SC SERIES

STUMP CUTTER

Operating and Maintenance Manual

1

TABLE OF CONTENTS 1. PRODUCT WARRANTY………………………………………………………….. 3 2. CHECKLIST Dealer’s File Copy…………………………………………………... 4 Customer’s File Copy……………………………………………….. 5 3. INTRODUCTION…………………………………………………………………… 6 4. SPECIFICATIONS…………………………………………………………………. 7 5. SAFETY………………………………………………………………………………. 7-8 5.1 Mandatory Safety Shutdown Procedure…………………………………….. 8-10 6. OPERATION………………………………………………………………………... 10 6.1 Forward……………………………………………………………………… 10 6.2 Attaching to and Detaching From a Skidsteer Loader……………………….. 11 6.3 The Controls………………………………………………………………… 12 6.4 Preparing to Cut a Stump…………………………………………………… 12-13 7. DAILY MAINTENANCE…………………………………………………………... 13 7.1 Tooth Adjustment and Replacement………………………………………… 14-15 7. PARTS……………….……………...……………………………………………….. 16 16 Tooth Pattern…………………………………………………………………. 16 32 Tooth Pattern…………………………………………………………………. 17 SC 19 - 21 & Parts List………………………………………………………….. 18-19 SC Parts Omni & Omni Parts List………………………………………………. 20-21 Stump Cutter Hydraulic & Parts List…………………………………………… 22-29 8. HOST KITS………………………………………………………………………….. 30

Revised 07/18/07

2

3

1. PRODUCT WARRANTY

4

After the Stump cutter has been completely setup and attached to the host machine, inspect the following. Check off each item after the prescribed action is taken.

Check that: ♦ No parts of the unit have been damaged

in shipment. Check for things such as dents and loose or missing parts; correct or replace components as required.

♦ All bolts and fasteners are in place and tightly secured.

♦ All grease fittings have been properly lubricated; see lubrication information in this manual.

♦ All decals are in place and securely attached.

♦ The serial number of your unit is recorded in the space provided on this page.

♦ Then, test run the unit while checking that all components are operating correctly.

I acknowledge that the procedures were performed on this unit as outlined above —————————————————

DEALERSHIP NAME

—————————————————- DEALER REPRESENTATIVE’S NAME

————————————————

DATE CHECKLIST FILLED OUT

—————————————————

2. CHECKLIST DEALER’S FILE COPY 2.1 PRE-DELIVERY

The following checklist is an important reminder of the valuable information that MUST be passed on to the Customer at the time the unit is delivered. Check off each item as you explain it to the Customer. ♦ Give the customer his operators manual. Instruct him to be sure to read and

completely understand its contents BEFORE operating the unit.

♦ Explain and review with him the SAFETY information in this manual.

♦ Explain that regular cleaning and lubrication are required for proper operation and long life. Review with him the lubrication information in this manual.

♦ Explain and review with him the service & maintenance information in this manual.

♦ Completely fill out the owner’s registra-tion, including the customer’s signature and return it to the manufacturer.

I acknowledge that the above points were reviewed with me at the time of delivery. ———————————————————

CUSTOMER’S SIGNATURE

——————————————————— DATE DELIVERED

2.2 DELIVERY

5

After the Stump Cutter has been completely setup and attached to the host machine, inspect the following. Check off each item after the prescribed action is taken.

Check that: ♦ No parts of the unit have been damaged

in shipment. Check for things such as dents and loose or missing parts; correct or replace components as required.

♦ All bolts and fasteners are in place and tightly secured.

♦ All grease fittings have been properly lubricated; see lubrication information in this manual.

♦ All decals are in place and securely attached.

♦ The serial number of your unit is recorded in the space provided on this page.

♦ Then, test run the unit while checking that all components are operating correctly.

I acknowledge that the procedures were performed on this unit as outlined above —————————————————

DEALERSHIP NAME

—————————————————- DEALER REPRESENTATIVE’S NAME

————————————————

DATE CHECKLIST FILLED OUT

————————————————— SERIAL NUMBER

2. CHECKLIST CUSTOMER’S FILE COPY 2.1 PRE-DELIVERY

The following checklist is an important reminder of the valuable information that MUST be passed on to the Customer at the time the unit is delivered. Check off each item as you explain it to the Customer. ♦ Give the customer his operators manual. Instruct him to be sure to read and

completely understand its contents BEFORE operating the unit.

♦ Explain and review with him the SAFETY information in this manual.

♦ Explain that regular cleaning and lubrication are required for proper operation and long life. Review with him the lubrication information in this manual.

♦ Explain and review with him the service & maintenance information in this manual.

♦ Completely fill out the owner’s registration, including the customer’s signature and return it to the manufacturer.

I acknowledge that the above points were reviewed with me at the time of delivery. ———————————————————

CUSTOMER’S SIGNATURE

——————————————————— DATE DELIVERED

2.2 DELIVERY

6

3. I N T R O D U C T I O N

The SC SERIES STUMP CUTTER was designed as an attachment machine for use on skid steer loaders. The information contained in this manual refers only to the Stump Cutting Machine. Information regarding the valves used to control oil flow to the Stump Cutter attachment can be found in the host machine’s manual or in the hi flo installation manual if the host machine is so equipped. The information contained within is provided to assist you in preparing, adjusting, maintaining and servicing your machine. More importantly, this manual provides an operating plan for safe and proper use of your machine. Major points of safe operation are detailed in the safety chapter of this manual. Refer to the table of contents for an outline of this manual. Modern machinery has become more sophisticated and, with that in mind, you must read and understand the contents of the manual COMPLETELY and become familiar with your new machine before attempting to operate it. Terms such as “right” and “left” as used in the manual, are as though the reader is sitting in the host machine’s operator seat and facing the stump cutter. Throughout this manual, information is provided which is set in bold type and introduced by the word NOTE: Be sure to read carefully and comply with the message or directive given. Following this information will improve your operating or maintenance efficiency, help you to avoid costly breakdowns or unnecessary damage, and extend the life of your machine. The Manufacturer and Society of Automotive Engineers have adopted this SAFETY ALERT SYMBOL to pinpoint characteristics that, if not properly followed, can create a safety hazard. When you see this symbol in this manual or on the unit itself, you are reminded to BE ALERT! YOUR SAFETY IS INVOLVED!

The manufacturer reserves the right to make changes or improvements in the design or construction of any part without the obligation to install such changes on any unit previously delivered.

7

4. S P E C I F I C A T I O N S

AP300...................................................................................................12 INCHES (300mm)

Minimum Hydraulic HP…………………... 18 …………………... 30 Swing Width………………………………. 67” (90°)…………………… 67” (90°) Cut Below Ground………………………... 8 1/2” …………………… 8 1/2” Cut Above Ground………………………... 23” …………………… 23” Number Of Teeth…………………………. 16 …………………… 32 Weight ……………………………………. 700 lbs …………………… 796 lbs

BEFORE YOU ATTEMPT TO OPERATE THIS EQUIPMENT, READ AND STUDY THE FOLLOWING SAFETY INFORMATION. IN ADDITION, MAKE SURE THAT EVERY INDIVIDUAL WHO OPERATES OR WORKS WITH THIS EQUIPMENT IS FAMILIAR WITH THESE SAFETY PRECAUTIONS. The Manufacturer always takes the operator and their safety into consideration when designing machinery. Guards are provided on exposed moving parts for the operator’s protection, however, some areas cannot be guarded or shielded in order to assure proper operation. In addition, the operator’s manual and decals on the machine itself warn you of further danger and should be read and observed closely. The SAFETY ALERT SYMBOL above means ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! It stresses an attitude of “HEADS UP” for safety and can be found throughout this operator’s manual and on the unit itself. REMEMBER: The careful operator is the best operator. Most accidents are caused by human error. Certain precautions must be observed to prevent the possibility of injury or damage.

5. SAFETY

MODEL SC19 SC21

8

Please read the rules listed below for safe operation BEFORE you operate this equipment. Use of words CAUTION, WARNING, or DANGER, herein and on the machine itself, signal three degrees of hazard. CAUTION is used for general reminders of good safety practices or to direct attention to unsafe practices. WARNING is used to denote a specific potential hazard. DANGER is used to denote the most serious specific potential hazard.

5.1 MANDATORY SAFETY SHUTDOWN PROCEDURE Work of any type on machinery is always more dangerous when the machine is operating. BEFORE cleaning, lubricating, or servicing this unit, the following MANDATORY SAFETY SHUTDOWN PROCEDURE should ALWAYS be followed: 1 Move host machine’s propulsion control to the neutral position and idle engine down. 2. Shut off oil flow to Stump Cutter.

3. Position Stump Cutter so that it is completely resting on the ground or floor.

4. Engage the host machine’s hand brake. 5. Move the host machine’s throttle to the slow idle position, shut the Engine off and remove the Ignition Key. 6. Relieve hydraulic pressure by moving the Hi-flow and cylinder control levers in both directions

9

REMEMBER ALWAYS IDLE ENGINE DOWN BEFORE SHUTTING OFF OIL FLOW.

ONLY when you have taken these precautions can you be sure it is safe to proceed. Failure to follow the above procedures could lead to death or serious bodily injury! Some diagrams used herein may show Door(s), Guard(s), or Shield(s) open or removed for illustration purposes ONLY! BE SURE that all Door(s), Guard(s), and Shield(s) are in their proper position(s) and securely attached BEFORE operating the Stump Cutter! Read and observe ALL Safety information and Decals on the host machine and Stump Cutter BEFORE operating the unit! In addition, familiarize yourself with ALL of the Safety Devices and periodically check that they are functioning properly! Refer to the SAFETY chapter of the host machine’s operator manual and observe ALL Safety recommendations set forth in that manual! CAREFULLY inspect ALL hydraulic hoses and connections on a routine basis; NEVER use your hand, escaping fluid under pressure can cause serious injury! BE SURE to exercise the MANDATORY SAFETY SHUT DOWN PROCEDURE BEFORE proceeding to do any work on the Stump Cutter! BE SURE the Stump Cutter is properly placed on the ground with the cutting head off the ground, BEFORE attempting to work on the cutting wheel. BEFORE transporting the Stump Cutter, BE SURE to raise the unit completely clear of the ground and turn it off. ALWAYS wear proper clothing and covering when working with or on the Stump Cutter. ALWAYS wear safety glasses or face shield while operating the Stump Cutter.

10

DO NOT attempt to work on the Stump Cutter or host machine with the hydraulics live! BE SURE to relieve the hydraulic pressure, by shutting down the engine and moving all control levers to relieve hydraulic pressure BEFORE attempting to disconnect any hoses or BEFORE proceeding to remove the Stump Cutter from the host machine. DO NOT use the Stump Cutter to push objects, it can be damaged by contact with solid objects, as well as upset the stability of the host machine! DO NOT hit the teeth with a steel hammer as this could cause steel chips to fly, causing injury to the eyes or face. REMEMBER! It is the owner’s responsibility for communicating information on the safe use and proper operation and maintenance of this machine!

6. O P E R A T I O N 6.1 FOREWORD The Stump Cutter must be attached to a host machine equipped to provide the necessary hydraulics and operational controls. As there are many different host machines available, this manual will only deal with the generic operation of the Stump Cutter. Anyone attempting to attach and operate the Stump Cutter must first have the knowledge and skill of operating the host machine’s controls. Information regarding the host machine’s controls and attaching procedure is found in the host machine’s Operators Manual or from its Authorized Dealer.

11

6.2 ATTACHING TO AND DETACHING FROM A SKIDSTEER LOADER

During shipment the swingaway control arm is folded down to reduce shipping height. Before connecting the attachment to your skidsteer loader, remove the loose 1/4” capscrew from the lower pivot and the 1/4” clevis pin from the upper pivot and raise the arms. Replace the 1/4” capscrew and self locking nut into the forward most hole of the lower pivot plate. Tighten bolt to remove any looseness but to allow full travel. After connecting the attachment to the skidsteer loader check that the swingaway arm is located correctly left to right. The lower pivot bracket has extra bolt holes to allow moving. Adjust the upper and lower 1/4” clevis pins into the correct holes to achieve the best location of the hydraulic controls.

WARNING!

BE SURE THE BOOM ARMS ARE ALL THE WAY DOWN AND THE BUCKET DUMP ROLLED ALL THE WAY BACK, WHEN ADJUSTING THE ARMS, TO AVOID ACCIDENTAL CONTACT WITH THE OPERATOR OR SKID STEER CONTROLS!! Drive the skidsteer up to the quick attach of the Stump Cutter and connect up. Exercise the MANDATORY SAFETY SHUTDOWN PROCEDURE before proceeding. After installing hydraulic quick couplers compatible with your skidsteer to the two 3/4” main hoses, connect them to the hydraulic outlets assuring that the hose connected to the “P” port of the valve goes to the pressure outlet of the skidsteer. Detaching is a reversal of this process.

12

6.3 THE CONTROLS After all mechanical and hydraulic connections have been made and the swingaway arm is adjusted properly, raise the cutter wheel off the ground. Make sure all persons and objects are clear of the wheel area. Turn on the skid steer Hi-Flo and/or auxiliary flow, increase engine RPM to approximately 1/2. Once the cutter wheel is turning you will be able to operate the controls. Push the left hand lever down, this should raise the cutter head. Pushing it up will lower the cutter head, operate the cylinder through is full stroke several times to purge any air from this circuit. Pushing the right hand lever down will swing the cutter head to the left, pushing it up will swing the cutter head to the right. Operate the swing cylinder through its full stroke to purge any air from the circuit.

6.4 PREPARING TO CUT A STUMP Drive up to the stump with the cutting head swung all the way to the right. Try to approach the stump from a position that will allow the skidsteer to sit as level as possible left to right. This will allow the cutter head to swing horizontally. Position the cutter head just to the right of the stump. With the back plate approximately vertical lower the loader boom arms unit the stump cutter roller is on the ground. Turn on the Hi-Flo and or the auxiliary flow to the stump cutter. Increase engine to full RPM, make sure the wheel is not contacting the ground. Adjust the cutter head to cut approximately 1 to 1 1/2 inches of stump, swing the head to the left across the top near edge of the stump, lower the head another 1 to 1 1/2 inches and swing the head back to the right. Continue in this manner. If the cutter wheel stalls reduce the depth of cut. As the radial surface of the cut becomes long, move the skidsteer slightly to allow cutting a new area, see sketch. Start new cut here —– or here —

13

Do not move forward into the stump while making a cross sweep. Doing so could result in vibration and motor overload that could cause machine and tooth damage. When cutting surface roots make shallow cuts as large chunks can be broken off and thrown if the cut is too deep. Do not try to make a deep plunge cut unless you have teeth that cross over the wheel. Without them the wheel will rub and grab.

7. DAILY MAINTENANCE NOTE: Careful attention to the daily maintenance routines will go a long way toward ensuring efficient operation. 1. At the start of each day, lubricate the grease fittings at each side of the cutter wheel and top and bottom bearings of pivot shaft. Standard shop gun grease will suffice. 2. Using the correct size wrenches, retighten any loose hardware. 3. Inspect for any loose hydraulic fittings of damaged hoses; retighten or replace as required. 4. Clean away any dirt or chips from the wheel and bearings. 5. Check for dull, broken, bent or loose teeth, replace or tighten as required.

CAUTION: NEVER attempt to do any maintenance to the Stump Cutter while it is running. Exercise the MANDATORY SAFETY SHUTDOWN PROCEDURE BEFORE proceeding.

WARNING: NEVER use your hands to check for hydraulic Leaks. Escaping fluid under pressure can cause serious injury! If injured by escaping fluid, see a doctor at once. If proper Medical treatment is NOT administered IMMEDIATELY Serious infection or reaction can develop!

14

7.1 TOOTH ADJUSTMENT AND REPLACEMENT It is important that the teeth are gauged properly. The correct measurement is 1 1/8” to 1 3/16” from the tip of the tooth to the edge of pocket, parallel to the wheel edge. Improper or uneven gauging can cause extra stress and wear on teeth that are extended out too far or excessive wear to pockets and wheel if gauged to short. It is important to monitor the condition of the wheel while adjusting or replacing teeth. Wire brush or clean the wheel so that it can be inspected closely. Make sure the wheel is not cracked. NEVER use a wheel that shows any sign of cracking!! Look at the bolt holes to see if they are worn oversize or are elongated. If they are, the tooth pockets will rotate during use changing the rake or cutting angle of the tooth causing it to hit the wood flat and not cutting it. The pounding that results causes poor cutting performance, tooth bending or breakage and driveline damage. Also look for damage where the tooth clamps to the wheel. Make sure that when the teeth and pockets are bolted to the wheel, that only the tooth and no part of the pocket touches the wheel. If the pocket touches the wheel there may not be enough clamp force to keep the tooth in place and it could fly out! If any to these conditions occur the wheel must be rebuilt or replaced. The condition of the teeth have a big impact on how fast and how smooth the stump cutter cuts. Teeth that are dull or bent will not cut as well as sharp teeth. Any bent or broken teeth should be replaced. Proper sharpening requires restoring a sharp edge and the proper clearance angle to the shank and carbide tip. To accomplish this a regular grinding wheel must be used to restore the proper clearance angle on the shank. Then use a “Green-Silicon Carbide Wheel” to grind the carbide at the same angle until it has a sharp edge. Using the green wheel on the shank or the regular stone on the carbide is unproductive and will damage the wheels. Always use the right stone for the material it was intended to grind. SEE PAGE 15 FOR SHARPENING DETAILS.

15

The bolts that clamp the pocket-tooth combination should be torqued to 150 to 190 foot pounds. DO NOT OVERTORQUE the bolts, this causes wheel damage and makes it difficult to take the pockets off, start at the lower end of the torque range. If the pockets don’t loosen, then stay at that point. If they do loosen increase the tightening torque to the point where they stay tight. On a new machine or after replacing or adjusting teeth, run the cutter for about 15 minutes on a small to me-dium stump, then re-torque the bolts. If your wheel is worn or uneven in the tooth area, the re-torquing becomes even more important. The careful use of anti-seize on the bolt threads will make disassembly easier.

16

NO

LEFT SIDE R

IGH

T SIDE

1 LT ST

2 LT R

T 3 LT R

T

4 LT R

T

5 ST R

T

6 LT R

T

7 LT R

T

8 LT R

T

16 TO

OT

H PA

TT

ER

N

17

NO

.

LEF

T SI

DE

R

IGH

T SI

DE

1

L

T

ST

2

L

T

RT

3

L

T

RT

4

L

T

RT

5

L

T

RT

6

L

T

RT

7

L

T

RT

8

L

T

RT

9

S

T

RT

10

L

T

RT

11

L

T

RT

12

L

T

RT

13

L

T

RT

14

L

T

RT

15

L

T

RT

16

L

T

RT

32 T

OO

TH

PA

TT

ER

N

18

19

SC 19 & 21 STUMP CUTTER PARTS LIST ITEM # PART # DESCRIPTION QTY 1 54417 Back Plate Assembly 1 2 54461 Stump Cutter Head Assembly 1 3 54453 Stump Cutter Pivot Shaft 1 4 54458 Upper Bearing Mount 1 5 54732 Roller 2 6 54804 Roller Shaft 1 7 54065 Hydraulic Cylinder 2 8 54478 Rod End Pin Lift Cylinder 1 9 54477 Base End Pin Lift Cylinder 1 10 54474 Head Lift Pivot Pin 1 11 54468 Pivot Shaft Bearing 2 12 30C-08* 1/2 Nylok Nut 4 13 14C-16 SAE 1" Flat Washer 6 14 13A-0640 Cotter Pin 6 15 13A-0640 Cotter Pin 1 16 50A-0812 * 1/2x1 1/2 HHCS 4 17 50A-0516 * 5/16"x2" Hex Head Cap Screw 4 18 14C-05* 5/16" SAE Flat Washer 4 19 30C-05* 5/16" Nylon Lock Nut 6 26 54412 SC Cutter Wheel 1 28 54868 QD Bushing - 1 15/16" 1 29 54818 Threaded Pockets (SC 19) 8 29 54820 Threaded Pockets (SC 21) 16 30 54819 Counterbored Pockets (SC 19) 8 30 54821 Counterbored Pockets (SC 21) 16 31 51D-1016* Teeth Bolts (SC 19) 16 31 51D-1020* Teeth Bolts (SC 21) 32 32 54812 Straight Teeth (SC 19) 2 32 54815 Straight Teeth (SC 21) 2 33 54813 RH Teeth (SC 19) 7 33 54816 RH Teeth (SC 21) 15 34 54814 LH Teeth (SC 19) 7 34 54817 LH Teeth (SC 21) 15 35 54867 Bearing 1 15/16 2 36 54870 Wheel Shaft - 1 15/16" 1 38 50A-1012 5/8"x1 1/2" Hex Head Cap Screw - Motor 2 39 54414 Motor Adapter 1 40 See Spec Motor 1 41 55014 Seal Kit M51 Motor 1 41 56001 Seal Kit M76 Motor 1 42 50A0512* 5/16"x1 1/2" Hex Head Cap Screw 3 43 14A-05* Lock Washer 3 44 30C-10 5/8" Nylok Nut 4 45 50A-1016* 5/8"x2 Hex Head Cap Screw-offside 4 46 50A1014* 5/8"x1 3/4" Hex Head Cap Screw-Motorside 4 47 14A-10* 5/8" Lock Washer (SC 21) 4 * NOT SHOWN * 54825 Hose Clamp Bracket 1 54047 1/4" Hose Clamps 2 54048 1/4" Clamp Plate 2 54826 3/4" Hose Clamp 1 54827 3/4" Clamp Plate 1 15003 Knob 1 .

20

21

Stump Cutter Parts List OmniS/N 9029, 9606, 9082, 9094, 9099, & UP

ITEM P/N DESC QTY ITEM P/N DESC QTY

1 54417 Plate Back Assy 1 29 54818 Pocket Thrd 82 56109 Head Assy 1 29 54820 Pocket Thrd 163 54453 Pivot Shaft 1 30 54819 Pocket CB 84 54458 Mount Bearing 1 30 54821 Pocket CB 165 54732 Roller 2 31 51D-1016 Teeth Bolt SC19 166 54804 Shaft Roller 1 31 51D-1020 Teeth Bolt SC21 327 54065 Hyd Cyl 2 32 54812 Tooth Str SC19 28 54478 Pin Lift Cyl Rod End 1 32 54815 Tooth Str SC21 29 54477 Pin Lift Cyl Base End 1 33 54813 Tooth RH SC19 7

10 54474 Pin Head Lift Pivot 1 33 54816 Tooth RH SC21 1511 54468 Bearing Pivot Shaft 1 34 54814 Tooth LH SC19 712 30C-08 Nut Nylok 1/2-13 5 34 54817 Tooth LH SC21 1513 14C-16 Washer Flat SAE 1" 5 35 56103 Bearing Cup&Cone Small 114 13A-0640 Pin Cotter 6 36 56104 Bearing Cup&Cone Large 115 56094 Wheel Assy SC19 1 37 56105 Seal Protector 116 50A-0812 HHCS 1/2-13x1 1/2" 5 38 55847 Hub (Part of Wheel 117 50A-0518 HHSC 5/16-18x2 1/4" 4 39 56106 Nut Flanged 118 14C-05 Washer Flat SAE 5/16" 4 40 Motor See Spec 119 30C-05 Nut Nylok 5/16-18 6 41 55014 Kit Seal M51 Motor AR20 55559 Spindle & Hub Assy 1 41 56001 Kit Seal M76 Motor AR21 56096 Shaft 1 NOT SHOWN22 56097 Seal 1 20/40 56113 O'Ring Motor to Spindle 125 56100 Lock Nut Bearing 1 54825 Bracket Hose Clamp 126 56101 Washer Lock 1 54047 Clamp Hose 1/4" 227 1.15E-04 Plug Pipe 1 54048 Plate Clamp 1/4" 228 Housing Spindle 1 54826 Clamp Hose 3/4" 1

54827 Plate Clamp 3/4" 1

22

23

STUMP CUTTER HYDRAULIC PARTS 55763 ITEM # PART # DESCRIPTION QTY 1 55408 Valve Complete Sun 1 1 55277 Seal Kit for 55408 Valve AR 1 55229 Valve Block Only 1 2 54845 Valve Priority .3 GPM 1 3 55231 Valve Check PB 1 4 55230 Valve Check 2 5 55228 Valve 2 Spool BLB 1 5 55929 Spool Seal BLB 4 6 54065 Cylinder Depth/Swing 2 7 Motor - See Motor Spec 1 7 56609 Motor Shaft Bearing M51 1 8 111E-1212 Adapter Str JICM/SAEM 3 9 111E-0404 Adapter Str JICM/SAEM 3 10 111H-08 Plug SAE 2 11 111E-0406 Adapter Str JICM/SAEM 5 12 111B-0406 Adapter 90 Deg JICM/SAEM 1 13 110R-0404 Adapter 90 Deg JICM/NPTM 3 14 111B-1212 Adapter 90 Deg JICM/SAEM 3 15 110G-0604 Adapter Str JICM/NPTM (SC21) 1 17 112B-1212 Adapter 90 Deg JICFS/JICM 1 18 55018 Orifice Adapter 90° 1 19 111H-0404 Plug SAE 1 20 55178 Hose 1/4"x51" PB 2 21 55880 Hose 1/4"x61" Rod Swing Cylinder 1 22 55500 Hose 1/4"x81" Base Depth Cylinder 1 23 55501 Hose 1/4"x98" Rod Depth Cylinder 1 24 55499 Hose 1/4"x48" Base Swing Cylinder 1 25 54726 Hose 3/4"x95" Valve to Motor 1 26 54727 Hose 3/4"x101" Valve to Motor 1 27 55279 Lever Valve 2 28 55264 Cover BLB Valve 1 29 55253 Bracket Sun Valve 1 30 SEE HOST KITS 31 55033 Seal Kit Hydraulic Cylinder AR 32 55612 Pivot Box BLB Valve AR 33 55014* Kit Seal M51 Motor AR 34 56001* Kit Seal M76 Motor AR * Not Shown

24

25

56984 SC UNIVERSAL 3 LINE HYD KIT PARTS

ITEM P/N DESCRIPTION QTY

1 56708-2 Directional Valve 2 Function Incs, 2,3,4,5, 6,40&41 12 56504 4 Way Cartridge Only 23 55611 Coil & Connector 54 54893 PO Check Valve 25 56505 Blocking Valve Cartridge Only 16 56905 Relief Valve Cartridge Only 17 55140 Sun Valve Assy Incs,Items 8 thru 11 18 55229 Valve Block Only 19 55231 Check Valve PB 110 55230 Check Valve Anticav & Return 211 55232 Priority Valve 112 Motor See Motor Spec 113 54065 Swing Cyl 115 54065 Depth Cyl 116 111E-1212 Adap Str JICM/SAEM 417 111B-1212 Adap 90 Deg JICM x SAEM 218 54727 Hose 3/4x101" 119 110G0604 Adap Str JICM/BSPPM 120 112B-0606 Adap 90* JICM/SAEM 121 111B-0404 Adap 90* JICM/SAEM 1022 110R-0404 Adap 90* JICM/NPTM 423 54726 Hose 3/4x95" 224 56908 Tube PB 125 56909 Tube Valve Pressure 126 56910 Tube Valve Return 127 Hose 1/4x Swing Cyl Rod 128 Hose 1/4x Swing Cyl Base 131 Hose 1/4x Depth Cyl Base 132 Hose 1/4x Depth Cyl Rod 133 See Host Kit 134 55033 Seal Kit Hyd Cyl AR35 55014 Seal Kit M51 Motor AR35 56001 Seal Kit M76 Motor AR35 56609 Motor Shaft Bearing AR36 56911 Seal Kit 56708-2 Valve AR37 55277 Seal Kit 55140 Valve AR38 56711 Valve Bracket 139 56712 Valve Cover 140 56576 Cavity Plug 3 Way 141 56577 Cavity Plug 4 Way 1

26

27

57140 CABLE JOHN DEERE 300 SERIES

SOCKET COLOR FUNCTION PLANER STUMP CUTTER C Red Slide LT. Swing LT. G Green Slide RT Swing RT F Blue Depth Up Depth Up H Brown Depth Dn Depth Dn D Yellow Tilt LT NA E White NA Gray Power Beyond A Black Ground

55350D CABLE CASE 400 SERIES NEW HOLLAND

JOHN DEERE PRE 300 SERIES

SOCKET COLOR FUNCTION PLANER STUMP CUTTER C Red Slide LT Swing LT D Yellow Slide RT Swing RT H Brown Depth Up Depth Up G Green Depth Dn Depth Dn E White Tilt LT NA F Blue Tilt RT NA Gray Power Beyond B Black Ground

28

SWINGAWAY ARM ASSEMBLY

ITEM # PART # DESCRIPTION QTY 1 55264 Valve Cover 1 2 55228 BLB Spool Valve 1 3 55531 Sliding Arm 1 4 54736 Horizontal arm 1 5 15003 Knob 1 6 54735 Vertical Arm 1 7 54734 Lower Bracket 1 8 50A-0624 3/8” x 3” HHCS 2 9 30C-06 3/8” Nyloc Nuts 2 10 50A-0422 1/4” x 2 3/4” HHCS 2 11 30C-04 1/4” Nyloc Nuts 2 12 10C-0424 1/4” x 3” Clevis Pin 2 13 55279 Lever (BLB Type) AR 13 54184 Lever (Cable Type) AR 14 55612 Pivot Box (BLB Type) AR 14 54189 Pivot Box (Cable Type) AR ** 54730 SWINGAWAY KIT—ALL ITEMS ABOVE

29

30

STUMP CUTTER HOST KITS

57533 NEW HOLLAND-JOHN DEERE-CAT-KOMATSU-BOBCATCASE 400- CASE BIC SHF- SC21 HOST KIT

Part # Description Qty Cost Total Cost55900 3/4 x 72” Hose 255300 3/8 x 180” Case Drain Hose 1111E-1212 Adapter 2111E-0608 Case Drain QC Adapter 1

57534 CASE 1845 - CASE XT - GEHL - JCB - MUSTANG SC21 HOST KIT

Part # Description Qty Cost Total Cost57044 3/4 x 100” Hose 255300 3/8 x 180” Case Drain Hose 1111E-1212 Adapter 2111E-0608 Case Drain QC Adapter 1

57533LF NEW HOLLAND - JOHN DEERE - CAT - BOBCAT CASE 400 - SC19 HOST KIT

Part # Description Qty Cost Total Cost55900 3/4 x 72” Hose 2

111E-1212 Adapter 2

57534LF JCB - KOMATSU - CASE BIC SHF SC 19

Part # Description Qty Cost Total Cost57044 3/4 x 100” Hose 2111E-1212 Adapter 2

3348 S. Hoover • Wichita, KS 67215 • 316-946-5885

P/N 55626