specifications & installation instructions...specifications & installation instructions 1206...

Specifications & Installation Instructions

1206 M Avenue Kearney, NE 68847 • P: 800.445.6404 • F: 855.234.9401 • TaskLighting.com

TABLE OF CONTENTSTR Series Angle Power Strip Specifications.........................................................pg. 3-4TR Series Angle Power Strip Custom Options.....................................................pg. 5 TR-USB Series Angle Power Strip Specifications...............................................pg. 6-7TR/TR-USB Series Angle Power Strip Installation Instructions ..........................pg. 8APT Series Angle Power Strip Specifications.....................................................pg. 9-10APT Series Angle Power Strip Installation Instructions .......................................pg. 11 Lighted Power Strip DV Series Specifications...................................................pg. 12-13Lighted Power Strip DV Series Installation Instructions.....................................pg. 14-15Lighted Power Strip RM Series Specifications...................................................pg. 16-17Lighted Power Strip RM Series Installation Instructions....................................pg. 18 sempriaLED SG9 Series Specifications.........................................................pg. 19sempriaLED SG9 Series Installation Instructions ...........................................pg. 20-21sempriaLED A Series Specifications..............................................................pg. 22sempriaLED F Series Specifications..............................................................pg. 23SsempriaLED A & F Series Installation Instructions.........................................pg. 24-25 sempriaLED R Series Specifications..............................................................pg. 26sempriaLED R Series Installation Instructions................................................pg. 27-28sempriaLED S Series Specifications...............................................................pg. 29sempriaLED S Series Installation Instructions................................................pg. 30-31sempriaLED Lighted Closet Rod Specifications...............................................pg. 32sempriaLED Lighted Closet Rod Installation Instructions...............................pg. 33sempriaLED Puck Specifications......................................................................pg. 34sempriaLED Mini Can Specifications...............................................................pg. 35sempriaLED Puck/ Mini Can Installation Instructions.......................................pg. 36sempriaLED Supporting Products...........................................................................pg. 37sempriaLED 120V Bar Light Specifications.............................................................pg. 38sempriaLED 120V Bar Light Installation Instructions................................................pg. 39

800.445.6404 • TaskLighting.com 3TR-SPEC-0618

TR Series Angle Power StripTamper Resistant Duplex Receptacles eliminate cutouts for receptacles and switches in your backsplash

Specifications

Features

• Kitchens• Baths• Offices & Computer Labs• Islands• Shops & Garages

Applications

Construction Materials: Powder Coated Aluminum

Input Voltage: 120V

Mounting: Wood Screws & Wall Anchors

Wiring: 12 ga. Romex

Environment: Dry Only

Optional Installation Components

Finish Options

Receptacle Colors

• Tamper Resistant Duplex Receptacles• Easy Installation• Designer finishes to blend with any decor• 3-Year Limited Warranty• Custom options include: USB Ports, Phone Jacks, Cable

Jacks, Data Ports. See pg. 5 for more options.

Section Drawing

Part Number Length # of Duplex Recept.

Recept.Color Finish

TR9-1ColorD-P-Finish 9" 1 B, G, W BK, BZ, SN, WT










TR Series Angle Power Strip

PART NUMBER DIMENSIONS DESCRIPTION

TR-SQ-JB-P-Finish 3" x 3" x 2-1/8" Square Junction Box

2-1/8"

7/8"

2-1/4"

2-1/2"

Black (B) Gray (G) White (W)

White (WT)Satin Nickel (SN)Bronze (BZ)Black (BK)

800.445.6404 • TaskLighting.com4 TR-SPEC-0618

• Receptacles must be a minimum of 5" apart (on center)

• Receptacles must be a minimum of 3" from the end

• Custom charges will apply, call for a quote and assistance with your custom order

• Call for lead time

= Knock-out (all knock-outs are 1-1/2" from end)

= Receptacle (15A receptacle standard)

Custom Options

Custom Option Details

• Custom lengths from 7" - 92" (sizes over 92" will have a seam when assembled)

• Additional devices (see page 5)

• Custom device placement

Legend

42"

48"

TR24-2ColorD-Finish

TR12-1ColorD-Finish

TR9-1ColorD-Finish

18"

TR18-2ColorD-Finish

12"

9"

24"

30"

TR30-2ColorD-Finish

36"

TR36-2ColorD-Finish

TR42-3ColorD-Finish

TR48-3ColorD-Finish

60"

TR60-4ColorD-Finish

72"

TR72-4ColorD-Finish

1-1/2"

12" 12"

12" 12"

6"

12"12" 12 "

12"12 "

10" 11" 10"11"

12" 12" 12"

10" 10" 10"

7-1/2" 9" 7-1/2"

6" 6" 6"

6"

4-1/2"

14-1/4" 14-1/4" 14-1/4" 14-1/4" 14-1/4"

TR Series Angle Power StripTamper Resistant Duplex ReceptaclesInstalled view

1-1/2"

1-1/2" 1-1/2"

1-1/2" 1-1/2"

1-1/2" 1-1/2"

1-1/2" 1-1/2"

1-1/2" 1-1/2"

1-1/2" 1-1/2"

1-1/2" 1-1/2"

1-1/2" 1-1/2"

1-1/2" 1-1/2"

4-1/2"

800.445.6404 • TaskLighting.com 5TR-CUSTOM-0618

TR Series Angle Power StripCustom Options

TR Series Custom OptionsCUSTOM LENGTHSCustom lengths to the 1/4˝ from 7" - 92" (larger sizes will have a seam when assembled)

SWITCHESPART NUMBER DESCRIPTION COLORTRO-SPS-Color Decora single-pole rocker switch B, G, W

TRO-SPS-20A-Color Decora 20 Amp single-pole rocker switch B, G, W

TRO-3WS-Color Decora 3-way rocker switch B, G, W

TRO-3WS-20A-Color Decora 20 Amp 3-way rocker switch B, G, W

TRO-4WS-Color Decora 4-way rocker switch B, G, W

TRO-DS-2SPS-Color Decora double switch B, G, W

TRO-DS-(2)3WS-Color Double switch with (2) 3-way B, W

TRO-DS-1P/3P-Color Double switch with single-pole & 3-way B, G, W

TRO-TS-3SPS-Color Decora triple switch w/ three single-pole switches B, W

RECEPTACLESTRO-15A-REC 15 Amp tamper resistant receptacle B, G, W

TRO-20A-REC 20 Amp tamper resistant receptacle B, G, W

RECEPTACLES/SWITCH COMBOTRO-USB/REC Combination (2) USB ports and receptacle B, G, W

TRO-CB-1P/REC-Color Combination single-pole switch and receptacle B, G, W

TRO-CB-3P/REC-Color Combination 3-way switch & receptacle B, G, W

CONNECTORSTRO-CJ-Color Decora style Cable Jack, "F" Style, for 75 Ohm coaxial cable B, G, W

TRO-PJ-Color Decora style 6 conductor telephone jack B, G, W

TRO-HDMI-Color HDMI Port Connector W

PORT FRAMESTRO-2PORT-ColorTRO-3PORT-ColorTRO-4PORT-ColorTRO-6PORT-Color

Decora style multimedia insert. Allows you to combine your choice of 2, 3, 4, or 6 voice, data, audio, or video connectors into one compact, attractive wallplate

B, G, W

SNAP-IN CONNECTORS

TRO-CON-BLANK-Color Blank insert used to cover up any unused openings in any of the Port Frames B, G, W

TRO-CON-CAT6-Color Snap-in Data Category 6 8-conductor component-rated connector. 250 MHz B, G, W

TRO-CON-CJ-Color Snap-In cable jack. B, G, W

TRO-CON-PJ-8-Color 6-conductor USOC voice grade phone (jack) connector B, G, W

TRO-CON-HDMI-Color HDMI feed through Quick Port Connector B, W

POWER SUPPLIESTRO-TLD-D30WSO 15V DC 30W hardwire

TRO-TLD-D45WSO 15V DC 45W hardwire



TRO-LPV-20W-15V 15V DC 20 Watt LED power supply (use with wireless dimming system)

TRO-LPV-35W-15V 15V DC 35 Watt LED power supply (use with wireless dimming system)

TRO-3WS,TRO-4WS, TRO-SPS

TRO-DS-2SPS-W

TRO-CON-PJ TRO-CON-CAT6TRO-CON-CJ

Switches

Power Supply

TRO-2PORT, TRO-3PORT, TRO-4PORT & TRO-6PORT

TRO-PJ TRO-CJ

Snap-in Connectors

TRO-20A-RECTRO-15A-REC

Connectors

Port Frames

Combination Devices

TRO-USB/RECTRO-CB-IP/REC& TRO-CB-3P/REC

Receptacles

TRO-HDMI

TRO-TLD-D30WSOTRO-TLD-D45WSOTRO-TLD-D60WSOTRO-TLD-D75WSO

TRO-CON-HDMI

TRO-LPV

TRO-CON-BLANK

800.445.6404 • TaskLighting.com6

TR-USB Series Angle Power StripTamper Resistant Receptacles with USB included

Specifications

Features

• Kitchens• Baths• Offices & Computer Labs• Islands• Shops & Garages

Applications


Input Voltage: 120V




Optional Installation Components

TRU-SPEC-0618

Finish Options

Receptacle Colors

• Tamper Resistant• Easy Installation• Designer finishes to blend with any decor• 3-Year Limited Warranty

Section Drawing

Part Number Length# of USB/Recept. Combo

# of Duplex Recept.

Recept.Color Finish

TRU9-1ColorD-P-Finish 9" 1 B, G, W BK, BZ, SN, WT

TRU12-1ColorD-P-Finish 12" 1 B, G, W BK, BZ, SN, WT

TRU18-2ColorD-P-Finish 18" 1 1 B, G, W BK, BZ, SN, WT








USB device always positioned on left

PART NUMBER DIMENSIONS DESCRIPTION

TR-SQ-JB-P-Finish 3" x 3" x 2-1/8" Square Junction Box

2-1/8"

7/8"

2-1/4"

2-1/2"

USB/Receptacle Combo Colors


Black WhiteGray

Black WhiteGray

800.445.6404 • TaskLighting.com 7TRU-SPEC-0618

TR-USB Series Angle Power StripTamper Resistant Receptacles with USB includedInstalled view


= Receptacle (15A receptacle standard)

Legend

= USB/ Receptacle Combo (15A receptacle standard)

42"

48"

TRU24-2ColorD-Finish


TRU9-1ColorD-Finish

18"


12"

9"

24"

30"


36"




60"


72"


12" 12"

12" 12"

6"

12"12" 12 "

12"12 "

10" 11" 10"11"

12" 12" 12"

10" 10" 10"

7-1/2" 9" 7-1/2"

6" 6" 6"

6"

4-1/4"

14-1/4" 14-1/4" 14-1/4" 14-1/4" 14-1/4"

1-1/2"1-1/2"

1-1/2" 1-1/2"

1-1/2" 1-1/2"

1-1/2" 1-1/2"

1-1/2" 1-1/2"

1-1/2" 1-1/2"

1-1/2" 1-1/2"

1-1/2" 1-1/2"

1-1/2" 1-1/2"

1-1/2" 1-1/2"

4-1/4"


1 2 3Secure APS – TR Series to wall with screws into each stud or use anchors provided. Strip wires and connect BLACK wire from romex to GOLD terminal and WHITE wire from romex to SILVER terminal. Ground all GREEN wires to PEM studs inside of back frame. When connecting two APS – TR Series, run Romex from piece A to piece B. Ground each section to the next.

TR-INSTALL-0618

Turn power off at panel. Carefully pry open each piece with tool (provided). Insert Romex connector into hole. Pull wires into APS-TR Series.

W2436 Valance

GFCI Turn power off!

To electrical panel

W1836 W2436

12-2 Romex

(Max. 15 Amps)

(Piece A)

(Max. 15 Amps)

(Piece B)

Angle Power Strip-TR SeriesWire Entry Wire Entry

Wire Entry12-2 Romex

1

1

2

33

Angle Power Strip-TR Series

To terminate last APS- TR Series, use wire nuts on ends of wires. Snap cover in place, and turn power on. Firmly insert plug straight into receptacle, applying equal pressure to both blades at the same time. Gently rock plug, if needed.

General Guidelines• Power source MUST be a 20 amp branch circuit protected by a GFCI at the panel or GFCI prior to the connection at APS.• All wiring must meet NEC® and local codes. The Angle Power Strip (APS) must be installed by a licensed electrician.• Firmly insert plug straight into receptacle, applying equal pressure to both blades at the same time. Gently rock plug, if needed.

TR/TR-USB Series Angle Power StripInstallation Instructions

800.445.6404 • TaskLighting.com 9

Specifications Optional Installation Components PART NUMBER DIMENSIONS DESCRIPTION

SQ-JB-Finish 3˝ x3˝ x 1-1/2˝ Square Junction Box

Section Drawing

Finish Options

Receptacle Colors• Kitchens• Baths• Offices & Computer Labs• Islands• Shops & Garages

Applications

APT-SPEC-0618

• Tamper Resistant• Easy Installation• Designer finishes to blend with any decor• 3-Year Limited Warranty

Features

Part Number Length # of Recept.

Recept.Color Finish

APT9-2Color-P-Finish-*Position 9" 2 B, G, W BK, BZ,SN, WT



APT24-4Color-P-Finish 24" 4 B, G, W BK, BZ,SN, WT







*Indicate Left (L) or Right (R) side wire entry


Input Voltage: 120V




1-1/2"

1-5/8"

1-11/16"

3/4"

APT Series Angle Power StripTamper Resistant Receptacles eliminate cutouts for receptacles and switches in your backsplash

White (WT)


Satin Nickel (SN)Bronze (BZ)Black (BK)


• Receptacles must be a minimum of 1-1/2" apart (on center)

• Receptacles must be a minimum of 1" from end. (Requires wire entry at opposite end of fixture)

• Custom charges will apply. Call for a quote and assistance with your custom order.

• Call for lead time

APT-SPEC-0618


= Receptacle (Available in Black, Gray, or White)

Custom Options

Custom Option Details

• Custom lengths from 6" - 92" (larger sizes will have a seam when assembled)

• 120 Volt integral switch (available in black or white only)

• Additional receptacles

• Custom receptacle/switch placement

Legend

18"

12"

9"

24"

30"

36"

42"

48"

60"

72"8-1/4"7-1/8" 7-1/8"

1-1/2"

7-1/2"

7"8-1/2"7"

7"7" 7" 7" 7" 7"

7-1/8"5-1/4"

3-1/4" 7-1/8"

7" 3-1/2" 4"

7"2-1/2"

5" 2" 2"

APT Series Angle Power StripInstalled view

8-1/4"8-1/4"8-1/4"8-1/4"8-1/4"8-1/4"

7-1/2" 7-1/2" 7-1/2" 7-1/2" 7-1/2" 7-1/2"7-1/2"

8-1/2"8-1/2"8-1/2"

1-1/2"

1-1/2" 1-1/2"

1-1/2" 1-1/2"

1-1/2" 1-1/2"

1-1/2" 1-1/2"

1-1/2" 1-1/2"

1-1/2" 1-1/2"

1-1/2"

1-1/2"

1-1/2"

2-1/2"

3-1/2"

3-1/4"3-1/4"7-1/8"

5-1/4"5-1/4"7-1/8"

7-1/8"7-1/8" 7-1/4"7-1/4"7-1/4"


APS

W2436 Valance

General Guidelines• Power source MUST be a 20 Amp branch circuit protected by a GFCI at the panel or GFCI prior to the connection at APS.• All wiring must meet NEC® and local codes. The Angle Power Strip (APS) must be installed by a licensed electrician.• Firmly insert plug straight into receptacle, applying equal pressure to both blades at the same time. Gently rock plug, if needed.

GFCI Turn power off!

To electrical panel

W1836 W2436

12-2 Romex

(Piece A)(Piece B)

APSWire Entry Wire Entry

Wire Entry12-2 Romex

1

1

2

33

APT-INSTALL-0618

Turn power off at panel. Carefully pry open each piece with tool (provided). Insert Romex connector into hole with locknut on back frame. Pull wires into APS.

Secure APS to wall with screws into studs or use anchors provided. Strip wires and connect BLACK to BLACK, WHITE to WHITE. Ground all GREEN wires to PEM studs inside of back frame. When connecting two APS, run Romex from fixture to fixture. Ground each section to the next.

1 2 To terminate last APS, use wire nuts on ends of wires. Snap cover in place and turn power on. Firmly insert plug straight into receptacle, applying equal pressure to both blades at the same time. Gently rock plug, if needed.

3

APT Series Angle Power StripInstallation Instructions


Lighted Power Strip DV SeriesSpecifications for LPS WITH Built-In Driver

PART NUMBER LENGTHTOTAL WATTS

#OF RECEPT.

RECEPT. COLOR FINISH KELVIN TEMP

LUMENSBased on 3000K

(approx. per fixture)*

LPS10QDV2ColorFinishTemp 10-1/2" 2W 1 B, G, W BK, BZ, SN, WT 27K, 30K, 40K, 50K 207






S-LPS-DVSERIES-SPEC-0618

Specifications WITH BUILT-IN DRIVER

Finish Options

Receptacle Colors

• Under Cabinets• Under Fixed Shelving• Office Cubicles• Shops & Garages

Applications• Medium Light Output - 1/4 Watt LEDS• INTEGRAL DRIVER• Tamper Resistant APS with integrated LED Lighting• Rocker Switch• 3-Year Limited Warranty• Dimmable with separate lighting circuit• No UV or IR

Features

Construction Materials:

Powder Coated Extruded Aluminum (heatsink), IR Acrylic (lens)

Wattage: 1/4 Watt LEDs

Color Temp (Kelvin): 2700K (Warm White), 3000K (Soft White)4000K (Cool White), 5000K (Daylight White)

CRI: 90+

LED Beam Angle: 120º

LED Spacing: 1-1/2"

LED Board: 6" or 12"

Input Voltage: 120V


Wiring: 12 ga.Romex


24-1/2” fixture shown

2-5/8"

3/8"

1-5/8"

1-5/8"

1"

Fixture Section

Medium Light Output - 1/4 watt

Dimming OptionsPART NUMBER DESCRIPTIONDVELV-300P 300W Diva slide dimmer

DVELV-303P 300W Diva slide dimmer 3-way

MAELV-600-Color Maestro electronic smart dimmer

MA-R-Color Maestro companion dimmer




1-1/2"

S-LPS-DVSERIES-SPEC-0618

Lighted Power Strip DV SeriesSpecifications for LPS WITH Built-In DriverInstalled view

WITH Built-In Driver and Switch - Medium Light Output -1/4 Watt

= Knock-out (1-1/2" from right side - 5-1/2" from left side) located on back frame

Legend

= Receptacle (Available in White, Gray, and Black)

= Switch (Available in Black or White- 4-1/2" from left side)

= Divider Plate (Low Voltage)

= Driver

3-1/2"

4-1/2"

Back Frame

Cover

NOTE: 6"LED board is mounted in center of 10-1/2" fixture

LPS24DV8ColorFinishTemp



18-1/2"3" 5"10-1/2"


1"

12-1/2"10"

1"

10-1/2"9-1/2"

24-1/2"10-1/2" 3"3" 3" 5"

30-1/2"11" 6"4-1/2"


36-1/2"5-1/2"

LPS36DV12ColorFinishTemp12-1/2" 6" 6"6"6"

Divider Plate

DRIVER

1-1/2"5-1/2"

1-1/2"5-1/2"

1-1/2"5-1/2"

5-1/2"

5-1/2"

1-1/2"

4-1/2"4-1/2"

800.445.6404 • TaskLighting.com14 S-LPS-DVSERIES-INSTALL-0618

Lighted Power Strip DV SeriesInstallation Instructions for LPS WITH Built-In Driver

Turn power off at panel. Carefully pry open each piece with tool (provided). Insert Romex connector into knockout hole inside of back frame. Pull wires into LPS.

Tool

WTWTGRN

BKBK

120VDIVIDER PLATE

SWITCH

DRIVER

RED +BLUE -

WT

WTWT GRN

GRN

GRN

BK

BK

BK

General Guidelines• Power source MUST be a 20 amp branch circuit protected by a GFCI at the panel or GFCI prior to the connection at LPS.• All wiring must meet NEC® and local codes. • Light valance recommended.• Firmly insert plug straight into receptacle, applying equal pressure to both blades at the same time. Gently rock plug, if needed.

WTWTGRN

BKBK

120VDIVIDER PLATE

SWITCH

DRIVER

RED +BLUE -

WTWT GRN

GRN

BKBK

FactoryWired

FactoryWired

Secure LPS to wall by screwing into wall studs or use anchors provided. Connect BLACK Romex wire to BLACK wire from receptacles and switch. Connect WHITE Romex wire to WHITE wire from receptacles and driver. Ground all GREEN wires to PEM studs inside of back frame.

Wiring for Combined Light and Receptacle Circuit - Non Dimmable

To terminate last LPS, use wire nuts on ends of wires.

When connecting 2 or more LPS fixtures, run Romex from fixture to fixture. Ground each section to the next.

Snap cover in place and turn power on.

Secure LPS to wall by screwing into wall studs or use anchors provided. If running two circuits, one for receptacles, one for lighting, connect fixture wires to appropriate Romex wires. BLACK to BLACK. WHITE to WHITE. Ground all GREEN wires to PEM studs inside of back frame.

Wiring for Separate Light and Receptacle Circuits

Bottom of Cabinet

Step 1 Step 2

Step 3

Step 4


When connecting 2 or more LPS fixtures, run Romex from fixture to fixture. Ground each section to the next.


Step 2

Step 3

Step 4

Step 1

12-1/2” Fixture Shown

12-1/2” Fixture Shown120V for receptacles

120Vfor lights

800.445.6404 • TaskLighting.com 15S-LPS-DVSERIES-INSTALL-0618

120V ReceptacleCircuit. Must beGFCI Protected. (non dimmable)

Lighting Circuit

Back Frame

Positive (+)

Negative (-)

Wiring Diagram for Separate Light & Receptacle Circuits

Back Frame

Cover

Positive (+)Negative (-)

Wiring Diagram for Combined Light & Receptacle Circuit - Non Dimmable

Cover



Divider Plate

Divider Plate

DRIVER

DRIVER

120V ReceptacleCircuit. Must beGFCI Protected.

Lighted Power Strip DV SeriesWiring Diagram for 18-1/2" LPS WITH Built-In Driver


Lighted Power Strip RM SeriesSpecifications for LPS WITHOUT Built-In Driver

S-LPS-RMSERIES-SPEC-0618


Powder Coated Extruded Aluminum (heatsink), IR Acrylic (lens)



CRI: 90+LED Beam Angle: 120ºLED Spacing: 1-1/2"LED Board: 6" or 12"Input Voltage: 120V (receptacles) & 15 Volt DC (lighting)Mounting: Wood Screws & Wall Anchors

Wiring: 18/2 solid (recommended)- for Lighting 12 ga. Romex- for Receptacle

Environment: Dry OnlyMax Run: Refer to Driver Specs

Optional Installation Components PART NUMBER DESCRIPTIONAPS-Switch Rocker Switch (available in Black or White)

APT-R-15A 15Amp Tamper Resistant Receptacle. Available in Black, Gray, and White

Task Lighting retains the right to modify the design of our products without prior notice

PART NUMBER DESCRIPTION/ OUTPUT INPUTTLD-D30WSO 30W hardwire 15V DC, 2A max. 120V AC, .3ATLD-D45WSO 45W hardwire 15V DC, 3A max. 120V AC, .4ATLD-D60WSO 60W hardwire 15V DC, 4A max. 120V AC, .5ATLD-D75WSO 75W hardwire 15V DC, 5A max. 120V AC, .6A

PART NUMBER LENGTHTOTAL WATTS

#OF RECEPT.

RECEPT. COLOR FINISH

KELVIN TEMP



LPS10HRM3ColorFinishTemp 10-1/2" 3W 1 B, G, W BK, BZ, SN, WT 27K, 30K, 40K, 50K 270










White (WT)

Finish Options

Satin Nickel (SN)Bronze (BZ)Black (BK)

Receptacle Colors

• Under Cabinets • Office Cubicles• Under Fixed Shelving • Shops & Garages

ApplicationsFeatures

24-1/2” fixture shown


2-5/8"

1/2"

1-5/8"

1-5/8"

1"

Fixture Section

Specifications WITHOUT DRIVER

Power Supplies

• High Light Output - 1/2 Watt LEDs• REMOTE DRIVER• Tamper Resistant APS with integrated LED Lighting• 3-Year Limited Warranty• Dimmable (with compatible dimmer)• No UV or IR

High Light Output - 1/2 watt





**WS-LED-CVD-902 Sempria dimming module for wireless system

*WS-SR-Color-902Sempria wireless dimmer/ switch. Available in Black, Gray, Ivory, Light Almond, and White**NOTE: Call TASK for alternate driver

800.445.6404 • TaskLighting.com 17S-LPS-RMSERIES-SPEC-0618

Lighted Power Strip RM SeriesSpecifications for LPS WITHOUT Built-In DriverInstalled view

Custom Options/Details

Legend

= Low Voltage Entry (1-1/2" from left side) located on back frame

= Receptacle (Available in WT, GR, or BK)

= Divider Plate (Low Voltage)

• Custom lengths from 10-1/2" - 72-1/2" (larger sizes will have a seam when assembled)

• 120 Volt integral switch (available in black or white only)

• Custom receptacle/switch placement• Receptacles must be a minimum of

1-1/2” apart (on center)

• Receptacles must be a minimum of 1” from right side & 5-1/2” from left side. Knockout cannot be behind device.

• Custom charges will apply - Call for a quote, lead time, and assistance with your custom order

= Knock-out (1-1/2" from right side - 5-1/2" from left side). located on back frame

Back Frame

Cover

1½"

NOTE: 6"LED board is mounted in center of 10-1/2" fixture

LPS24RM12ColorFinishTemp



18-1/2"3" 5"10-1/2"


1"

12-1/2"10"

1"

10-1/2"9-1/2"

24-1/2"10-1/2" 3"3" 3" 5"

30-1/2"4-1/2"11" 6"


36-1/2"

LPS36RM18ColorFinishTemp12-1/2" 6" 6"6"6"

42-1/2"


48-1/2"


60-1/2"


72-1/2"

10-3/4" 6-3/4"

11-1/2" 9"7"7"7"7"

7"7"7"7" 7"7"11-1/2" 7"

12" 8"

5-1/2"

Divider Plate

1-1/2"

5-1/2"

5-1/2"

5-1/2"

5-1/2"

5-1/2"

5-1/2"

5-1/2"

5-1/2"

5-1/2"

1-1/2"

1-1/2"

1-1/2"

1-1/2"

1-1/2"

1-1/2"

1-1/2"

7-1/2"7-1/2" 7-1/2" 7-1/2"7-1/2"7-1/2"7-1/2"LPS72RM36ColorFinishTemp

6-1/4"6-1/4"6-1/4"6-1/4"

4-1/2" 4-1/2"

1-1/2"


Lighted Power Strip RM SeriesInstallation Instructions for LPS WITHOUT Built-In Driver

S-LPS-RMSERIES-INSTALL-0618

Using appropriate knockout hole, pull low voltage wire from remote power supply into the low voltage space, connect BLACK wire (negative) to BLACK wire from lights and RED wire (positive) to RED wire.


Turn power off at panel. Carefully pry open each piece with tool (provided). Insert Romex connector into knockout hole inside of back frame. Pull wires into LPS.

General Guidelines• Power source MUST be a 20 amp branch circuit protected by a GFCI at the panel or GFCI prior to the connection at LPS.• All wiring must meet NEC® and local codes. • Light valance recommended.• Firmly insert plug straight into receptacle, applying equal pressure to both blades at the same time. Gently rock plug, if needed.

Secure LPS to wall by screwing into wall studs or use anchors provided. Connect BLACK to BLACK, WHITE to WHITE. Ground all GREEN wires to PEM studs inside of back frame.

Bottom of Cabinet

Remote Driver- 120V Entry


GRNGRNGRN

GRN

BK

WT

BK

WT

BK

120VDIVIDER PLATELOW VOLTAGE

RED +

BLACK -

WT

When connecting two LPS, run Romex from fixture to fixture. Ground each section to the next.

Remote Driver-Low Voltage Entry


Tool


Step 2

Step 3

Step 4Step 1

Step 5

15vDC wire

120V Circuit

Positive (+)Negative (-)

Back Frame

Cover

Divider Plate

19800.445.6404 • TaskLighting.com

White (W)Gray (G)Black (B)

SG9-SPEC-0618

SG9 SeriesLinear under cabinet LED Lighting with integrated WireWay system for concealed wire management

• Wire management system• Conceals wire from wall to fixture• Available in Black, Gray, and White

PART NUMBER DESCRIPTION/ OUTPUT INPUTTLD-24WSI* 24W plug in 15V DC Plug In

TLD-D30WSO 30W hardwire 15V DC, 2A max. 120V AC, .3ATLD-D45WSO 45W hardwire 15V DC, 3A max. 120V AC, .4ATLD-D60WSO 60W hardwire 15V DC, 4A max. 120V AC, .5ATLD-D75WSO 75W hardwire 15V DC, 5A max. 120V AC, .6A

PART NUMBER DIMENSIONS TOTAL WATTS

KELVINTEMP



SG9-6UC3-MountColor-Temp 6" x 1-1/4" x 1/2" 3W 27K, 30K40K, 50K 270

SG9-12UC6-MountColor-Temp 12" x 1-1/4" x 1/2" 6W 27K, 30K40K, 50K 540

SG9-18UC9-MountColor-Temp 17-7/8" x 1-1/4" x 1/2" 9W 27K, 30K40K, 50K 810






Installation Components

1 ¼"

WireWay Section

PART NUMBER DESCRIPTIONSP-20FT-18/2 20 foot spool of 18/2 awg solid wire

SP-50FT-18/2 50 foot spool of 18/2 awg solid wire

SG9-WW-48-Color 48" Field Cuttable WireWay

SG9-WW-MJ12-Color Miter joint - 45º cuts (2) 12-inch pieces

SG9-IL-CONN In-line Connector

• 50,000 hour LED life at 70% lumen maintenance• Concealed wire management with hidden

poke-home connectors• Frosted, light-diffusing lens• Streamlined from WireWay to light• 3-year limited warranty • No UV or IR• Dimmable (with compatible dimmer)

Features

• Under Cabinet Lighting• Cove Lighting• Display Lighting

Applications


RPVC (mount), extruded aluminum (heatsink), IR Acrylic (lens)



CRI: 90+


LED Spacing: 1-1/2"


Input Voltage: 15 Volt DC

Mounting: Screws (included)

Max Run: Refer to driver specs

Wiring: 18/2 solid (recommended)

Environment: Dry and damp locationsTask Light ing retains the r ight to modify the design of our products without pr ior not ice

Mounting Bracket Colors

Specifications

1/2"

1-1/4"Fixture Section

1/2"

1-1/4"

Power Supplies

*Call for dimming options


WireWay Colors





*WS-LED-CVD-902 Sempria dimming module for wireless system


20 800.445.6404 • TaskLighting.com

PRE-WIRINGRun separate wire from Driver (15 Volt DC) location to each zone. When total wattage of Sempria® LED fixtures in zone exceeds 75 Watts, use a second driver and run additional 18/2 solid wire for another zone. Length of wire from driver to first fixture in each zone is not to exceed 30 feet. Wiring may start at either end of fixture. (Option: separate wire may be run from driver to each fixture.)

DRIVER (15 Volt DC) LOCATIONS • Some Drivers may be conveniently concealed within our TR Series Angle Power Strip or Lighted Power Strip. • A sink base or the top of a cabinet are other common driver locations. • Driver must be accessible. • DO NOT LOCATE DRIVER IN ATTIC.

GENERAL GUIDELINES • A 15 VOLT DC DRIVER MUST BE USED WITH SEMPRIA® FIXTURES! Driver must be 15 Volt DC supplied by Task Lighting only!*

• All wiring must meet NEC® or local codes.

• 18/2 solid wire is recommended from driver to fixtures and between fixtures. (If 18/2 solid wire is not available, 18/2 stranded wire may also be used. Tin ends of wire if possible.)

• A maximum of 75 Watts of Sempria® LED Lighting is allowed on a zone.

• Limit wire length to 30 feet from driver to lights.

• Place switches on the 120 Volt side of the Driver (15 Volt DC).

• De-burr all cut WireWay edges to ensure wire safety.

• If other than Task specified dimmers are desired, call Task Lighting for instructions.

• Improper installation or applying improper voltage to fixture will void warranty. See TaskLighting.com for full warranty info.

light

WireWay

SG9-INSTALL-0618

1 ¼"

WireWay Section

1/2"

1-1/4"Fixture Section

1/2"

1-1/4”

SG9 SeriesInstallation Instructions


1. Cut SG9-WW WireWay Base the length from wire entry location (at back of cabinet) to the front of cabinet. Miter the corner or use SG9-WW-MJ12 (12” miter piece) to turn the corner. Deburr all cut edges to ensure wire safety.

2. Cut WireWay Base to fit full length of cabinet face. Deburr cut edges. Using screws provided, secure Base to bottom of cabinet every 12”. (When wiring between adjacent cabinets, drill 1/4” hole through end panels.)

3. Strip 1/4” insulation from driver wires. Push RED solid wire straight into terminal block with RED mark. Push BLACK solid wire straight into terminal block with BLACK mark. (18/2 solid wire is recommended. If using 18/2 stranded wire, ends must be tinned. Depress terminal block tab with ball point pen and insert wire.)

4. Cut wire to fit between adjacent fixtures. Insert wires into terminal blocks, maintaining polarity (RED wire to RED terminal, BLACK wire to BLACK terminal.) Maintain polarity or fixtures will not work.

5. Snap lens onto fixture. Position fixture in center of cabinet and snap into WireWay Base.

6. Cut WireWay Cover (or miter piece) to fit exposed Base. Deburr cut WireWay edges. Snap into Base.

OPTION: Installing Sempria® Fixtures Without WireWay

SG9-INSTALL-0618

Use mounting channel supplies with fixture. Use screws provided to secure mounting channel to underside at face of cabinet. Follow step 3 instructions. Position fixture in channel and snap into place.

SG9 SeriesInstallation Instructions


A SeriesLinear LED fixture with Angled Housing and a slim profile for multiple applications

PART NUMBER DIMENSIONS

TOTAL WATTS

KELVIN TEMP



FLAT HOUSING ⅛ WATTSA9Q-6UN2-Temp 6-1/2" x 1/2" x 5/8" 2W 27K, 30K

40K, 50K 207

SA9Q-12UN4-Temp 12-1/2" x 1/2" x 5/8" 4W 27K, 30K40K, 50K 414







SA9E-6UN1-Temp 6-1/2" x 1/2" x 5/8" 1W 27K, 30K40K, 50K 87








• Toe/Soffit Lighting• Cove Lighting• Interior Cabinet Lighting• Display Case Lighting

• 50,000 hour LED life at 70% lumen maintenance• Compact and versatile• Frosted lens• Poke-home connectors for easy installation• 3 Year limited warranty• No special gap-connectors needed• No UV or IR• Dimmable (with compatible dimmer)

S-A-SERIES-SPEC-0618


Installation Components PART NUMBER DESCRIPTIONSP-20FT-18/2 20 foot spool of 18/2 awg solid wire


SF9-WW-48 48" Sempria® LED Universal WireWayfor FLAT HOUSING


Applications

Features

Construction Materials: Extruded aluminum (heatsink), IR Acrylic (lens)

Wattage: 1/8 and 1/4 Watt LEDs


CRI: 90+


LED Spacing: 1-1/2"



Mounting: Double Stick Tape / Screws included



Environment: Dry and damp locations

Specifications

Power Supplies PART NUMBER DESCRIPTION/ OUTPUT INPUTTLD-24WSI* 24W plug in 15V DC Plug In

TLD-D30WSO 30W hardwire 15V DC, 2A max. 120V AC, .3ATLD-D45WSO 45W hardwire 15V DC, 3A max. 120V AC, .4ATLD-D60WSO 60W hardwire 15V DC, 4A max. 120V AC, .5ATLD-D75WSO 75W hardwire 15V DC, 5A max. 120V AC, .6A*Call for dimming options

Angled Housing








Low Light Output - 1/8 wattsection

5/8"

1/2"

1/2"


F SeriesLinear LED fixture with Flat Housing and a slim profile for multiple applications

PART NUMBER DESCRIPTION/ OUTPUT INPUTTLD-24WSI* 24W plug in 15V DC Plug In

TLD-D30WSO 30W hardwire 15V DC, 2A max. 120V AC, .3ATLD-D45WSO 45W hardwire 15V DC, 3A max. 120V AC, .4ATLD-D60WSO 60W hardwire 15V DC, 4A max. 120V AC, .5ATLD-D75WSO 75W hardwire 15V DC, 5A max. 120V AC, .6A

PART NUMBER DIMENSIONS

TOTAL WATTS

KELVIN TEMP



SF9Q-6UN2-Temp 6-1/2" x 1/2" x 1/2" 2W 27K, 30K40K, 50K 207








SF9E-6UN1-Temp 6-1/2" x 1/2" x 1/2" 1W 27K, 30K40K, 50K 87








• Toe/Soffit Lighting• Cove Lighting• Interior Cabinet Lighting• Under Cabinet Lighting• Display Case Lighting

Applications

• 50,000 hour LED life at 70% lumen maintenance• Compact and versatile• Frosted lens• Poke-home connectors for easy installation• 3 Year limited warranty• No special gap-connectors needed• No UV or IR• Dimmable (with compatible dimmer)

Features

S-F-SERIES-SPEC-0618




SF9-WW-48 48" Sempria® LED Universal WireWayfor FLAT HOUSING


Construction Materials: Extruded aluminum (heatsink), IR Acrylic (lens)

Wattage: 1/8 and 1/4 Watt LEDs


CRI: 90+


LED Spacing: 1-1/2"



Mounting: Double Stick Tape / Screws included




Specifications

Power Supplies

*Call for dimming options

Flat Housing


Low Light Output - 1/8 watt







section

3/8"

1/2"

1/2"


PRE-WIRINGRun separate wire from Driver (15 Volt DC) location to each zone. When total wattage of Sempria® LED fixtures in zone exceeds 75 Watts, use a second driver and run additional 18/2 solid wire for additional zone. Length of wire from driver to first fixture in each zone is not to exceed 30 feet. Wiring may start at either end of fixture. (Option: separate wire may be run from driver to each fixture.)

• Some Drivers may be conveniently concealed within our TR Series Angle Power Strip or Lighted Power Strip.• A sink base or the top of a cabinet are other common driver locations.• Driver must be accessible.• DO NOT LOCATE DRIVER IN ATTIC.

• A 15 VOLT DC DRIVER MUST BE USED! Driver must be 15 volt DC supplied by Task Lighting only!*

• All wiring must meet NEC® or local codes.

• 18/2 solid wire is recommended from driver to fixtures and between fixtures. (If 18/2 solid wire is not available, 18/2 stranded wire may also be used. Tin ends of wire if possible.)

• A maximum of 75 Watts of Sempria® LED Lighting is allowed on a zone.

• Limit wire length to 30 feet from driver to lights.

• Place switches on the 120 Volt side of the Driver.

• De-burr all WireWay edges to ensure wire safety.

• If other than Task specified dimmers are desired, call Task Lighting for instructions.

• Improper installation or applying improper voltage to fixture will void warranty. See TaskLighting.com for full warranty info.

GENERAL GUIDELINES

S-A&F-SERIES-INSTALL-0618

DRIVER (15 volt DC) LOCATIONS

section

3/8"

1/2"

1/2"

section

5/8"1/2"

1/2"

A & F SeriesInstallation Instructions


DD

$

Driver #1

15vDC

120V Switch

Driver #2

Start both sets of wires from drivers at a common point and wire the zones in opposite directions.

NOTE:If using stranded wire we recommend tinning the end of the wire first. If stranded wire is used without tinning, terminal block tabs must be depressed when inserting wires. Note that wiring with untinned stranded wire may result in a poor connection.

S-A&F-SERIES-INSTALL-0618

INSTALLING FIXTURES

1. Slide lens back to expose connectors or remove lens from fixture.

2. Strip 1/4" from RED wire and insert into terminal block opening with RED marking. Strip BLACK wire, insert into terminal block opening with BLACK mark. (If using 18/2 stranded wire, ends must be tinned. Depress terminal block tab with ball point pen and insert wire.)

3. Cut wires to fit between adjacent fixtures. Insert wires into terminal blocks, maintaining polarity (RED wire to RED terminal, BLACK wire to BLACK terminal.) MAINTAIN POLARITY OR THE FIXTURE WILL NOT WORK.

4. If fixture does not light, reverse wires.

5. Mounting surface must be finished and dust-free for mounting tape to properly adhere. Remove backing from mounting tape and press fixture firmly into place.

6. Using screws provided, secure fixture in place. DO NOT pierce LED strip with screws, nails, staples, or any other mechanical device.

7. Slide or snap lens back into place.

WHEN USING TWO DRIVERS:

A & F SeriesInstallation Instructions


R SeriesLinear LED Recessed fixture


PART NUMBER DIMENSIONSTOTAL WATTS

KELVIN TEMP



SR9E-8UN1-Temp 7-5/8" x 5/8" x 1/2" 1W 27K, 30K40K, 50K 87










KELVIN TEMP



SR9Q-8UN2-Temp 7-5/8" x 5/8" x 1/2" 2W 27K, 30K40K, 50K 207









KELVIN TEMP



SR9H-8UN3-Temp 7-5/8" x 5/8" x 1/2" 3W 27K, 30K40K, 50K 270








• Under Cabinet• Interior Cabinet• Floating Shelves• Fixed Shelves• Closet

Applications

• Design for recessed flush mounting• 50,000 hour LED life at 70% lumen maintenance• Compact and versatile• Frosted lens• Poke-Home™ connectors for easy installation• 3 Year limited warranty• No special gap-connectors needed• No UV or IR• Dimmable (with compatible dimmer)

Features


Anodized extruded aluminum (heatsink), IR Acrylic (lens)

Wattage: 1/8 Watt, 1/4 Watt, 1/2 Watt LEDs


CRI: 90+


LED Spacing: 1-1/2"



Mounting: Double Stick Tape / Screws (included)




Dimming OptionsPART NUMBER DESCRIPTIONDVELV-300P 300W Diva slide dimmerDVELV-303P 300W Diva slide dimmer 3-wayMAELV-600-Color Maestro electronic smart dimmerMA-R-Color Maestro companion dimmer*WS-LED-CVD-902 Sempria dimming module for wireless system


Installation Components PART NUMBER DESCRIPTIONSP-20FT-18/2 20 foot spool of 18/2 awg solid wireSP-50FT-18/2 50 foot spool of 18/2 awg solid wireSR9-EC-KIT End Cap Kit -Wire entry openings-Light Gray Only


Power Supplies

Section

S-R-SERIES-SPEC-0618

7/16"

5/8"

7/8"

1/2"

Specifications

PART NUMBER DESCRIPTION/ OUTPUT INPUTTLD-24WSI* 24W plug in 15V DC Plug InTLD-D30WSO 30W hardwire 15V DC, 2A max. 120V AC, .3ATLD-D45WSO 45W hardwire 15V DC, 3A max. 120V AC, .4ATLD-D60WSO 60W hardwire 15V DC, 4A max. 120V AC, .5ATLD-D75WSO 75W hardwire 15V DC, 5A max. 120V AC, .6A*Call for dimming options





R SeriesInstallation in Solid Bottom

S-R-SERIES-INSTALL-0618

GENERAL GUIDELINES• All wiring must meet NEC or local codes.• 18/2 solid wire is strongly recommended, from driver to fixtures, and between fixtures.• Wire length is maximum of 30 feet from driver to fixtures.• Maximum of 75 Watts of Sempria LED lighting is allowed per zone.• Place switches on the 120V side of driver.• If other than Task specified dimmers are desired, call Task Lighting for instructions.• Improper installation or applying improper voltage to fixture will void warranty. See TaskLighting.com for full warranty info.

DRIVERS• 15 VOLT DC DRIVER, supplied by Task Lighting only, must be used.• Driver must be accessible; the sink base or top of cabinet are common locations. • Do not locate driver in attic.• Some drivers may be concealed within our TR Series Angle Power Strip or Lighted Power Strip.

PRE-WIRING Run separate wire from Driver location to each zone. If total wattage of Sempria LED fixtures in zone exceeds 75 Watts, use

a second driver and run additional 18/2 solid wire for additional zone. When using two drivers, start both sets of wires from a common point and wire the zones in opposite directions. Wiring may start at either end of fixture. (Option: separate wire may be run from driver to each fixture.)

INSTALLATION1. Using a 5/8” router bit, hollow out a groove (the length of the fixture) from cabinet or shelf bottom.2. Remove lens from fixture.3. Strip 1/4” insulation from 18/2 wires that run from driver. Insert wires into terminal block at either end of fixture (RED wire to

terminal with RED mark, BLACK wire to terminal with BLACK mark.)4. Apply double stick tape (provided) to back of fixture and insert into groove. Fixture will fit tight. Secure fixture with screws

(provided). 5. Snap lens back in place.

If using end caps, please refer to the end cap instructions.

Backsplash

Counter Top

Bottom Shelf of Cabinet

Backsplash

Counter Top



R SeriesInstallation in Flush Panel Bottom

S-R-SERIES-INSTALL-0618





INSTALLATION1. Using a 5/8” router bit, hollow out a groove (the length of fixture) from flush panel.2. Remove lens from fixture.3. Strip 1/4" insulation from 18/2 solid wires that run from driver. Insert wires into terminal block at either end of fixture (RED wire

to terminal with RED mark, BLACK wire to terminal with BLACK mark.)4. Snap lens back onto fixture.5. Insert fixture into routed groove (fixture will fit tightly.)6. If needed use a silicone adhesive, spot-secure fixture to panel from top-side.7. Attach flush panel to bottom of cabinet.

If using end caps, please refer to the end cap instructions.

Counter Top


¼" Finished Panel


S SeriesLinear LED fixture with slim profile

PARTNUMBER DIMENSIONS

TOTAL WATTS

KELVIN TEMP



SS9E-6UN1-Temp 6-1/2" x 3/4" x 11/16" 1W 27K, 30K40K, 50K 87








PARTNUMBER DIMENSIONS

TOTAL WATTS

KELVIN TEMP



SS9Q-6UN2-Temp 6-1/2" x 3/4" x 11/16" 2W 27K, 30K40K, 50K 207









KELVIN TEMP



SS9H-6UN3-Temp 6-1/2" x 3/4" x 11/16" 3W 27K, 30K40K, 50K 270






SS9H-42UN21-Temp 42-1/2" x 3/4" x 11/16" 21W 27K, 30K 40K, 50K 1890

SS9H-48UN24-Temp 48-1/2" x 3/4" x 11/16" 24W 27K, 30K 40K, 50K 2160• Toe/Soffit Lighting

• Cove Lighting• Interior Cabinet Lighting• Display Case Lighting• Stair Lighting

Applications

• Built in light valance with light shield• 50,000 hour LED life at 70% lumen maintenance• Compact and versatile• Frosted lens• Poke-Home™ connectors for easy installation• 3 Year limited warranty• No special gap-connectors needed• No UV or IR

• Dimmable (with compatible dimmer)

Features


Anodized extruded aluminum (heatsink), IR Acrylic (lens)

Wattage: 1/8 Watt, 1/4 Watt, 1/2 Watt LEDs


CRI: 90+


LED Spacing: 1-1/2"



Mounting: Double Stick Tape / Screws (included)




S-S-SERIES-SPEC-0618


Installation Components PART NUMBER DESCRIPTIONSP-20FT-18/2 20 foot spool of 18/2 awg solid wireSP-50FT-18/2 50 foot spool of 18/2 awg solid wireSG9-IL-CONN In-line ConnectorSS9-WW-48 48” Sempria® LED WireWay for S Series

Section

3/4"

7/8"11/16"

Specifications




Hight Light Output - 1/2 watt


Dimming OptionsPART NUMBER DESCRIPTIONDVELV-300P 300W Diva slide dimmerDVELV-303P 300W Diva slide dimmer 3-wayMAELV-600-Color Maestro electronic smart dimmerMA-R-Color Maestro companion dimmer*WS-LED-CVD-902 Sempria dimming module for wireless system



S SeriesInstallation Instructions

S-S-SERIES-INSTALL-0618

DD

$

Driver #1

15vDC

120V Switch

Driver #2Start both sets of wires from drivers at a common point and wire the zones in opposite directions.

WHEN USING TWO DRIVERS:





INSTALLATION1. Remove lens from fixture. 2. Select side of fixture that will attach to mounting surface. Using 1/8” bit, drill two mounting holes one near each end of fixture

(location is indicated by BLACK mark on end of fixture.) DO NOT pierce or damage LED board. Deburr metal. 3. Apply foam double-stick tape squares to same side of fixture, avoiding the mounting holes. 4. Strip ¼” from RED 18/2 solid wire; push wire straight into terminal block opening with RED mark. Strip BLACK 18/2 solid wire;

push wire straight into terminal block opening with BLACK mark. (If using 18/2 stranded wire, ends must be tinned. Depress terminal block tab with ball point pen and insert wire.)5. Cut wires to fit between adjacent fixtures. Insert wires into terminal blocks, maintaining polarity (RED wire to RED terminal,

BLACK wire to BLACK terminal.)6. If fixture does not light, reverse wires. Gently depress terminal block tab and carefully pull wires straight out. 7. Mounting surface must be finished and dust/residue free. Peel backing from tape squares and press firmly into place.8. Using screws provided, secure fixture in place. DO NOT pierce LED strip with screws, nails, staples or any other mechanical

device.9. Snap lens back into place.

31800.445.6404 • TaskLighting.comS-S-SERIES-INSTALL-0618

Stairs Cove Soffit-Above Cabinet

Window Sill

Deck Rail

Toe Kick

window

backsplash

Interior Cabinet-Vertical

top view

shelf

S SeriesMounting Positions ‒ Not to Scale


Lighted Closet RodIlluminated LED Lighted Closet Rod

PART NUMBER LENGTH WATTS KELVIN TEMP



LC9R18-4-P-Finish-Temp 18" 4 27K, 30K, 40K, 50K 621 LC9R24-6-P-Finish-Temp 24" 6 27K, 30K, 40K, 50K 828 LC9R30-8-P-Finish-Temp 30" 8 27K, 30K, 40K, 50K 1035 LC9R36-10-P-Finish-Temp 36" 10 27K, 30K, 40K, 50K 1242 LC9R42-12-P-Finish-Temp 42" 12 27K, 30K, 40K, 50K 1449 LC9R48-14-P-Finish-Temp 48" 14 27K, 30K, 40K, 50K 1656 LC9R54-16-P-Finish-Temp 54" 16 27K, 30K, 40K, 50K 1863 LC9R60-18-P-Finish-Temp 60" 18 27K, 30K, 40K, 50K 2070 LC9R66-20-P-Finish-Temp 66" 20 27K, 30K, 40K, 50K 2277 LC9R72-22-P-Finish-Temp 72" 22 27K, 30K, 40K, 50K 2484 LC9R78-24-P-Finish-Temp 78" 24 27K, 30K, 40K, 50K 2691 LC9R84-26-P-Finish-Temp 84" 26 27K, 30K, 40K, 50K 2898 LC9R90-28-P-Finish-Temp 90" 28 27K, 30K, 40K, 50K 3105 LC9R96-30-P-Finish-Temp 96" 30 27K, 30K, 40K, 50K 3312

Flange set included with each closet rod

PART NUMBERS

Finish Options

Installation Components

LIGHTEDCLOSETROD-SPEC-0618

PART NUMBER DESCRIPTIONSP-20FT-18/2 20 foot spool of 18/2 awg solid wireSP-50FT-18/2 50 foot spool of 18/2 awg solid wire

MCS-10-Color 10W Max - Magnetic Contact Switch. Available in Brown, Gray, or White

MCS-100-Color 100W Max - Magnetic Contact Switch.Available in Brown, Gray, or White

MS-OPS5M-Color 5 Amp - Maestro Occupancy Sensor SwitchMS-VPS5M-Color 5 Amp - Maestro Vacancy Sensor Switch

Fixture Section

1-1/8"

1-1/4"

1-1/2"

3-3/8"

15/16"

Flange Section

TASK LIGHTING

MATERIAL

DATE

DATEREV

REVISIONS

CHECKED

APPROVEDDESCRIPTION

SIZE

ZONE

DRAWN A

REV DATE

Dimensions are in inches

TASK LIGHTING

MATERIAL

DATE

DATEREV

REVISIONS

CHECKED

APPROVEDDESCRIPTION

SIZE

ZONE

DRAWN A

REV DATE

Dimensions are in inches

1" Wide11-7/8"

10-7/8"

3"

Center Bracket Support Section

2-1/2"

• 50,000 hour LED life at 70% lumen maintenance• Each end field trimmable up to 3"• 15V DC plug-in or hardwire drivers (ordered separately)• Accessories sold separately: Center Bracket Support• No UV or IR

Features

PART NUMBER DESCRIPTION

LC9R-CBS-P-Finish Center Bracket Support (Use every 4' for fixtures over 48")

Accessories

• Closet Lighting• Laundry Room Lighting

Applications

Specifications


Dimensions: 18" - 96" L x 1-1/2" W x 1-1/4" H

Construction Materials: Extruded aluminum-Powder Coat Finish



CRI: 90+


LED Spacing: 1-1/2”LED Board: 6" or 12"Input Voltage: 15 Volt DCMounting: Flange set and center bracketsMax Run: Refer to driver specsWiring: 18/2 solid (recommended)Environment: Dry and wet locations

Flange SetPART NUMBER DESCRIPTIONLC9R-FS-P-BK LED Closet Rod Flange Set-BlackLC9R-FS-P-BZ LED Closet Rod Flange Set-BronzeLC9R-FS-P-SN LED Closet Rod Flange Set-Satin NickelLC9R-FS-P-WT LED Closet Rod Flange Set-White






1. Rod and lens must be 3/8” shorter than closet width measurement.

2. If field-trimming is necessary, slide lens out of fixture. Use scissors or shears to trim lens to length (3/8” shorter than closet width.)

7. Holding rod, lens, and loose flange in one hand, push RED solid wire push straight into LED terminal block opening with RED mark. Push BLACK solid wire straight into terminal with BLACK mark. (18/2 solid wire is recommended. If using 18/2 stranded wire, ends must be tinned. Depress terminal block tab with ball point pen and insert wire.”

3. Use chop or hacksaw to cut rod to proper length. DO NOT CUT LED CIRCUIT BOARD. Deburr all cut edges. Slide lens back into place.

5. Using #8 ( 1 1/2”) wood screws provided, secure one flange to wall stud on “non-wired” side of closet.

6. Slide second flange onto rod with grooved side facing opposite wall.

8. Insert “non-wired” side of rod into installed flange.

NOTE: Maintain wire polarity. If fixture does not illuminate after making wire connections, reverse wires at driver. (A slight delay "on" is possible.)

9. Partially fasten second flange to wall using ONE screw. Carefully position wires into one of the groves located on back of flange. Secure flange to wall with remaining screw, making sure wire is in flange groove. (If wires come through drywall and into the fixture, this step is not needed.)

LIGHTEDCLOSETROD-SPEC-0618

4. Prep wires for LED fixture: Strip 1/4” of insulation from RED and BLACK wires.

0. Push rod against wall in “non-wired” flange and tighten set screw.

1

1. Cut Sempria WireWay to cover wires from flange exit to driver. Remove cover of WireWay and secure mounting base (wider piece) to wall with screws provided. Position wires inside base and snap cover (smaller piece) into place. Deburr all cut WireWay edges to protect wire insulation.

1

Lighted Closet RodInstallation Instructions


PuckLED Lighting with a slim profile for multiple applications

PART NUMBER KELVIN TEMPLUMENSBased on 3000K


SPL9-FR-P-Finish-Temp 2700K, 3000K 210

Specifications

Features


Dimensions: 2-1/4" x 2-1/4" diameter, 2" cut-out

Construction Materials: Cast Aluminum (heatsink), frosted glass

Wattage: 4 Watts

Color Temp (Kelvin): 2700K (Warm White) or 3000K (Soft White)

CRI: 85+




Wiring: 6 ft. Lead Wire Included


SEMPRIA-PUCK-SPEC-0618

Housing Section

Fixture Section

Cutout

Finish Options

• Interior Cabinet Lighting• Under Cabinet Lighting• Display/Accent Lighting

Applications

2 1/4"

5/16"

5/8"



• 50,000 hour LED life at 70% lumen maintenance• Surface or recess mount• Frosted, light-diffusing lens• 4 Watts per fixture• 3-year limited warranty • No UV or IR• Dimmable (with compatible dimmer)

Not recommended for sheetrock installation.

1 7/8"



Puck Lights






*WS-SR-Color-902Sempria wireless dimmer switch. Available in Black, Gray, Ivory, Light Almond, and White**NOTE: Call TASK for alternate driver


35800.445.6404 • TaskLighting.comSEMPRIA-MINICAN-SPEC-0618

Fixture Section

2"

3/4"

1"

Beam Spread Chart

Housing Section Cutout

2 1/4"

2"

Mini CanLED Lighting with a slim profile for multiple applications

PART NUMBER BEAM SPREAD KELVIN TEMPLUMENSBased on 3000K


SPMC-11-P-Finish-Temp 11º Spot 2700K, 3000K 240

SPMC-20-P-Finish-Temp 20º Narrow Flood 2700K, 3000K 240

SPMC-38-P-Finish-Temp 38º Flood 2700K, 3000K 240

Specifications


Dimensions: 2-1/4" x 2-1/4" diameter, 2" cut-out

Construction Materials: Cast Aluminum (heatsink)

Wattage: 4 Watts


CRI: 85+

Beam Angle: 11, 20, or 38 degree beam spread




Wiring: 6 ft. Lead Wire Included


Finish Options

• 50,000 hour LED life at 70% lumen maintenance• Surface or recess mount• 4 Watts per fixture• 3-year limited warranty • No UV or IR• Dimmable (with compatible dimmer)

Features

• Interior Cabinet Lighting• Display/Accent Lighting• Above Sink Lighting

Applications



Not recommended for sheetrock installation.



Mini Cans








36 800.445.6404 • TaskLighting.com S-PUCK/MINICAN-INSTALL-0618

Call Task Lighting if you have any questions or need assistance.

Determine exact location of fixtures and drill 2" diameter hole.

Run fixture wires through the hole and feed them in the direction of the driver.

1 Connect RED driver wire with RED fixture wire using wire nuts provided. Repeat process with BLACK wires, making sure all connections are tight.

2 Squeeze wing tabs on side of fixture.

3

All wiring must meet NEC® or local codes.The maximum wire length of the driver and fixture wire is 30 feet.Not recommended for sheetrock installation.

OPTIONAL: Surface Mounted Fixtures

Drawing shows wiring for two fixtures using wire nut connectors

Driver

Insert fixture into hole. 4

Run fixture wires through the hole and feed them in the direction of the driver. Secure housing to surface with two screws provided. Follow steps #2 - #4 above.

Puck/Mini CanInstallation Instructions


Supporting ProductsInstallation Components



DVELV-300PDVELV-303P

MAELV-600-Color MA-R-Color

TLD-D30WSOTLD-D45WSOTLD-D60WSOTLD-D75WSO

• Constant Voltage• Short circuit, over-load, voltage, and temperature protection• High reliability, high efficiency• UL listed Class 2 power supply

TLD-24WSI

PART NUMBER DESCRIPTIONMCS-10-BR 10W Max - Magnetic Contact Switch - BrownMCS-10-GR 10W Max - Magnetic Contact Switch - GrayMCS-10-WT 10W Max - Magnetic Contact Switch - WhiteMCS-100-BR 100W Max - Magnetic Contact Switch - BrownMCS-100-GR 100W Max - Magnetic Contact Switch - GrayMCS-100-WT 100W Max - Magnetic Contact Switch - White

Magnetic Contact Switch

Power Supplies PART NUMBER DESCRIPTION/ OUTPUT INPUT DIMENSIONS

TLD-24WSI* 24W plug in 15V DC Plug In 3-1/4� x 1-1/2� x 1-7/8�

TLD-D30WSO 30W hardwire 15V DC, 2A max. 120V AC, .3A 8-1/8� x 2� x 1-3/4�TLD-D45WSO 45W hardwire 15V DC, 3A max. 120V AC, .4A 8-1/8� x 2� x 1-3/4�TLD-D60WSO 60W hardwire 15V DC, 4A max. 120V AC, .5A 8-1/8� x 2� x 1-3/4�TLD-D75WSO 75W hardwire 15V DC, 5A max. 120V AC, .6A 8-1/8� x 2� x 1-3/4�*Call for dimming options







SEMPRIA-INSTALLATION-0618

1-7/16�

1-7/8�

3-1/4�

1-3/4�

8-1/8�

2�


120V Bar LightDirect wire, easy to install bar light

Linair 120V Bar Light

Optional Installation Components PART NUMBER DESCRIPTION320-C 3/8" Trade Romex clamp

Black Cord 6FT 6 ft. Hardwire power cord w/ ground. 18/3 SJB cord(for field installation only)

• Under Cabinet Lighting• Display Case Lighting• Over Sink Lighting

Applications


Dimming OptionsPART NUMBER DESCRIPTIONMACL-153M-COLOR Maestro LED DimmerMA-R-COLOR Preset Smart Remote (for multiple switching)

SpecificationsConstruction Materials: Extruded aluminum housing (heatsink), Impact

Resistant Acrylic (lens), Powder coat finish


CRI: 90+


LED Spacing: 3"

LED Board: 8-3/4"

Power Rating: 130 V AC Max, 50/60 HZ

Mounting: Wood Screws (included)

Wiring: 12-14 ga romex (3/8 Trade Romex, Clamp Included)


Finish Options

LINAIR-BARLIGHT-SPEC-0618

MACL-153M-COLOR

• 50,000 hr LED life at 70% lumen maintenance• Integral Driver• Easy open/close installation • Multiple knockout locations (6)• 3 Year limited warranty• No UV or IR• Dimmable (with compatible dimmer)

Features

Section

PART NUMBER LENGTH WATTS KELVINTEMP



LB9L10-5-P-Finish-Temp 10� x 4-1/4� x 1� 5 2700K 3000K 360

LB9L18-7-P-Finish-Temp 18-1/2� x 4-1/4� x 1� 7 2700K 3000K 720

LB9L27-11-P-Finish-Temp 27-1/4� x 4-1/4� x 1� 11 2700K 3000K 1080

LB9L36-15-P-Finish-Temp 36� x 4-1/4� x 1� 15 2700K 3000K 1440

1"

4-1/4"

1-1/4"3"

Satin Nickel (SN)Bronze (BZ) White (WT)

39800.445.6404 • TaskLighting.comLINAIR-BARLIGHT-INSTALL-0618

14/2 to 10/2

120 Volt (Black)

Neutral (White)

Ground Green

Figure 3Factory

Connection

Driver

Switch

Figure 2

Figure 1

Before installing, turn power off at main breaker panel.

Expose wiring compartment by inserting flat blade screwdriver between housing and cover; Gently pry down to open. (Figure 1)

Position fixture in mounting location to determine which knock-out to use.

Install supplied conduit connector into knock-out. Secure wire. Connector may be used with: 3/8 trade sized reduced wall flexible steel or aluminum conduit, 14/2 to 10/2 non-metallic sheathed cable, or 14/2 to 10/2 steel armored cable.

All installations must comply with national and local electrical codes.

Using orange push connector provided, connect WHITE to WHITE wire from driver. (Figure 3)

Using orange push connector provided, connect BLACK to BLACK wire from the 120V side of the fixture switch. (Figure 3)

Ensure all wires are pushed to inside of housing; snap cover shut.

Turn power on at main breaker panel.

Mount fixture with screws provided. (Figure 2)

Secure ground wire (GREEN) to PEM stud marked with on fixture

120V Bar LightInstallation Instructions

1206 M Avenue Kearney, NE 68847 • P: 800.445.6404 • F: 855.234.9401 • TaskLighting.comSPEC&INSTALL-V1.1-0618

Specifications & Installation Instructions

specifications & installation instructions...specifications & installation instructions 1206...

Documents