sut-250-s - snark sailboats · sut-250-s (these instructions are used for sut-250-sclc also) torque...
TRANSCRIPT
![Page 1: SUT-250-S - Snark Sailboats · SUT-250-S (These instructions are used for SUT-250-SCLC also) Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and](https://reader034.vdocuments.site/reader034/viewer/2022042218/5ec31cfdde5a6e256c6a1993/html5/thumbnails/1.jpg)
1
SUT-250-S (These instructions are used for SUT-250-SCLC also)
Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16,
9/16, and 3/4” combination wrenches, ratchet, 9/16, 3/4, 13/16”, and 7/8”
sockets.
ASSEMBLY REQUIREMENTS
*Torque all T-bolt nuts to 35-40 foot pounds.
*Check all lights before towing.
*Tire pressure not to exceed recommendation on serial tag.
*Re-torque wheel nuts after first 25 miles to 80 ft. pounds and
periodically thereafter.
Failure to follow the assembly instructions could result in serious injury or death.
Incorrect assembly or modifications to your trailer will void any specific or implied
warranty.
For questions or assistance assembling your trailer call 800-282-5042.
![Page 2: SUT-250-S - Snark Sailboats · SUT-250-S (These instructions are used for SUT-250-SCLC also) Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and](https://reader034.vdocuments.site/reader034/viewer/2022042218/5ec31cfdde5a6e256c6a1993/html5/thumbnails/2.jpg)
2
UNPACK AND IDENTIFY THE FOLLOWING PARTS.
Tongue section and angle bracket for cross members.
Side Rails and cross members
Axle assembly, springs and U bolt hardware.
![Page 3: SUT-250-S - Snark Sailboats · SUT-250-S (These instructions are used for SUT-250-SCLC also) Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and](https://reader034.vdocuments.site/reader034/viewer/2022042218/5ec31cfdde5a6e256c6a1993/html5/thumbnails/3.jpg)
3
Fenders and tires
Rollers winch post and braces.
![Page 4: SUT-250-S - Snark Sailboats · SUT-250-S (These instructions are used for SUT-250-SCLC also) Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and](https://reader034.vdocuments.site/reader034/viewer/2022042218/5ec31cfdde5a6e256c6a1993/html5/thumbnails/4.jpg)
4
Lights, brackets, harness, and hardware
Skid and side marker bracket
![Page 5: SUT-250-S - Snark Sailboats · SUT-250-S (These instructions are used for SUT-250-SCLC also) Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and](https://reader034.vdocuments.site/reader034/viewer/2022042218/5ec31cfdde5a6e256c6a1993/html5/thumbnails/5.jpg)
5
Tongue assembly
T-bolts
Unwrap the two tongue sections and loosen the nuts on the splice plates.
Also make sure that the front tongue section has 4 T-bolts on each side
before the tongue sections go together.
Slide splice plates over the adjacent tongue section until the plates are
centered between the tongue sections.
![Page 6: SUT-250-S - Snark Sailboats · SUT-250-S (These instructions are used for SUT-250-SCLC also) Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and](https://reader034.vdocuments.site/reader034/viewer/2022042218/5ec31cfdde5a6e256c6a1993/html5/thumbnails/6.jpg)
6
Tighten nuts.
Frame Assembly
Front cross member Side rails Rear cross member
![Page 7: SUT-250-S - Snark Sailboats · SUT-250-S (These instructions are used for SUT-250-SCLC also) Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and](https://reader034.vdocuments.site/reader034/viewer/2022042218/5ec31cfdde5a6e256c6a1993/html5/thumbnails/7.jpg)
7
Locate the front cross member and slide it into the front of the side rail.
Add the rear cross member to the side rail. Then attach the other side rail to
the cross members.
![Page 8: SUT-250-S - Snark Sailboats · SUT-250-S (These instructions are used for SUT-250-SCLC also) Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and](https://reader034.vdocuments.site/reader034/viewer/2022042218/5ec31cfdde5a6e256c6a1993/html5/thumbnails/8.jpg)
8
Square the frame and tighten all the corner brackets.
Your frame should look like this.
![Page 9: SUT-250-S - Snark Sailboats · SUT-250-S (These instructions are used for SUT-250-SCLC also) Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and](https://reader034.vdocuments.site/reader034/viewer/2022042218/5ec31cfdde5a6e256c6a1993/html5/thumbnails/9.jpg)
9
Frame Attachment
Locate the two angle brackets to install the frame to the tongue.
Slide two T-bolts forward from the left side of the rear tongue section to be
used to mount the angle brackets to the frame.
![Page 10: SUT-250-S - Snark Sailboats · SUT-250-S (These instructions are used for SUT-250-SCLC also) Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and](https://reader034.vdocuments.site/reader034/viewer/2022042218/5ec31cfdde5a6e256c6a1993/html5/thumbnails/10.jpg)
10
Rear cross member shown
Set the frame assembly on top of the tongue with the attaching brackets
behind the cross members.
Pencil marks
Take the angle brackets and install them on the tongue and front and rear
cross members. Line up the back edge of the brackets with the pencil marks
on the tongue.
![Page 11: SUT-250-S - Snark Sailboats · SUT-250-S (These instructions are used for SUT-250-SCLC also) Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and](https://reader034.vdocuments.site/reader034/viewer/2022042218/5ec31cfdde5a6e256c6a1993/html5/thumbnails/11.jpg)
11
Pencil marks
Line up the tongue with the pencil marks on the cross members. Tighten
nuts.
Your trailer should look like this at this point.
![Page 12: SUT-250-S - Snark Sailboats · SUT-250-S (These instructions are used for SUT-250-SCLC also) Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and](https://reader034.vdocuments.site/reader034/viewer/2022042218/5ec31cfdde5a6e256c6a1993/html5/thumbnails/12.jpg)
12
Spring Installation
Remove the bolt, nut and bushings from the front sub rail. Take the two
bushing and install them into the eye of the leaf spring as shown. Insert the
spring and bushing back into the sub rail.
![Page 13: SUT-250-S - Snark Sailboats · SUT-250-S (These instructions are used for SUT-250-SCLC also) Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and](https://reader034.vdocuments.site/reader034/viewer/2022042218/5ec31cfdde5a6e256c6a1993/html5/thumbnails/13.jpg)
13
Frame is shown up side down
Reinstall the nut and bolt into the center hole of the sub rail with the nut
towards the inside of the trailer. Do not tighten yet.
![Page 14: SUT-250-S - Snark Sailboats · SUT-250-S (These instructions are used for SUT-250-SCLC also) Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and](https://reader034.vdocuments.site/reader034/viewer/2022042218/5ec31cfdde5a6e256c6a1993/html5/thumbnails/14.jpg)
14
Remove the two bolts from the shackle holder at the rear of the spring and
install the shackle holder into the rear spring hanger with the nuts toward the
inside of the trailer. These nuts can be tightened at this time.
![Page 15: SUT-250-S - Snark Sailboats · SUT-250-S (These instructions are used for SUT-250-SCLC also) Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and](https://reader034.vdocuments.site/reader034/viewer/2022042218/5ec31cfdde5a6e256c6a1993/html5/thumbnails/15.jpg)
15
Serial plate
Locate the axle and install it on the springs as shown. Make sure the locating
studs on the springs are in the holes on the axle’s spring seat. Face the axle’s
serial plate toward the rear of the trailer to protect it from debris.
Locate the U-bolts and tie plates.
![Page 16: SUT-250-S - Snark Sailboats · SUT-250-S (These instructions are used for SUT-250-SCLC also) Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and](https://reader034.vdocuments.site/reader034/viewer/2022042218/5ec31cfdde5a6e256c6a1993/html5/thumbnails/16.jpg)
16
Install the U-bolts and tie plates as shown.
Install the nuts and tighten them evenly.
![Page 17: SUT-250-S - Snark Sailboats · SUT-250-S (These instructions are used for SUT-250-SCLC also) Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and](https://reader034.vdocuments.site/reader034/viewer/2022042218/5ec31cfdde5a6e256c6a1993/html5/thumbnails/17.jpg)
17
Go back and tighten all of the spring mounting nuts that were left loose
previously.
On the rear shackle, do not over tighten as this will not allow the suspension
to move properly.
![Page 18: SUT-250-S - Snark Sailboats · SUT-250-S (These instructions are used for SUT-250-SCLC also) Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and](https://reader034.vdocuments.site/reader034/viewer/2022042218/5ec31cfdde5a6e256c6a1993/html5/thumbnails/18.jpg)
18
Wiring
Locate harness and ring terminal.
Cut the white ground wire to 24” long. Strip the casing from the wire and
install the ring terminal.
![Page 19: SUT-250-S - Snark Sailboats · SUT-250-S (These instructions are used for SUT-250-SCLC also) Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and](https://reader034.vdocuments.site/reader034/viewer/2022042218/5ec31cfdde5a6e256c6a1993/html5/thumbnails/19.jpg)
19
Locate the ¾” long Philips screw.
Install Philips screw through the ground wire into the pre-drilled hole
located under the tongue just behind the coupler.
![Page 20: SUT-250-S - Snark Sailboats · SUT-250-S (These instructions are used for SUT-250-SCLC also) Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and](https://reader034.vdocuments.site/reader034/viewer/2022042218/5ec31cfdde5a6e256c6a1993/html5/thumbnails/20.jpg)
20
Extend a tape measure inside the tongue from the rear of the trailer until it
protrudes at the front of the trailer under the coupler.
Attach both wires of the harness to the end of the tape measure with either
tape or a tie. Retract the tape measure until it comes out the back of the
tongue with both wires attached.
![Page 21: SUT-250-S - Snark Sailboats · SUT-250-S (These instructions are used for SUT-250-SCLC also) Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and](https://reader034.vdocuments.site/reader034/viewer/2022042218/5ec31cfdde5a6e256c6a1993/html5/thumbnails/21.jpg)
21
Tail light brackets, tail lights
Locate the tail light brackets.
Locate the tail lights, carriage bolts, nuts and license plate bracket.
![Page 22: SUT-250-S - Snark Sailboats · SUT-250-S (These instructions are used for SUT-250-SCLC also) Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and](https://reader034.vdocuments.site/reader034/viewer/2022042218/5ec31cfdde5a6e256c6a1993/html5/thumbnails/22.jpg)
22
Slide one T-bolt from each side of the rear tongue section towards the front
of the trailer. Install tail light brackets and position them 8” from the rear of
the tongue.
Once tail light brackets are in position tighten nuts.
![Page 23: SUT-250-S - Snark Sailboats · SUT-250-S (These instructions are used for SUT-250-SCLC also) Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and](https://reader034.vdocuments.site/reader034/viewer/2022042218/5ec31cfdde5a6e256c6a1993/html5/thumbnails/23.jpg)
23
The light with the yellow wires is for the left (driver’s side) of the trailer.
Slide the carriage bolts into the slots in the back of the tail lights.
![Page 24: SUT-250-S - Snark Sailboats · SUT-250-S (These instructions are used for SUT-250-SCLC also) Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and](https://reader034.vdocuments.site/reader034/viewer/2022042218/5ec31cfdde5a6e256c6a1993/html5/thumbnails/24.jpg)
24
Repeat the process for the right side as shown.
Install the left tail light with the license plate holder between the light and
the bracket. Repeat for the other side. Tighten nuts but don’t over tighten
them.
![Page 25: SUT-250-S - Snark Sailboats · SUT-250-S (These instructions are used for SUT-250-SCLC also) Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and](https://reader034.vdocuments.site/reader034/viewer/2022042218/5ec31cfdde5a6e256c6a1993/html5/thumbnails/25.jpg)
25
Shown up side down
Locate the black tab on the underside of the tail light. Move the tab toward
the rear of the trailer and pull up releasing the bulb assembly from the light
housing.
![Page 26: SUT-250-S - Snark Sailboats · SUT-250-S (These instructions are used for SUT-250-SCLC also) Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and](https://reader034.vdocuments.site/reader034/viewer/2022042218/5ec31cfdde5a6e256c6a1993/html5/thumbnails/26.jpg)
26
Loosen the wire retaining screws and install the color matching wires from
the wire harness onto the corresponding retaining screws.
Re-install the bulb assembly into the light housing making sure to route the
wires through the slot in the base of the bulb assembly.
![Page 27: SUT-250-S - Snark Sailboats · SUT-250-S (These instructions are used for SUT-250-SCLC also) Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and](https://reader034.vdocuments.site/reader034/viewer/2022042218/5ec31cfdde5a6e256c6a1993/html5/thumbnails/27.jpg)
27
Install adhesive backed clamps in the locations shown and route the wires
through them.
Running lights, bracket and skid.
Locate the two amber running lights, four small Philips screws, adhesive
backed clamps, two ring terminals, and two blue connectors.
![Page 28: SUT-250-S - Snark Sailboats · SUT-250-S (These instructions are used for SUT-250-SCLC also) Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and](https://reader034.vdocuments.site/reader034/viewer/2022042218/5ec31cfdde5a6e256c6a1993/html5/thumbnails/28.jpg)
28
Cut approximately 8 ½” off of the white wires on both running lights. Strip
1/4” of insulation from the wire.
![Page 29: SUT-250-S - Snark Sailboats · SUT-250-S (These instructions are used for SUT-250-SCLC also) Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and](https://reader034.vdocuments.site/reader034/viewer/2022042218/5ec31cfdde5a6e256c6a1993/html5/thumbnails/29.jpg)
29
Install the ring terminals by crimping the terminal onto the bare wire.
Locate the skid and light bracket.
![Page 30: SUT-250-S - Snark Sailboats · SUT-250-S (These instructions are used for SUT-250-SCLC also) Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and](https://reader034.vdocuments.site/reader034/viewer/2022042218/5ec31cfdde5a6e256c6a1993/html5/thumbnails/30.jpg)
30
Take one T-bolt off the skid and slide it in the bottom of the tongue. Set the
skid aside for now. Install the bracket for the lights and position as shown.
Align the ring terminals with the screw hole nearest the wire on the back of
the running light. Make sure the wire is routed through the gap on the back
of the light so it does not become pinched when the light is installed.
![Page 31: SUT-250-S - Snark Sailboats · SUT-250-S (These instructions are used for SUT-250-SCLC also) Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and](https://reader034.vdocuments.site/reader034/viewer/2022042218/5ec31cfdde5a6e256c6a1993/html5/thumbnails/31.jpg)
31
Install the running lights into the pre-drilled holes in the running light
bracket using a Philips screwdriver. Be sure the screw is through the ring
terminal on the back side of the lights. This will supply a ground to the
lights. DO NOT OVER TIGHTEN
Cut 6” off of the brown wire on the left (driver’s side) running light. Do not
strip the wire.
![Page 32: SUT-250-S - Snark Sailboats · SUT-250-S (These instructions are used for SUT-250-SCLC also) Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and](https://reader034.vdocuments.site/reader034/viewer/2022042218/5ec31cfdde5a6e256c6a1993/html5/thumbnails/32.jpg)
32
Harness passes through open hole. Cut wire goes into closed off hole.
Insert brown wire that has been cut into the hole in the connector closest to
the hinge. This hole does not pass all the way through. The wire should go in
about ½”. Pass the other wire through the remaining open slot in the
connector at a point close to the running lights.
Use pliers to push the metal spade down until it is flush with the plastic. This
is what makes the electrical connection between the two wires. Close the
plastic cover of the connector over the spade until it snaps into position.
![Page 33: SUT-250-S - Snark Sailboats · SUT-250-S (These instructions are used for SUT-250-SCLC also) Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and](https://reader034.vdocuments.site/reader034/viewer/2022042218/5ec31cfdde5a6e256c6a1993/html5/thumbnails/33.jpg)
33
Cut the exposed strands of wire off of the end of the brown wire on the right
(passenger side) running light.
Cut the brown/green harness so it can be separated to accommodate the
connector. Be care full not to cut through the wires. Also cut as close to the
front of the tongue section as possible.
![Page 34: SUT-250-S - Snark Sailboats · SUT-250-S (These instructions are used for SUT-250-SCLC also) Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and](https://reader034.vdocuments.site/reader034/viewer/2022042218/5ec31cfdde5a6e256c6a1993/html5/thumbnails/34.jpg)
34
Pass the brown wire from the harness through the open slot in the connector
at this location. The green wire will rest just outside the connector. Insert the
brown wire from the running lights into the closed side of the connector and
close the spade and cover as previously described. This will make the
connection from the main harness to both running lights.
![Page 35: SUT-250-S - Snark Sailboats · SUT-250-S (These instructions are used for SUT-250-SCLC also) Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and](https://reader034.vdocuments.site/reader034/viewer/2022042218/5ec31cfdde5a6e256c6a1993/html5/thumbnails/35.jpg)
35
Locate the adhesive backed clamps. Install them as shown and run brown
wire from the running lights through them.
Install the skid on the front tongue section now. Tighten the nuts for the skid
in the location as shown.
![Page 36: SUT-250-S - Snark Sailboats · SUT-250-S (These instructions are used for SUT-250-SCLC also) Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and](https://reader034.vdocuments.site/reader034/viewer/2022042218/5ec31cfdde5a6e256c6a1993/html5/thumbnails/36.jpg)
36
Tape the harness as shown.
![Page 37: SUT-250-S - Snark Sailboats · SUT-250-S (These instructions are used for SUT-250-SCLC also) Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and](https://reader034.vdocuments.site/reader034/viewer/2022042218/5ec31cfdde5a6e256c6a1993/html5/thumbnails/37.jpg)
37
Fender Installation
Locate fenders, washers, T-bolts, and nuts.
Locate (2) 1 1/8” T-bolts from the hardware bag and install them into the
side rails. Slide them into position over the tire and install two rubber
washers and two steel washers as shown.
![Page 38: SUT-250-S - Snark Sailboats · SUT-250-S (These instructions are used for SUT-250-SCLC also) Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and](https://reader034.vdocuments.site/reader034/viewer/2022042218/5ec31cfdde5a6e256c6a1993/html5/thumbnails/38.jpg)
38
Install the fender, two more steel washers, and nuts, center the fender over
the axle and tighten the nuts. Repeat for the other side.
Locate 8 lug nuts, and wheels.
![Page 39: SUT-250-S - Snark Sailboats · SUT-250-S (These instructions are used for SUT-250-SCLC also) Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and](https://reader034.vdocuments.site/reader034/viewer/2022042218/5ec31cfdde5a6e256c6a1993/html5/thumbnails/39.jpg)
39
Install the wheels with the valve stems facing out. Install the lug nuts with
the tapered side facing the wheel.
Web strap clip installation
Locate 2 web strap clips
![Page 40: SUT-250-S - Snark Sailboats · SUT-250-S (These instructions are used for SUT-250-SCLC also) Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and](https://reader034.vdocuments.site/reader034/viewer/2022042218/5ec31cfdde5a6e256c6a1993/html5/thumbnails/40.jpg)
40
Install a web strap clip on each side rail at the back as shown. Then tighten
nuts.
![Page 41: SUT-250-S - Snark Sailboats · SUT-250-S (These instructions are used for SUT-250-SCLC also) Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and](https://reader034.vdocuments.site/reader034/viewer/2022042218/5ec31cfdde5a6e256c6a1993/html5/thumbnails/41.jpg)
41
Padded cradle installation
Locate padded cradles, brackets, and hardware.
Repair T-bolt
Locate the 4 angle brackets and repair T-bolts. Install the repair T-bolt on
the short end of the angle as shown.
![Page 42: SUT-250-S - Snark Sailboats · SUT-250-S (These instructions are used for SUT-250-SCLC also) Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and](https://reader034.vdocuments.site/reader034/viewer/2022042218/5ec31cfdde5a6e256c6a1993/html5/thumbnails/42.jpg)
42
Install two of the angle brackets on the front cross member and two on the
rear as shown. Also angle brackets can be installed on the top of the cross
member as shown below.
Slide T-bolt over on cross member and align them with the angle brackets.
![Page 43: SUT-250-S - Snark Sailboats · SUT-250-S (These instructions are used for SUT-250-SCLC also) Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and](https://reader034.vdocuments.site/reader034/viewer/2022042218/5ec31cfdde5a6e256c6a1993/html5/thumbnails/43.jpg)
43
Cradle bracket shown with 1” bolt and nut.
Shown on the bottom
![Page 44: SUT-250-S - Snark Sailboats · SUT-250-S (These instructions are used for SUT-250-SCLC also) Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and](https://reader034.vdocuments.site/reader034/viewer/2022042218/5ec31cfdde5a6e256c6a1993/html5/thumbnails/44.jpg)
44
Shown on the top
The angle bracket can be mounted either on the bottom or the top of the
cross member depending on the hull of the boat.
T-bolt 1” bolt
Install cradle bracket onto T-bolts on the front and rear cross members. Then
install a 1” bolt through the angle bracket at the bottom. Position brackets
and then tighten nuts.
![Page 45: SUT-250-S - Snark Sailboats · SUT-250-S (These instructions are used for SUT-250-SCLC also) Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and](https://reader034.vdocuments.site/reader034/viewer/2022042218/5ec31cfdde5a6e256c6a1993/html5/thumbnails/45.jpg)
45
Your trailer should look like this at this point.
Take the nuts and lock washers off the bottom of the padded cradles so they
can be installed on the angle brackets.
![Page 46: SUT-250-S - Snark Sailboats · SUT-250-S (These instructions are used for SUT-250-SCLC also) Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and](https://reader034.vdocuments.site/reader034/viewer/2022042218/5ec31cfdde5a6e256c6a1993/html5/thumbnails/46.jpg)
46
Install the padded cradles on the brackets as shown. Next reinstall the lock
washers and nuts then tighten.
The padded cradle holders will have to be adjusted for the boat after the
trailer is finished.
![Page 47: SUT-250-S - Snark Sailboats · SUT-250-S (These instructions are used for SUT-250-SCLC also) Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and](https://reader034.vdocuments.site/reader034/viewer/2022042218/5ec31cfdde5a6e256c6a1993/html5/thumbnails/47.jpg)
47
Locate the two roller assemblies.
![Page 48: SUT-250-S - Snark Sailboats · SUT-250-S (These instructions are used for SUT-250-SCLC also) Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and](https://reader034.vdocuments.site/reader034/viewer/2022042218/5ec31cfdde5a6e256c6a1993/html5/thumbnails/48.jpg)
48
Align the roller bracket with the two rear T-bolts on the front tongue section.
With the roller bracket tilted, gradually pull it over to the other side and
position it. Install nuts and tighten.
Remove the four T-bolts from the rear tongue section and install them into
the roller brackets as shown.
![Page 49: SUT-250-S - Snark Sailboats · SUT-250-S (These instructions are used for SUT-250-SCLC also) Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and](https://reader034.vdocuments.site/reader034/viewer/2022042218/5ec31cfdde5a6e256c6a1993/html5/thumbnails/49.jpg)
49
Now install the roller assembly on the rear tongue section as shown. Then
position and tighten nuts.
Bow Stand Assembly
Locate the bow stand.
![Page 50: SUT-250-S - Snark Sailboats · SUT-250-S (These instructions are used for SUT-250-SCLC also) Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and](https://reader034.vdocuments.site/reader034/viewer/2022042218/5ec31cfdde5a6e256c6a1993/html5/thumbnails/50.jpg)
50
Install the bow stand as shown. Final adjustments will be made when boat is
on the trailer. Be sure to go back and tighten all the nuts.
![Page 51: SUT-250-S - Snark Sailboats · SUT-250-S (These instructions are used for SUT-250-SCLC also) Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and](https://reader034.vdocuments.site/reader034/viewer/2022042218/5ec31cfdde5a6e256c6a1993/html5/thumbnails/51.jpg)
51
Finished trailer
![Page 52: SUT-250-S - Snark Sailboats · SUT-250-S (These instructions are used for SUT-250-SCLC also) Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and](https://reader034.vdocuments.site/reader034/viewer/2022042218/5ec31cfdde5a6e256c6a1993/html5/thumbnails/52.jpg)
52
KJM 1/5/11, REVISED 10/31/13, REVISED 9/10/14