stem focused classroom & training solutions • 2015 … · stem focused classroom &...

Explore Technology with fischertechnik • Building Blocks of STEM Education. bb

STEM Focused Classroom & Training Solutions • 2015 U.S. Edition

ROBOTICS • PHYSICS • G

REEN ENERGY • ELECTRONICS

STEM LEARNING IS FUN!

PNEUMATICS • OPTICS • A

UTOMATION & SIMULATION

PROGRAMMING • CURRICULUM SOLUTIONS

Explore Technology with fischertechnik • Building Blocks of STEM Education.

Contents: Introduc�on to STEM Series (for elementary school students) 3 Introduc�on to STEM I 4 Introduc�on to STEM II 5 STEM Fundamentals Series (Middle School and up) 6 Mechanics 7 Electronics 8 Op�cs & Lights 9 Physics I 10 Physics II 11 Pneuma�cs 12 Green Energy 13 Drive Systems 14 Advanced STEM: Robo�cs 15 Robto�cs: Beginner 16 Robo�cs: Advanced 17 Robo�cs in Industry 18 Robo�cs and Electropnuema�cs 19 Robo�cs TXT Controller 20 So�ware and Power Op�ons 21 Standards Focused Classroom Solu�ons with Curriculum fischertechnik STEM Lab Program 22-23 Robo�cs Compe��on Lab 24 ROBO TX Explorer 25 Simula�on and Training Models 26-27 STEM History da Vinci Machines 28 Technical Revolu�ons 29 PLUS - Motors, Storage and Accessories 30-31

fischertechnik – building blocks for engaging, hands-on STEM education These days it seems everywhere you turn, leading educators are stressing the importance of STEM (Science, Technology, Engineering and Mathematics) Education, and the reason for this is simple. Demand for scientists and engineers is expected to grow at a rate far exceeding any other occupational field. At the same time fewer and fewer students are pursuing careers in these areas. When they are, they are often not performing at a sufficient level of academic achievement to be successful. While most schools do address the areas of Science and Math to varying degrees, the two aspects of the STEM education equation that are most often overlooked are the “T” and the “E”– technology and engineering. To help close this gap, you need materials that allow you to provide an engaging, hands-on introduction to technology and essential STEM related concepts. You need fischertechnik.

fischertechnik is the flexible and innovative construction system built around the unique fischertechnik building block, which allows attachment to all six sides. Not only is fischertechik prized by builders and hobbyists of all ages, it is also used extensively in high schools and universities worldwide to explore concepts such as:

Mechanics • Statics • Pneumatics • Physics • Renewable Energies • Electronics • Roboticsfischertechnik is also widely used in industry for vocational training, as well as simulation purposes.

2

Introduction to STEM:

STEM success starts HERE!

Experts agree that success in STEM related fields, both in college and in the working world, is highly dependent upon students developing an interest and ap�tude in STEM as early as possible. With this in mind, fischertechnik called upon noted educator and STEM expert, Tom White, to help them create a line of learning products specifically designed to engage elementary aged students in the world of technology. The result is the fischertechnik Introduc�on to STEM I & II.

The fischertechnik Introduc�on to STEM sets are designed to engage and inspire students in grades 2 through 5. These sets provide educators with the tools they need to help young minds grasp the technology they see around them every day, and to explore and learn about how things work. Both sets provide an engaging integra�on of hands-on projects and standards-based curriculum. This curriculum is specifically designed to meet requirements as outlined in both the Next Genera�on Science Standards, and the Common Core Standards for Literacy and Mathema�cs.

Hands-on, standards-focusedSTEM solutions for grades 2 to 5


Important features of the fischertechnik Introduc�on to STEM sets: • Introduce elementary students to the world of STEM using examples from everyday technology. • Complete with curriculum designed to meet the most current college and career readiness standards. • Each set contains everything needed to build a series of func�onal STEM-focused models using the fischertechnik building system. • Includes a series of concise projects for each indicated grade level that can easily be completed in 45 minutes or less. • Also includes rubrics, student worksheets and teachers answer sheets. • An affordable and easily scalable STEM educa�on solu�on--each set is designed for groups of 2 students, and is fully re-usable. 3

Introduction to STEM I Recommended Grades: 2,3, and 4


Introduction to STEM I #533353The fischertechnik Introduction to STEM I set provides an ideal pathway for introducing students to everyday technology and to enable them to understand how the things around them actually work. Contains 500 pieces along with a detailed, full color 170 page pictorial assembly manual, with instructions for building 40 different models in all. Students can build a centrifugal governor, manual transmission, block and tackle, wind turbine, a beam balance, and more.

Comes packed in sturdy plastic Gratnell storage box.Recommended: 1 set per 2 students

Introduction to STEM I item #533353 $100.00 each

Explore essential STEM concepts, including: • Simple machines • Cause and effect • Energy and matter • Structure and function • Stability and change • Obtaining, evaluating, and communicating information • Energy and motion • How is energy transferred? • Systems and system models • Analyzing and interpreting data • Constructing explanations • Designing solutions

4

Introduction to STEM II#533507An ideal introduction to robotics as encountered in the everyday technology around us. Students can construct 12 easy-to-understand models such as a hand dryer, windshield wipers, a lighthouse with blinking light, merry-go-round, or an automatic sliding door. The ROBO LT Controller, with 3 inputs for sensors and 2 outputs for motors or indicator lights has a USB interface for simultaneous power supply. The ROBO Pro Light software makes programming easy to understand and allows students to get started quickly. Set contains 200 fischertechnik parts, including one ROBO LT Controller (USB interface/USB power supply), ROBO PRO Light software, an XS motor, 2 lights, a lens tip lamp, photo-transistor, and 2 switches.

Comes packed in sturdy plastic Gratnell storage box.Windows based PC required for operation.Recommended: 1 set per 2 students

Introduction to STEM II Recommended Grades: 3,4, and 5


Explore essential STEM concepts, including: • Simple machines • Electrical fundamentals • Introduction to Ohms Law • Motor fundamentals • Introduction to coding (programming) • Matter and weight • Cause and effect • Systems and system models • Developing and using models • Structure and function • Stability and change • Energy and motion • How is energy transferred? • Analyzing and interpreting data • Constructing explanations • Designing solutions

Introduction to STEM II item #533507 $200.00 each

5

STEM Fundamentals SeriesThe fischertechnik Fundamentals of STEM series of sets are an ideal way to explore many important aspects of STEM Education. These sets help to provide the technicians of tomorrow with a hands-on learning experience in the areas of mechanics, pneumatics, physics, simple machinery, electronics and renewable energies.

These sets are widely used in middle and high schools as well as in colleges and universities acrosss the globe. Each set comes with both full color instructions, as well as a black and white, multi-language teaching and activity guide containing material which can easily be incorporated into your classroom activities. Each set comes packed in a convenient plastic Gratnell storage box.


6

Essentials of Mechanical EngineeringMechanics #533021The ideal set for understanding the fundamentals of mechanical engineering. This set enables students to learn, hands-on, how a gear box works, what a planetary gear is and how it works, how the movement of a windshield wiper is produced, how to design a stable bridge or table, and much more.

Includes 500 components for building 30 different models:

Bar • Turntable • Crank Gear 1 • Crank Gear 2 Vehicle 1 • Vehicle 2 • Vehicle 3 • Toothed Gearing with Chains • Vehicle with Steering • GearboxPlanetary Gear • Bevel Gear • Kitchen ApplianceDifferential Gear • Car Jack • Windshield WiperScissor Elevating Platform • Lathe • Four-bar ChainPower Hacksaw Machine • Beam and Scales • CraneScales with Sliding Weight • Lifting Tackle • TableDouble Ladder • Girder Bridge • Bridge with Underbeam Bridge with Upperbeam • High Hunting Stand

Also includes 134 page full color construction booklet with detailed instructions for building all of the above models, as well as a multi-language, black and white teaching guide discussing the various aspects of mechanics and statics, including:

Dynamics • Electric Motors •Worm Gears • Crank Gears Fifth Wheel Steering • Mandril Screw Spindle Joint Rope Pulleys • Bracing...and much more.

Uses a regular 9V battery (not included), or if you prefer, the models can also be powered with either the fi schertechnik Power Set or Accu Set (each sold separately). Comes packed in sturdy plastic Gratnell storage box.

Recommended: 1 set per 2 students


STEM FUNDAMENTALS: Mechanics item #533021 $160.00 each

7

Introduction to Electrical EngineeringElectronics #533029Simple circuits, series and parallel connections, electronic circuits with transistors, capacitors, resistors and LED‘s. Step for step, this construction set teaches the basic principles of electronics. The Electronic-module, a control with 8 fi xed programs, has 2 motor outputs, 3 analog inputs for sensors and potentiometers for controlling the speed of the motor. Many fascinating as well as functional models can be built with this construction set, from a simple fl ash light to ship see-saw, alternating fl asher and controllable ventilating fan.

Set includes 260 parts for building the following models:

Simple Electrical Circuit • Flashlight • Continuity TesterRefrigerator Light • Stamping MachineParallel Connection • Hallway Lighting Merry-Go-Round with Pole Reversing SwitchSimple Flasher • Alternating Flasher • Touch SwitchMerry-Go-Round • Merry-Go-Round with Light BarrierMerry-Go-Round with Touch Switch • Ship See-SawShip See-Saw with Alternating Flasher • Alarm SystemVentilating Fan • Bathroom Fan • Sliding Door

Set includes complete instructions along with multi-language teaching and activity booklet, Electronic-module, XS motor, 2x transistor, 2x capacitor, 3x resistor, 2x mini-switch, phototransistor, temperature sensor, lens tip lamp, 2x LED, battery tray for 9V block.

Requires a regular 9V battery (not included), or if you prefer, all models can also be powered with either the fi schertechnik Power Set or Accu Set (each sold separately). Comes packed in sturdy plastic Gratnell storage box.



STEM FUNDAMENTALS: Electronicsitem #533029 $190.00 each

8

Explore Optical Phenomena & Light


Optics & Lights #533037This set enables students to investigate optical phenomena and experiment with light. The planetary model clearly demonstrates why the moon has phases or why solar and lunar eclipses occur. Optical lenses with various focal lengths, mirrors, lens tip lamps and a variety of other parts allow construction of a microscope, magnifi er, telescope and periscope. With the periscope you can look around corners and the microscope allows you to enlarge very tiny objects. With the sun dial you can determine the time of day, and the model with optical fi ber demonstrates what total refl ection is and how data can be transferred using light. The fi schertechnik Optics & Light set provides a fascinating glimpse into the world of optics.

Includes multi-language teaching and activity guide as well as detailed, step-by-step instructions.

Contains 270 components for building 15 models:

Microscope • Astronomical Telescope • Magnifi er Erecting Telescope • Periscope • Magnifi er with Light Slide Viewer • Sun Dial • Mirror Course Planetary Model • Optical Morse Telegraph Fiber Optic Light Effect • Light Effect with Crank Optical Illusion • Partial and Full Shade

Includes 3 optical lenses (two focal lengths), a Rainbow-LED, mirrors, optical fi ber, and 2 lens tip lamps. Uses a regular 9V battery (not included), or if you prefer, it can also be powered with either the fi schertechnik Power Set or Accu Set (each sold separately). Comes packed in sturdy plastic Gratnell storage box.


STEM FUNDAMENTALS: Optics & Lights item #533037 $130.00 each

9

Fundamentals of Physics


Physics I #533050With this set, students will build 7 different track based coaster style models to learn about and observe fi rst-hand various physical phenomena, such as:

Acceleration • Inertia of Mass • Centrifugal ForceLaw of Conservation of EnergyPrinciple of Linear Momentum • Laws of Motionand more

Instead of being dry, abstract, or diffi cult to understand, this set helps to make the subject of physics engaging, and the concepts clear. Physics becomes fun as balls race on the unique fl ex-rails through various obstacle courses. They accelerate, decelerate, cause chain reactions, shoot through the loop and run through obstacles such as teeter-totters and switches. An elevator powered by a fi schertechnik XS Motor conveys the balls to the top.

The effects of each of these principles are explained in the enclosed activity booklet and can be clearly demonstrated using various experimental set-ups. Includes 690 parts for building 7 different models.

Requires a regular 9V battery (not included), or if you prefer, all models can be powered with either the fi schertechnik Power Set or Accu Set (each sold separately). Comes packed in sturdy plastic Gratnell storage box.


STEM FUNDAMENTALS: Physics I item #533050 $170.00 each

10


Furthers Experiments with PhysicsPhysics II #533053The second fi schertechnik set for exploring physics offers more advanced models, more action, faster speeds and an even larger scale. Featuring all new special parts such as 90° curves, cross-overs and jumps with catch funnel. Once again, learning becomes fun as students observe as the balls race through tight curves and chutes and shoot through different tracks. This second set also utlilizes more sophisticated conveying techniques: for example, now with the new mega model the balls are transported back up by a motor-driven conveying wheel. They are carried even higher by the innovative stage conveyor, which transports the balls one by one all the way to the top in a zig-zag pattern. Once there the balls shoot along their own path downward through the loop, quarterpipe and jumping loop. More ingenious models such as a launching pad, stair step conveyor and chain lift make the subject of conveying technology inspiring.

Set includes multi-language teaching and activity booklet, Mini motor, 2x rainbow LED, 31x track unit, 12x steel ball, 5x 90° curve, cross-over, catch funnel and battery tray for 9V block.

1000 parts in all for building 8 different models.



STEM FUNDAMENTALS: Physics IIitem #533053 $220.00 each

11

Pneumatic PowerPneumatics #533013This educational construction set helps students learn the principles behind pneumatics and uses realistic models to demonstrate how compressors, pneumatic valves and cylinders work. The new, powerful and compact compressor guarantees a reliable supply of compressed air to the models. In addition to vehicles such as front loaders, hay bale pickers and tree trunk grips, other educational models provide students with hands-on knowledge on the subject of pneumatics in combination with the instructional teaching and activity guide with is also included.

Contains 440 components (including a compressor, four pneumatic cylinders, four 4/3-way manual valves, and a battery holder for 9V block batteries) for building 8 different models.

Double Sliding Doors • Scissor Lift • CatapultBalloon Pump • Tree Trunk GripperHay Bale Picker • Front Loader • Excavator




STEM FUNDAMENTALS: Pneumaticsitem #533013 $180.00 each

12

Energy from Wind, Water and SunGreen Energy #533022This set allows students to explore the vitally important world of renewable energy, and helps them answer the question “how can ecological electric power be produced?”. Production, storage and use of electricity from natural energy sources such as water, wind and the sun are graphically illustrated using various models and numerous experiments.

The Gold Cap included for power storage can release the stored power at a slower rate. This helps students to truly understand these energy forms of the future. This set also includes a fuel cell, so students can also learn, hands-on, how it works, and how it generates hydrogen.

Contains over 380 components--including a reversible fuel cell with integrated hydrogen storage unit--for building 19 different models:

Hammer Mill • Water Turbine • Windmill with PumpWindpower Station • Ventilating Fan • Merry-Go-RoundSolar Bicycle Rider • Solar Ferris Wheel Solar Vehicle 1 • Solar Charging Station 1 Electric Vehicle • Solar Parking Barrier Solar Tracking Station • Eco-House 1 • Solar Station 2Fuel Cell Vehicle • Solar Vehicle with 3 Solar Modules Enhnaced Eco-House • Solar Pump with Fuel Cell

Also includes multi-language teaching and activity booklet as well as complete step-by-step assembly nstructions. Parts also include a solar motor (2V), 3 solar modules (1V; 400 mA), Gold Cap power storage device, and an LED ON/OFF switch. Comes packed in sturdy plastic Gratnell storage box.



STEM FUNDAMENTALS: Green Energy item #533022 $280.00 each

13

Drives and How They WorkDrive Systems #533028How does a balloon drive or a bending rod drive work? What is the difference between a friction drive and a rubber-band drive? How can wind be used as a drive? This set provides a glimpse into how different types of drives work. The brawny off-road vehicle with functioning steering and suspension can also be combined perfectly with the Motor Set XM and Control Set for remote control ability. The instructional teaching and activity guide provides a great deal of interesting information on the principles behind the models.

Contains 280 components (including a friction motor) for building 8 different models:

Vehicle with Steering • Balloon Drive • Bending Rod Drive Wind Drive • Off-Road Truck • Buggy with Pullback Motor Rubber Band Motor • Trike with Pullback Motor

Can be combined with Motor Set XM, Control Set, Sound + Lights, and Accu Set for added capabilities.




STEM FUNDAMENTALS: Drive Systemsitem #533028 $110.00 each

14

ADVANCED STEM: ROBOTICS For many years fischertechnik has been at the forefront of robo�cs--in fact, fischertechnik was the very FIRST construc�on set manufacturer to incorporate robo�cs and programming with its sets...way back with the pre-Macintosh Apple computers! The fischertechnik ROBOTICS line allows you to construct fully func�onal robo�c models using the fischertechnik construc�on system, and then program them with your Windows based computer and the easy-to-use ROBO Pro graphic so�ware.

fischertechnik is used around the globe for teaching robo�cs, from elementary school (with the new Introduc�on to STEM sets) on up through college. With fischertechnik, students can build robo�c models of things they encounter everyday--like washing machines and automated ligh�ng systems--to be�er understand how they work. They also can build numerous mobile robots--from simple line-followers, to rescue robots equipped with a full array of sensors, to robots that can even play soccer! What makes fischertechnik’s mobile robots stand out from the compe�tors that rely on using remote controls for their robots, is that with the fischertechnik system, the emphasis is instead on enabling the students to learn how to program the robots to act autonomously, without human interven�on. In addi�on, fischertechnik is especially suited for builiding detailed and sophis�cated simula�on models of the types of machines and automated systems found in industrialproduc�on se�ngs--from simple conveyor belts and punching machines, to extensive sor�ng and storage systems that incorporate robo�c arms, to almost anything you can imagine. Because of this, fischertechnik has also been used by countless corpora�ons such as Porsche, Daimhler-Chrysler, and BMW, for their own in-house voca�onal training and simula�on needs.


15

Introduction to Robotics


Robotics Beginner (LT) #533015Robotics becomes approachable and easy to understand with this complete beginner‘s package for students age 8 and older. With 200 components and the aid of sensors (phototransistor, mini-switches) and actuators (XS motor, indicator lights), students can construct 12 real models such as a hand dryer, stamping machine, lighthouse with blinking light, merry-go-round, or an automatic sliding door.

The ROBO LT Controller, with 3 inputs for sensors and 2 outputs for motors or indicator lights has a USB interface for simultaneous power supply. The ROBO Pro Light software makes programming easy to grasp and allows students to get started quickly. The detailed teaching and activity booklet supports the learning process for students, taking the mystery out of programming.

Set includes one ROBO LT Controller (USB interface/USB power supply), Software ROBO PRO Light, XS motor, 2 lights, lens tip lamp, phototransistor, 2 switchs, and a multi-language teaching and activity booklet.

PC Required for operation.

Recommended: 1 set per 2 students.

ROBOTICS: Robotics Beginner (LT) item #533015 $220.00 each

16

Robotics: Advanced (TXT) #533018Complete robotics set with 310 parts, the all new ROBOTICS TXT Controller and extended ROBO Pro software for control of mobile and stationary robot models.

Features include a USB camera, which allows images to be transferred via USB or WiFi, color recognition, line tracking and motion recognition. The new ROBOTICS TXT Controller has the following features: Color 2.4“ touch display, combined WLAN/Bluetooth module, Micro SD card slot for additional memory space, IR receiver diode, integrated loud speaker, 4 motor outputs, 8 digital/analog inputs for sensors and 4 high speed numerical inputs. With the aid of the ROBO Pro software it is possible to program your own apps for controlling the models with your smartphone/tablet PC (presently for android).

Additional sensors and actuators such as encoder motors, XS motor, mini-switches, NTC resistors, phototransistors and LED‘s allow construction of mobile rover vehicle, surveillance stations, alarm centers, and more. Preprogrammed modules are also provided for beginners. This set is compatible with other fi scheretchnik robotics construction sets. Also includes teaching and activity related material for support of construction and programming.

Set includes one ROBOTICS TXT Controller, ROBO Pro software, USB camera (1 MP), 2x encoder motor, XS motor, 2x LED, 2x switch, phototransistor, NTC resistor.

Recommended: 1 set per 2 students.

REQUIRES: Accu Set for operation (sold separately).

Mobile Robotics with USB Camera


ROBOTICS: Robotics Advanced (TXT) item #533018 $580.00 each

17

Automation & Industrial Simulation Robotics in Industry #533020This set contains 510 components for the construction and testing of four realistic, fully functional, and precisely detailed industrial simulation models:

High Bay Storage Rack System Robot • Gripper RobotPivoting Gripper Robot • Three Axis Robot

This kit includes sturdy fi schertechnik aluminum struts to guarantee maximum stability for all four models. Also includes a full color printed construction booklet with detailed instructions for building all of the above models, as well as a multi-language activity book/ PDF on disc.

Includes 2 Encoder Motors, 2 XS Motors, and 6 sensors.

PLEASE NOTE: This set REQUIRES either theROBOTICS TXT Controller or ROBO TX Controller, ROBO Pro Software, and either the fi schertechnik Accu Set or Power Set (Each sold separately).


ROBOTICS: Robotics in Industry item #533020 $320.00 each

18

Pneumatics & Vacuum TechnologyRobotics & Electropneumatics #533019The subjects of electro-pneumatics and vacuum technology are demonstrated clearly with the aid of fascinating models such as the pneumatic motor, color sorting robot for colored parts, ball obstacle course and pinball machine. The new, powerful and compact fi schertechnik compressor guarantees a reliable and consistent supply of compressed air to the models. The electro-magnetic valves included allow remote control of the models with a PC. Contains 440 components (including compressor, miniature motor, 2x solenoid valves, optical color sensor, vacuum exhauster, 3x cylinders with spring, 2x photo-transistors, 2x lens tip lamps, and 11 fl ex-rails) to build 4 functional models:

Compressed Air Motor • Color Sorting RobotPinball Machine • Ball Obstacle Course

Also includes related instructional material on CD.

REQUIRES: Either the ROBOTICS: TXT Controller or the ROBO TX Controller, ROBO Pro Software and the fi schertechnik Accu Set or Power Set to complete all mod-els and


ROBOTICS: Robotics & Electropneumatics item #533019 $280.00 each

19

NEW!!! ROBOTICS TXT Controller

The compact ROBOTICS TXT Controller (90x90x25mm) can be controlled easily with the color 2.4“ touch display. The combined Bluetooth/WiFi RF module provides the perfect, wireless interface for numerous applications. The numerous interfaces also include a USB host port for USB sticks and other components such as the fi schertechnik USB camera. The integrated Micro SD card slot allows expansion of the memory capacity. Controllers can easily be coupled. REQUIRES Accu Set or Power Set.

› Processor: Dual core, main processor ARM Cortex A8 (32bit/500mHz) + Cortex M3› Memory capacity: 128 MB DDR3 RAM, 64 MB Flash› Memory expansion Micro SD card slot› Display: Color 2.4“ touch display (320x240 pixels)› 8 Universal inputs: Digital/analog 0-9VDC, analog 0-5 kΩ› 4 high speed numerical inputs: Digital, frequency up to 1kHz› 4 Motor outputs 9V/250mA (max: 800 mA): speed infi nitely controllable, short-circuit proof, alternative 8 single outputs for components such as lights, etc.› Combined Bluetooth/WiFi RF module: BT 2.1 EDR+ 4.0, WLAN 802.11 b/g/n› Infrared receiver diode: for fi schertechnik Control Set transmitter› USB 2.0 Client: Mini USB port for connection to PC› USB Host interface: USB A port for fi schertechnik USB camera, USB sticks, etc.› Camera interface: over USB Host, Linux camera driver integrated into operating system› 10-pin male connector for additional inputs and outputs as well as I2C interface› Integrated loud speaker› Integrated real time clock with exchangeable buffer battery: for capturing measured values within a defi ned period of time› Linux-based open source operating system› Programming possible with ROBO Pro, C-Compiler, PC-Library, and many others.› Link to smartphones/tablet PC‘s via Bluetooth or WLAN, allowing them to be used as terminals for the controller. Programming using ROBO-Pro software.› Dimensions: 90x90x25 mm› Power supply: 9V DC 3.45 mm socket, or 2.5 mm fi schertechnik sockets (for Accu Pack)


ROBONEW!!! ROBONEW!!! ROBO

Features include:

WiFiBluetooth500MHZ Dual ProcessorTouch DisplayIntegrated Loud SpeakerUSB Host InterfaceMicro SD Card Slotand much more!

ROBOTICS: TXT Controller item #522429 $400.00 each

20

Software and Power Options for fischertechnik Sets

ROBO Pro Software

Accu Set - NiMH Battery & Charging Unit

ROBO Pro Software Single User License #93296 Unlimited School Site License #92298 Easy to use programming software. Even beginners can quickly begin programming through the use of simple fl ow charts consisting of various software building blocks. The exchange of information can be done through variables and graphical connections as well. This allows the program functions to be displayed in a clear and understandable manner. Compatible with Windows XP, Vista, 7, or 8.

fi schertechnik PLUS Accu Set #57487Battery charger with microcontroller for reliable protection from overcharge. Very short recharging time, max 2 hours. High-powered NiMH Accu Pack with short circuit protection, 8.4V/1500 mAH. 120V~/60Hz. Ideal for powering mobile fi schertechnik models.

Power Set - Plug-In Power with Variable Controllerfi schertechnik PLUS Power Set #91087Power unit with infi nitely variable control unit. Plug in Class-2 Transformer. Input AC 120 V 60 Hz 150mA. Output :DC 9V 1A. Ideal for powering stationary fi schertechnik models.


Power Set - Variable Control Unit & AC Adapter item #91087 $72.00 each

Accu Set - Rechargeable Battery Pack & Charger item #57487 $86.00 each

ROBO Pro Programming Software item #93296 (Single User) $36.00 each item #93298 (Site License) $140.00 each

21

Standards Based Curriculum Solutions: fischertechnik STEM Lab Program

Project Based Learning: Focus on StandardsThe fischertechnik STEM Lab Program offers an ideal integration of project-based learning and standards-based curriculum. Created to promote inquiry, design and problem solving, this program was especially developed for use with the fischertechnik construction system.

By combining curriculum with hands-on exploration and creation, this program offers an effective turn-key or customizable solution for STEM Education. Each level – Middle and High School – consists of various theme projects which enable students to explore and understand essential Science, Technology, Engineering and Mathematics concept areas.

Curriculum By Educator and STEM Expert, Tom White“I’ve purposefully created this fischertechnik STEM program to meet Common Core Standards for Math,

Reading and Writing as well as the National Science Education Standards, and standards of ISTE, ITEEA. This program can easily fill six months of class time and engage students in the study of applied physics with a

systems approach to electronics, control and sensing.”

— Tom White, Program Creator

The fischertechnik STEM Lab Program is designed to offer a comprehensive, project based STEM education solution, one that will specifically address current academic standards. These standards include the Common Core standards for Math, Science, Reading and Writing, as well as NSES Content Standards, Standards for Technological Literacy and ISTE standards. The curriculum for this program was put together by noted educator and STEM expert, Tom White. The program is designed to provide enough material for at least 75 academic hours at the middle school level, and at least 150 academic hours at the high school level. The middle school level is geared to providing an overview of various STEM related areas (with a focus on energy, power and robotics), and the high school section is focused on the area of Mechatronics. Each lab set includes complete, day-by-day curriculum, combined with the state-of-the-art fischertechnik construction system, to provide what is essentially a turn-key STEM education solution for middle and high schools that are looking for an engaging and affordable way to address this vital area.

Both the Middle School and High School curriculum are broken down into a series of project themes, where different skills and subjects are addressed, each area being more complex than the one before. Each day of activities in these sub-projects provides building blocks of learning which the students will use in completing a large scale project at the end which requires them to see the big picture and how everything they’ve learned fits together.

Each project theme clearly spells out—for both students and teachers—the purpose of the specific project, the concepts to be addressed, and an outline of exactly what will be covered as the project is addressed. Students are asked an essential question, which will require them to understand all the parts of the project to answer properly. They are given a real-world scenario, which helps to clearly provide an answer to the eternal question, “where will I ever use this?”. They are then provided with a daily plan, which provides not only the expectations for the project, but also a guideline of what they will need to accomplish each step of the way. The standards for each project theme area are also detailed—and keep in mind, these standards include the new Common Core standards which are taking effect right now. Assessment guidelines and rubrics are included as well.


22

Curriculum Solutions: fischertechnik STEM Lab Program (continued)


STEM LAB 1: Energy, Power, Robotics #519340 Project Themes Include:• Sketching and Documentation• Structures• Mechanical Systems• Electronic Systems• Control Systems• Sensor Systems• Motors and other Actuators• Automation• Fundamentals of Robotics RoboticsRecommended: 1 set per 2 students.

STEM LAB 2: Mechatronics #519341Project Th

• Sketching and Documentation• Introduction to Energy and Power• Energy Conversion Systems• Conversion and Storage of Energy• Simple Machines• Mechanisms• Basic Electricity• Introduction to Control Systems• Human/Machine Collaboration RoboticsRecommended: 1 set per 3 to 4 students.

With the fischertechnik STEM Lab Program, everything you need is right in the boxThe nice thing about the fischertechnik STEM Lab program is that everything you need is included right in the box. You don’t have to order lot’s of separate parts and software and curriculum materials, because it’s already been put together for you. First off, each fischertechnik STEM Lab kit is packed in it’s own sorting box for organized storage. Not only that, but each and every set includes all the parts needed to complete the various projects addressed throughout the program, the ROBO Pro programming software, a rechargeable battery pack, and one ROBO TX Controller. And of course every set includes a disc with the complete curriculum in both the student and teachers version.And the curriculum included in each set is yours to use this year, next year and for years after that. There are NO additional fees or subscription charges.

The fischertechnik STEM Lab Program has been designed to make it easy to offer a hands-on, project based learning experience to your students. Experts agree that project based learning solutions such as this can be one of the most effective methods known for teaching essential STEM related concepts.

Project Themes Include: • Sketching and Documentation • Introduction to Energy and Power • Energy Conversion Systems • Conversion and Storage of Energy • Simple Machines • Mechanisms • Basic Electricity • Introduction to Control Systems • Human/Machine Collaboration • Introduction to Sensors • Mobile Robotics

Project Themes Include: • Sketching and Documentation • Structures • Mechanical Systems • Electronic Systems • Control Systems • Sensor Systems • Motors and other Actuators • Automation • Fundamentals of Robotics • Mobile Robotics

STEM LAB 1: Energy, Power, and Robotics item #519340 $895.00 each

STEM LAB 2: Mechatronics item #519341 $995.00 each

23

fischertechnik Robotics Competition Lab with Curriculum #519143

The fischertechnik Robotics Competition Lab (#519143) is designed for educational institutions that want to involve their students in mobile robotics competitions, involving models of online followers, maze explorers, and such. This is the ideal fischertechnik set for participation in RoboCupJunior, and various other competitions around the world. The lab combines the complete contents of the ROBO TX Training Lab and ROBO TX Explorer sets, along with a fischertechnik Accu Set, to provide everything you need, in one special storage container, to build the ultimate fischertechnik mobile robot.

The Robotics Competition Lab consist of over 700 pieces, including structural components gears, pulleys, DC motors, motors with integrated encoders, gearboxes, and all fischertechnik family sensors such as an ultrasonic distance sensor, the photo-transistor, the photo resistor, NTC resistor, the color sensor, the infrared sensor track follower, and more. It also includes the new ROBO TXT Controller interface,with touch screen, the Accu Set (battery pack and charging unit) and the ROBO Pro soft-ware used for all programming. Includes full color printed instructions for building 17 different models, along with the complete ROBO TX Controller manual, and additional activities materials on enclosed disc.

More than just a collection of parts, the fischertechnik Robotics Competition Lab also includes complete, standards based classroom curriculum, designed to fill well over 50 classroom hours of activities. This curriculum was created by noted educator and STEM expert,

Tom White. Students will learn about the fundamentals of programming (such as open and closed loop programming, combinational logic, programming with variables, subprograms and more), as well as about the different types of sensing systems used on their robots. The curriculum is broken down into a small group of project themes. Each project theme clearly spells out - for both students and teachers - the purpose of the specific project, the concepts to be addressed, and an outline of exactly what will be covered as the project is addressed. Students are asked an essential question, which will require them to understand all the parts of the project to answer properly. They are given a real-world scenario, which helps to clearly provide an answer to the eternal question, “where will I ever use this?”. They are then provided with a daily plan, which provides not only the expectations for the project, but also a guideline of what they will need to accomplish each step of the way. The standards for each project theme area are also detailed—including the new Common Core Standards which are taking effect right now. These standards are specific to each project, and include Math Standards, Standards for Technological Literacy, ISTE Technology Foundation Standards, and also the Reading and Writing Standards for Literacy in History, Social Studies, Science and Technical Subjects. Assessment guidelines and rubrics are included as well.


Standards Based Curriculum Solutions: Robotics Competition Lab


Robotics Competition Lab Set item #519143 $991.00 each

24

ROBO TX Explorer - Ideal for Competitionsfischertechnik ROBO TX Explorer #508778Explore unknown areas, measure distances, follow trails, show driving directions by means of blinking signals, recognize colors, measure temperatures, avoid obstacles without touching them, recognize day and night, turn headlights on and off automatically, trigger an alarm, and more! The ROBO TX Explorer set comes with an assortment of special sensors (the NTC resistor, the photo-resistor, the ultrasonic distance sensor, the infrared color sensor and the specially developed trail sensor) to enable you to do all these things and much more. And thanks to two encoder motors, the tracks of your robotic creations can be controlled precisely and steered synchronically. With the rescue robot (one of the six models you can build with this set) you have the ideal basis for participation in the RoboCup.

Contains 400 components for building the following models:

Basic Model • Trail Searcher • Tunnel RobotColor Detector • Explorer • Rescue Robot

Includes two encoder motors, three indicator lights, buzzer, optical color sensor and an IR Trail Sensor. Also includes 26 page full color construction booklet with detailed instructions for building the above models, as well as a multi-language, black and white activity booklet that provides an overview of the encoder motor and various sensors, as well as an introduction to programming uing the fischertechnik ROBO Pro software.

REQUIRES: Either the ROBOTICS: TXT Controller or the ROBO TX Controller, ROBO Pro Software and Accu Set to complete all models and perform all activites (each sold separately).


ROBOTICS (Classic): ROBO TX Explorer item #508778 $260.00 each

25

Simulation & Training: Conveyor Belt

Simulation & Training: 3-Axis Robot with Gripping Device

#50463 - 9V with ROBO TX Controller#50464 - 24V without PLC (required)Length 275 mm, transports workpieces with a diameter of up to 29 mm. Several conveyor belts can be connected to each other to form a conveyor belt of any length.

Scope of Delivery:• 1 DC motor, 1 sensing device (potential-free), choice as pulse counter, can be used for distance traveled or as an activation button; 2 light barriers consisting of phototransistor and lens tip bulb, which can be connected together to an output for the control or directly to the power supply• 1 workpiece diameter 29 mm, h=25 mm• Model is mounted on stable wooden board, carton packaging• 3 digital inputs• 1 output, 9V –.../24V –... (1 motor for drive for conveyor belt)Port: PCB with relais to reverse polarity of motor, multi pin connector (26 pins, grid 2,54mm) and in addition PCB terminals with push in connection for all I/O

#511937 - 9V with ROBO TX Controller#511938 - 24V without PLC (required)3-axis robot with gripping deviceDegrees of freedom:Shaft 1: Rotation 180°Shaft 2: Forward/back 90 mmShaft 3: Up/down 150 mm

Scope of Delivery:• 4 DC motors, including 2 with integrated magnetic encoder (max. pulse frequency: 1 kHz)• 4 Limit switches, 2 pulse sensors for path measurement• 8 Digital inputs• 8 Outputs, 9V –.../24V –... (4 motors clockwise/ counterclockwise rotation, 24V version includes relay board for motor polarity reversal)• Model mounted on stable wooden board, carton packaging• Model can be ideally combined with conveyor belt, punch press and intermittent assembly line Port: PCB with relais to reverse polarity of motor, multi pin connector (26 pins, grid 2,54mm) and in addition PCB terminals with push in connection for all I/O


Simulation & Training - for Higher Education & Industrial UseThe line of fischertechnik Training and Industrial Simulation models are designed to provide users with a collection of pre-assembled, compact models of automated machines commonly found in modern industrial settings. They are used worldwide in advanced classroom and industrial training situations, as well as by many corporations for building working simulations of actual production lines.

These models are available in both regular 9V versions (fully wired with the ROBO TX Controller), as well as industry standard 24 V versions for use with a PLC unit (not included).

3-D (Three Axis) Robot

#511937 9V version $1298.00 each #511938 24V version $1149.00 each

Conveyor Belt


26

Simulation & Training: Punching Machine with Conveyor Belt

Simulation & Training: Indexed line with Two Machining Stations

Simulation & Training: Pneumatic Processing Center

#51663 - 9V with ROBO TX Controller#96785 - 24V without PLC (required)Conveyor belt with two light barriers, one machining station, and one workpiece.

Scope of Delivery:• 2 DC motors, 2 limit switches (potential free), 2 light barriers consisting of phototransistor and lens tip bulb• Model is mounted on stable wooden board, carton packaging• 4 digital inputs• 4 output, 9V –.../24V –(2 motors counter-clockwise, clockwise rotation)• Ribbon cable, 14-pin and color coded with 14-pin pin connector, (only for 24V version)

Port: PCB with relais to reverse polarity of motor, multi pin connector (26 pins, grid 2,54mm) and in addition PCB terminals with push in connection for all I/O

#51664 - 9V with ROBO TX Controller#96790 - 24V without PLC (required)Conveyor belt, arranged in U-shape, for intermittent transport and for the machining of several workpieces.

Scope of Delivery:• 2 machining stations, 4 conveyor belts, 8 DC motors, 4 limit switches (potential free), 5 light barriers consisting of phototransistor and lens tip bulb• Model is mounted on a stable wooden board, carton packaging• 9 digital inputs• 10 outputs, 9V –.../24V –... (6 motors with one direction of rotation, 2 motors counter-clockwise, clockwise rotation)


#524064 - 9V with ROBO TX Controller#520529 - 24V without PLC (required)Machining center with bin for workpieces, turntable, machining station, compressor and conveyor belt forthe transport of workpieces.

Scope of Delivery:• One double-action and two single-action pneumatic cylinders, four 3/2 way magnetic valves, 1 DC motor, 4 switches (potential free), 2 light barriers consisting of phototransistor and lens tip bulb• Model is mounted on a stable wooden board• 6 digital inputs• 6 outputs, 9V –.../24V –..



Pneumatic Processing Center


Indexed Line with 2 Machining Stations


Punching Machine with Conveyor Belt


27

STEM History: The innovations of Leonardo da Vinci

fi schertechnik da Vinci Machines #500882This construction set allows students to re-create several of the mechanical marvels originally conceived by Leonardo da Vinci. This is history you can touch! Over 250 components for building the following models:

Mechanical Wings • Blacksmith’s Tong’s • Crane with Pawl • ChariotStone Tongs • Self-releasing Hook • Catapult • Scaling LadderDrum Wagon • File Cutting Machine • Swing Bridge

Includes 54 page full color construction book with detailed instructions for building all of the above models, a multi-language, black and white activity booklet with background on Leonardo daVinci and his inventions, as well as various suggested tasks for students to interact with the models


STEM History: da Vinci Machines item #500882 $86.00 each

28

STEM History: Inventors and their Milestones in Technology fi schertechnik Technical Revolutions #508776

Important moments in the history of technology are brought to life as students construct functional models based on the designs of James Watt, Michael Faraday, and other famous inventors. Build 12 different models, including an electric motor, a cardan shaft, a perpetuum mobile, a Morse telegraph, and a generator. Includes an informative black & white teaching and activity guide.

Michael Faraday James Watt

Contains 270 components for building the following 12 models:

Safety Elevator • Electric Motor • Generator • Helicopter Synchronous Wiper • Cardan Shaft • Morse Telegraph Counter-Rotating Wiper • Parallelogram Wiper Centrifugal Governor • Perpetuum Mobile Hair Hygrometer

Includes 42 page full color construction book with detailed instructions for building all of the above models, as well as a multi-language, black and white teaching guide/activity booklet with background information on the inventors behind these ground breaking creations, as well as various suggestedtasks for students to interact with the models Requires 9 V battery (not included)

Includes 42 page full color construction book with detailed instructions for building all of the above models, as well as a multi-language, black and white teaching guide/activity booklet with background information on the inventors behind these ground breaking creations, as well as various suggested


STEM History: Technical Revolutions item #508776 $115.00 each

29

fischertechnik Motor Set XM #505282High performance geared motor in compact plastic casing with numerous possibilities for attachments. With many toothed gears, axles and gearbox parts. 45 Individual parts.

Performance data: Voltage 9V –..., max. output 3.0 W at about 340 RPM. REQUIRES Accu Set (57487) or Energy Set (#91087) for operation--sold separately.

PLUS - Motors, Light, Sound & Storage SolutionsBattery Powered Motor High Performance Geared Motor

Remote Control

fischertechnik Motor Set XS #505281Small, compact geared motor in plastic casing with numerous attachment and connection possibilities. With many toothed gears, axles, driving gears and safety battery tray with pole-reversing switch.

Technical Data: 9V, max 1 W at 6000rpm.REQUIRES 9V battery--not included.

fischertechnik Control Set #500881The four channel infrared remote control allows you to control fischertechnik models from a distance. Up to three motors and one servo can be driven proportionally. This means an infinitely variable turning angle of the steering wheel and infinitely variable speed control. Up to four receivers can be operated with the remote control; which allows numerous operational possibilities. The set contains a controller, receiver and a servo.

• Universal proportional 4-channel infrared remote control for motorized models.

• Powerful infrared transmitter : 9V, 3 transmission diodes.

• Microprocessor controlled receiver 9V, 1A max for 3 motors and one servo

• Microservo 4.8/6V, angle +/40 degrees, 1.7 kg cm max

• Two different frequencies can be selected

• Can drive two receivers per frequency.

• Cruise control, motor speed, which was set, remains.

• Crawler function, easy steering of models with 2 drive motors, for example tracked vehicles with a joystick.

REQUIRES power supply (NOT INCLUDED): Transmitter: 9V Alkaline Battery Receiver: Accu Set(#57487)


Motor Set XM item #505282 $52.00 each

Motor Set XS item #505281 $52.00 each

Control Set item #500881 $100.00 each

30

fischertechnik Creative Box 1000 #91082The perfect addition to any fischertechnik collection. A deluxe storage box filled with more than 700 components from the current fischertechnik assortment of individual parts.

The many parts are packed and delivered in the time-tested storage Box 1000 (#30383), the sturdy plastic box with 8 sorting trays, 32 sorting spacers and the functional base plate 390 x 270 mm as a lid.


Add Light and Sound to your fischertechnik Models

Storage Box Spare Parts & Storage

fischertechnik Sound + Lights #500880

If you want to breathe more ”life” into the fischertechnik models using sounds and lights then the ”Sound+Lights” set is the ideal solution! Up to three different sounds, which can be activated with push buttons or automatically with digital inputs, are available on the sound module. Depending on the requirement, the sounds can be replaced very simply per USB. The blink connection, which is also included, allows the operation of up to eight lights as blinking lights. The set contains a sound module with blink electronics, a USB cable, two lights with various colored luminous caps and a battery tray for a 9V block (battery not included). Windows compatible only.

fischertechnik Box 1000 #30383The ideal storage solution for all fischertechnik construction elements. This giant fischertechnik storage box consists of a base plate and box (390x270mm), eight sorting pans (128x188mm) and 32 partitions.

DOES NOT INCLUDE ANY ASSEMBLY INSTRUCTIONS OR COMPONENTS.

Look at what people are saying about fischertechnik...“fischertechnik... it is made with an accuracy and in materials which would not be out of place in a space programme.” Andrew Lucas, Design Journal #260

“The Rolls-Royce’s of construction toys” Gordon McComb, Michael Predko and Myke Predko “The Robot Builder’s Bonanza” (3rd edition, McGraw-Hill, 2006)

“I have used (fischertechnik) for the past ten years or so. They are a nice way to get the students involved in some hands-on work and a nice way to get them thinking about robotics and automating systems. The students enjoy them, and I think it helps to connect the theory to the practical.” John Bramley, educator, Hillsboro-Deering High School, New Hampshire

“I burst open the (fischertechnik) box and was totally amazed at the quality of the pieces and the ingenuity of it all. I did further on-line research on fischertechnik and was amazed....fischertechnik was beyond my imagination.” Dexter Mahadeo, parent

Creative Box 1000 item #91082 $150.00 each

Box 1000 (Storage Only) item #30383 $48.00 each

Sound + Lights Set item #500880 $70.00 each

31

fischertechnik Education products are distributed exclusively in the USA by Studica, Inc. , and are available from

www.mgtechstem.comb

M & G Technology401 19th Street N. Bessemer, AL 35020

(205) 910-7274 • email: [email protected]

stem focused classroom & training solutions • 2015 … · stem focused classroom &...

Documents