sony_kdl-46-55-hx920-hx923-hx925_az2chassis service manual
DESCRIPTION
sony_kdl-46-55-hx920-hx923-hx925_az2chassis service manualTRANSCRIPT
-
SERVICE MANUAL
Version Date Subject1.0 4/2011 Original manual issue.
LCD Digital Color TV
9-888-423-01
HISTORY INFORMATION FOR THE FOLLOWING MANUAL:
ORIGINAL MANUAL ISSUE DATE: 4/2011 AZ2F CHASSISSegment: 2b-1
KDL-46/55HX920,923,925 (AEP/UK/RUSSIA)S/N range 3,000,001-3,999,999 (FX)
-
SERVICE MANUAL
LCD Digital Color TV
AZ2F CHASSISSegment: 2b-1
9-888-423-01
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 3
MODEL LIST
MODEL COLOR COMMANDER DEST.MODEL COLOR COMMANDER DEST.KDL-46HX920 Black RM-ED041 AEP/RUSSIAKDL-46HX923 Black RM-ED041 AEP/UKKDL-46HX925 Black RM-ED041 AEP
KDL-55HX920 Black RM-ED041 AEP/RUSSIAKDL-55HX923 Black RM-ED041 AEP/UKKDL-55HX925 Black RM-ED041 AEP
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 4
WARNINGS AND CAUTIONS - ENGLISH
CAUTIONThese servicing instructions are for use by qualified service personnel only.To reduce the risk of electric shock, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.
WARNING!!An isolation transformer should be used during any service to avoid possible shock hazard, because of live chassis.The chassis of this receiver is directly connected to the ac power line.
CARRYING THE TVBe sure to follow these guidelines to protect your property and avoid causing serious injury. Carry the TV with an adequate number of people; larger size TVs require two or more people. Correct hand placement while carrying the TV is very important for safety and to avoid damages.
SAFETY-RELATED COMPONENT WARNING!!Components identified by shading and ! mark on the schematic diagrams, exploded views, and in the parts list are critical for safe operation. Replace these components with Sony parts whose part numbers appear as shown in this manual or in supplements published by Sony. Circuit adjustments that are critical for safe operation are identified in this manual. Follow these procedures whenever critical components are replaced or improper operation is suspected.
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 5
WARNINGS AND CAUTIONS - FRENCH
ATTENTION!!Ces instructions de service sont lusage du personnel de service qualifi seulement. Pour prvenir le risque de choc lectrique, ne pas faire lentretien autre que celui contenu dans le Mode demploi moins que vous soyez qualifi faire ainsi.
WARNING!!Afi n deviter tout risque delectrocution provenant dun chssis sous tension, un transformateur disolement doit etre utilis lors de tout dpannage. Le chssis de ce rcepteur est directement raccord lalimentation du secteur.
POUR TRANSPORTER LE TLVISEURTenez compte de ce qui suit pendant linstallation du tlviseur : Dbranchez tous les cbles avant de transporter le tlviseur. Transportez le tlviseur avec le nombre de personnes appropri ; un tlviseur de grande taille doit tre transport par au moins deux personnes. Lors du transport du tlviseur, lemplacement des mains est trs important pour votre scurit, ainsi que pour viter de causer des dommages.
ALERTE!!Afi n deviter tout risque delectrocution provenant dun chassis sous tension, un transformateur disolement doit etre utilise lors de tout depannage. Le chassis de ce recepteur est directement raccorde a lalimentation du secteur.
ATTENTION AUX COMPOSANTS RELATIFS A LA SECURITE!!Les composants identifi es par une trame et par une marque ! sur les schemas de principe, les vues explosees et les listes de pieces sont dune importance critique pour la securite du fonctionnement. Ne les remplacer que par des composants Sony dont le numero de piece est indique dans le present manuel ou dans des supplements publies par Sony. Les reglages de circuit dont limportance est critique pour la securite du fonctionnement sont identifi es dans le present manuel. Suivre ces procedures lors de chaque remplacement de composants critiques, ou lorsquun mauvais fonctionnement suspecte.
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 6
WARNINGS AND CAUTIONS
USE CAUTION WHEN HANDLING THE LCD PANELWhen repairing the LCD panel, be sure you are grounded by using a wrist band.When repairing the LCD panel on the wall, the LCD panel must be secured using the 4 mounting holes on the rear cover.
1) Do not press on the panel or frame edge to avoid the risk of electric shock.2) Do not scratch or press on the panel with any sharp objects.3) Do not leave the module in high temperatures or in areas of high humidity for an extended period of time.4) Do not expose the LCD panel to direct sunlight.5) Avoid contact with water. It may cause a short circuit within the module.6) Disconnect the AC power when replacing the backlight (CCFL) or inverter circuit. (High voltage occurs at the inverter circuit at 650Vrms.)7) Always clean the LCD panel with a soft cloth material.8) Use care when handling the wires or connectors of the inverter circuit. Damaging the wires may cause a short.9) Protect the panel from ESD to avoid damaging the electronic circuit (C-MOS).10) It is recommended not to exceed 1 hour of Power-On nor Burn-in period with LCD panel face down condition, in repair activity.
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 7
- Please hold the long side more than 200mm from the short side. (Fig.1)
- When you ground Tengo panels beneath, ground it on the level slowly. (Fig.2)
More than 200mm from the short side
HANDLING THE TENGO PANELWhen handling the TENGO panel, please obey the following instructions.
WARNINGS AND CAUTIONS
Fig.1
Fig.2
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 8
By following handling, resin separation/cracking of glass may be occurred, restrict the following items.
1. Temporarily putting on lower cushion with bottom of glass. (Fig.1)
2. Ground with the bottom of glass. (Fig.2)
3. Grip as palm touches glass side. (Fig.3)
4. Hold the short side. (Fig.4)
5.Hold glass only when glass side up. (Fig.5)
Easy to bent
WARNINGS AND CAUTIONS
Fig.1 Fig.2 Fig.3
Fig.5Fig.4
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 9
When replacing the Tengo panel at service, please note the followings.
- Unpack the carton box, pull out the panel with reinforcing plates. (Fig.3)
-Together with reinforcing plates, place the panel with face down slowly. (Fig.4)
* Please use the reinforcing plates as operating table.
NOTES ON REPLACING THE TENGO PANEL
WARNINGS AND CAUTIONS
Fig.3 Fig.4
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 10
When replacing the Tengo panel at service, please note the followings.
- Unpack the package of Tengo panel. (Fig.5)
- Cut protection bag at the center of the back of panel. (Fig.6)
* Please cut the protection bag carefully, the bag will be used for re-packing.
WARNINGS AND CAUTIONS
Fig.6Fig.5
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 11
When replacing the Tengo panel at service, please note the followings.
- Assemble TV set with the new panel. (Fig.7)
- After assembly, attach Stand Unit and stand the TV up. (Fig.8)
WARNINGS AND CAUTIONS
Fig.7 Fig.8
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 12
When replacing the Tengo panel at service, please note the followings.
- Set the plastic bag on correct position of package and place the replaced panel on it. (Fig.9)
* Handle the panel carefully as the instruction below.
- Align the bottom side of panel with cushions on the package. (Fig.10)
* Please note that it may damage to the glass surface if you pack panel in the wrong orientation.
* Please handle with care to prevent hitting the glass of panel to package materials.
More than 200mm from the short side
WARNINGS AND CAUTIONS
Fig.10Fig.9
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 13
When replacing the Tengo panel at service, please note the followings.
- Tape the plastic bag on the back of panel to protect panel surface. (Fig.11)
* Please make sure the orientation of the panel again. (T-CON board side is lower.)
- Repack the panel in the original carton box.
Fig.11
Fig.12
WARNINGS AND CAUTIONS
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 14
2
1
1Push!!
When you insert / pull out FFC, please grasp a reinforcement board and main body of FFC.
< Insertion >
Please hold reinforcement board and plunge it to the depths.
Please pull out FFC while pushing the button of both ends at the same time.
Reinforceplate
B board
FFC can reverse insertion to connector of B board.If reverse insertion FFC, all pins short-circuit, and board is broken.
Upper side is GND shieldUpper side is terminal
HANDLING THE FFC
WARNINGS AND CAUTIONS
Reinforceplate
B board
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 15
SAFETY CHECK-OUT
After correcting the original service problem, perform the following safety checks before releasing the set to the customer:
1. Check the area of your repair for unsoldered or poorly soldered connections. Check the entire board surface for solder splashes and bridges.
2. Check the interboard wiring to ensure that no wires are pinched or touching high-wattage resistors.
3. Check that all control knobs, shields, covers, ground straps, and mounting hardware have been replaced. Be absolutely certain that you have replaced all the insulators.
4. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement.
5. Look for parts which, though functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement.
6. Check the line cords for cracks and abrasion. Recommend the replacement of any such line cord to the customer.
7. Check the antenna terminals, metal trim, metallized knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below.
8. For safety reasons, repairing the Power board and/or Inverter board is prohibited.
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 16
SAFETY CHECK-OUT
Leakage TestThe AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microamperes).Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturersinstructions to use these instructions.
2. A battery-operated AC milliampmeter. The Data Precision 245 digital multimeter is suitable for this job.3. Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The
limit indication is 0.75 V, so analog meters must have an accurate low voltage scale.The Simpsons 250 and Sanwa SH-63TRD are examples of passive VOMs that are suitable. Nearly allbattery-operated digital multimeters that have a 2 VAC range are suitable (see Figure A).
How to Find a Good Earth GroundA cold-water pipe is a guaranteed earth ground; the cover-plate retaining screw on most AC outlet boxes is also at earth ground.If the retaining screw is to be used as your earth ground, verify that it is at ground by measuring the resistance between it and a cold-water pipe with an ohmmeter. The reading should be zero ohms.If a cold-water pipe is not accessible, connect a 60- to 100-watt trouble- light (not a neon lamp) between the hot side of the receptacle and the retaining screw. Try both slots, if necessary, to locate the hot side on the line; the lamp should light at normal brilliance if the screw is at ground potential (see Figure B).
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 17
SELF DIAGNOSIS FUNCTION
DIAGNOSTIC TEST INDICATORSWhen an error occurs, the STANDBY LED will flash a set number of times to indicate the possible cause of the problem.If there is more than one error, the LED will identify the first of the problem areas.Result for all of the following diagnostic items are displayed on screen.If the screen displays a 0, no error has occurred .
The units in this manual contain a self-diagnostic function. If an error occurs, the STANDBY LED will automatically begin to flash.The number of times the LED flashes translates to a probable source of the problem.A definition of the STANDBY LED flash indicators is listed in the instruction manual for the users knowledge and reference.If an error symptom cannot be reproduced, the remote commander can be used to review the failure occurrence data stored in memory to reveal past problems and how often these problems occur.
0.50.5
3
DISPLAY OF STANDBY LED FLASH COUNT
SELF-DIAGNOSTIC SCREEN DISPLAYFor errors with symptoms such as power sometimes shuts off or screen sometimes goes out that cannot be confirmed, it is possible to bring up past occurrences of failure for confirmation on the screen:
[To Bring Up Screen Test]In standby mode, press buttons on the remote commander sequentially in rapid succession as shown below:
5* : Note that this differs from entering the service mode (volume +)
*
DISPLAY TV POWERChannel Volume
STBY LEDFlash time
Service menu Itemname
(Screen Display)Diagnostic Item Description
2 MAIN_POWE Main Power Over Voltage ProtectionDC_ALERT DC_ALERTAUD_PROT Audio Abnormal Detection
VLED LED Voltage protectionBALANCER LED driver failureTCON_ERR T-CON ErrorHFR_ERR HFR ErrorP_ID_ERR Panel ID NVM Error
6 BACKLITE Back Light Error (Panel Inverter)TEMP_ERR Thermal ErrorFAN_ERR Fan Error
8 - Software Error9 - Not used10 EMITTER Emitter Error11 - Not used12 - Not used
3
5
7
4
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 18
SELF DIAGNOSIS FUNCTION
[SELF DIAGNOSTIC SAMPLE SCREEN DISPLAY]
Since the diagnostic results displayed on the screen are not automatically cleared, always check the self-diagnostic screen.After you have completed the repairs, clear the result display to 0.
Clearing the Self Check Diagnostic List1. Error history and Error count : Press the Channel 8 => Channel 0 .2. Panel operation time : Press the Channel 7 => Channel 0 .
Exiting the Self-diagnostic screenTo exit the Self Diagnostic screen, turn off the power to the TV by pressing the POWER button on the remote or the POWER button on the TV.
SELFCHECKNEXTPAGE>
000RGB_SEN 00002MAIN_POWE 00003DC_ALERT 00003AUD_PROT 00003DTT_WDT 00004VLED 00004BALANCER 00005HFR_ERR 00005TCON_ERR 00005P_ID_ERR 00006BACKLITE 00007TEMP_ERR 00007FAN_ERR 00010EMITTER 00011IA 00
123456789123456
Error count (00-99)
Error history (Last failure time beforehand)
Error history (Failure time before last)
Error history (The last failure time)
Item name
STBY LED flash time
Total operation time by hour (MAX:65535)
Boot count (MAX:65535)
Panel operation time by hour (MAX:65535)
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 19
SEC 1. DISASSEMBLY
There are clutch in the yellow frame[ ]. Therefore please be careful in the case of the disassembly or assembly of parts.
Note: Metal type Rear Cover is used in these models. When handle the Rear Cover, please pay special attention to the sharp edges due to no curing finish. When working, wearing gloves is recommended. Location of the sharp edges, please refer to APPENDIX-2.
Note: When removal rear cover, damaged with rear cover and power supply cord.Removal the rear cover and power supply cord, please refer to APPENDIX-1.
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 20
1-1. KDL-46HX920/923/925
1-1-1. STAND BLOCK, HEAD STAND, NECK AND BASE STAND
DISASSEMBLY
HEAD STAND
NECK
BASE STAND
1 Screw (USER SCREW ST) Inside bag, screw assy3 Screws (SCREW, +PSW M5X16) Inside bag, screw assy
3 Screws (USER SCREW ST) Inside bag, screw assy
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 21
DISASSEMBLY
1-1-2. REAR COVER, AC COVER, ANT COVER AND ANT SHEET
8 Screws (SCREW, +PSW M3X5) P/N: FX0036001
4 Screws (SCREW, +BVTP 4X12 TYPE2 IT-3) P/N: FX0005801
6 Screws (SCREW, ORNAMENTAL M6X12) P/N: FX0006302
3 Screws (SCREW +BVTP 3X8 TYPE2 IT-3) P/N: FX0012779
2 Screws (JOINT, STAND) P/N: FX0002101
1 Screw (SCREW, +PSW M3X6 W12) P/N: FX0001901
1-1. KDL-46HX920/923/925
AC COVERREAR COVER
ANT COVER
ANT SHEET
ANT COVER
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 22
DISASSEMBLY
1-1-3. SWITCH UNIT AND POWER SWITCH
SWITCH UNIT
1-1. KDL-46HX920/923/925
POWER SWITCH
SWITCH UNIT
CONNECTOR ASSY
SWITCH UNIT
CONNECTOR ASSY
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 23
DISASSEMBLY
1-1-4. HARNESSCONNECTOR ASSY 28P
CONNECTOR ASSY 14P
FLEXIBLE FLAT CABLE
HARNESS ASSY
1-1. KDL-46HX920/923/925
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 24
1-1-5. POWER SUPPLY CORD AND G5B BOARD
DISASSEMBLY
2
3
3 Screws (SCREW (+PSW) (M3X6)) P/N: FX0001341
G5B BOARD
INSULATION SHEET
1-1. KDL-46HX920/923/925
G5B BOARD
4
G5B BOARD
5
G5B BOARD
POWER SUPPLY CORD
1
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 25
1-1-6. WIRELESS LAN CARD
DISASSEMBLY
1 2
1 Screw (SCREW (+PSW) (M3X6)) P/N: FX0001341
WIRELESS LAN CARD
1-1. KDL-46HX920/923/925
WIRELESS LAN CARD
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 26
1-1-7. ANTENNA
DISASSEMBLY
1 2
2
ANTENNA
1
1 Screw (SCREW (+PSW) (M3X6)) P/N: FX0001341
ANTENNA
1-1. KDL-46HX920/923/925
ANTENNA
ANTENNA
1 Screw (SCREW (+PSW) (M3X6)) P/N: FX0001341
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 27
1-1-8. SPEAKER BOX ASSY
DISASSEMBLY
1-1. KDL-46HX920/923/925
SPEAKER BOX ASSY
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 28
1-1-9. SPEAKER BOX ASSY (WOOFER)
DISASSEMBLY
1-1. KDL-46HX920/923/925
SPEAKER BOX ASSY(WOOFER)
SPEAKER BOX ASSY(WOOFER)
3 Screws (SCREW, +PSW M3X6 W12) P/N: FX0001901
1 2
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 29
1-1-10. BOTTOM BRACKET
DISASSEMBLY
1-1. KDL-46HX920/923/925
BOTTOM BRACKET
1 2
BOTTOM BRACKET
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 30
1-1-11. SIDE BRACKET AND BATL BOARD
DISASSEMBLY
1 2
3 6 Screws (SCREW (+PSW) (M3X6)) P/N: FX0001341
BATL BOARD
BATL BOARDBATL BOARD
SIDE BRACKET
1-1. KDL-46HX920/923/925
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 31
1-1-12. SHEET
DISASSEMBLY
SHEET (BAT-L METAL BOTTOM)
1-1. KDL-46HX920/923/925
1
2
SHEET (BAT-L METAL SIDE)
SHEET (BAT-L METAL SIDE)
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 32
1-1-13. CAMERA MODULE AND SEALING CAP(CAMERA)
DISASSEMBLY
1 2 3
CAMERA MODULE
1-1. KDL-46HX920/923/925
CAMERA MODULE
CAMERA MODULE5 6
SEALING CAP
SEALING CAP
4
1 Screw (SCREW (+PSW) (M3X6)) P/N: FX0001341
CAMERA MODULE
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 33
1-1-14. HEM2 BOARD
DISASSEMBLY
1 2
3
HEM2 BOARD
1-1. KDL-46HX920/923/925
HEM2 BOARD
HEM2 BOARD
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 34
1-1-15. BOTTOM BRACKET AND SP BRACKET
DISASSEMBLY
1-1. KDL-46HX920/923/925
1 1 1
2 2
2
SP BRACKET
SP BRACKET
BOTTOM BRACKET
SP BRACKET
BOTTOM BRACKETSP BRACKET
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 35
1-1-16. FRAME AND JOINT CORNER
DISASSEMBLY
AL FRAME
1-1. KDL-46HX920/923/925
1 2
17 Screws (SCREW, +PSW M3X6 W12) P/N: FX0001901
3
8 Screws (SCREW (+PSW) (M3X6)) P/N: FX0001341HB FRAME
VR FRAMEVL FRAME
HT FRAME HT FRAME
HB FRAME
JOINT CORNERJOINT CORNER
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 36
1-1-17. HLT2 BOARD, PWB (H) TAPE AND PANEL MODULE
DISASSEMBLY
HLT2 BOARD
1-1. KDL-46HX920/923/925
1 2
HLT2 BOARD
PWB (H) TAPE
P-MOD(PANEL MODULE)
INSULATIONSHEET (SW)
ALUMINUM SHEET
HIMERON TAPE (15X60)
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 37
1-2. KDL-55HX920/923/925
1-2-1. STAND BLOCK, HEAD STAND, NECK AND BASE STAND
DISASSEMBLY
HEAD STAND
NECK
BASE STAND
1 Screw (USER SCREW ST) Inside bag, screw assy3 Screws (SCREW, +PSW M5X16) Inside bag, screw assy
3 Screws (USER SCREW ST) Inside bag, screw assy
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 38
DISASSEMBLY
1-2-2. REAR COVER, AC COVER, ANT COVER AND ANT SHEET
11 Screws (SCREW, +PSW M3X5) P/N: FX0036001
4 Screws (SCREW, +BVTP 4X12 TYPE2 IT-3) P/N: FX0005801
6 Screws (SCREW, ORNAMENTAL M6X12) P/N: FX0006302
3 Screws (SCREW +BVTP 3X8 TYPE2 IT-3) P/N: FX0012779
2 Screws (JOINT, STAND) P/N: FX0002101
1 Screw (SCREW, +PSW M3X6 W12) P/N: FX0001901
1-2. KDL-55HX920/923/925
AC COVER
REAR COVER
ANT SHEET
ANT COVER
ANT COVER
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 39
DISASSEMBLY
1-2-3. SWITCH UNIT AND POWER SWITCH
SWITCH UNIT
1-2. KDL-55HX920/923/925
POWER SWITCH
SWITCH UNIT
CONNECTOR ASSY
SWITCH UNIT
CONNECTOR ASSY
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 40
DISASSEMBLY
1-2-4. HARNESS-1
CONNECTOR ASSY 28P
CONNECTOR ASSY 14P
FLEXIBLE FLAT CABLE
1-2. KDL-55HX920/923/925
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 41
DISASSEMBLY
1-2-5. HARNESS-2
CONNECTOR ASSY 7P
HARNESS ASSY
1-2. KDL-55HX920/923/925
CONNECTOR ASSY 2P
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 42
1-2-6. G7D BOARD
DISASSEMBLY
2
2 Screws (SCREW (+PSW) (M3X6)) P/N: FX0001341
G7D BOARD
INSULATION SHEET
1-2. KDL-55HX920/923/925
G7D BOARD
1
3
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 43
1-2-7. POWER SUPPLY CORD AND G6B BOARD
DISASSEMBLY
2
3
4 Screws (SCREW (+PSW) (M3X6)) P/N: FX0001341
G6B BOARD
INSULATION SHEET
1-2. KDL-55HX920/923/925
G6B BOARD
4
G6B BOARD
5
G6B BOARD
POWER SUPPLY CORD
1
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 44
1-2-8. WIRELESS LAN CARD
DISASSEMBLY
1 2
1 Screw (SCREW (+PSW) (M3X6)) P/N: FX0001341
WIRELESS LAN CARD
1-2. KDL-55HX920/923/925
WIRELESS LAN CARD
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 45
1-2-9. ANTENNA
DISASSEMBLY
1 2
2
ANTENNA
1
1 Screw (SCREW (+PSW) (M3X6)) P/N: FX0001341
ANTENNA
1-2. KDL-55HX920/923/925
ANTENNA
ANTENNA
1 Screw (SCREW (+PSW) (M3X6)) P/N: FX0001341
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 46
1-2-10. SPEAKER BOX ASSY
DISASSEMBLY
1-2. KDL-55HX920/923/925
SPEAKER BOX ASSY
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 47
1-2-11. SPEAKER BOX ASSY (WOOFER)
DISASSEMBLY
1-2. KDL-55HX920/923/925
SPEAKER BOX ASSY(WOOFER)
SPEAKER BOX ASSY(WOOFER)
3 Screws (SCREW, +PSW M3X6 W12) P/N: FX0001901
1 2
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 48
1-2-12. BOTTOM BRACKET
DISASSEMBLY
1-2. KDL-55HX920/923/925
BOTTOM BRACKET
1 2
BOTTOM BRACKET
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 49
1-2-13. SIDE BRACKET AND BATL BOARD
DISASSEMBLY
1 2
3 6 Screws (SCREW (+PSW) (M3X6)) P/N: FX0001341
BATL BOARD
BATL BOARDBATL BOARD
SIDE BRACKET
1-2. KDL-55HX920/923/925
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 50
1-2-14. SHEET
DISASSEMBLY
SHEET (BAT-L METAL BOTTOM)
1-2. KDL-55HX920/923/925
1
2
SHEET (BAT-L METAL SIDE)
SHEET (BAT-L METAL SIDE)
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 51
1-2-15. CAMERA MODULE AND SEALING CAP(CAMERA)
DISASSEMBLY
1 2 3
CAMERA MODULE
1-2. KDL-55HX920/923/925
CAMERA MODULE
CAMERA MODULE5 6
SEALING CAP
SEALING CAP
4
1 Screw (SCREW (+PSW) (M3X6)) P/N: FX0001341
CAMERA MODULE
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 52
1-2-16. HEM2 BOARD
DISASSEMBLY
1 2
3
HEM2 BOARD
1-2. KDL-55HX920/923/925
HEM2 BOARD
HEM2 BOARD
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 53
1-2-17. BOTTOM BRACKET AND SP BRACKET
DISASSEMBLY
1-2. KDL-55HX920/923/925
1 1 1
2 2 2SP BRACKET
SP BRACKET
BOTTOM BRACKET
SP BRACKET
BOTTOM BRACKETSP BRACKET
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 54
1-2-18. FRAME AND JOINT CORNER
DISASSEMBLY
AL FRAME
1-2. KDL-55HX920/923/925
1 2
3
8 Screws (SCREW (+PSW) (M3X6)) P/N: FX0001341HB FRAME
VR FRAMEVL FRAME
HT FRAME HT FRAME
HB FRAME
JOINT CORNERJOINT CORNER
20 Screws (SCREW (+PSW) (M3X6)) P/N: FX0001341
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 55
1-2-19. HLT2 BOARD, PWB (H) TAPE AND PANEL MODULE
DISASSEMBLY
HLT2 BOARD
1-2. KDL-55HX920/923/925
1 2
HLT2 BOARD
PWB (H) TAPE
P-MOD(PANEL MODULE)
INSULATIONSHEET (SW)
HIMERON TAPE (15X60)
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 56
CHASSIS SERVICE000 WYVERN000 S2_NOISE_TH32
Item name
Category name Data
SEC 2. ADJUSTMENT
HOW TO ENTERING SERVICE MODE
1) Turn on the main power switch to place this set in standby mode.
2) Press the buttons on the remote commander as follows, and entering service mode.
3) Service mode display.
Note: First of all, when you enter Service Mode, you can see Digital service mode.Whenever you press OPTIONS or JUMP on remote, each service mode is changed.Digital -> Chassis -> VPC
Press OPTIONSor JUMP button
Item numberCategory number
5DISPLAY TV POWERChannel Volume
DIGITALSERVICE
001OP000VERS
DM1.301W00AARF:01.05WF1.003W00AAWF:2.0.0.99DF1.001W00AAWF:0BYM1.010W00AACAM:X.XXXDB2.105W00AAFD:XXXX(DM1.301W00AA)DD1.016W00AAWP0.521W00AAMID:1C117081PM1.012W00LUPID:04020000PB1.000W00LUPNL:LTY320AB01PL1.011J46LUXPOP:X.XXXPD1.011J46LUX
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 57
ADJUSTMENT
4) How to use the remote commander.
5) After entering service mode, then turn off the power switch.
+/Service mode on
/ Service mode off
/
+
+
+ +
/
/
/
The flow of control
Change module
Write data
Execute
Read data
Test reset
Data up / down
Category up / down
Item up / down
Function
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 58
ADJUSTMENT
WHITE BALANCE ADJUSTMENT
Note: Please execute this adjustment if necessary.
Change Data of VPC service mode. (006 WB category)
a. Press 1 or 4 on remote to select WB adjustment menu.
b. Change data by pressing 3 or 6. Each range of these items is 0~255.
c. Press mute0 on remote to save the data.SERVICE comment is changed to WRITE, indicating writing process.
d. After a while, WRITE comment returns to SERVICE, which means writing process is done..
VPC SERVICE006 WB000 R_DRV 128
VPC SERVICE006 WB001 G_DRV 128
VPC SERVICE006 WB002 B_DRV 128
VPC SERVICE006 WB003 R_BKG 128
VPC SERVICE006 WB004 G_BKG 128
VPC SERVICE006 WB005 B_BKG 128
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 59
ADJUSTMENT
RESTORE WHITE BALANCE / GAMMA ADJ-DATA TO B BOARD
Note: Please apply after USB-DL when B board is replaced.
Change Data of VPC service mode.
a. Select 010 DATA_COPY category by pressing 2 / 5 on remote.
b. Change data from 0 to 1 by pressing 1 / 4 on remote.
c. Wait until data is changed from 1 to 3.
d. When data is changed from 1 to 3, restoring process is finished.
e. In case data is changed from 1 to 2, keep default setting. (No more process is needed)
VPC SERVICE000 DATA_COPY000 BU_TRANS 3
DATATRANSFERSUCCESS
VPC SERVICE000 DATA_COPY000 BU_TRANS 1
DONOTPOWEROFFDONOTTOUCHANYKEYNOW
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 60
SAVE CHANGING DATA
1) Change Data of Chassis or VPC service mode
2) Write data for Chassis or VPC service mode
a. Press Mute on remote.
It shows green SERVICE changes to green WRITE.
b. Press 0 or enter on remote. Green WRITE changes to red WRITE. It indicate writing is processing.
c. After a while, red WRITE changes to green SERVICE. Writing process is done at this point.
3) TV reboot is necessary for applying data change.
ADJUSTMENT
CHASSIS WRITE000 WYVERN000 S2_NOISE_TH32
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 61
DIGITAL(DIG_SRV_MODE)SERVICE
TEST_PATTERN
*1Video2Audio
DIGITAL SERVICE003DIG_SRV_MODE000TEST_PATTERN
DIGITAL SERVICE004TUNER000!A_NOSIG_DET 001
ADJUSTMENT
CHANGE DATA
Note: Digital service mode dont have to Save. (except 002 MODEL and 005 CHAPRESET category)
1) Change Data of Digital service mode. (except 003 DIG_SRV_MODE category)
a. Press 2 / 5 on remote to select (up / down) category.
b. Press 1 / 4 on remote to select (up / down) Item.
c. Press 0 / 10 on remote to select item.
2) Change Data of Digital service mode. ( 003 DIG_SRV_MODE category)
003 DIG_SRV_MODE is one category of Digital service mode.
Please note because this operation is special.
a. Press 2 / 5 on remote to select 003 DIG_SRV_MODE.
b. Press 1 / 4 on remote to select (up / down) Item.
c. Press 0 / 10 on remote to select item.
d. Press number key 1~9 directly. * stamp move.
e. Press 12 / enter / select to decide and advance next step. Press return, when returning on the
previous page.
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 62
ADJUSTMENT
3) Write data for Digital service mode. ( 002 MODEL category)
Note: This procedure operation, when replaced the B board.
Note: Do not write a wrong segment or destination information in Product ID.
When the wrong setting is written, TV may not operate.
000 SEG -----------------Select JDM code information
001 DEST ---------------Select destination information
002 MODELNAME ---Select model name
004 SERIAL ------------ Can be set only once for the new board
a. Change data for each model.
b. Press Mute, 0 on remote sequentially.
It shows red WRITE. It indicate writing is processing.
c. After a while. Red WRITE disappears. Writing process is done after a while.
DIGITAL SERVICE002MODEL000SEG I1
Write
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 63
ADJUSTMENT
SET TO SHIPPING CONDITION
How to do shipping condition.
a. Move to Digital service mode.
Press 8 on remote.
It shows green SERVICE changes to green RST-.
Press mute on remote.
Added green EXE after green RST- .
d. Press 0 on remote. Green EXE-RST changes to red EXE-RST. It indicate writing is processing.
After a while, red EXE-RST changes to green SERVICE.
And all LED lights.
Writing process is done at this point.
You can set to shipping condition w/o entering Service Mode.
-> Cursor Up on remote + Power Key on Front panel.
TIMER Standby POWER
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 64
ADJUSTMENT
CHANGE THE EMITTER OUTPUT LEVEL
Note: To reduce the emitter LED output power strength.
Change Data of VPC service mode
a. Select 005 TD category by pressing 2 / 5 on remote.
b. Select 000 EMIT_STR item by pressing 1 / 4 on remote.
c. Change data from 0 to 1 by pressing 3 / 6 on remote.
0: Strong (Default)
1: Weak
d. Save by pressing Mute + 0 or 10 & Reboot.
VPC SERVICE005 TD000 EMIT_STR 1
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 65
ADJUSTMENT
HDD REC SETTING
DIGITAL(REC_SETTING) SERVICE
REC_SETTING
1KeyCopy*2HDDReRegister
(x)HDDsOK(xx)
HDD Re-Register
a. Press 2 to select HDD Re-Register Item.
b. . Press Enter or 12 twice to execute the command.
c. If OK, xx= x+1If NG, xx=x
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 66
SEC 3. TROUBLE SHOOTING
3-1. TRIAGE CHART
Note: Power board is different in name every inch. Therefore this section displays difference point in "*".
NoPower Remote Network Audio Skype
2 3 4 5 6 7 8 10No Green
Power LED(Dead Set)
Stationarycolored lines
or dots
No videoone of Inputs
No videoall Inputs
NoRemote
Wirelesscan't
connectNo Audio
SkypeCan't Work
BATL BOARDG* BOARDHLT2 BOARDSPEAKERSkype MODULEWIFI MODULELD BOARDLVDS CABLET-CONLCD PANEL
Problem POWERPOWERAUDIO
POWER PANEL(TCON)PANEL
(INVERTER)TEMP Software EMITTER
: doubtful part
: Few possibility
Reference
Video - missing or distortedSymptoms - Shutdown. Power LEDblinking red diagnostics sequences
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 67
TROUBLE SHOOTING
3-2. FLOW CHART
START
Does the Power Ledstay on when the
TV is switched on ?
Is the Standby Ledblink ?
Is the Picture andSound OK ?
END
SeeNo Power
SeeStandby LED Blink
SeeNo Picture / No Sound
Is the networkconnection OK?
SeeCant connect network
No
Yes
Yes
No
No
Yes
Is the camerafunction OK?
SeeCamera malfunction
No
Yes
See3D malfunction
No
Yes
Is the 3Dfunction OK?
Do the buttonson the TV & Remote
Commander workproperly?
SeeTV/ Commander button malfunction
NoNo
Yes
No
Yes
SeeSkype malfunction
NoIs the Skypefunction OK?
Yes
SeeHDD Rec malfunction
NoIs the HDD Recfunction OK?
Yes
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 68
TROUBLE SHOOTING
3-3. NO POWER
No Power
Check STBY 3.3Vat pin 10 of CN6001
on the B* Board
Harness
G* BoardReplace
Between G* Board toB* Board Harness
B* Board
NG
OK
NG
OK
Turn on the SwitchCheckPower Saving Switch
SW OFF
SW ON
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 69
1) 2 times blinking (Main Power Error)
TROUBLE SHOOTING
3-4. STANDBY LED BLINK
2 times blinking
Check REG12V atpins 2/3 ofCN6001 on
the B* Board
B* Board Harness
G* BoardReplace
Between G* Board toB* Board Harness
12V NG
12V OK
NG
OK
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 70
TROUBLE SHOOTING
2) 3 times blinking (DC Alert, Audio Error and Communication Error)
3 times blinking
Check D+1.2V atpin 14 of IC6005on the B* Board
F6001,IC6005,etc(B* Board)
Speaker
Check +3.3V_MAINat pins 9/10 of CN9003
the B* Board
CheckSpeaker Impedance
at SP Connector
F6003,IC6003,etc(B* Board)
Check AUDIO+12.5Vat pins 8/9 ofCN6001 on
the B* Board
G* Board
Check +12.5Vat F4601 on
the B* Board
F4601,IC4601,etc(B* Board)
IC4601,etc(B* Board)
DC_ALERT
NG
OK
AUDIO
AUDIO
FE/BE Communication
NG
OK
NG
OK
NG
OK
NG
OK
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 71
TROUBLE SHOOTING
3) 4 times blinking (Including SPI Error)
4-time blinking
Panel
B* Board
Between 0.84V to 2.65V
Change G* Board G* Board
Below 0.84V
Symptom improvement
NG
Change LED Driver Board LED Driver Board
Symptom improvement
Check the harness betweenthe T-con board and
the LED driver board,between the G board and
the LED driver board.
Harness
NG
Change T-CON Board T-con Board
NG
Symptom improvement
CheckPANEL_FAIL atpin 7 of CN6002on the B* Board
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 72
TROUBLE SHOOTING
4) 5 times blinking (T-con Error)
5-time blinking
Check PANEL_VCCat pin 1 of
CN6001 onon the B* Board
G* Board
Replace the Harness Between G* and Panel
Replacethe LVDS Harness
Panel (T-con)change B* BoardHarness
LVDS Harness Panel (T-con)
12V NG
12V OK
NG
Symptom improvement
Symptom improvement
Symptom improvement
NG
NG
RGB sensor Change RGB Sensor
Symptom improvement
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 73
TROUBLE SHOOTING
5) 6 times blinking (Backlight Error)
6-time blinking
Checkthe harness between
the T-con board and theLED driver board.
Harness
Change G* board G* Board
NG
Light Source(Inside Panel Module)
Change LED driverboard LED Driver Board
NGCheck FFC connection betweenthe LED driver board and
the light source (inside the panel module)
FFC Connection
NG
NG
OK
OK
Symptom improvement
Symptom improvement
Change B*board B* Board
Symptom improvement
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 74
TROUBLE SHOOTING
6) 7 times blinking (Temperature Error)
7 times blinking
Setting circumstanceis OK?
Temperature,Ventilation, etc.
Set to anotherLocation, etc.
NO
YES
Change B* Board,and Aging a few hours
B* Board
OK
Panel
7) 8 times blinking (Software Error)
8 times blinking
If the SymptomImproved by changing
the WIFI moduleB* Board
NO
WIFI Module
YES
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 75
TROUBLE SHOOTING
8) 10 times blinking (Emitter Error)
10 times blinking
Checkthe harness betweenthe T-con Board and
the HEM2 Board
Harness
NG
OK
Change HEM2 Board
HEM2 Board
OK
T-CON Board
NG
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 76
3-5. NO PICTURE
No Picture
Press HOME KeyOSD displayed?
Replace the B-T-con,T-con-LD* FFC
G* Board
Check the G*-LD* Harness
No
Change B* Board
Change G* Board
B* Board Harness B-T-con,T-con-LD* FFC B* Board
LCD Panel(T-con, LD*)
Yes
OK
NG
NG
OK
NG
OK
NG
OK
TROUBLE SHOOTING
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 77
TROUBLE SHOOTING
3-6. NO SOUND
No Sound
Check the SpeakerHarness
Speaker Harness
Replacethe B* Board B* Board
Speaker
OK
NG
NG
OK
Check the Speakers setting
Change to TV Speaker
Audio System
TV Speakers
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 78
3-7. TV COMMANDER BUTTONS MALFUNCTION
TROUBLE SHOOTING
1) TV button malfunction
Button malfunctionon the TV
Replace the Harnessbetween B* toSwitch Unit
Switch Unit
Harness
Switch Unit change
B* Board
OK
NG
OK
NG
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 79
TROUBLE SHOOTING
2) IR remote commander malfunction
TV isnt controlled by remote commander
Green LED lightat power indicator
OK
NG
Sensor is broken
HLR Board
B* Board
OK
NG
Mechanical(ex. bezel)
Green LED blinksat power indicator
when using commandernear sensors window
Check the Harnessbetween the B* Board
and the HLR Board
Exchange the Harness
Exchange theHLR Board
Harness
OK
NG
OK
OK
NG
NG
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 80
TROUBLE SHOOTING
3-8. NETWORK MALFUNCTION
1) Wired Network malfunction
Wired Networkon the TV
Connection resultLocal Access
Connection resultCable Connection
OK
NG
OK
NG
Connection resultInternet Access Proxy setting
NG
B* Board
Check the Ethernet Cable Ethernet Cable
Check IP addressand Local router setting
Wired Set-upIP address setting Check Local router DHCP server
Auto
Manual
OK
NG
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 81
TROUBLE SHOOTING
2) USB Wireless Network malfunction
Wireless Networkon the TV
Is the radio field Strength too weakor even No signal?
Access Point
B* Board
Error Message appearwhen the Wireless
Network is selected?USB Dongle
NO
YES
NO
YES
3) Internal Wireless Network malfunction
Wireless Networkon the TV
Is the radio field Strength too weakor even No signal?
Access Point
B* Board
Error Message appearwhen the Wireless
Network is selected?Wireless Module, Harness
NO
YES
NO
YES
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 82
3-9. CAMERA MALFUNCTION
TROUBLE SHOOTING
Enter Presence sensor settings
Error Message appearwhen the Presences
Sensor setting?
Module optical problem(change module)
Module, Harness
Is image is clear onsetting menu
at module unit only?
MechanicalProblem
Yes
No
Presence Sensor Setting:Press HOME, then select > System Settings > Eco > Presence Sensor
Yes
No
Error message
image
Setting Menu
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 83
3-10. 3D MALFUNCTION
TROUBLE SHOOTING
3D malfunction
HEM2 Board
No
No
NG
Yes
Change Watching environment
Panel (T-con)
[How to confirm IR-output.]ex) Look IR-LED through CCD/CMOS camera.
IR has been outputon HEM board,
during 3D displaying.
Replace HEM2 board
Symptom improvement
Check whether there is
interception thing between Emitter
and glasses.No
YesYesIs 3D glasses
power on?
Power on or
Charge battery
3D glasses
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 84
Skype malfunction
USB plugged? Insert USB
Able to run Skype App?
Spec. USB overload.
Connect to other USB port
B* board
Insert other Skype unit or
USB dongle
Skype unit
B* board
Network connected? Do network setup
Yes
No
Yes
No
No
OK
NG
OK
NG
OK
NG
Next page
Yes
3-11. Skype MALFUNCTION 1/2
-Unplug other USB device-AC OFF/ON
TROUBLE SHOOTING
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 85
Far end Video/Audio quality?
Network speedor
far end system issue
Auto-Focus work? Sound quality?No video?
Manual Focus work?
Check Auto-Focus area
Enough network speed?
Skype unit
Call Skype sound test
Far end setting/system
Move unit away from speaker
Skype unit
Audio problem
Video problem
Previous page
OK NG
Yes
No
Yes
No
No
Yes
Yes
NG
3-11. Skype MALFUNCTION 2/2
TROUBLE SHOOTING
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 86
3-12. HDD-Rec MALFUNCTION
TROUBLE SHOOTING
HDD RecMalfunction
B board
HDD is connectedto the appropriate
USB port?
Connect to theappropriate port
No
Yes
USB Hub is insertedin between the
USB port and HDD?
USB Hub isnot supported
Yes
No Is the drive size largerthan 32GB and
Smaller than 2TB??
Only 32GB~2TBis supported
No
Yes
All the setups and restrictions listed in iManual are cleared?
Check the iManualNo
Yes
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 87
SEC 4. DIAGRAMS
4-1. BLOCK DIAGRAM
CableSatellite
Terrestrial
HDMI1(ARC)
HDMI2
HDMI3
HDMI4
SCART Conversion
ComponentConversion
PC
SPDIF
HP/Line Out
AssistSPEAKER
MainSPEAKER
Analog VideoDigital Video/TS/TMDS
Analog AudioUARTDigital Audio
Analog SignalPWM
I2CSPI
X_AUDIO_MUTE1X_AUDIO_MUTE2
X_FAULT
Main Speaker_Out_LR
Assist Speaker_Out
X_SYSTEM1_RST
SPDIF
HP/Line Out LRHP_/ Line Out Det
PC_R,PC_G,PC_B,PC_H,PC_VPC_LR
PC_5V, PC_DDC
PC_CON_Det
COMP_LRVideoB_Det
TV_Out
Scart_CV,R,G,B,FBScart_LR
TV_Out_LR
ASPECT1
CEC3
DDC4
HPD4
CEC4
DDC_5V_4
TMDS4
CEC2
DDC3
HPD3DDC_5V_3
TMDS3
TMDS2DDC2
HPD2DDC_5V_2
TMDS1DDC1
HPD1
CEC1
DDC_5V_1
ARC
Silicon Tuner
X_SYSTEM1_RST
Xtal
LNA
SW
Xtal
LNASilicon Tuner
IF1
IF2
Zero-IF
27MHz
Ext DemodIFAGC
Ext DemodIFAGC
Xtal
TS1
TS2
DiSEqC_OutDiSEqC_In DDC
I2CB
I2CB
DMD_RSTDMD_CLK_ENABLE1DMD_CLK_ENABLE2
CI/CI+
5
V
Current Limit
MS H Con.
USB3Wifi
USB4Camera
USB2
Current Limit
USB1
5
V
Current Limit
5
V
X
_
S
Y
S
T
E
M
1
_
R
S
T
USB HUB
Crystal
X
_
S
Y
S
T
E
M
1
_
R
S
T
Ether
EtherPHY
LVDS_ODDLVDS_EVEN
TCON
PEH2
I
2
C
_
C
D
L
_
C
S
D
L
_
C
L
K
D
L
_
D
O
P
E
M
_
L
O
G
_
T
X
U
A
R
T
D
_
R
X
/
F
E
_
R
X
_
P
E
M
_
T
X
U
A
R
T
D
_
T
X
/
F
E
_
T
X
_
P
E
M
_
R
X
P
E
M
_
L
O
G
_
R
X
S
A
_
M
O
D
E
/
L
U
T
_
S
E
L
0
P
E
M
_
W
D
T
/
X
B
U
S
Y
/
B
I
N
T
X
_
P
E
M
_
R
S
T
/
L
U
T
_
S
E
L
2
/
X
_
F
R
C
_
R
S
T
M
O
D
E
_
P
E
M
/
T
C
O
N
_
R
D
Y
T-CON_VCC (12V)
P
o
w
e
r
STBY 3.3V
T-CON_VCC
REG12V
AUDIO_12VAUDIO_12V
REG12V
REG_12V1.2V
DDC
SYSTEM1_PWR
1.5V
SYSTEM2_PWR
DDC
SYSTEM2_PWR
DDC3.3V
2.5VLDO
SYSTEM2_PWR
REG_12V5V
DDC REG_12V
SYSTEM2_PWR
S1.8VLDO
3.3VLDO
S1.2VLDO
3.4VLDO
MAIN_PWR
BACKLIGHT_ONDIMMER
BACKLIGHT_MON
PFC_PWRAC_MON
DIMMER_DCTCON-ON
P
o
w
e
r
_
C
o
n
t
r
o
l
UARTA(LOG)
UARTC(Hotel/ECS)
UARTD
PEM_LOG
I2CA(Hotel_Clock)
MODE_PEMReset
SIRCS
DIMMER2
T
L
-
J
I
G
H
o
t
e
l
/
E
C
S
Temp SensorTemp
SensorI2CA
X_Hotel_PWR_CTRL
Xtal
Xtal
AC_MON
Reset
Reset
/RST
JTAG
I2CA (EQSW, Temp Sensor, Hotel Clock)I2CB (Ext Demod)I2CC (Panel, RGB Sensor)
UARTA (LOG)
UARTD (PEM)
UARTB (RF-Remote)UARTC (IR Blaster/ECS)
Tuner_Sig_Det
DIMMER
LOGODIMMER_DCDMD_CLK_ENABLE2
DEBUG_LED2
DEBUG_LED3
DMD_RSTDMD_CLK_ENABLE1PANEL_PWR
HP_DETX_WIFI_RST
X_AUDIO_MONHDMIEQ_INT
SPDIF_SEL
UARTB
Power_KEY
KEY
X_RF_RST
SIRCS
UARTE
RF Remote
KEY
Sircs
Human SensorLight SensorRGB Sensor
LED
LOGO
Light_Sensor_Det
Human_Sensor_Det
I2CC
STBY_LEDPOWER_LED
TIMER_LED
PIC_MUTE_LEDREC_LED
LOGO
3D_CON_DetDC_M
ON
KE
Y
Light_Sensor_D
et
ASPE
CT1
Hum
an_Sensor_D
etP
AN
EL_S
EL
BA
CKLIG
HT_M
ON
PAN
EL_P
WR
_Det
AC_M
ON
PFC
_MO
NP
OW
ER_K
EY
DE
BUG
_LED1
STB
Y_LE
DTIM
ER
_LED
MA
IN_P
WR
MA
IN_SS_M
ON
SY
STE
M2_PW
RS
YS
TEM
1_PWR
PIC
_MU
TE_LED
X_RF_R
STX
_HO
TEL_PW
R_C
TRL
PO
WE
R_LE
DR
EC_LE
DX_SYSTEM
1_RST
PFC
_PW
RX
_AU
DIO
_MU
TE1
X_A
UD
IO_M
UTE
2
PC
_CO
N_D
ET
VIDE
OA
_DET
VIDE
OB
_DE
TC
R_D
ET
BA
CKLIG
HT_O
NN
MI
X_FRC
_RST
SA
_MO
DE
LR_FLA
G
FRC
_PWR
_CTR
L
TCO
N_R
DY
DA
TA1
BIN
T Panel less
PanellessX_SYSTEM1_RST
AUDIO_MON
OPAMP
AudioPower AMP
AudioPower AMP
Main Speaker_Out_LR
Atreyu_SPDIF
Assist Speaker_Out_LR
OPAMP[NJU72040V]
TV_Out_LRTuner_LR
Line Out_LR
PC_LRCOMP_LR
AV3_LR
Scart1_LRTuner_LR
PC_GPC_BPC_RPC_HPC_V
COMP_YCOMP_PbCOMP_Pr
Scart_CVScart_GScart_BScart_R
Scart_FB
Select_Out
COMP_Y
TV_Out
75Drv
TMDSDDCCEC
Xtal
IF1
TSEQ SW
I2CA
3.3->1
Atreyu
REG_12V
27M
4M
41M
41M
12M
48MPush
32.768K
GND
00
[HORUS3]
[ASCOT2Sip]
[SEKITO2]
[ZHUI]
[Sil9287B]
[LNBH23]
[NJM2561]
[NJU72011RB]
[TPS2553DBV]
[GL850G]
[TPS2553DBV]
[RTL8201E]
OneNANDMuxed
2Gb
DDR313332Gb
DDR313332Gb
[PST3629]
[LM75B]
PANEL
SONY
H / L
[D510D]
[D510D]
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 88
DIAGRAMS
4-2. CONNECTOR DIAGRAM
4-2-1. KDL-46HX920/923/925 (1/2) (Only Interface between board and board)
CN03
PJWW041DNG
To BATSC_LD151SC_LD : 1lrtC_lenaPDNG IFIW185
832OGOL
XR_GOL_MEP052XR_GOL_MEP : 2lrtC_lenaPSUBV IFIW242CN3eludom noitanimulli OGOL YNOS
KCS_LD943KLC_LD : 3lrtC_lenaPP_BSU IFIW363934V5URHTARUSA/1-a3/2-b2/1-b2/a1
CN041-820-181-11TSR_MEP_X844Panel_Ctrl4 : X_PEM_RST/LUT_SEL2/X_FRC_RSTDNG411
GALF_RL / IS_LD745OD_LD : 5lrtC_lenaPN_BSU IFIW574 (For Asura)EDOM_AS6460LES_TUL/EDOM_AS : 6lrtC_lenaPDNG IFIW65
XT_GOL_MEP547XT_GOL_MEP : 7lrtC_lenaPTSR IFIW7CN CN05Panel_Ctrl8 : UARTD_RX/FE_RX_PEM_TXSUBV AREMAC81 XR_MEP_EF448
TDW_MEP / TNIB349TNIB/YSUBX/TDW_MEP : 9lrtC_lenaPP_BSU AREMAC93631DNG
Panel_Ctrl10 : UARTD_TX/FE_TX_PRM_RXDNG AREMAC014332TNI_REWOPeludom WS
XT_MEP_EF2401ADS1411ADS_CC2I : 11lrtC_lenaPN_BSU AREMAC112
5331YEKLLACN061-822-693-11
LCS0421LCS_CC2I : 21lrtC_lenaPDNG AREMAC215nip65 CFF 11NCnip65 CFF 11NCDNG9331DNGDNG FR313
+2ER8341P_4NEVE_LENAPxR FR415 1-822-905-11 1-822-905-11DNG-2ER7351N_4NEVE_LENAPTSR FR512 11 BL_TYPE31MWP-1+2DR6361P_3NEVE_LENAPxT FR614 22 BL_TYPE22MWP-1-2DR5371N_3NEVE_LENAPV3.3YBTS FR716
921V3.3+YBTS
33 BL_TYPE13MWP-1DNG4381DNGLES_TRAU FR811
722DNGrosneS_TPO/rosneS BGR/RI/DEL
44 REF4MWP-1+2KLCR3391P_KLC_NEVE_LENAPREMIT_NO_DEL RLH915
523CER_DEL1-b2
55 FAIL5MWP-1-2KLCR2302N_KLC_NEVE_LENAPSCRIS RLH0201
124YBTS_DEL2-b2
66 LED_ON6MWP-1DNG1312DNGYBTS_DEL RLH124
915REMIT_DEL1-a3
77 LD_STDBY7MWP-1+2CR0322P_2NEVE_LENAPADS_ECIVED RLH2211
326REWOP_DEL
88 NC8MWP-1-2CR9232N_2NEVE_LENAPREWOP_DEL RLH326
627ETUM_CIP_DEL
99 12VDNG+2BR8242P1NEVE_LENAPLCS_ECIVED RLH4221
CN8SNES_TPO
0101 NCCPM_DELV-2BR7252N_1NEVE_LENAPCER_DEL RLH523
039V3.3+DV
1111 GND1MWP-2+2AR6262P_0NEVE_LENAPETUM_CIP_DEL RLH627
0201SCRIS
2121 NC2MWP-2-2AR5272N_0NEVE_LENAPDNG RLH722
2211ADS_ECIVED
13 56pin FFC 13 NC3MWP-2DNG4282DNGSNES_TPO RLH82CN
4221LCS_ECIVED
4141 TCON_VCC1-821-139-114MWP-2+1ER3292P_4DDO_LENAPV3.3_YBTS RLH921 5151 NC5MWP-2-1ER2203N_4DDO_LENAPV3.3 RLH039 6161 NC6MWP-2+1DR1213P_3DDO_LENAPV3.3 YBTS WS13CN 7171 GND7MWP-2-1DR0223N_3DDO_LENAPTED_YEK_WS23CN 8181 5_SPI_RDATAF8MWP-2DNG9133DNGYEK_REWOP_WS332
811CNYS
9191 5_SPI_LATFDNG+1KLCR8143P_KLC_DDO_LENAPTSR_YEK_WS43CN
512TESER
0202 5_SPI_DATAFEPYT_DL-1KLCR7153N_KLC_DDO_LENAPYEK_WS533
313DNGeludom CRFR
1212 5_SPI_CLKF1MWP-3DNG6163DNGDNG WS631
614XR1-P/2-a3/1-a3/3-b2/2-b2/1-b2
2222 5_EMIT_IN2MWP-3+1CR5173P_2DDO_LENAPV0.5_DV WS73CN
415XTnapaJ ylno
3232 4_SPI_RDATAF3MWP-3-1CR4183N_2DDO_LENAPOGOL YNOS832
716DDV
4242 4_SPI_LATFJAM SYT10-06-WL-ET
4MWP-3+1BR3193P1DDO_LENAPV5 OGOL934 5252 4_SPI_DATAF1-821-146-11
5MWP-3-1BR2104N_1DDO_LENAPDNG OGOL041 6262 GNDCN9006 6MWP-3+1AR1114P_0DDO_LENAP 7272 GND1-818-692-21 7MWP-3-1AR0124N_0DDO_LENAP 8282 4_SPI_CLKF
8MWP-3DNG934DNGP04 YLBNESSA REDAEH 9292 4_EMIT_INDNGDNG844DNG 0303 3_SPI_RDATAFDNGEDOM_TOOB754YDR_NOCT/MEP_EDOM :31lrtC_lenaP 1313 3_SPI_LATF
or
1MWP-4CN664DNG 2323 3_SPI_DATAF2MWP-4V21574WS_CCV_LENAP 3333 3_SPI_CLKF3MWP-4V21484WS_CCV_LENAP
41DNG41DNG
4343 3_EMIT_IN4MWP-4V21394WS_CCV_LENAP
CN2DNG22CCV IFIW
5353 2_SPI_RDATAF
WIFI USB_P 3 3 or
5MWP-4V21205WS_CCV_LENAP
CN3CCV IFIW
6363 LD_TYPE6MWP-4V21115WS_CCV_LENAP
24CCV IFIW54M_BSU IFIW
7373 GND
65DNG15DNG IFIW
4-PWM7 8383 2_SPI_LATF
36P_BSU IFIWBT-SHG-B50MS
1-842-546-11 4-PWM8 9393 2_SPI_DATAF
57M_BSU IFIW11-433-918-1
GND 0404 2_SPI_CLKF
GND 8 1
NC 1414 2_EMIT_IN
SM08B-GHS-TB
NC 2424 1_SPI_RDATAF
1-819468-11
TCON_VCC 3434 1_SPI_LATFNC 4444 1_SPI_DATAFNC 5454 1_SPI_CLKF
DNG 6464 VLED_MPCNC 7474 GND
CAMERA VBUS 1 8
12V 8484 1_EMIT_IN
112N_BSU AREMACeludom CRFR
NC 9494 0_SPI_RDATAF
93P_BSU AREMAC2/x-a3
LD_STDBY 0505 0_SPI_LATF
014DNG AREMACnapaJ ylno
NO_DEL 1515 0_SPI_DATAF
CAMERA GND 5 12
LIAF 2525 0_SPI_CLKF
MOLEX 501940-0507
FER 3535 0_RESET_IN
1-820-182-11
1EPYT_LB 4545 0_EMIT_IN2EPYT_LB 5555 0_READY_O3EPYT_LB 6565 GND
SPEAKERFrontLch
L+ (Fasten # 187) +L1111L- (Fasten #110) 2 2 2 2 L-
2 3 R-1 4 R+1 5 L+3 6 L-SPEAKER
FrontRch
R- (Fasten # 110) 2 rotcennoC rekaepS gnisuoH3R+ (Fasten # 187) 1 4 2.1ch: 6pin 0-844-427-01 JST PBVP-06V 2.1ch: CN4602 6pin 0-844-174-01 JST SM06B-PBVSS-TB(LF)(SN)
SPEAKERASSISTLch
L+ 1 5NC 2L- 3 6
Refer to Sheet [ Appendix SP Connector ]
LEDFFC40pin
CN2001
FFC Direct in Connector :I-PEX
LEDFFC40pin
PANEL FFCSLCD : 68pin
SHARP : 80pinAUO : ??pin
CMI :32" 37" 60 pin40" 55" 80pin
LEDFFC40pin
LEDFFC40pin
V3.3YBTS11DXR_232SR22DXT_232SR33TUO_SCRIS44
NI_SCRIS55DNG66
5009NC113311281 rotcennoc nip6
51pin FFC
LVDS-FFCB-PYL
LD - TC - HarnessTCON - LD
BAT-L board
SW module
BL- H HarnessH - B
LOGO module
HLT2 board
CAMERA module
Wifi module(WW)
Wifi module(JP)
LD DirectBoard
STBY3.3V 1 1RS232_RXD 2 2RS232_TXD 3 3SIRCS_IN 4 4SIRCS_OUT 5 5GND 6 6CN101182018311
R3 or RU board
RFRC module
(JST)
T-con Board(PEH2)
[2b-1 46 1/2]
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 89
DIAGRAMS
4-2-1. KDL-46HX920/923/925 (2/2)
11V2122V21rettimE D333DNGV-a344DNG55LRTC_SLG
GLS_CTRL2 6 6EMI_FAIL 7 7
88CN1-821-135-11
CN6151 SJM20-28WLB
G5B To B board (100106)T-CON_Vcc12V 28 1GND 27 3T-CON_VCC12V 26 2GND 25 4T-CON_VCC_12V To B 24 NCGND 23 NCBDR_ASU_12V 22 NCGND 21 NCBDR_ASU_12V 20 NCGND 19 NCREG12V 18 2GND 17 4REG12V 16 3GND 15 5AU_12V 14 8AU_GND 13 6AU_12V 12 9AU_GND 11 7STBY3.3V 10 10GND 9 1T-CON_ON 8 3AC_OFF_DET 7 9BL_ERR 6 7NC 5 NCNC 4 NCPFC_ON 3 2NC 2 NCPOWER_ON 1 8
VLED_VCC 1 1VLED_VCC 2 2VLED_VCC 3 3VLED_VCC 4 4NC 5 5VLED_GND 6 6VLED_GND 7 7VLED_GND 8 8VLED_GND 9 9VLED_GND 10 10LD_ERR 11 11NC 12 12GL_CTRL 13 13LED_ON 14 141-822-339-11JST XA 14PCN6801
AC_INAC-N 1 1AC-L 2 2CN6001SFP79-02WLB JAM1-822-908-11
Energy_Saving_SWAC(N)-IN 1 1AC(L)-IN 2 2CN6002SFP79-02WLB JAM1-822-908-11
Energy_Saving_SWAC(L)-OUT 1 1AC(N)-OUT 2 2CN6003SFP79-02WLB JAM1-822-908-11
HEM2 Board
TC-EM HarnessPEL3-HEM2
ES SW
B board
T-con
Option
G-B Harness
LD board
T-con
B board
AC pigtail
BAT-L board
CN60011-821-620-11HEADER ASSEMBLY FOR PWB 10P
V3.3+_YBTS010112 V5.21+OIDUA9
V5.21+OIDUA84111 DNG_V5.21+OIDUA7
DNG_V5.21+OIDUA63115 DNG_V5.21+GER5
DNG_V5.21+GER47116 V5.21+GER3
V5.21+GER281NC CCV_NOC-T1
2006NC11-955-248-1
7 9 AC_OFF_DET1 8 POWERON6 7 BL_ERR
NC 6 NCNC 5 NCNC 4 NC
NO_NOCT383 2 PFC_PWR9 1 GND
1DNG2XT_DTRAU3XR_DTRAU4TESER5V3.3+_YBTS6MVT_EDOM7XR_ATRAU8)2DM( CN9XR_CTRAU01XT_CTRAU11DNG21XT_ATRAU31XIRTAM_SCE41V3.3+_YBTS51MEP_EDOM61XR_GOL_MEP71XT_GOL_MEP81DNG
4009NC15-766-477-1
P81 CPF/CFF,rotcennoC 1XE-LT
TL-EX1JIG board
LD DirectBoard
14pin connectorYEONHO 20022WR-14AML
1 1 VLED_VCC2 2 VLED_VCC3 3 VLED_VCC4 4 VLED_VCC
NC 5 5 NC6 6 VLED_GND7 7 VLED_GND8 8 VLED_GND9 9 VLED_GND
10 10 VLED_GND11 11 LD_ERR
NC 12 12 NC13 13 GL_CTRL14 14 LED_ON
(Only Interface between board and board)
T-con Board(PEH2)
28 1 12V26 2 12V27 3 GND
DNG452JST(VA)1-842-566-11
V2111V2122DNG33DNG44
LRTC_SLG552LRTC_SLG66
LIAF_IME77CN88
Molex1-842-558-11
[2b-1 46 2/2]
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 90
DIAGRAMS
4-2-2. KDL-55HX920/923/925 (1/2)(Only Interface between board and board)
CN03
PJWW041DNG To BAT 1lrtC_lenaPDNG IFIW185832OGOL : SC_LD151SC_LD
SONY LOGO illumination module 2lrtC_lenaPSUBV IFIW242CN3 : XR_GOL_MEP052XR_GOL_MEP 3lrtC_lenaPP_BSU IFIW363934V5URHTARUSA/1-a3/2-b2/1-b2/a1 : KCS_LD943KLC_LD CN04
1-820-181-11 4lrtC_lenaPDNG411 : TSR_MEP_X844TSR_CRF_X/2LES_TUL/TSR_MEP_X 5lrtC_lenaPN_BSU IFIW574 : GALF_RL / IS_LD745OD_LD (For Asura) 6lrtC_lenaPDNG IFIW65 : EDOM_AS6460LES_TUL/EDOM_AS 7lrtC_lenaPTSR IFIW7CN : XT_GOL_MEP547XT_GOL_MEP CN05 8lrtC_lenaPSUBV AREMAC81 : XR_MEP_EF448XT_MEP_XR_EF/XR_DTRAU
GND 1 36 9lrtC_lenaPP_BSU AREMAC93 : TDW_MEP / TNIB349TNIB/YSUBX/TDW_MEP 332TNI_REWOPeludom WS 01lrtC_lenaPDNG AREMAC014 : XT_MEP_EF2401XR_MRP_XT_EF/XT_DTRAU 5331YEKLLA 11lrtC_lenaPN_BSU AREMAC112 : ADS1411ADS_CC2I CN06
1-822-693-11 21lrtC_lenaPDNG AREMAC215 : I2CC_SCL LCS0421nip65 CFF 11NCnip65 CFF 11NCDNG9331DNGDNG FR313
+2ER8341P_4NEVE_LENAPxR FR415 1-822-905-11 1-822-905-11DNG-2ER7351N_4NEVE_LENAPTSR FR512 11 BL_TYPE3 CN071MWP-1+2DR6361P_3NEVE_LENAPxT FR614 22 BL_TYPE2
STBY+3.3V 1 29 2MWP-1-2DR5371N_3NEVE_LENAPV3.3YBTS FR716 33 BL_TYPE1LED/IR/RGB Sensor/OPT_Sensor GND 2 27 3MWP-1DNG4381DNGLES_TRAU FR811 44 REF
523CER_DEL1-b2 4MWP-1+2KLCR3391P_KLC_NEVE_LENAPREMIT_NO_DEL RLH915 55 FAIL124YBTS_DEL2-b2 5MWP-1-2KLCR2302N_KLC_NEVE_LENAPSCRIS RLH0201 66 LED_ON915REMIT_DEL1-a3 6MWP-1DNG1312DNGYBTS_DEL RLH124 77 LD_STDBY CN03
LED_POWER 6 23 7MWP-1+2CR0322P_2NEVE_LENAPADS_ECIVED RLH2211 88 NCLED_PIC_MUTE 7 26 8MWP-1-2CR9232N_2NEVE_LENAPREWOP_DEL RLH326 99 12VOPT_SENS 8 NC DNG+2BR8242P1NEVE_LENAPLCS_ECIVED RLH4221 0101 NCVD+3.3V 9 30 CPM_DELV-2BR7252N_1NEVE_LENAPCER_DEL RLH523 1111 GND CN04SIRCS 10 20 1MWP-2+2AR6262P_0NEVE_LENAPETUM_CIP_DEL RLH627 2121 NCDEVICE_SDA 11 22 2MWP-2-2AR5272N_0NEVE_LENAPDNG RLH722 13 56pin FFC 13 NCDEVICE_SCL 12 24 3MWP-2DNG4282DNGSNES_TPO RLH82CN 4141 TCON_VCC1-821-139-11 4MWP-2+1ER3292P_4DDO_LENAPV3.3_YBTS RLH921 5151 NC CN05
5MWP-2-1ER2203N_4DDO_LENAPV3.3 RLH039 6161 NC6MWP-2+1DR1213P_3DDO_LENAPV3.3 YBTS WS13CN 7171 GND7MWP-2-1DR0223N_3DDO_LENAPTED_YEK_WS23CN 8181 5_SPI_RDATAF
SYNC 1 18 8MWP-2DNG9133DNGYEK_REWOP_WS332 9191 5_SPI_LATF CN06RESET 2 15 DNG+1KLCR8143P_KLC_DDO_LENAPTSR_YEK_WS43CN 0202 5_SPI_DATAF
313DNGeludom CRFR EPYT_DL-1KLCR7153N_KLC_DDO_LENAPYEK_WS533 1212 5_SPI_CLKF614XR1-P/2-a3/1-a3/3-b2/2-b2/1-b2 1MWP-3DNG6163DNGDNG WS631 2222 5_EMIT_IN415XTnapaJ ylno 2MWP-3+1CR5173P_2DDO_LENAPV0.5_DV WS73CN 3232 4_SPI_RDATAF CN07
VDD 6 17 3MWP-3-1CR4183N_2DDO_LENAPOGOL YNOS832 4242 4_SPI_LATFJAM SYT10-06-WL-ET 4MWP-3+1BR3193P1DDO_LENAPV5 OGOL934 5252 4_SPI_DATAF1-821-146-11 5MWP-3-1BR2104N_1DDO_LENAPDNG OGOL041 6262 GND
6MWP-3+1AR1114P_0DDO_LENAP6009NC 7272 GND CN081-818-692-21 (JST) 7MWP-3-1AR0124N_0DDO_LENAP 8282 4_SPI_CLKF
8MWP-3DNG934DNGP04 YLBNESSA REDAEH 9292 4_EMIT_INDNGDNG844DNG 0303 3_SPI_RDATAF
Panel_Ctrl13 : DNGEDOM_TOOB754YDR_NOCT/MEP_EDOM 1313 3_SPI_LATF CN09
or 1MWP-4CN664DNGV3.3YBTS11 2323 3_SPI_DATAF2MWP-4V21574WS_CCV_LENAPDXR_232SR22 3333 3_SPI_CLKF
GND 1 4 GND 1 4 3MWP-4V21484WS_CCV_LENAPDXT_232SR33 4343 3_EMIT_INWIFI VCC 2 2 GND 2 NC 4MWP-4V21394WS_CCV_LENAPTUO_SCRIS44 5353 2_SPI_RDATAF CN10WIFI USB_P 3 3 or WIFI VCC 3 NC 5MWP-4V21205WS_CCV_LENAPNI_SCRIS55 6363 LD_TYPEWIFI USB_M 4 5 WIFI VCC 4 2 6MWP-4V21115WS_CCV_LENAPDNG66 7373 GNDWIFI GND 5 1 GND 5 6 CN9005 4-PWM7 8383 2_SPI_LATF
36P_BSU IFIWBT-SHG-B50MS 6pin connector 182113311 1-842-546-11 8MWP-4 9393 2_SPI_DATAF CN1157M_BSU IFIW11-433-918-1 DNG 0404 2_SPI_CLKF
GND 8 1 NC 1414 2_EMIT_INSM08B-GHS-TB NC 2424 1_SPI_RDATAF1-819468-11 TCON_VCC 3434 1_SPI_LATF CN12
NC 4444 1_SPI_DATAFNC 5454 1_SPI_CLKF
GND 6464 VLED_MPCNC 7474 GND CN13
V21 8484 1_EMIT_INCAMERA VBUS 1 8 NC 9494 0_SPI_RDATAF
112N_BSU AREMACeludom CRFR YBDTS_DL 0505 0_SPI_LATF93P_BSU AREMAC2/x-a3 NO_DEL 1515 0_SPI_DATAF CN14014DNG AREMACnapaJ ylno LIAF 2525 0_SPI_CLKF
CAMERA GND 5 12 FER 3535 0_RESET_INMOLEX 501940-0507 1EPYT_LB 4545 0_EMIT_IN1-820-182-11 BL_TYPE2 5555 0_READY_O
BL_TYPE3 6565 GND
14pin connector
SPEAKER L+ (Fasten # 187) 1 1 +L11
YEONHO 20022WR-14AML
Front L- (Fasten #110) 2 2 2 -L2Lch 2 -R3
1 +R4+L51
3 -L6SPEAKER R- (Fasten # 110) 2 rotcennoC rekaepS gnisuoH3Front R+ (Fasten # 187) 1 4 2.1ch: 6pin 0-844-427-01 JST PBVP-06V 2.1ch: CN4602 6pin 0-844-174-01 JST SM06B-PBVSS-TB(LF)(SN)Rch
SPEAKER L+ 1 5ASSIST NC 2Lch L- 3 6
Refer to Sheet [ Appendix_SP_Connector ]
LED FFC30pin
LED FFC50pin
LED FFC30pin
LED FFC30pin
PANEL FFCSLCD : 68pin
SHARP : 80pinAUO : ??pin
CMI :32" 37" 60 pin40" 55" 80pin
LED FFC30pin
LED FFC30pin
LED FFC30pin
LED FFC30pin
LED FFC50pin
LED FFC50pin
LED FFC50pin
LED FFC50pin
LED FFC30pin
CN2001
FFC Direct in Connector :I-PEXLED FFC
30pin
LED FFC30pin
LED FFC30pin
LED FFC30pin
T-con Board(PEH2)
51pin FFC
LVDS-FFCB-PYL
LD - TC - HarnessTCON - LD
LD DirectBoard
BAT-L board
SSW module
RFRC module
BL- H HarnessH - B
LOGO module
HLT2 bosrd
CAMERA module
Wifi module(WW)
65"Only
55"Only
STBY3.3V 1 1RS232_RXD 2 2RS232_TXD 3 3SIRCS_IN 4 4SIRCS_OUT 5 5GND 6 6CN101182018311
R3 or RU board
Wifi module(JP)
[2b-1 55,65 1/2]
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 91
DIAGRAMS
4-2-2. KDL-55HX920/923/925 (2/2)
(Only Interface between board and board)
V21182V21262
27 3 GND25 4 GND
JST(VA)1-842-566-11
1 1 12VV2122
3 3 GNDDNG44
LRTC_SLG55
1DNG
2LRTC_SLG66
2XT_DTRAU
LIAF_IME77
3XR_DTRAU
CN88
4TESER5V3.3+_YBTS
Molex
6MVT_EDOM
1-842-558-11
7XR_ATRAU8)2DM( CN9XR_CTRAU01XT_CTRAU11DNG
1 1 VLED_VCC
21XT_ATRAU
2 2 VLED_VCC
31XIRTAM_SCE
3 3 VLED_VCC
41V3.3+_YBTS
4 4 VLED_VCC
51MEP_EDOM
NC 5 5 NC
61XR_GOL_MEP
6 6 VLED_GND
71XT_GOL_MEP
7 7 VLED_GND
81DNG
8 8 VLED_GND
CN9004
9 9 VLED_GND
1-774-667-51
10 10 VLED_GND
TL-EX1 Connector,FFC/FPC 18P
11 11 LD_ERR
10 10 STBY_+3.3V
NC 12 12 NC
12 9 AUDIO+12.5V
13 13 GL_CTRL
14 8 AUDIO+12.5V
14 14 LED_ON
11 7 AUDIO+12.5V_GND13 6 AUDIO+12.5V_GND
15 5 REG+12.5V_GND17 4 REG+12.5V_GND
16 3 REG+12.5V18 2 REG+12.5V
NC 1 T-CON_VCC
CN60011-821-620-11
HEADER ASSEMBLY FOR PWB 10P
7 9 AC_OFF_DET
1 8 POWERON6 7 BL_ERR
NC 6 NCNC 5 NCNC 4 NC
11V21
8 3 TCON_ON
22V21rettimE D3
3 2 PFC_PWR
33DNGV-a3
9 1 GND
44DNG
CN6002
GLS_CTRL 5 5
1-842-559-11
GLS_CTRL2 6 6EMI_FAIL 7 7
88CN1-821-135-11
CN6101 SJM20-28WLB
G6BW To B board (100106)T-CON_Vcc12V 28 1GND 27 3
T-CON_VCC12V 26 2GND 25 4
T-CON_VCC_12V To B 24 NCGND 23 NC
BDR_ASU_12V 22 NCGND 21 NC
BDR_ASU_12V 20 NCGND 19 NCREG12V 18 2
GND 17 4REG12V 16 3
GND 15 5AU_12V 14 8AU_GND 13 6AU_12V 12 9AU_GND 11 7STBY3.3V 10 10GND 9 1T-CON_ON 8 3AC_OFF_DET 7 9BL_ERR 6 7NC 5 NCNC 4 NCPFC_ON 3 2NC 2 NCPOWERON 1 8
REG_12V 1 1 1 1 REG_12V VLED_VCC 1 1
GND 2 2 2 2 GND VLED_VCC 2 233CN 3 3 NC G7D VLED_VCC 3 3
BL_ERR 4 4 4 4 BL_ERR VLED_VCC 4 455CN 5 5 NC NC 5 566CN 6 6 NC VLED_GND 6 6
AC_OFF_DET 7 7 7 7 AC_OFF_DET VLED_GND 7 7CN6102 1-821-888-11 1-821-888-11 VLED_GND 8 8
JST L 7p JST L 7p CN6701 VLED_GND 9 9
VLED_GND 10 10PRI_VCC 1 1 1 1 PRI_VCC LD_ERR 11 11PRI_GND 2 2 2 2 PRI_GND NC 12 12
CN6502 1-817-207-11 1-817-207-11 CN6601 GL_CTRL 13 13JST JST LED_ON 14 14PFC_GND 1 1 1 1 PFC_GNDPFC_OUT 2 2 11-933-228-1TUO_CFP22
SFP79-02WLB JAM CN6600 JST XA 14P CN6700SFP79-02WLB JAM 1-822-908-11
CN6501 1-822-908-11
AC_INAC-N 1 1AC-L 2 2CN6001SFP79-02WLB JAM1-822-908-11
Energy_Saving_SWAC(N)-IN 1 1AC(L)-IN 2 2CN6003
SFP79-02WLB JAM1-822-908-11
Energy_Saving_SWAC(L)-OUT 1 1AC(N)-OUT 2 2CN6002
SFP79-02WLB JAM1-822-908-11
G7E
HEM2 Board
TC-EM HarnessPEL3-HEM2
G-B Harness
LD DirectBoard
BAT-L board
ES SW
B board
T-con
Option
B board
TL-EX1JIG board
AC pigtail
T-con
T-con Board(PEH2)
14pin connector
YEONHO 20022WR-14AML
[2b-1 55,65 2/2]
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 92
DIAGRAMS
4-3. CIRCUIT BOARDS LOCATION
KDL-46HX920/923/925
BATL Board
HLT2 BoardSwitch Unit
G5B Board
T-CON
KDL-55HX920/923/925
T-CON
G6B Board
G7D Board
Switch Unit
CAMERA MODULEHEM2 Board
WIRELESS LAN CARD
BATL Board
HLT2 BoardCAMERA MODULEHEM2 Board
WIRELESS LAN CARD
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 93
SEC 5. EXPLODED VIEWS
Items with no part number and no description are not stocked because they are seldom required for roution service. The construction parts of an assembled part are indicated with a collation number in the remark colum. Items marked " * " are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items
IMPORTANT: When replacing LCD Panel or Circuit Boards ensure that all Radiation Sheets and Insulation Sheets are in their
correct positions in the TV set.
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 94
5-1. KDL-46HX920/923/925
5-1-1. CHASSIS-1
EXPLODED VIEWS
1
2
3
5
6
7
10
11
1213
14
15
17
18
19
16
9
8
4
REF. No. PART No. DESCRIPTION REMARK
1 FX0019811 POWER SWITCH2 FX0035321 SWITCH UNIT3 FX0000511 POWER-SUPPLY CORD (WITH CONN.)
FX0004012 POWER-SUPPLY CORD (WITH CONN.) HX923(UK)4 FX0036701 BRACKET BOTTOM5 FX0093501 HEM2 MOUNT6 FX0020701 CAP, SEALING (CAMERA)7 FX0019511 CAMERA MODULE8 FX0037101 BRACKET, SP ASSY9 FX0035511 LOUDSPEAKER (3X15CM)
10 FX0012011 WIRELESS LAN CARDFX0023711 WIRELESS LAN CARD HX920(RU)
11 FX0012211 ANTENNA12 FX0019711 ANTENNA13 FX0036901 REAR COVER (46 DL) A14 FX0036801 COVER, ANT(L DL)15 FX0018001 SHEET, ANT(C EL)16 FX0002711 COVER, AC(M)17 FX0007801 STAND HEAD (ML9)18 FX0030211 NECK (L9)19 FX0035912 STAND, BASE S (L1)
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 95
5-1-2. CHASSIS-2
EXPLODED VIEWS
5-1. KDL-46HX920/923/925
51
52
5455
53 56
57
58
60
59 61
62
63
64
65
65
65
65
REF. No. PART No. DESCRIPTION REMARK
50 FX0008301 SHEET, INSULATION (G4)51 FX0035211 STATIC CONVERTER (TV)-G5B52 FX0021411 SPEAKER BOX ASSY53 A-1808-279-A P-MOD (FQLF460DT01)(SERVICE)54 FX0020631 TAPE, PWB (H)55 FX0096101 HLT2 MOUNT (BRAEP)56 FX0020501 SHEET (BAT-L METAL SIDE)57 FX0020401 SHEET (BAT-L METAL BOTTOM)58 FX0019231 BRACKET BOTTOM (BAT-L METAL) HX925(AEP)
FX0021321 BRACKET BOTTOM (BAT-L METAL)59 FX0096201 BATL COMPL (SERVICE) HX920(AEP,RU)
FX0096301 BATL COMPL (SERVICE) HX925(AEP)FX0096901 BATL COMPL (SERVICE) HX923(AEP,UK)FX0096801 BATL COMPL (SERVICE) HX920(I)
60 FX0019121 BRACKET SIDE (BAT-L METAL)61 FX0036101 FRAME, HT(46 ALY)62 FX0036301 FRAME, VL(46 ALY)63 FX0036201 FRAME, HB(46 ALY)64 FX0036501 FRAME, VR(46 ALY)65 FX0036601 JOINT, CORNER
50
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 96
5-2. KDL-55HX920/923/925
5-2-1. CHASSIS-1
EXPLODED VIEWS
1
2
3
5
6
7
10
11
1213
14
15
17
18
19
16
9
8
4
REF. No. PART No. DESCRIPTION REMARK
1 FX0019811 POWER SWITCH2 FX0035321 SWITCH UNIT3 FX0000511 POWER-SUPPLY CORD (WITH CONN.)
FX0004012 POWER-SUPPLY CORD (WITH CONN.) HX923(UK)4 FX0036701 BRACKET BOTTOM5 FX0093501 HEM2 MOUNT6 FX0020701 CAP, SEALING (CAMERA)7 FX0019511 CAMERA MODULE8 FX0037101 BRACKET, SP ASSY9 FX0035511 LOUDSPEAKER (3X15CM)
10 FX0012011 WIRELESS LAN CARDFX0023711 WIRELESS LAN CARD HX920(RU)
11 FX0012211 ANTENNA12 FX0019711 ANTENNA13 FX0038401 REAR COVER (55 DL) ASSY14 FX0036801 COVER, ANT(L DL)15 FX0018001 SHEET, ANT(C EL)16 FX0002711 COVER, AC(M)17 FX0007801 STAND HEAD (ML9)18 FX0023211 NECK (LL9)19 FX0037912 STAND, BASE S (LL1)
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 97
5-2-2. CHASSIS-2
EXPLODED VIEWS
5-2. KDL-55HX920/923/925
51
52
55
56
5457
58
59
61
60
62
63
64
65
66
66
66
66
53
REF. No. PART No. DESCRIPTION REMARK
49 FX0010501 SHEET, INSULATION (G7)50 FX0008301 SHEET, INSULATION (G4)51 FX0037411 STATIC CONVERTER (TV)-G6B52 FX0037311 STATIC CONVERTER (TV)-G7D53 FX0028711 SPEAKER BOX ASSY (9X5CM)54 A-1808-281-A P-MOD (FQLF550DT01)(SERVICE)55 FX0020631 TAPE, PWB (H)56 FX0096101 HLT2 MOUNT (BRAEP)57 FX0020501 SHEET (BAT-L METAL SIDE)58 FX0020401 SHEET (BAT-L METAL BOTTOM)59 FX0019231 BRACKET BOTTOM (BAT-L METAL) HX925(AEP)
FX0021321 BRACKET BOTTOM (BAT-L METAL)60 FX0096201 BATL COMPL (SERVICE) HX920(AEP,RU)
FX0096301 BATL COMPL (SERVICE) HX925(AEP)FX0096901 BATL COMPL (SERVICE) HX923(AEP,UK)FX0096801 BATL COMPL (SERVICE) HX920(I)
62 FX0019121 BRACKET SIDE (BAT-L METAL)62 FX0038001 FRAME, HT(55 ALY)63 FX0038201 FRAME, VL(55 ALY)64 FX0038101 FRAME, HB(55 ALY)65 FX0038301 FRAME, VR(55 ALY)66 FX0036601 JOINT, CORNER
50
49
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 98
EXPLODED VIEWS
5-3-1. MISCELLANEOUS
46 InchesFX0001191 BAG, SCREW ASSY (L) - (See note on page 100)FX0005901 CLAMPER CABLE - (Not shown)FX0020221 CONNECTOR ASSY - (CN6002(G5)CN6003(G5)-ECOSW(1))
* FX0035617 CONNECTOR ASSY 14P - (CN6801(G5B)-CN2001(LD)(1))* FX0035720 CONNECTOR ASSY 28P - (CN6001(BATL)-CN6002(BATL)-CN6151(G5B)-TCON(1))
FX0035411 FLEXIBLE FLAT CABLE Y1 46S - (CN2001(BATL)-PANEL(1))* FX0035868 HARNESS ASSY - (CN9006(BATL)-CN001(HLT2)-HEM2-LOGO-WIFI-CAMERA-SW/CN4601(BATL)SP(1))
FX0021101 LABEL (BATL METAL BOTTOM) - (Not shown)FX0021811 LABEL (BATL METAL BOTTOM) - (Not shown) - (HX925)FX0021001 LABEL (BATL METAL SIDE) - (Not shown)FX0001401 SHEET (CORE) C - (Not shown)FX0002001 SHEET RADIATION (BAT-L/V) - (Not shown)FX0035001 SHEET ALUMINIUM - (Not shown)FX0010302 SPACER (GA) - (Not shown)FX0002402 SPACER (GB) - (Not shown)FX0037293 TAPE, ADHESIVE(UT2340) 10X20MM - (Not shown)
5-3. OTHER PARTS
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 99
EXPLODED VIEWS
55 InchesFX0001191 BAG, SCREW ASSY (L) - (See note on page 100)FX0005901 CLAMPER CABLE - (Not shown)FX0024121 CONNECTOR ASSY - (CN6003(G6)CN6002(G6)-ECOSW(1))
* FX0037628 CONNECTOR ASSY 14P - (CN6700(G7)-CN2001(LD)(1))* FX0037731 CONNECTOR ASSY 28P - (CN6101(G6)-CN6001(BATL)-CN6002(BATL)-CN8003(TCON(1))
FX0010921 CONNECTOR ASSY 2P- (CN6502(G6)CN6601(G7/G8)(1))FX0011021 CONNECTOR ASSY 2P- (CN6501(G6)CN6600(G7/G8)(1))
* FX0011545 CONNECTOR ASSY 7P- (CN6102(G6)-CN6701(G7/G8)(1))FX0037511 FLEXIBLE FLAT CABLE - (CN2001(BATL)-PANEL(1))
* FX0037876 HARNESS ASSY - (CN9006(BATL)-CN001(HLT2)-HEM2-LOGO-WIFI-CAMERA-SW/CN4601(BATL)SP(1))FX0021101 LABEL (BATL METAL BOTTOM) - (Not shown)FX0021811 LABEL (BATL METAL BOTTOM) - (Not shown) - (HX925)FX0021001 LABEL (BATL METAL SIDE) - (Not shown)FX0001401 SHEET (CORE) C - (Not shown)FX0002001 SHEET RADIATION (BAT-L/V) - (Not shown)FX0010302 SPACER (GA) - (Not shown)
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 100
EXPLODED VIEWS
5-3-2. ACCESSORIES
FX0018411 3D EYEWEARFX0019911 CABLE CONVERSIONFX0020011 CABLE CONVERSIONFX0035111 CAMERA AND MICROPHONE UNIT
* FX0021723 MANUAL, INSTRUCTION - HX920(AEP)* FX0021973 MANUAL, INSTRUCTION - HX925(AEP)* FX0022033 MANUAL, INSTRUCTION - HX920,923(AEP)* FX0022353 MANUAL, INSTRUCTION - HX920(IT)* FX0022413 MANUAL, INSTRUCTION - HX923(UK)* FX0024443 MANUAL, INSTRUCTION - HX920(RU)
FX0012111 REMOTE COMMANDER (RM-ED041)FX0018611 USB CABLE
NoteThe "Bag , Screw Assy" contains the following:-Screw, +PSW M5x16Hex WrenchUser Screw ST
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 101
END
9-888-423-01
Sony CorporationSony UK
Service Promotions Dept.
English11DP7100-1Made in U.K.
2011. 04
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 102
PROCEDURE TO REMOVE THE REAR COVER
AC Cable2 34 AC Cover
APPENDIX-1
1. Remove the screws from the REAR COVER and the COVER AC.
2. Open the REAR COVER with the COVER AC and AC cable attached.
Note: Make sure to hold the cable not to give any tension to the connector and scratch damage for the cable.
3. Release the AC cable connector.
4. Release the hooks of the COVER AC and remove it.
Note:Take care not to cut your hands when releasing the hooks, especially on the metal RC.Confirm the hooks are not broken before re-using the COVER AC.If the hooks are broken please replace with a new one.
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 103
OK to grab(curling area)
OK to grab with care(sharp edge area)
NG to grab(sharp edge and easy to deform.)
APPENDIX-2
CAUTION FOR THE SHARP EDGES OF THE REAR COVER(46)
-
KDL-46/55HX920,923,925(AEP/UK/RUSS) 104
OK to grab(curling area)
OK to grab with care(sharp edge area)
NG to grab(sharp edge and easy to deform.)
APPENDIX-2
CAUTION FOR THE SHARP EDGES OF THE REAR COVER(55)
HISTORY INFORMATIONFRONT COVERMODEL LISTWARNINGS AND CAUTIONSUSE CAUTION WHEN HANDLING THE LCD PANELHANDLING THE TENGO PANELHANDLING THE FFCSAFETY CHECK-OUTSELF DIAGNOSIS FUNCTIONSEC 1. DISASSEMBLY1-1. KDL-46HX920/923/9251-1-1. STAND BLOCK, HEAD STAND, NECK AND BASE STAND1-1-2. REAR COVER, AC COVER, ANT COVER AND ANT SHEET1-1-3. SWITCH UNIT AND POWER SWITCH1-1-4. HARNESS1-1-5. POWER SUPPLY CORD AND G5B BOARD1-1-6. WIRELESS LAN CARD1-1-7. ANTENNA1-1-8. SPEAKER BOX ASSY1-1-9. SPEAKER BOX ASSY (WOOFER)1-1-10. BOTTOM BRACKET1-1-11. SIDE BRACKET AND BATL BOARD1-1-12. SHEET1-1-13. CAMERA MODULE AND SEALING CAP(CAMERA)1-1-14. HEM2 BOARD1-1-15. BOTTOM BRACKET AND SP BRACKET1-1-16. FRAME AND JOINT CORNER1-1-17. HLT2 BOARD, PWB (H) TAPE AND PANEL MODULE
1-2. KDL-55HX920/923/9251-2-1. STAND BLOCK, HEAD STAND, NECK AND BASE STAND1-2-2. REAR COVER, AC COVER, ANT COVER AND ANT SHEET1-2-3. SWITCH UNIT AND POWER SWITCH1-2-4. HARNESS-11-2-5. HARNESS-21-2-6. G7D BOARD1-2-7. POWER SUPPLY CORD AND G6B BOARD1-2-8. WIRELESS LAN CARD1-2-9. ANTENNA1-2-10. SPEAKER BOX ASSY1-2-11. SPEAKER BOX ASSY (WOOFER)1-2-12. BOTTOM BRACKET1-2-13. SIDE BRACKET AND BATL BOARD1-2-14. SHEET1-2-15. CAMERA MODULE AND SEALING CAP(CAMERA)1-2-16. HEM2 BOARD1-2-17. BOTTOM BRACKET AND SP BRACKET1-2-18. FRAME AND JOINT CORNER1-2-19. HLT2 BOARD, PWB (H) TAPE AND PANEL MODULE
SEC 2. ADJUSTMENTHOW TO ENTERING SERVICE MODEWHITE BALANCE ADJUSTMENTRESTORE WHITE BALANCE / GAMMA ADJ-DATA TO B BOARDSAVE CHANGING DATACHANGE DATASET TO SHIPPING CONDITIONCHANGE THE EMITTER OUTPUT LEVELHDD REC SETTING
SEC 3. TROUBLE SHOOTING3-1. TRIAGE CHART3-2. FLOW CHART3-3. NO POWER3-4. STANDBY LED BLINK1) 2 times blinking (Main Power Error)2) 3 times blinking (DC Alert, Audio Error and Communication Error)3) 4 times blinking (Including SPI Error)4) 5 times blinking (T-con Error)5) 6 times blinking (Backlight Error)6) 7 times blinking (Temperature Error)7) 8 times blinking (Software Error)8) 10 times blinking (Emitter Error)
3-5. NO PICTURE3-6. NO SOUND3-7. TV COMMANDER BUTTONS MALFUNCTION1) TV button malfunction2) IR remote commander malfunction
3-8. NETWORK MALFUNCTION1) Wired Network malfunction2) USB Wireless Network malfunction3) Internal Wireless Network malfunction
3-9. CAMERA MALFUNCTION3-10. 3D MALFUNCTION3-11. Skype MALFUNCTION 1/23-11. Skype MALFUNCTION 2/23-12. HDD-Rec MALFUNCTION
SEC 4. DIAGRAMS4-1. BLOCK DIAGRAM4-2. CONNECTOR DIAGRAM4-2-1. KDL-46HX920/923/925 (1/2)4-2-1. KDL-46HX920/923/925 (2/2)4-2-2. KDL-55HX920/923/925 (1/2)4-2-2. KDL-55HX920/923/925 (2/2)
4-3. CIRCUIT BOARDS LOCATION
SEC 5. EXPLODED VIEWS5-1. KDL-46HX920/923/9255-1-1. CHASSIS-15-1-2. CHASSIS-2
5-2. KDL-55HX920/923/9255-2-1. CHASSIS-15-2-2. CHASSIS-2
5-3. OTHER PARTS5-3-1. MISCELLANEOUS5-3-2. ACCESSORIES
BACK COVERAPPENDIX-1APPENDIX-2
/ColorImageDict > /JPEG2000ColorACSImageDict > /JPEG2000ColorImageDict > /AntiAliasGrayImages false /CropGrayImages true /GrayImageMinResolution 300 /GrayImageMinResolutionPolicy /OK /DownsampleGrayImages true /GrayImageDownsampleType /Bicubic /GrayImageResolution 300 /GrayImageDepth -1 /GrayImageMinDownsampleDepth 2 /GrayImageDownsampleThreshold 1.50000 /EncodeGrayImages true /GrayImageFilter /DCTEncode /AutoFilterGrayImages true /GrayImageAutoFilterStrategy /JPEG /GrayACSImageDict > /GrayImageDict > /JPEG2000GrayACSImageDict > /JPEG2000GrayImageDict > /AntiAliasMonoImages false /CropMonoImages true /MonoImageMinResolution 1200 /MonoImageMinResolutionPolicy /OK /DownsampleMonoImages true /MonoImageDownsampleType /Bicubic /MonoImageResolution 1200 /MonoImageDepth -1 /MonoImageDownsampleThreshold 1.50000 /EncodeMonoImages true /MonoImageFilter /CCITTFaxEncode /MonoImageDict > /AllowPSXObjects false /CheckCompliance [ /None ] /PDFX1aCheck false /PDFX3Check false /PDFXCompliantPDFOnly false /PDFXNoTrimBoxError true /PDFXTrimBoxToMediaBoxOffset [ 0.00000 0.00000 0.00000 0.00000 ] /PDFXSetBleedBoxToMediaBox true /PDFXBleedBoxToTrimBoxOffset [ 0.00000 0.00000 0.00000 0.00000 ] /PDFXOutputIntentProfile () /PDFXOutputConditionIdentifier () /PDFXOutputCondition () /PDFXRegistryName () /PDFXTrapped /False
/Description > /Namespace [ (Adobe) (Common) (1.0) ] /OtherNamespaces [ > /FormElements false /GenerateStructure false /IncludeBookmarks false /IncludeHyperlinks false /IncludeInteractive false /IncludeLayers false /IncludeProfiles false /MultimediaHandling /UseObjectSettings /Namespace [ (Adobe) (CreativeSuite) (2.0) ] /PDFXOutputIntentProfileSelector /DocumentCMYK /PreserveEditing true /UntaggedCMYKHandling /LeaveUntagged /UntaggedRGBHandling /UseDocumentProfile /UseDocumentBleed false >> ]>> setdistillerparams> setpagedevice