spreader bar end cap assembly (ac25c) · b30.20 & aws d14.1 testing also conforms to osha 2232....

To avoid lifter failure, potential death and property damage, never exceed WLL (Working Load Limit).

This document contains the proprietary information of Tandemloc, Inc. and your access and use shall be, and is at all times, pursuant to and limited by the Tandemloc, Inc. Terms of Use.

You shall not , and shall not encourage, assist, or authorize another party to copy, distribute, publicly display, modify, reverse engineer, decompile, or take any other action to reproduce this document or the information

contained herein. © Copyright 2014 by Tandemloc, Inc.

Dimensions are subject to manufacturing tolerance and change.

Tandemloc, Inc. designs, manufactures and tests lifting, securing and mobilizing components for all

industries. See our website for details and important safety information.

Read all safety labels and instructions prior to use. Product to be used by qualified personnel only.

Email: [email protected] • www.tandemloc.com

824 Highway 101 • Havelock, NC 28532

Tel: 1.800.258.7324 (252.447.7155)

FAX 1.800.892.3273 (252.447.5502)

SPREADER BAR END CAP ASSEMBLY (AC25C)

Cage Code: 65059 | Drawing No: SAC25C | Revision: AZ | Sheet: 1 of 4

UNLESS OTHERWISE SP ECIFIED, DIMENSIONS ARE IN INCHES

NOTES:

1. DESIGNED & CONSTRUCTED TO CONFORM TO ASME

B30.20 & AWS D14.1 TESTING ALSO CONFORMS TO

OSHA 2232. DESIGN CATEGORY A.

2. MATERIAL IS STEEL, PAINTED YELLOW.

3. ASSEMBLIES ARE PROOF TESTED & CERTIFIED FOR

THE LOADS SHOWN IN THE CHART ON SHEET 2.

4. USE TWO END CAPS, ONE ON EACH END OF

SPREADER PIPE FOR A CAPACITY OF 2X THE

END CAP WLL.

5. USE MANUAL #SAC25C, INCLUDED WITH EACH SET

OF PIPE CAPS.

6. SEE SHEETS 2, 3 & 4 FOR OTHER DATA

7. BECAUSE OF DIMENSIONAL MODIFICATIONS, THE

END CAPS MADE AFTER 05/31/03 MAY NOT PROVIDE

THE SPAN OR HAVE SAFETY PIN HOLE ALIGNMENT

WITH SPREADER PIPES MADE TO SAC22P DIMENSIONS

PRIOR TO 05/31/03. END CAPS ARE AVAILABLE

TO FIT THOSE CONDITIONS. CONTACT YOUR

TANDEMLOC ACCOUNT MGR FOR INFORMATION.

8. EACH END CAP HAS A LABEL WITH DATA AS SHOWN

BELOW AND THE NOMINAL PIPE SIZE IT FITS. LABEL

MAY SAY "SCHED 60 WALL" INSTEAD OF "SCHED 80

WALL" DEPENDING ON SIZE OF END CAP.

9. EACH END CAP OVER 8" HAS ONE OR TWO

D-RINGS FOR LIFTING THE END CAP ONLY.











Tel: 1.800.258.7324 (252.447.7155)

FAX 1.800.892.3273 (252.447.5502)




NOTE:

THE ORDER NUMBERS IN THE ABOVE LEFT HAND COLUMN ARE

TO ORDER END EYE CAPS FOR STANDARD SERVICE TEMPERATURE PER

TANDEMLOC STANDARD #EAD21000A.

SEE SHEET 1, 3 & 4 FOR OTHER DATA.

NOTE:

TO ORDER LOW TEMPERATURE ARCTIC TYPE LIFT GEAR ALSO PER

TANDEMLOC STANDARD #EAD21000A, ADD PREFIX "L" TO THE ABOVE

NOTED STANDARD NUMBER. FOR EXAMPLE, AC25C-045089EH

STANDARD ORDER NO. BECOMES LAC25C-045O89EH ARCTIC

ORDER NO.

U.S. PATENT # 7,967,352

CANADIAN PATENT # 2,639,127

CANADIAN PATENT # 2,869,062











Tel: 1.800.258.7324 (252.447.7155)

FAX 1.800.892.3273 (252.447.5502)




spreader bar end cap assembly (ac25c) · b30.20 & aws d14.1 testing also conforms to osha 2232....

Documents