SURVEYING INSTRUMENTS

Series130R

Laser beam image is simulated. Guide Light Unit is a factory option.

EXPAND YOUR REACH WITH REFLECTORLESS RANGE FROM 30cm TO 350M /1FT. TO 1,140FT.

Superior Range, Speed & Accuracy

Reflectorless Total Stations

Innovative Technology Ma

■ EDM technology takes a big leap forward with state-of-the-art RED-tech II EDM

● 350m or 200m—choose the range you needThe Class 3R laser models provide reflectorless measurementup to 350m (1,140 ft.), while the Class 2 laser models cover arange up to 200m (650ft.). All models offer measurement fromas close as 0.3m (1ft.) for reflectorless measurement over atremendous range of distances, while assuring survey-gradeaccuracy .

● High-speed measurement now over 30% faster*

Measurement is fast at every 0.9 secondand just 1.7 seconds for the initialmeasurement (in fine mode) for speedgains of over 30%.

* Compared with first-generation RED-tech EDM

models.

Pinpoint reflectorless measurement over an ultra-wide range RED-tech II EDM retains the best of first-generation RED-tech EDM technology —including close-range reflectorless measurement from just 0.3m(1ft.)—and takes it to a whole new level of performance.

■ The proven technology behind RED-tech II EDMRED-tech II EDM is a high-performance phase-comparison measuring system that deliversunprecedented distance measurement of a variety of objects under conditions difficult orimpossible with other EDMs.

● Phase-comparison measurementRED-tech II EDM uses phase comparison technology, which provides notable advantages in accuracycompared with EDMs using pulse measurement methods. Combined with Sokkia's leading edge digitalsignal processing technology and refined optics, superbly accurate reflectorless measurement is now areality.

● Digital signal processingRED-tech II EDM simultaneously samples measuring signals in three different frequencies andcalculates distances using advanced digital signal processing software. A calculation method bestsuited to the condition of the measuring signals is selected, and receiving signals are amplified toensure a high level of reliability. Thanks to leading-edge signal processing techniques, RED-tech II EDMdelivers superior accuracy and with greater speed and efficiency compared with conventional EDMs.

● High-precision opticsSokkia has further refined its traditional optics system, which emits measuring light from the objectivelens center and receives the returning light along its periphery. With enhanced optics that provide the ideal light path, RED-tech II EDM dramatically increases reliabilityby emitting the laser beam from in front of the objective lens to eliminate errors caused by internalreflection. And its highly tunable optical components ensure that only the necessary returning light isdirected to the receiver for faster, more efficient measurement. What’s more, the telescope provides anextremely bright and sharp sight, and its compact size makes sighting easier than ever.With its one light source, with its one optics system, RED-tech II EDM emits an ultra-narrow visible laserbeam along the same axis as the telescope’s sighting axis to enable accurate pointing using a distinctlaser spot, pinpoint reflectorless measurement, as well as long-range distance measurement usingprisms or reflective sheet targets.

30% faster

● Distance measurement speed

First-generation RED-tech EDM

RED-tech II EDM

350m (1,140ft.)

170m (550ft.)

200m (650ft.)

100m (320ft.)

White side90% reflective

White side90% reflective

Gray side18% reflective

200m (650ft.)

SET1130R3 • SET2130R3 • SET3130R3 • SET4130R3 (standard models)Class 3R laser products

SET1130R • SET2130R • SET3130R • SET4130R (factory options)Class 2 laser products

±(3 + 2ppm x D)mm

±(3 + 2ppm x D)mm

±(5 + 10ppm x D)mm

±(5 + 10ppm x D)mm

±(5 + 10ppm x D)mm

0.3m (1ft.)

100m (320ft.)

±(3 + 2ppm x D)mm

80m (260ft.)45m (140ft.)

Gray side18% reflective ±(5 + 5ppm x D)mm

0.3m (1ft.)

±(3 + 2ppm x D)mm

● Reflectorless measurement range and accuracy with a Kodak Gray Card

350m(1,140ft.)

0.3m(1ft.)

Conventional optics RED-tech II optics

Sokkia’s newly developed optics system

kes Reflectorless EDM More Powerful Than Ever

Measure long distances by directing the laser beam at a reflector. When using a single AP prism, you canmeasure as far as 5,000m (16,400ft.)* at once, with an accuracy of ±(2 + 2ppm x D)mm. In addition, reflectivesheet targets may be used to get measurements of up to 500m (1,640ft.)** with ±(3 + 2ppm x D)mm precision.Choose from Sokkia’s wide selection of sheet targets to suit your needs. Rotating pin-pole targets, two-pointtarget for measuring hidden points, and many other innovative reflective targets are available.

* In good weather conditions. ** When using RS90N-K.

In the reflective sheet or prism modes, maximum laser output is automatically reduced to0.22mW. This is equivalent to the level of a Class 1 laser. The Series130R also includes asafety filter in the telescope, which protects your eye from the laser beam if you happen tosight a reflective prism or sheet target while in reflectorless mode.

The Series130R employs an ultra small-diameter visible laser to obtain measurements with pinpointaccuracy. Fine objects, as well as the corners of walls and other structures, can be measured precisely.You can also make accurate measurements through obstacles such as chain-link fences and treebranches.

■ Ultra-narrow visible laser for pinpoint accuracy

A

B

C

A Series130R: The ultra-narrow laser beam enables accurate measurements through obstacles such as chain-link fences, tree branches, etc. Broader beam models: ���� ��� ����� � ��� �� ������� �����

��� �� ��������� �����������

CSeries130R: Measurements at small incident angles, such as with manholes on the road surface, are handled with high precision by the ultra-narrow laser measuring beam. Broader beam models:���� ������� ���� ��

�� ������� �� �� ��

��� ������� � ����

������� � ���� �������� ��

����������� ��� �� ���

��� �� ������

BSeries130R: The measuring beam is extremely narrow, so distances to walls and corners can be measured with pinpoint accuracy. Broader beam models: � ���

������� ��� ���� ������ ���

� �� � ��� ��� ����� ��������

�� �������� �����������

C

A

B

■ Long-distance measurement with reflectors

■ Laser-pointer functionThe visible laser beam can be conveniently used as a laser pointer for interior leveling work, verticalalignment, setting out, and other tasks.

■ Sokkia’s original absolute encoders

The Series130R total stations are equipped with Sokkia-developedabsolute encoders. These encoders feature the RAB (RAndom Bi-directional) code technology first used in the SDL30 digital level,which provides high stability and reliability. You do not need to resetfor 0 indexing at the start of a job, so surveying can begin from themoment you turn on the power. Work efficiency is also boosted bythe immediate display of azimuth whenever you restart the totalstation.

LED

Absolute encoder disk

CCD

Encoder diagram

■ Triple-axis compensation for high reliability

Vertical and horizontal angles are compensated for by a dual-axiscompensator that detects the tilt of the total station in two directions.In addition, a collimation function corrects the deviation of thetelescope’s mechanical axis. Working together, these features offermaximum reliability with angle measurements.

■ Superior environmental protectionFeaturing advanced protection against dust and water, theSeries130R total stations are able to withstand harsh environmentalconditions (IP64 compliant).

■ Large internal memory The large internal memory can store approx. 10,000 data points. Itsmultiple job file structure allows you to have 10 job files.

■ CompactFlash card unit (factory option)A card drive for commercially availableCF memory cards (Type I) can be addedas an optional feature. With this carddrive, your memory capacity becomesvirtually unlimited. Approx. 576,000 datapoints can be stored on an 64MB card.Cards up to 512MB are supported.

■ Data and status checks at a glanceEach Series130R total station has a built-in control panel on bothsides of its body. These control panels have a clearly visible LCDscreen that lets you quickly check EDM mode (reflectorless, prism,or reflective sheet target), laser beam mode, guide light function, andmore.

Prism Reflective sheet target

Reflectorless

■ Easy operation with alphanumeric keys, softkeys, and new direct keys

Alphanumeric keys (10 keys) are laid out for easy entry of pointnames, coordinate values, and other information. Softkey functionsare freely assigned by users for their convenience. New direct keysallow on-the-fly access to "configuration", "electronic level" and"EDM returned signal check" screens.

■ Easy target selectionSelecting a target is amazingly simple. You can switch betweenreflectorless, prism, and reflective sheet target modes just bypressing the SFT key in sequence, and the icon of the selectedtarget is displayed on the LCD screen for easy confirmation.

■ Password function for securityThe Series130R provides a password-protection function for securitypurposes. You can assign your own password to the instrument toprevent unauthorized use.

Enhanced Hardware Relia

��� ����������� ��� ���� �� �� ������ �������� ��� ����� ��� ���� � ������ �� �������� ������� � ���� �� ������ �� �� ������ � ��� �� �� ������������ � ��� ����� � ��� ������� � ��� �! ��������� "����� ������� ��������� ������������� � ���� ���

���������� ���� ������ ��

�� �� ������ �������#����� �����$ �

���������� ���� ������ ��

����#����� �����$ %

7 levels: 0 to 6. X: unspecified.

9 levels: 0 to 8. X: unspecified.

*1 Factory option *2 Option

23R

*1 *2 *2

*1

*1

■ Guide Light Unit GDL2 (factory option)

bility and Increased Productivity

The Guide Light Unit GDL2 boosts efficiency with setting-out jobs. Itsguide light is composed of two lights of different colors that areemitted from one aperture. From the left side, you see only a greenlight; from the right, only a red light. And when you see green andred flashing back and forth simultaneously, that means you are onthe telescope sighting direction. The GDL2 has a range of up to150m (490ft.). A special flashing pattern is also included to assistusers with color weakness.

The light may be used up to a range of150m (490ft.).

A special flashing pattern is also includedto assist users with color weakness.

Guide Light Unit GDL2 Visible rangeVisible widthCenter resolution

Green LED (524nm) and Red LED (630nm) (IEC Class 1 LED)1.3m to 150m (4.3ft. to 490ft.)Horizontal & vertical: more than ±4˚; approx. 7m at 100m (23ft. at 320ft.)Within 4'; approx. 12cm at 100m (4.7in. at 320ft.)

The Guide Light Unit cannot be used simultaneously with the laser pointer function.

■ SF14 wireless keyboard (option)The SF14 wireless keyboard has atotal of 37 keys (includingalphanumeric keys, softkeys, andmeasurement controls), to enablequick and easy data entry of pointnames and coordinate values.Because all keyoperations can beperformed with thiswireless keyboard,you won’t need to

touch the total station after it’s been aimed at thetarget. Protection against dust and water isanother advantage, as you can use the keyboardwithout worry in the rain or at a dusty constructionsite (IP44 compliant). The SF14 wirelesskeyboard can also be used with Series030R,Series30R, and Series10 total stations.

■ Sensors for the wireless keyboardExtremely compact sensors are mounted onboth sides of Series130R total stations forcommunication with the optional SF14wireless keyboard. These sensors areextremely resistant to light interference, andhave a wide signal reception range to allowcomfortable use of the keyboard.

■ Two battery types: Ni-MH and Ni-Cd The BDC35A Ni-MH battery* gives you 7 hours of continuous angleand distance measurement, and the CDC70 charger features a built-in refresh function to eliminate memory effect. The optional Ni-Cdbattery (BDC40A) offers longer operation in low temperatures.

* Standard equipment.

Optional accessoriesSF14 wireless keyboard • Guide Light Unit GDL2 (factory option) • CFcard unit (factory option) • CDC41 car cigar sockets charger • BDC40ANi-Cd battery • BDC57 Ni-MH external battery, EDC3A power cable forBDC57 (2m), EDC7A power cable for BDC57(0.5m), CDC14 batterycharger for BDC57 • EDC2A AC adaptor (100 to 240V) • EDC14external battery adapter, EDC5 car battery cable for EDC14, EDC4 carcigarette lighter cable for EDC14 • OF3A solar filter • DE25 diagonaleyepiece • EL7 40x eyepiece • DOC46 printer cable • DOC25 (25 pins,male), DOC26 (25 pins, female), DOC27 (9 pins, female), DOC1 (w/oconnector) interface cables • ACE5 auto-collimation eyepiece • 20"/2mmplate level for SET2130R/2130R3 (factory option)

■ Missing Line Measurement (MLM)At the touch of a key, the Series130R measures horizontal distance,slope distance, height difference and percentage of slope betweentwo points.

■ Remote Elevation Measurement (REM)The Series130R easily determines the height of a point wheredistance cannot be measured directly. Sight a point either directlyabove or directly below the target point, and then sight the targetpoint.

■ 3-D Coordinate MeasurementThe Series130R calculates3-D coordinate values ofmeasuring points anddisplays them either as N, E,Z or E, N, Z.

■ Automatic Azimuth Angle SettingThe Series130R canautomatically set thehorizontal angle to theazimuth of a back sight byusing the coordinates of theinstrument station and theback sight point.

■ ResectionThe Series130R can determine the azimuth and coordinates of anunknown instrument station with 2 to 10 known points. When usingtwo points, measure both angles and distances. When using three ormore points, the distance is not required. Station elevation fromknown reference points (up to 10 points) can also be calculated and

each deviation of multiplereference points is displayed.If a bad point is selected itcan be recalculated, re-observed or replaced with anew point.

NZ

E

Known Station

AzimuthAngle

NZ

E

Instrument Station(known)

NZ

E

Known Station Known Station

Instrument Station(unknown)

AzimuthAngle

■ Offset/DistanceThe Series130R calculatesthe angles and distance, orthe coordinates of themeasuring point by inputtingthe distance and directionbetween the measuring pointand the offset point.

■ Offset/Angle The Series130R automatically calculates the position of measuring

points. First, measure a pointon either side of themeasuring point at the samedistance from theSeries130R instrument. Thensight the measuring point.

■ Two-Distance OffsetWith the use of a 2RT500-K 2-point target, the Series130R canmeasure hidden points easily and efficiently. Set the two-point targeton the measuring point (the target does not have to beperpendicular), measure targets A and B, and input the length

between target B and themeasuring point. TheSeries130R calculates theposition of the measuringpoint in angles and distance,or in coordinate values.

■ Setting OutThe Series130R performsthree-dimensional setting outwith N, E and Z or E, N andZ coordinates. Directions anddistances to the setting outposition are indicated on thescreen.

■ Traverse AdjustmentThe Traverse Adjustment program allows you to specify a sequenceof stations through which a traverse may be calculated andoptionally adjusted. The observations do not have to be made in thesame order as the traverse route.

Offset Point

Measuring Point

NZ

E

A

B

Versatile Functions for Hig

MeasuringPoint

■ Point ProjectionThis program projects a point onto a line. It calculates the distanceand offset of the point relative to the specified baseline, and itcomputes the coordinates of the intersection point, which can thenbe directly set out. Elevations are interpolated where possible. When calculating the measuring point, it's possible to calculate anduse the scaled down coefficient of the distance and surveyed valuethat was calculated using the known coordinate values of 2 points.

FROM POINT

TO POINT

FROM POINT TO POINT MEASURED POINT

OFFSET

■ Area CalculationThe Series130R can usemeasured points or storeddata–up to 50 points intotal–to calculate an area.Area calculations are madewith 3D coordinates, so evensloped surfaces can bemeasured with ease andprecision.

Set-out Line and Point Projection

h Work Efficiency at Diverse Sites

■ IntersectionsIt is possible to find an intersection point between 2 referencepoints by specifying the length and/or azimuth angle of either point.

■ Set-out Line The Set-out line program is used for setting out and checkingalignment of curb lines, construction boards and grades of pipes. Abaseline or an offset from baseline can be defined. When calculating the measuring point, it's possible to calculate anduse the scaled down coefficient of the distance and surveyed valuethat was calculated using the known coordinate values of 2 points.

■ Set Out Arc The Set Out Arc program provides a generalized arc calculator toallow the definition of curves from almost any combination ofparameters. Points along the arc can be coordinated and directly setout.

Instantaneous data transfer between any worksite and your office.

The Series130R can sendsurveyed data to a specifiede-mail address or FTPserver. It can also receivecoordinate data for setting-out from your office computeror FTP server.

Just connect a mobile phone (and modem, if necessary) to theSeries130R using the appropriate cables, establish an Internetconnection, and select the job files. Multiple job files can be sent outsimultaneously. Data should be in the SDR33 or SDR2x format. AllSFX functions can be performed via the Series130R’s operationpanel.

Password protection is available to prevent unauthorized use.

Sokkia Field-info Xpress

Interface cable

Interface cable

Interface cable for your mobile phone

Mobile phone with modem incorporated orlocally supplied

Modem

Fixed-linetelephone

Publictelephone

SFX requires connectivity using a mobile phone with a service providercapable of e-mail data transfer to an external source, as well as an activee-mail account and FTP server. Consult your local telecoms operator forproper equipment and connectivity requirements.

System Diagram

Wireless

■ The ideal partner for data collectorsThe Series130R's two-way communication capability brings out thefull functionality of external data collectors. All operations, exceptfor sighting, can be performed with a data collector, so there is noneed to touch the instrument itself. The Series130R optionally incorporates Bluetooth® wirelesstechnology to enable wireless communication with data collectors.Please consult your local Sokkia representative for availability. This is a factory option.

ModelAvailabilityLaser class*1

Telescope

Angle measurementUnitDisplay resolutions (selectable)Accuracy (ISO17123-3:2001)Measuring timeMeasurement modeAutomatic dual-axis compensatorCollimation compensationFine motion screwsDistance measurementLaser output

UnitMeasuring range(slope distance)

Display resolutions

Accuracy(D=measuringdistance, unit:mm)

Measuring time

Measuring mode (selectable)Atmospheric correction / Prism constant correctionRefraction & earth-curvature correctionScale factor setting / Sea level correction Data storage and transferData storage

InterfaceSFX wireless data transferPrinter outputGeneralDisplayKeyboardSF14 wireless keyboard Laser-pointer functionLaser radiation indicatorGuide Light Unit GDL2Sensitivity of levels

Optical plummetTribrachDust and water protection / Operating temperatureInstrument height / Size with handle and batteryWeight with handle and batteryPower supplyBDC35A detachable battery

BDC57 external Ni-MH battery (optional)

Automatic power cut-off / Resume function

Standard modelsClass 3R Laser ProductFully transiting, coaxial sighting and distance measuring opticsLength: 171mm (6.7in.), Objective aperture: 45mm (1.8in.) (EDM 48mm (1.9in.)), Magnification: 30x, Resolving power: 2.5", Image: Erect, Field of view: 1˚30' (26m/1,000m), Minimum focus: 1.3m (4.3ft.), Reticle glass: ∞ mark printed, Reticle illumination: 5 brightness levels Photoelectrical absolute encoder scanning. Both circles adopt diametrical detection.Degree / Gon / Mil, selectable0.5" / 1", 0.1 / 0.2mg, 0.002 / 0.005mil1" / 0.3mg / 0.005mil0.5s or less, continuousH: Clockwise / Counterclockwise, selectable. 0 set, Hold, Angle input, repetition, available. V: Zenith 0 / Horizontal 0 / Horizontal 0± / Slope in %, selectableDual-axis liquid tilt sensor, Working range: ± 3' (± 55mg)On / Off, selectableFine / Coarse 2-speed motionModulated laser, phase comparison method with red laser diode, coaxial opticsReflectorless mode: Class 3R (max. 5mW)Prism/Sheet mode: Class 1 equivalent (max. 0.22mW)Meters / feet / inches, selectable0.3 to 350m (1 to 1,140ft.) (White side, 90% reflective)0.3 to 170m (1 to 550ft.) (Gray side, 18% reflective) RS90N-K: 1.3 to 500m (1,640ft.), RS50N-K: 1.3 to 300m (980ft.), RS10N-K: 1.3 to 100m (320ft.)CP01: 1.3 to 800m (2,620ft.), OR1PA: 1.3 to 500m (1,640ft.)Under average conditions*4: 1.3 to 4,000m (13,120ft.), Under good conditions*5: 1.3 to 5,000m (16,400ft.)Under average conditions*4: to 5,000m (16,400ft.), Under good conditions*5: to 6,000m (19,680ft.)0.0001/0.001m, 0.001/0.01ft., 1/16 or 1/8in.Rapid single: 0.001m, 0.01ft., 1/8in. / Tracking: 0.01m, 0.1ft., 1/2in.0.3 to 200m (1 to 650ft.): ± (3 + 2ppm x D)mmOver 200 to 350m (over 650 to 1,140ft.): ± (5 + 10ppm x D)mm0.3 to 200m (1 to 650ft.): ± (6 + 2ppm x D)mmOver 200 to 350m (over 650 to 1,140ft.): ± (8 + 10ppm x D)mmFine: ± (3 + 2ppm x D)mm, Rapid single: ± (6 + 2ppm x D)mmFine: ± (2 + 2ppm x D)mm, Rapid single: ± (5 + 2ppm x D)mmRepeat: every 0.9s (initial 1.7s), Single: 1.7sRapid single: 1.8s / Tracking: Every 0.3s (initial 1.6s)Fine (single / repeat / average), Rapid (single), TrackingTemperature / Pressure / ppm input, available. / -99 to +99mm (1mm steps). 0 fixed in reflectorless mode.Yes (K=0.142 / 0.20) / No, selectable0.5 to 2.0 / Yes / No

Approx. 10,000 points with max. 10 job filesCF card unit is available as a factory option.Asynchronous serial RS-232C compatible, Baud rate: 1,200 to 38,400bps / Bluetooth wireless communication is available as a factory option.ProvidedCentronics compatible (with optional DOC46 printer cable)

Alphanumeric/graphic dot matrix LCD, 192 x 80 dots, with backlight, with contrast adjustment, on both faces4 softkeys, 3 direct keys, alphanumeric keys, total 31 keys on both facesOptionalON (auto off in 5 minutes) / OFF, selectable. (Does not work simultaneously with the Guide Light.)YesFactory option20" / 2mmCircular level: 10' /2mm / Graphic LCD level: 3' / outer circle5.5xDetachableConforms to IP64 (IEC 60529:1989) / -20 to +50˚C (-4 to +122˚F)236mm (9.3in.) from tribrach bottom / W 175 x D 171 x H 345 mm (W 6.9 x D 6.7 x H 13.6 in.)Approx. 5.8kg (12.7lb.)6V DCNi-MH rechargeable battery, 2 BDC35A are included as standard accessories.About 7 hours (about 800 points) (single measurement every 30 seconds)About 9 hours (angle measurement only)About 120 minutes per battery

About 29 hours (single measurement every 30 seconds),about 40.5 hours (angle measurement only)Auto-off time is selectable from 30, 15, 10, 5 minutes or none. / Yes

2" / 0.6mg / 0.01mil

30" / 2mm*6

3x

2" / 0.6mg / 0.01mil

30" / 2mm*6

3x

1" / 5", 0.2 / 1mg, 0.005 / 0.02mil3" / 1mg / 0.015mil

0.001m, 0.01ft., 1/8in.

30" / 2mm

5" / 1.5mg / 0.025mil 5" / 1.5mg / 0.025mil1" / 5", 0.2 / 1mg, 0.005 / 0.02mil3" / 1mg / 0.015mil

0.001m, 0.01ft., 1/8in.

30" / 2mm

Factory optionsClass 2 Laser Product

0.5" / 1", 0.1 / 0.2mg, 0.002 / 0.005mil1" / 0.3mg / 0.005mil

Reflectorless mode: Class 2 (max. 0.99mW)Prism/Sheet mode: Class 1 equivalent (max. 0.22mW)

0.3 to 200m (1 to 650ft.) (White side, 90% reflective)0.3 to 80m (1 to 260ft.) (Gray side, 18% reflective)

0.0001/0.001m, 0.001/0.01ft., 1/16 or 1/8in.

0.3 to 100m (1 to 320ft.): ± (3 + 2ppm x D)mmOver 100 to 200m (over 320 to 650ft.): ± (5 + 10ppm x D)mm0.3 to 100m (1 to 320ft.): ± (6 + 2ppm x D)mmOver 100 to 200m (over 320 to 650ft.): ± (8 + 10ppm x D)mm

None

20" / 2mm

5.5x

About 30 hours (single measurement every 30 seconds),about 42 hours (angle measurement only)

Reflectorless*2

(using Kodak Gray Card) With reflective sheet target With mini prisms With 1 AP prism With 3 AP prisms Fine mode

Rapid single / Tracking Reflectorless*2/*3

(Fine mode) Reflectorless*2/*3

(Rapid single mode) With reflective sheet target With AP prismFine mode Rapid single / Tracking

Internal memoryMemory card unit

Plate level Circular / Graphic Magnification

Continuous use per battery at 25˚C (77˚F) Recharging time

Continuous use at 25˚C (77˚F)

*1 IEC 60825-1Amd.2: 2001 / FDA CDRH 21 CFR Part1040.10 and 1040.11 (Complies with FDA performance standards for laser products except for deviations pursuant to Laser Notice No.50, dated July 26, 2001.)*2 Reflectorless range/accuracy may vary according to measuring objects, observation situations and environmental conditions.*3 With Kodak Gray Card White Side (90% reflective)*4 Average conditions: Slight haze, visibility about 20km (12 miles), sunny periods, weak scintillation.*5 Good conditions: No haze, visibility about 40km (25 miles), overcast, no scintillation.*6 20”/2 mm plate level is available as a factory option.

Sokkia is a sponsor of the International Federation of Surveyors

ISO9001 Certified (JQA-0557)http://www.sokkia.co.jp/english/

INTERNATIONAL SALES DEPARTMENT260-63 HASE, ATSUGI, KANAGAWA, 243-0036 JAPANPHONE +81-46-248-7984 FAX +81-46-247-1731

Sokkia is a trademark of Sokkia Co., Ltd. KODAK is a registered trademark of the Eastman KODAK Company. The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Sokkia is under license. Other trademarks and trade names are those of their respective owners.Designs and specifications are subject to change without notice. Product colors in this brochure may vary slightly from those of the actual products owing to limitations of the printing process.

Reflectorless Total Stations SPECIFICATIONSSeries130RSET1130R3 · SET2130R3 · SET3130R3 · SET4130R3 · SET1130R · SET2130R · SET3130R · SET4130R

53R

A-211-E-7-0601-CH-AB Printed in Japan on 100% recycled paper with ecologically safe soy ink.

© 2006 SOKKIA CO., LTD.

■ Standard accessoriessBDC35A rechargeable Ni-MH batteries (2 pcs.) • CDC70 charger with EDC113A/113B/113C powercable • CP7 tubular compass • Lens hood • Lens cap • Plumb bob • Tool kit • Wiping cloth • Vinylcover • Operator's manual • Carrying case • Shoulder strap • Laser caution sign (for Class 3Rmodels only)