swoosh - mutual screw

PRODUCT DESCRIPTION: A high solids, high gloss, VOC compliant, oil modified polyurethane formulated for use on gymnasiums, residential and commercial wood flooring. USES: For use on wood floors as a sealer, permanent finish and protectorant. ADVANTAGES: Tough wear properties. Excellent adhesion. Long lasting. Protects wood floors with superior gloss. VOC compliant urethane coating. SPECIFICATIONS: Total Solids: 52% pH: 9.2-9.3 Color: Clear Solubility in Water: Insoluble Odor: Solvent Flash Point: 105˚ F Viscosity: Heavier Than Water Weight per Gallon: 7.45 Lbs. PRODUCT/CONTAINER DISPOSAL: Dispose of used/unwanted product according to state and local regula- tions. Offer container for recycling. SIZES AVAILABLE: 5 Gallon Pail DIRECTIONS FOR PRODUCT USE: CAUTION: If the composition or origin of an existing finish is unknown, it is strongly recommended that a test patch be applied to determine compatibility and adequate adhesion characteristics. FLOOR PREPARATION: Sanding is advisable for new floors and old, badly worn floors. After sanding, sweep or vacuum the floor to remove wood dust and dirt and then tack rag the floor using a waterless cleaner. SEALED FLOORS IN GOOD CONDITION: Clean heavily soiled floors thoroughly with a waterless cleaner. Allow the floor to dry, then screen with a 100-120 grit screen disk. Sweep or vacuum the floor to remove wood dust and dirt. Tack rag the floor to remove any fine dirt or dust left from screening. APPLYING THE FINISH: Apply finish only after the floor is thoroughly clean and dry. Apply finish with a lamb’s wool applicator, brush or drag/t-bar. Pour finish into an applicatior pan if applying with lamb’s wool or brush, or a plastic watering can for application with a drag/t- bar. Apply finish in a thin uniform coat. Under warm, low humidity conditions, allow 6-8 hours between coats. Apply no more than 2 coats in 24 hours. Under warm, low humidity conditions, floor may be opened to light traffic afet 24-36 hours. BUFFING BETWEEN COATS: Screen between coats with a 120 grit or finer screen to ensure adhesion and to remove raised grains in wood and provide a smoother finished appearance. Sweep or vacuum the floor to remove large quantities of wood and urethane dust. Tack rag floor to remove fine dust. Allow floor to dry thoroughly, then apply the next coat. Coverage: 500-600 square feet per gallon Technical Data Sheet It is recommended that protective gloves and safety glasses be worn when using this and all cleaning products. Refer to MSDS for further safety information. MANUFACTURED BY: 39-30 Review Avenue Long Island City, New York 11101 1-888 WAX PLUS • (718) 392-8080 Fax: (718) 482-9366 Visit us on the web! www.cleaning-solutions.com Swoosh Urethane Floor Sealer Sellador Uretano • VOC Compliant • Long Lasting Base Coat • Protects Porous Floors • High Gloss 2 0 0 2 FIRE HAZARD HEALTH HAZARD SPECIFIC HAZARD REACTIVITY Formula #1144 Formula #1144 Recyclable packaging 2 FLOOR COATING AND FINISHING MATERIAL AS TO SLIP RESISTANCE ONLY 210S

Upload: others

Post on 28-Feb-2022

4 views

Category:

Documents

0 download

Report

Download

Embed Size (px):

TRANSCRIPT

PRODUCT DESCRIPTION:A high solids, high gloss, VOC compliant, oil modifiedpolyurethane formulated for use on gymnasiums,residential and commercial wood flooring.

USES:For use on wood floors as a sealer, permanent finish andprotectorant.

ADVANTAGES:Tough wear properties. Excellent adhesion. Long lasting.Protects wood floors with superior gloss. VOC complianturethane coating.

SPECIFICATIONS:Total Solids: 52%pH: 9.2-9.3 Color: ClearSolubility in Water: InsolubleOdor: SolventFlash Point: 105˚ FViscosity: Heavier Than WaterWeight per Gallon: 7.45 Lbs.

PRODUCT/CONTAINER DISPOSAL:Dispose of used/unwanted product according to state and local regula-tions. Offer container for recycling.

SIZES AVAILABLE:5 Gallon Pail

DIRECTIONS FOR PRODUCT USE:CAUTION: If the composition or origin of an existing finish is unknown,it is strongly recommended that a test patch be applied to determinecompatibility and adequate adhesion characteristics.FLOOR PREPARATION: Sanding is advisable for new floors and old,badly worn floors. After sanding, sweep or vacuum the floor to removewood dust and dirt and then tack rag the floor using a waterlesscleaner.SEALED FLOORS IN GOOD CONDITION: Clean heavily soiled floorsthoroughly with a waterless cleaner. Allow the floor to dry, then screenwith a 100-120 grit screen disk. Sweep or vacuum the floor to removewood dust and dirt. Tack rag the floor to remove any fine dirt or dustleft from screening.APPLYING THE FINISH: Apply finish only after the floor is thoroughlyclean and dry. Apply finish with a lamb’s wool applicator, brush ordrag/t-bar. Pour finish into an applicatior pan if applying with lamb’swool or brush, or a plastic watering can for application with a drag/t-bar. Apply finish in a thin uniform coat. Under warm, low humidityconditions, allow 6-8 hours between coats. Apply no more than 2 coatsin 24 hours. Under warm, low humidity conditions, floor may be openedto light traffic afet 24-36 hours.BUFFING BETWEEN COATS: Screen between coats with a 120 grit orfiner screen to ensure adhesion and to remove raised grains in woodand provide a smoother finished appearance. Sweep or vacuum thefloor to remove large quantities of wood and urethane dust. Tack ragfloor to remove fine dust. Allow floor to dry thoroughly, then apply thenext coat.

Coverage: 500-600 square feet per gallon

Technical Data Sheet

It is recommended that protective gloves and safetyglasses be worn when using this and all cleaning products.Refer to MSDS for further safety information.

MANUFACTURED BY:

39-30 Review Avenue

Long Island City, New York 11101

1-888 WAX PLUS • (718) 392-8080 Fax: (718) 482-9366

Visit us on the web! www.cleaning-solutions.com

SwooshUrethane Floor SealerSellador Uretano

• VOC Compliant • Long Lasting Base Coat

• Protects Porous Floors • High Gloss

FIRE HAZARD

HEALTH HAZARD

SPECIFIC HAZARD

REACTIVITY