storwize v7000: quick installation guide - mojo systems...ibm storwize v7000 file module and the ibm...

IBM Storwize V7000

Quick Installation Guide

GC27-2290-04

��

NoteBefore using this information and the product it supports, read the general information in “Notices” on page 35, theinformation in the “Safety and environmental notices” on page ix, as well as the information in the IBM EnvironmentalNotices and User Guide , which is provided on a DVD.

This edition applies to IBM Storwize V7000, Version 6.4.0, and to all subsequent releases and modifications untilotherwise indicated in new editions.

© Copyright IBM Corporation 2010, 2012.US Government Users Restricted Rights – Use, duplication or disclosure restricted by GSA ADP Schedule Contractwith IBM Corp.

Contents

Figures . . . . . . . . . . . . . . . v

Tables . . . . . . . . . . . . . . . vii

Safety and environmental notices . . . ix

Chapter 1. Before you begin theinstallation . . . . . . . . . . . . . 1Step 1. Reviewing your packing slip . . . . . . 4Step 2. Identifying the hardware components . . . 5Step 3. Verifying environmental requirements . . . 9Step 4. Reviewing enclosure location guidelines . . 10

Chapter 2. Performing the hardwareinstallation . . . . . . . . . . . . . 13Step 5. Installing the support rails . . . . . . . 13Step 6. Installing the enclosures. . . . . . . . 15Step 7. Connecting the SAS cables to the expansionenclosures . . . . . . . . . . . . . . . 16Step 8. Attaching the Ethernet cables . . . . . . 20Step 9. Attaching the Fibre Channel longwave SFPtransceivers . . . . . . . . . . . . . . 20Step 10. Attaching the Fibre Channel cables. . . . 21Step 11. Attaching the 10 Gbps Ethernet cables . . 22Step 12. Connecting the power cords . . . . . . 22Step 13. Powering on the system . . . . . . . 24

Chapter 3. Configuring the system. . . 29Setting up your system for the first time with acontrol enclosure or a control enclosure and one ormore expansion enclosures . . . . . . . . . 29

Adding an expansion enclosure into an existingsystem . . . . . . . . . . . . . . . . 31Adding another control enclosure into an existingsystem . . . . . . . . . . . . . . . . 32

Notices . . . . . . . . . . . . . . 35Trademarks . . . . . . . . . . . . . . 37Electronic emission notices . . . . . . . . . 37

Federal Communications Commission (FCC)statement . . . . . . . . . . . . . . 37Industry Canada compliance statement . . . . 38Avis de conformité à la réglementationd'Industrie Canada . . . . . . . . . . . 38Australia and New Zealand Class A Statement 38European Union Electromagnetic CompatibilityDirective . . . . . . . . . . . . . . 38Germany Electromagnetic compatibility directive 39Japan VCCI Council Class A statement . . . . 40People's Republic of China Class A ElectronicEmission Statement . . . . . . . . . . . 40International Electrotechnical Commission (IEC)statement . . . . . . . . . . . . . . 40United Kingdom telecommunicationsrequirements . . . . . . . . . . . . . 40Korean Communications Commission (KCC)Class A Statement . . . . . . . . . . . 40Russia Electromagnetic Interference (EMI) ClassA Statement . . . . . . . . . . . . . 41Taiwan Class A compliance statement . . . . 41

European Contact Information . . . . . . . . 41Taiwan Contact Information . . . . . . . . . 41

© Copyright IBM Corp. 2010, 2012 iii

iv Storwize V7000: Quick Installation Guide

Figures

1. 24 drives and two end caps . . . . . . . 52. 12 drives and two end caps . . . . . . . 53. Rear view of a model 2076-112 or a model

2076-124 control enclosure . . . . . . . . 64. Data ports and LEDs in the rear of the control

enclosure. . . . . . . . . . . . . . 75. 10 Gbps Ethernet ports on the rear of the

Storwize V7000 enclosure . . . . . . . . 86. Rear view of a model 2076-212 or a model

2076-224 expansion enclosure . . . . . . . 87. SAS ports and LEDs in rear of expansion

enclosure. . . . . . . . . . . . . . 98. Hole locations in the front of the rack . . . . 139. Hole locations in the back of the rack . . . . 14

10. Removing the enclosure end cap . . . . . 1511. Securing an enclosure to a rack cabinet 1612. Attaching an expansion enclosure to the

control enclosure . . . . . . . . . . . 1713. Adding a second expansion enclosure. . . . 1814. Attaching SAS cables to the enclosures 1915. Unlocking the cable retention bracket . . . . 2316. Sliding the cable retention bracket directly

behind the power cord . . . . . . . . . 2417. LEDs on the power supply units of the

expansion enclosure. . . . . . . . . . 2518. LEDs on the power supply units of the control

enclosure . . . . . . . . . . . . . 2619. Initialization tool welcome panel . . . . . 30

© Copyright IBM Corp. 2010, 2012 v

vi Storwize V7000: Quick Installation Guide

Tables

1. Steps for the different scenarios . . . . . . 22. Cabling guide. . . . . . . . . . . . 173. LED status when expansion enclosures are

powered on . . . . . . . . . . . . 25

4. LED status when control enclosure is poweredon. . . . . . . . . . . . . . . . 26

© Copyright IBM Corp. 2010, 2012 vii

viii Storwize V7000: Quick Installation Guide

Safety and environmental notices

Review the multilingual safety notices for the IBM® Storwize® V7000 system beforeyou install and use the product.

Suitability for telecommunication environment: This product is not intended toconnect directly or indirectly by any means whatsoever to interfaces of publictelecommunications networks.

To find the translated text for a caution or danger notice:1. Look for the identification number at the end of each caution notice or each

danger notice. In the following examples, the numbers (C001) and (D002) arethe identification numbers.CAUTION:A caution notice indicates the presence of a hazard that has the potential ofcausing moderate or minor personal injury. (C001)

DANGER

A danger notice indicates the presence of a hazard that has the potentialof causing death or serious personal injury. (D002)

2. Locate IBM Storwize V7000 Safety Notices with the user publications that wereprovided with the Storwize V7000 hardware.

3. Find the matching identification number in the IBM Storwize V7000 SafetyNotices. Then review the topics concerning the safety notices to ensure that youare in compliance.

4. Optionally, read the multilingual safety instructions on the Storwize V7000website. Go to the and click the documentation link.

© Copyright IBM Corp. 2010, 2012 ix

x Storwize V7000: Quick Installation Guide

Chapter 1. Before you begin the installation

The Quick Installation Guide contains a set of instructions to help you unpack andinstall your system. The guide is divided into three chapters. The steps in the firstchapter involve verifying your order, becoming familiar with the hardwarecomponent terminology, and ensuring that you have met the environmentalrequirements. The steps in the second chapter involve installing the hardware andattaching the data cables and power cords. The final chapter helps you create yourconfiguration file and access the management GUI. The management GUI guidesyou through the initial configuration process.

If you are installing a new IBM Storwize V7000 Unified system, which includes theIBM Storwize V7000 file module and the IBM Storwize V7000 storage system,follow the installation instructions in the IBM Storwize V7000 Unified QuickInstallation Guide to install the hardware for both machine types 2073 and 2076. TheIBM Storwize V7000 Unified Quick Installation Guide is shipped with the StorwizeV7000 file module hardware. You should use these instructions to add a new IBMStorwize V7000 expansion enclosure to an existing IBM Storwize V7000 Unifiedsystem.

See the following website for the available translated versions of the QuickInstallation Guide:

www.ibm.com/storage/support/storwize/v7000

Occasionally you are referred to topics in the Storwize V7000 Information Center.A copy of the Storwize V7000 Information Center is on the CD that is included inyour shipping order.

Important information:1. The guide assumes that you have read the planning information regarding your

physical environment that is available from the Storwize V7000 InformationCenter.

2. Ensure that you have available any cables that you are supplying.v Setting up a new system that consists of installing a control enclosure only. In

this case, you are not installing any expansion enclosures.v Setting up a new system that consists of installing a control enclosure and

installing one or more expansion enclosures.v Adding an expansion enclosure to an existing system. In this case, you initially

installed a control enclosure or installed a control enclosure and one or moreexpansion enclosures. You want to add an expansion enclosure to your existingsystem. If you are adding an expansion enclosure to an existing system, you donot need to power off the system. You can add an expansion enclosure while thesystem is operational.

v Adding another control enclosure either by itself or with one or more expansionenclosures to an existing system. If you are adding another control enclosure toan existing system, you do not need to power off the system. You can addanother control enclosure while the system is operational.

Note: Support for multiple control enclosures in a single system requires asoftware level of 6.2.0 or later. You must upgrade to the most current level ofsoftware after installing the Storwize V7000. The management GUI can be used

© Copyright IBM Corp. 2010, 2012 1

http://www.ibm.com/storage/support/storwize/v7000

to apply software updates. Refer to the IBM Storwize V7000 support website forthe latest information on software upgrades.

v Setting up a new system that consists of more than one control enclosure. Youinstall the first control enclosure and then the required expansion enclosures. Forother control enclosures, do the setup as if you were adding it to an existingsystem.

Table 1 identifies the order of the steps that you take for each of the differentscenarios.

Table 1. Steps for the different scenarios

New system withcontrol enclosureonly

New system thatincludes a controlenclosure and one ormore expansionenclosures

Adding expansionenclosures to anexisting system

Adding controlenclosures andexpansion enclosuresto an existing system

“Step 1. Reviewingyour packing slip” onpage 4




“Step 2. Identifyingthe hardwarecomponents” on page5

“Step 2. Identifyingthe hardwarecomponents” on page5

“Step 3. Verifyingenvironmentalrequirements” onpage 9




“Step 4. Reviewingenclosure locationguidelines” on page10




“Step 5. Installing thesupport rails” onpage 132




“Step 6. Installing theenclosures” on page152




“Step 7. Connectingthe SAS cables to theexpansionenclosures” on page162


“Step 8. Attachingthe Ethernet cables”on page 20


“Step 12. Connectingthe power cords” onpage 222


Optional: “Step 9.Attaching the FibreChannel longwaveSFP transceivers” onpage 20


“Step 13. Poweringon the system” onpage 242

“Adding anothercontrol enclosure intoan existing system”on page 32

“Step 10. Attachingthe Fibre Channelcables” on page 21

“Step 9. Attachingthe Fibre Channellongwave SFPtransceivers” on page201

“Adding anexpansion enclosureinto an existingsystem” on page 31

Optional: “Step 9.Attaching the FibreChannel longwaveSFP transceivers” onpage 201

2 Storwize V7000: Quick Installation Guide

Table 1. Steps for the different scenarios (continued)

New system withcontrol enclosureonly

New system thatincludes a controlenclosure and one ormore expansionenclosures

Adding expansionenclosures to anexisting system

Adding controlenclosures andexpansion enclosuresto an existing system

“Step 11. Attachingthe 10 Gbps Ethernetcables” on page 22







“Setting up yoursystem for the firsttime with a controlenclosure or a controlenclosure and one ormore expansionenclosures” on page29


“Setting up yoursystem for the firsttime with a controlenclosure or a controlenclosure and one ormore expansionenclosures” on page29


1 These steps are performed for each control enclosure and expansion enclosure thatyou add.2 These steps are performed for each expansion enclosure that you add.

Be familiar with the following informationv Where it is applicable, a CAUTION notice indicates situations that can be

potentially hazardous to you. Before doing a step that contains a caution notice,read and understand the statement that accompanies it.

v Sliding drawers: Do not pull out or install any drawer or feature if the rackstabilizer brackets are not attached to the rack. Do not pull out more than onedrawer at a time. The rack might become unstable if you pull out more than onedrawer at a time.

v Fixed drawers: Any fixed drawer (like the V7000) must not be removed forservicing unless specified by the manufacturer. Attempting to move the drawerpartially or completely out of the rack might cause the rack to become unstableor cause the drawer to fall out of the rack.

v Use safe practices when lifting. The fully populated enclosure weighs about 57.2lbs (26 kg). At least two people are required to lift and install the enclosure intothe rack or to remove an enclosure from the rack.

Chapter 1. Before you begin the installation 3

v Do not use rack-mounted devices as a shelf or workspace. Do not place anyobject on top of rack-mounted devices.

Tools needed

A screwdriver is the only tool needed for the system installation. The screwdrivercan be either a flat-blade screwdriver or a cross head screwdriver.

Step 1. Reviewing your packing slip

After you open your box or boxes, locate your packing slip. Ensure that the itemsthat are listed in your packing slip match what is in the box. Ensure that anyoptional items that you ordered are included in the list. Your shipment mightcontain additional items depending on the order.

Standard ship group contents:

__ v Control enclosure (models 2076-112, 2076-124, 2076-312, or 2076-324 ) orexpansion enclosure (models 2076-212 or 2076-224). The last two digits of themodel number identify the number of drive slots, either 12 or 24.

__ v Rack-mounting hardware kit, including:__ – Two rails (right and left assembly)__ – Two M5 x 15 Hex Phillips screws per rail (two rails)__ – Two M5 x 15 Hex Phillips screws per chassis

Note: Two parts of the rail kit are attached to each side of the enclosure.__ v Two power cords__ v Drive assemblies or blank carriers (installed in the enclosure).

Verify the number of drives and the size of the drives.

Other shipped items:

__ v Environmental Notices flyer__ v Limited Warranty information__ v Software CD that contains the environmental notices, the publication PDFs,

and the information center content. One CD is shipped per enclosure.__ v License Function authorization document__ v IBM Storwize V7000 Quick Installation Guide, GC27-2290


Additional components for control enclosure:

__ v Fibre Channel cables, if ordered__ v Small form-factor pluggable (SFP) transceivers that are preinstalled in the

enclosure__ v Longwave SFP transceivers, if ordered

Additional components for expansion enclosures:

__ v Two SAS cables for each expansion enclosure

Step 2. Identifying the hardware components

The following graphics and descriptions identify the various hardware componentsand port locations for the control enclosure and the expansion enclosure. Eachenclosure takes up the full 2U height in the rack.

See the IBM Storwize V7000 Troubleshooting, Recovery, and Maintenance Guide PDF onthe CD for the full descriptions of the hardware components.

Each enclosure has drives that are located on the front. Figure 1 and Figure 2 showthe front of an enclosure that has space for up to 12 or 24 drives �2�, dependingon the model, and a left end cap �1� and a right end cap �3�.

Control enclosure components

Figure 3 on page 6 shows the rear view of a control enclosure and identifies thelocation of the power supply units and the canisters.

svc00693

1 2 2 3

Figure 1. 24 drives and two end caps

svc00694

1 2 3

Figure 2. 12 drives and two end caps


v Power supply units are located on the left and right of the canisters. Each unitcontains a battery. Power supply �1� is located on the left. Power supply �2� islocated on the right. Power supply �1� is inserted top side up, and powersupply �2� is inverted, or top side down.

Important: The power supply units for the control enclosure and expansionenclosure are not interchangeable.

v Two canisters are housed in the middle of the enclosure. Each canister is knownas an expansion canister. The upper canister, as shown in Figure 3, is canister�3�, and the lower canister is canister �4�. Canister �3� is top side up, andcanister �4� is inverted, or top side down.

Figure 4 on page 7 shows the rear view of a model 2076-112 or a model 2076-124control enclosure and identifies the location of the ports.

1 23

svc00662

4

Figure 3. Rear view of a model 2076-112 or a model 2076-124 control enclosure


v �1� Fibre Channel ports. Each canister has four Fibre Channel ports. They are ina block of four in two rows of two connectors. The ports are numbered 1 - 4from left to right, top to bottom. Their use is optional.

v �2� USB ports. Each canister has two USB ports. The ports are side by side onthe canister and are numbered 1 on the left and 2 on the right. One port is usedduring installation.

v �3� Ethernet ports. Each canister has two Ethernet ports. The ports are side byside on the canister. They are numbered 1 on the left and 2 on the right on theupper canister. The port locations are inverted for the lower canister. Port 1 mustbe connected first; the use of port 2 is optional.

v �4� Serial-attached SCSI (SAS) ports. Each canister has two SAS ports. The portsare side by side on the canister. They are numbered 1 on the left and 2 on theright. Port 1 must be connected first if you are adding one expansion enclosure.Port 2 must be connected if you are adding a second expansion enclosure.

Note: The reference to the left and right locations applies to canister 1, which isthe upper canister. The port locations are inverted for canister 2, which is the lowercanister.

Figure 5 on page 8 shows the rear view of a model 2076-312 or a model 2076-324control enclosure with the optional 10 Gbps Ethernet ports installed. All otherports remain the same.

svc00669

1 42 3

14 23

Figure 4. Data ports and LEDs in the rear of the control enclosure


v �1� 10 Gbps Ethernet port 3 which is the left port.v �2� 10 Gbps Ethernet port 4 which is the right port.

Expansion enclosure components

Figure 6 shows the rear view of an expansion enclosure and identifies the locationof the power supply units and the canisters. The ports and their use are describedlater in this section.

v Power supply units are on the left and right of the canisters. Power supply �1�is located on the left. Power supply �2� is located on the right. Power supply 1is inserted top side up, and power supply 2 is inverted, or top side down.

Important: The power supply units for the control enclosure and expansionenclosure are not interchangeable.

v Two canisters are housed in the middle of the enclosure. Each canister is knownas an expansion canister. The upper canister, as shown in Figure 6, is canister�3�, and the lower canister is canister �4�. Canister 3 is top side up, and canister4 is inverted, or top side down.

Figure 7 on page 9 shows the rear view of an expansion enclosure and identifiesthe SAS port locations.

svc00733

12

1 2

Figure 5. 10 Gbps Ethernet ports on the rear of the Storwize V7000 enclosure

1 23

svc00610

4

Figure 6. Rear view of a model 2076-212 or a model 2076-224 expansion enclosure


Each canister has two SAS ports that are numbered 1 on the left �1� and 2 on theright �2�. Port 1 must be connected if you are adding one expansion enclosure.Port 2 must be connected if you are adding a second expansion enclosure.

Note: The reference to the left and right locations applies to canister 1, which isthe upper canister. The port locations are inverted for canister 2, which is the lowercanister.

Miscellaneous hardware

The USB flash drive (also known as a USB flash drive) is packaged with thepublications and contains the initialization tool for performing the initial systemconfiguration.

Step 3. Verifying environmental requirements

Certain requirements for the physical site must be met to ensure that your systemworks reliably. This step includes verifying that adequate space in a suitable rack isavailable and that requirements for power and environmental conditions are met.This documentation assumes that you have completed the physical planning forthe environment of your system.

If you have not done the environmental planning for your system, see the StorwizeV7000 physical installation planning topic in the Storwize V7000 Information Center.

If your system contains more than one control enclosure, you must configure theFibre Channel switch for correct zoning between the control enclosures. See theconfiguring topics in the Storwize V7000 Information Center that containinformation about zoning rules and zoning details.

You must use a supported web browser. Verify that you are using a supported webbrowser from the following website:


svc00668

1

12

2

Figure 7. SAS ports and LEDs in rear of expansion enclosure



1. From the Search support input field, type browser.You are shown a search result for “IBM Storwize V7000 Supported HardwareList, Device Driver, Firmware and Recommended Software Levels.” Click thesearch entry.

2. Scroll down to the Other Hardware and Software section.3. Find and select Management GUI.

Step 4. Reviewing enclosure location guidelines

Follow these guidelines to create a plan that identifies an appropriate location inthe rack for the enclosure or enclosures that you are installing now or in thefuture. An enclosure requires two standard rack units of space in a rack. SeeFigure 9 on page 14 for a sample template of two rack units.

If you are installing a control enclosure only, follow these guidelines:

Position the enclosure in the rack so that you can easily view it and access it forservicing. This action helps the rack to remain stable and provides a way for twoor more people to install and remove the enclosure.

If you are installing a control enclosure plus one or more expansion enclosures,follow these guidelines:

If you have one or more expansion enclosures, position the control enclosure in themiddle of the expansion enclosures. Balance the expansion enclosures above andbelow the control enclosure.

For example, position the control enclosure in the middle of the enclosures for easeof cabling.v You can have no more than five expansion enclosures attached to SAS port 1 of

the control enclosure.v You can have no more than four expansion enclosures attached to SAS port 2 of

the control enclosure.v Position the enclosures together; avoid adding other equipment between

enclosures.v When you add the first expansion enclosure to a control enclosure, it is

preferable to add the enclosure directly below the control enclosure.v When you add a second expansion enclosure, it is preferable to add the

enclosure directly above the control enclosure. For each additional expansionenclosure that you add, alternately add it below or above the control enclosure.

v Position the enclosures in the rack so that you can easily view them and accessthem for servicing. This action helps the rack to remain stable and provides away for two or more people to install and remove the enclosures.

If you are installing an expansion enclosure to an existing system, follow theseguidelines:

When you add the first expansion enclosure to a control enclosure, it is preferableto add the enclosure directly below the control enclosure. When you add a secondexpansion enclosure, it is preferable to add the enclosure directly above the controlenclosure. For each expansion enclosure that you add, alternately add it below orabove the control enclosure.


If you are adding an expansion enclosure to an existing system, you do not need topower off the system. You can add an expansion enclosure while the system isoperational.

If you are installing more than one control enclosure, follow these guidelines:

If you plan to add more than one set of a control enclosure and expansionenclosures, put the second set of enclosures above the first set of enclosures.Review the guidelines for “If you are installing a control enclosure plus one ormore expansion enclosures.” You can also add the second set of enclosures in adifferent rack.

Note: When you perform the installation of the enclosures, load the rack from thebottom to ensure rack stability. Empty the rack from the top down.

If you are adding another control enclosure to an existing system, you do not needto power off the system. You can add the control enclosure while the system isoperational.


Chapter 2. Performing the hardware installation

You have completed the initial steps of verifying the shipping contents andbecoming familiar with the hardware components. You have verified that thepower and environmental requirements are met and have planned the location ofthe enclosures. You are now ready to begin installing the hardware componentsand connecting the data cables and power cords.

Step 5. Installing the support rails

About this task

To install the support rails, perform the following steps:1. Locate the rack mounting rails and screws.

The rail assembly is made up of two sets of rails. One set of rails is alreadyinstalled, or preinstalled, on the sides of the enclosures. The other set of railsmust be installed in the rack cabinet. The rails on the sides of the enclosuresslide into the rails that are installed in the rack cabinet.

2. Working at the front of the rack cabinet, identify the two standard rack unitsof space in the rack into which you want to install the support rails.Figure 8 shows two rack units with the front mounting holes identified.

v �1� Bottom rail location pin holev �2� Enclosure mounting screw hole. Do not insert the screw until the

enclosure is installed.v �3� Rack mounting screw hole

2 Units

1

2

3

4

svc00695

Figure 8. Hole locations in the front of the rack


v �4� Top rail location pin hole3. Align the bottom of the rail with the bottom of the two rack units. Insert the

rail location pins �1� and �4� through the holes in the rack cabinet.4. Insert a clamping screw into the rack mounting hole �3� between the rail

location pins.5. Tighten the screw to secure the rail to the rack.6. Working from the rear of the rack cabinet, extend the rail that you secured to

the front to align the bottom of the rail with the bottom of the two rack units.

Note: Ensure that the rail is level between the front and the back.Figure 9 shows two rack units with the back mounting holes identified.

v �1� Bottom rail location pin holev �2� Rack mounting screw holev �3� Top rail location pin hole

7. Insert the rail location pins through the holes �1� and �3� in the rack cabinet.8. Insert a clamping screw into the rack mounting hole �2� between the rail

location pins.9. Tighten the screw to secure the rail to the rack from the back side.

10. Repeat the steps to secure the opposite rail to the rack cabinet.11. Repeat the procedure for each additional enclosure.

svc00696

2 Units

1

2

3

Figure 9. Hole locations in the back of the rack


Step 6. Installing the enclosures

About this task

CAUTION:

1. To lift and install the enclosure into the rack requires at least two people.

2. Load the rack from the bottom to ensure rack stability. Empty the rack fromthe top down.

Following your enclosure location plan, install the correct type of enclosure startingfrom the bottom.1. On either side of the drive assemblies, remove the enclosure end caps by

squeezing the middle of the cap and pulling it away from the front of theenclosure.

2. Align the enclosure with the front of the rack cabinet.3. Carefully slide the enclosure into the rack along the rails until the enclosure is

fully inserted.

Notes:

a. The preinstalled rails on the sides of the enclosure must fit into therack-mounted rails that you previously installed.

b. The rails are not designed to hold an enclosure that is partially inserted.The enclosure must always be in a fully inserted position.

c. Do not have more than one enclosure extended out of the rack at the sametime to avoid the danger of the rack toppling over.

4. Insert a screw into the hole behind each enclosure end cap and tighten thescrew.

svc00648

Figure 10. Removing the enclosure end cap

Chapter 2. Performing the hardware installation 15

5. After matching each end cap's serial number to the serial number found on therear of each enclosure, push the end caps back into position.

6. Repeat this procedure for each additional enclosure that you install.

Step 7. Connecting the SAS cables to the expansion enclosures

About this task

This task applies if you are installing one or more expansion enclosures.

Note: The enclosure terminology that is used in this topic is described fully in“Step 2. Identifying the hardware components” on page 5.

Be aware of these guidelines when you begin to attach the cables to the SAS ports:v No more than five expansion enclosures can be chained to port 1 (below the

control enclosure). The connecting sequence from port 1 of the node canister iscalled chain 1.

v No more than four expansion enclosures can be chained to port 2 (above thecontrol enclosure). The connecting sequence from port 2 of the node canister iscalled chain 2.

v No cable can be connected between a port on an upper canister and a port on alower canister.

v Attach cables serially between enclosures; do not skip an enclosure.v The last enclosure in a chain must not have cables in port 2 of canister 1 and

port 2 of canister 2.v Ensure that cables are installed in a tidy manner to reduce the risk of cable

damage when Storwize V7000 replaceable units are removed or inserted.v Arrange your cables to provide access to:

– The USB ports. Access is required to this port when you use the USB flashdrive to configure the system.

– The enclosures themselves. Access is required to the hardware for servicingand for safely removing and replacing components using two or more people.

svc00688

Figure 11. Securing an enclosure to a rack cabinet


v Ensure that each SAS cable is fully inserted. A click is heard when the cable issuccessfully inserted.

Note: If you make a mistake during cabling and must unplug a SAS cable, pullthe blue tag to release the cable.

Procedure1. Review Table 2 and the following figures before attaching the SAS cables.

Table 2. Cabling guide.

From: To:

�1� Port 1 of upper canister, controlenclosure

�2� Port 1 of upper canister, expansionenclosure 1

�3� Port 1 of lower canister, controlenclosure

�4� Port 1 of lower canister, expansionenclosure 1

�5� Port 2 of upper canister, controlenclosure


�7� Port 2 of lower canister, controlenclosure






2. Attach the SAS cables from the control enclosure to the first expansionenclosure as shown in Figure 12. Remove the protective end covers, ifnecessary. The first expansion enclosure is below the control enclosure.

a. Port 1 �1� of the upper canister, control enclosure, attaches to Port 1 �2� ofthe upper canister, expansion enclosure 1.

b. Port 1 �3� of the lower canister, control enclosure, attaches to Port 1 �4� ofthe lower canister, expansion enclosure 1. The port locations on the lowercanister are inverted from the port locations on the upper canister. Port 1 onthe lower canister is opposite port 1 on the upper canister.

Control enclosure

Expansion enclosure 1

2

4

svc00661

1

3

Figure 12. Attaching an expansion enclosure to the control enclosure


Note: The connecting sequence from port 1 of the node canister is calledchain 1.

3. Attach the SAS cables from the control enclosure to the second expansionenclosure as shown in Figure 13. The second expansion enclosure is above thecontrol enclosure.

a. Port 2 �5� of the upper canister, control enclosure, attaches to Port 1 �6� ofthe upper canister, expansion enclosure 2.

b. Port 2 �7� of the lower canister, control enclosure, attaches to Port 1 �8� ofthe lower canister, expansion enclosure 2. The port locations on the lowercanister are inverted from the port locations on the upper canister. Port 1 onthe lower canister is opposite port 1 on the upper canister.

Note: The connecting sequence from port 2 of the node canister is calledchain 2.

4. Attach the SAS cables from the first expansion enclosure to the third expansionenclosure.

Control enclosure


2


6

8

4

svc00660

15

37

Figure 13. Adding a second expansion enclosure


a. Port 2 �9� of the upper canister, expansion enclosure 1, attaches to Port 1�10� of the upper canister, expansion enclosure 3.

b. Port 2 �11� of the lower canister, expansion enclosure 1, attaches to Port 1�12� of the lower canister, expansion enclosure 3.

5. Attach SAS cables for additional expansion enclosures. You can add up to nineexpansion enclosures. You add a fourth expansion enclosure at �13� and �14�on expansion enclosure 2.a. Add the enclosures alternately to chain 1, and then chain 2.b. Use port 2 on the canisters that are already connected to attach to port 1 on

the canisters of the enclosures that you want to add.c. Connect the SAS cables from canister 1 to canister 1.d. Connect the SAS cables from canister 2 to canister 2.

6. Verify your cabling.

Control enclosure


2



6

13

8

9

411

10

12

svc00645

1 5

7 3

Figure 14. Attaching SAS cables to the enclosures


Step 8. Attaching the Ethernet cables

About this task

This task applies if you are installing a control enclosure only or a controlenclosure plus one or more expansion enclosures.

This task assumes that your initial planning has determined where the Ethernetcables are to be located.

Attention: The default service IP addresses on your new Storwize V7000 controlenclosures might conflict with existing devices that are attached to the network orwith other new Storwize V7000 control enclosures that you are installing. Theservice IP address 192.168.70.121 subnet mask 255.255.255.0 is preconfigured onEthernet port 1 of the upper canister, canister 1. The service IP address192.168.70.122 subnet mask 255.255.255.0 is preconfigured on Ethernet port 2 of thelower canister, canister 2.

If you encounter this situation, change the service IP addresses on the new nodesbefore connecting the Ethernet cables. For details, see Information required beforeinitializing your system Also refer to the IBM Storwize V7000 Troubleshooting,Recovery, and Maintenance Guide PDF on the DVD for further information aboutsetting service IP addresses, using a USB flash drive.

When you install multiple control enclosures, you increase the chance of conflictsin IP addresses.

To attach the Ethernet cables, perform the following steps:1. For each node canister in the control enclosure, connect an Ethernet cable

between Ethernet port 1 of the canister and an enabled port on your Ethernetswitch or router. Port 1 can be used for management, service, and iSCSI.

Note: Ethernet cables are not supplied as part of your order. A CAT 5unshielded twisted pair (UTP) is the minimum requirement for an Ethernetcable.Ensure that cables are installed in a tidy manner to reduce the risk of cabledamage when Storwize V7000 replaceable units are removed or inserted.

2. Optionally attach Ethernet cables between Ethernet port 2 on each nodecanister and your Ethernet network. Port 2 can be used for management andiSCSI

Step 9. Attaching the Fibre Channel longwave SFP transceivers

About this task

This task applies if you ordered Fibre Channel longwave SFP transceivers.

Attention: The shortwave SFP transceivers are preinstalled in the controlenclosure. No further action is required if you are using the shortwave SFPtransceivers.

To attach the SFP transceivers, perform the following steps:


Procedure1. For both node canisters in the control enclosure, identify which of the four

shortwave SFP transceivers must be replaced with longwave SFP transceivers.2. Remove the shortwave SFP transceivers.3. Plug the longwave SFP transceivers into ports 1-4, as needed.

For more information about removing and replacing hardware components, seethe “Removing and replacing parts” topics in the Storwize V7000 InformationCenter to find out how to perform these procedures.

Step 10. Attaching the Fibre Channel cables

About this task

This task applies if you are installing a control enclosure and are connecting it toyour Fibre Channel network.

This task assumes that your initial planning has determined where the FibreChannel cables are to be located.

To attach the Fibre Channel cables, perform the following steps:

Procedure1. Remove any protective end covers from the cables or the SFP transceivers.2. Attach the Fibre Channel cables to a Fibre Channel switch.

Ensure that cables are installed in a tidy manner to reduce the risk of cabledamage when Storwize V7000 replaceable units are removed or inserted.

3. Attach the other ends of the Fibre Channel cables to the Fibre Channel ports onthe node canisters.

Note: If you use fewer than eight Fibre Channel cables, it does not matterwhich Fibre Channel ports you use. Ensure that you attach the Fibre Channelcables evenly between the two node canisters.

What to do next

After you have started your system, be sure to configure your Fibre Channelzoning to match the guidelines in the “Zoning details” topic in the Storwize V7000Information Center.

Notes:

1. Ensure that Storwize V7000 ports with shortwave SFP transceivers areconnected to shortwave SFP transceivers on the Fibre Channel switch.

2. Ensure that Storwize V7000 ports with longwave SFP transceivers areconnected to longwave SFP transceivers on the Fibre Channel switch.

3. The cable types are different between longwave and shortwave connections.Ensure that the correct cable type is used.


Step 11. Attaching the 10 Gbps Ethernet cables

About this task

This task applies if you are installing a model type 2076-312 or a model type2076-324 that has the 10 Gbps Ethernet ports.

This task assumes that your initial planning has determined where the Ethernetoptical cables are to be located.

To attach the optical cables, perform the following steps:1. Remove any protective end covers from the cables or the SFP transceivers.2. Attach the Ethernet optical cables to ports on a 10 Gbps Ethernet switch.

Ensure that cables are installed in a tidy manner to reduce the risk of cabledamage when Storwize V7000 replaceable units are removed or inserted.

3. Attach the other ends of the Ethernet optical cables to the 10 Gbps Ethernetports on the node canisters.See Figure 5 on page 8 for the port locations.

Important: For each set of canisters, connect the Ethernet ports with the samenumbers to the same subnets so that the failover of system management andiSCSI IP addresses can occur between canisters. For example, canister 1, port 3,must be on the same subnet as canister 2, port 3, and canister 1, port 4, must beon the same subnet as canister 2, port 4.

What to do next

Step 12. Connecting the power cords

About this task

Two power supply units are located in each enclosure. Ensure that the powerswitches for each power supply unit are off.

Note: Each power supply unit comes with an attached cable retention bracket thatfastens around the power cord to prevent the cord from being removedaccidentally.

Perform the following steps when you attach the power cord to each power supplyunit:1. Straighten the cable tie on the cable retention bracket. The cable retention

bracket is attached to the power supply unit.2. Open the cable retention bracket.


3. Slide the cable retention bracket away from the power supply unit until there isenough room to attach the cable retention bracket to the cable. When slidingthe bracket away from the cable plug-in, pull the lever on the bracket thatcontrols the cable tie slightly towards the center of the canister. You do notneed to pull the lever to slide the bracket towards the cable plug-in.

4. Attach a power cord to each of the two power supply units in each enclosure.Ensure that cables are installed in a tidy manner to reduce the risk of cabledamage when Storwize V7000 replaceable units are removed or inserted.

5. Place the cable retention bracket around the end of the cable that plugs into thepower supply unit.

6. Slide the cable retention bracket along the cord until it fits snugly against theplug end of the cable.

svc00686

Figure 15. Unlocking the cable retention bracket


7. Tighten the fastener around the plug.8. Repeat the steps for each additional power cord.9. Plug the power cords into a properly grounded electrical outlet. To provide

power failure redundancy, plug the power cords for the individual powersupply units for each enclosure into separate power distribution units, ifpossible.

Step 13. Powering on the system

About this task

Attention: Do not operate the system when the drive assemblies are missing.Drive assemblies that are missing disrupt the airflow; the drives do not receivesufficient cooling. You must insert blank carriers into unused drive bays.

This topic is divided into two procedures; the first one, powering on an expansionenclosure; the second one, powering on a control enclosure.

Powering on an expansion enclosure:

1. Power on the newly installed enclosures. Use the power switch on each of thetwo power supply units in the back of the expansion enclosure.

2. Use the information in Table 3 on page 25 to verify the state of the lightemitting diodes (LEDs) on the system. Verify that no faults are detected. See theIBM Storwize V7000 Troubleshooting, Recovery, and Maintenance Guide PDF on theCD if problems are encountered.

Figure 17 on page 25 shows the location of the LEDs on the power supply units inthe rear of the expansion enclosure.

svc00644

Figure 16. Sliding the cable retention bracket directly behind the power cord


Table 3. LED status when expansion enclosures are powered on

Hardware component LED name and symbolIf power on and no fault isdetected

Left enclosure end cap, frontof enclosure Power, top

LED is on.

Fault, middleLED is off.

Identify, bottomLED is off.

Expansion canister, rear. Thereference to the top andbottom locations applies tocanister 1, which is the uppercanister. The LED locationsare inverted for canister 2,which is the lower canister.

Canister status, topLED is on.

Fault status, bottomLED is off.

Power supply unit,expansion enclosure. Thereference to the left and rightlocations applies to powersupply unit 1, which is theleft power supply. The LEDlocations are inverted forpower supply unit 2, whichis the right power supply.

Power supply, upper right LED is on.

Fan failureLED is off.

dc power failure LED is off.

ac power failure LED is off.

Powering on a control enclosure:

1

svc00671

1

Figure 17. LEDs on the power supply units of the expansion enclosure


1. Power on the control enclosure, if it is not already powered on and configured.Use the power switch on each of the two power supply units, located in theback of the enclosure.

2. Use Table 4 to verify the state of the LEDs on the system. Verify that no faultsare detected.

Figure 18 shows the location of the LEDs on the power supply units in the rear ofthe control enclosure.

Table 4. LED status when control enclosure is powered on

Hardware component LED nameIf power on and no fault isdetected

Left enclosure end cap, frontof enclosure Power, top

LED is on.

Fault, middleLED is off.

Identify, bottomLED is off.

svc00670

1

1

Figure 18. LEDs on the power supply units of the control enclosure


Table 4. LED status when control enclosure is powered on (continued)

Hardware component LED nameIf power on and no fault isdetected

Node canister, rear. Thereference to the top andbottom locations applies tocanister 1, which is the uppercanister. The LED locationsare inverted for canister 2,which is the lower canister.

Fibre Channel port If the Fibre Channel port isused: One or more LEDs areon or flashing per port. TheLEDs are located betweenthe Fibre Channel ports. Thearrow-shaped LEDs pointtoward the affected port.

Ethernet port, if used One or more LEDs are onper port.

SAS ports When a SAS port isfunctioning correctly, all fourgreen LEDs above the portare on. If no cable is pluggedinto the port, or if thecanister at either end of thecable is not yet fully started,the LEDs are not on.

System status, leftLED is flashing or on. Thestatus is on if the nodecanister is an active memberof a clustered system. TheLED is flashing if the nodecanister is in service orcandidate state. If the LED isoff, the node canister mightstill be booting up. Wait upto 5 minutes for the nodecanister to complete bootingup.

Fault status, middleLED is off.

Power status, rightLED is on.

Power supply unit, controlenclosure. The reference tothe left and right locationsapplies to power supply unit1, which is the left powersupply. The LED locationsare inverted for powersupply unit 2, which is theright power supply.

Power supply, upper right LED is on.

ac power failure LED is off.

dc power failure LED is off.

Fan failureLED is off.

Battery failure+ - LED is off

Battery good, lower right+ -

LED is on or flashing.

Attention: Do not go to the next section until the LEDs are in the required states.

See the IBM Storwize V7000 Troubleshooting, Recovery, and Maintenance Guide PDF onthe CD if problems are encountered.


Chapter 3. Configuring the system

This document helps you set up your system for the first time.

About this task

In the previous steps, you installed the enclosures in the rack, connected all cables,powered the system on, and checked the LED status for the system. When youhave completed all these steps, continue with the last step to configure the system.

The last step for configuring your system provides instructions for severalscenarios:v Setting up your system for the first time.v Adding one or more expansion enclosures to an existing system.v Adding another control enclosure to an existing system.

If you are installing a new IBM Storwize V7000 Unified system, which includes theIBM Storwize V7000 file module and the IBM Storwize V7000 storage system,follow the installation instructions in the IBM Storwize V7000 Unified QuickInstallation Guide to install the hardware for both machine types 2073 and 2076. TheIBM Storwize V7000 Unified Quick Installation Guide is shipped with the StorwizeV7000 file module hardware. You should use these instructions to add a new IBMStorwize V7000 expansion enclosure to an existing IBM Storwize V7000 Unifiedsystem.

Setting up your system for the first time with a control enclosure or acontrol enclosure and one or more expansion enclosures

This document guides you through setting up the control enclosure.

About this task

To complete this step, you must use a supported web browser. Verify that you areusing a supported web browser from the following website:


Note: You must upgrade to the most current level of software after installing theStorwize V7000. The management GUI can be used to apply software updates.Refer to the IBM Storwize V7000 support website for the latest information aboutsoftware upgrades.

You must initialize the system by creating a clustered system and configuring it.The first stage is to create the clustered system using the initialization tool and theUSB flash drive. You must know the required IP management address that isassigned to the system before continuing.

Procedure1. Locate the USB flash drive that was shipped with your order in the

documentation package.



Note: You might encounter a problem where the code cannot be run if you useyour own USB flash drive. The USB flash drive that you use must:v Contain a FAT32 formatted file system on its first partition. NTFS and other

file system types are not supported.v Contain a copy of the Microsoft Windows USB flash drive InitTool.exe

executable that is located in the root directory of the file system.v Be write enabled.

2. Insert the USB flash drive into a USB port in a personal computer that isrunning Microsoft Windows XP Professional or higher.If the system is configured to autorun for USB keys, the initialization tool startsautomatically. Otherwise, open the USB flash drive from My Computer anddouble-click the InitTool.exe.

If you are running a non-Windows operating system, you must create the filesmanually on the USB flash drive. See the IBM Storwize V7000 Troubleshooting,Recovery, and Maintenance Guide PDF on the DVD to learn more about using theUSB flash drive to manage or service the system.

3. Select the Initialize a new Storwize V7000 (block system only) option fromthe Welcome panel of the initialization tool. Click Next. Use the initializationtool to complete the following steps:a. Enter the management IP address. Click Next.b. Transferring the USB flash drive to the powered-on control enclosure to

create the clustered system. Do not insert the USB flash drive until the nodecanister has completed booting up.While the clustered system is being created, the amber fault LED on thenode canister flashes. When the amber fault LED stops flashing, remove theUSB flash drive and reinsert it in your personal computer to restart theinitialization tool. The results of the create clustered system operation areshown. Check that the create operation succeeded.

ifs00004

Figure 19. Initialization tool welcome panel


The system cannot become active until there is sufficient battery power tosafeguard the system in the event of a power failure. If the batteries do nothave sufficient charge, the system cannot start immediately. An estimatedtime for when the system is available is shown. When you receive thebatteries, they normally contain sufficient power for the system to start.The LED status on the node canisters in the control enclosure change whena clustered system starts. The status LED on the node canister that youcreated the clustered system on changes from flashing to fully on when theclustered system is created and there is sufficient battery power tosafeguard the system. After a short wait, the status LED on the other nodecanister changes from flashing to fully on. For information about the LEDs,see “Step 13. Powering on the system” on page 24.If necessary, wait until the system has started.If you are unable to create the clustered system, see the IBM Storwize V7000Troubleshooting, Recovery, and Maintenance Guide PDF on the DVD that isshipped with the system. Remove hardware components only whendirected to do so by the fix procedures. Failure to follow the procedures canresult in loss of access to data or loss of data.

4. If the personal computer from which you are using the initialization tool has asupported browser and an Ethernet connection to the management IP addressthat is assigned to the system, click Launch the management GUI on theresults window. Otherwise, go to a personal computer that has an Ethernetconnection to the management IP address and point a supported browser to themanagement IP address to start the management GUI. You see the managementGUI logon panel.If you are unable to start the management GUI or encounter other problems,see the IBM Storwize V7000 Troubleshooting, Recovery, and Maintenance Guide PDFon the DVD that is shipped with the system.

5. Log in as superuser. Use passw0rd for the password.6. Review the International Program License Agreement (IPLA). You must accept

the agreement before you can continue to use the product.7. The Setup wizard starts and guides you through the initial configuration and

verification of the system. If you are not ready to complete any of theconfiguration steps now, use the configuration tasks in the management GUI tocomplete the configuration at a later time.

8. When you are finished using the USB flash drive, store it in a safe location. Youcan use it to do other tasks.

What to do next

This step completes the quick installation procedures. If you are setting up for thefirst time, see the configuring topics in the Storwize V7000 Information Center andcontinue to follow the tasks available in Getting Started from the managementGUI.

Adding an expansion enclosure into an existing system

About this task



Chapter 3. Configuring the system 31


To add an expansion enclosure into an existing system, perform the followingsteps:

Procedure1. Install the enclosure in the rack.2. Attach the power and SAS cables.3. Power on the enclosure and wait for the SAS LEDs to turn on.4. Start the management GUI.5. Go to Monitoring > System Details.6. Select the system name in the tree.7. Go to Actions > Add Enclosures > Expansion only.8. Continue to follow the on-screen instructions.

What to do next

This step completes the quick installation procedures. Now that you have addedan expansion enclosure into an existing system, continue to perform your standardtasks.

Adding another control enclosure into an existing system

About this task



Note: When you add another control enclosure, you do not use the initializationtool or the USB flash drive.

To add another control enclosure into an existing system, perform the followingsteps:

Procedure1. Configure the Fibre Channel switch to allow for correct zoning between the

control enclosures.The correct zoning provides a way for the Fibre Channel ports to connect toeach other. See the configuring topics in the Storwize V7000 Information Centerthat contain information about zoning rules and zoning details.If the configuration tool for the Fibre Channel switch does not provide detailsof the world wide port names (WWPNs), use the service assistant to find themor use the USB flash drive to find the status of the node. For information aboutthe status of the node, see the IBM Storwize V7000 Troubleshooting, Recovery, andMaintenance Guide PDF on the CD that is shipped with the system.

2. Start the management GUI.3. Go to Monitoring > System Details.4. Select the system name in the tree.5. Go to Actions > Add Enclosures > Control and Expansions.6. Continue to follow the on-screen instructions.



What to do next

This step completes the quick installation procedures. If you are setting up for thefirst time, see the configuring topics in the Storwize V7000 Information Center andcontinue to follow the tasks available in Getting Started from the managementGUI. If you added an expansion enclosure into an existing system, continue toperform your standard tasks.

Chapter 3. Configuring the system 33

Notices

This information was developed for products and services offered in the U.S.A.

IBM may not offer the products, services, or features discussed in this document inother countries. Consult your local IBM representative for information on theproducts and services currently available in your area. Any reference to an IBMproduct, program, or service is not intended to state or imply that only that IBMproduct, program, or service may be used. Any functionally equivalent product,program, or service that does not infringe any IBM intellectual property right maybe used instead. However, it is the user's responsibility to evaluate and verify theoperation of any non-IBM product, program, or service.

IBM may have patents or pending patent applications covering subject matterdescribed in this document. The furnishing of this document does not grant youany license to these patents. You can send license inquiries, in writing, to:

IBM Director of LicensingIBM CorporationNorth Castle DriveArmonk, NY 10504-1785U.S.A.

For license inquiries regarding double-byte character set (DBCS) information,contact the IBM Intellectual Property Department in your country or sendinquiries, in writing, to:

Intellectual Property LicensingLegal and Intellectual Property LawIBM Japan Ltd.1623-14, Shimotsuruma, Yamato-shiKanagawa 242-8502 Japan

The following paragraph does not apply to the United Kingdom or any othercountry where such provisions are inconsistent with local law:INTERNATIONAL BUSINESS MACHINES CORPORATION PROVIDES THISPUBLICATION "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHEREXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIEDWARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY OR FITNESSFOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express orimplied warranties in certain transactions, therefore, this statement may not applyto you.

This information could include technical inaccuracies or typographical errors.Changes are periodically made to the information herein; these changes will beincorporated in new editions of the publication. IBM may make improvementsand/or changes in the product(s) and/or the program(s) described in thispublication at any time without notice.

Any references in this information to non-IBM Web sites are provided forconvenience only and do not in any manner serve as an endorsement of those Websites. The materials at those Web sites are not part of the materials for this IBMproduct and use of those Web sites is at your own risk.


IBM may use or distribute any of the information you supply in any way itbelieves appropriate without incurring any obligation to you.

Licensees of this program who wish to have information about it for the purposeof enabling: (i) the exchange of information between independently createdprograms and other programs (including this one) and (ii) the mutual use of theinformation which has been exchanged, should contact:

IBM CorporationAlmaden Research650 Harry RoadBldg 80, D3-304, Department 277San Jose, CA 95120-6099U.S.A.

Such information may be available, subject to appropriate terms and conditions,including in some cases, payment of a fee.

The licensed program described in this document and all licensed materialavailable for it are provided by IBM under terms of the IBM Customer Agreement,IBM International Program License Agreement or any equivalent agreementbetween us.

Any performance data contained herein was determined in a controlledenvironment. Therefore, the results obtained in other operating environments mayvary significantly. Some measurements may have been made on development-levelsystems and there is no guarantee that these measurements will be the same ongenerally available systems. Furthermore, some measurements may have beenestimated through extrapolation. Actual results may vary. Users of this documentshould verify the applicable data for their specific environment.

Information concerning non-IBM products was obtained from the suppliers ofthose products, their published announcements or other publicly available sources.IBM has not tested those products and cannot confirm the accuracy ofperformance, compatibility or any other claims related to non-IBM products.Questions on the capabilities of non-IBM products should be addressed to thesuppliers of those products.

All statements regarding IBM's future direction or intent are subject to change orwithdrawal without notice, and represent goals and objectives only.

This information is for planning purposes only. The information herein is subject tochange before the products described become available.

This information contains examples of data and reports used in daily businessoperations. To illustrate them as completely as possible, the examples include thenames of individuals, companies, brands, and products. All of these names arefictitious and any similarity to the names and addresses used by an actual businessenterprise is entirely coincidental.

COPYRIGHT LICENSE:

This information contains sample application programs in source language, whichillustrate programming techniques on various operating platforms. You may copy,modify, and distribute these sample programs in any form without payment toIBM, for the purposes of developing, using, marketing or distributing application


programs conforming to the application programming interface for the operatingplatform for which the sample programs are written. These examples have notbeen thoroughly tested under all conditions. IBM, therefore, cannot guarantee orimply reliability, serviceability, or function of these programs. The sampleprograms are provided "AS IS", without warranty of any kind. IBM shall not beliable for any damages arising out of your use of the sample programs.

If you are viewing this information softcopy, the photographs and colorillustrations may not appear.

Trademarks

IBM, the IBM logo, and ibm.com® are trademarks or registered trademarks ofInternational Business Machines Corp., registered in many jurisdictions worldwide.Other product and service names might be trademarks of IBM or other companies.A current list of IBM trademarks is available on the web at Copyright andtrademark information at www.ibm.com/legal/copytrade.shtml.

Adobe and the Adobe logo are either registered trademarks or trademarks ofAdobe Systems Incorporated in the United States, and/or other countries.

Intel, Intel logo, Intel Xeon, and Pentium are trademarks or registered trademarksof Intel Corporation or its subsidiaries in the United States and other countries.

Linux is a registered trademark of Linus Torvalds in the United States, othercountries, or both.

Microsoft, Windows, Windows NT, and the Windows logo are trademarks ofMicrosoft Corporation in the United States, other countries, or both.

UNIX is a registered trademark of The Open Group in the United States and othercountries.

Java and all Java-based trademarks and logos are trademarks or registeredtrademarks of Oracle and/or its affiliates.

Electronic emission noticesThe following electronic emission statements apply to this product. The statementsfor other products that are intended for use with this product are included in theiraccompanying documentation.

Federal Communications Commission (FCC) statementThis explains the Federal Communications Commission's (FCC) statement.

This equipment has been tested and found to comply with the limits for a Class Adigital device, pursuant to Part 15 of the FCC Rules. These limits are designed toprovide reasonable protection against harmful interference when the equipment isoperated in a commercial environment. This equipment generates, uses, and canradiate radio frequency energy and, if not installed and used in accordance withthe instruction manual, might cause harmful interference to radio communications.Operation of this equipment in a residential area is likely to cause harmfulinterference, in which case the user will be required to correct the interference athis own expense.

Notices 37

http://www.ibm.com/legal/copytrade.shtml

Properly shielded and grounded cables and connectors must be used in order tomeet FCC emission limits. IBM is not responsible for any radio or televisioninterference caused by using other than recommended cables and connectors, or byunauthorized changes or modifications to this equipment. Unauthorized changesor modifications could void the user's authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to thefollowing two conditions: (1) this device might not cause harmful interference, and(2) this device must accept any interference received, including interference thatmight cause undesired operation.

Industry Canada compliance statement

This Class A digital apparatus complies with ICES-003.

Cet appareil numérique de la classe A est conform à la norme NMB-003 duCanada.

Avis de conformité à la réglementation d'Industrie CanadaCet appareil numérique de la classe A est conforme à la norme NMB-003 duCanada.

Australia and New Zealand Class A Statement

Attention: This is a Class A product. In a domestic environment this productmight cause radio interference in which case the user might be required to takeadequate measures.

European Union Electromagnetic Compatibility Directive

This product is in conformity with the protection requirements of European Union(EU) Council Directive 2004/108/EC on the approximation of the laws of theMember States relating to electromagnetic compatibility. IBM cannot acceptresponsibility for any failure to satisfy the protection requirements resulting from anon-recommended modification of the product, including the fitting of non-IBMoption cards.

Attention: This is an EN 55022 Class A product. In a domestic environment thisproduct might cause radio interference in which case the user might be required totake adequate measures.

Responsible Manufacturer:

International Business Machines Corp.New Orchard RoadArmonk, New York 10504914-499-1900

European community contact:

IBM Deutschland GmbHTechnical Regulations, Department M372


IBM-Allee 1, 71139 Ehningen, GermanyTele: +49 7032 15 2941e-mail: mailto:[email protected]

Germany Electromagnetic compatibility directive

Deutschsprachiger EU Hinweis: Hinweis für Geräte der Klasse AEU-Richtlinie zur Elektromagnetischen Verträglichkeit

Dieses Produkt entspricht den Schutzanforderungen der EU-Richtlinie2004/108/EG zur Angleichung der Rechtsvorschriften über die elektromagnetischeVerträglichkeit in den EU-Mitgliedsstaaten und hält die Grenzwerte der EN 55022Klasse A ein.

Um dieses sicherzustellen, sind die Geräte wie in den Handbüchern beschrieben zuinstallieren und zu betreiben. Des Weiteren dürfen auch nur von der IBMempfohlene Kabel angeschlossen werden. IBM übernimmt keine Verantwortung fürdie Einhaltung der Schutzanforderungen, wenn das Produkt ohne Zustimmung derIBM verändert bzw. wenn Erweiterungskomponenten von Fremdherstellern ohneEmpfehlung der IBM gesteckt/eingebaut werden.

EN 55022 Klasse A Geräte müssen mit folgendem Warnhinweis versehen werden:

"Warnung: Dieses ist eine Einrichtung der Klasse A. Diese Einrichtung kann imWohnbereich Funk-Störungen verursachen; in diesem Fall kann vom Betreiberverlangt werden, angemessene Mabnahmen zu ergreifen und dafüraufzukommen."

Deutschland: Einhaltung des Gesetzes über dieelektromagnetische Verträglichkeit von Geräten

Dieses Produkt entspricht dem "Gesetz über die elektromagnetische Verträglichkeitvon Geräten (EMVG)." Dies ist die Umsetzung der EU-Richtlinie 2004/108/EG inder Bundesrepublik Deutschland.

Zulassungsbescheinigung laut dem Deutschen Gesetz über dieelektromagnetische Verträglichkeit von Geräten (EMVG) (bzw. derEMC EG Richtlinie 2004/108/EG) für Geräte der Klasse A

Dieses Gerät ist berechtigt, in übereinstimmung mit dem Deutschen EMVG dasEG-Konformitätszeichen - CE - zu führen.

Verantwortlich für die Einhaltung der EMV Vorschriften ist der Hersteller:International Business Machines Corp.New Orchard RoadArmonk,New York 10504Tel: 914-499-1900

Der verantwortliche Ansprechpartner des Herstellers in der EU ist:

IBM Deutschland GmbHTechnical Regulations, Department M372IBM-Allee 1, 71139 Ehningen, GermanyTele: +49 7032 15 2941e-mail: mailto:[email protected]

Notices 39

mailto:[email protected]


Generelle Informationen: Das Gerät erfüllt dieSchutzanforderungen nach EN 55024 und EN 55022 Klasse A.

Japan VCCI Council Class A statement

People's Republic of China Class A Electronic EmissionStatement

International Electrotechnical Commission (IEC) statementThis product has been designed and built to comply with (IEC) Standard 950.

United Kingdom telecommunications requirements

This apparatus is manufactured to the International Safety Standard EN60950 andas such is approved in the U.K. under approval number NS/G/1234/J/100003 forindirect connection to public telecommunications systems in the United Kingdom.

Korean Communications Commission (KCC) Class AStatement


Russia Electromagnetic Interference (EMI) Class A Statement

Taiwan Class A compliance statement

European Contact InformationThis topic contains the product service contact information for Europe.

European Community contact:IBM Technical RegulationsPascalstr. 100, Stuttgart, Germany 70569Tele: 0049 (0)711 785 1176Fax: 0049 (0)711 785 1283Email: mailto: tjahn @ de.ibm.com

Taiwan Contact InformationThis topic contains the product service contact information for Taiwan.IBM Taiwan Product Service Contact Information:IBM Taiwan Corporation3F, No 7, Song Ren Rd., Taipei TaiwanTel: 0800-016-888

rusem

i

f2c0

07

90

Notices 41


��

Part Number: 85Y6159

Printed in USA

GC27-2290-04

(1P)

P/N:

85Y6159

storwize v7000: quick installation guide - mojo systems...ibm storwize v7000 file module and the ibm...

Documents