surface tension
DESCRIPTION
This presentation has the details about the surface tension of the waterTRANSCRIPT
Surface Tension
Water striders are light (like ants) thus don’t “break” surface
• Ooh! Look at me! I have hydrophobic feet and I weigh less than Fritz does! I’m soooo great!
Even a piece of steel can do this trick if it is small (steel ~ 8x water)
4 H2O molecules
• separated in space from each other
• have partial + and – charges
• what would they do???
but what’s surface tension, really?
4 H2O molecules
• they clump together
• + and – charges snuggle up close
• potential energy of system has dropped
Surface Tension water in bulk has
many binding partners
water at surface has less, has exposed charges left over
potential energy of water at surface is higher
deforming droplet to increase surface area takes work
Surface Tension
E = FX, energy = force * distance
dE = F dX F = dE/dX
e.g. spring energy = ½ kx2, dE/dX = kx = F
Surface Tension
creating surface area in 20C water droplet takes
73 ergs/cm^2 droplet thus
seems springy if mg << l it
dominates and you can walk on water (Vogel pp 72, 104-109)
Surface Tension
surface area in 20C water costs
73 ergs/cm2
= “ ”
Surface Tension
surface area in 20C water costs
73 ergs/cm2
F = dE/dX
can get from F in this apparatus
if film is w by w cm, how much area has been created?
Surface Tension
2 W2
OK so remember this? (steel ~ 8x water)
Floating without floating – The SECRET OF THE STRIDERS REVEALED!!!
= 73 ergs/cm2 = 73 dyne-cm/cm2 = 73 dynes/cm 73 dynes/cm is also like a tear strength if we stacked poker chips on water it might look like below area of chip doesn’t matter so much as the edge (vertical
contributions) lift = perimeter * * sin wait, why sin ? why not pull them all at 90 degrees?
Floating without floating -
is constant of water / air interface, so can’t just “choose” to pull less
surface fails when tension along perimeter of chips exceeds 73 dynes/cm
after that, the water does something else more energetically profitable –
Incidentally – Scaling tie-in - Why droplets are droplet-sized -
mass increases faster than length or area, so above about 1 cm diameter, water droplet mg > l, so more likely to get torn apart by its own weight
Floating without floating - anyway so if the outlines of your feet are long enough for L to
add up to more than your weight (and your contact angle is high) you too can walk on water
Contact Angles
here’s a droplet on a surface -
Contact Angle
here’s a slice of it –
tangent to droplet edge is “contact angle”
why is theta theta?
Contact Angle
balance of forces
surface tension pulls up
gravity & adhesion pulls down
what are the other two?
Contact Angle
F = dE/dX
surface/air & surface/water interfaces also have “surface tension”, in ergs/cm2
moving water edge back and forth incurs energy costs/profits
but units of F are energy/distance, not area?! what’s the deal?
Contact Angle
problem is 3-D
surface tension is force per length
each dL of perimeter contributes dL force
F = dE/dX => dL
dE = dL dX = dA
back to ergs/cm2
Obtuse contact Angles
hydrophobic surface
“gravity & adhesion” is now “gravity & repulsion”
if no gravity, drop leaves
Contact Angle
why doesn’t drop pull or push itself along the surface?
it did when initially set down, it distorted itself until equilibrium reached
edge equilibrium is one thing
equilibrium between (roundness) & gravity (flatness) & surface coverage (adhesion/repulsion) is another factor...
surface adhesion energy
surface adhesion energy
The water at this surface is at a lower potential energy than the bulk water, so deformations that increase this surface area are favorable and spontaneous
Same thing as drop on surface, different geometry
• so fluid scoots along the surface until equilibrium reached
• like water rising in a tube until forces add to mg (gravity) = r2 h g
• surface tension trying to pull water up tube rather than round up a bead
• equivalently - surface energies are being minimized
dE = F dX = dL dX = dA
The End
….. Thank You ……