solar module installation manualfigure 6 130w solar module bracket assembly figure 7 130w solar...

Solar ModuleInstallation Manual

1

Online ResourcesUse this QR code or visit www.truelook.com/install to access:

1. An admin guide to walk you through creating your time-lapses and other administrative settings.

2. Video demonstrations of installation procedures.

3. A digital PDF of this install guide.

4. Download links for the TrueLook mobile app.

5. Other help resources.

Disclaimer: There are no installation services provided by TrueLook for this equipment. Neither TrueLook nor any of its

a� liates shall be held responsible or liable in any manner for the improper installation or operation of any software or

hardware installed by any party not authorized by TrueLook as a certifi ed installer. Furthermore, customer agrees to hold

harmless TrueLook and any of its a� liates from any and all liability and/or responsibility for any violation of local, state,

or federal laws or regulations pertaining to the installation and/or operation of any of the hardware and/or software

provided by TrueLook and its a� liates.

The information contained in this document represents TrueLook’s current product as of the date of publication and is

subject to change without notice. TrueLook cannot guarantee the accuracy of any information presented. Product and

company names mentioned herein may be the trademarks of their respective owners.

2

FIGURE 1 Battery Enclosure MountingSecure the enclosure to the pole or other structure.

BEFORE BEGINNING THE SOLAR MODULE INSTALLATION, PLEASE COMPLETE THE FULL HARDWARE INSTALLATION PROCESS, DETAILED IN ACCOMPANYING ‘CAMERA INSTALLATION MANUAL.’!

3

FIGURE 2 Single Battery Installation

1. Snap the Positive (red) battery cable to the Positive (red) connector on the battery using the supplied hardware.

2. Repeat for Negative cable (black).

ALL BREAKERS, LOCATED IN THE UPPER RIGHT OF THE BATTERY ENCLOSURE, MUST BE SET TO “OFF” BEFORE CONTINUING.!

FIGURE 2 Single Battery Installation

4

1 2

Fig. 2

5

FIGURE 4 90W Solar Module Bracket Assembly

FIGURE 5 90W Solar Module Bracket Mounting

1. Using the supplied 5/16” hardware, attach the 90˚foot brackets to the aluminum channel.

2. Install the solar brackets to the feet also using the 5/16” hardware.

3. Install the solar panel to the solar brackets using the supplied 1/4” hardware.

4. Secure the channel to desired structure.

6



1 1

2 2

3

3

4

Fig. 4

Fig. 5

7



1. Using the supplied 5/16” hardware, install 2 foot brackets to the 1st aluminum channel.

2. Repeat process for the 2nd channel.

3. Attach the solar brackets to the 1st channel.

4. Attach the wind braces to the 2nd channel.

5. Attach the wind braces to the solar brackets.

6. Install the solar panel to the solar brackets using the supplied 1/4” hardware.

7. Secure the channel to desired structure

8



1

2

3

6

6

6

7

4

5

Fig. 6 Fig. 7

9

FIGURE 8 Optional Pipe Skid Assembly

FIGURE 9 Pipe Skid Ballasts Placement

1. Insert the long horizontal pipe all the way through the base tee. Use a hex key to secure the bolt under the tee.

2. Place the 2 small horizontal pipes followed by the vertical pipe. Secure all the bolts.

1. Place the ballasts (not provided) on the ends of the horizontal pipe

10

FIGURE 8 Optional Pipe Skid Assembly

FIGURE 9 Pipe Skid Ballasts Placement

Fig. 8

Fig. 9

22

222 2

11

11

FIGURE 10 Positioning Solar Panel 1. Install solar modules with panel face positoned toward the equator.

2. Adjust angle of panel based o� geo-location, see chart at right.

80°65°

45°

EQUATOR

PANELFACE

Fig. 10

SU

PP

OR

T S

TR

UC

TU

RE

12

FIGURE 10 Positioning Solar Panel Alabama 45°

Alaska 80°

Arizona 45°

Arkansas 60°

California 45°

Colorado 55°

Connecticut 60°

Delaware 65°

District of Col. 60°

Florida 45°

Georgia 55°

Hawaii 40°

Idaho 65°

Illinois 65°

Indiana 65°

Iowa 65°

Kansas 65°

Kentucky 60°

Louisiana 45°

Maine 65°

Maryland 60°

Massachusetts 65°

Michigan 65°

Minnesota 65°

Mississippi 45°

Missouri 60°

Montana 70°

Nebraska 65°

Nevada 65°

New Hampshire 65°

New Jersey 65°

New Mexico 45°

New York 65°

North Carolina 60°

North Dakota 70°

Ohio 60°

Oklahoma 50°

Oregon 65°

Pennsylvania 65°

Rhode Island 65°

South Carolina 55°

South Dakota 65°

Tennessee 60°

Texas 45°

Utah 65°

Vermont 65°

Virginia 60°

Washington 65°

West Virginia 60°

Wisconsin 65°

Wyoming 65°

13

FIGURE 11 Connecting Solar Module and Camera1. Connect the Solar Module and Camera to the appropriate male and female connectors

(A) located on the bottom of the Battery Enclosure. The connectors are positive locking

mechanisms and each pair is keyed di� erently to ensure that they are connected properly.

14

FIGURE 11 Connecting Solar Module and CameraFig. 11

A

15

FIGURE 12 Commissioning System

Locate Breakers in the upper right of the Battery Enclosure

1. Turn Battery breaker ON. The Prostar unit will power on and boot up.

2. Turn Solar breaker ON. With sunlight, the leftmost LED will turn green within 2 minutes. It is important to verify the panel is charging the unit.

3. Turn Load (Camera) Breaker ON.

4. Verify that the following numbers are displayed on the Prostar’s digital readout. You may need to cycle left/right using the arrows to get to the pictured screen.

A. Solar Amps = 0.5 - 4+ B. Battery = 12-14+ C. Load Amps = 0.3 - 0.7.

5. If numbers are displayed correctly, the system should be fully functioning at this stage.

TO PREVENT DAMAGE TO THE SYSTEM, BATTERY BREAKER MUST BE SET TO “ON” BEFORE CONTINUING TO STEP 2.!

16

FIGURE 12 Commissioning System

Fig. 12

1 2 3 4

17

TROUBLESHOOTINGIf something seems wrong with the system (for example, the load is not working or the

battery is not charging), then it may be necessary to troubleshoot the controller. Some

basic troubleshooting procedures are listed below.

CAUTIONS:

• Troubleshooting should be attempted by qualifi ed personnel only.

• Remember that a battery can cause serious damage if shorted.

• Do not disassemble the ProStar from its case. There are no user serviceable parts inside the ProStar.

• Observe all normal precautions.

BATTERY IS NOT CHARGING:

1. Check for proper LED indications on the ProStar. The (green) CHARGING LED should be on if it is daytime. One of the BATTERY CHARGE LED’s should be on. Check for proper battery voltage and array current.

2. Check that the proper BATTERY TYPE has been selected. Correct type is SEALED.

3. Check that all wire connections in the system are correct and tight.

18

TROUBLESHOOTING TROUBLESHOOTING ContinuedCAMERA NOT OPERATING PROPERLY:

1. Check that the load breaker is turned on.

2. Check that the camera cable connectors are securely fastened to each other.

3. Check for proper LED indications on the ProStar. If the (red) BATTERY CHARGE LED is on, the load has been disconnected due to low battery voltage. This is generally a normal state when the load exceeds the output due to weather and sunlight conditions.

4. If all LED indicators are fl ashing in sequence, the load may be shorted. For this scenario, contact technical support.

5. If the ProStar internal temperature is above 80°C/176°F, the load will be disconnected. All LED’s will be fl ashing in sequence. Check to ensure for clear airfl ow around the ProStar and that nothing is obstructing the vents at the top of the case.

solar module installation manualfigure 6 130w solar module bracket assembly figure 7 130w solar...

Documents