sostel - bed heads catalogue 2013

KABELseries

systems for a communicating world

®

ELECTROMEDICAL UNITS

BED HEADS

SOSTEL HAS BEEN PRESENT IN THE ITALIAN MARKET FOR OVER 30 YEARS AND PROPOSES ITSELF AS AN

IMPORTANT REFERENCE IN THE HEALTHCARE MARKET FOR INTERNAL COMMUNICATION SYSTEMS AND

BED HEAD UNITS.

Service-oriented, Sostel addresses its expertise and knowledge to its customers, to allow a better choice of:

Nurse Call, Paging, Intercom systems, and Electromedical bed head units.

Since 2000, the Company has been selling bed head units and, in 2001 decided to directly produce these

devices, while in 2005 it acquired the certifi cation, for the entire Kabel product line, as manufacturer of electrical

equipment conforming to Directive 93/42/EC – Annex II for medical devices.

Sostel boasts a commercial network that covers all of Italy and is able to assist its customers with professionalism,

understanding their needs and off ering advanced solutions; an expert technical department is able to ensure

maximum customer assistance, with commissioning of the systems and repairs in its well-equipped workshop.

2

INTRODUCTION

DESIGN IS SOSTEL’S BASE ACTIVITY FOR OFFERS AND PRODUCTION OF KABEL SERIES BED HEAD UNITS,

AND THEY ARE MADE TO CUSTOMER’S SPECIFICATIONS.

Through the appropriate use of technical standards, calculations, customer specifi cations and drawings the

necessary procedures for the production of the electrical equipment is defi ned.

Design is an activity that, thanks to a concentration of knowledge, actions, methodologies and tools, allows

Sostel to organize and produce solutions for the production of multiple models, currently more than 12, ranging

from a single channel for the passage of electric cables or gas pipes, to devices with direct and indirect lighting

and more complex units, up to the suspended ceiling units.

Using CAD systems, Sostel creates technical drawings that allow customers to decide in advance where to

place the various power sources and electrical components. The layout, approved and signed by the customer,

becomes Sostel’s only offi cial production document.

3

DESIGN

4

PRODUCTION

PRODUCTION IS THE SET OF OPERATIONS THROUGH WHICH GOODS ARE CREATED, PROCESSED AND /OR

MODIFIED, WITH THE USE OF PHYSICAL AND HUMAN RESOURCES, TO MAKE THEM APPROPRIATE TO MEET

THE NEEDS.

Interpreting this thought in its daily production, Sostel sets the goal of “delivering products that provide value

for the customer.”

At Sostel, the term production refers to product quality, an important parameter related to the cost, service and

value-added of the single person that works there.

The production cycle starts with the bed head unit layout, signed by the customer: various aluminum profi les

are processed, with the use of numerical control machines, then taken to the paint-shop, assembled and wired,

according to customer’s requirements.

Sostel is ISO 9001:2008/ISO 13485:2003 certifi ed and produces and tests the bed head units according to

Directive 93/42/EC, with certifi cation by IMQ , ensuring the complete reliability of the product.

5

CERTIFICATE

DESCRIPTION

The power supply units for the medical use of the KABEL

series, combine technical and functional solutions into one

unit in order to make the patient’s stay in the hospital more

comfortable.

Designed for hospitals, nursing homes, etc.,

KABEL series units exploit the modularity and fl exibility of

their components to meet the increasingly demanding

requirements of ergonomics and design, diff using light in

a proper and pleasant way.

The various distributed services: electrical, medical gases,

alarms, data transmission and diagnostics, are placed on

the front part of the bed head unit, easily accessible to both

the patient and the hospital staff and are well integrated in

the diff erent profi les, made with rounded forms to facilitate

cleaning and to prevent improper use as a base to support

objects and more.

All KABEL series units are composed of 2 mm-thick extruded aluminum profi les, anodized or painted with epoxy

powders in RAL colors or wood fi nish, depending on customer’s choice. The diff erent units are obtained by

combining more than one profi le, allowing to meet the diff erent needs.

The lighting parts are protected by a polycarbonate screen, designed to provide the best diff usion of light.

The lamp unit, consisting of direct, indirect and night light, with the necessary bulb sockets, ballast and starter is

assembled on a single base that is suitably painted to better refl ect the light.

Designed to facilitate maintenance, lamps are attached to the

profi le structure without the use of screws, and are connected/

disconnected from the electrical cabling of the bed head unit using

a single connector.

Designed and built by Sostel in accordance with Annex II of

Directive 93/42/EEC for medical devices, the Kabel series bed

head are classifi ed as Class IIb and are customizable with the

following choices:

• number of beds

• total length of the device

• wall or ceiling mount

• color and surface finish

• types of components: electrical, data transmission etc.

• support for accessories such as monitors, IV bars and hooks etc.

• preparation for the type and number of medical gas outlets.

6

CHANNELS

The diff erent types of Kabel series bed head units are obtained by

combining nine diff erent profi les that have “channels” with the following

functions:

• lighting;

• distribution of electricity, alarms reporting and communication lines;

• distribution of medical gases.

LIGHTING CHANNELLighting services are placed in the top section of the bed head unit in a profi le

that shows wide connection radii to produce diff erent optimal angles for

direct and indirect light, covered with a polycarbonate screen, designed to

provide maximum illumination.

The interior of the profi le is designed to house high (A) and low (B) voltage

wiring in separate sections.

Lighting is structured in the following ways:

• Ambient Light: indirect, with compact, linear fl uorescent

lamps with starter or electronic power units of 18, 30, 36, 55

or 58 W (or combinations of them);

• medical light: direct, with two 18 W fl uorescent lamps;

• reading light: 18 W fl uorescent lamp;

• night light: 15 W max incandescent lamp or LED lamp.

B

AA) High-voltage wiring.

B) Low-voltage wiring.

7

DISTRIBUTION CHANNEL FOR ELECTRICITY AND DATA

The electricity distribution services can

be housed directly in the top profi le of the

bed head unit or in a separate dedicated

front profi le.

The front profi le solution is unique in

that the support which holds the various

signal and communication outlets is fi xed

to the profi le without screws, with the

aid of hooks, while maintaining an IP40

insulation and, when opened, is supported

by cords, for easy, safe installation.

Based on the individual need, electricity and signals can be distributed using:

• sockets, Schuko and UNEL, with or without power indication led, protected or not by fuses and circuit

breakers;

• buttons;

• warning lights;

• switches and buttons to control lights;

• sockets for data (RJ45) and telephone (RJ11-RJ12);

• nurse call outlet;

• equipotential grounding.

CHANNEL FOR MEDICAL GASES

The circuit dedicated to the medical gas system is inserted in a separate channel, fully mechanically separated

from the other profi les.

Integrated into the structure, without the need for additional wall mounting, this channel houses medical gas

tubing and sockets that can also be placed in a special separate box.

Up to six tubes can be installed in the channel, for the distribution of

the following medical gases:

• oxygen;

• nitrous oxide;

• vacuum;

• compressed air;

• any pipes for the passage of water can be enclosed in another

channel.

ALL KABEL SERIES BED HEAD UNITS ARE SUPPLIED BY SOSTEL WITHOUT

SOCKETS AND TUBES FOR MEDICAL GASES

8

CHANNELS

ALL EQUIPMENT, EXCEPT MASTS, ARE AVAILABLE IN SUSPENDED VERSIONS

PRODUCT INDEX

WINCH

GOSTER GAS

JIB

p. 11

p. 13

p. 18

p. 19

p. 21

p. 22-24

p. 17

p. 15

p. 16

p. 14

p. 12

p. 11GOSTER LIGHT

GOSTER

MAIN

GENN

SPINN

MAST

p. 20SUSPENDED

NEWS FROM KABEL SERIES

MAIN GAS

JIB GAS

0051

10

GOSTER FOR LABORATORIES

Equipment made of extruded aluminum profi les where

the front plate, which houses the electric sockets, is snap-

mounted, so without screws, maintaining an IP40 protection

grade.

The front plate, when opened, is supported by cords, thus

facilitating installation and maintenance.

The device is primarily designed to hold electrical parts and

components for communication and signaling, responding

to the needs of laboratories and resuscitation/dialysis

departments. To better meet the needs, it is made in two

sizes: 167 x 85 mm for the Goster version and 119 x 85 mm

for the Goster Light version.

MOD. GOSTER LIGHT

MOD. GOSTER

GOSTER

167

GOSTER LIGHT

119

85

85

11

12

JIB FOR LONG-TERM CARE WARDS

Basic equipment, of compact dimensions, made from an

extruded aluminum structural profi le in which various

routes are designed for the well-separated passage of

electrical, signaling and alarm conductors.

The oblique lower side houses the switches and electrical

outlets, so they are closer to the patient.

The lighting parts are protected by a polycarbonate screen,

designed to provide better diff usion of light in the room.

The direct, indirect and night lamps, with their necessary

components such as lampholders, ballasts and starters are

assembled on a single base, appropriately painted to refl ect

light. Designed to facilitate its maintenance, the lamp unit is

fastened to the structural profi le without the use of screws,

and can be connected/disconnected from the equipment’s

power supply by means of a single connector.

222

JIB

JIB LARGE

137

169

199

199

85

85

13

MAIN FOR IN-PATIENT WARDS

The front plate, which houses the electric sockets, is

snap mounted, so without screws, maintaining an IP40

protection grade and, when opened, is supported by

cords, thus facilitating safe installation and maintenance.

A compact device, designed for departments that require

important and easily reachable equipment.

Made with two profi les, the fi rst one structural in which

various well-separated paths are provided for the passage

of electrical, data and alarm conductors, and the second

one prepared for housing sockets, equipotential ground

nodes and other customizations.

267

199

85

GOSTER GAS FOR PREPARATION AND RESUSCITATION DEPARTMENTS

This device consists of two extruded aluminum profi les,

separated and closed by screwless, snap-fastened front

supports, which houses the electrical sockets and gas

outlets.

Goster Gas electromedical equipment meets the

requirements of laboratories, resuscitation and dialysis

departments and all those situations where order and safety

The front supports, when opened, are supported by cords, thus

allowing easy and safe installation and maintenance. Each of the

two profi les are prepared for a specifi c function: the fi rst one for

the passage of electrical and signal cables, the second one for the

passage of tubes and for the distribution of medical gases.

are required, and where “fl ying” cables and gas tubes are

not allowed. To better meet the needs, it is produced in two

diff erent sizes: a 249x85 mm Goster version and a 297x85

mm Large Goster Gas version.

Note: The electrical devices are supplied tested and ready for installation;

medical gas tubes and outlets are not included

14

297

149

249

100

85

85

GOSTER GAS LARGE

GOSTER GAS

JIB GAS FOR IN-PATIENT WARDS AND LONG-TERM CARE WARDS

A device consisting of two extruded aluminum profi les:

in the fi rst, structural, a number of well separated paths

are provided for the passage of electrical, signal and alarm

conductors, while medical gas tubes are housed in the

second, mechanically separated from the fi rst.

The gas outlets can be located in a third profi le, dedicated

to them and called the “gas outlets box”.

The switches and electrical outlets are placed on the

bottom oblique side of the structural profi le. The lighting

parts are protected by a polycarbonate screen while

the direct, indirect and night lamps, with their necessary

components, such as lampholders, ballasts and starters,

are assembled on a single base, appropriately painted to

refl ect light.

15



186

268

199

85

WINCH FOR IN-PATIENT WARDS AND LONG-TERM CARE WARDS

WINCH ELECTRIC VERSION

WINCH LARGE VERSION

An electromedical device that combines the illuminating

structural profi le and a special “gas outlet box”, designed to

accommodate gas accessories without the need for extensions

or reductions.

Switches and electrical outlets are located on the oblique

bottom side of the device or, in the Winch Electric version, they

are inserted in a “box”, identical to the gas box, and placed

on the opposite side, thus giving the whole a balanced and

attractive design.

Both the polycarbonate screen, placed to protect the indirect

light, and any other parts are rounded to facilitate cleaning.

16



186

219

199

156

MAIN GAS FOR IN-PATIENT WARDS

One of the most complete devices of the Kabel series,

it consists of three extruded aluminum profi les: lighting,

electrical distribution and medical gas distribution.

The front plates, where the electrical sockets and the gas

outlets are placed, are snap-mounted, so without screws,

maintaining an IP40 protection grade.

17



316

398

199

85

GENN FOR PRE-OPERATIVE, RESUSCITATION AND DIALYSIS DEPARTMENTS

One of the most compact electromedical devices of the Kabel

series because it combines light, electricity distribution and

gas distribution in one profi le, while maintaining the electrical

components mechanically well separated from the medical

gas components. The front plate, where the electrical sockets

and the gas outlets are placed, is snap-mounted, so without

screws, maintaining an IP40 protection grade and, when

opened, it is supported by cords, facilitating easy installation

and safe maintenance.

Designed to facilitate maintenance, the lamp unit is fastened to the profi le

structure without the use of screws and is connected/disconnected from the

electrical supply of the unit using a single connector.

18

Note: The electrical devices are supplied tested and ready for installation; medical gas

tubes and outlets are not included

199

365

85

SPINN FOR RESUSCITATION AND PRE-OPERATIVE AREAS AND DIALYSIS UNITS

This is the most complete electromedical device of the Kabel

series, of which all the types of bed head units are a variant.

It consists of three extruded aluminum profi les: light, electricity

distribution and medical gas tubes and distribution.

It is especially suitable for those situations in which many

components are required in a single element: sockets,

equipotential grounds, data outlets, nurse call outlets etc., and

it is mainly intended for dialysis units and resuscitation and pre-

operative areas. The front support, in which the electrical and gas

outlets are placed, is snap-mounted, without the need of screws;

it gives an IP40 protection grade and, when it is opened, it is

supported by cords, facilitating easy installation and maintenance.

To better meet the needs, it is produced with two diff erent

dimensions: Spinn 349x199 mm and Spin Large 398x199 mm.SPINN LARGE

19

Note: The electrical devices are supplied tested and ready for

installation; medical gas tubes and outlets are not included

349

100 14

9

398

199

199

85 85SPINN LARGESPINN

SUSPENDED FOR RESUSCITATION AND PRE-OPERATIVE AREAS AND DIALYSIS UNITS

20

All models of bed head units of the Kabel series, with the exclusion of the Mast model, are

available with the same functionalities, in a suspended version or two-faced suspended

version.

The suspension beams are made of specific 4mm think aluminum profiles, anchored to the

ceiling with steel brackets, and are purpose-made to guarantee:

• A particular robustness to the whole structure

• Plant safety, as the power supply/data

lines and the gas pipes are housed in

separate locations

• Ease of installation and maintenance

• Complete absence of sharp edges,

since all the profiles are rounded

• A nice design



21

MAST FOR LONG-TERM CARE WARDS AND NURSING HOMES

A bed head unit made from an extruded

aluminum profi le in which a number of well-

separated paths are provided for the passage

of electrical, signal and alarms conductors and

which houses the medical gas components,

separated from the electrical ones.

A typical application of MAST is to provide

electrical services and medical gases to two

beds with a single device.

The electromedical device is fi xed vertically on

the wall.

85

231

22

VAN FOR IN-PATIENTS WARDS AND LONG-TERM CARE WARDS

VAN GAS

Extremely compact electro medical device which, in small spaces, - 290x85 mm - includes the direct and indirect lighting

channels for the accommodation of the electrical components.

It is made of three aluminum profi les, 2 mm thick. In the middle one, diff erent well separated paths are set for the passage

of electrical, signaling and alarm conductors. Also, on the front support, sockets, equipotential grounding, control switches,

nurse call outlets and other customizations are housed. The front support is screwless, snap mounted and, when opened, it

is held by cords, which makes the installation and maintenance easy and safe. In the remaining two profi les fl uorescent T5

bulbs or LED modules, with their components, are located.

Bedhead unit which incorporates

the core services of lighting, electrical

distribution and medical gases distribution.

The front frame, in which electrical fruits and gas outlets are placed, is screwless and snap mounted,

maintaining an IP 40 protection degree. Electrical and medical gas outlets are mechanically

separated and placed In the central part of this compact unit. The Van Gas bedhead can be fi xed

to the wall with the aid of simple brackets which allow for an easy and safe installation or, as for the

whole Kabel series range, can be hung to the ceiling with side beams and the appropriate fl anges.



85

290

23222

TWIN FOR RESUSCITATION AND PRE-OPERATIVE AREAS AND DIALYSIS UNITS

Bedhead device consisting of superimposed channels,

designed for those situations in which a unit with many electrical

and medical gas components is required.

The Twin bedhead completes the range of the compact units,

designed to be used in situations which require a reduced

aesthetic and dimensional impact. Manufactured according to

the electro medical equipment regulations, the Twin bedhead

uses two external profi les for room and direct lighting, in two

possible solutions: a LED one, energy saving, or one with T5

tubes.

The particular rounded shape, of the two outer channels,

prevents dust from settling easily, and it favors a rapid and

thorough cleaning at the same time.

The controls and the electric and gas outlets are placed on

faceplates which are screwless and snap mounted. When

opened, the front panels are supported by cords, which make

the installation and maintenance easy and safe.



85

420

24242424

BULBO FOR IN-WARDS PATIENTS

COMBO

Illuminating unit of limited size consisting of two aluminum profi les designed to

house only the lighting components such as reading, direct and indirect lights

with the use of fl uorescent T5 lamps or LED modules.

Its simple aesthetic allows it to well integrate into any hospital environment, also

thanks to the inclination of the two light diff users, that uniformly propagate the

light both to the room and to the patient.

Designed to be installed horizontally and wall mounted, BULB is supported by

a pair of brackets which make the installation easy and the maintenance safe.

Bulb is within the range of Kabel bedhead series and is produced in compliance

with the relative norm.

A product that consists of multiple extruded-aluminum profi les that incorporate

all the functions of a bed head unit and is assembled on a central wooden

structure with shelves and compartments.

In practice, it is a multifunctional piece of design furniture with the aim to

integrating well with the environment and “humanizing” the patient’s room.



85

192

The main feature of our products is their customization, as each electromedical system is made according to specifi c customer

requirements. This versatility allows us to include in the variants, defi ned before production, anodizing and painting with any

color.

Note: These colors are indicative and may not accurately refl ect their appearance on metal.

WOOD EFFECT EXAMPLES

OAK 3402 DOUGLAS 1010 PINE 3401 CHERRY 3630 CHERRY 3630R CHESTNUT 3650

RAL EXAMPLES

RAL 9010 WHITE

OAK 3610

26

TYPES OF COLORING

OPTIONS

RAL 5005 RAL 6019 RAL 6032 RAL 3020 RAL2004 RAL 1023

27

Esthetic properties in the choice of a bed head unit are important for our customers; among the various custo-

mizations they can choose the shape of the direct light from four possible types.

luminous effi ciency 100%




In the range of the aluminum profi les that make up the bed head units of the Kabel series, Sostel has four

diff erent channels for the passage of tubes and housing medical gases outlets. The choice of gas channels,

each in a diff erent size, depends on installation needs and the number of medical gas sockets and tubes.

Note: The electrical devices are supplied tested and ready for installation; medical gas tubes and outlets are not included

TYPES OF GAS CHANNELS

OPTIONS

STANDARD

QUADRA

RONDÒ

ELLISSE

TYPE OF DIRECT LIGHT

50492087

3294 2086

KABEL SERIES ACCESSORIES

28282828

PANTOGRAPH LAMPLamps used in the medical fi eld, designed

to concentrate the light fl ux in an area of

interest. They can be fi xed to the tool bar and

be powered from an outlet located on the bedhead.

ROD FOR INFUSION PUMPRound tubular steel profi le bar that can be fastened to

the tool bar; on it the infusion pump is applied.

WALL BRACKETSMade of steel material, 1.5 mm thick, they are fi xed to

the wall with wall bolts. Their shape has been studied to

“fi x” the bedheads, with the lighting channel, safely and

rapidly. They come in pairs for bedhead with a maximum

length of 2m; beyond that length additional brackets are

needed.

PUSH PEARSElement of communication and control available to the

patient, with a nurse call function and command / control

of auxiliaries made available for the patient comfort, such

as ambient light, reading light, TV control, intercom, etc.

Any push pear type or model can be mounted on the

Kabel series bedheads.

TOOL BARRectangular stainless steel or aluminum bar, of size

30x10 mm and thickness 1.5 mm. It is mounted on the

bedhead, with a special profi le, or fi xed to the wall. The

fastening screws, on both the headboard or wall, are not

visible, favoring the locking or sliding of the accessories.

STAND HOOKTreated steel component, placed in the lower part of the

bedhead, fi xed or sliding.

IV POLEMade of tubular stainless steel, it clips to the tool bar via

an appropriate “block”. It can slide on the tool bar and

rotated 180 °; on it usually 4 IV hooks are applied.

SUCTION PAD PROFILES OPENERThe bedheads of the Kabel series have been designed

with removable snap mounted parts.. These parts can be

removed by means of a suction pad of silicone material,

without the help of tools that could scratch the surface.

CEILING FIXING BRACKETSMade of steel material, 3 to 5mm thick, they are compo-

sed of a series of elements such as fl ange and counter

fl ange, threaded rods, tower united with the fl ange,

bolts... suitable to support all the “horizontal” bedhead

of the Kabel series. The components of this fastening

system have been designed to facilitate the installation

and put the bedhead in parallel with the ground.

CHESTWith one or two drawers it is made of stainless steel

or antibacterial ABS; the top shelf is used as monitor

holder. The drawer can be fi xed to the tool bar directly

or through a “U”shaped structure, or to the wall. Also

available with one drawer, covered with antibacterial

ABS and top shelf 440X400X150.

VERTICAL BAR SYSTEMVertical bar system (two rods h = 1000mm) in AISI 304

stainless steel, for the mounting of shelves and chests

(adjustable height, for wall bedheads).

NB Shelf and chest not included

A. 440X400 AISI 304 stainless steel shelf with 3 edges

B. One drawer chest with a top shelf without edges

MONITOR HOLDERAccessory manufactured with a stainless steel frame

and with stainless steel or antibacterial ABS 450x450

mm shelves. The monitor holder is fi xed to the tool bar

by means of a block which also favors the sliding.

B

A

30

The bed head unit comes complete (lamps, tubes and gas outlets excluded) and tested, ready for wall mounting.

The recommended fastening height is 1.7 m from the fl oor and the metal steel brackets supplied with the unit must be used.

Each bracket must be fi xed to the wall with anchors that are suitable for that type of wall and have a minimum strength of

2.3 kN of axial traction.

The distances between the brackets depends on the type of unit and are shown directly on the drawings together with the

brackets.

Be aware that bed head units are normally supplied with two brackets for each bed, with a maximum distance between them

of 1,600 mm. In case a greater distance is needed, two additional brackets will be supplied.

For bed head units of the type MAIN, MAIN GAS and GEN, two anchors are needed per side, while the SPINN model needs

four anchors per side.

Diff erent brackets must be used for the suspended version. Bed head units of the type Goster, Goster Light, Goster Gas,

Goster Gas Large and Mast are fi tted directly to the wall without the use of brackets.

JUNCTIONS FOR “CONTINUOUS” BED HEAD UNITS FOR MULTIPLE BEDS

WALL MOUNTING

1 332

4 5 6

FASTENING SEQUENCE

7 98

REFERENCES - SOME OF OUR ACHIEVEMENTS

33

TECHNICAL SPECIFICATIONS FOR KABEL SERIES BED HEAD MEDICAL EQUIPMENT

CLASSIFICATION ACCORDING TO DIRECTIVE 93/42/EEC - ANNEX II

Classifi cation according to the type of protection against

electrical hazards

Class I device

The protection against electric shock is provided by grounding metal parts

Classifi cation according to the type of protection against direct

and indirect contact

Type B device

Classifi cation according to the degree of protection against

penetration of external agents

IP40

Classifi cation according to the operating conditions Apparatus for continuous operation

Noise level Less than 35dB

Testing for each unit For each individual unit, the following tests are performed :

- impedance to ground, conforming to point 18f of EN 60601-1:1998

- current leakage to ground conforming to points 19.3e and 19.4 of EN 60601 - 1:1998

Electromagnetic interference The bed head units do not cause electromagnetic interference to other devices

Voltage 220 / 230VAC

Frequency 50 Hz

Auxiliary voltage (typical) 24VDC-VAC

Power consumption (220-230V)

- with regard to lamps

- with regard to outlets

max 150W (0.7 A)

max 2.000W per each outlet

3.000W Total

Electromagnetic Compatibility Directive The device complies with Directive: 89/336/EEC and subsequent amendments and additions

Low Voltage Directive The device complies with Directive 93/68/EEC and subsequent amendments and additions

Medical Equipment Directive The device complies with Directive: 93/42/EEC and subsequent amendments and additions

Reference Standards The device complies with Standards:

UNI EN ISO 11197: 2009

EN 60601-1-2/A1: 2006-5

EN 61000-3-2: 2000

EN 61000-3-3: 1995 A1: 2000

EN 55015:2000 A1: 2001 A2: 2002

EN 50366:2003

1999/519/EC:1999

D.Lgs.151/05

Section Point Classifi cation

I DEFINITIONS 1.1 Long-term The devices are intended to be typically

used for a continuous period exceeding

30 days

III CLASSIFICATION 1.2 Rule 2

3.1 Rule 9

3.2 Rule 11

Devices are classifi ed as Class IIb

36

All

com

pa

ny

na

me

s a

nd

/ o

r p

rod

uct

s m

en

tio

ne

d in

th

is c

ata

log

are

tra

de

ma

rks

or

reg

iste

red

tra

de

ma

rks

of

the

ir r

esp

ect

ive

ow

ne

rs a

nd

eve

n t

he

pro

du

cts

fea

ture

d a

re a

rtic

les

ma

de

by

the

ir r

esp

ect

ive

tra

de

ma

rk h

old

ers

Due to the evolution of standards and materials, technical features within the text and illustrations in this document may be considered binding only after confi rmation by Sostel SpA

Mo

d D

PL

00

1 R

ev

00

7/E

NG

we

b/0

9-1

2

Sostel S.r.l.

Via Tonale, 15 - 24061 Albano S. Alessandro (BG) - ITALY - Tel. +39 035 580580 - Fax +39 035 580863 - [email protected]

www.sostel.eu

Registro A.E.E. IT08020000000373

Azienda Certifi cata ISO 9001:2008 / ISO 13485:2012

9160.SOS1 IT-43171 9124.SOS2

ph

oto

: A

ng

elo

Pa

rsa

ni

systems for a communicating world

®

sostel - bed heads catalogue 2013

Documents

electromedical bed head

complex units

term production

daily production

production cycle

bed head unit layout

suspended ceiling units

technical drawings