sustainable buildings€¦ · us navy, norfolk naval shipyard american red cross susan b. anthony...
TRANSCRIPT
Nansulate® Energy Saving Coatings
Page 1
SUSTAINABLE BUILDINGSNew solutions to increase energy efficiency in buildings Industrial Nanotech, Inc., through the science of nanotechnology, has now provided an affordable retrofit solution to increase energy efficiency in existing buildings as well as new construction. Patented Nansulate® Translucent Insulation Coatings increase thermal resistance in a clear coating which is applied like a paint. These award-winning, low VOC coatings not only insulate and reduce energy use, they are also moisture and mold resistant for a healthier building.
Nansulate® Translucent Coatings: Insulated the skylights of the new Frost Art Museum in Miami, FL
Nansulate® Translucent Coatings: Insulated the exterior of the Soosung Apartments in Korea.
AN AFFORDABLE SOLUTION FOR LEED PROJECTS AND ENERGY EFFICIENT BUILDING MANDATES
Sustainability made simple Sustainability made affordable Nansulate® Coatings
Nansulate® Energy Saving Coatings
Page 2
Nansulate® coatings are a patented technology by Industrial Nanotech, Inc. that utilize a nanomaterial with an extremely low thermal conductivity. This material allows the coatings to effectively inhibit heat transfer in a thin layer.
Nansulate® offers an advancement to the traditional concept of thermal insulation, providing alternative solutions for sustainability and environmentally friendly energy efficiency.
A benefit of the translucent coatings is the increase to the thermal envelope of a building without reducing square footage or changing the look of the surface. Additional benefits are mold and moisture resistance, thus improving overall air quality.
Because Nansulate® does not rely on thickness as a function of its insulating ability, compression does not reduce its effectiveness. Nansulate® provides a health benefit by not harboring moisture, dust, mold, or dirt, which are factors that reduce traditional insulation’s effectiveness over time and decrease air quality.
New Technology - New Solutions for SustainabilityPRODUCT BENEFITS:
- Increases thermal resistance
- Excellent adhesion to a variety of surfaces, such as wood, brick, drywall, stucco, glass, concrete
- Resistant to mold and moisture
- Clear, matte finish does not change the look of the underlying surface
- Cost effective, easily applied with conventional equipment
- Can assist in earning LEED® points for Energy & Atmosphere, Indoor Environmental Quality, and Sustainable Sites categories
- Non-toxic, water-based
- Low VOC (100 grams/Liter)
- Breathable
- Encapsulation of lead based paint
Chart shows one customer’s reduction of energy use in KWH after using Nansulate® on the building envelope. Customer’s average reduction was 46%Nansulate® Energy Protect
To insulate building walls, skylights/windows & ceilings
Nansulate® LDXFor abatement of lead in
buildings
Nansulate® CrystalTo insulate and resist mold growth on sloped roofs.
Nansulate® Energy Saving Coatings
CONTACT: +52 (55) 2881 6834 - www.oenergy.com.mx - [email protected]
INSULATION - BUILDING ENVELOPENansulate® Energy Protect provides a flexible insulation solution for commercial and public buildings. It can be applied on walls, ceilings, duct work and other areas of the building envelope, while allowing the visual appeal of the building to remain intact. Nansulate® Crystal provides a clear insulation solution for sloped roofs of all types. Unlike traditional forms of insulation, Nansulate® coatings will not get infiltrated by moisture, mold, dust, or pests - and therefore maintains its insulating ability over time.
Building envelope insulation customers include: ✓ Bangkok Thailand International Airport✓ Louisiana Consolidated Government Animal Shelter✓ IMSS (Mexico’s Social Security and Health Administration)✓ National Decorating Service✓ U.S. Navy - Portsmouth Naval Shipyard
INSULATION - DAYLIGHTINGNansulate® Energy Protect over windows and skylights allows in diffused light, while insulating windows against heat transfer. Well designed daylighting allows in natural light that balances overhead electric lighting needs while curtailing glare. Nansulate® allows 92% visible light transmittance as tested on pane glass, and provides the opportunity to daylight without sacrificing building thermal performance. After coating, windows will have a ‘frosted’ look.
Skylight and window insulation customers include: ✓ City of Miami, Florida✓ Cornwell Quality Tools✓ Tampa Port Authority✓ Frost Art Museum at Florida International University
SUSTAINABILITY - ENVIRONMENTAL REMEDIATIONNansulate® coatings are naturally resistant to mold growth (without use of moldicides) and therefore will benefit air quality in a building by reducing potential for mold and mildew. There is also a version of Nansulate® - LDX, which can be used for encapsulation of dangerous lead-based paint and lead contamination. Nansulate® LDX is a clear, smooth lead encapsulation coating which can be used over a variety of surfaces.
Environmental remediation customers include: ✓ US Navy, Pearl Harbor Naval Base✓ US Navy, Norfolk Naval Shipyard✓ American Red Cross✓ Susan B. Anthony Voter’s Block Project✓ Government of Brunei - Royal Residential Palace✓ University of Wisconsin-Madison
Provide a custom solution with the newestenergy saving technology available
Patented technology that powers affordable sustainability.
Nansulate® Energy Saving Coatings
CONTACT: +52 (55) 2881 6834 - www.oenergy.com.mx - [email protected]
According to the U.S. Energy Information Administration, HVAC accounts for approximately 51% of the estimated energy consumption of U.S. Commercial Buildings.
And according to the Australian Government Department of Climate Change and Energy Efficiency, heating & cooling account for 54% of Australian commercial building energy share.
No matter where in the world you are, insulating is paramount to reducing building energy consumption and related greenhouse gas emissions.
For years we been trained to think that you need thickness in order to insulate. However just as cell phones and computers have shrunk and yet become more powerful over the years, so has insulation.
Nansulate® is the newest form of insulation. It incorporates a
nanomaterial with very low thermal conductivity into a clear water-based acrylic latex to provide a thin film coating which can be painted onto a variety of substrates to insulate
effectively and consistently. Building envelope customers will typically report energy savings of 20%-40% on heating and cooling costs, depending upon application.
Nansulate® offers an effective solution for reduction of energy consumption in buildings of all ages and construction types.
Affordable Option for Energy Efficiency
ROI EXAMPLE:According to the National Action Plan for Energy Efficiency, using 2003 EIA data, in the U.S., the average annual energy intensity for office buildings is 79.8 kBtu per square foot and the average cost is $1.65 per square foot.
$165,000 annual energy consumption for 100,000 SF building$72,600 used for heating/cooling (using 44% of total)$14,520/year energy savings with Nansulate® (using low 20% estimate)$48,500 Approximate cost of product to insulate walls/ceiling of 1-story building3.3 years payback (expected lifespan: 10+ years interior use, 5-10 years exterior)
Nansulate® Energy Saving Coatings
CONTACT: +52 (55) 2881 6834 - www.oenergy.com.mx - [email protected]
THERMAL TESTING DATA
Results from Standard Test Method for Steady-State Thermal Performance of Building Assemblies - UNI EN ISO 8990:1999:Thermal transmission through the wall section coated with Nansulate® was reduced by 34.80%Thermal resistance (1/U), measured in m2*k*w1, of the 8cm cement wall section coated with Nansulate® was increased by 28.98%
Description: Two wall samples are tested according to test standards for a variety of thermal measurements including thermal transmission, thermal conductance and thermal resistance. Testing was done by the accredited laboratory Istituto di Richerche E Collaudi - a certifying body for the Italian Government.(See data on page 6.)
MOLD TESTING
EMSL Analytical, Inc., one of the nation's leading testing laboratories, compared mold growth on wooden surfaces coated with Nansulate® HomeProtect, Nansulate® Bee Protect, Nansulate® GP, Nansulate® LDX and Nansulate® Top Coat products to surfaces with no coating. All were exposed to spore-producing bacteria, including Pencillium funiculosum, Aspergillus niger, Aureobasidium pullulans, Chaetomium globosum, and Trichoderma virens. After four weeks, the Nansulate® coatings exhibited zero or minimal mold growths, whereas the uncoated surfaces showed extreme to 100 percent mold coverage. The testing was conducted by EMSL Analytical, Inc., an AIHA accredited laboratory.
Photo shows the uncoated wooden control. Uncoated control is covered with mold growth.
Photo shows a Nansulate® coated wooden sample. The sample coated with Nansulate®
Results from ASTM D 5590 & ASTM G21Zero to minimal mold growth
Some nanotechnology products have come under scrutiny due to potential health issues posed by the use of nano-sized materials – particles smaller than one billionth of a meter. However, that is where Industrial Nanotech’s particle design approach differs. Instead of nano-sized particles, Nansulate® is made with larger micro-sized materials which use nanoscale internal architecture and surface chemistry to allow Nansulate® to have properties that are unique. The coatings are non-toxic, water-based, and low VOC (100 g/L).
HEATH & SAFETY
Nansulate® Coatings have undergone toxicology testing and have been found safe for use in homes, schools, food processing and other sensitive environments.
Testing example by university PhD student.
Nansulate® Energy Saving Coatings
CONTACT: +52 (55) 2881 6834 - www.oenergy.com.mx - [email protected]
Nansulate® Energy Saving Coatings
CONTACT: +52 (55) 2881 6834 - www.oenergy.com.mx - [email protected]
When the new state of the art international airport in Bangkok, Thailand was being built, sustainability was a huge part of the building plan.
The new Terminal Complex, in Nong Ngu Hao, Samut Prakarn Province, has a total floor area of 500,000m2 (5,381,955 SF), making it the largest airport in the world. Contractor H.R. Robertson supplied 11,530m2 (124,108 SF) of Robertson Wall Panels in fluorocarbon painted aluminum and steel, which were used as roof and
soffit claddings for the terminal building's aerobridges, including the double-decker aerobridges.
Nansulate® Translucent PT insulation coating was chosen as an innovative addition to the airport to reduce energy consumption and reduce condensation. It was coated onto all the Robertson wall panels to increase building energy efficiency and sustainability.
Nansulate® PT also offered a low VOC coating and resistance to mold growth for improved air quality.
This project was chosen in 2009 by the Journal of Architectural Coatings as a Top Green Global Project.
Sustainable Building Case Study
Suvarnabhumi International Airport Bangkok, Thailand
Nansulate® Energy Saving Coatings
CONTACT: +52 (55) 2881 6834 - www.oenergy.com.mx - [email protected]
Industrial Nanotech’s Mexico Distributor, Omnigenus® Energy, was assisting a large manufacturing client with an issue they were having with heat transferring through a large sheet metal wall that divides the main mezzanine from an area that holds six industrial ovens.
The heat transfer was causing uncomfortable working conditions.
Nansulate® Translucent PT was applied at a 3-coat coverage to a 3x3 meter section of the wall to illustrate the insulation performance.
Even before the coating was fully cured measurements showed a reduction of wall surface temperature from 39.9C (103.8F) to 24.8C (76.6F).
A reduction of 15.1C /27.2F. With further reduction expected after the coating cures fully.
Thermal imaging photos were also taken and clearly illustrate the reduction of heat transfer provided by the Nansulate® insulation coating technology.
Further application is being completed on two side walls and the ceiling.
BEFORE APPLICATION
DURING COAT #1
DURING COAT #2
AFTER ALL 3-COATS
www.oenergy.com.mx
Thermal Testing Case Study
Nansulate® Energy Saving Coatings
CONTACT: +52 (55) 2881 6834 - www.oenergy.com.mx - [email protected]
Located in the Main Street District of downtown Libertyville, IL, this sustainable design provides 13,800 square feet mixed use modern office and retail space with an historic context.
Bleck and Bleck Architects were tasked with using LEED guidelines to increase the energy efficiency of a
historical 1800's building, while also keeping the unique brick look of the building intact.
Nansulate® Energy Protect was applied to masonry walls to improve thermal resistance, reduce energy consumption, and provide UV and moisture resistance.
Excerpt from Masonry Edge Magazine:
"A challenge in reusing old masonry buildings is dealing with the energy envelope. Owners and designers love the interior appearance of the old, raw common brick walls. The typical wall is three solid wythes of brick thick, with no cavity for insulation to be injected. Infiltration can be addressed with various coatings, but until recently nothing could be done about thermal transmission.
Nanotechnology is a field that has shown tremendous promise in the area of materials science. The nanoparticles can be suspended in a low VOC medium and applied much like a paint."
Nansulate® provided an affordable way to increase energy efficiency while keeping the visual appeal of the historic building intact.
Sustainable Building Case Study
Muller Trading Company
Nansulate® Energy Saving Coatings
CONTACT: +52 (55) 2881 6834 - www.oenergy.com.mx - [email protected]
NA
NS
UL
AT
E®
CO
AT
ING
S A
ND
LE
ED
LE
ED
FO
R E
XIS
TIN
G B
UIL
DIN
GS
WH
ET
HE
R O
R N
OT
YO
U A
RE
US
ING
LE
ED
GU
IDE
LIN
ES
, YO
U C
AN
RE
FE
RE
NC
E T
HE
SE
AR
EA
S F
OR
IMP
RO
VE
D S
US
TAIN
AB
ILIT
Y.
Sust
aina
ble
Site
s (S
S)
Cre
dit 2
: Bui
ldin
g Ex
terio
r and
Har
dsca
pe
Man
agem
ent P
lan
= 1
pt
Coa
t ext
erio
r of b
uild
ing
with
N
ansu
late
® E
nerg
y Pr
otec
t. Th
e co
atin
g is
low
VO
C -
100
g/L,
m
inim
izin
g im
pact
on
the
envi
ronm
ent.
It is
als
o hi
ghly
re
sist
ant t
o m
oist
ure
and
grow
th o
f m
old,
as
wel
l as
UV
rays
, mea
ning
th
e ex
terio
r of t
he b
uild
ing
is m
ore
prot
ecte
d, a
nd w
ill ha
ve a
long
er
serv
ice
life
befo
re a
ny re
pain
ting
wou
ld b
e ne
eded
.
3
Ener
gy &
Atm
osph
ere
(EA
) Cre
dit
1: O
ptim
ize
Ener
gy E
ffici
ency
Pe
rfor
man
ce =
1-1
8 pt
s
NA
NSU
LATE
® O
PTIO
NS:
Coa
t int
erio
r or e
xter
ior w
alls
& c
eilin
gs w
ith N
ansu
late
® E
nerg
y Pr
otec
t.
Coa
t wat
er h
eate
rs, b
oile
rs, d
uctw
ork,
pip
ing
with
Nan
sula
te®
Tr
ansl
ucen
t PT.
Coa
t slo
ped
roof
s w
ith N
ansu
late
® C
ryst
al.
The
coat
ings
offe
r an
easy
, affo
rdab
le w
ay to
upg
rade
a b
uild
ing’
s en
ergy
ef
ficie
ncy
by a
ddin
g in
sula
tion
in c
oatin
g fo
rm to
the
wal
ls, c
eilin
gs o
r roo
f of a
bu
ildin
g, o
r to
the
wat
er h
eatin
g sy
stem
and
pip
ing.
ISO
sta
ndar
d te
stin
g fo
r th
erm
al p
erfo
rman
ce o
f bui
ldin
g as
sem
blie
s sh
ows
that
the
coat
ings
blo
ck
34.8
% o
f the
rmal
tran
smis
sion
, as
test
ed o
n 8c
m c
emen
t wal
l sec
tions
at a
3-
coat
cov
erag
e. C
usto
mer
fiel
d st
udie
s sh
ow a
dec
reas
e of
hea
ting/
cool
ing
cost
s be
twee
n 20
%-4
0% in
a v
arie
ty o
f clim
ates
, fro
m A
lask
a to
Flo
rida.
2
Indo
or E
nviro
nmen
tal
Qua
lity
(IEQ
) Cre
dit 2
.4:
Day
light
and
Vie
ws
= 1
pt
Coa
t win
dow
s an
d sk
ylig
hts
with
Nan
sula
te®
Ene
rgy
Prot
ect.
The
coat
ing
allo
ws
thro
ugh
visi
ble
light
, whi
le
redu
cing
gla
re a
nd U
V an
d in
crea
sing
ther
mal
resi
stan
ce.
1
Nansulate® Energy Saving Coatings
CONTACT: +52 (55) 2881 6834 - www.oenergy.com.mx - [email protected]
Color: Clear, matte finish - smooth surface
Environmental: Low VOC (100 g/litre) - water based
Product Attributes: Encapsulation of lead, mold resistance
Material Applied to: Lead based paint and lead contaminated surfaces
Color: Clear, matte finish - smooth surface
Environmental: Low VOC (100 g/litre) - water based
Product Attributes: Thermal insulation, mold resistance, UV resistance
Material Applied to: Drywall, pre-painted walls, ceilings, wood, plastic, glass, cement, stucco, other building surfaces.
NANSULATE® Energy ProtectClear thermal insulation and mold resistant coatingFOR: Commercial building envelope
NANSULATE® LDXClear lead encapsulation coatingFOR: Safe abatement of lead
Color: Clear, matte finish - smooth surface
Environmental: Low VOC (100 g/litre) - water based
Product Attributes: Thermal insulation, mold resistance, UV resistance
Material Applied to: Sloped Roofs of all types
NANSULATE® CrystalClear lead encapsulation coatingFOR: Sloped roofs