SS21T Quick Guide【 English 】Jumper Settings

Mainboard illustration

B1. AC Power Switch

B2. AC Power Socket

B3. Line-In Port

B4. Line-Out Port

B5. Microphone Port

B6. LAN Port

B7. USB Ports

B8. VGA Port

B9. COM Port

B10. PS/2 Mouse Port

B11. PS/2 Keyboard Port

SPDIF-IN/Out Connector

Pin Assignments:1=SPDIF IN 2=GND3=VCC 4=GND5=VCC 6=SPDIF OUT

Fan Connectors

Pin Assignments:1=HD LED_P 2=PWR SLP3=HD LED_N 4=PWR SLP 5=RST SW N 6=PWR SW P 7=RST SW P 8=PWR SW N9=RSVD 10=KEY

Front Panel Connector

Extended USB Connectors

Pin Assignments (USB3,4):

1=GND 2=GND

3=USB+ 4=USB-

5=5VSB

Pin Assignments (JP11):

1=USBPWR0 2=USBPWR1 3=USB_FP_P0- 4=USB_FP_P1-5=USB_FP_P0+ 6=USB_FP_P1+7=GND 8=GND9=KEY 10=USB_FP_OC0

Parallel Port Header-EXT. Printer Port

A. Begin Installation

1. Unscrew 5 screws of the chassis cover.

2. Slide the cover backwards and upwards.

3. Remove the front panel.

B. CPU and FAN Installation

Note: For safety reasons, please ensure that the power cord is disconnected before opening the case.

1. Unlock the DIMM latch.

2. Align the DDR2 module’s cutout with the DIMM slot notch. Slide the DDR2 module into the DIMM slot.

C. DDR2 Installation

3. Check that the latches are closed, and the DDR2 modules are firmly installed.

D. Card Reader and HDD Installation

6. Plug the Serial ATA HDD cable in the SATA1 header and connect the power extension cable to the 4-pin powerheader as shown.

1. Place the HDD/Card Reader in the rack and secure with screws from the side.

E. Optical Drive Installation

2. Connect the card reader USB cable to the Card Reader.

3. Connect the Serial ATA, power extension cables to the HDD.

1. Slide the optical drive into the chassis.

4. Place the rack in the chassis and refasten the rack.

3. Plug the optical drive cable and power cable into the optical drive.

1. Unfasten expansion slot bracket screws. Remove the back panel bracket and put the bracket aside.

F. Accessories Installation

2. Install the PCI/PCI Express x16 card into the PCI/PCI Express x16 slot.

2. Replace the cover and refasten 5 screws.

G. Complete

3. Complete.

F1

F3

F1. 5.25” Bay

F2. Eject Button

F3. 3.5” Bay

F4. HDD LED

F5. Power Switch & LED

F6. Mic in

F7. Headphone

F8. USB Ports

3. Secure the bracket.

Note: Please load the optimized BIOS values.

1

2

Cutout

Latch Latch

Notch

Front panel

Back panel

AUX-IN Connector

Pin Assignments:1=AUX-IN LEFT2=Ground3=Ground4=AUX-IN Right

Pin Assignments:

1=PSTB 2=PD0 3=PD1 4=PD25=PD3 6=PD4 7=PD5 8=PD69=PD7 10=P_-ACK 11=P_BUSY 12=P_PE13=P_SLCT 14=PAUTOFD 15=P_-ERR 16=PINIT17=PSLCTIN 18=GND 19=GND 20=GND21=GND 22=GND 23=GND 24=GND25=GND 26=KEY

Socket AM2 (940PIN)

Two 240 pins DDR2 DIMM Slots

Front Panel Connector- JP7

Floppy Connector- FDD1One IDE Slot- IDE1

USB Headers- USB3,USB4

AUX-IN Connector- CN11

Line-In/Line-Out/Microphone Ports

LAN & Dual USB Ports

ATX Power Connector- CN12

One PCI Express x16 Slot

One PCI Slot

ITE 8716F-S Chipset

Serial ATA- SATA1,2

Dual USB Ports

SiS 761GX Chipset

SPDIF-In/Out Connector- JP8 EXT. PRINT PORT- JP5

VGA Port

PS/2 K/B & M/S Ports

Note: Repeat to install additional DDR2 modules if desired.

5. Unscrew 5 screws of the 3.5” bay rack mount and remove the rack.

FAN Connector- FAN1

12345

F1F2

F8F7

F4

F6

F5

B1 B2

B4

B3 B5

B6 B7

B8

B9

B11B10

4. Use a screwdriver to take apart of the 5.25” Bay Cover.

FAN Connector- FAN2 ATX Power Connector- PWR1

USB Header- JP11

SiS 966L Chipset

COM Port

HLED

RST

PWR LED

PWON

GLED

Clear CMOS Header

JP7

CN11

4 3 2 1

JP8

Pin Assignments:1=AUD MIC 2=AUD GND3=MIC BIAS 4=AUD VCC 5=AUD_F_R 6=AUD_RET_R 7=REVD 8=KEY9=AUD_F_L 10=AUD_RET_L

Real Audio Connector

JP5

1 2 3 4 5 6 7 8 9 10 11 12 13

14 15 16 17 18 19 20 21 22 23 24 25 26

USB3,USB4

97531

108642

JP11

5. Screw the FAN to the mainboard and connect the fan connector.

Note: Please refer to the user guide of the fan you bought to install the fan.

5. Plug card reader USB cable in the USB header.

2. Fasten the side screws.

1. Re-attach the front panel.

Fan Connector

Power Extension Cable

Card Reader USB Cable

Serial ATA Cable

Power Extension Cable

Optical Drive Cable Optical Drive Power Cable

Note: You may install two 5.25” equipment on this machine.

PCI Express x16 slot

PCI slot

FAN Connector- FAN3

Clear CMOS- JP12Audio Connector- JP9

COM Port- COM2

1. Pull up the CPU socket lever to 90-degrees.

2. Match the yellow triangle on a corner of the CPU with the triangle on the socket corner and gently insert the CPU into the socket.

3. Press down the CPU socket lever.

Note: Failure to correctly align the CPU and socket can result in damage to the CPU.

Note: Please do not use too much Heatsink compound.

C2001AMD

ASSEMBLED IN MALAYSIA

LOTES SOCKET AM2 LOTES SOCKET AM2

AMD AthlonTM

64 X2 Processor

Triangle Markings

LeverLever

4. Spread an even layer of heatsink compound on the CPU die.

SPEED_SENSE

FAN1/ FAN2

PWM_CRTL +12V GND

1

FAN3

SPEED_SENSE +12V GND

1

Pin1-2 (Default) Pin2-3 (Clear CMOS)

JP12 JP12

1 2 3 4 5 6

JP9

9 7 5 3 1

8 6 4 210

Pin Assignments:1=DCD 2=RxD3=TxD 4=DTR5=Ground 6=DSR7=RTS 8=CTS9=RI

COM Port

COM2

1 3 5 7 9

2 4 6 8