strail road marking-s installation instructions 02

8/9/2019 STRAIL Road Marking-S Installation Instructions 02

http://slidepdf.com/reader/full/strail-road-marking-s-installation-instructions-02 1/5

STRAIL® road marking-SApplication instructionsSubject to technical modifications / November 2013 / TNA-WMO

STRAIL® level crossing systems / STRAILastic track damping systems

KRAIBURG STRAIL® GmbH & Co. KG • D-84529 Tittmoning • Goellstrasse 8

Phone + 49(0)8683/701-0 • Fax -126 • [email protected] • www.strail.com • www.strailastic.com

www.strail.com / www.strailastic.com



Installation instructions STRAIL® road marking-S ¬ page 2/5 November 2013 / Subject to technical modifications

STRAIL® level crossing systems / D-84529 Tittmoning • Phone +49(0)8683/701-0 • Fax -126 • [email protected] • www.strail.com

# 1 / REQUIREMENTS FOR USE

¬ ambient temperature > min. + 5° C

¬ surface > no residual moisture!

> clean swept

> free from oil and grease

Do not use STRAIL® Road marking-S in closed rooms or without suffi cient ventilation!

# 2 / OPERATING MATERIALS

¬ STRAIL®

Road marking-S / in 400 ml cans1 packaging unit (VPE) =^ 6 cans

¬ STRAIL® Primer / in 0.5 l bottles

¬ Glass beads (OPTIONAL)

# 3 / TOOLS

Paint roller

(frame and roller)

Chalk line

(Chalk line and paint)

Template (available in

different sizes)

optional STRAIL®

marking stick

Personal protective equipment (protective glasses, protective clothing and gloves)

Material for cleaning of the panel surface (broom, leaf blower, spatula)





# 4 / PREPARATION

¬ Begin by cleaning the surface of the rubber plates

with a broom, a leaf blower or a similar tool.

The Road marking may only be applied on dry

surfaces! No residual moisture!

¬ Use the chalk line to mark the lines (areas).

Colour: red

¬ Applying the STRAIL® - Primer:

Apply the STRAIL® - Primer with a hand roller

corresponding to the marked lines, so that the

entire surface is wet.

The paint must be sprayed on within a maximum

of 5 minutes after applying the STRAIL® - Primer.

¬ Position the template corresponding to the lines you

marked before.

# 5 / APPLYING THE ROAD MARKING WITH A SPRAYCAN





¬ Preparing the road marking

Remove the red press button from the can end and

attach it to the designated dowel pin on the

underside of the can.

Press the red button down as far as it will go and

hold the position. Afterwards, shake the can strongly

for approx. 1 minute so that all the components

contained blend well.

¬ Apply the paint evenly and opaquely using the spray

can (distance: approx. 20 cm).

The can has an overhead outlet and it must be used

that way.

Optional > for better handling you can include our

marking stick in your order. The spray

can is put into it and is activated by the

mechanism at the handle.

The template can be removed immediately after the

completion of the spraying process.

# 7 / OPTIONAL > GLASS BEADS

Optional glass beads can be sprinkled into the freshly-applied

paint to achieve good night visibility (reflection effect).





# 8 / CLEANING

Clean all the tools thoroughly after use (marking stick, template).

# 9 / PLEASE NOTE

¬ Surface skinning: after approx. 2 hours

¬ Trafficability: after approx. 3-4 hours

¬ Thoroughly dry: after approx. 8 hours

All consumables are perishable after the package had been opened!

Open cans should be used up immediately if possible!

Store the cans in dry condition and protected from frost!

Material safety data sheets are sent out upon request.

PLEASE NOTE

Please read the installation instructions carefully and use STRAIL® road marking-S in compliance with

our manufacturer’s guidelines or request our assistance. We can only provide a guarantee/warranty if the

installation has been carried out in accordance with our stipulations.

This data sheet is only valid in its latest version and is not updated automatically.

strail road marking-s installation instructions 02

Documents