street designcms.esi.info/media/documents/66566_1423822150331.pdf · web site: 01509 815335 01509...

UK street furniture designers & manufacturers

Street Designestablished in 1986

As UK based, designers and manufacturers,Street Design can manufacture and supply theBournemouth, all metal planters, to suit yourspecific requirements.

The design, allows you to specify individualfree-standing planters, available in 2 plansizes and 2 heights.

Choose from a range of accessories to ensurethat the Bournemouth planters aremanufactured to suit your specific scheme.

Large Bournemouth tree planters, 1000mm high, with powder coated mild steel planter walling panels and dull polishedstainless steel top capping

Bournemouth planter product details

Bournemouth planter product specification

Bournemouth planter material finishes

Bournemouth planter accessories

Bournemouth planter material specification

Bournemouth planters are suitable for:

tree plantersmoveable plantersfeature plantersall metal planters

Watering system accessories

Adjustable feet accessory

LED Lighting accessories

BOURNEMOUTH planter

Street Design LimitedUnit 47Hayhill Industrial EstateBarrow upon SoarLeicestershire LE12 8LD

Contact us:Telephone:Fax:Email:Web site:

01509 81533501509 [email protected]

Ref: 01/ABournemouth planter care and maintenance

The Bournemouth planter, is an all metal planter,available in a choice of 2 plan sizes and 2heights.The plan shape is a Reuleax triangle, a threesided shape with curved sides and roundedcorners.The planter walls are polyester powder coatedmild steel and the top capping will be dullpolished stainless steel.A number of planter accessories are available toensure that the Bournemouth planter is suitablefor your specific scheme.

Construction

Key

a 2mm pre-galvanised mild steelb 130mm wide x 8mm thick stainless steelc Curved FSC treated softwood framedef

4mm thick Marine grade plywood75x50x3mm mild steel RHS48.3 Ø x 3mm mild steel CHS

g 88.9 Ø x 5mm mild steel foot plateh 18mm thick FSC treated plywoodI Geotextile membrane filter lining

BOURNEMOUTH planter

PRODUCT DETAILS

General

Section thro’ planter

The planter comprises of a mild steel base ontowhich the planter walls are fixed. The planterwalls consist of a number of curved treatedsoftwood frames, with pre-galvanised mild steelfixed on the outside and a Marine grade plywoodskin, fixed on the inside.After assembly, a treated plywood floor is fittedbefore being fully lined with a geotextilemembrane.To finish off the planter, a dull polished stainlesssteel capping is screw fixed to the top of thetimber wall frames, using stainless steel securityscrews.

Standard foot type

Optional foot type

M30 adjustable legs are screw fitted to bolt onadjustable foot plates, that are fully welded to theunderside of the galvanised mild steel base.




Ref: 10/A

Large Bournemouth planter - overall dimensions

Medium Bournemouth planter - overall dimensions

The large Bournemouth planteris available in 2 heights;800mm and 1000mm high,above finished ground level

Large Bournemouth planter - overall dimensions

The medium Bournemouthplanter is available in 2 heights;800mm and 1000mm high,above finishedground level

aa

b

c c

d d

e

f fg g

h

i

As standard, the planter feet will be an integralpart of the fully welded mild steel base.The feet consist of 48.3 Ø x 3mm thick mild steeltube with a fully welded foot plate. The foot platewill be 88.9 Ø x 5mm thick mild steel.

PRODUCT SPECIFICATION

All Street Design products are designedand manufactured using only quality,durable materials, construction details andfixings, to provide a long-lasting, durablelife expectancy.

Timber policyAll treated softwood planters are manufactured using materials obtained from growers whooperate under the Forest Stewardship Council (FSC).All iroko hardwood planters are manufactured using materials obtained from growers whooperate under the Forest Stewardship Council (FSC).

Large Bournemouth planter Large Bournemouth planters inRAL 9003, white

Construction

Assembly

Materials

Standard finish

Options

Accessories

The pre-galvanised mild steel planter bodywill have a polyester powder coated finish.The stainless steel top capping will have adull polished finish.

Grade 304 stainless steel sheet. Mild steelangle, flats and hollow section.Pre-galvanised mild steel walling panels.Marine grade plywood lining.FSC treated Eucalyptus plywood.Planters will be fitted with a geotextile filterfabric lining, which allows the water todrain through the planter, while retainingthe fill material.

Planters will be delivered to site fullyassembled for off loading and positioningon site.

Bournemouth planters are manufacturedto order.Before we can manufacture the planters,we need to know the following:• plan size of planters• heights• details of accessories required

To enhance your Bournemouth planterand create a product that is suitable foryour specific application, you can addfrom a range of planter accessories.

Adjustable feetWatering systemIntegral bench seating

Base skirting

•••• LED lighting•• Pergola structures• Trellis panels

BOURNEMOUTH planter

Large Bournemouth planters,loaded, ready for delivery




Ref: 11/A

BOURNEMOUTH planter

Tree anchor fittingsBournemouth planters can be manufactured andsupplied to include a range of optionalaccessories. Planters can incorporate; adjustablefeet, tree anchor fittings, base skirtings, wateringsystems, bench seating, LED lighting, pergolasand trellis panels.

Adjustable feet

Watering system

Moveable planters

Bournemouth planters can be supplied with a fullinternal steel frame allowing the planters to bemoved whilst fully planted. The steel frameprovides additional strength and ensures suitablesupports for the forklift tines.

Spalding curved planter bench in FSCtreated redwood with a stained finish

M30 adjustable feet

Bournemouth planters can incorporate treeanchor points. They can be fitted at the bottom ofthe planter to help support the root ball and theycan be fitted at the top of the planter to helpprovide support for the tree.The tree anchors are manufactured as part of theinternal mild steel frame.

Bench seating

ACCESSORIES

Integral planter benches, with or withoutarmrests, can be supplied with Bournemouthplanters. As standard 1 bench design is available.Other designs can be included upon request. TheSpalding bench consists of timber slats. Thetimber slats will be bolted onto galvanised mildsteel frames, attached to the planter sides.Benches can be fitted to 1, 2 or 3 sides to suityour requirements. As standard the brackets willhave a galvanised finish. As an optional extra,they can be polyester powder coated.

Mona watering system

Pergola structures and trellis panels

Pergola structures and trellis panels can beintegrated into the planter construction. Pergolasand trellis allow high level planting and createshading for seating areas.

Medium planter bench configurations

L1Sbench on 1 side

L2Sbench on 2 sides

L3Sbench on 3 sides

LED lighting

Both white and coloured LED lighting can beincluded in the manufacture of the Bournemouthplanter. Lighting can be incorporated into thesides or the base of the planter. It can be utilisedto illuminate the planting or the area around theplanter.See separate page for LED Lighting details.

White LED ‘plant’ lighting

Bournemouth planters can be manufactured withoptional adjustable feet to allow the planter to beheight adjusted to ensure that the top of theplanter is level. The adjustable feet, allow theplanter to be levelled after relocation.See separate page for Adjustable Feet details.

Bournemouth planters can be supplied with achoice of 2 watering systems. Street Design cansupply either a reservoir system, with filler pipe orthe Mona, subterranean tank system.See separate page for Watering System details.




Ref: 20/A

M2Sbench on 2 sides

M3Sbench on 3 sides

M1Sbench on 1 side

Large planter bench configurations

BOURNEMOUTH planter

WATERING SYSTEMS




Watering System 1 - Street Design reservoir system

The Street Design watering accessory is areservoir system with hydroleca sacks, thatmaximises the available water.

The system ensures the optimum use of thewater and nutrients, delivering the maximumquantity directly to the roots of the plants,resulting in improved root development andoptimal plant growth.

300 micronpolythene liner

Section thro’ planterwith Watering System 1

Watering System 2 - MONA subterranean tank system

Planter ready for soil and planting

Water storage tanks and filler pipe

Completed planter

Mona watering systemFactory fitted into planter / tree container

The Mona Plant System (MPS) is an advanced, wellproven and easy to use subterranean irrigationsystem. It is the cost effective and environmentallyfriendly solution for both interior and exteriorlandscaping.

The Mona Plant System ensures that the water andnutrients are delivered in the right quantity to theroot of the plants, resulting in improved rootdevelopment and optimal plant growth.

General

Factory installation

All necessary water tanks, pipes, end caps and airpipes with level indicator, are factory fitted into theplanters / tree containers, prior to delivery.

Ensure that the distance between the top of the linktank and the lowest part of the root does not exceed150mm.

Filling planters

The system consists of storage tanks, flexible linkingpipes and a flexible filler pipe with filler pipe cap.The system delivers water directly to the roots viacapillary action, eliminating water wastage. Thisencourages deep root growth, improving long termdrought resistance. The cap and lid provides aneasy access point for watering and soluble fertiliserapplication.Installation

General

The system consists of a 300 micron thick blackpolythene liner, hydroleca (pulverised ashgranules) sacks and a rigid plastic filler pipe.

The system delivers water directly to the roots via50mm diameter, rigid plastic pipe, eliminatingwater wastage. This encourages deep rootgrowth, improving long term drought resistance.The high level filler pipe provides an easy accesspoint for watering and soluble fertiliserapplication.

Planters are supplied with the Water System 1already installed.

Ensure the hydroleca sacks are in the correctposition. They will move during transportation.Check that all the plastic pipe connections areproperly fitted. The planter is ready for drainagematerial, filling and planting.

hydroleca sacks

50m

m Ø

fill

er

pip

e

Polythene liner with filler pipe

Hydroleca sacks laid out in base of planter

Ref: 21/A

BOURNEMOUTH planter

ADJUSTABLE FEET




General details

The M30 adjustable foot with swivel base, is screwed into adjustablefoot mounting plate.The mild steel mounting plate with adjustable foot housing, is fixed tothe underside of the planter base.A M30 hex full nut is welded to the underside of the mounting plate.The adjustable foot is adjusted with a 26mm wrench.

M30 adjustable foot withswivel base.The base diameter is122mm.

The swivel base canadjust to allow forsloping ground with afall of up to 1 in 2.06(26°).

For extra security, it ispossible to drill and boltthrough the base of theadjustable feet.

As an extra cost option, Street Design planterscan be supplied with adjustable feet. They allowthe planter to be levelled, before filling andplanting.Adjustable feet are particularly useful if theplanters are likely to be relocated to a newposition.The adjustable foot screw fits into a hex nut,located on the underside of the planter base.

Specification

Adjustable Foot Mounting Plate

Adjustable Foot

Fitting and adjustment

M30 hex full nut

base bearer

adjustable foot housing

Swivel base

Bolt down base

Base diameter

Ref: 22/A

The adjustable foot comprises of a M30 Øthreaded bar, with spherical end section, pressfitted into a black reinforced polyamide base.The swivel base can tilt through

The threaded bar is BZP (bright zinc plated)treated.

360º toaccommodate sloping ground levels.

BOURNEMOUTH planter

LED LIGHTING




Bournemouth planters can be manufactured andsupplied to include plinth, side and top lighting, allspecified to illuminate the planter or thesurrounding paving.Plant, up lighting and down lighting can be usedto create a dramatic planting scheme byintroducing colours or feature spot lighting.We have created seven types of basic lighting toenhance your scheme and the planting. Theseven types of lighting are shown below. Thelighting types can be specified individually or theycan be grouped together to create a range oflighting effects.In its basic form, the lighting is available as coolwhite, warm white, blue, green or red LED units.More complex lighting can be supplied, includingtwilight switches, PIR sensors, timers, infrared,ultraviolet and royal blue emitters, PWMdimmers, RGB, UPS, DMX and remote controlunits.

Side lighting - holes aremanufactured into the sidewalls of the planter to allowthe LED lighting to create adecorative feature to the sidesof the planter

Plinth lighting - LED lighting is fitted to the inside of the planter,located under the base floor, offering a pool of light around thebottom of the planter.

Street Design is pleased to announce newdesigns of wood and metal planters featuringintegrated lighting as standard. These designsmake full use of safe, eco-friendly, low-power,low-voltage, high-efficiency LED lighting with abroad choice of placements, brightness andcolours.Our LED lighting units can handle all of the tasksformerly undertaken by tungsten, halide andfluorescent lamps, and out-perform them in everydepartment. They are extremely flexible - we cansupply almost any configuration of lighting to aclient's specification using our standard lightingunits in these purpose-designed planters.The lighting units can be powered by either a lowvoltage DC supply or mains electricity. The choiceof light levels and power units is also broad. Ourstandard power supply pumps out 12 Volts at 4Amps, in LED terms enough for a very brightplanter. The entire range is from 1 Watt to 1,000Watts.This page outlines the different types of lightingavailable and shows examples of the uses towhich the lighting units can be put.

Overview

Plant lighting - LED lights aresupplied to illuminate andmake features of the planting

Plinth lighting is available in warmand cool white, standard LEDcolours, and RGB strips that allowalmost any colour to be mixed.Plinth lighting can also bespecified for one or more sides(or arcs) of a planter and at anypower level between 1 Watt permetre and 40 Watts per metre.Our standard plinth light is warmwhite and operates at 6 Watts permetre and provides a noticeablelight up to one metre from theedge of the planter (though thisdepends on ambient lightinglevels and the reflectivity of theground surface).

Plinth lighting

Side lighting

Side lighting is offered as feature,decorative lighting from cut-outsin the horizontal timber slats. Lowpowered LED ribbons provide apoint of interest on these planters.These lamps are very noticeableeven under extremely brightconditions, and are quite dazzlingat night.

Plant lighting

The plant lighting array ispositioned down at planting level.Four LED lighting battens arefixed to the inside edges at thetop of the planter. The lights areangled up and illuminate theunderside of the flora, a strikingand unusual effect. Fortunately,the plants don't seem to mind.

Spotlights fitted within the plantercan be angled up to illuminatelarge plants, bushes and treesseveral metres above the plantersurface. LED emitters rated at 1,3 or 5 Watts are equipped with 5,15, 25 or 45 degree collimatinglenses to send a narrow beam ofwhite or coloured light toilluminate the chosen feature highabove the planter. The layout ofthe planting can conceal the lightsources to enhance the effect.

Down Lighting in this context isabout mounting a lamp with alens and reflector above theplanting area to provide top-downillumination. The reflectors comein different shapes and sizes tomatch the light distribution to theshape of the planter. Theproximity of the light source andthe use of an opaque reflectorminimises both the powerrequirements and the unwanted,upward, light pollution.

Up Lighting

Down Lighting

Up lighting - LED up lighting isfitted to the inside top of theplanter, creating a rim of lightbetween the planting and theplanter

Down lighting - An LED light ispole mounted in the centre ofthe planter, illuminating thecomplete planter top andplanting. Depending on theheight, the surroundingground can be illuminated ifrequired.

Ref: 23/A

MATERIAL FINISHES

Standard finishes

BOURNEMOUTH planter

Mild steel planter walls - standard finish

As standard, the pre-galvanised, mildsteel planter wall panels, will be suppliedwith a polyester powder coated finish.As standard the powder colour will beRAL 9005, black. Other RAL colours areavailable on request.

RAL 9006 - white metallic (silver), semi-gloss,polyester powder coating.

The Bournemouth, mild steel, internal planterbase frame are supplied with a black hammeritepainted finish. (Base shown here is for a planterwith optional adjustable feet).

Large Bournemouth tree planters, 1000mm high, withstainless steel top capping

Mild steel base - standard finish

As standard, after fully welding, theinternal mild steel base frame, will bepainted with a black, smooth hammeritepaint.

The Bournemouth planter, comprises of a powdercoated mild steel planter body on a galvanisedsteel frame, with stainless steel top capping.

As standard the stainless steel top capping willbe supplied as grade 304 stainless steel with adull polished finish.Grade 316 stainless steel is also available onrequest.

Grade 304 stainless steel top capping with adull polished finish.

Stainless steel top - standard finish




Ref: 30/A

RAL 9003 - white semi-gloss, polyesterpowder coating.

RAL 9005 - black semi-gloss, polyesterpowder coating.

Optional planter accessories continued

Mild steel planter body

Top capping

Curved internal wall frames

Base frame

Base frame legs

Leg baseplate

Internal wall lining

Base floor

Internal lining

2mm thick pre-galvanised mild steel sheet.

130mm wide x 8mm thick grade 304 stainlesssteel.

70mm wide FSC treated softwood framesfabricated to support outer mild steel wallcladding.

75x50x3mm mild steel RHS.130x5mm mild steel flat.

48.3mm Ø x 3mm mild steel CHS.

88.9mm Ø x 5mm circular disc.

4mm thick Marine grade plywood.

18mm FSC Eucalyptus treated plywood.

Geotextile filter fabric membrane.

General specification

Construction

Assembly

Timber policy

Materials

Finishes

All Street Design products are designed and manufactured using only quality,durable materials, construction details and fixings, to provide a long-lasting,durable life expectancy.

Bournemouth planters will be delivered to site fully assembled for off loading andpositioning on site.

All treated softwood products are manufactured using materials obtained fromgrowers who operate under the Forest Stewardship Council (FSC).All iroko hardwood products are manufactured using materials obtained fromgrowers who operate under the Forest Stewardship Council (FSC).

Hardwood products are constructed using FSC iroko hardwood, from sustainablesources. Softwood products are constructed using FSC European redwood thathas been Wolmanit CX treated, for a desired service life of 30 years minimum.All mild steel fabricated components will be hot dip galvanised after fabrication toBS EN ISO 1461:2009.All stainless steel fabricated components will be grade 304. Grade 316 can bespecified if the location or project requires it.All mild steel fixings will be bright zinc plated, and all stainless steel fixings will beA2 (grade 304). A4 (grade 316) can be specified if the location or project requiresit.Planters will be fitted with a geotextile filter fabric lining, which allows the water todrain through the planter, while retaining the fill material.

The pre-galvanised mild steel walling panels will be supplied with a polyesterpowder finish. The standard colour will be RAL 9005, black. Other coloursavailable on request.The grade 304 stainless steel top capping will be supplied with a dull polishedfinish.The FSC treated softwood and iroko hardwood bench slats will be left natural toreduce the need for re-staining and help reduce maintenance costs. If required,timber bench slats can be supplied with a stained finish using 3 coats of quickdrying water based wood stain, to the colour of your choice.The mild steel bench brackets will be left with a galvanised finish only. If required,after hot dip galvanising, the mild steel components can be polyester powdercoated, to the colour of your choice. The galvanised parts are prepped, treatedand sprayed with the polyester powder, before being baked in an oven.Optional stainless steel planter benches will have a dull polished finish.

Guarantee

All planters are guaranteed for 15 yearsminimum. This guarantee is a minimum and isdependant on the product not being misused orabused. All the materials, treatments andconstruction will allow for a life expectancyconsiderably longer than this.

Product prices

See separate price list for the product prices ofstandard sizes, materials and finishes.

MATERIAL SPECIFICATION

Standard planter

Optional planter accessories

Adjustable feet

Tree anchors

Watering system

Planter benches

Base skirting

M30 adjustable feet with swivel base. SeeAdjustable Foot page for full details.

25x5mm mild steel flat, hot dip galvanised.

Choose either the Street Design reservoir systemor the Mona tank system. See Watering Systempage for full details.

Bournemouth planters can be supplied withintegral planter benches in a variety of materials.The bench slats can be supplied in FSC treatedEuropean redwood or iroko hardwood. The slatswill be bolted to either hot dip galvanised mildsteel or stainless steel bench brackets.

6mm thick mild steel flat, hot dip galvanised withoptional polyester powder coated finish.

Moveable planters

Pergola structures

Trellis panels

LED lighting

Material samples

Bournemouth planters can be manufactured withan internal mild steel frame allowing them to bemoved when planted.

Pergola structures can be manufactured as anintegral part of the planter construction. The steeluprights can be added to carry the upperhorizontal 145x45mm section timber bearers andcross bearers.

Trellis panels can be manufactured as an integralpart of the planter construction. Steel uprightscan be added to carry the horizontal and verticaltrellis timber slats.

The lighting is available as cool white, warmwhite, blue, green or red LED units. Morecomplex lighting can be supplied, includingtwilight switches, PIR sensors, timers, infrared,ultraviolet and royal blue emitters, PWMdimmers, RGB, UPS, DMX and remote controlunits. See Bournemouth LED Lighting page formore details.

Material samples are available on request.

BOURNEMOUTH planterStreet Design LimitedUnit 47Hayhill Industrial EstateBarrow upon SoarLeicestershire LE12 8LD



Ref: 40/A

CARE & MAINTENANCE

Maintaining the standard mild steel finish (steel frame and legs)

Maintaining the standard mild steel finish (planter body panels)

Dirt can be washed off with warm water and a mild detergent. Always use cleanwater and cleaning cloths to avoid surface contamination. If required the mildsteel base frame and planter feet can be re-painted. Brush apply a single coaton top of the existing paint using black, smooth finish hammerite paint.

Polyester powder coated finishes should be washed down with clean warmwater and a mild detergent. Minor touching up can be done with an aerosol tomatch the original powder coated colour. Details can be obtained from StreetDesign Limited. More severe damage can be repaired by sanding down, bymanual or mechanical means, beyond the damaged area, sufficiently far as toensure that any step in the powder coated finish is removed. This will ensurethat after re-finishing the repair will be difficult to detect.

General

All Bournemouth planter products are manufactured using quality materials and finishes.The internal base frames will be fully welded mild steel and will be hammerite painted after fabrication.The galvanised mild steel planter body panels will be supplied with a polyester powder coated finish.

All products requirea varied amount of maintenance, depending on the environment, usage and weather conditions.Galvanised steel will only require cleaning. In time, the powder coated mild steel planter body panelswill require re-coating. The stainless steel top capping will only required cleaning.

The stainless steel top capping will be supplied with a dull polished (brushed) finish.

BOURNEMOUTH planterStreet Design LimitedUnit 47Hayhill Industrial EstateBarrow upon SoarLeicestershire LE12 8LD



Ref: 50/A

Maintaining the standard stainless steel finish (top capping)

Dull polished (brushed) stainless steel should be washed down with clean,warm water with a mild detergent. More severe marks can be removed by usinga fine abrasive, such as a Scotchbrite or stainless steel scouring pad. As dullpolishing is a process of applying fine linear scratches evenly over the surface,it is extremely important that rubbing down with a abrasive pad is done carefullyin a straight line parallel to the existing grained finish. Rust marks or stains areusually caused by environmental contamination from dissimilar materials laidagainst, or near to, the stainless steel. These stains can be removed asdescribed above.

street designcms.esi.info/media/documents/66566_1423822150331.pdf · web site: 01509 815335 01509...

Documents