Getti ng Started Gui deFASTFIND LINKSMK-97DF8032EN-13*043-100478-01*043-100478-01Hitachi AMS 2500Getting Started Guidei iHit achi AMS 2500 Get t ing St art ed GuideCopyright 2011 Hit achi Lt d., Hit achi Dat a Syst ems Corporat ion, ALL RI GHTS RESERVEDNot ice: No part of t his publicat ion may be reproduced or t ransmit t ed in any form or by any means, elect ronic or mechanical, including phot ocopying and recording, or st ored in a dat abase or ret rieval syst em for any purpose wit hout t he express writ t en permission of Hit achi, Lt d. and Hit achi Dat a Syst ems Corporat ion ( hereinaft er referred t o as Hit achi Dat a Syst ems ) .Hit achi, Lt d. and Hit achi Dat a Syst ems reserve t he right t o make changes t o t his document at any t ime wit hout not ice and assume no responsibilit y for it s use. Hit achi, Lt d. and Hit achi Dat a Syst ems product s and services can only be ordered under t he t erms and condit ions of Hit achi Dat a Syst ems' applicable agreement s. All of t he feat ures described in t his document may not be current ly available. Refer t o t he most recent product announcement or cont act your local Hit achi Dat a Syst ems sales office for informat ion on feat ure and product availabilit y.This document cont ains t he most current informat ion available at t he t ime of publicat ion. When new and/or revised informat ion becomes available, t his ent ire document will be updat ed and dist ribut ed t o all regist ered users.Hit achi is a regist ered t rademark of Hit achi, Lt d. in t he Unit ed St at es and ot her count ries. Hit achi Dat a Syst ems is a regist ered t rademark and service mark of Hit achi, Lt d. in t he Unit ed St at es and ot her count ries.All ot her t rademarks, service marks, and company names are propert ies of t heir respect ive owners.1Hit achi AMS 2500 Get t ing St art ed GuideHi t achi AMS 2500Get t i ng St ar t ed Gui deCongr at ul at i ons on pur chasi ng t he Hi t achi Adapt abl e Modul ar St or age ( AMS) 2500 st or age sy st em.Before using your st orage syst em, some st eps are required t o inst all and configure t he syst em and prepare your host server. The inst ruct ions in t his guide are designed t o get your st orage syst em up and running quickly. I f you prefer det ailed inst ruct ions, please refer t o t he following: AMS 2500 St orage Syst em Hardware Guide ( MK- 97DF8007) on t he CD supplied wit h t he st orage syst em. St orage Navigat or Modular Users Guide ( MK- 97DF8008) on t he CD supplied wit h t he st orage syst em. St orage Navigat or Modular 2 st orage management soft ware ( hereinaft er referred t o as Navigat or 2) . To access t he help, eit her: I nst all t he Navigat or 2 soft ware using t he inst ruct ions in t his guide, t hen click Hel p on t he current screen being viewedOR Click Hel p > Hel p in t he main menu.2Hit achi AMS 2500 Get t ing St art ed GuideI nst al l at i on & conf i gur at i on checkl i stThe following checklist ident ifies t he st eps for get t ing your AMS 2500 st orage syst em up and running. Please check each st ep as you complet e it and record your set t ings on page 45.Pr epar i ng f or t he i nst al l at i on 1. Prepare t he sit e ( page 3) 3. User- supplied it ems ( page 5) 4. I dent ify your configurat ion ( page 8)I nst al l i ng t he st or age syst em 5. I nst all t he base and expansion unit s ( page 9) 6. At t ach expansion unit s ( opt ional) ( page 9) 7. Connect cables t o t he base unit ( page 11) 8. Connect t o a Modular 2U SAS Expansion Unit ( opt ional) page 13 9. Power- up t he base unit ( page 14) 10. At t ach t he front bezel ( page 15)Conf i gur i ng t he st or age syst ems 11. Set Java Runt ime paramet ers if necessary ( page 16) 12. I nst all and log in t o Navigat or 2 ( page 17) 13. Add st orage syst ems ( page 18) 14. Perform t he init ial set up ( page 21) 15. Add t he newly configured st orage syst em t o Navigat or 2 ( page 42)Please read t he Release Not es before inst alling or using t his product . They may cont ain requirement s and rest rict ions not fully described in t his document , along wit h updat es and correct ions t o t his document .3Hit achi AMS 2500 Get t ing St art ed GuidePr epar i ng f or i nst al l at i on1. Pr epar e t he si t ePlanning t he proper locat ion and layout of t he Hit achi AMS 2500 st orage unit is essent ial for it s successful operat ion. The sit e where you inst all t he st orage unit can affect it s performance. For example, equipment placed t oo close t oget her or in an inadequat ely vent ilat ed area can cause over-t emperat ure condit ions. I n addit ion, poor equipment placement can make t he rear panel inaccessible.To ensure normal operat ion and avoid unnecessary maint enance, plan your sit e configurat ion and prepare your sit e before inst allat ion. The sit e you choose for t he Hit achi AMS 2500 st orage unit should: Be fairly cool and dry for t he accept able t emperat ure and humidit y ranges: Maximum t emperat ure: 104 F ( 40 C) Relat ive humidit y ( non- condensing) : 8% t o 80% Be free of st rong elect romagnet ic field generat ors ( such as mot ors) , vibrat ion, dust , and direct exposure t o sunlight . Provide a st urdy, level surface t hat can support t he unit . A fully populat ed unit weighs approximat ely 4,686 lbs. ( 2, 130 kg. ) . Be wit hin six feet ( 1. 82 met ers) of a power out let . Allow for at least six inches ( 152. 3 mm) of space at t he front and back of t he st orage syst em for vent ilat ion. Not place t he unit next t o, on t op off, or below any device t hat generat es heat or will block t he fee flow of air t hrough t he unit s vent ilat ion slot s.Figure 1- 1 on page 4 shows t he inst allat ion and service clearance area for t he Hit achi AMS 2500. Measurement s shown are in millimet ers. For more informat ion about select ing a locat ion, refer t o t he AMS 2500 St orage Syst em Hardware Guide ( MK- 97DF8007) .4Hit achi AMS 2500 Get t ing St art ed GuideFi gur e 1-1: I nst al l at i on Ar ea and Ser vi ce Cl ear ance2. Unpack i t emsa. I nspect all shipping cart ons for signs of damage. I f you see damage, cont act t he shipper.b. Loosen t he band around t he cart ons and open all cart ons.c. Remove all accessory boxes, packing mat erials, and envelopes from t he cart ons.d. Have at least t hree people remove t he base unit and any expansion unit s.e. Open and remove t he bag in which t he base unit is enclosed. Repeat t his st ep for any expansion unit s you may have ordered.f. Compare t he it ems received t o t he packing list . I f any it ems are missing or damaged, cont act t he shipper immediat ely.610110075150170 270501601020885735200 or mor e601351100G44742. 512. 5525585 12. 5Fl oor Ti l e Cut out f or Rout i ng Cabl esLevel i ng Bol tCast erMai nt enance Ar ea Boundar yPer f or at ed Fl oor Ti l e - 450mm x 450mm ( f or f l oor v ent i l at i on)Fr ont Si de of Rack5961020610Legend32205Hit achi AMS 2500 Get t ing St art ed Guideg. Each base unit has a key for locking and unlocking t he front bezel. Place t he keys in a safe place.h. Please keep all packing mat erials and cart ons in case you need t o t ransport or ship t he base or expansion unit .3. User -suppl i ed i t emsTo complet e your inst allat ion, you need t he following it ems.Requi r ement s f or al l i nst al l at i ons A personal comput er ( PC) t hat will act as a management console ( see Requirement s for st orage syst em management on page 6) The Hit achi AMS2xxx rack or an equivalent rack Two AC out let s ( 100 V t o 120/ 200 V t o 240 V) A host server equipped as described under Host server requirement s on page 7 I nt ernet access and a support ed browser, wit h pop- up blockers disabled ( see Requirement s for st orage syst em management on page 6)Fi bre Channel i nst al l at i on r equi r ement s A mult imode fiber- opt ic cable for each Fibre Channel port t hat will connect t o your st orage net work ( see Table 1- 1) A host server t hat cont ains at least one Fibre Channel host bus adapt er ( HBA) ( see Host server requirement s on page 7) Opt ional: a Fibre Channel swit ch for swit ch configurat ions1 Gbps i SCSI i nst al l at i on r equi rement s An I P address, subnet mask, gat eway ( if applicable) , and 5e or cat egory 6 Et hernet cable for each 1 Gbps iSCSI dat a port t hat will connect t o your st orage net work A host server t hat cont ains at least one iSCSI host bus adapt er ( HBA) or net work- int erface card ( NI C) , and a support ed iSCSI init iat or ( see Host server requirement s on page 7)Tabl e 1- 1: Suppor t ed Fi ber - Opt i c Cabl es and Di st ancesCabl e Lengt hDi st anceLPe1150 ( @ 4Gb/ s)LPe1250 ( @ 8Gb/ s)Max 50/ 125 mult imode fibre cable ( 2000MHz* km bandwidt h)OM3 ( limit ing opt ical receiver, 800- M5E- SN- I )1246. 71 feet( 380 m)492.12 feet( 150 m)50/ 125m ( 500MHz* km bandwidt h)OM2 ( limit ing opt ical receiver, 800- M5- SN- S)492.12 feet( 150 m)164.04 feet( 50 m)62. 5/ 125m ( 200MHz* km bandwidt h)OM1 ( limit ing opt ical receiver, 800- M6- SN- S)229.65 feet( 70 m)68.89 feet( 21 m)6Hit achi AMS 2500 Get t ing St art ed Guide Opt ional: a Gigabit Et hernet LAN swit ch for swit ch configurat ions10 Gbps i SCSI i nst al l at i on r equi r ement s An I P address, subnet mask, gat eway ( if applicable) , and eit her a 50/125m mult imode OM2 or OM3 cable for each 10 Gbps iSCSI dat a port t hat will connect t o your st orage net work. A host server t hat cont ains at least one iSCSI host bus adapt er ( HBA) or net work- int erface card ( NI C) , and a support ed iSCSI init iat or ( see Host server requirement s on page 7) Opt ional: a 10 Gbps Et hernet LAN swit ch for swit ch configurat ionsRequi r ement s f or st or age syst em management An I P address for each management port on t he base unit A PC t hat will act as a management console and meet s t he following requirement s:Processor: 1 GHz ( 2. 4 GHz recommended)Random Access Memory: 1 GB ( 2 GB recommended)Disk space: 1. 5 GB or moreVideo resolut ion: 800 x 600 dot s per inch ( 1024 x 768 or higher recommended) , 256 colors or moreA net work- int erface card ( NI C)An Et hernet LAN cable t o at t ach t he management console t o t he st orage syst ems management port s. The management port s support Aut o- MDI / MDI X t echnology, allowing you t o use eit her st andard ( st raight - t hrough) or crossover Et hernet cables. One of t he following operat ing syst ems:Microsoft Windows XP ( Service Packs 2 and 3)Microsoft Windows 2003 ( Service Packs 1 and 2) x86 onlyMicrosoft Windows 2003 R2 ( no Service Pack, Service Packs 1 and 2) x86 and x64Microsoft Windows Vist a ( Service Pack 1) 86 onlyMicrosoft Windows Server 2008 ( Service Pack 2) x64 and x86Microsoft Windows 7, x64 and x86 ( no Service Pack)Microsoft Windows Server 2008 R2 ( no Service Pack)Red Hat Ent erprise Linux 4 ( Updat e 1) x86 onlyRed Hat Ent erprise Linux 4 ( Updat e 5) x86 onlyRed Hat Ent erprise Linux 5 ( Updat e 3) x86 onlyRed Hat Ent erprise Linux 5 ( Updat e 4) x86 and x64Solaris v8, v9, and v10 SPARC only, Solaris 10 x64 ( AMD64)TI P: For an opt imum experience wit h Navigat or 2, we recommend t hat your management console be a new or dedicat ed PC.7Hit achi AMS 2500 Get t ing St art ed Guide One of t he following Web browsers, wit h pop- up blockers disabled and Java Runt ime Environment ( JRE) v6. 0 inst alled ( JRE v6. 0 can be downloaded from ht t p: / / j ava.com/ en/ download/ and inst alled by following t he on- screen prompt s) :I nt ernet Explorer 6 for Microsoft Windows 2000, XP, and 2003I nt ernet Explorer 7 for Microsoft Windows XP, 2003, 2008, Vist aMozilla 1. 7 for Red Hat Ent erprise Linux 4 Updat e 1, Updat e 5, 5. 0 Updat e 3 and 4Mozilla 1. 7 for Solaris v8, v9, and v10Firefox2 for Solaris 10Host ser ver r equi r ement sA host server equipped as follows: A support ed Fibre Channel HBA for Fibre Channel inst allat ions, or an iSCSI HBA, NI C, and iSCSI init iat or for iSCSI inst allat ions One of t he following host operat ing syst ems:Apple Macint osh OS10 ( Fibre Channel only)AsianuxHP- UXI BM AI X v5. 1, v5. 2, v5.3, v6.1, and v7. 1Microsoft Windows 2000 ( Service Packs 3 and 4)Microsoft Windows 2003 and 2003 Server ( Service Pack 1)Microsoft Windows 2008 ( Service Pack 2)Microsoft Windows XP ( Service Pack 2)Net Ware v6. 5 Service Packs 6 and 7 ( Fibre Channel only)Red Hat Ent erprise Linux 4 ( Updat e 1)Red Hat Ent erprise Linux 4 ( Updat e 5)Red Hat Ent erprise Linux 5 ( Updat e 3)Red Hat Ent erprise Linux 5 ( Updat e 4)Sun Solaris v8, v9, and v10SuSE LinuxNOTE: The Navigat or 2 command- line int erface also support s t he following operat ing syst ems: HP- UX 11.0, 11i, 11i v2. 0, and 11i v3.0; I BM AI X 5.1, 5. 2, and 6. 1; and I RI X 5.NOTE: For Windows 2008, server R2 and Windows 7, use I nt ernet Explorer 8.8Hit achi AMS 2500 Get t ing St art ed Guide4. I dent i f y your conf i gur at i onThe base unit can be used in a direct - connect point - t o- point or swit ch configurat ion.Fi gur e 1-2: Exampl e of a Di r ect -Connect Conf i gur at i onFi gur e 1-3: Exampl e of a Swi t ch Conf i gurat i onI nst al l i ng t he st or age syst emsThe following sect ions describe how t o inst all your st orage syst em. AMS 2500 st orage syst ems are delivered in a pret est ed configurat ion, wit h t he t rays posit ioned in a cert ain locat ion. When t he sit e t eam inst alls t he st orage syst em, t he t eam should arrange t he t rays as t hey were t est ed ( a piece of paper supplied wit h t he st orage syst ems shows t he t est ed t ray locat ions) . I f t he t rays are not inst alled in t he proper locat ion, t hey generat e HDD ident ificat ion error messages I 6G100 at power up. However, if t he sit e t eam performs an inst allat ion from scrat ch using maint enance mode ( soft reset ) from t he Web, it does not mat t er how t he t rays are arranged.Modular deployment s require configurat ion at t ent ion t o ensure t hat t he st orage infrast ruct ure and ecosyst em component s int eroperat e correct ly wit h Hit achi AMS st orage syst ems and soft ware. There are many component variat ions, and t he Hit achi compat ibilit y and int eroperabilit y mat rix can be used as a reference when const ruct ing configurat ions t hat are support ed end t o end by Hit achi AMS st orage syst ems. To view t he mat rix, please visit : ht t p: / / www. hds. com/ product s/ int eroperabilit y/ ?_p= v.Ser v er s Hi t achi AMS 2500 Base Uni t Management Consol eSer v er s Sw i t chHi t achi AMS 2500 Base Uni tManagement Consol eSw i t ch Ser v er s9Hit achi AMS 2500 Get t ing St art ed Guide5. I nst al l t he base and expansi on uni t sBase and expansion unit s ordered wit h t he Hit achi Global 19- inch rack are delivered preinst alled in t he rack. I f you use a different rack, refer t o and follow all safet y precaut ions in t he document at ion for t he rack.6. At t ach expansi on uni t s ( opt i onal )I f you do not have expansion unit s, skip t o page 11. Ot herwise:a. Connect one expansion unit t o t he base unit : Use a supplied ENC cable t o connect t he PATH# 0 port on cont roller 0 t o t he ENC0 I N port on t he rear of t he expansion unit . Use a supplied ENC cable t o connect t he PATH# 0 port on cont roller 1 t o t he ENC1 I N port on t he rear of t he expansion unit . Gat her t he excess part of t he ENC cable in a circle, t ight en it gent ly and secure, and place it inside t he rack.b. To connect a second expansion unit t o t he base unit : Use a supplied ENC cable t o connect t he PATH# 1 port on cont roller 0 t o t he ENC0 I N port on t he second expansion unit . Use a supplied ENC cable t o connect t he PATH# 1 port on cont roller 1 t o t he ENC1 I N port on t he second expansion unit . Gat her t he excess part of t he ENC cable in a circle, t ight en it gent ly and secure, and place it inside t he rack.c. To connect addit ional expansion unit s, follow t he pat t ern in Figure 1-6 on page 11.CAUTI ON! Observe all safet y guidelines in t he following document s: AMS 2500 St orage Syst em Hardware Guide ( MK- 97DF8007) The document at ion for your rackTo avoid damage t o t he st orage unit or st orage unit component s due t o elect rost at ic discharge ( ESD) , wear an ant i- st at ic wrist st rap when handling t he st orage unit . Connect t he clip t o an unpaint ed part of t he st orage unit chassis frame t o safely channel any st at ic elect ricit y generat ed by your body t o ground. I f no wrist st rap is available, ground yourself by t ouching an unpaint ed part of t he st orage unit chassis frame.10Hit achi AMS 2500 Get t ing St art ed GuideFi gur e 1-4: AMS 2500 Rear PanelFi gur e 1-5: AMS Rear Panel O0O O O OO0O O OO OOOO O O ORKH/RKHE/RKHEDRKEH/RKEHDO OO O O O OO OO O ENC Unit ENC Unit (Modular 2U SAS Expansion Unit)Ca Cb Ca CbLegend:0Fibre Channel connect orOiSCSI connect orOLAN 0 maint enance portOLAN 1 user LAN portOConnect or for UPS cableOPat h 0 ( left ) and Pat h 1 ( right ) - connect t o I N connect or on RKAK/ RKAKS/ RKAKD/RKAKXO Pat h 2 ( left ) and Pat h 3 ( right ) - connect t o I N connect or on RKAK/ RKAKS/ RKAKD/RKAKXOConnect s t o addit ional bat t eryOConnect s t o remot e adapt er ( not on t he RKEH/ RKEHD)CaI N connect or - connect s t o RKH/ RKHE/ RKEH/ RKHED/ RKEHD, RKAK/ RKAKS/ RKAKD/RKAKX UnitCbOUT connect or - connect s t o RKAK/ RKAKS/ RKAKD/ / RKAKX unit11Hit achi AMS 2500 Get t ing St art ed Guided. To connect expansion unit s, use a supplied ENC cable t o connect t he Pat h 0 and Pat h 1 port s on t he rear of t he base unit t o t he I N port on t he rear of each expansion unit .Fi gur e 1-6: Exampl e of Connect i ng Expansi on Uni t s7. Connect cabl es t o t he base uni tEach AMS 2500 cont roller can have one or t wo daught er cards. Bot h cont rollers must have t he same configurat ion. The AMS 2500 syst em can support : 8 Fibre Channel port s 16 Fibre Channel port s 4 iSCSI port s, each 1 Gb 8 iSCSI port s, each 1 GbLegend:0Cont roller # 1O Cont roller # 0OBase unitOExpansion unit s ( ENC0, ENC1)ENC Modul e # 0 ENC Modul e # 10OOO12Hit achi AMS 2500 Get t ing St art ed Guide 4 iSCSI port s, each 10 Gb 8 iSCSI port s, each 10 Gb 8 Fibre Channel port s and 4 iSCSI port s ( each 1 Gb) 8 Fibre Channel port s and 4 iSCSI port s ( each 10 Gb) 4 iSCSI port s ( each 1 GB) and 4 iSCSI port s ( each 10 Gb)To connect cables t o t he base unit :a. Make t he connect ions t o t he rear panel of t he base unit ( see Figure 1- 7) . b. When at t aching a management console t o t he management ( LAN 1) port , connect t he console direct ly t o t he port or use a swit ch or hub.A direct connect ion let s you configure one cont roller at a t ime. Connect ing t hrough a swit ch or hub let s you configure bot h cont rollers using t he same procedure.Fi gur e 1-7: Rear Vi ew of t he Fi bre Channel Hi t achi AMS 2500 Base Uni tTI P: You can at t ach a port able ( pocket ) hub bet ween t he management console and unit t o configure bot h cont rollers in one procedure.Legend:0Bat t ery port ( labeled BATTERY)OPat h 0, 1, 2, and 3 connect ors for connect ing t o expansion unitO FI bre Channel or iSCSI Port sFor Fibre Channel port s, at t ach mult imode fiber- opt ic cablesFor iSCSI port s, at t ach Cat egory 5e or 6 Et hernet cablesOREADY LED ( green)O ALARM LED ( red) . I f t his LED goes ON, refer t o t he User s Guide.OPower recept acle ( bot h power recept acles must be used)OManagement port ( labeled LAN 1)O Maint enance port ( labeled LAN 0) . These port s are for t roubleshoot ing purposes and should not have t o be used.0OO0OO O OOO OOOO OOOO13Hit achi AMS 2500 Get t ing St art ed Guide8. Connect t o a Modul ar 2U SAS Expansi on Uni t ( opt i onal )AMS 2s00 st orage syst ems support connect ion t o a 2U SAS expansion unit . This unit cont ains t wo redundant power supplies, t wo ENC int erface unit s, and from t wo t o 24 small form fact or ( SFF) disk drives. I t can connect t o addit ional expansion unit s or high- densit y expansion unit s. The same expansion unit is used wit h bot h base unit models.Fi gur e 1-8: Fr ont Panel ( Bezel Appl i ed)Tabl e 1-2: Modul ar 2U SAS Expansi on Uni t Fr ont BezelI t em Descr i pt i on0POWER LED ( green) ON = expansion unit is receiving power. OFF = expansion unit is not receiving power.OREADY LED ( green) ON = syst em can be operat ed. Fast blinking = int ernal processing is occurring, syst em is operat ional ( even if t he READY LED blinks) . Slow blinking = offline download processing ended ( occurs during maint enance) .OLOCATE LED ( orange) ON = a failure occurred, but t he expansion unit remains operat ional.0OO14Hit achi AMS 2500 Get t ing St art ed Guide9. Power -up t he base uni ta. Confirm t hat bot h power recept acles on t he rear of t he base unit are connect ed t o working out let s. The green READY LEDs on t he rear panel should be ON and t he green front panel READY LED should blink.b. Press t he Pow er swit ch on t he lower right side of t he front panel of t he base unit t o t he ON posit ion ( see Figure 1- 9 and Figure 1- 10 on page 15) :The base unit performs it s Power On Self Test and t he act ivit y LEDs on t he drives flash and t hen go ON. Aft er a few minut es, t he front panel READY LED goes ON.Fi gur e 1-9: Fr ont Vi ew of Base Uni t ( Fr ont Bezel Removed)NOTE: The out let s should not be cont rolled by a wall swit ch, which can inadvert ent ly remove power form t he st orage unit s.Legend:0Power LED ( green)OFan assemblyOPanel assemblyO Mode swit chO POWER swit chO Alarm ( left ) and Ready ( right ) LEDsALM LED ( red) . I f t his LED goes ON, refer t o t he User s Guide.READY LED ( green)O Bat t ery unitO Alarm LED ( red) . I f t his LED goes ON, refer t o t he User s Guide.O Warning LED ( orange) . I f t his LED goes ON, refer t o t he User s Guide.C Ready LED ( green)0OOOOOOOOO O CO15Hit achi AMS 2500 Get t ing St art ed Guide10. At t ach t he f r ont bezelAt t aching t he front bezel is opt ional. To at t ach it :a. Locat e t he t wo hooks on t he front of t he bezel, one on t he lower right side and one on t he upper right side ( see Figure 1- 10) . I nsert t he hook on t he lower right side of t he bezel int o t he hole on t he bot t om right part of t he base unit . I nsert t he hook on t he upper right side of t he bezel int o t he hole on t he t op right part of t he base unit .b. Aft er t he hooks are engaged, gent ly push t he bezel against t he ball cat ches unt il t he bezel snaps int o place.c. Lock t he bezel by insert ing t he key in t he keyhole and t urning count erclockwise.Fi gur e 1-10: At t achi ng t he Fr ont BezelAt t aching t he front bezel t o t he modular 2U SAS expansion unit is also opt ional. To at t ach it :1. I nsert t he key int o t he keyhole on t he front bezel and unlock t he lock.2. Grasp t he front bezel on bot h sides and above t he cent er of t he unit .3. Engage t he t wo hooks at t he bot t om of t he front bezel int o t he slot s on t he array chassis.4. Push t he front bezel t oward t he chassis t o engage it int o t he ball cat ches.5. Remove t he key from t he front bezel and st ore it in a safe place.NOTE: When t he bezel is removed, t he Pow er swit ch is ident ified on t he enclosure as MAI N SW.Legend:0 Ball cat chesOHook on right sideOMAI N SW ( power) swit chO KeyOHook on left sideOFront bezel0OO OOO16Hit achi AMS 2500 Get t ing St art ed GuideConf i gur i ng t he st or age syst ems11. Set Java Runt i me par amet er s i f necessar yAft er you inst all t he st orage unit s, use t he supplied Navigat or 2 soft ware t o configure t he st orage unit s. I f you int end t o use t he Advanced Set t ings in Navigat or 2 on client s running t he Microsoft Windows, Solaris, or Linux operat ing syst em, download JRE v6. 0 and set t he JRE paramet ers described in t he following sect ions. Ot herwise, Advanced Set t ings will fail, and you will be locked out and unable t o access Advanced Set t ings unt il t he login t imes out ( 20 minut es) . For informat ion about Java updat es, please visit ht t p: / / www. j ava. com/ en/ download/ help/ j ava_updat e. xml.Ot herwise, skip t o St ep 12. I nst all and log in t o Navigat or 2 on page 17.Cl i ent s r unni ng Mi cr osof t Wi ndowsI f your client runs Microsoft Windows, perform t he following procedure:1. Click t he Windows St art menu, point t o Set t i ngs, and click Cont r ol Panel . The Windows Cont rol Panel appears.2. From t he Windows Cont rol Panel, double- click Java Cont r ol Panel . The Java Cont rol Panel appears.3. Click t he Jav a t ab. The Jav a t ab is displayed ( see Figure 1- 11) .Fi gur e 1-11: Java Tab4. Click Vi ew in t he Java Appl et Runt i me Set t i ngs sect ion. The Java Runt ime Set t ings dialog box appears.5. I n t he Jav a Runt i me Par amet er s field, t ype - Xmx 464m.6. Click OK t o exit t he Java Runt ime Set t ings dialog box.17Hit achi AMS 2500 Get t ing St art ed Guide7. Click OK in t he Jav a t ab t o close t he Java Cont rol Panel dialog box.8. Close t he Windows Cont rol Panel.Cl i ent s r unni ng Sol ar i s or Li nuxI f your client runs Solaris or Linux, perform t he following procedure:1. From an XWindows t erminal, execut e t he /bin/jcontrol t o run t he Java Cont rol Panel.2. Click Vi ew in t he Java Appl et Runt i me Set t i ngs sect ion. The Java Runt ime Set t ings dialog box appears.3. I n t he Jav a Runt i me Par amet er s field, t ype - Xmx 464m.4. Click OK t o exit t he Java Runt ime Set t ings dialog box.5. Click OK in t he Jav a t ab t o close t he Java Cont rol Panel dialog box.12. I nst al l and l og i n t o Navi gat or 2The following procedure describes how t o inst all and log in t o Navigat or 2. 1. Find out t he I P address of t he management console ( for example, using ipconfig) . Then change t he consoles I P address t o 192. 168. 0. x where x is a number from 1 t o 254, excluding 16 and 17. Writ e t his I P address on a piece of paper. You will be prompt ed for it during t he Navigat or 2 inst allat ion procedure.2. Disable pop- up blockers in your Web browser. We also recommend t hat you disable ant i- virus soft ware and proxy set t ings on t he management console when inst alling t he Navigat or 2 soft ware.3. I nsert t he Navigat or 2 CD in t he management console CD drive and follow t he inst allat ion wizard. I f t he CD does not aut o- run, double- click t he following file, where nnnn is t he Navigat or 2 version number:\program\hsnm2_win\HSNM2-nnnn-W-GUI.exe The inst allat ion process t akes about 15 minut es t o complet e. During t he inst allat ion, t he progress bar may pause for several seconds. This is normal and does not mean t he inst allat ion has st opped.TI P: For t he best Navigat or 2 experience, we recommend you inst all Navigat or 2 on a new or dedicat ed PC.NOTE: The default I P address for Cont roller 0 management port is 192. 168. 0. 16. The default I P address for Cont roller 1 management port is 192. 168. 0. 17.18Hit achi AMS 2500 Get t ing St art ed Guide4. Aft er t he soft ware is inst alled, launch a browser on t he management console and log in t o Navigat or 2:ht t p: / / < I P address> : 23015/ St orageNavigat orModular/ LoginORht t ps: / / < I P address> : 23016/ St orageNavigat orModular/ Loginwhere < I P address> is t he I P address of t he management console.5. At t he login page, ent er sy st em as t he default User I D and manager as t he default case- sensit ive password. 6. Click t he Logi n but t on and go t o St ep 13. Add st orage syst ems on page 18.13. Add st or age syst emsThe following procedure describes how t o add st orage syst ems. During t his procedure, you ent er t he default Account Aut hent icat ion user I D and password for t he cont roller ( Account Aut hent icat ion is a securit y prot ocol enabled by default on t he AMS) . For more informat ion, refer t o t he St orage Navigat or Modular 2 St orage Feat ures Reference Guide ( MK- 97DF8148) .1. I f t he Arrays page is not displayed, click Ar r ay s in t he Explorer pane ( see Figure 1- 13 on page 20) .2. I n t he Arrays page:a. Look in t he Ar r ay Name column for t he name of t he st orage syst em you want t o configure. Then record t he st orage syst em name in Table 1- 9 on page 45 ( you will refer t o it lat er) .b. Click t he name of t he st orage syst em you want t o configure. The Account Aut hent icat ion Log in page prompt s you for an Account Aut hent icat ion user I D and password ( see Figure 1- 12 on page 19) .NOTE: I f ent ering an I Pv6 address in your Web browser, ent er t he URL in bracket s. Example: ht t p: / / [ xxxx] : 23015/ St orageNavigat orModular/ Login19Hit achi AMS 2500 Get t ing St art ed GuideFi gur e 1-12: Account Aut hent i cat i on Log i n Page3. I n t he Account Aut hent icat ion login page:a. Ent er t he default User I D of r oot in t he User I D field.b. Ent er t he default case- sensit ive password of st or age in t he Passw or d field.c. Click Logi n t o close t he Account Aut hent icat ion Log in page and log in t o Navigat or 2.4. I n t he Arrays page:a. Click t he check box next t o t he st orage syst em you want t o configure.b. Click Add Ar r ay at t he bot t om of t he window t o launch t he Add Array wizard.CAUTI ON! I f y ou change t he Account Aut hent i cat i on passw or d, r ecor d t he new passw or d and k eep i t i n a saf e pl ace. Wi t hout a val i d passw or d, y ou cannot access t he st or age sy st em w i t hout r ei nst al l i ng t he f i r mw ar e. Hi t achi Dat a Sy st ems Techni cal Suppor t cannot r et r i ev e t he passw or d f or y ou. The user I D i s not changeabl e.20Hit achi AMS 2500 Get t ing St art ed GuideFi gur e 1-13: Ar r ays Page5. When t he int roduct ory wizard page appears, click Nex t .6. At t he next page:a. Ent er t he following default I P address in t he Speci f i c I P Addr ess or Ar r ay Name fields for each st orage syst em management port .Cont roller 0: t ype 192. 168.0. 16Cont roller 1: t ype 192. 168.0. 17Check t he St orage Syst em Name Add Array But t onNOTE: I f your management console is direct ly connect ed t o a management port , ent er t he default I P address j ust for t hat port .21Hit achi AMS 2500 Get t ing St art ed GuideFi gur e 1-14: Ent eri ng I P Addresses i n t he Arr ay Wi zardb. I n t he Usi ng Por t s area, select whet her t he port s are secure, nonsecure, or bot h.c. Click Nex t .7. When t he next screen appears:a. Ent er an st orage syst em name in t he Ar r ay Name field.b. Click Nex t .c. Click Fi ni sh and proceed t o St ep 14. Perform t he init ial set up.14. Per f or m t he i ni t i al set upAft er you run t he Add Array wizard, use t he following procedure t o perform t he init ial Navigat or 2 set up. 1. I n t he Arrays page, click t he name of t he st orage syst em you want t o configure.2. I n t he following page, under Common Ar r ay Task s, click I ni t i al Set up.22Hit achi AMS 2500 Get t ing St art ed GuideEnabl e emai l not i f i cat i onsa. I n t he int roduct ory page, click Nex t t o display t he Set up E- mail Alert page.b. I n t he Set up Email Alert page:a. By default , email not ificat ions are disabled. To accept t his set t ing, click Nex t t o display t he Set up Management Port s page and skip t o Configure management port s on page 23.b. To enable email not ificat ions, complet e t he fields in Figure 1- 15 on page 23 ( see Table 1- 3 on page 23) .c. Click Nex t and go t o Configure management port s on page 23.This procedure assumes t hat your SMTP server is set up correct ly t o handle email. I f desired, you can send a t est message t o confirm t hat email not ificat ions will work. For more informat ion, refer t o t he St orage Navigat or Modular 2 Graphical User I nt erface Users Guide ( MK- 99DF8208) and t he Navigat or 2 online help.I nit ial Set up23Hit achi AMS 2500 Get t ing St art ed GuideFi gur e 1-15: Set up Emai l Al er t PageConf i gur e management por t sI n t he Set up Management Port s page:1. Configure t he cont roller management port s manually or aut omat ically ( see Figure 1- 16 on page 24 and Table 1- 4 on page 1- 24) .2. Click Nex t .3. Proceed t o Set up host port s on page 25.Tabl e 1- 3: Enabl i ng Emai l Not i f i cat i onsFi el d Descr i pt i onDisable/ Enable To enable email not ificat ions, click Enable, complet e t he remaining fields, and record your set t ings in Table 1- 9 on page 45.Domain Name Domain appended t o addresses t hat do not cont ain one.Mail Server Address Email address or I P address t hat ident ifies t he base unit as t he source of t he email.From Address Each email sent by t he base unit will be ident ified as being sent from t his address.Send t o Address Up t o 3 individual email addresses or dist ribut ion list s where not ificat ions will be sent or blind copied ( Bcc) .Reply To Address Email address where replies can be sent .24Hit achi AMS 2500 Get t ing St art ed GuideFi gur e 1-16: Set Up Management Por t s PageTabl e 1- 4: Conf i gur i ng Management Por t sFi el d Descr i pt i onI Pv4/ I Pv6 Select t he I P addressing met hod you want t o use.Use DHCP/ Set Manually For I Pv4, Use DHCP configures t he management port aut omat ically, but requires a DHCP server.For I Pv6, Set Aut omat i cal l y configures t he management port aut omat ically.Set Manually Let s you complet e t he remaining fields t o configure t he management port manually. I f you use I Pv6 addresses, not e t hat t hese addresses are based on Et hernet addresses. I f you replace t he st orage syst em, t he I P address is changed. Therefore, you may want t o consider using t he manual set t ing. As you complet e t he set t ings, record t hem in Table 1- 9 on page 45.I f You Sel ect ed t he I Pv4 Pr ot ocol i n t he Set Up Management Por t s Page:I Pv4 Address St at ic I nt ernet Prot ocol address t hat client PCs use t o access t he base unit s management port .I Pv4 Subnet Mask Subnet mask t hat client PCs use t o access t he base unit s management port .I Pv4 Default Gat eway Default gat eway t hat client PCs use t o access t he base unit s management port .Negot iat ion Use t he default ( Aut o) set t ing t o aut o- negot iat e speed and duplex mode, or select a fixed speed and duplex set t ing.25Hit achi AMS 2500 Get t ing St art ed GuideSet up host por t sThe next part of t he wizard let s you configure t he Fibre Channel and iSCSI port s on your st orage syst em. These set t ings are configured on separat e pages wit hin t he wizard. The first page t hat appears let s you configure t he Fibre Channel port s.1. I n t he first Set up Host Port s page, ent er configurat ion informat ion for each Fibre Channel port t hat will be used.I f You Sel ect ed t he I Pv6 Pr ot ocol i n t he Set Up Management Por t s Page:I Pv6 Address St at ic I nt ernet Prot ocol address t hat client PCs use t o access t he base unit s management port .Subnet Prefix Lengt h Subnet prefix lengt h t hat client PCs use t o access t he base unit s management port .I Pv6 Default Gat eway Default gat eway t hat client PCs use t o access t he base unit s management port .Negot iat ion Use t he default ( Aut o) set t ing t o aut o- negot iat e speed and duplex mode, or select a fixed speed and duplex set t ing.Tabl e 1- 4: Conf i gur i ng Management Por t s ( Cont i nued)Fi el d Descr i pt i onI f your: Management console is direct ly connect ed t o a management port on one cont roller, ent er set t ings only for t hat cont roller ( you will configure t he management port set t ings for t he ot her cont roller lat er) . Management console is connect ed using a swit ch or hub, you can ent er set t ings for bot h cont rollers now.26Hit achi AMS 2500 Get t ing St art ed GuideFi gur e 1-17: Set Up Host Por t s Page ( Fi br e Channel Por t s)2. Click Nex t t o display t he following page for configuring t he iSCSI port s. Then ent er configurat ion informat ion for each iSCSI port t hat will be used.Tabl e 1- 5: Conf i gur i ng Fi br e Channel Por t sFi el d Descr i pt i onPort Address Ent er t he address for t he Fibre Channel port .Transfer Rat e Select a fixed dat a t ransfer rat e from t he drop- down list t hat corresponds t o t he maximum t ransfer rat e support ed by t he device connect ed t o t he st orage syst em, such as t he server or swit ch.Topology Select t he t opology in which t he port will part icipat e: Point - t o- Point = port will be used wit h a Fibre Channel swit ch. Loop = port is direct ly connect ed t o t he Fibre Channel port of an HBA inst alled in a server.27Hit achi AMS 2500 Get t ing St art ed GuideFi gur e 1- 18: Set Up Host Port s Page ( i SCSI Port s)3. Click Nex t t o display t he Set up Spare Drive page.Conf i gur e spar e dr i vesThe Set up Spare Drive page shows all t he spares t hat can be used in case one of t he drives fails. I n t his page:1. Select t he drives you want t o use as spares. I f t he drives exceed what can be shown in t he Av ai l abl e Dr i v es area, use t he cont rols at t he t op of t his area t o display ot her pages of drives.Tabl e 1- 6: Conf i gur i ng i SCSI Por t sFi el d Descr i pt i onI P Address Ent er t he I Pv4 address ( dot t ed- decimal not at ion) .Subnet Mask Ent er t he net work subnet mask ( dot t ed- decimal not at ion) .Default Gat eway Ent er t he default rout e.28Hit achi AMS 2500 Get t ing St art ed GuideFi gur e 1-19: Set Up Spar e Dri ve Page2. Aft er checking t he spares you want t o use, click Nex t t o display t he Set up Dat e & Time page.Conf i gur e syst em dat e and t i meI n t he Set up Dat e & Time page in Figure 1- 20 on page 29:1. Select whet her t he dat e and t ime are t o be set aut omat ically, manually, or not at all.2. I f you select Set Manual l y, ent er t he dat e and t ime ( in 24- hour format ) in t he fields provided.3. Click Nex t .29Hit achi AMS 2500 Get t ing St art ed GuideFi gur e 1-20: Set Up Dat e & Ti me PageConf i r mi ng your sel ect i ons1. Review your select ions in t he next five confirmat ion pages:a. I f no changes are required, click Nex t .b. I f you need t o change a select ion, click Back t o ret urn t o t he appropriat e page, make t he desired changes, and t hen click Nex t t o ret urn t he first confirmat ion page and verify t hat t he change was made.c. At t he last confirmat ion page, click Conf i r m t o commit your select ions.2. When t he finish page appears, click Fi ni sh.3. When t he next page t ells you t hat t he init ial set up of t he st orage syst em was complet ed successfully, click Fi ni sh. Change cont r ol l er I P addr esses1. I f t he st orage unit was not added t o your st orage net work:a. Log out of Navigat or 2.b. Power- off t he st orage unit .c. Add t he st orage unit t o t he net work.d. Reconnect t he management console t o t he management port s.e. Rest art your browser and log in t o Navigat or 2 again.NOTE: Configure t he console for t he same subnet on which t he base unit is inst alled. Ot herwise, an error message appears when you t ry t o access Navigat or 2.30Hit achi AMS 2500 Get t ing St art ed Guide2. I f t he Arrays page is not displayed, click Ar r ay s in t he Explorer pane.3. I n t he Arrays page:a. Under t he Ar r ay Name column, check t he st orage syst em name t hat you recorded in Table 1- 9 on page 45.b. Click Edi t Ar r ay. An Edit Array page similar t o t he one in Figure 1-22 on page 31 appears.Fi gur e 1- 21: Li st of Arr ays and Edi t Arr ay But t onCheck an Array Name Here Edit Array But t on31Hit achi AMS 2500 Get t ing St art ed GuideFi gur e 1-22: Exampl e of Edi t Ar r ay Page4. I n t he I P Addr ess or Ar r ay Name of cont r ol l er field, ent er t he same cont roller I P addresses recorded in Table 1- 9 on page 45. Refer t o t he not e on page 25 regarding management consoles direct ly connect ed t o a management port on one cont roller or connect ed using a swit ch or hub.5. Click OK.6. When t he page t ells you t hat t he st orage syst em informat ion has been edit ed successfully, click Cl ose.Sel ect pl at f or m-speci f i c set t i ngsTo connect t o host s running t he following host operat ing syst ems and clust ering solut ions, use Navigat or 2 t o configure t he st orage syst ems host groups and iSCSI t arget s as described in t he following procedures. AI X Apple Macint osh HP- UX Microsoft Windows 2000 Server, Windows Server 2003 and 2008, Windows XP, Vist a Net Ware Red Hat Ent erprise Linux, SUSE Linux Ent erprise, Asianux TruClust er Solaris Verit as Clust er Server VMware32Hit achi AMS 2500 Get t ing St art ed GuideThe following procedure describes how t o select plat form- specific set t ings for Fibre Channel host groups. A host group is a logical ent it y of t wo or more host s t hat share access t o specific disks on t he st orage syst em. The host s in a host group can run t he same or different operat ing syst ems. I n addit ion, t he host s in t he host group usually have special soft ware, such as clust ering soft ware, t o manage virt ual disk sharing and accessibilit y.1. Under t he Ar r ay Name column, check t he st orage syst em name t hat you recorded in Table 1- 9 on page 45 and t hen click t he Edi t Ar r ay but t on ( see Figure 1- 21 on page 30) .2. I n t he cent er pane, click Gr oups. Then, in t he Groups page, click Host Gr oups ( see Figure 1- 23) .Fi gur e 1-23: Gr oups Page3. When t he Host Group page appears ( see Figure 1- 24 on page 33) , check a host group in t he Host Gr oups t ab.Click Groups Click Host Groups33Hit achi AMS 2500 Get t ing St art ed GuideFi gur e 1-24: Host Gr oups Page4. Click Edi t Host Gr oup. The Edit Host Group page appears ( see Figure 1- 25) .Fi gur e 1-25: Edi t Host Gr oup Page34Hit achi AMS 2500 Get t ing St art ed Guide5. Click t he Opt i ons t ab, t hen use t he Pl at f or m pull- down list t o select t he host operat ing syst em t o be connect ed t o t he st orage syst em ( see Table 1- 7, Figure 1- 26, and t he guidelines on page 37) .Fi gur e 1-26: Opt i ons Tab i n t he Edi t Host Gr oup Page6. From t he Mi ddl ew ar e pull- down list on t he Opt i ons t ab, select t he middleware t o be connect ed according t o Table 1- 8.Tabl e 1- 7: Pl at f or m Set t i ngsFor t he Fol l owi ng Oper at i ng Syst ems t o Connect Sel ect Thi s Pl at f or m Set t i ngWindows 2000 Server, Windows Server 2003 and 2008, Windows XP and Vist aWindowsRed Hat Ent erprise Linux, SUSE Linux Ent erprise, AsianuxLinuxSolaris SolarisVMware VMwareHP- UX HP- UXAI X AI XApple Macint osh Not specifiedPlat form Addit ional Set t ingMiddlewareTabl e 1- 8: Pl at f or m Set t i ngsFor t he Fol l owi ng Oper at i ng Syst ems t o Connect Sel ect Thi s Pl at f or m Set t i ngVerit as Clust er Server VCSHP TruClust er Server TruClust erOt her Not specified35Hit achi AMS 2500 Get t ing St art ed Guide7. Click t he OK but t on in t he lower right corner of t he page.8. Click t he Cl ose but t on.You can now perform t he same procedure for iSCSI t arget s. Or you can skip t o Creat e RAI D groups, logical unit s, and host groups on page 38.1. Redisplay t he Groups page and click i SCSI Tar get s ( see Figure 1- 27)Fi gur e 1-27: Gr oups Page2. When t he iSCSI Target s page appears ( see Figure 1- 28 on page 36) , check an iSCSI t arget in t he i SCSI Tar get s t ab.Click Groups Click iSCSI Target s36Hit achi AMS 2500 Get t ing St art ed GuideFi gur e 1-28: i SCSI Tar get s Page3. Click Edi t Tar get . The Edit iSCSI Target page appears ( see Figure 1-29) .Fi gur e 1-29: Edi t i SCSI Tar get Page4. Click t he Opt i ons t ab, t hen use t he Pl at f or m pull- down list t o select t he host operat ing syst em t o be connect ed t o t he st orage syst em ( see Figure 1- 30 on page 37 and Table 1- 7 on page 1- 34) .37Hit achi AMS 2500 Get t ing St art ed GuideFi gur e 1-30: Opt i ons Tab i n t he Edi t Host Gr oup Page5. From t he Mi ddl ew ar e pull- down list on t he Opt i ons t ab, select t he middleware t o be connect ed according t o Table 1- 8 on page 1- 34.Observe t he following guidelines when select ing plat form and middleware set t ings on t he st orage syst em: I f you use winBoot / i by emBoot , I nc. or Open Ent erprise Server by Novell, I nc, check Enabl e NOP- I n Suppr ess Mode. For VMware, select t he following set t ing:Pl at f or m = VMw ar eMi ddl ew ar e = not speci f i edCommon Set t i ngs = St andar d Mode I f you use VMware CHAP ( Discovery session) over an iSCSI connect ion, check Enabl e Di scov er y CHAP Mode and refer t o your VMware document at ion for addit ional informat ion. I f you use alt ernat e pat h ( MPI O: Mult ipat h I / O) and clust ering ( MSCS: Microsoft Clust er Service) configurat ion using t he Microsoft ' s iSCSI Soft ware I nit iat or on Windows Server 2003 wit h t he iSCSI connect ion, t he following set t ing is required. Regist ry set t ing on t he server.When downloading t he iSCSI Soft ware I nit iat or from t he Microsoft home page, refer t o t he descript ions of Microsoft Server Clust er ( MSCS) in t he Microsoft iSCSI I nit iat or 2. x Users Guide, which is a Plat form Addit ional Set t ingMiddleware38Hit achi AMS 2500 Get t ing St art ed Guideseparat e download. Then change t he Regist ry set t ing for Persist ent Reservat ion as required. Exercise care when set t ing t his value. I f set incorrect ly, t he server may not operat e normally. Unique Reserve Mode set t ing on t he st orage syst em.Check Enabl e Uni que Reser ve Mode 1. I f you use an alt ernat e pat h ( MPI O: Mult ipat h I / O) configurat ion on Windows Server 2008, open MPI O on t he Windows Cont rol Panel and regist er HI TACHI DF600F as an MPI O device. I f connect ing wit h a Tru64 host , select Not speci f i ed from t he Pl at f or m drop- down list . Do not select HP- UX for Tru64.6. Click t he OK but t on in t he lower right corner of t he page.7. Click t he Cl ose but t on.8. Go t o Creat e RAI D groups, logical unit s, and host groups on page 38.Cr eat e RAI D gr oups, l ogi cal uni t s, and host gr oupsThe following sect ions describe how t o creat e RAI D groups, logical unit s, and host groups. For addit ional informat ion, refer t o t he Navigat or 2 online help.1. I f t he Common Array Tasks area is not displayed, click t he st orage syst em under t he Ar r ay Name column in t he Arrays page.2. I n t he Common Array Tasks area, click Cr eat e Logi cal Uni t and Mappi ng. The Creat e & Map New Volume wizard st art s.NOTE: Di scover y CHAP Mode is not used wit h Fibre Channel, even if t his opt ion appears t o be select able and checked.NOTE: I f LUN Manager is not inst alled or enabled in t he st orage syst em, or if host group securit y is disabled or host group assignment is skipped, a screen appears at t he end of t his procedure t o inform you t hat Navigat or 2 aut omat ically assigns logical unit s t o all host s connect ed t o t he select ed port .39Hit achi AMS 2500 Get t ing St art ed Guide3. When t he int roduct ory page appears, click Nex t . The page in Figure 1-31 appears.Fi gur e 1-31: Cr eat e or Sel ect RAI D Gr oup/ DP Pool Page4. Creat e a new RAI D group or use ones t hat already exist :To creat e a new RAI D group:a. Select Cr eat e a new RAI D gr oup if it is not select ed.b. Use t he drop- down list s t o select a drive t ype, RAI D level, and dat a + parit y ( D+ P) combinat ion for t he RAI D group.Creat e Logical Unit and Mapping40Hit achi AMS 2500 Get t ing St art ed GuideTo use RAI D groups t hat already exist :a. Select Use an ex i st i ng RAI D gr oup.b. Select a RAI D group from t he drop- down list .5. This page also let s you configure new or exist ing Dynamic Provisioning ( DP) pools if you inst alled t he license key for Hit achi Dynamic Provisioning. For more informat ion, refer t o t he Hit achi AMS 2000 Family Dynamic Provisioning Configurat ion Guide ( MK- 09DF8201) .6. Click Nex t . The page in Figure 1- 32 appears.Fi gur e 1-32: Creat e or Sel ect Logi cal Uni t s Page7. Creat e new logical unit s or use ones t hat already exist , check Cr eat e a new l ogi cal uni t s. Then check t he appropriat e opt ion below:To creat e new logical unit s, select one of t he following opt ions: Cr eat e many l ogi cal uni t s let s you creat e mult iple logical unit s whose size and number you specify in t he Logi cal Uni t Capaci t y and Number of Logi cal Uni t s fields. Each logical unit t hat will be creat ed will be t he same size t hat you specify in t his field.OR To creat e a single logical unit consist ing of t he maximum available free space in t he select ed RAI D group, click Cr eat e one l ogi cal uni t t o assi gn t he l ar gest r egi on of avai l abl e f r ee space.OR To creat e a single logical unit consist ing of all t he available free space, click Cr eat e one l ogi cal uni t t o assi gn al l of t he avai l abl e f r ee space i n t he sel ect ed RAI D gr oup.To use logical unit s t hat already exist : Under Ex i st i ng l ogi cal uni t s, check each exist ing logical unit you want t o use. To check t hem all, click t he check box t o t he left of LUN. ( Clicking t his check box again deselect s all exist ing logical unit s. )41Hit achi AMS 2500 Get t ing St art ed Guide8. Click Nex t . A page similar t o t he one in Figure 1- 33 appears.Fi gur e 1-33: Cr eat e or Sel ect Host Gr oup/ i SCSI Tar get Page9. Select t he physical port for t he host group.10. Creat e new host groups or use ones t hat already exist :To creat e new host groups:a. Click Assi gn now if it is not select ed.b. Select Cr eat e a new host gr oup.c. I n t he Host Gr oup No field, ent er a host group number from 1 t o 127.d. I n t he Name field, ent er a host group name from 1 t o 32 charact ers.e. Select a Pl at f or m or Mi ddl ew ar e set t ing, or bot h, if appropriat e for your configurat ion ( refer t o t he Navigat or 2 online help) .To use host groups t hat have already been creat ed:a. Select Use an ex i st i ng host gr oup.b. Use t he Host Gr oup drop- down list t o select a host group.11. Click Nex t . The Connect t o Host s page appears ( see Figure 1- 34 on page 42) .42Hit achi AMS 2500 Get t ing St art ed GuideFi gur e 1-34: Connect t o Host s Page12. Check all of t he host s t o which you want t he st orage syst em t o connect . 13. When you finish, click Nex t .14. Review your select ions in t he next t wo confirmat ion pages: I f no changes are required, click Nex t . I f you need t o change a select ion, click Back t o ret urn t o t he appropriat e page, make t he desired changes, and t hen click Nex t t o ret urn t he first confirmat ion page and verify t hat t he change was made. At t he last confirmat ion page, click Conf i r m t o commit your select ions.15. The next page confirms t hat t he Creat e & Map Volume Wizard complet ed successfully. To creat e addit ional RAI D groups, logical unit s, and host groups, click Cr eat e & Map Mor e LU and repeat t his procedure. Ot herwise, click Fi ni sh.15. Add t he newl y conf i gur ed st or age syst em t o Navi gat or 2Aft er you configure bot h cont rollers, perform t he following procedure t o add t he newly configured st orage syst em t o Navigat or 2.1. I f t he Arrays page is not displayed, click Ar r ay s in t he left pane.2. From t he Arrays page, check t he st orage syst em you j ust configured under t he Ar r ay Name column.3. Click Remove Ar r ay t o remove t he select ed base unit from t he Arrays area.4. When t he message indicat es t hat t he base unit was removed successfully, click Cl ose t o remove t he message.43Hit achi AMS 2500 Get t ing St art ed Guide5. I n t he Arrays page:a. Click Add Ar r ay t o run t he Array wizard.b. Click Nex t at t he first page.6. When t he Search Array page appears ( see Figure 1- 35) , ent er t he I P address for each cont roller, which you recorded in Table 1- 9 on page 1-45.Fi gur e 1-35: Sear ch Arr ay Page7. Click Nex t and Fi ni sh t o complet e t he wizard. The newly configured base unit appears in t he Arrays area.Compl et e your i nst al l at i onTo complet e t he configurat ion procedure, perform t he following configurat ion t asks based on your st orage and environment al requirement s ( for det ails, see t he Navigat or 2 online help) : Creat e, format , delet e, and filt er logical unit s Creat e, edit , init ialize, delet e, and filt er t arget s Back up volumes t o prevent dat a loss Perform local replicat ion t asks ( creat e, edit , split , resync, rest ore, and delet e pairs) Enable license keys for any st orage feat ures t hat require t hemTI P: Alt ernat ively, if you have many cont rollers, you can click Range of I P Addr esses and ent er t he st art ing and ending I P address range in t he Fr om and To fields, respect ively.44Hit achi AMS 2500 Get t ing St art ed GuideAddi t i onal i nf or mat i onUser r egi st r at i on Refer t o t he Hit achi Web Port al:ht t ps: / / port al. hds. com/ index. php/ component / regist rat ion/ st artPr oduct document at i on Refer t o t he supplied document at ion CD or visit t he Hit achi Web Port al:ht t p: / / www. hds. com/ corporat e/ resources/Pr oduct I nt er oper abi l i t yRefer t o t he int eroperabilit y mat rix at :ht t p: / / www. hds. com/ product s/ int eroperabilit y/Fi r mwar e ( mi cr ocode)Refer t o t he Navigat or 2 online help and t o t he Hit achi Web Port al:support . hds. comTr oubl eshoot i ngRefer t o t he Hit achi Support page:ht t p: / / www. hds. com/ support /Gl obal Ser vi cesHit achi Dat a Syst ems Global Services can increase t he value of I T t o your business wit h carefully applied new t echnologies for reducing risk, accelerat ing ROI , lowering cost s, and managing your st orage infrast ruct ure successfully.ht t p: / / www. hds. com/ services/Hi t achi Dat a Syst ems St or age For umsHit achi Dat a Syst ems Forums let you exchange informat ion and quest ions comment s about Hit achi Dat a Syst ems product s, services, and support . ht t p: / / forums. hds. comNOTE: I f you encount er a problem regist ering your st orage syst em, please visit ht t p: / / www. hds. com/ solut ions/ smb/ .45Hit achi AMS 2500 Get t ing St art ed GuideRecor d conf i gur at i on set t i ngsWe recommend t hat you make a copy of t he following t able and record your configurat ion set t ings for fut ure reference.Tabl e 1- 9: Recor di ng Conf i gur at i on Set t i ngsFi el d Descr i pt i onSt orage Syst em NameEmai l Not i f i cat i onsEmail Not ificat ions O DisabledO Enabled ( record your set t ings below)Domain NameMail Server AddressFrom AddressSend t o AddressAddress 1:Address 2:Address 3:Reply To AddressManagement Por t Set t i ngsCont roller 0Configurat ion O Aut omat ic ( Use DHCP)O Manual ( record your set t ings below)I P AddressSubnet MaskDefault Gat ewayCont roller 1Configurat ion O Aut omat ic ( Use DHCP)O Manual ( record your set t ings below)I P AddressSubnet MaskDefault Gat ewayHost Por t Set t i ngsFibre Channel Port : ______ Port Address:Transfer Rat e:Topology:Fibre Channel Port : ______ Port Address:Transfer Rat e:Topology:Fibre Channel Port : ______ Port Address:Transfer Rat e:Topology:46Hit achi AMS 2500 Get t ing St art ed GuideFibre Channel Port : ______ Port Address:Transfer Rat e:Topology:Fibre Channel Port : ______ Port Address:Transfer Rat e:Topology:Fibre Channel Port : ______ Port Address:Transfer Rat e:Topology:Fibre Channel Port : ______ Port Address:Transfer Rat e:Topology:Fibre Channel Port : ______ Port Address:Transfer Rat e:Topology:iSCSI Port : ___________ I P Address:Subnet Mask:Default Gat eway:iSCSI Port : ___________ I P Address:Subnet Mask:Default Gat eway:iSCSI Port : ___________ I P Address:Subnet Mask:Default Gat eway:iSCSI Port : ___________ I P Address:Subnet Mask:Default Gat eway:LUN Set t i ngsRAI D GroupFree SpaceLUNCapacit ySt ripe SizeFormat t he Logical Unit O YesO NoTabl e 1- 9: Recor di ng Conf i gur at i on Set t i ngs ( Cont i nued) Fi el d Descr i pt i on1Hit achi AMS 2500 Getting Started GuideMK-97DF8032EN-13Hi t achi Dat a Sy st emsCor por at e Headquar t er s750 Cent ral ExpresswaySant a Clara, California 95050- 2627U. S. A.Phone: + 1 408 970 1000www. hds. cominfo@hds. comAsi a Paci f i c and Amer i cas750 Cent ral ExpresswaySant a Clara, California 95050- 2627U. S. A.Phone: + 1 408 970 1000info@hds. comEur ope Headquar t er sSeft on ParkSt oke PogesBuckinghamshire SL2 4HDUnit ed KingdomPhone: + 44 ( 0) 1753 618000info. eu@hds. com