (2 pair) embedded audio processing • Seamless PCM audio tracking delay with

manual offset – up to 2.5s • Pass through for all HANC/VANC data • Composite inputs tolerant to noise & errors • Unique genlock 'Floating mode*' • RollCall compatible via USB link







Video Output

2 x SDI ................................525/625 line(BNC)



* No SCH lock

Video Input/Output








Control Features Input Select .........................SDI A,B; DV; Composite A, B; YC



























Power ..................................Standby

Rollcall



System Parameters

Processing ......................... ≥10 bit





Mechanical




Full Product List Base Model Kudos Plus TBS190UDV (3548607) The TBS190UDV is a multi-standard broadcast quality synchronizer, noise reducer and time base stabilizer with SDI, DV, composite and YC interfaces, 12 bit sampling and 10 bit processing featuring embedded and unbalanced AES audio Base Model Kudos Plus TBS190UDV (3548607-RM) As above, with rack mount kit Option Rack mount kit (INSY-MNT-KIT) Rack mount kit to mount one or two units in a 19” rack



TBS190UD SDI & Composite synchronizer Broadcast quality synchronizer and time base stabilizer with AES and embedded audio The TBS190UD is a multi-standard broadcast quality synchronizer, noise reducer and time base stabilizer with SDI, composite and YC interfaces. Embedded audio is processed as well as providing unbalanced AES audio interfaces. Featuring 12-bit sampling, 10-bit processing and rugged inputs, the TBS190UD is equally suited to digitizing broadcast grade sources as with unstable, noisy sources.

Audio

Video Processing



2 x CompositeVideo

1 x Y/C(miniDIN4)

Analog

Digital


audio

2 x AESUnbalanced

Audio Processing


SDI Embeddedaudio

CompositeVideo

Y/C(miniDIN4)

Digital

SDIwith embedded

audio

Audio

Analog

2 x AESUnbalanced



Reference

USB

















Video Output

2 x SDI ................................525/625 line(BNC)



* No SCH lock
































Power ..................................Standby

Rollcall



System Parameters

Processing ......................... ≥10 bit





Mechanical




Full Product List Base Model Kudos Plus TBS190UD (3548604) The TBS190UD is a multi-standard broadcast quality synchronizer, noise reducer and time base stabilizer with SDI, composite and YC interfaces, 12 bit sampling and 10 bit processing featuring embedded and unbalanced AES audio Base Model Kudos Plus TBS190UD (3548604-RM) As above, with rack mount kit Option Rack mount kit (INSY-MNT-KIT) Rack mount kit to mount one or two units in a 19” rack



Product Support Procedure If you experience any technical or operational difficulties with a Snell & Wilcox product please do not hesitate to contact us or utilize our online form to request assistance. There is a lot of information you can give us that will enable us to diagnose your problem swiftly. Please read the following guidelines, as these suggestions will help us to help you. Basic Information

For Units ......................Please provide the exact product Model, unit Serial Number and Software Version information.

For Cards or Modules ..Please provide the Sub-Assembly Number, card Serial Number and the

Software Version information. Basic Application

Inputs ...........................Please provide full details of the Input Signals being used including any references etc. and where they are being generated.

Outputs ........................Please provide full details of the Output Signals required and how they are

being monitored. System .........................Please provide a brief description of the system in which your S&W

equipment is currently being used. Basic Tests

Preset Unit ...................Please use the Preset Unit function to return the settings back to the factory default.

RollCall ........................Is your unit currently connected to a RollCall capable PC? This software is

obtainable for free and provides a very user friendly GUI for virtually all S&W equipment - perfect for complex products, large systems or those with passive front panels.

Card Edge Info. ...........What is the status of the card edge LEDs or display? These can often provide

information such as power status and input detection conditions. Internal TPG ................Many S&W products have an internal test pattern/tone generator. Please

activate this to assist you with your problem analysis. In addition to the above, please do not forget to provide us with all of the necessary contact information:

• Names • Telephone & Fax numbers • e-mail addresses • Business address

A form has been provided for this information and will be found on the next page or an on-line form is available on the Snell & Wilcox website at:

http://www.snellwilcox.com/support/request



Product Support Request Form

Name: *

Company:

Address Details: *

Post/ZIP Code:

Country: *

Telephone: *

Fax:

Email: *

Local S&W Center: *

Product Name: *

Switchers (i.e. Magic DaVE, Switchpack, Kahuna)

File & Data Transfer Products (i.e. RollCall, Memphis & iCR) Product Type: *

Video Products (i.e. Modular, Kudos Plus and Alchemist)

Unit Serial Number: * Fault/Spare Part Information: *

(please advise us how many units show this fault and the system layout showing all other manufacturers' products)

e-mail * Preferred Method of Contact:

Phone • Item is required.

Please mail to: Snell & Wilcox Ltd.,

Southleigh Park House, Eastleigh Road, Havant, Hants, PO9 2PE. United Kingdom.

Service Contact Information: Tel: +44 (0) 2392 489058

Fax: +44 (0) 2392 489057

http://www.snellwilcox.com/support

ftp://ftp.snellwilcox.com/support



Manual Revision Record

Date Version No. Issue No. Change Comments 7-Apr-06 1 1 First issue released

28-Sept-06 1 2 4 way connector drawing P11Contact numbers, support data and logo updated

New issue released

13-Feb-07 1 3 DV Interface data added New issue released 31-Mar-

08 1 3 Layout issues corrected. Content unchanged.

tbs190 op manual

Documents