spirent testcenter software and hardware new …...spirent testcenter 4.70 new features november...
TRANSCRIPT
November 2016
Spirent Communications
Spirent TestCenter Software and Hardware New Features 4.70
Spirent TestCenter 4.70 New Features
November 2016 2
Table of Contents
NEW PRODUCTS AND FEATURES ................................................................................................... 3
HARDWARE……………………………………………………………………………………………………………..... 3
SOFTWARE………………………………………………………………………………………………………………….5
SPIRENT SUPPORT ......................................................................................................................... 21
Spirent TestCenter 4.70 New Features
November 2016 3
New Products and Features
Hardware
Spirent MX3 Module
Release MX3-25GD-T2 (25GbE)
Spirent FX3 Module
Release FX3-25GD-T2 (25GbE)
Spirent TestCenter 4.70 New Features
November 2016 4
Spirent C50 Appliance
C50 4-PORT 10/5/2.5/1G/100M Copper and Hardware Timing
P/N: C50-KIT-11-START
C50 Appliance
4 Port 10/5/2.5/1G/100M
Copper NIC
Hardware Timing
Spirent TestCenter
Packet Generator & Analyzer Base Package
IGMP MLD Host IP Multicast Base Package
RFC-2544 VLAN Network Device Benchmark Test Package
RFC-2889 VLAN Switching Benchmark Test Package
Spirent TestCenter 4.70 New Features
November 2016 5
Software
Spirent TestCenter release 4.70 adds support for Python 3.4 for 64-bit Ubuntu 14.04
Linux
OpenFlow Switch Emulation (OSE): BPK-1195A
Spirent TestCenter release 4.70 added the following features to OpenFlow Switch Emulation:
New Topologies: Full Mesh – Every switch is connected to every switch via a topology
port
Standalone Topology – Each switch is only connected to the controller and has no
topology connections or ports – this will allow up to 2x the number of switches for scale
testing (4000 Switches).
OpenFlow v1.4 is now supported. This is only supported on OVS version 2.5.0.
Configurable Manufacturer Description, Hardware Description, Serial Number, and
Datapath Description at the port level
Spirent TestCenter 4.70 New Features
November 2016 6
Total Switch Connection Time in milliseconds (msec) – Time for all switches to connect to
the controller.
OpenFlow Switch Emulation (OSE): BPK-1193A
Spirent TestCenter release 4.70 added a simplified discovery process in OpenFlow Controller
Emulation. All Discovery parameters are in one window. The switches and discovery will
automatically add any newly discovered switches to the Switch List.
FCOE: BPK-1081A
Spirent TestCenter release 4.70 introduces a new FCOE feature that allows the session to estabish, even if the priorities do not match. Users can check the "Iqnore FIP Priority" checkbox, and the session will establish, even if the priorites do not match.
Spirent TestCenter 4.70 New Features
November 2016 7
VXLAN EVPN Overlay Wizard with Enhanced L3VNI Features
BPK-1310A & BPK-1311A VXLAN Emulation with EVPN Learning & EVPN Emulation
Spirent TestCenter release 4.70 introduces a new VxLAN EVPN overlay wizard. The new wizard
introduces a new page, “Configure L2 L3 Segments” that allows users to configure both L2VNIs
and L3VNIs. Users can define “Tenant VRF” with its VRF ID and VRF RT format, “L2VNI” with its
step and block step, “L3VNI” with its step, the number of L2VNIs per L3VNI, and RT and RD with
pre-defined formats and offset for both L2VNI and L3VNI. The new page also provides a
dropdown menu where users can set the traffic endpoint mode to “L2-VNI”, “L3-VNI”, or both “L2
and L3-VNI”. Depending on the selected traffic endpoint mode, the wizard then displays the
configuration page for “L2VNI VM Devices”, or “L3VNI VM Devices”, or both.
VXLAN VTEP Multi-homing to Multiple Spines Using VLANs
BPK-1310A & BPK-1311A VXLAN Emulation with EVPN Learning & EVPN Emulation
In Spirent TestCenter release 4.70, the VxLAN EVPN overlay wizard now supports emulating a
single VTEP multi-homing to multiple spine switches using VLANs. To enable this feature, the
emulated VTEP must be configured with multiple VLANs; one VLAN for each of the spine
switches. Users must select the checkbox “Multi-homed VTEP across VLAN” and then set the
“Number of multihomed VTEPs per port” and “Number of DUTs”. The number of DUTs should be
equal to or less than the number of VLANs configured on the VTEP.
Spirent TestCenter 4.70 New Features
November 2016 8
The wizard creates multiple VTEP devices with the same router-id, the same number of attached
VM devices, and the same set of EVPN routes, to emulate a single multi-homed VTEP. These
VTEP devices will have same MAC address, IPv4 address, and IPv4 default gateway address by
default.
EVPN Stream Based Results
BPK-1311A EVPN Emulation
Spirent TestCenter release 4.70 supports a new MAC stream result view, IPv4 stream result
view, and IPv6 stream result view under the EVPN Stream Results option.
The EVPN MAC Stream Result view displays information such as: inner source/destination MAC
address, outer source/destination MAC address, and EVPN MPLS label information, in real time
for each virtual machine/host to virtual machine/host traffic stream.
Spirent TestCenter 4.70 New Features
November 2016 9
Similarly, for EVPN IPv4 and IPv6 stream results, the feature displays: IPv4 or IPv6 address, and EVPN MPLS label information, in real time for each virtual machine/host to virtual machine/host traffic stream.
VxLAN Merge VNI Configurations from Multiple Wizard Runs
BPK-1310A VxLAN Emulation with EVPN Learning
Spirent TestCenter release 4.70 supports running the VxLAN wizard multiple times on different
test ports, and then merging the L2VNI/L3VNI/VM configurations from multiple wizard runs, in
certain scenarios:
If there is a single L2VNI per block in each of the wizard runs, merging the L2VNI and VM
configuration from multiple wizard runs is supported.
If there are multiple L2VNIs per block, and the expanded L2VNI set from multiple wizard runs are
the same, merging the configurations is supported.
However, if there are multiple L2VNIs per block, and the expanded L2VNI set from multiple
wizard runs are not the same, merging the configurations from multiple wizard runs is not
supported.
If L3VNI is also used, configurations from multiple wizard runs are only merged if the L3VNI
value/count/step from multiple wizard runs are the same, and if L2VNI configurations from
multiple wizard runs can also be merged.
VXLAN L3 Distributed Gateway
BPK-1310A VXLAN EVPN Learning
Spirent TestCenter release 4.70 supports L3 VxLAN gateway functionality on emulated VTEPs.
An emulated VTEP can send traffic from simulated virtual machine hosts in a local L2 segment to
simulated virtual machine hosts in another L2 segment, on a different emulated VTEP, using
L3VNI.
For example, users can configure VM1 in a local segment with L2VNI 100 and IP subnet
100.1.1.0/24 on VTEP1, and VM2 in another segment with L2VNI 200 and IP subnet
200.1.1.0/24 on VTEP2. Then, use L3VNI 10000 to send bidirectional traffic between the VM1
and VM2.
Spirent TestCenter 4.70 New Features
November 2016 10
Spirent TestCenter 4.70 New Features
November 2016 11
OSPFv3 Extended LSA Full Mode
BPK-1004A & BPK-1004B Unicast Routing Base Package A & B
Spirent TestCenter release 4.70 supports OSPFv3 extended LSA full mode. To use the OSPFv3
Extended LSA feature, use the existing OSPFv3 Wizard to set up Legacy OSPFv3 routers and
LSAs, and then at the OSPFv3 router level, set “Enable Extended LSA” to true.
Extended router, network, inter-area prefix, inter-area router, AS external, NSSA, Link and intra-
area prefix LSAs are supported. For each type of extended LSA, users can add new LSAs and
associated TLVs and sub-TLVs for the extended LSA. Use the OSPFv3 action commands to
age/re-advertise the Extended LSAs. The OSPFv3 Result View is extended with counters for the
new Extended LSAs.
Spirent TestCenter 4.70 New Features
November 2016 12
PCEP Router Block
In Spirent TestCenter release 4.70, users can change the device count of PCE or PCC to more than one, which allows users to create multiple PCE/PCC sessions per deviceblock level.
The Speaker Entity Identifier was a changed from a fixed value/string to a wildcard, to support more sessions from the same deviceblock. Currently, only @b wildcard is supported without Preview.
In the Association Groups dialog, there are new columns to input the offset; "Association ID Device Offset" and "IPv4 Association Source Device Offset" for IP Version "IPv4", and new column "IPv6 Association Source Device Offset" for IP Version "IPv6".
On the Edit PCEP LSPs tab, when users edit the LSP in ASSOCIATION Groups dialog, there are new columns: "Association ID Device Offset" and "IPv4 Association Source Device Offset" for IP Version "IPv4." For IP Version “IPv6” there is a new column "IPv6 Association Source Device Offset."
Spirent TestCenter 4.70 New Features
November 2016 13
In PCEP LSP Configuration (both PCC LSP and PCE LSP), when the Device IP version is IPv6,
there are two new columns: "Source IPv4 Address Device Offset" and "Destination IPv4 Address
Device Offset" to increment the LSP source and destination address across PCE/PCC sessions.
When the Device IP version is IPv6, there are two new columns: "Source IPv6 Address Device
Offset" and "Destination IPv6 Address Device Offset."
By editing the LSP Info tab, users can input the starting LSP ID, Tunnel ID, and Device Offset to
specify how IP addresses should increment across all LSPs under the device block.
Spirent TestCenter 4.70 New Features
November 2016 14
In PCC LSP Results/PCE LSP Results, release 4.70 added results for DeviceBlock and LSP block level.
BGP Flowspec for IPv6 : New! BPK-1335A
BGP IPV6 FLOWSPEC BASE PACKAGE A
Spirent TestCenter release 4.70 adds support for BGP Flowspec for IPv6, as per the draft version v6-07 at the link below :
https://tools.ietf.org/html/draft-ietf-idr-flow-spec-v6-07
Spirent TestCenter release 4.70 supports both Type-1 and Type-2 for RT re-direct.
Users can add multiple VPN routes as a block and set the RT redirect value (see blue column)
for each VPN as shown below.
Spirent TestCenter release 4.70 adds BGP-Flowspec redirect to IPv6 Next-hop.
Spirent TestCenter 4.70 New Features
November 2016 15
FlexLSP/ RSVP-TE ASSOCIATED BIDIRECTIONAL LSP: New! BPK-1334A RSVP-TE ASSOCIATED BIDIRECTIONAL LSP BASE PKG A
Spirent TestCenter release 4.70 introduces a new feature for RSVP-TE Bi-dir LSP (FlexLSP). To enable FlexLSP, users edit the RSVP Tunnels/LSP to enable IPv4 Ext. Association Object and Association type, either Single or Double sided; this translates to Co-routed and non co-routed LSPs.
Users can modify the tunnel count to more than 1, to increase the number of tunnels, when the association ID is set to increment to 1. Users can also set LSP increment count to more than 1, in order to get a similar effect with different LSP IDs. However, when users enable both the increment options (Tunnel Count and LSP Count set to more than one), it actually multiplies the count using the n x n algorithm.
There is no option to enable/disable reverse object for FlexLSP; however, when associate ERO
object is set on the Reverse Object column, reverse object is sent automatically. Refer to the
screen capture below.
Spirent TestCenter 4.70 New Features
November 2016 16
Users must add multiples of ERO that can be used for forwarding and reverse object before
editing reverse object.
Spirent TestCenter 4.70 New Features
November 2016 17
PPPoE IPCP Address Option
Spirent TestCenter release 4.70 added the capability for users to specify and request a non-zero
IP address as part of IPCP options in PPPoE.
Spirent TestCenter 4.70 New Features
November 2016 18
Spirent TestCenter 4.70 New Features
November 2016 19
DHCPv4 and DHCPv6/PD Auto-retry realism
Spirent TestCenter release 4.70 added functionality for DHCPv4, DHCPv6, DHCPv6-PD to auto-
retry any failed or flapped DHCP sessions with support for two modes – session mode and block
mode.
AVB Features and Enhancements
Spirent TestCenter release 4.70 added several enhancements, usability features, and qualified
support for the FX2 and MX2 family of test cards.
Improvements for AVB protocols
Correction to gPTP Automotive profile Master role - no change to the UI
Support for MVRP periodic timer
Spirent TestCenter 4.70 New Features
November 2016 20
SRP per Stream Information
Enables users to view the stream information of transmitted and received streams on each
device by SRP protocol. The Stream information file (on chassis: /tmp) displays the details of
talker streams and the streams subscribed by the listeners.
Spirent TestCenter 4.70 New Features
November 2016 21
Spirent Support
To obtain technical support for any Spirent Communications product, please contact our Support
Services department using any of the following methods:
Americas
E-mail: [email protected]
Web: https://support.spirent.com/SpirentCSC/
Toll Free: +1 800-SPIRENT (+1 800-774-7368) (North America)
Phone: +1 818-676-2616
Hours: Monday through Friday, 06:30 to 18:00 Pacific Time
Europe, Middle East, Africa
E-mail: [email protected]
Web: https://support.spirent.com/SpirentCSC/
Phone: +33 (1) 6137 2270 (France)
Phone: +44 1803 546333 (UK)
Hours: Monday through Thursday, 09:00 to 18:00, 9:00 to 17:00 Friday, Paris Time
Asia Pacific
E-mail: [email protected]
Web: https://support.spirent.com/SpirentCSC/
Phone: +86 (400) 810-9529 (toll-free mainland China only)
Phone: +86 (10) 8233 0033 (China)
Operating Hours: Monday through Friday, 09:00 to 18:00 Beijing Time
Company Address
Spirent Communications, Inc.
27349 Agoura Road
Calabasas, CA 91301
USA
The latest versions of user manuals, application notes, and software and firmware updates are available on the Spirent
Communications Customer Service Center website at https://support.spirent.com/SpirentCSC/.
Information about Spirent Communications and its products and services can be found on the main company website
at http://www.spirent.com.
© 2016 All of the company names and/or brand names and/or product names referred to in this document, in particular, the name
“Spirent” and its logo device, are either registered trademarks or trademarks of Spirent plc and its subsidiaries, pending registration in
accordance with relevant national laws. All other registered trademarks or trademarks are the property of their respective owners.