suppression techniques using x2y as a broadband emi filter · suppression techniques using x2y® as...
TRANSCRIPT
![Page 1: Suppression Techniques using X2Y as a Broadband EMI Filter · Suppression Techniques using X2Y® as a Broadband EMI Filter Bart Bouma Yageo/Phycomp The Netherlands Jim Muccioli Tony](https://reader034.vdocuments.site/reader034/viewer/2022051810/601a69f8ab8956247532c1f3/html5/thumbnails/1.jpg)
1
Suppression Techniques using X2Y® as a Broadband EMI Filter
Bart BoumaYageo/PhycompThe Netherlands
Jim MuccioliTony AnthonyDave AnthonyDale SandersX2Y Attenuators, LLCErie, PA 16506-2972www.x2y.comEmail: [email protected]
2003 IEEE International Symposium on EMC, Boston, MA
![Page 2: Suppression Techniques using X2Y as a Broadband EMI Filter · Suppression Techniques using X2Y® as a Broadband EMI Filter Bart Bouma Yageo/Phycomp The Netherlands Jim Muccioli Tony](https://reader034.vdocuments.site/reader034/viewer/2022051810/601a69f8ab8956247532c1f3/html5/thumbnails/2.jpg)
2
Presentation Outline
• Broadband Filtering of Motors• Internal Construction & Model of X2Y• Other Applications & Testing• Conclusions
![Page 3: Suppression Techniques using X2Y as a Broadband EMI Filter · Suppression Techniques using X2Y® as a Broadband EMI Filter Bart Bouma Yageo/Phycomp The Netherlands Jim Muccioli Tony](https://reader034.vdocuments.site/reader034/viewer/2022051810/601a69f8ab8956247532c1f3/html5/thumbnails/3.jpg)
3
Electromagnetic Noise Sources In Motors
Armature coil
Commutator contacts
Brushes
![Page 4: Suppression Techniques using X2Y as a Broadband EMI Filter · Suppression Techniques using X2Y® as a Broadband EMI Filter Bart Bouma Yageo/Phycomp The Netherlands Jim Muccioli Tony](https://reader034.vdocuments.site/reader034/viewer/2022051810/601a69f8ab8956247532c1f3/html5/thumbnails/4.jpg)
4
Seven Component Motor Filter
The seven component filter design includes (2) 7.5 uh inductors to limit the amount of noise that passes through and then uses (2) x-capacitors, 0.47 uF and 1000 pF, to bypass the noise to the motor case which is grounded. The filter network also uses (2) ferrite beads that provide high impedance at the frequencies of the unwanted noise. The beads’ ferromagnetic material used in the circuit absorbs the noise and dissipates it as heat, due to a time varying magnetic field. The last component in the network is a 0.47 uF cap-varistor placed across the power leads to clamp the noise to 14 volts and bypass any remaining noise to ground.
![Page 5: Suppression Techniques using X2Y as a Broadband EMI Filter · Suppression Techniques using X2Y® as a Broadband EMI Filter Bart Bouma Yageo/Phycomp The Netherlands Jim Muccioli Tony](https://reader034.vdocuments.site/reader034/viewer/2022051810/601a69f8ab8956247532c1f3/html5/thumbnails/5.jpg)
5
Five Component Motor Filter
The five component network starts with (2) ferrite beads that provide high impedance at the frequencies of the unwanted noise and uses a 0.47 uF cap-varistor to clamp the noise to 14 volts. (2) 0.47 uF y-capacitors are also connected from the power leads to motor case ground to bypass the remaining noise to ground.
![Page 6: Suppression Techniques using X2Y as a Broadband EMI Filter · Suppression Techniques using X2Y® as a Broadband EMI Filter Bart Bouma Yageo/Phycomp The Netherlands Jim Muccioli Tony](https://reader034.vdocuments.site/reader034/viewer/2022051810/601a69f8ab8956247532c1f3/html5/thumbnails/6.jpg)
6
Four Component Motor Filter
The four component filter, uses (1) 1000 pF x-capacitor to bypass the noise to ground and the motor case. Then (2) 7.5 uh inductors limit the noise and a second x-capacitor at 0.47 uF bypasses the remaining noise to the motor case which is grounded.
![Page 7: Suppression Techniques using X2Y as a Broadband EMI Filter · Suppression Techniques using X2Y® as a Broadband EMI Filter Bart Bouma Yageo/Phycomp The Netherlands Jim Muccioli Tony](https://reader034.vdocuments.site/reader034/viewer/2022051810/601a69f8ab8956247532c1f3/html5/thumbnails/7.jpg)
7
One Component Motor Filter
The one component filter is a 1410 sized package chip. This chip is configured in what is called an X2Y® layered architecture that combines an unique electrode layering method and uses an internal image plane between capacitor plates to minimize internal inductance and resistance. Alternating electrode layering allows opposing internal skin currents that are essentially 180 degrees out of phase to cancel out. This device was also designed to have its internal mutual inductance fields cancel.
![Page 8: Suppression Techniques using X2Y as a Broadband EMI Filter · Suppression Techniques using X2Y® as a Broadband EMI Filter Bart Bouma Yageo/Phycomp The Netherlands Jim Muccioli Tony](https://reader034.vdocuments.site/reader034/viewer/2022051810/601a69f8ab8956247532c1f3/html5/thumbnails/8.jpg)
8
Filter Performance Comparisons
![Page 9: Suppression Techniques using X2Y as a Broadband EMI Filter · Suppression Techniques using X2Y® as a Broadband EMI Filter Bart Bouma Yageo/Phycomp The Netherlands Jim Muccioli Tony](https://reader034.vdocuments.site/reader034/viewer/2022051810/601a69f8ab8956247532c1f3/html5/thumbnails/9.jpg)
9
Proper GroundingThe importance of connecting both the G1 and G2 terminations is highlighted in the test data below. The land pad under the G1 and G2 terminations of the X2Y component should be continuous. Two viasminimum are required, three vias will lower inductance and improve performance. Two solder connections, one at G1 and one at G2 arerequired.
1 connection
2 connections
A BG1
G2
X
Y
Land Pattern
X2Y
ABoard Surface
Ground Plane
A BG2Board Surface
Ground Plane
Board View
Side
Front
![Page 10: Suppression Techniques using X2Y as a Broadband EMI Filter · Suppression Techniques using X2Y® as a Broadband EMI Filter Bart Bouma Yageo/Phycomp The Netherlands Jim Muccioli Tony](https://reader034.vdocuments.site/reader034/viewer/2022051810/601a69f8ab8956247532c1f3/html5/thumbnails/10.jpg)
10
Single Point Ground
singlepoint ground
G1 & G2 of X2Y
attaches here
![Page 11: Suppression Techniques using X2Y as a Broadband EMI Filter · Suppression Techniques using X2Y® as a Broadband EMI Filter Bart Bouma Yageo/Phycomp The Netherlands Jim Muccioli Tony](https://reader034.vdocuments.site/reader034/viewer/2022051810/601a69f8ab8956247532c1f3/html5/thumbnails/11.jpg)
11
Parallel Ground
Continuous trace placed under G1 & G2 of X2Y
Two grounds used. Solder has been added to improve grounding when screws are tightened.
![Page 12: Suppression Techniques using X2Y as a Broadband EMI Filter · Suppression Techniques using X2Y® as a Broadband EMI Filter Bart Bouma Yageo/Phycomp The Netherlands Jim Muccioli Tony](https://reader034.vdocuments.site/reader034/viewer/2022051810/601a69f8ab8956247532c1f3/html5/thumbnails/12.jpg)
12
Ground Performance Data1812 0.44 uF X2Y
20
25
30
35
40
45
50
55
60
65
0 100 200 300 400 500 600 700 800 900 1000Frequency MHz
dBuV
Ambient No filter 00008D25-1P Motor #2 Motor #2 Modify with X2Y Mounted on bottom
1812 0.44 uF X2Y
20
25
30
35
40
45
50
55
60
65
0 100 200 300 400 500 600 700 800 900 1000Frequency MHz
dBuV
Ambient No filter - Motor #2 Motor #2 Modify with X2Y Mounted on bottom
1812 0.44 uF X2Y
20
25
30
35
40
45
50
55
60
65
0 100 200 300 400 500 600 700 800 900 1000Frequency MHz
dBuV
Ambient No filter 00008D25-1P Motor #2 Motor #2 Modify with X2Y Mounted on bottom
1812 0.44 uF X2Y
20
25
30
35
40
45
50
55
60
65
0 100 200 300 400 500 600 700 800 900 1000Frequency MHz
dBuV
Ambient No filter - Motor #2 Motor #2 Modify with X2Y Mounted on bottom
1812 0.44 uF X2Y
20
25
30
35
40
45
50
55
60
65
0 100 200 300 400 500 600 700 800 900 1000Frequency MHz
dBuV
Ambient No filter - Motor #2 Motor #2 Modify with X2Y Mounted on bottom
Single point groundSingle point ground
Multiple groundMultiple ground
No filterNo filter
![Page 13: Suppression Techniques using X2Y as a Broadband EMI Filter · Suppression Techniques using X2Y® as a Broadband EMI Filter Bart Bouma Yageo/Phycomp The Netherlands Jim Muccioli Tony](https://reader034.vdocuments.site/reader034/viewer/2022051810/601a69f8ab8956247532c1f3/html5/thumbnails/13.jpg)
13
Trace Inductance
M o t o r
0
5
10
15
20
25
30
35
40
45
50
0 100 200 300 400 500 600 700 800 900 1000
Fr e que nc y M H z
Ambient No Fi l ter (cw) 0.2 uF X2Y 1206 (cw) 0.2 uF X2Y 1206 wi th power l eads at X2Y(cw) 0.33 uF X2Y 1410 wi th power l eads at X2Y(cw)
![Page 14: Suppression Techniques using X2Y as a Broadband EMI Filter · Suppression Techniques using X2Y® as a Broadband EMI Filter Bart Bouma Yageo/Phycomp The Netherlands Jim Muccioli Tony](https://reader034.vdocuments.site/reader034/viewer/2022051810/601a69f8ab8956247532c1f3/html5/thumbnails/14.jpg)
14
Internal Construction and Model of X2Y
• Internal Construction• Balanced Performance• Coaxial Behavior• Current Loop
![Page 15: Suppression Techniques using X2Y as a Broadband EMI Filter · Suppression Techniques using X2Y® as a Broadband EMI Filter Bart Bouma Yageo/Phycomp The Netherlands Jim Muccioli Tony](https://reader034.vdocuments.site/reader034/viewer/2022051810/601a69f8ab8956247532c1f3/html5/thumbnails/15.jpg)
15
A
B
ReferenceElectrodes
+ =
Parallel Reference Electrodes
Bypass Capacitor
AB
G1
ReferenceElectrodes
G2
Internal Construction
The X2Y structure consists of:1. A standard bypass capacitor.2. Parallel reference electrodes. 3. Two additional side terminations called G1 and G2.
The side terminations combine with the parallel reference electrodes to form the basic structure. The parallel reference electrodes have properties similar to a Faraday Cage and an Image Plane*.
X2Y® Capacitor
A
BG1G2
*Reference to “Effect of an Image Plane on Printed Circuit Board Radiation” by Robert F German, Henry W. Ott, and Clayton R. Paul, IEEE International Symposium on Electromagnetic Compatibility, Washington, D.C., August 21-23, 1990.
![Page 16: Suppression Techniques using X2Y as a Broadband EMI Filter · Suppression Techniques using X2Y® as a Broadband EMI Filter Bart Bouma Yageo/Phycomp The Netherlands Jim Muccioli Tony](https://reader034.vdocuments.site/reader034/viewer/2022051810/601a69f8ab8956247532c1f3/html5/thumbnails/16.jpg)
16
Balanced Component
Inserting a “Faraday cage” structure inside a bypass capacitor changes an unbalanced, single ended device into a balanced device. “A balanced device is composed of two nominally identical halves.” *
A
B
G1 G2
Cy
Cy
Cx = ½ Cy
+ + + + + + +
+ + + + + + +- - - - - - - -
- - - - - - - -- - - - - - - -
+ + + + + + +
A
B
G1 G2
Cy
Cy
Cx = ½ Cy
+ + + + + + +
+ + + + + + +- - - - - - - -
- - - - - - - -- - - - - - - -
+ + + + + + +
A
B
G1 G2
Cy
Cy
Cx = ½ Cy
+ + + + + + +
+ + + + + + +- - - - - - - -
- - - - - - - -- - - - - - - -
+ + + + + + +
A
B
G1 G2
Cy
Cy
Cx = ½ Cy
+ + + + + + +
+ + + + + + +- - - - - - - -
- - - - - - - -- - - - - - - -
+ + + + + + +
Balance in a single body:• Two tight tolerance Cy
capacitors, typically 1-3%• Equal aging effects• Temperature tracking• Balanced filtering** Needed for high speed circuits
* Balanced Device Characterization, Agilent Technologies, http://cp.home.agilent.com/upload/cmc_upload/tmo/downloads/EPSG084733.pdf (slide#3)
** Differential-to-common-mode conversion, By Howard Johnson, PhD -- EDN, 10/17/2002, http://www.e-insite.net/ednmag/index.asp?layout=article&articleid=CA250820
![Page 17: Suppression Techniques using X2Y as a Broadband EMI Filter · Suppression Techniques using X2Y® as a Broadband EMI Filter Bart Bouma Yageo/Phycomp The Netherlands Jim Muccioli Tony](https://reader034.vdocuments.site/reader034/viewer/2022051810/601a69f8ab8956247532c1f3/html5/thumbnails/17.jpg)
17
Balanced Component Performance
s11
s22
VNA HP 8753E
A
BG1
G2
The X2Y capacitor is measured with a VNA and microwave test fixture from 30kHz-6GHz. By making an s11 and s22 (reflection) measurement we can see the balanced performance of the component from 30kHz-6GHz.
MHz
Deg
rees 0
+180
-180
+90
-90
1 10 100 10000.1
MHz
Deg
rees 0
+180
-180
+90
-90
1 10 100 10000.1
Deg
rees 0
+180
-180
+90
-90
1 10 100 10000.1
26.7967MHzs22: - .03290dBs11: - .02550dB
MHz1 10 100 10000.1
0
Scale 0.1dB/div
26.7967MHzs22: - .03290dBs11: - .02550dB
MHz1 10 100 10000.1
0
Scale 0.1dB/div
26.7967MHzs22: - .03290dBs11: - .02550dB
MHz1 10 100 10000.1
0
Scale 0.1dB/div
![Page 18: Suppression Techniques using X2Y as a Broadband EMI Filter · Suppression Techniques using X2Y® as a Broadband EMI Filter Bart Bouma Yageo/Phycomp The Netherlands Jim Muccioli Tony](https://reader034.vdocuments.site/reader034/viewer/2022051810/601a69f8ab8956247532c1f3/html5/thumbnails/18.jpg)
18
Coaxial BehaviorThe X2Y design is similar to a dual rectangular coaxial structure that was studied and modeled by the National Bureau of Standards*. The reference electrodes form a non-ideal shielded container for each conductor inside the capacitor.
At high frequency, the circuit noise in each capacitor will choose the low impedance path of the reference electrodes and opposing noise currents will cancel, similar to an “Image Plane”.
AB
G1
ShiedElectrodes
X2Y® Capacitor
Two Rectangular Coaxial Transmission Lines (RCTL)
AB
G1
ReferenceElectrodes
X2Y® Capacitor
Two Rectangular Coaxial Transmission Lines (RCTL)
Common Mode Noise Coupling
Differential Mode Noise Coupling
X2Y: Differential and Common Mode
+ =
G2A
BG1
ShiedElectrodes
X2Y® Capacitor
Two Rectangular Coaxial Transmission Lines (RCTL)
AB
G1
ReferenceElectrodes
X2Y® Capacitor
Two Rectangular Coaxial Transmission Lines (RCTL)
Common Mode Noise Coupling
Differential Mode Noise Coupling
X2Y: Differential and Common Mode
+ =
Common Mode Noise Coupling
Differential Mode Noise Coupling
X2Y: Differential and Common Mode
+ =
G2
*Reference to “Theoretical and Experimental Analysis of Coupling Characteristics of Dual TEM Cells” by P.F. Wilson, D.C. Chang, Department of Electrical Engineering, University of Colorado & M.T.Ma, M.L. Crawford, Electromagnetic Fields Division, National Bureau of Standards, Boulder, CO 80303 © 1983 IEEE
![Page 19: Suppression Techniques using X2Y as a Broadband EMI Filter · Suppression Techniques using X2Y® as a Broadband EMI Filter Bart Bouma Yageo/Phycomp The Netherlands Jim Muccioli Tony](https://reader034.vdocuments.site/reader034/viewer/2022051810/601a69f8ab8956247532c1f3/html5/thumbnails/19.jpg)
19
Coaxial Theory
Current flowing in a loop creates magnetic fields 180°out of phase on the signal and signal return conductors. As frequency increases, so do the fields (di/dt). As the fields couple onto opposing conductors they cancel due to mutual inductance.
At high frequency, the shield of coax cable provides a lower impedance signal return than the ground plane. The reduction in loop area results in a maximum of mutual inductance cancellation of high frequency noise.
![Page 20: Suppression Techniques using X2Y as a Broadband EMI Filter · Suppression Techniques using X2Y® as a Broadband EMI Filter Bart Bouma Yageo/Phycomp The Netherlands Jim Muccioli Tony](https://reader034.vdocuments.site/reader034/viewer/2022051810/601a69f8ab8956247532c1f3/html5/thumbnails/20.jpg)
20
Bypass Capacitor
AB
Pwr
Gnd
Current Loop
Current Loop X2Y vs. Standard Cap
Standard capacitors have their inductance in “series” with the board layers and form an inductive loop when mounted on a PCB. The inductive loop degrades the circuit performance. In X2Y every other layer within the single component body is in opposition to cancel the magnetic fields.
X2Y Capacitor
G2
Pwr
Gnd
Current LoopA
BG1
ShieldElectrodes
![Page 21: Suppression Techniques using X2Y as a Broadband EMI Filter · Suppression Techniques using X2Y® as a Broadband EMI Filter Bart Bouma Yageo/Phycomp The Netherlands Jim Muccioli Tony](https://reader034.vdocuments.site/reader034/viewer/2022051810/601a69f8ab8956247532c1f3/html5/thumbnails/21.jpg)
21
Other Applications & Testing
• X & (2)Y’s vs. X2Y Comparison• Computer Power Filtering• Insertion Loss for Connectors
![Page 22: Suppression Techniques using X2Y as a Broadband EMI Filter · Suppression Techniques using X2Y® as a Broadband EMI Filter Bart Bouma Yageo/Phycomp The Netherlands Jim Muccioli Tony](https://reader034.vdocuments.site/reader034/viewer/2022051810/601a69f8ab8956247532c1f3/html5/thumbnails/22.jpg)
22
X & (2)Y’s vs. X2Y Comparison
X2Y is compared to an equivalent discrete circuit using a PCB and HP8753E Vector Network Analyzer (VNA).
(1) X2Y Cap(3) Standard Caps vs.(1) 1206 1nF 50V
(2) 1206 2.2nF 50V
(1) 1206 2.2nF 50V(X value = ½ of 2.2nF)
HP 8753E Network Analyzer Test Board
![Page 23: Suppression Techniques using X2Y as a Broadband EMI Filter · Suppression Techniques using X2Y® as a Broadband EMI Filter Bart Bouma Yageo/Phycomp The Netherlands Jim Muccioli Tony](https://reader034.vdocuments.site/reader034/viewer/2022051810/601a69f8ab8956247532c1f3/html5/thumbnails/23.jpg)
23
X & (2)Y’s vs. X2Y Comparison
Two measurements are made for each DUT. All Ports are terminated with 50 Ohms, either through port connection to the VNA or by SMA termination caps.
(3) Standard Caps (1) X2Y Cap
ACy= 3.49nF
Cy= 3.49nF
Cx= 2.58nF
Cy= 2.75nF
Cy= 2.75nF A
Cx= 1.56nFA1A1
B B1B1 B
ACy= 3.49nF
Cy= 3.49nF
Cx= 2.58nF
A1
B1Cy= 2.75nF
Cy= 2.75nF Cx= 1.56nFA1
B1
A
BB
![Page 24: Suppression Techniques using X2Y as a Broadband EMI Filter · Suppression Techniques using X2Y® as a Broadband EMI Filter Bart Bouma Yageo/Phycomp The Netherlands Jim Muccioli Tony](https://reader034.vdocuments.site/reader034/viewer/2022051810/601a69f8ab8956247532c1f3/html5/thumbnails/24.jpg)
24
X & (2)Y’s vs. X2Y Data
DUT
DUT
The X2Y significantly outperforms standard components in differential mode.
![Page 25: Suppression Techniques using X2Y as a Broadband EMI Filter · Suppression Techniques using X2Y® as a Broadband EMI Filter Bart Bouma Yageo/Phycomp The Netherlands Jim Muccioli Tony](https://reader034.vdocuments.site/reader034/viewer/2022051810/601a69f8ab8956247532c1f3/html5/thumbnails/25.jpg)
25
Computer Power Filtering
I/O cables require filtering. X2Y is working to remove the ferrite from the power cord in this application.
![Page 26: Suppression Techniques using X2Y as a Broadband EMI Filter · Suppression Techniques using X2Y® as a Broadband EMI Filter Bart Bouma Yageo/Phycomp The Netherlands Jim Muccioli Tony](https://reader034.vdocuments.site/reader034/viewer/2022051810/601a69f8ab8956247532c1f3/html5/thumbnails/26.jpg)
26
Development Board Test Set-Up
Development Board for the Motorola 68HC11E1
![Page 27: Suppression Techniques using X2Y as a Broadband EMI Filter · Suppression Techniques using X2Y® as a Broadband EMI Filter Bart Bouma Yageo/Phycomp The Netherlands Jim Muccioli Tony](https://reader034.vdocuments.site/reader034/viewer/2022051810/601a69f8ab8956247532c1f3/html5/thumbnails/27.jpg)
27
Development Board Test Data
![Page 28: Suppression Techniques using X2Y as a Broadband EMI Filter · Suppression Techniques using X2Y® as a Broadband EMI Filter Bart Bouma Yageo/Phycomp The Netherlands Jim Muccioli Tony](https://reader034.vdocuments.site/reader034/viewer/2022051810/601a69f8ab8956247532c1f3/html5/thumbnails/28.jpg)
28
Development Board Test Data
![Page 29: Suppression Techniques using X2Y as a Broadband EMI Filter · Suppression Techniques using X2Y® as a Broadband EMI Filter Bart Bouma Yageo/Phycomp The Netherlands Jim Muccioli Tony](https://reader034.vdocuments.site/reader034/viewer/2022051810/601a69f8ab8956247532c1f3/html5/thumbnails/29.jpg)
29
Development Board Test Data
![Page 30: Suppression Techniques using X2Y as a Broadband EMI Filter · Suppression Techniques using X2Y® as a Broadband EMI Filter Bart Bouma Yageo/Phycomp The Netherlands Jim Muccioli Tony](https://reader034.vdocuments.site/reader034/viewer/2022051810/601a69f8ab8956247532c1f3/html5/thumbnails/30.jpg)
30
Insertion Loss for Connectors
Note: Scale Changes
6GHz10MHz1.5 GHz10MHz
ABX-3 with Ferrites ABX-3 with X2Y® (no ferrites)
![Page 31: Suppression Techniques using X2Y as a Broadband EMI Filter · Suppression Techniques using X2Y® as a Broadband EMI Filter Bart Bouma Yageo/Phycomp The Netherlands Jim Muccioli Tony](https://reader034.vdocuments.site/reader034/viewer/2022051810/601a69f8ab8956247532c1f3/html5/thumbnails/31.jpg)
31
Conclusion
• Discrete Components are Affected at High Frequency by Parasitics
• X2Y is a Single Component for Broadband Filtering Applications– Balanced – Low Inductance– Perform at High Frequencies
• Several Applications of X2Y filters are possible for EMI reduction