standard inclinometer casing
TRANSCRIPT
For Further InFormatIon Please ContaCt: Soil Instruments Limited, Bell Lane, Uckfield, East Sussex, TN22 1QL, United KingdomTel: +44(0)1825 765044 Fax: +44(0)1825 761740 Web: www.soil.co.uk Enquiries: [email protected]
Standard Inclinometer Casing
DATASHEET C18P
art o
f the
gro
up
Features Manufactured from ABS plastic which is flexible, impact and
corrosion resistant thus ensuring long service life
Precision extruded keyway ensures low spiral and perfect fit for the inclinometer probe wheels rendering accurate inclinometer and IPI data
Special couplings at joints safeguard against ingress of water or grout
Offered in two sizes of 70mm and 85mm OD with ±75mm telescopic sections for accommodating high settlement or heave
Simple installation
Technical Applications
Standard Casing is a specially manufactured ABS extrusion with precise keyways formed at 90° into the internal face. The keyways allow for the accurate placing and orientation of inclinometer probes or In-Place Inclinometer Sensors (IPI’s).
It is joined using rivets, glue and tape to seal against water or grout ingress. Both standard and telescoping couplings are available along with a range of bottom and top cap assemblies. Standard casing is supplied in both 70mm and 85mm outside diameters and is suitable for most construction and civil engineering projects. It can be used in boreholes, embedded in fill material, cast into concrete or attached to structures.
It is designed to deflect with the ground, materials or structural movement and provide inclination information over an extended period of time. (Its useful life only ends when the movement of the material or structure causes the casing to shear or prevents the inclinometer probe from passing down the full length of the installation).
Inclinometer systems provide data for:
site investigation
Evaluating the soil strength and stability
Verification of design assumptions
Installed in structures Standard Casing can confirm initial design assumptions by proving actual movement compared to design predictions
long term monitoring
Long term monitoring of structures and ground conditions to establish changes after works have finished
standard casing and inclinometers are suitable for the following applications:
slopes and landslides - Inclinometer tube is installed to determine the shear and slip zones and whether shear is planar or circular. Correct installation will determine if the movement is constant, slowing or accelerating.
Diaphragm or sheet pile walls - Inclinometer systems can be used to ascertain the stability of the retaining wall and check that deflections are within design assumptions. The system should also show ground movement that could affect other buildings and can verify the performance of struts and ground anchors.
Dams - Can be used to detect movement in the downstream and upstream side of the dam and define shear zones infoundations. Inclinometer systems can also monitor deformation of concrete face dams and will determine shear,depth, direction, magnitude, and rate of movement (i.e. constant, accelerating, or decelerating).
tunnels - Detect and record soil movement due to tunnelling operations. Verify design assumptions and element analysis.
retaining walls - Measure bending and rotation in the retaining wall.
laterally loaded piles - Monitor bending of piles. Standard Casing has been extensively tested to ensure that the coupling joint is strong and resists the ingress of water and grout.
Key Benefits
standard Inclinometer Casing is an integral part of inclinometer and IPI sensor systems. used for measurement of lateral and vertical movements of soil, rock and structures and is typically installed in boreholes
Its versatility renders it suitable for use in landfills, cast to concrete or attached to structures
Designed to deflect with the ground, materials or structural movement and provide inclination information over a long period of time
economical casing assembled using couplings, rivets and sealing tape, ensuring strong joints
Soil Instruments Ltd has an ongoing policy of design review and reserves the right to amend these specifications without notice.Revision No: 01.5 / Issue Date: 19/02/2009
Standard Inclinometer Casing
DATASHEET C18P
art o
f the
gro
up
Specifications
Ordering Information
CasInG sPeCIFICatIons 70mm oD 85mm oD
Material ABS (Acrylonitrile Butadiene Styrene) ABS (Acrylonitrile Butadiene Styrene)
Groove spiral < 0.3° / 3m < 0.3° / 3m
Collapse rating 1960kPa 1770kPa
Bend rating 3.07kN 2.65kN
Maximum temperature 80°C 80°C
Tensile strength 705kgF 700kgF
Torque 520Nm 481Nm
CasInG DImensIons
Length 3m 3m
Outside diameter 70mm 85mm
Inside diameter 62mm 77mm
stanDarD CouPlInG DImensIons
Length 160mm 200mm
Outside diameter 77mm 91mm
Inside diameter 70mm 85mm
telesCoPInG CouPlInG DImensIons
Length 400mm 380mm
Telescoping range ±75mm ±75mm
Outside diameter 77mm 91mm
Inside diameter 70mm 85mm
WeIGhts
Casing 2.66kg 3.18kg
End cap 70g 90g
Top cap 48g 64g
Lockable top cap 554g 654g
Telescoping coupling 400g 380g
Standard coupling 136g 236g
Lockable top cap
Casing
Telescopingsection
Bottom cap
Externalspline
Standardcoupling
Rivets
Part no. DesCrIPtIon
stanDarD InClInometer CasInG - 70mm oD
C18-70.1 Ø70mm Inclinometer Casing, 3m long
C18-70.2 Coupling, Ø77mm, 160mm length
C18-70.4 Bottom cap
C18-70.5 Telescoping coupling, 77mm OD, 400mm length, 75mm range
C18-70.6 Lockable top cap assembly
C9-1.4 Top Cap
stanDarD InClInometer CasInG - 85mm oD
C18-85.1 Ø85mm Inclinometer Casing, 3m long
C18-85.2 Coupling, 91mm OD, 200mm length
C18-85.3 Telescoping coupling, 91mm OD, 400mm length, 75mm range
C18-85.4 Bottom cap
C18-85.5 Top cap
InstallatIon eQuIPment
C9-3.1 Riveting kit (includes; hand drill, 3.3Mm drill, rivets and rivet tool)
C9-3.2 Rivets (per 1000) for standard couplings (4 rivets required per coupling)
C9-3.3 Rivets (per 1000) for telescoping couplings (4 rivets required per coupling)
W6-4.3 Sealing tape (1 roll per 6 couplings)
C9-3.4 Sealing mastic (1 tube per 20 couplings)
C9-3.5 Mastic gun
W6-1.2 Bentonite powder (per 25 kg)
C9-3.6 Security cover
C9-3.7 Lockable heavy duty stopcock cover
C9-3.8.1 Tube support plate for 70mm casing
C9-3.8.2 Tube support plate for 85mm casing
C9-3.9 Drill for rivets, 4.2Mm diameter