study of aerodynamic effect of spoiler on a car
TRANSCRIPT
Study Of Aerodynamic Effect Of Spoiler On A
CarProject Presentation
UNDER THE GUIDANCE OFPROF. NIRUPAM ROHATGI
ByAbyn Koshy MathewsPradip Kumar Swain
Vinay Suthar
INTRODUCTION
• Nowadays everyday cars are changed by their owners to make the look sportier.
• Aerodynamic properties of the car given by the designer are not enough to offer the required down force and handling at high speeds.
• Extra parts are added to offer greater drag reduction to the car and at the same time enhance the stability.
• Our focus is on the rear spoiler.
PROBLEM STATEMENT
• When a driver drives his or her car in high speed condition(>110 km/hr)• high tendency to lift over• once the air makes its way to rear window, the notch created by the window
dropping down to the trunk leaves a vacuum or lower pressure space that the air is not able to fill properly.
• and the resulting lower pressure creates lift that then acts upon the surface area of the trunk
• To reduce lift that acted on the rear trunk, a rear spoiler can attach on it to create more high pressure
PROJECT OBJECTIVE• investigate the effects of aftermarket rear spoiler to the car
aerodynamic drag and lift.• by estimate the value of CD and CL • The differences between car with and without spoiler can be
determined • Tow models of rear spoilers will be chosen and the 3-D models will
be built in CAD software according the actual dimension. • analyzed in CFD software to estimate the value of CD and CL• which rear spoiler either reduce drag or reduce lift force, or reduce
both or not can be determine
PROJECT DESCRIPTION• An investigation on effects of rear spoiler to car aerodynamic drag
and its stability will be done by estimate the value of CD by doing some CFD analysis
• several designs will be selected to build up model in CAD software • The models will built up according its actual dimension to make
sure any errors during analyzing can be avoided • models then will be analyzed in CFD to estimate value of drag force
and lift force• From the value of both forces, the value of CD and CL can be estimate
and the data then interpret into graph or scatter plot and also into bar chart
General Aerodynamics Concepts
• Bernoulli’s Equation : p + ½ ρ v2 + γ z = constant along streamline
Fig - Pressure and velocity gradient in the air flow over
Drag and Lift concept
1. Shear stress which act parallel to the body surface and contributes only to drag.
2. Pressure which acts normal to the surface is responsible for a vehicle’s lift and part of drag.
dFx = ( p dA) cos θ + ( τw dA) sin θ
dFy = - ( p dA) sin θ + ( τw dA) cos θ
AERODYNAMICS FORCES
DA = ½ ρ v2 CD A Where CD = coefficient drag [dimensionless]A = frontal area [m2]ρ = density of air [kg/m3]v = velocity of vehicle [m/s]
Drag Force
Lift forceLA = ½ ρ v2 CL A LA = lift force CL = coefficient of lift A = frontal area
Downforce
Downforce is created when air moves through and over parts of the car.
MODELING
• The models will build up in CAD software• SolidWorks will be use to build up the model• the model will be design according the actual dimension to make
sure it can produce an approximately accurate• it also must fix with the base line model that will be use• Airfoil spoilers are used.
BASE LINE MODEL
REAR SPOILER MODEL
• 2 different spoiler styles have been used.
• “wing” style spoiler, which was mounted 23 cm above the
• on the other hand the second spoiler was mounted edge of the rear side of the vehicle without leaving a gap between spoiler and the surface of vehicle
• The models of both vehicle and two different spoilers have been made using the software called SolidWorks to CAD format for numerical .
VIRTUAL WIND TUNNEL
• Around the 3d cad model a virtual wind tunnel is made with the help of inventor.
• The complete domain was divided to half using a symmetry plane (YZ plane).
CFD SOLVER BOUNDARY CONDITION
Boundary Conditions (for all cases and benchmarks)
Velocity Inlet Magnitude and Direction 30m/s (Positive Z-direction)
Turbulence Intensity 1.00%
Pressure
Outlet
Gauge Pressure magnitude 0 Pascal
Gauge Pressure direction Normal to boundary
Turbulence Specification Method Intensity and Viscosity Ratio
Backflow Turbulence Intensity 10%
Wall Zones No Slip
Symmetry No Slip
Fluid
Properties
Fluid Type Air
Density 𝜌 = 1.2 kg/m3
CFD SIMULATION
• The following cases which have to be simulated:
• Case #1: Vehicle model without rear-spoiler.
• Case #2: Vehicle model with the first rear-spoiler design. • Case #3: Vehicle model with the second rear-spoiler design.
Velocity distribution of flow for case #1
Velocity distribution of flow for case #2
Velocity distribution of flow in the symmetry plane for case #3
• As we see in the there were two different recirculation zones .
• There is only one recirculation zone.
Cd graphs
• There was significant change in terms of drag force when comparing case #1 and case #2.
• Case #3 was not considered.
Cl graphs
RESULTVelocity(km/h)
Drag Force (N) Lift Force (N) CD CL
70 241.41 -224.69 0.232 -0.2160
80 294.75 -274.42 0.233 -0.2170
90 353.50 -329.12 0.234 -0.2182
BLM car without Rear Spoiler
Velocity(km/h)
Drag Force (N) Lift Force (N) CD CL
70 199.72 -276.69 0.1920 -0.2660
80 243.92 -337094 0.1931 -0.2675
90 292.55 -405.31 0.1945 -0.2680
BLM car with Spoiler #1
Velocity(km/h)
Drag Force (N) Lift Force (N) CD CL
70 225.73 -382.8 0.2170 -0.368
80 275.69 -467.53 0.2182 -0.3695
90 330.64 -560.73 0.2193 -0.370
BLM car with Spoiler #2
CONCLUSION
• The spoiler used in case #2 exhibited a significant reduction in drag force and in small increase negative lift force.
• The spoiler used in case #3 displayed a relatively smaller reduction in drag force but a huge increase in negative lift force.
• If safety is major concern , then handling of car would much superior of spoiler in case# 3 and would be selected for the design of the car.
FUTURE SCOPE
• Companies such as Porsche, Bugatti or Mercedes have been using different technologies for spoilers.
• A type of such technology is the hydraulic spoiler.• This is currently being used in Bugati Veyron.
REFERENCES
• Carr G.W. The Study of Road Vehicle Aerodynamics, Using Wind Tunnel Models. Paper 14, Proc. 1st Symp. Road Vehicle Aerodynamics, London, 1969.
• Website:* http://www.nasa.gov/audience/forstudents/5-8/features/what-is- aerodynamics-58.html.• Website: http://www.grc.nasa.gov/WWW/K-12/airplane/boundlay.html.• Website : http://en.wikipedia.org/wiki/Bernoulli's_principle• Website : http://www.slideshare.net/pparmaei/aerodynamic-carsscience• Website : http://www.slideshare.net/sharadadevi79/pr-2-33068013• Website :
http://help.autodesk.com/view/SCDSE/2014/ENU/?guid=GUID-94E433C2-1580-4575-A6FA-2E7F22A23EB6
• Website : http://help.autodesk.com/view/SCDSE/2014/ENU/?guid=GUID-3AF255C7-4F5B-4DCB-825A-726698D50510
• Website : http://help.autodesk.com/view/SCDSE/2014/ENU/?guid=GUID-BC3E47DC-6626-41C6-974F-4D5676FAE066