table of contents treeliminator - land pride · ts55 skid steer tree saw treeliminator 328-049m...

Cover photo may show optionalequipment not supplied withstandard unit.

© Copyright 2008 Printed

Read the Operator’s manual entirely.When you see this symbol, thesubsequent instructions andwarnings are serious - follow withoutexception. Your life and the lives ofothers depend on it!

!

Table of Contents

7/14/08

328-049MOperator’s Manual

TS55 Skid Steer Tree Saw

TreeLiminator

20661

Land Pride

Table of Contents

Important Safety Information . . . . . . . . . . .1Signal Words . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Safety Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Introduction . . . . . . . . . . . . . . . . . . . . . . . .6Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Using This Manual . . . . . . . . . . . . . . . . . . . . . . . . . 6

Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Owner Assistance . . . . . . . . . . . . . . . . . . . . . . . . . 6Serial Number Plate . . . . . . . . . . . . . . . . . . . . . . . . 6Further Assistance . . . . . . . . . . . . . . . . . . . . . . . . . 6

Section 1: Assembly and Set-Up . . . . . . . .7Skid Steer Requirements . . . . . . . . . . . . . . . . . . . . 7Dealer Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . 7Skid Steer Hook-Up . . . . . . . . . . . . . . . . . . . . . . . . 7

Section 2: Operating Instructions . . . . . . .8Transporting the Skid Steer Loader and TreeLimina-tor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Operating Checklist . . . . . . . . . . . . . . . . . . . . . . . . 8Operating Instructions . . . . . . . . . . . . . . . . . . . . . . 8

Table of Contents

© Copyright 2008 All rights Reserved

Land Pride provides this publication “as is” without warranty of any kind, either expressedPride assumes no responsibility for errors or omissions. Neither is any liability assumed forthe right to revise and improve its products as it sees fit. This publication describes the stat

Land Pride is a reg

All other brands and product names are trademarks

Printed in the United

TS55 Skid Steer Tree Saw TreeLiminator 328-049M

Section 3: Maintenance & Lubrication . .10Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Saw Blade Sharpening . . . . . . . . . . . . . . . . . . . . . 10Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Lubrication Points . . . . . . . . . . . . . . . . . . . . . . . . 11

Power Jaw Pivot . . . . . . . . . . . . . . . . . . . . . . . 11Blade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Section 4: Specifications & Capacities . .12TS55 TreeLiminator . . . . . . . . . . . . . . . . . . . . . . . 12

Section 5: Features & Benefits . . . . . . . .13TS55 TreeLiminator . . . . . . . . . . . . . . . . . . . . . . . 13

Section 6: Troubleshooting . . . . . . . . . . .14Section 7: Appendix . . . . . . . . . . . . . . . . .15

Torque Values Chart . . . . . . . . . . . . . . . . . . . . . . 15Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

or implied. While every precaution has been taken in the preparation of this manual, Landdamages resulting from the use of the information contained herein. Land Pride reserves

e of this product at the time of its publication, and may not reflect the product in the future.

istered trademark.

or registered trademarks of their respective holders.

States of America.

7/14/08

Important Safety Information

Land Pride Table of Contents▲


7/

Keep RidersOff Machinery▲ Riders obstruct the operator’s

view. They can be struck byforeign objects or thrown from themachine.

▲ Never allow children to operateequipment.

F▲

These are common practices that may or may not be applicable to the products described inthis manual.

Signal WordsA Signal word designates a degreeor level of hazard seriousness. Thesignal words are:

Indicates an imminently hazardoussituation which, if not avoided, willresult in death or serious injury. Thissignal word is limited to the mostextreme situations, typically formachine components that, forfunctional purposes, cannot beguarded.

! DANGER!

14/08

or Your ProtectionThoroughly read and understandthe “Safety Label” section, read allinstructions noted on them.

!ThisIt me

ATTEBECOYOUR

Indicates a potentially hazardoussituation which, if not avoided, couldresult in death or serious injury, andincludes hazards that are exposedwhen guards are removed. It mayalso be used to alert against unsafepractices.

Indicates a potentially hazardoussituation which, if not avoided, mayresult in minor or moderate injury. Itmay also be used to alert againstunsafe practices.

! WARNING

! CAUTION

1TS55 Skid Steer Tree Saw TreeLiminator 328-049M

Shutdown and Storage▲ Lower machine to ground, turn off

engine, and remove the key.▲ Detach and store implements in a

area where children normally donot play. Secure implement byusing blocks and supports.

OFF

ON

is the safety alert symbol.ans:

NTION!ME ALERT!SAFETY IS INVOLVED!

2


TS55 Skid Steer Tree S

Land PrideTable of Contents

Transporting the Loaderand Attachment▲ Always drive up the ramp with

heavy end uphill. Engage parkingbrake.

▲ Secure loader and attachmentsusing tiedowns and chains. Usetowing vehicle and trailer ofadequate capacity.

Getting On and Off Safely

Before leaving theoperator’s seat:▲ Lower lift arms and put

attachment flat on the ground.▲ Stop the engine.▲ Engage the parking brake.▲ Raise seat bar and move controls

until both lock.▲ Remove the key to prevent

unauthorized starting.▲ Use the steps, grab-handles and

skid-resistant surfaces whengetting on or off the loader.

While Operating▲ Start loader with steering levers

and hydraulic controls in neutral.Keep bystanders away.


Practice Safe Maintenance▲ Understand procedure before

doing work. Use proper tools andequipment, refer to Operator’sManual for additional information.

▲ Work in a clean dry area.▲ Allow implement to cool

completely.▲ Do not grease or oil implement

while it is in operation.

aw TreeLiminator 328-049M

▲ Disconnect battery ground cable(-) before servicing or adjustingelectrical systems or beforewelding on implement.

▲ Inspect all parts. Make sure partsare in good condition & installedproperly.

▲ Remove buildup of grease, oil ordebris.

▲ Remove all tools and unusedparts from implement beforeoperation.

7/14/08


7/14/08

Land Pride Table of Contents

Prepare for Emergencies▲ Be prepared if a fire starts.▲ Keep a first aid kit and fire

extinguisher handy.▲ Keep emergency numbers for

doctor, ambulance, hospital andfire department near phone.

911

WearProtective Equipment▲ Protective clothing and equipment

should be worn.▲ Wear clothing and equipment

appropriate for the job. Avoidloose fitting clothing.

▲ Prolonged exposure to loud noisecan cause hearing impairment orhearing loss. Wear suitablehearing protection such asearmuffs or earplugs.

▲ Operating equipment safelyrequires the full attention of theoperator. Avoid wearing radioheadphones while operatingmachinery.

Avoid HighPressure Fluids Hazard▲ Escaping fluid under pressure can

penetrate the skin causing seriousinjury.

▲ Avoid the hazard by relievingpressure before disconnectinghydraulic lines.

▲ Use a piece of paper orcardboard, NOT BODY PARTS, tocheck for suspected leaks.

▲ Wear protective gloves and safetyglasses or goggles when workingwith hydraulic systems.

▲ If an accident occurs, see adoctor immediately. Any fluidinjected into the skin must besurgically removed within a fewhours or gangrene may result.


Safety at All TimesThoroughly read and understand theinstructions given in this manualbefore operation. Refer to the “SafetyLabel” section, read all instructionsnoted on them.▲ Operator should be familiar with

all functions of the unit.▲ Do not stand between the skid

steer loader and implement duringhitching.

▲ Keep hands, feet, and clothingaway from power-driven parts.

▲ Wear snug fitting clothing to avoidentanglement with moving parts.

▲ Never operate loader’s controlsfrom the ground.

▲ Always sit in the operator’s seatwhen activating the controls.

▲ Keep bystanders away fromloader and work area. Do notraise the lift arms and attachmentover another worker.

▲ Never carry riders or use loaderas a personlift.

▲ Travel up and down slopes, notacross them.

▲ Keep hands and feet on controlsor footrests. Never lean out thefront of the cab with the enginerunning.




Safety LabelsYour TreeLiminator comes equipped with all safety labels inplace. They were designed to help you safely operate your saw.

1. Read and follow label directions.2. Keep all safety labels clean and legible.3. Replace all damaged or missing labels. To order new labels

go to your Land Pride dealer.4. Some new equipment installed during repair requires safety

labels to be affixed to the replaced component as specifiedby Land Pride. When ordering new components make surethe correct safety labels are included in the request.

5. Refer to this section for proper label placement.To install new labels:a. Clean the area the label is to be placed.

b. Spray soapy water on the surface where the label is tobe placed.

c. Peel backing from label. Press firmly onto the surface.

d. Squeeze out air bubbles with the edge of a credit card.

4 TS55 Skid Steer Tree Saw TreeLiminator 328-049M 7/14/08

838-112CDanger: PinchingHazard

20661

20661838-106CWarning: General Safety

5


7/14/08 TS55 Skid Steer Tree Saw TreeLiminator 328-049M


838-094C

Warning: High Pressure Fluid20661

20661838-432C

Danger: Utilities

20661

838-433C

Danger: Saw Blade

(Both Sides)

Introduction


Introduction
Land Pride welcomes you to the growing family of newproduct owners.
This saw has been designed with care and built by skilledworkers using quality materials. Proper assembly,maintenance, and safe operating practices will help youget years of satisfactory use from this saw.

ApplicationThe TreeLiminator is a skid steer mounted 6’ pie shapedblade with saw teeth on each side. As you drive the skidsteer forward, the cutting teeth are forced into the trunkof the tree. The TreeLiminator is ideal for clearingpastures or unwanted trees in a fraction of the timeneeded with a chain saw, and less costly than a dozer.

While other tree saws on the market utilize hydrauliccylinders and other moving parts, our tree saw’s onlymoving part is a “Power Jaw” that acts as a one armedgrapple to help grab trunks and piles of limbs. Easily sawtrees along the fence row, and reach over the fence toremove them with the “Power Jaw”. See “Features andBenefits”, “Section 6” for additional information.

Using This Manual• This Operator’s Manual is designed to help familiarize

you with safety, assembly, operation, adjustments,troubleshooting, and maintenance. Read this manualand follow the recommendations to help ensure safeand efficient operation.

• The information contained within this manual wascurrent at the time of printing. Some parts may changeslightly to assure you of the best performance.

• To order a new Operator’s or Parts Manual contactyour authorized dealer. Manuals can also bedownloaded, free-of-charge from our website atwww.landpride.com or printed from the Land PrideService & Support Center by your dealer.

Terminology“Right” or “Left” as used in this manual is determined byfacing the direction the machine will operate while in useunless otherwise stated.

Definitions

Owner AssistanceThe Warranty Registration card should be filled out bythe dealer at the time of purchase. This information isnecessary to provide you with quality customer service.

NOTE: A special point of information that theoperator must be aware of before continuing.

IMPORTANT: A special point of information relatedto its preceding topic. Land Pride’s intention is thatthis information should be read and noted beforecontinuing.

6 TS55 Skid Steer Tree Saw TreeLiminator 328-049M

If customer service or repair parts are required contact aLand Pride dealer. A dealer has trained personnel, repairparts and equipment needed to service the tree saw.

The parts on your tree saw have been specially designedand should only be replaced with genuine Land Prideparts. Therefore, should your tree saw requirereplacement parts go to your Land Pride Dealer.

Serial Number PlateFor prompt service always use the serial number andmodel number when ordering parts from your Land Pridedealer. Be sure to include your serial and model numbersin correspondence also. Refer to Figure 1 for the locationof your serial number plate.

Serial Number Plate LocationFigure 1

Further AssistanceYour dealer wants you to be satisfied with your new saw.If for any reason you do not understand any part of thismanual or are not satisfied with the service received, thefollowing actions are suggested:

1. Discuss the matter with your dealership servicemanager making sure he is aware of any problemsyou may have and that he has had the opportunity toassist you.

2. If you are still not satisfied, seek out the owner orgeneral manager of the dealership, explain theproblem and request assistance.

3. For further assistance write to:

Land Pride Service Department1525 East North Street

P.O. Box 5060Salina, Ks. 67402-5060

E-mail [email protected]

20661

7/14/08

Section 1: Assembly and Set-Up


Section 1: Assembly and Set-Up2. The top of the skid steer hitch plate should be tilted
Skid Steer Requirements
This saw is designed to fit on Skid Steer Loaders with aSAE lift capacity of 1200 lbs., hydraulic requirements of11 GPM at 2200 psi minimum, a minimum GVW of 3500lbs. and properly counter-weighted. Refer to your SkidSteer Operator’s Manual for counter-weighting. The SkidSteer must have a minimum 70 HP capability. Tracks arehighly recommended for commercial application, and onunits that will continuously be operated on difficult anduneven terrain.

Dealer AssemblyRefer to Figure 1-1:4. Assemble Tree Guard (#1) to saw with 5/8” bolts (#2)

and flange nuts (#3).

Skid Steer Hook-Up

! CAUTIONDo not stand between the skid steer loader and implementduring hook-up.

1. Drive the skid steer slowly to the saw making surethe front hitch plate of the skid steer is parallel withthe Tree Saw hitch.

IMPORTANT: The TreeLiminator must be operatedwith a skid steer with a full safety enclosure.

7/14/08

Power Jaw

Saw Blades

Tree Guard

Power Jaw Cylinde

slightly forward.

3. Place the top of the skid steer hitch plate under thetop angled bar of the saw.

4. Slowly lift the skid steer hitch until the hitch of thesaw and the skid steer hitch have come together.

5. Push the lock handles of the skid steer down so thatthe pins go through the slots at the bottom of the TreeSaw hitch and lock in place.

6. Lower to ground, shut skid steer off, move levers torelieve hydraulic pressure.

7. Connect hydraulic hoses on the Tree Saw to the skidsteer loader.


Dealer AssemblyFigure 1-1

20663

r

Section 2: Operating Instructions



Transporting the Skid Steer Loaderand TreeLiminator1. Always drive up the loading ramp with the heavy end

uphill.

2. Once loaded, lower the saw to the floor, engage theparking brake, place shift lever into low gear or parkif available, shut engine off and remove switch key.

3. Secure loader and attachments using tie-downs andchains capable of withstanding forces exerted onthem while driving down the road. Use towing vehicleand trailer of adequate capacity.

Operating Checklist1. Be sure all bolts and nuts are tight.

2. Be certain all guards and shields are in place andsecure.

! WARNINGExtreme caution must be observed when removing trees thatare near or could come into contact with high voltage powerlines or fatality or serious injury may occur!

! WARNINGDo not operate the saw without the Tree Guard in place.

! CAUTIONA hard hat, safety glasses and work gloves should be worn atall times!

! CAUTIONAlways be aware of people, livestock, well heads, gas mains orother potential ground hazards in your immediate work area!

! CAUTIONDo not attempt to remove trees that exceed 30” in diameter!

! CAUTIONWhen transporting trees in the power jaw, keep load balancedand as low to the ground as possible!

! CAUTIONKeep bystanders at least 20 feet away when operating!

! CAUTIONAlways adhere to all Skid Steer manufacturer’s operating andsafety instructions!

Operating Instructions

! WARNINGCutting a tree with a cut that is horizontal to the ground ismore difficult to control than one cut by hand. Be aware ofwhich way the cut tree is going to fall. If a tree starts to falltowards you, the shortest path out of the way is to pivot 90degrees away from the tree and to the side.

! WARNINGThe falling tree’s path can change due to branches deflectingoff of surrounding trees and/or by rolling, once the branchescome in contact with the ground.

! WARNINGBe alert for falling branches.

Start skid steer loader with steering levers and hydrauliccontrols in neutral.

Move steering lever controls smoothly. Hydrostatic drivesystems are responsive and the loader will moveimmediately when controls are activated. Do not pullback suddenly on the steering lever controls to stop theloader.

The operator must be proficient in operating the skidsteer loader before he can achieve the expertise neededto get the full benefit and efficiency out of operating theTreeLiminator. Thoroughly familiarize yourself with theoperation of the skid steer loader.

Practice maneuvering the TreeLiminator attached to theskid steer loader in an open area. Raise it high in the airand tilt it up and down. Practice lowering theTreeLiminator from high in the air to the ground whilekeeping it level. Once you are comfortable operating theskid steer loader with the TreeLiminator attached, youare ready to saw a tree down.

Position the saw blade point on the side of the tree youwant to cut on. The fact that the saw gets wider as youdrive forward forcing the saw to enter the tree may beenough to initiate a sawing action. If this is not the case,force the saw teeth into the tree by slightly steeringtowards the tree.

The sawing action is done as you drive forward. Aftereach forward pass, reverse, reposition if needed, anddrive forward again. Keep repeating this procedure untilthe tree is completely cut through. Some trees may beeasier to cut by going at it from both sides.

IMPORTANT: DO NOT drop the saw. The sawshould be lower slowly to the ground and it must belevel from front to rear and side to side for properperformance.




! WARNINGWhen cutting a large tree, or one where safety is in question,it is recommended that a cut be made through the tree to thepoint of the tree feeling loose. At this point in the cut, raise theTreeLiminator high enough on the tree to push it in thedirection you want it to fall. The tree likely will fall over,splintering at the base. The remaining stump can then be cutoff at ground level.

After sawing the first couple of trees, stop and check tosee that the saw is adjusted properly.

Activate the hydraulic power jaw with the skid steerhydraulic control. The power jaw can be used to carry ordrag large trees or piles of limbs to a central pile.


Section 3: Maintenance & Lubrication


area (shown about 1/2” long). Grind material to achieve asharp front edge on the tooth.

MaintenanceSection 3: Maintenance & Lubrication

! CAUTIONBEFORE any maintenance is performed, lower the saw to theground, stop skid steer engine and remove key. DO NOTattempt to make maintenance adjustments while skid steer isrunning.

Proper servicing and adjustment is the key to the long lifeof any implement. With careful and systematicinspection, you can avoid costly maintenance, time andrepair.

Saw Blade SharpeningRefer to Figure 3-1:

! CAUTIONALWAYS wear eye protection and gloves when sharpening theblade.

The best sharpening method is achieved by using a 4” or4 1/2“ hand held grinder. The teeth on the saw blade areshaped to have a relief angle for exposing the front pointfor cutting. The flat 1/2” area on the tooth profile is all thatis necessary to grind. Place grinder wheel flat on this

10 TS55 Skid Steer Tree Saw TreeLiminator 328-049M

Sharpen Backside of Points

1/2”

Grind Flat Surfaces

Grind Flat Surfaces

Blade SharpeniFigure

Short close spaced teeth situated between the two largerteeth are for depth cutting. Sharpening these teeth byholding the grinder flat to the back of tooth and grindingto a point. Do not grind the front side of the tooth.

StorageIt is good practice to clean off all dirt and grease that mayhave accumulated on any moving parts at the end of aworking season and if the saw is not going to be used forseveral days. Also, apply a film of oil along the full lengthof both cutting edges to prevent rusting.

Check the saw blade and power jaw gripper for wear andreplace if necessary.

Inspect the saw for loose, damaged or worn parts andadjust or replace if needed.

Lubricate as noted in “Lubrication Points” on page 11.Apply a light coat of grease to any exposed hydrauliccylinder rod.

Repaint parts where paint is worn or scratched to preventrust.

Store saw in a clean, dry place.

7/14/08

20665

ng Reference 3-1

Section 3: Maintenance & Lubrication


Lubrication Points

7/14/08

20661

20661

50Multi-purposespray lube

Multi-purposegrease lube

Intervals in hoursat which lubricationis required

LubricationLegend

Multi-purposeoil lube

25Hours

Power Jaw Pivot

Type of Lubrication: Multi-Purpose Grease

AsRequired

Blade

Type of Lubrication: Multi-Purpose Lube


Section 4: Specifications & Capacities


Section 4: Specifications & Capacities


TS55 TreeLiminator

TS55

Skid Steer 70 HP minimum, 1,200 lb. lift capacity, 3,500 lb. GVW with proper counter weight remotehydraulics and protective cage.

Hook-Up Quick-Attach Skid Plate

Approximate Machine Weight 900 lbs.

Length 8’ 9”

Width 68 3/8”

Height 73”

Saw Blade Material 5/16” T1 Plate

Nose Tube 2” x 5” x 1/4” Wall

Power Jaw 2” x 4” x 1/4” Wall, 2 1/2” x 8” Hydraulic Cylinder with Hose and Fittings

Section 5: Features & Benefits


Section 5: Features & Benefits


TS55 TreeLiminator

Features Benefits

Power Jaw (Hydraulic) The only moving part, less maintenance, wear and tear.For gripping trees or brush to transport.

Tree Guard To help keep branches and limbs from reaching operator.

Aggressive Saw Teeth For quicker sawing of trees.

Skid Steer Hook-Up Attaches to most late model Skid Steer units with the Quick attach skid plate.

Saw Blade Material Super hard, long lasting material.

Low Profile swept design Enables cutting at or below ground level.

Extended reach Enables cutting under or over fences and overhanging limbs.

Extended saw point Enables digging out of small root systems and minor dirt excavation.

Section 6: Troubleshooting


Section 6: Troubleshooting


Problem Solution

Hydraulic Leak Tighten fittings and hoses

Replace damaged hydraulics

Cuts trees slowly Sharpen saw teeth

Replace saw blade

Saw begins to lodge in tree Tree is falling toward saw, Cut from opposite side of tree

Power Jaw won’t clamp tree Center or balance on load

Cut or pinched hydraulic line

Hydraulic fluid low in skid steer

Can’t lift tree saw Check capacities of skid steer

Hydraulic fluid low in skid steer

Section 7: Appendix


Section 7: Appendix

Torque Values Chart

in-tpi 1 N · m ft-lb 3 N · m ft-lb N · m ft-lb mm x pitch N · m ft-lb N · m ft-lb N · m ft-lb1/4" - 20 7.4 5.6 11 8 16 12 M 5 X 0.8 4 3 6 5 9 7

1/4" - 28 8.5 6 13 10 18 14 M 6 X 1 7 5 11 8 15 11

5/16" - 18 15 11 24 17 33 25 M 8 X 1.25 17 12 26 19 36 27

5/16" - 24 17 13 26 19 37 27 M 8 X 1 18 13 28 21 39 29

3/8" - 16 27 20 42 31 59 44 M10 X 1.5 33 24 52 39 72 53

3/8" - 24 31 22 47 35 67 49 M10 X 0.75 39 29 61 45 85 62

7/16" - 14 43 32 67 49 95 70 M12 X 1.75 58 42 91 67 125 93

7/16" - 20 49 36 75 55 105 78 M12 X 1.5 60 44 95 70 130 97

1/2" - 13 66 49 105 76 145 105 M12 X 1 90 66 105 77 145 105

1/2" - 20 75 55 115 85 165 120 M14 X 2 92 68 145 105 200 150

9/16" - 12 95 70 150 110 210 155 M14 X 1.5 99 73 155 115 l215 160

9/16" - 18 105 79 165 120 235 170 M16 X 2 145 105 225 165 315 230

5/8" - 11 130 97 205 150 285 210 M16 X 1.5 155 115 240 180 335 245

5/8" - 18 150 110 230 170 325 240 M18 X 2.5 195 145 310 230 405 300

3/4" - 10 235 170 360 265 510 375 M18 X 1.5 220 165 350 260 485 355

3/4" - 16 260 190 405 295 570 420 M20 X 2.5 280 205 440 325 610 450

7/8" - 9 225 165 585 430 820 605 M20 X 1.5 310 230 650 480 900 665

7/8" - 14 250 185 640 475 905 670 M24 X 3 480 355 760 560 1050 780

1" - 8 340 250 875 645 1230 910 M24 X 2 525 390 830 610 1150 845

1" - 12 370 275 955 705 1350 995 M30 X 3.5 960 705 1510 1120 2100 1550

1-1/8" - 7 480 355 1080 795 1750 1290 M30 X 2 1060 785 1680 1240 2320 1710

1 1/8" - 12 540 395 1210 890 1960 1440 M36 X 3.5 1730 1270 2650 1950 3660 2700

1 1/4" - 7 680 500 1520 1120 2460 1820 M36 X 2 1880 1380 2960 2190 4100 3220

1 1/4" - 12 750 555 1680 1240 2730 2010

1 3/8" - 6 890 655 1990 1470 3230 2380 1 in-tpi = nominal thread diameter in inches-threads per

1 3/8" - 12 1010 745 2270 1670 3680 2710 2 N· m = newton-meters

1 1/2" - 6 1180 870 2640 1950 4290 3160 3 ft-lb= foot pounds

1 1/2" - 12 1330 980 2970 2190 4820 3560 4 mm x pitch = nominal thread diameter in millimeters x

Torque tolerance + 0%, -15% of torquing values. Unless otherwise specified use torque values listed above.

Grade 2 Grade 5 Grade 8

Bolt Head Identification

Bolt Size(Inches) Class 5.8 Class 8.8 Class 10.9

Bolt Head Identification

Bolt Size(Metric)

5.8 8.8 10.9


16

Notes

TS55 Skid Steer Tree Saw TreeLiminator 328-049M 7/14/08

Land Pride

Section 7: Appendix

7/14/08


WarrantyLand Pride warrants to the original purchaser that this Land Pride product will

be free from defects in material and workmanship beginning on the date ofpurchase by the end user according to the following schedule when used asintended and under normal service and conditions for personal use.

Overall Unit: One year Parts and Labor

Hydraulic Cylinder: One year Parts and Labor

Hoses & Seals: Considered wear items

Blades and Teeth: Considered wear items

This Warranty is limited to the replacement of any defective part by LandPride and the installation by the dealer of any such replacement part, and doesnot cover common wear items such as blades, belts, tines, etc. Land Pridereserves the right to inspect any equipment or parts which are claimed to havebeen defective in material or workmanship.

This Warranty does not apply to any part or product which in Land Pride’sjudgment shall have been misused or damaged by accident or lack of normalmaintenance or care, or which has been repaired or altered in a way whichadversely affects its performance or reliability, or which has been used for apurpose for which the product is not designed. Misuse also specifically includesfailure to properly maintain oil levels, grease points, and driveline shafts.

Claims under this Warranty must be made to the dealer which originally soldthe product and all warranty adjustments must be made through such dealer.Land Pride reserves the right to make changes in materials or design of theproduct at any time without notice.

This Warranty shall not be interpreted to render Land Pride liable for damagesof any kind, direct, consequential, or contingent to property. Furthermore, LandPride shall not be liable for damages resulting from any cause beyond itsreasonable control. This Warranty does not extend to loss of crops, any expenseor loss for labor, supplies, rental machinery or for any other reason.

No other warranty of any kind whatsoever, express or implied, is madewith respect to this sale; and all implied warranties of merchantability andfitness for a particular purpose which exceed the obligations set forth inthis written warranty are hereby disclaimed and excluded from this sale.

This Warranty is not valid unless registered with Land Pride within 30 daysfrom the date of purchase by the end user.


Corporate Office: P.O. Box 5060Salina, Kansas 67402-5060 USA

www.landpride.com

table of contents treeliminator - land pride · ts55 skid steer tree saw treeliminator 328-049m...

Documents