specification sheet lumenbeam - lumenpulse.com · f - power and data output to fixture (wiring by...

LARGECOLOR CHANGING

GS - R29

1/8

2017.03.30

Specification Sheet lumenbeam™

5-year limited warranty.

Consult www.lumenpulsegroup.com for our complete Standard Terms and Conditions of Sales.

© Copyright Lumenpulse 2017

1751 Richardson, Suite 1505 Montreal (Quebec) Canada H3K 1G6

1.877.937.3003 P.514.937.3003 F. [email protected]

Lumenpulse reserves the right to make changes to this product at any time without prior notice and such modi�cation shall be effective immediately.

0°

90°

160°

70°

Standard Yoke MountingAdjustable pivot limits

Standard Yoke (as shown, included)

4 34 "

14 78

"

10"

[378mm]

[257mm]

[254mm]

10 18

"

[121mm]

Client Project name

Order# Type Qty

FEATURES AND BENEFITS

Physical :• Low copper content high pressure die-cast aluminum housing• Heavy aluminum formed yoke (standard yoke included)• Stainless steel hardware• Silicone sealing devices• Clear tempered glass lens• Dual chamber design for heat management and ease of maintenance• Electro-statically applied polyester powder coat finish• 5.44 kg / 12 lbs• EPA: Front = 0.94 sq. ft. / 0.087 sq. m. Side = 0.56 sq. ft./ 0.052 sq. m.• IP66• IK10 rated• Meets 3G ANSI C136.31 Vibration standard for bridge applications• Corrosion-resistant coating for hostile environments*

Performance :• 1,795 delivered lumens and 72,904 candelas at nadir (RGB full output, 6° optic)• 2,233 delivered lumens and 93,100 candelas at nadir (RGBW full output, 6° optic)• 1,690 delivered lumens and 66,141 candelas at nadir (RGBA full output, 6° optic)• Color mixing options: RGB (3 channels), RGBW or RGBA (4 channels)• 6°, 10°, 20°, 40° or 60° optics available• Lumen maintenance 120,000 hrs [L70 @ 25°C]• Lumen measurements comply with LM - 79 - 08 standard• Operating temperatures: -25° C to 50° C [-13F to 122F]

Electrical :• Line voltage luminaire for 100 to 277V• Power and data in 1 cable, 3ft/1m cord standard (#16-5), other lengths available• 50 watts• Control options: Lumentalk or DMX/RDM enabled

* Use only when exposed to salt spray and harsh chemicals. This option is not required for normal outdoor exposure!

IK10

DeliveredOutput [lm]

Photometric Summary(RGBW color mix, full output)

Intensity[peak cd]

VN 2,233 93,100

NS 1,767* 60,125*

1,631* 11,977*NF

FL 1,642* 4,543*

Photometric performance is measured incompliance with IESNA LM-79-08.

*Estimated. Consult Lumenpulse websitefor the latest IES and LDT files.

WFL 1,600* 1,513*

LARGECOLOR CHANGING

GS - R29

2/8

2017.03.30








MOUNTING OPTION

SYShort Yoke Mounting

Short Yoke mountingadjustable pivot limits

0°

45°

109°

33°

Standard and Short Yoke mountingholes Pattern

3"[76mm]

[11mm]

716 "

516 "

8mm

434

"

10 18

"

11 14

" 10"[254mm]

[121mm]

[257mm]

[286mm]

OPTICAL OPTIONS*Factory installed

LSLHLinear Spread Lens

Horizontal distribution(not adjustable on site)

LSLVLinear Spread LensVertical distribution

(not adjustable on site)

Factory installed, available for VN to FL optics .See Optical Accessories for field adjustable spread lens.

LARGECOLOR CHANGING

GS - R29

3/8

2017.03.30








PM4-1, PM4.5-1, PM5-1Round Pole Mounting accessory

single fixture

PM4-2, PM4.5-2, PM5-2 Round Pole Mounting accessory

twin fixtures

When PM4-2, PM4.5-2 or PM5-2 are specified,one bracket assembly is supplied per 2 fixtures unless

otherwise specified.

Mounting Accessories

PM4 Round Pole Mounting Accessory Shown*Consult factory for square pole section

16 20 1 "

[509mm]

5 18

"[131mm]

7 516

"[185mm]

2 316"

[55mm]

TN4Tenon adapter

to fit on 4” O.D. tenon

TN2Tenon adapter

to fit on 2 3/8” O.D. tenon

"212

4"[102mm]

[105mm]

4"[102mm]

[64mm]

418

"

578 "

[149mm]

[149mm]57

8"

For pole Ø 4"± 1/16" 4.5"± 1/16" 5" ± 1/16"

PM4 PM4.5 PM5

*Consult factory for other pole diameters.

101.6 mm± 1.6mm 114.3mm ± 1.6mm 127mm ± 1.6mm

ACCESSORIESOrder separately

LARGECOLOR CHANGING

GS - R29

4/8

2017.03.30








Optical Accessories:LBL-SN-___-BK Snoot accessory. Please specify desired exterior finish from the list below.

Interior surface painted black.

LBL-SNW-___-BK Snoot Wide accessory. Please specify desired exterior finish from the list below.Interior surface painted black.

LBL-VS-___-BK Visor accessory. Please specify desired exterior finish from the list below.Interior surface painted black.

LBL-WG-___ Wire Guard accessory. Please specify desired exterior finish from the list below.

LBL-LSLA-___ Linear Spread Lens Adjustable accessory. Please specify desired exterior finish from the list below.

Available finishes:BK - Black SandtexBRZ - Bronze SandtexSI - Silver SandtexWH - Smooth white, low glossBKTX - Textured blackBRZTX - Textured bronze, non-metallicGRATX - Textured medium grayGRNTX - Textured greenWHTX - Textured whiteCC - Custom color and finish (please specify RAL color)1

Accessory combinations: Snoot+

Linear SpreadLens Adjustable

Visor

Wire Guard

YES

YES NO

Snoot Wide

YES YES

YES

Accessory combinations must be ordered together on a single line.Ex: A Snoot + Wire Guard combination order code is LBL-SNWG-BK-BK.

Notes:1 North American RAL colors specified with RAL number only are provided with a smooth/high-gloss finish. Please consult factory for other RAL textures and glosses, or to match alternate colorcharts. Final color matching results may vary.

ACCESSORIES - continuedOrder separately. Note: installed optical accessories will affect the maximum pivot limits for each mounting option, consult factory for details.

LARGECOLOR CHANGING

GS - R29

5/8

2017.03.30








ACCESSORIES - continuedOrder separately

Control Systems:LTO2 Lumentouch is a wall mount DMX 512 controller keypad.

LCU Lumencue is a USB / mini SD DMX 512 controller.

LID LumenID is a diagnostic and addressing DMX 512 controller.It must be specifi ed on all DMX applications.Refer to LID specifi cation sheet for details.

LID-LT LumentalkID is a diagnostic and addressing controller.It must be specifi ed for all Lumentalk (LT) applications.Refer to LID-LT specifi cation sheet for details.

LTN Lumentone is a simple pre-programmed DMX 512 controllerwith a push button rotary dial and live feedback.

Control Boxes:CBX DMX/RDM control box.

Up to six power and data outputs to fi xtures or fi xture runs.Ethernet enabled option.Refer to CBX specifi cation sheet for details.

LARGECOLOR CHANGING

GS - R29

6/8

2017.03.30








A - Third party DMX/RDM controllerB - Lumentranslator (LTL-DMX)C - Data wiring (by others)D - Power line (120-277V AC)E - Junction box (by others)F - Power wiring (by others)G - Lumenbeam Large (LBL-DMX)

B

E

A

DC F

G

Lumentalk (LT)

Notes: • Consult factory for specific applications and maximum fixture count/cable length recommendations.• Lumentalk enabled fixtures must be commissioned using LumentalkID software and a LID-LT. Consult factory for details.• Maximum of 1 transmitter (Lumentranslator or Lumenlink) per system.• No third party fixtures allowed on the same circuit.• 1 DMX controller per Lumentalk network, maximum of 48 DMX channels per Lumentalk network (minimum step transition update rate is 1 second, minimum fade time between two colors is 1 minute). Consult factory for applications that require additional capabilities. • 50 watts per fixture.

A - Power input (control over powerline via Lumentalk system) or from previous fixtureB - To fixtureC - To next fixtureD - LineE - GroundF - NeutralG - Wire-nuts (by others)H - Junction box (by others)

A

B

C

H

DEFG

Lumentalk (LT) - Wiring detail

Wiring Color CodeAmericanColor Code

CEColor Code

Black Brown

Red/Purple BlackOrange Grey

White Blue

USE

Live 100-277V

0-10V / Data +

Green Yellow/Green Ground

0-10V / Data -

Neutral

TYPICAL WIRING DIAGRAMS

LARGECOLOR CHANGING

GS - R29

7/8

2017.03.30








A - Third party DMX/RDM controllerB - Data input (Belden 9841 or equivalent, by others)C - Data output to next CBX (optional, not isolated/not boosted)D - CBX-STE - Power input (100-277V)F - Power and data output to fixture (wiring by others)G - Junction box (by others)H - Lumenbeam Large (LBL-DMX/RDM)

A - Third party DMX/RDM controllerB - Data input (Belden 9841 or equivalent, by others)C - Data output to next CBX (optional, not isolated/not boosted)D - CBX-DSE - Power input (100-277V)F - Power and data output to fixture (wiring by others)G - Junction box (by others)H - Lumenbeam Large (LBL-DMX/RDM)I - Power and data wiring (by others)

D

B

EC

F G

H

A

BA

EC D

F I

H

G

Configuration/Voltage 240V 277V

32 3250ft [15m] from CBX

120V

18

208V

28

Maximum number of fixtures per run(based on 15A maximum, 16AWG cable, fixtures

spaced 10ft [3m] on center, first fixture 50ft [15m] from CBX)

A

J

C

BED

FGH

I

A E

J

B

FGHI

DC

A - From CBX or previous fixtureB - Lumenterminator (use at the end of each run only)* C - To fixtureD - Data -E - Data +F - NeutralG - GroundH - LineI - Wire nuts (by others) J - Junction box (by others)

A - From CBX or previous fixtureB - To fixtureC - Data +D - Data -E - To next/from previous fixtureF - LineG - GroundH - NeutralI - Wire nuts (by others) J - Junction box (by others)

Wiring Color Code

Star Layout (DMX/RDM)

Daisy Chain Layout (DMX/RDM)

DMX/RDM - Wiring detail

DMX/RDM - Wiring detail (first or middle of run)

Notes: • Consult factory for specific applications and maximum fixture count/cable length recommendations.• Maximum of 32 DMX/RDM enabled fixtures per CBX output.• Maximum of 4 DMX/RDM repeaters/CBX cascading in line.• Maximum of 6 outputs per CBX-ST, maximum of 1output per CBX-DS.• Maximum 3ft [1m] fixture cable length recommended for daisy chain layout.• RGB color mixture option requires 3 DMX addresses. RGBW color mixture option requires 4 DMX addresses. RGBA color mixture option requires 4 DMX addresses.• 50 watts per fixture.

* DMX terminator is required at the end of each run to maintain data integrity. (2x) DMX lumenterminator included per CBX-DS, (6x) DMX lumenterminator included per CBX-ST. See installation instructions for details.

AmericanColor Code

CEColor Code

Black Brown

Red/Purple BlackOrange Grey

White Blue

USE

Live 100-277V

0-10V / Data +

Green Yellow/Green Ground

0-10V / Data -

Neutral

TYPICAL WIRING DIAGRAMS - continued

A

J

C

BED

FGH

I

A - From CBX or previous fixtureB - Lumenterminator* C - To fixtureD - Data -E - Data +F - NeutralG - GroundH - LineI - Wire nuts (by others) J - Junction box (by others)

DMX/RDM - Wiring detail (end of run)

LARGECOLOR CHANGING

GS - R29

8/8

2017.03.30








LBL 1 2 3 4 5 6 7 8 9

HOW TO ORDER

1 Housing:

LBL - Lumenbeam™ Large

2 Voltage:

100 - 100 volts120 - 120 volts208 - 208 volts

220 - 220 volts240 - 240 volts277 - 277 volts

3 Colors and Color temperatures:

RGB - Additive red, green and blueRGBW - Additive red, green, blue and white 4000KRGBA - Additive red, green, blue and amber

Consult factory for color mix with Royal Blue, 3000K or other white color temperature LEDs.

4 Optic:

VN - Very Narrow 6°

NS - Narrow Spot 10°

NF - Narrow Flood 20°

FL - Flood 40°

WFL - Wide Flood 60°

5 Optical Option:

LSLH - Linear Spread Lens Horizontal distribution1

LSLV - Linear Spread Lens Vertical distribution1

6 Finish:

BK - Black SandtexBRZ - Bronze SandtexSI - Silver SandtexWH - Smooth white, low glossBKTX - Textured blackBRZTX - Textured bronze, non-metallicGRATX - Textured medium grayGRNTX - Textured greenWHTX - Textured whiteCC - Custom color and finish (please specify RAL color)2

7 Control:

LT - Lumentalk3

DMX/RDM - DMX/RDM enabled4

8 Option:

SY - Short Yoke3GV - 3G ANSI C136.31 Vibration RatingCRC - Corrosion-resistant coating for hostile environmentsCE - CE (certification covers European Economic Area)

9 Cable Length:

3FT - 3ft (standard lengthunless otherwise specified)5

10FT - 10ft20FT - 20ft30FT - 30ft50FT - 50ft70FT - 70ft100FT - 100ft

1M - 1m (standard lengthunless otherwise specified)5

5M - 5m10M - 10m15M - 15m20M - 20m30M - 30m

Notes:1 Factory installed, available for VN (6°) to FL (40°) optics. See Optical Accessories for field adjustable spread lens. 2 North American RAL colors specified with RAL number only are providedwith a smooth/high-gloss finish. Please consult factory for other RAL textures and glosses, or to match alternate color charts. Final color matching results may vary. 3 Lumentalk enabled fixtures mustbe commissioned using LumentalkID software and a LID-LT. Consult factory for details. 4 Fixtures set to by fixture resolution (consult the Resolution Details page for the number of DMX addresses).5 Maximum 3ft [1m] fixture cable length recommended for daisy chain DMX applications with CBX-DS.

specification sheet lumenbeam - lumenpulse.com · f - power and data output to fixture (wiring by...

Documents