spraymet valve industry ppt
TRANSCRIPT
Coatings for the severe service Industry :
Ball valve, Plug Valve, Gate valve,
control valve and Pumps
SPRAYMET SURFACE TECHNOLOGIES Pvt Ltd
Bangalore : A 413, 9th main, 2nd stage,Peenya Indl area ,Bangalore
5600058 [email protected] , Tel : 080-28364565 mobile : 9886116400
Pune Unit : T 180, T Block, MIDC, Bhosari, Pune 411026
[email protected], Tel 8149046272
1
SPRAYMET
SURFACE TECHNOLOGIES
SPRAYMET
SPRAYMET
1
5Schematic o f thermal spray coating
Heat source, spray gun
Acceleration Impacting Spreadening and cooling
Feedstock materials
Stick
Wire
Powder
>200 alloys * Upto 15000 deg C * Upto mach 2.5 * Bond > 10000PSI
Thermal energy vs. kinetic energy
in thermal spray
3
Ther
mal
Ener
gy
Kinetic Energy >>>> BOND strength >>>
Elect ARC
Plasma
HVOF
CS
Wirearc Spray 5000 deg C
Plasma Spray 15000 dec C
High velocity oxy fuel
Cold Spray
Melt or partially melt
Solid
SPRAYMET
200m/sec1200mts/sec
High energy Hi velocity Plasma HE
Plasma
600mts/sec
HVAFHigh velocity AIR fuel
1960 1980 2005
Process Flow
SPRAYMET
How coating bonds?
Plasma spraying
6
• plasma temperature: up to 30000 ºC.
• virtually all existing materials.
High-velocity oxy fuel spraying (HVOF)
7
• gas temperature: 3000 ºC;
• sprayed materials: virtually all existing
materials, in practice mostly carbide/metal
and carbide / self-fluxing alloy mixtures.
HVOF – Exclusive process for carbides
8
Plasma transfered arc spraying (PTA)
9
• Fe, Ni, Co, Cr based alloys,
stainless steels, cermets
Laser cladding
10
• virtually all metal alloys, cermets and
ceramics.
Coatings’ properties
Adhesion and porosity
Spray technology Velocity, m/s Porosity, % Adhesion, MPa
Flame spraying
• powder
• wire
30
180
6 – 15 17 – 70
15 – 20
Arc spraying 240 2 – 8 40
Plasma spraying (different
modifications)
240 – 1200 < (0,5 – 2) 20 – 70
Detonation gun spraying 910 < 1 ≥ 100
HVOF, HVAF 610 – 1500 < 0,5 65 – 90
Cold spraying 500 – 1200 1 – 3 60 – 100
11
Process and prosperities
comparison
Adhesion
Strength
(Mpa)
Processes Particle speed
m/s (km/h)Spray rate
kg/hPorosity Levels
%
Thickness capablity
mm
Flame Temp °C
Powder Flame 70 (144) 1...8 10...15 0,2...5 3000 10...30
Wire Flame 70 (144) 5...8 0,2...0,4 0,2...5 3000+1100 n. 300
Arc Spray 220 (790) 6...40 10...20 0,2...10 3000 10...30
Plasma 600 (2160) 1...6 2...8 0,2...2 16500 20...70
HVOF 800 (2880) 2...9 0,5...2 0,2...2 2800 60...120*
HVAF 800 (2880) 10...30 0,1...1,5 0,1...1.5 1800 60...120*
Detonation 900 (3240) 2...6 0,1...1,5 0,1...0.50 4500 75...120*
Characteristics of thermally sprayed coating structures(Typical Expected values)
As sprayed (3-5Ra)
Oxide-(max 3%) Cracks-(Not allowed) Pores(1-2%)
t
Grit blasted surface3-6 Ra
Unmolten particle3 % maxEmbedded grit blasting
pieces-10% or area max
“over-blasted”
area
HVAF sprayed WC-10Co-4Cr Coating
15
HVOF carbide hardness
16
ASTM G 65 abrasion test
17
Coating Capabilities and Range
18
BALL COATING, GRINDING AND LAPPING CAPABILITIES :
Robotic HVOF : Fanuc Robot and Praxair JP5000HVOF with Ball holding fixtures for Lathe rotation or Turn table rotation. Ball Grinding : Upto 24 “ SPM with diamond grinding segments Ball Lapping : Upto 8” full diameter Lapping with matching eat 8”-16” : Seal area Lapping with matching seat Testing : NDT (on Ball), HV(0.3),Bond test, Bend Test (on Cuopons) Leak Test : Ball and seat will be tested for leak with ethanol in ball and seat pocket and 2 Bar air pressure from bottom SPRAYMET Coating selection guide for METAL SEATED BALL VALVE
Coating Hardness Hv 0.3 typical
Typical Wear factor
Corrosion factor
Temp resistance
Coting method
Typical finish thickness
Application area
1
Tungsten carbide
1100Hv ( Rc 70)
5 2 Upto 400 deg C
HVOF 150-200 microns
most widely used in non corrosive atm.
2
Chromium carbide
850 HV (Rc 65)
4 4 Upto 850 deg C
HVOF 200-300 Used where wet corrosion is present : Steam, ammonia etc Default coating in unknown condition.
3 NiCrBSi ( colmonoy6)
58 Rc 3 4 Upto 650 deg C
HVOF 200-300 Corrosion and temp conditions . Power stations, ash handling. Low cost to carbide
4 Stellite 6 + other stellitegrades1,12,21
42 RC 3 5 Upto 650 HVOF 200-300 Widely used where corrosion and temp are present . Direct replacement for weld stellite
5 Inconel 625,718 etc
30 RC 2 5 Upto 650 HVOF 200-400 Extreme corrosion resistance, marine, acidic and petrochem environment.
* Wear and corrosion factor rating 5 = extremely good, 4= good, 3 = Fair , 2 = moderate, 1 = poor
Coatings’ properties: Obtainable harndess.
Sprayed material Spraying technology Hardness, HV
Chrome steel Flame spraying (wire) 500 – 600
PTA 800 – 850
NiAl alloy Flame spraying 200 – 250
Copper Flame spraying (powder) 150
Stellite Flame spraying (powder)/HVOF 460 – 770
PTA 290 – 590
MCrAlY Plasma spraying 400
Self-fluxing alloy (NiCrSiB) Flame spraying/HVOF 250 – 780
PTA 360 – 820
WC-Co
Cr3C2-NiCr
HVOF spraying (powder) 1100 – 1300
750-900
Al2O3 Plasma spraying 1800 – 200019
Ball valve
20
Metal seated valve industry
Ball valve
Ball and seat Components : fully manufactured, coated , ground and lapped and Pressure tested. Supplied as ready to use pair. ½”- 14” capability
Ball valve Customers :
Schuff
KOSO
WEIR
BRAY
OLIVER
SCOPE :
A) Fully Manufacture Ball and seat as a Set
B) Coating , grinding and Lapping as a set
21
API Gate valve
22
GATE VALVE API 6A
Manufactured gate valve slab gate and seat
base material : 4140, SS 410 WITH Coating OF tungsten carbide
Industry : all API 6A valve manufacturers
Slab gate and seat – As coated TC coated Body Bushing
Slab gates finished /for NDT Fully lapped to 2 Light Band
Plug valve and Control valve
23
Plug valve
Cast steel component, fully machined, coated ground and lapped. Ball vlave coating 14” Ball valve TC coated
Pung valve –TC coating Plug valve inspection Control valve CNC machined items with coating
Control valve stems Helix valve stem
Control valve Cage : ID coated with carbide and ground
Other applications
Plug valve carbide coating plug carbide or stellite possible
Control vale cage Ball valve carbide coating
Extrusion screw coating Valve disc stellite 6 PTA
24
* Severe service Applications *
Think of us
Thank You
Bangalore : A 413, 9th main, 2nd stage,Peenya Indl area ,Bangalore 5600058
[email protected] , Tel : 080-28364565 mobile : 9886116400
………………
Pune Unit : T 180, T Block, MIDC, Bhosari, Pune 411026
[email protected] , Mobile : 8149046272
25
SPRAYMET