software defined radio_basics and evolution of cognitive radio

7/31/2019 Software Defined Radio_basics and Evolution of Cognitive Radio

1/21

EURASIP Journal on Wireless Communications and Networking 2005:3, 275283c 2005 Friedrich K. Jondral

Software-Dened RadioBasics and Evolutionto Cognitive Radio

Friedrich K. JondralUniversitat Karlsruhe (TH), Institut f ur Nachrichtentechnik, D-76128 Karlsruhe, Germany Email: [email protected]

Received 24 February 2005; Revised 4 April 2005

We provide a brief overview over the development of software-dened or recongurable radio systems. The need for software-dened radios is underlined and the most important notions used for such recongurable transceivers are thoroughly dened.The role of standards in radio development is emphasized and the usage of transmission mode parameters in the constructionof software-dened radios is described. The software communications architecture is introduced as an example for a framework that allows an object-oriented development of software-dened radios. Cognitive radios are introduced as the next step in radiosystems evolution. The need for cognitive radios is exemplied by a comparison of present and advanced spectrum managementstrategies.

Keywords and phrases: software-dened radio, recongurable transceiver, mobile communication standards, cognitive radio,advanced spectrum management.

1. INTRODUCTIONRecongurability in radio development is not such a new technique as one might think. Already during the 1980s re-congurable receivers were developed for radio intelligencein the short wave range. These receivers included interestingfeatures like automatic recognition of the modulation modeof a received signal or bit stream analysis. Recongurability became familiar to many radio developers with the publica-tion of the special issue on software radios of the IEEE Com-munication Magazine in April 1995.

We refer to a transceiver as a software radio (SR) if itscommunication functions are realized as programs runningon a suitable processor. Based on the same hardware, di ff er-ent transmitter/receiver algorithms, which usually describetransmission standards, are implemented in software. An SR transceiver comprises all the layers of a communication sys-tem. The discussion in this paper, however, mainly concernsthe physical layer (PHY).

The baseband signal processing of a digital radio (DR) isinvariably implemented on a digital processor. An ideal SR directly samples the antenna output. A software-dened ra-dio (SDR) is a practical version of an SR: the received signalsare sampled after a suitable band selection lter. One remark

This is an open access article distributed under the Creative CommonsAttribution License, which permits unrestricted use, distribution, andreproduction in any medium, provided the original work is properly cited.

concerning the relation between SRsandSDRs is necessary atthis point: it is often argued that an SDR is a presently realiz-able version of an SR since state-of-the-art analog-to-digital(A/D) converters that can be employed in SRs are not avail-able today. This argument, although it is correct, may lead tothe completely wrong conclusion that an SR which directly digitizes the antenna output should be a major goal of futuredevelopments. Fact is that the digitization of an unnecessary huge bandwidth lled with many di ff erent signals of whichonly a small part is determined for reception is neither tech-nologicallynor commercially desirable. 1 However, there is noreason for a receiver to extremely oversample the desired sig-nals while respecting extraordinary dynamic range require-ments for the undesired in-band signals at the same time.Furthermore, the largest portion of the generated digital in-formation, which stems from all undesired in-band signals,is ltered out in the rst digital signal processing step.

A cognitive radio (CR) is an SDR that additionally sensesits environment, tracks changes, and reacts upon its ndings.A CR is an autonomous unit in a communications environ-ment that frequently exchanges information with the net-works it is able to access as well as with other CRs. From ourpoint of view, a CR is a rened SDR while this again repre-sents a rened DR.

1This is not an argument against the employment of multichannel orwideband receivers.
mailto:[email protected]:[email protected]


2/21

276 EURASIP Journal on Wireless Communications and Networking

R e c e i v e

T r a n s m

i t

Radiofrequency

(RF)

Analog-to-digitalconversion

(A/D)

Basebandprocessing

Dataprocessing

Control(parameterization)

Radio front end

T o u s e r

F r o m u s e r

Figure 1: SDR transceiver.

According to its operational area an SDR can be

(i) a multiband system which is supporting more than onefrequency band used by a wireless standard (e.g., GSM900, GSM 1800, GSM 1900),

(ii) a multistandard system that is supporting more thanone standard. Multistandard systems can work withinone standard family (e.g., UTRA-FDD, UTRA-TDDfor UMTS) or across diff erent networks (e.g., DECT,GSM, UMTS, WLAN),

(iii) a multiservice systemwhich provides di ff erent services(e.g., telephony, data, video streaming),

(iv) a multichannel system that supports two or more in-dependent transmission and reception channels at thesame time.

Ourpresent discussion is on multimodesystems which arecombinations of multiband and multistandard systems.

The SDR approach allows diff erent levels of recongura-tion within a transceiver.

(i) Commissioning : the conguration of the system isdone once at the time of product shipping, when thecostumer has asked for a dedicated mode (standard orband). This is not a true reconguration.

(ii) Reconguration with downtime: reconguration is only done a few times during product lifetime, for example,when the network infrastructure changes. The recon-guration will take some time, where the transceiver isswitched off . This may include the exchange of com-ponents.

(iii) Reconguration on a per call basis: reconguration isa highly dynamic process that works on a per call de-cision. That means no downtime is acceptable. Only parts of the whole system (e.g., front-end, digital base-band processing) can be rebooted.

(iv) Reconguration per timeslot : reconguration can evenbe done during a call.

Figure 1 shows an SDR transceiver that di ff ers from aconventional transceiver only by the fact that it can be recon-gured via a control bus supplying the processing units withthe parameters which describe the desired standard. Sucha conguration, called a parameter-controlled (PaC) SDR,guarantees that the transmission can be changed instanta-neously if necessary (e.g., for interstandard handover).

The rest of this paper is organized as follows. In Section 2we take a look at the most important wireless transmis-sion standards currently used in Europe and specify theirmain parameters. Section 3 provides an overview of designapproaches for mobile SDR terminals, especially over PaC-SDRs. In Section 4 the software communications architec-

ture (SCA), as it is used in the US Joint Tactical Radio System(JTRS), is introduced. The notion of cognitive radio (CR)is discussed in Section 5 and the need for a modied spec-trum management in at least some major portions of theelectromagnetic spectrum is underlined in Section 6. Finally,in Section 7 we propose the development of technology cen-tric CRs as a rst step towards terminals that may sense theirenvironment and react upon their ndings. Conclusions aredrawn in Section 8.

2. MOBILE COMMUNICATION STANDARDS

Standards are used to publicly establish transmission meth-ods that serve specic applications employable for mass mar-kets. The presently most important mobile communicationstandards used in Europe are briey described in the follow-ing paragraphs.

Personal area networksBluetooth is a short distance network connecting portabledevices, for example, it enables links between computers,mobile phones or connectivity to the internet.

Cordless phoneDECT (digital enhanced cordless telecommunications) pro-vides a cordless connection of handsets to the xed telephonesystem for in-house applications. Its channel access mode isFDMA/TDMA and it uses TDD. The modulation mode of DECT is Gaussian minimum shift keying (GMSK) with abandwidth (B) time (T) product of BT = 0.5. The transmis-sion is protected only by a cyclic redundancy check (CRC).

Wireless local area networksToday, IEEE 802.11b installations are the most widely usedin Europe. Also, IEEE 802.11a systems are in operation. If IEEE.11a is to be implemented into an SDR, it should berecognized that its modulation mode is OFDM. It shouldbe pointed out here that there are major e ff orts towards thedevelopment of joint UMTS/WLAN systems which use theSDR approach.

Cellular systemsGSM (global system for mobile communication) is presently the most successful mobile communication standard world-wide. Channel access is done via FDMA/TDMA and GSMuses FDD/TDD. The modulation mode of GSM is GMSKwith a bandwidth time product of BT = 0.3. Error correctioncoding is done by applying CRC as well as a convolutionalcode. GSM was originally planned to be a voice communi-cation system, but with its enhancements HSCSD, GPRS, orEDGE, it served more and more as a data system, too. In Eu-rope, GSM systems are operating in the 900 MHz (GSM 900)


3/21

SDRBasics and Evolution to Cognitive Radio 277

800 900 1000 1100 1200 1300 1400 1500 1600

8 9 0

9 1 5

9 3 5

9 6 0

1600 1700 1800 1900 2000 2100 2200 2300 2400 2500

1 7 1 0

1 7 8 5

1 8 0 5

1 8 8 0

1 9 2 0

1 9 8 0

2 0 1 0

2 0 2 5

2 1 1 0

2 1 7 0

2 4 8 3 . 5

5100 5200 5300 5400 5500 5600 5700 5800 5900

5 1 5 0

5 3 5 0

5 4 7 0

5 7 2 5

GSM

DECT

UTRA-TDD

UTRA-FDD

MSS

ISM

WLAN

f (MHz)

Figure 2: Mobile spectrum in Europe.

as well as in the 1800 MHz (GSM 1800) bands. The NorthAmerican equivalent of GSM is IS-136. Also, GSM 1900 aswell as IS-95, a second-generation CDMA system, are widely used in the US. UMTS (universal mobile telecommunicationsystem) is the European version of the third-generation fam-ily of standards within IMT-2000. One of the di ff erences withrespect to second-generation systems is that third-generationsystems are mainly developed for data (multimedia) trans-

mission. UMTS applies two air interfaces: UTRA-FDD andUTRA-TDD according to the duplex modes used. The chan-nel access mode is CDMA. CRC, convolutional codes, as wellas turbo codes [ 1] are employed for error protection. Thebasic data modulation is QPSK. Furthermore, it should bementioned that one mobile user within an UTRA-FDD cellcan occupy up to seven channels (one control and six trans-port channels) simultaneously.

Figure 2 gives an overview over the present spectrum al-location for mobile communications in Europe. Besides thespectra of the standards mentioned above, also the spectraallocated to mobile satellite system (MSS) as well as to indus-trial, scientic, and medical (ISM) applications are specied.

Thearrows within some of thebands indicate whether uplink (mobile to base station) or downlink (base station to mobile)traffi c is supported.

In connection with mobile communications, some addi-tional groups of standards have to be discussed.

Professional mobile radioPMR standards are developed for police, reghters, andother administrative applications. Themain di ff erence to cel-lular systems is that they allow direct handheld to hand-held communication. The main PMR systems in Europe areTETRA (recommended by ETSI) and TETRAPOL.

Location and navigationOne important feature of mobile terminals is their ability todetermine their own location as well as to track location in-formation. Today many location-dependent services rely onthe global positioning system (GPS). Currently the Europeansatellite location and navigation system Galileo is under de-velopment.

Digital broadcast There is a possibility that digital broadcast systems may beused as downstreaming media within future mobile commu-nication infrastructures. The main developments in Europein this area are digital audio broadcast (DAB) and digitalvideo broadcast (DVB).

To have a sound basis for the description of a PaC-SDR that can be switched between di ff erent standards, the mostimportant parameters of selected air interfaces are summa-rized in Table 1.

3. MOBILE SDR TERMINALS

The general structure of a PaC-SDR terminal was already given in Figure 1. Nowweare going to look into the PaC-SDR transceiver structure in a more detailed way. The main pro-cessing modules of an SDR terminal are the radio front-end,the baseband processing, and the data processing. Since a lotof information about baseband processing can be found inthe literature [ 2, 3] and since data processing is out of thescope of this paper, we are going to focus on the front-endhere.

The receiver branch transforms the analog RF antennasignal into its digital complex baseband representation.


4/21


Table 1: Parameters of selected air interfaces.

Bluetooth DECT GSM UTRA-FDD

Frequency range 2 .4 GHz (ISM band) 1900 MHz 900, 1800, 1900 MHz 2 GHzChannel bandwidth 1 MHz 1728 kHz 200 kHz 5 MHz

Access mode TDMA FDMA/TDMA FDMA/TDMA Direct sequence (DS)CDMA

Duplex mode TDD TDD FDD FDDUsers per carrier frequency 8 maximum 12 8

ModulationFH sync. to master station,

GMSK GMSK QPSKGFSK with modulationindex between 0 .28 and 0.35

Error correction code No (CRC) CRC, convolutional CRC, convolutional, turboBit (chip) rate 1 Mbps 1152 kbps 270 .833 kbps 3.840Mchip/sNumber of bits (chips)/burst(slot) 625 480 (DECT P32) 156.25 2560

Frame duration 10 ms 4 .615 ms 10 msNumber of bursts(slots)/frame

24 8 15

Burs t (slot) duration 0 .625 ms 0.417 ms 0.577 ms 0.667msMaximum cell radius 510 m (1 mW Tx power) 300 m 36 km (10 km) Few km

Spreading sequences User specic OVSF codes,call specic scrambling

Spreading factor 2k (k = 2,3, . . . , 8), 512

for downlink only Bit (chip) pulse shaping

Gauss (BT = 0.5) Gauss (BT = 0.5) Gauss (BT = 0.3)Root-raised cosine,

lter roll-off factor 0.22Net data rate 1 Mbps 26 kbps 13 kbps 8 kbps to 2 MbpsEvolutionary concepts UWB GPRS, HSCSD, EDGE HSDPAComparable systems PHS, PACS, WACS IS-136, PDC UMTS-TDD. Cdma2000

TETRA IEEE 802.11a GPS DVB-T

Frequency range 400 MHz 5 .5 GHz 1200, 1500 MHz VHF, UHFChannel bandwidth 25 kHz 20 MHz 7 (VHF) or 8 MHz (UHF)

Access mode TDMA FDMA/TDMADirect sequence spreadspectrum FDMA

Duplex mode FDD/TDD Half duplex Users/carrier

4 frequency

Modulation / 4-DQPSKOFDM with subcarrier

BPSK, QPSKOFDM with subcarrier

modulation modulationBPSK/QPSK/16QAM/64QAM QPSK/16QAM/64QAM

Error correction code CRC, Reed-Muller, RCPC Convolutional Reed-Solomon, convolutional

Bit (chip) rate 36 kbps 6/9/12/18/24/36/48/54 Mbps 50 bps 9.143 Msamples/s for an8 MHz channel

Number of bits (chips) 510 (255 symbols) 52 modulated symbols per 2k mode: 2048 + guard int.per burst (slot) OFDM symbol 8k mode: 8192 + guard int.Frame duration 56 .67 ms Packets of several 100s 15 s (7500 bit) 68 OFDM symbolsNumber of bursts

4 Variable 5 subframes 68(slots) per frame

Burst (slot) duration 14.167ms1 OFDM symbol of 3.3 s +

30 s2k mode: 224 s + guard time

0.8 s guard time 8k mode: 896 s + guard timeMaximum cell radius Some 10 m Spreading sequences Gold or PRN code Spreading factor 1023 or 10 230 Bit (chip) pulse Root-raised cosine, Rectangular, other lteringshaping lter roll-o ff factor 0.35 possibleNet data rate Up to 28 .8 kbps Up to 25 Mbps 49 .8131.67MbpsEvolutionary concepts IEEE 802.11n Galileo Comparable systems TETRAPOL HiperLAN/2 GLONASS DAB


5/21


RF

RF

2

A/D

A/D

I / Q b a l a n c i n g

S a m p

l i n g r a t e a d a p t a t i o n Inphase

component

Quadraturecomponent

Parameter control

Figure 3: SDR/CR receiver front-end.

Figure 3 shows how it works: coming from the antenna, theRF signal is rst bandpass ltered and then amplied. Fol-lowing a two-way signal splitter, the next step is an analogmixing with the locally generated RF frequency in the in-phase (I) path and with the same frequency phase shifted by / 2 in the quadrature (Q) path. Afterwards, the I and Qcomponents of the signal are lowpass ltered and A/D con-verted. The sampling rate of the A/D converters should bexedfor all signals and has tobe chosenin sucha way thattheconditions of Shannons sampling theorem are fullled forthe broadest signal to be processed. Before the sampling ratecan be adapted to the signals standard, the impairments of the two-branch signal processing that come from the analogmixers and lters as well as from the A/D converters them-selves have to be corrected [4].

The reason for the Sampling rate adaptation is that thesignal processor should work at the minimum possible rate.For a given standard, this minimum sampling rate dependson f c = 1 /T c, the symbol or chip rate, respectively. Usually asampling rate of f s = 4 f c is suffi cient for the subsequent sig-nal processing where, after the precise synchronization, thesampling rate may be reduced once more by a factor of 4.If the fraction of the sampling rates at the adaptors outputand input is rational (or may be su fficiently close approxi-mated by a rational number), the sampling rate adaptationcan be implemented by an increasing of the sampling ratefollowed by an interpolation lowpass lter and a decreasingof the sampling rate. If the interpolation lowpass is imple-mented by an FIR lter, the impulse response usually be-comes quite long. The solution is to take the up and downsampling into account within the lter process. Since the up-sampled signal is usually generated by the insertion of zeros,the processing of these zeros can be omitted within the l-ter. This leads to the polyphase structure of Figure 4. Becausediff erent input/output ratios have to be realized for di ff er-ent standards, the number of lter coe ffi cients that must bestored may become large. If necessary, a direct computationof the lter coeffi cients can be more effi cient than their ad-vance storage [5]. After the sampling rate adaptation, the sig-nal is processed within the complex baseband unit (demod-ulation and decoding). The SDR data processing within thehigher protocol layers [ 6] is not considered in the present pa-per.

z 1 z 1 z 1

+ + +

g j g J + j g 2 J + j g (L 1) J + j

Figure 4: Polyphase lter for sampling rate adaptation.

The SDR transmitter branch consists of the proceduresinverse to that of the receiver branch. That is, the signal to betransmitted is generated as a complex baseband signal, fromwhich, for example, the real part is taken to be shifted to the(transmission) RF.

For SDRs, recongurability means that the radio is ableto process signals of diff erent standards or even signals thatare not standardized but exist in specic applications. Onemethod to implement recongurability is parameterizationof standards. We look at a communication standard as a setof documents that comprehensively describe all functions of a radio system in such a way that a manufacturer can de-velop terminals or infrastructure equipment on this basis.Standardization is one necessary condition to make a com-munication system successful on the market, as exempliedby GSM. Standardization pertains to all kinds of communi-cation systems, that is, especially to personal, local, cellular,or global wireless networks. Of course, a standard has to con-tain precise descriptions of all the functions of the system.Especially for a mobile system, both the air interface and theprotocol stack have to be specied. Parameterization meansthat everystandard is looked upon as one member of a family of standards [ 7]. The signal processing structure of the fam-ily is then developed in such a way that this structure may beswitched by parameters to realize the di ff erent standards.

When developing an SDR, one has to pay attention to thefact that there are substantial di ff erences between the second-generation FDMA/TDMA standards (GSM or IS-136), thethird-generation CDMA standards (UMTS or cdma2000),and the OFDM-modulated WLAN standards (IEEE 802 .11aor HiperLAN/2) (cf. Table 1). Within UMTS, spreading atthe transmitter and despreading at the receiver have to berealized. IFFT and FFT operations are necessary for WLANtransceivers. Aside from such fundamental di ff erences, sim-ilarities among communication standards are predominant.For example, when looking at the signal processing chains,we remark that the error correction codes of all the second-generation standards are very similar: a combination of ablock code for the most important bits and a convolutionalcode for the larger part of the voice bits is applied. Channelcoding for data transmission is done by a powerful convolu-tional code. UTRA, as a third-generation air interface, o ff ersnet data rates of up to 2 Mbps and guarantees BERs, of upto 10 6 for specic applications. To reach these BERs turbocodes are employed for data transmission. Of course, withinan SDR all these procedures have to be integrated into a gen-eral encoding/decoding structure. Also a common modula-tor/demodulator structure has to be specied. Solutions tothese tasks are given, for example, in [2, 3, 7].


6/21


4. THE SOFTWARE COMMUNICATIONSARCHITECTURE

The Joint Tactical Radio System (JTRS) represents the fu-ture (mobile) communications infrastructure of the US jointforces. Introducing JTRS stands for an essential step towardsthe unication of radio communication systems, the trans-parency of services, and the exchangeability of components.Thedevelopment of the JTRS is accompanied andsupervisedby the US forces Joint Program O ffice (JPO).

Development, production, and delivery continue to bethe tasks of competing industrial communications softwareand hardware suppliers. An important new aspect added by the JTRS set-up is that the suppliers are guided to aim fora most perfect interchangeability of components due to thesupervision function of the JPO. The tool used by the JPO isthe software communications architecture (SCA) [8], an openframework that prescribes the developing engineers how thehardware or software blocks have to act together within theJTRS. The communication devices emerging from this phi-losophy are clearly SDRs.

A major group of suppliers and developers of communi-cation software and hardware founded the SDR Forum [ 9] topromote their interests. The importance of the SDR Forum,however, reaches well beyond the application of SDRs in theJTRS. This is underlined by the SDR Forum membership of European and Asian industrial and research institutions thatusually are mainly interested in the evolution of commercialmobile communication networks.

The SCA describes how waveformsare to be implementedonto appropriate hardware devices. A waveform is denedby the determination of the lower three layers (network,data link, physical) of the ISO/OSI model. Therefore, wave-form is a synonym of standard or air interface. Based onthe waveform denition, a transmission method is com-pletely determined. The denition of a waveform, there-fore, lays down the modulation, coding, access, and duplex modes as well as the protocol structure of the transmissionmethod.

The SCA denes the software structure of an SDR thatmay be usable within the JTRS. The underlying hardwareas well as the software is described in object-oriented terms.Moreover, the structures of application program interfaces(APIs) and of the security environment are described. Eachcomponent has to be documented in a generally accessibleform.

The JTRS operating environment (OE) dened in theSCA consists of three main components:

(i) a real-time operating system,(ii) a real-time request broker,

(iii) the SCA core framework.

When developing an SCA compliant radio device thesupplier gets the operating system and the CORBA middle-ware from the commercial market. The core framework aswell as the waveform is developed by him or he also gets itfrom the market or (in future) it may be contributed by theJPO.

The SCA is the description of an open architecture withdistributed components. It strictly separates applications(waveforms) from the processing platform (hardware, oper-ating system, object request broker, core framework). It seg-ments the application functions and denes common inter-faces for the management and the employment of software

components. It denes common services and makes use of APIs to support the portability of hardware and softwarecomponents and of applications.

The connections between the applications and the coreframework within the SCA are given by the APIs. Standard-ized APIs are essential in assuring the portability of applica-tions as well as for the exchangeability of devices. APIs guar-antee that application and service programs may commu-nicate with one another, independent of the operating sys-temand the programming language used. APIs arewaveformspecic since uniform APIs for all waveforms would be inef-cient for implementations with bounded resources. There-fore, the goal is to have a standard set of APIs for each wave-

form. The single APIs are essentially given by the layers of theISO/OSI model.(i) A PHY API supports initialization and conguration

of the system in non-real-time. In real-time it takes care of the transformation of symbols (or bits) to RF in the trans-mitter branch. In the receiver branch it transforms RF signalsto symbols (bits).

(ii) A MAC API supports all the MAC functions of theISO/OSI layer model (e.g., timeslot control in TDMA or FECcontrol).

(iii) An LLC API makes available an interface for thewaveforms link layer performance (according to the ISO/OSIlayer model: data link services) on component level.

(iv) A network API makes available an interface for thewaveforms network performance on component level.

(v) A security API serves for the integration of data secu-rity procedures (INFOSEC, TRANSEC).

(vi) An input/output API supports the input and outputof audio, video, or other data.

Thesecurity relevant SCA aspects are written down in theSCA security supplement [8]. The SCA security functions andalgorithms are of course dened with respect to the military security requirements of JTRS.

5. USER CENTRIC AND TECHNOLOGY CENTRICCOGNITIVE RADIO PROPERTIES

The description of CR given by Mitola and Maguire in theirseminal paper [ 10] mainly focuses on the radio knowledgerepresentation language (RKRL). CR is lookedupon asa smallpart of the physical world using and providing informationover very diff erent time scales. Equipped with various sen-sors, a CR acquires knowledge from its environment. Em-ploying software agents, it accesses data bases and contactsother sources of information. In this context, CR seems tobecome the indispensable electronic aid of its owner. Read-ing [10] leads to the impression that a CR must be a complex device that helps to overcomeall problems of everyday life, allthe same whether they are recognized by the CRs owner or


7/21


not. Of course, these visions as well as the recognition cycle for CRs in [11] are strongly intended to stimulate new researchand development. For a more pragmatic point of view, how-ever, we approach CR in a diff erent way.

The properties of CRs may be divided into two groups:

(i) user centric properties that comprise support func-tions like nding the address of an appropriate restau-rant or a movie theater, recommendation of a travelroute, or supervision of appointments,

(ii) technology centric properties like spectrum monitor-ing, localization, and tracking, awareness of processingcapabilities for the partitioning or the scheduling of processes, information gathering, and knowledge pro-cessing.

From our point of view, many of the user centric proper-ties can be implemented by using queries to data bases. Thistype of intelligence can be kept in the networks and activatedby calls. In transceiver development, much more di ffi cult de-

sign choices need to be made to realize the wanted technol-ogy centric properties of a CR. Therefore, we concentrate onthe latter in the following sections.

6. THE NEED FOR ADVANCED SPECTRUMMANAGEMENT

Today, spectrum is regulated by governmental agencies. Spec-trum is assigned to users or licensed to them on a long-term basis normally for huge regions like countries. Doingthis, resources are wasted, because large-frequency regionsare used very sporadically. The vision is to assign appropriateresources to end users only as long as they are needed for a

geographically bounded region, that is, a personal, local, re-gional, or global cell. The spectrum access is then organizedby the network, that is, by the users. First examples for self-regulation in mobile radio communications are to be foundin the ISM (24002483 .5 MHz) and in the WLAN (51505350MHz and 54705725MHz) bands.

Future advanced spectrum management will comprise[12] the following.

(i) Spectrum reallocation: the reallocation of bandwidthfrom government or other long-standing users to new services such as mobile communications, broadbandinternet access, and video distribution.

(ii) Spectrum leases: the relaxation of the technical andcommercial limitations on existing licensees to usetheir spectrum for new or hybrid (e.g., satellite andterrestrial) services and granting most mobile radio li-censees the right to lease their spectrum to third par-ties.

(iii) Spectrum sharing : the allocation of an unprecedentedamount of spectrum that could be used for unlicensedor shared services.

If we look upon the users behavior in an FDMA/TDMAsystem over the time/frequency plane (cf. Figure 5), wemay nd out that a considerable part of the area remains

f 0

f u

F r e q u e n c y

0 Time

Figure 5: FDMA/TDMA signals over the time/frequency plane,spectrum pool.

unused [ 12, 13]. This unused area marks the pool from

which frequencies can be allocated to secondary users (SUs),for example, in a hotspot. In the following we denote theFDMA/TDMA users as primary users (PUs). In order tomake the implementation of the SUs system into the PUssystem feasible, two main assumptions should be fullled:

(i) the PUs system is not disturbed by the SUs system,(ii) the PUs system remains unchanged (i.e., all signal

processing that has to be done to avoid disturbancesof the PUs communications must be implemented inthe SUs system).

Now we assume that the transmission method within theSUs system is OFDM. Figure 6 gives a brief overview over anOFDM transmitter: the sequential data stream is convertedto a parallel stream, the vectors of which are interpreted assignals in the frequency domain. By applying an inverse fastFourier transform (IFFT), these data are transformed intothe time domain and sent over the air on a set of orthogonalcarriers with separation f on the frequency axis. If somecarriers should not be used, it is necessary to transmit zeroson these carriers. This is the strategy to protect the PUs sys-tem from disturbances originating from the SUs system. Inorder to make the SUs system work, the following problemshave to be solved.

(i) The reliable detection of upcoming PUs signalswithin an extremely short time interval. (This means thatthe detection has to be performed with a very high detectionprobability ensuring a moderate false alarm probability.)

(ii) The consideration of hidden stations.(iii) The signaling of the present transmission situation

in the PUs system to all stations of the SUs system such thatthese do not use the frequencies occupied by the PUs.

The solutions to these problems have recently been found[13]. The keywords for these solutions are distributed detec-tion, boosting of the detection results and combining themin the hotspots access point to an occupancy vector, and dis-tributing the occupancy vector to all mobile stations in thehotspot.


8/21


Bitsequence

1

m

...

1

m

...

1

m

...

Cod

Cod

Cod S e r i a l - t o - p a r a l l e

l c o n v e r s

i o n

I D F T ( I F F T )

P a r a

l l e l - t o - s e r

i a l c o n v e r s

i o n

D/A RF-Mod.

(a)

f

f 3 f 2 f 1 f 0 f 1 f 2 f 3 f

(b)

Figure 6: OFDM. (a) Transmitter. (b) Spectrum.

The central point in our present discussion is that the SUssystems transceivers have in some sense to act like CRs. They have to sense their spectral neighborhood for PUs signals

and to react upon their ndings.

7. TECHNOLOGY CENTRIC COGNITIVE RADIO

In a more advanced spectrum sharing system, CRs have toapply more advanced algorithms. If a portion of the spec-trum may be accessed by any access mode, the followingprocedure becomes imaginable: starting from the transmis-sion demand of its user, the CR decides about the data rate,the transmission mode, and therefore about the bandwidthof the transmission. Afterwards it has to nd an appropri-ate resource for its transmission. This presumes that the CR knows where it is (self-location), what it is able to do (self-awareness), and where the reachable base stations are. To getmore information about possible interferences it should, forexample, be able to detect signals active in adjacent frequency bands and to recognize their transmission standards [ 14].

Summing up, a CR should have implemented the follow-ing technologies (possibly among others):

(i) location sensors(e.g., GPS or Galileo);(ii) equipment to monitor its spectral environment in an

intelligent 2 way;

2Intelligent means that searching for usable frequency bands is not doneby just scanning the whole spectrum.

Control SDR

core

Spectrum

monitoringLocalization

Information and knowledge processing

Figure 7: Technology centric cognitive radio.

(iii) in order to track the locations or the spectral environ-ments developments, learning and reasoning algorithms haveto be implemented;

(iv) when complying with a communications etiquette, ithas to listen before talkas well as to prevent the disturbanceof hidden stations;

(v) in order to be fair it has to compromise its own de-mands with the demands of other users, most probably inmaking decisions in a competitive environment using the re-sults of game theory [15];

(vi) it has to keep its owner informed via a highly sophis-ticated man-machine interface.

A rst block diagram of a technology centric CR is givenin Figure 7. One of the most important decisions that have tobe made in an open access environment is whether a controlchannel is to be implemented or not. The most challengingdevelopment is that of the information and knowledge pro-cessing.

8. CONCLUSIONS

Standardization of a transmission mode is necessary to en-sure its success on the market. From standards we can learnabout the main parameters of a system and, by comparingdiff erent standards, we may conclude about similarities anddissimilarities within their signal processing chains. Keep-ing this knowledge in mind, we are able to construct PaC-SDRs. A far more general setup is given by the SCA which isa framework for the recongurablity of transceivers and forthe portability of waveforms from one hardware platform toanother. Starting from SDRs, the next step in the evolutionof intelligent transmission devices leads to CRs that may belooked upon as a small part of the physical world using andproviding information over very di ff erent time scales. Sincethis approach seems to be very futuristic, we take a look atthe urgent problem of e ffi cient spectrum usage. In order tointroduce advanced spectrum management procedures (e.g.,spectrum pooling), the employment of CRs that at least areable to monitor their electromagnetic environments and totrack their own locations is necessary. Therefore, the devel-opment of technology centric CRs is proposed here as a rststep towards general CRs.


9/21


ACKNOWLEDGMENT

Theauthorgratefullyacknowledges the inuence that the6thEuropean Frameworks IntegratedProject End-to-End Recon- gurability (E2R) as well as the Software-Dened Radio Fo-rum have on his present work.

REFERENCES

[1] C. Heegard and S. B. Wicker, Turbo Coding , Kluwer Academic,Boston, Mass, USA, 1999.

[2] F. K. Jondral, Parametrizationa technique for SDR imple-mentation, in Software Dened RadioEnabling Technolo- gies, W. Tuttlebee, Ed., pp. 232256, John Wiley & Sons, Lon-don, UK, 2002.

[3] A. Wiesler and F. K. Jondral, A software radio for second-andthird-generation mobile systems, IEEE Trans. Veh. Technol.,vol. 51, no. 4, pp. 738748, 2002.

[4] P. Rykaczewski, D. Pienkowski, R. Circa, and B. Steinke, Sig-nal path optimization in software dened radio systems,IEEE Trans. Microwave Theory Tech., vol. 53, no. 3, pp. 1056

1064, 2005.[5] T. Hentschel and G. Fettweis, Sample rate conversion forsoftware radio, IEEE Commun. Mag., vol. 38, no. 8, pp. 142150, 2000.

[6] M. Sieber, Design of a generic protocol stack for an adaptiveterminal, in Proc. 1st Karlsruhe Workshop on Software Radios,pp. 3134, Institut f ur Nachrichtentechnik, Universit at Karl-sruhe (TH), Karlsruhe, Germany, March 2000.

[7] F. K. Jondral, R. Machauer, and A. Wiesler, Software Radio Adaptivit at durch Parametrisierung , J. Schlembach Fachverlag,Weil der Stadt, Germany, 2002.

[8] Software communications architecture specication, jtrs-5000sca v3.0, Joint Tactical Radio System (JTRS)Joint Program O ffice, August 2004, available online onhttp://jtrs.army.mil .

[9] Software Dened Radio Forum, available online onhttp://www.sdrforum.org .

[10] J. Mitola III and G. Q. Maguire, Cognitive radio: makingsoftware radios more personal, IEEE Pers. Commun., vol. 6,no. 4, pp. 1318, 1999.

[11] J. Mitola III, Cognitive radio: an integrated agent architec-ture for software denedradio, Ph.D. dissertation, ComputerCommunication System Laboratory, Department of Telein-formatics, Royal Institute of Technology (KTH), Stockholm,Sweden, May 2000.

[12] G. Staple and K. Werbach, The end of spectrum scarcity,IEEE Spectr., vol. 41, no. 3, pp. 4852, 2004.

[13] T. A. Weiss and F. K. Jondral, Spectrum pooling: an inno-vative strategy for the enhancement of spectrum e fficiency,

IEEE Commun. Mag., vol. 42, no. 3, pp. 814, 2004.[14] M. Oner and F. K. Jondral, Air interface recognition for asoftware radio system exploiting cyclostationarity, in Proc.15th IEEE International Symposium on Personal, Indoor and Mobile Radio Communications (PIMRC 04), vol. 3, pp. 19471951, Barcelona, Spain, September 2004.

[15] J. Neel, J. Reed, and R. Gilles, The role of game theory inthe analysis of software radio networks, in Proc. Software De- ned Radio Forum Technical Conference and Product Exhibi-tion (SDR 02), vol. 2, pp. NP302, San Diego, Calif, USA,November 2002.

[16] J. Mitola III, Software Radio Architecture: Object-Oriented Ap- proaches to Wireless Systems Engineering , John Wiley & Sons,New York, NY, USA, 2000.

[17] J. Mitola III and Z. Zvonar, Eds., Software Radio Technologies:Selected Readings, John Wiley & Sons, New York, NY, USA,2000.

[18] J. Mitola III and W. Tuttlebee, Eds., Software Dened Radio:Origins, Drivers and International Perspectives, John Wiley &Sons, Chichester, UK, 2002.

[19] W. Tuttlebee, Ed., Software Dened Radio: Enabling Technolo-

gies, John Wiley & Sons, Chichester, UK, 2002.[20] M. Dillinger, K. Madani, andN. Alonistioti,Eds., SoftwareDe- ned Radio: Architectures, Systems and Functions, John Wiley & Sons, Chichester, UK, 2003.

[21] J. Reed, Software Radioa Modern Approach to Radio Engi-neering , Prentice-Hall, Upper Saddle River, NJ, USA, 2002.

[22] H. Harada and R. Prasad, Simulation and Software Radio for Mobile Communications, Artech House, Boston, Mass, USA,2002.

[23] S. Haykin, Cognitive radio: brain-empowered wireless com-munications, IEEE J. Select. Areas Commun., vol. 23, no. 2,pp. 201220, 2005.

Friedrich K. Jondral received a Diploma

and a Doctoral degree in mathematics fromthe Technische Universit at Braunschweig,Germany, in 1975 and 1979, respectively.During the winter semester 1977/78, he wasa Visiting Researcher in the Departmentof Mathematics, Nagoya University, Japan.From 1979 to 1992, Dr. Jondral was an em-ployee of AEG-Telefunken (now EuropeanAeronautic Defence and Space Company (EADS)), Ulm, Germany, where he held various research anddevel-opment, as well as management positions. Since 1993, Dr. Jondralhas been Full Professor and Head of the Institut f ur Nachrichten-technik at the Universit at Karlsruhe (TH), Germany. There, from2000 to 2002, he served as the Dean of the Department of Electri-cal Engineering and Information Technology. During the summersemester of 2004, Dr. Jondral was a Visiting Faculty in the Mobileand Portable Radio Research Group of Virginia Tech, Blacksburg,Va. His current research interests are in the elds of ultra-wide-band communications, software-dened and cognitive radio, sig-nal analysis, pattern recognition, network capacity optimization,and dynamic channel allocation. Dr. Jondral is a Senior Memberof the IEEE; he currently serves as an Associate Editor of the IEEECommunications Letters and as a Member of the Software-DenedRadio Forums Board of Directors.
http://jtrs.army.mil/http://jtrs.army.mil/http://www.sdrforum.org/http://www.sdrforum.org/http://www.sdrforum.org/http://jtrs.army.mil/


10/21

EURASIP JOURNAL ON WIRELESS COMMUNICATIONS AND NETWORKING

Special Issue on

Quality of Service in Mobile Ad Hoc Networks

Call for PapersMobile ad hoc networking is a challenging task due to alack of resources residing in the network as well as frequentchanges in network topology. Although much research hasbeen directed to supporting QoS in the Internet and tradi-tional wireless networks, present results are not suitable formobile ad hoc network (MANET). QoS support for mobilead hoc networks remains an open problem, drawing interest

from both academia and industry under military and com-mercial sponsorship. MANETs have certain unique charac-teristics that pose several difficulties in provisioning QoS,such as dynamically varying network topology, lack of pre-cise state information, lack of central control, error-proneshared radio channels, limited resource availability, hiddenterminal problems, and insecure media, and little consen-sus yet exists on which approaches may be optimal. FutureMANETs are likely to be multimode or heterogeneous innature. Thus, the routers comprising a MANET will employ multiple, physical-layer wireless technologies, with each new technology requiring a multiple-access (MAC) protocol forsupporting QoS. Above the MAC layer, forwarding, routing,signaling, and admission control policies are required, andthe best combination of these policies will change as the un-derlying hardware technology evolves.

The special issue solicits original papers dealing with state-of-the-art and up-to-date e ff orts in design, performanceanalysis, implementation and experimental results for vari-ous QoS issues in MANETs. Fundamental research results aswell as practical implementations and demonstrators are en-couraged.

Topics of interest include (but are not limited to):

QoS models and performance evaluation of MANET QoS resource reservation signaling Various QoS routing protocols Flexible MAC protocols Robust modeling and analysis of MANET resource

management Dynamic and hybrid resource allocation schemes Resource control and multimedia QoS support Channel characterization QoS management and tra ffi c engineering

Tools and techniques for MANET measurement andsimulation

Adaptive QoS provisioning issues Information assurance and reliability in MANET

Authors should follow the EURASIP JWCN manuscriptformat described at http://www.hindawi.com/journals/wcn/.

Prospective authors shouldsubmit an electronic copy of theircomplete manuscript through the EURASIP JWCN manu-script tracking system at http://www.mstracking.com/wcn/,according to the following timetable:

Manuscript Due August 1, 2005

Acceptance Notication December 1, 2005

Final Manuscript Due February 1, 2006

Publication Date 2nd Quarter, 2006

GUEST EDITORS:

Wei (Wayne) Li , Department of Electrical Engineering andComputer Science, The University of Toledo, Toledo, OH43606, USA; [email protected] Guizani , Department of Computer Science,Western Michigan University, Kalamazoo, MI 49008, USA;[email protected] Kazakos , Department of Electrical andComputer Engineering, University of Idaho, Moscow, ID83844, USA; [email protected]

Hindawi Publishing Corporationhttp://www.hindawi.com


11/21


Special Issue on

CMOS RF Circuits for Wireless Applications

Call for PapersAdvanced concepts for wireless communications present avision of technology that is embedded in our surround-ings and practically invisible, but present whenever required.From established radio techniques like GSM, 802.11, or Blue-tooth to more emerging ones like ultra-wideband (UWB)

or smart dust moats, a common denominator for futureprogress is underlying CMOS technology. Although the useof deep-submicron CMOS processes allows for an unprece-dented degree of scaling in digital circuitry, it complicatesimplementation and integration of traditional RF circuits.The explosive growth of standard cellular radios and rad-ically diff erent new wireless applications makes it impera-tive to nd architectural and circuit solutions to these designproblems.

Two key issues for future silicon-based systems are scale of integration and ultra-low power dissipation. The concept of combining digital, memory, mixed-signal, and RF circuitry on one chip in the form of System-on-Chip (SoC) has been

around for a while. However, the diffi

culty of integrating het-erogeneous circuit design styles and processes onto one sub-strate still remains. Therefore, System-in-Package (SiP) con-cept seems to be gaining more acceptance.

While it is true that heterogeneous circuits and architec-tures originally developed for their native technologies can-not be eff ectively integrated as is into a deep-submicronCMOS process, one might ask the question whether thosefunctions can be ported into more CMOS-friendly architec-tures to reap all the benets of the digital design and ow. It isnotpredestined that RF wireless frequency synthesizersbe al-ways charge-pump-based PLLs with VCOs, RF transmit up-converters be I/Q modulators, receivers use only Gilbert cell

or passive continuous-time mixers. Performance of modernCMOS transistors is nowadays good enough for multi-GHzRF applications.

Low power has always been important for wireless com-munications. With new developments in wireless sensor net-works and wireless systems for medical applications, thepower dissipation is becoming a number one issue. Wire-less sensor network systems are being applied in critical ap-plications in commerce, healthcare, and security. These sys-

tems have unique characteristics and face many implemen-tation challenges. The requirement for long operating life fora wireless sensor node under limited energy supply imposesthe most severe design constraints. This calls for innovativedesign methodologies at the circuit and system level to ad-

dress this rigorous requirement.Wireless systems for medical applications hold a numberof advantages over wired alternatives, including the ease of use, reduced risk of infection, reduced risk of failure, reducedpatient discomfort, enhanced mobility, and lower cost. Typ-ically, applications demand expertise in multiple disciplines,varying from analog sensors to digital processing cores, sug-gesting opportunities for extensive hardware integration.

The special issue will address the state of the art in CMOSdesign in the context of wireless communication for 3G/4Gcellular telephony, wireless sensor networks, and wirelessmedical applications.

Topics of interest include (but are not limited to):

Hardware aspects of wireless networks Wireless CMOS circuits for healthcare and

telemedicine Modulation schemes for low-power RF transmission RF transceiver architectures (low IF, direct conver-

sion, super-regenerative) RF signal processing Phase-locked loops (PLLs) Digitally controlled oscillators LNAs, mixers, charge pumps, and VCOs in CMOS System-on-Chip (SoC) and System-in-Package (SiP)

implementations RF design implementation challenges in

deep-submicron CMOS processes

Authors should follow the EURASIP JWCN manuscriptformat described at http://www.hindawi.com/journals/wcn/.Prospective authors shouldsubmit an electronic copy of theircomplete manuscript through the EURASIP JWCN manu-script tracking system at http://www.mstracking.com/wcn/,according to the following timetable:


12/21

Manuscript Due September 1, 2005

Acceptance Notication January 1, 2006Final Manuscript Due April 1, 2006

Publication Date 2nd Quarter, 2006

GUEST EDITORS:

KrisIniewski , Departmentof Electrical andComputer Engi-neering, University of Alberta, ECERF Building, Edmonton,AB, Canada T6G 2V4; [email protected] El-Gamal , Department of Electrical and Com-

puter Engineering, McGill University, McConnell Engineer-ing Building, Room 633, 3480 University Street, Montreal,QC, Canada H3A 2A7; [email protected] Bogdan Staszewski , Texas Instruments, Dallas, TX 75243, USA; [email protected]



13/21


Special Issue on

Ultra-Wideband (UWB) CommunicationSystemsTechnology and Applications

Call for PapersThe opening of unlicensed frequency band between 3.1 GHzand 10.6 GHz (7.5 GHz) for indoor wireless communica-tion systems by the Federal Communications Commission(FCC) spurred the development of ultra-wideband (UWB)communications. Several wireless personal area networking(WPAN) products have been demonstrated recently. Theseproducts implement one of the two leading proposals to theIEEE 802.15.3a High-Speed WPAN Standards Committee.On the other hand, the IEEE 802.15.4a Standards Commit-tee is focusing on low power, low bit rate applications, em-phasizing accurate localization. This urry of activity hasdemonstrated the feasibility of high-bit-rate and low-bit-rate/low-power UWB communications. Further improve-ment in UWB transmission speed and reductions in powerconsumption and UWB transceiver cost require a compre-hensive investigation of UWB communications that simul-taneously addresses system issues, analog and digital imple-mentation constraints, and RF circuitry limitations. In theapplication area, coexistence with other wireless standardsplays an important role.

The aim of this special issue is to present recent researchin UWB communication systems with emphasis on futureapplications in wireless communications. Prospective papersshould be unpublished and present novel innovative contri-butions from either a methodological or an application per-spective.

Suggested topics include (but are not limited) to:

UWB channel modeling and measurement High-bit-rate UWB communications UWB modulation and multiple access Synchronization and channel estimation Pulse shaping and ltering UWB transceiver design and signal processing Interference and coexistence Ultra-low-power UWB transmission MIMO-UWB Multiband UWB Spectral management

UWB wireless networks and related issues Ranging and positioning Applications

Authors should follow the EURASIP JWCN manuscript

format described at http://www.hindawi.com/journals/wcn/.Prospective authors shouldsubmit an electronic copy of theircomplete manuscript through the EURASIP JWCN manu-script tracking system at http://www.mstracking.com/wcn/,according to the following timetable:

Manuscript Due September 1, 2005

Acceptance Notication February 1, 2006

Final Manuscript Due May 1, 2006

Publication Date 3rd Quarter, 2006

GUEST EDITORS:

Nallanathan Arumugam , Department of Electrical andComputer Engineering, National University of Singapore,10 Kent Ridge Crescent, Singapore 119260;[email protected] Svensson , Chalmers University of Technology,Department of Signals and Systems, 41296, Gteborg,Sweden; [email protected]. H. Tewk , Department of Electrical Engineering,University of Minnesota, 4-174 EE/CSCI Building, 200Union st. SE, Minneapolis, MN 55455; [email protected]



14/21


Special Issue on

Wireless Network Security

Call for PapersRecent advances in wireless network technologies haverapidly developed in recent years, as evidenced by wire-less location area networks (WLANs), wireless personal areanetworks (WPANs), wireless metropolitan area networks(WMANs), and wireless wide area networks (WWANs), thatis, cellular networks. A major impediment to their deploy-ment, however, is wireless network security. For example,

the lack of data condentiality in wired equivalent privacy (WEP) protocol has been proven, and newly adopted stan-dards such as IEEE 802.11i robust secruity network (RSN)and IEEE 802.15.3a ultra-wideband (UWB) are not fully tested and, as such, may expose unforeseen security vulner-abilities. The eff ort to improve wireless network security islinked with many technical challenges including compatibil-ity with legacy wireless networks, complexity in implemen-tation, and cost/performance trade-o ff s. The need to addresswireless network security and to provide timely, solid techni-cal contributions establishes the motivation behind this spe-cial issue.

This special issue will focus on novel and functional ways

to improve wireless network security. Papers that do not fo-cus on wireless network security will not be reviewed. Spe-cic areas of interest in WLANs, WPANs, WMANs, andWWANs include, but are not limited to:

Attacks, security mechanisms, and security services Authentication Access control Data condentiality Data integrity Nonrepudiation Encryption and decryption Key management Fraudulent usage Wireless network security performance evaluation Wireless link layer security Tradeo ff analysis between performance and security Authentication and authorization for mobile service

network Wireless security standards (IEEE 802.11, IEEE

802.15, IEEE 802.16, 3GPP, and 3GPP2)


Manuscript Due October 1, 2005Acceptance Notication February 1, 2006

Final Manuscript Due May 1, 2006


GUEST EDITORS:

Yang Xiao , Computer Science Division, The University of Memphis, Memphis, TN 38152, USA; [email protected] Lin , Departmentof ComputerScience andInforma-

tion Engineering, National Chiao Tung University, Taiwan;[email protected] Ding-Zhu Du , Department of Computer Science & Engi-neering, University of Minnesota, Minneapolis, MN 55455,USA; [email protected]



15/21


Special Issue on

Radio Resource Management in 3G+ Systems

Call for PapersThe 3G+ wireless systems can be characterized by aggregatebit rates in the range of Mbps, QoS support for interactivemultimedia services, global mobility, service portability, en-hanced ubiquity, and larger user capacity. All digital entirely packet-switched radio networks involving hybrid network-ing and access technologies are envisioned in 3G+ systems.In such systems, radio resource management (RRM) plays a

major role in the provision of QoS and effi

cient utilizationof scarce radio resources. With the required support for mul-timedia services to multiple users over diverse wireless net-works and ever-increasing demand for high-quality wirelessservices, the need for eff ective and effi cient RRM techniquesbecomes more important than ever. The addition of e ffi cientpacket data channels in both forward and reverse directionsand QoS support in 3G standards leads toa moreexible net-work, but at the same time increases the complexity of deter-mining the optimal allocation of resources especially on theradio interface. This special issue is devoted to addressing theurgent and important need for e fficient and e ff ective RRMtechniques in the evolving next-generation wireless systems.

We are seeking original, high-quality, andunpublished pa-pers representing the state-of-the-art research in radio re-source management aspects of the next-generation wirelesscommunication systems. Topics of interests include, but arenot limited to:

Resource optimization for multimedia services Rate allocation and adaptation Transmit power control and allocation Intelligent scheduling Subcarrier allocation in multicarrier systems Antenna selection techniques in MIMO systems Call admission control Load balancing, congestion, and ow control in radionetworks Modeling and analysis of QoS in wireless networks Adaptive QoS control for wireless multimedia Delay and jitter management in wireless networks Hando ff and mobility management RRM techniques in hybrid radio networks Distributed versus centralized RRM

RRM in mesh networks Cross-layer optimization of radio resources H-ARQ techniques and issues Performance of multihop and cooperative networks Challenges in implementation of VoIP over radio net-

works Experimental and implementation issues


Manuscript Due October 1, 2005

Acceptance Notication February 1, 2006

Final Manuscript Due May 1, 2006Publication Date 3rd Quarter, 2006

GUEST EDITORS:

Alagan Anpalagan , Department of Electrical andComputer Engineering, Ryerson University, 350 VictoriaStreet, Toronto, ON, Canada M5B 2K3;[email protected] Vannithamby , Ericsson Inc., 5012 Wateridge VistaDrive, San Diego, CA 92126, USA;

[email protected] Zhuang , Department of Electrical and ComputerEngineering, University of Waterloo, 200 University AvenueWest, Waterloo, ON, Canada N2L 3G1;[email protected] Aissa , INRS-EMT, Universit du Qubec, PlaceBonaventure, 800 Gauchetiere Ouest, Suite 6900, Montreal,QC, Canada H5A 1K6; [email protected]



16/21


Special Issue on

Multiuser Cooperative Diversity for Wireless Networks

Call for PapersMultihop relaying technology is a promising solution for fu-ture cellular and ad-hoc wireless communications systems inorder to achieve broader coverage and to mitigate wirelesschannels impairment without the need to use large power atthe transmitter. Recently, a new concept that is being actively studied in multihop-augmented networks is multiuser coop-erative diversity, where several terminals form a kind of coali-

tion to assist each other with the transmission of their mes-sages. In general, cooperative relaying systems have a sourcenode multicasting a message to a number of cooperative re-lays,which in turn resend a processed version to the intendeddestination node. The destination node combines the signalreceived from the relays, possibly also taking into account thesources original signal. Cooperative diversity exploits twofundamental features of the wireless medium: its broadcastnature and its ability to achieve diversity through indepen-dent channels. There are three advantages from this:

(1) Diversity. This occurs because di ff erentpaths are likely to fade independently. The impact of this is expectedto be seen in the physical layer, in the design of a re-ceiver that can exploit this diversity.

(2) Beamforming gain. The use of directed beams shouldimprove the capacity on the individual wireless links.The gains may be particularly signicant if space-timecoding schemes are used.

(3) Interference Mitigation. A protocol that takes advan-tage of the wireless channel and the antennas and re-ceivers available could achieve a substantial gain insystem throughput by optimizing the processing donein the cooperative relays and in the scheduling of re-transmissions by the relays so as to minimize mutualinterference and facilitate information transmissionby cooperation.

The special issue solicits original research papers dealingwith up-to-date e ff orts in design, performance analysis, im-plementation and experimental results of cooperative diver-sity networks.

We seek original, high-quality, and unpublished papersrepresenting the state-of-the-art research in the area of mul-tiuser cooperative diversity as applied to the next generation

multihop wireless communication systems. We encouragesubmission of high-quality papers that report original work in both theoretical and experimental research areas.

Topics of interests include, but are not limited to:

Information theoretic aspects of cooperative diversity Cooperative diversity from the standpoint of

multiuser information theory: Shannon capac-ity

Cooperative diversityand its relation to network coding

Security aspects Physical layer and networking aspects of cooperative

diversity Cooperative protocols for wireless relay, ad hoc,

and sensor multihop networks Cross-layer protocol design Power allocation in networks with cooperative

diversity Reducing transmission energy and extending

terminal battery life in cooperative diversity net-

works Relay networks architectures

MIMO transmission and cooperative diversity net-works

Cooperative systems with space-time coding MIMO transmission in multihop networks Cooperative MIMO

Authors should follow the EURASIP JWCN manuscriptformat described at http://www.hindawi.com/journals/wcn/.Prospective authors shouldsubmit an electronic copy of theircomplete manuscript through the EURASIP JWCN manu-script tracking system at http://www.mstracking.com/wcn/,

according to the following timetable:

Manuscript Due November 1, 2005

Acceptance Notication March 1, 2006

Final Manuscript Due June 1, 2006



17/21

GUEST EDITORS:

George K. Karagiannidis , Department of Electrical andComputer Engineering, Aristotle University of Thessaloniki,54124 Thessaloniki, Greece; [email protected] Tellambura , Department of Electrical andComputer Engineering, University of Alberta, Edmonton,AB, Canada, T6G 2V4; [email protected] Mukherjee , Lucent Technologies, 600-700Mountain Avenue, Murray Hill, NJ 07974, USA;[email protected] O. Fapojuwo , Department of Electrical &Computer Engineering, The University of Calgary, 2500University Drive N.W., Calgary, AB, Canada, T2N 1N4;[email protected]



18/21

EURASIP JOURNAL ON EMBEDDED SYSTEMS

Special Issue on

Signal Processing with High Complexity:Prototyping and Industrial Design

Call for PapersSome modern applications require an extraordinary largeamount of complexity in signal processing algorithms. Forexample, the 3rd generation of wireless cellular systems is ex-pected to require 1000 times more complexity when com-pared to its 2nd generation predecessors, and future 3GPPstandardswill aim for even morenumber-crunchingapplica-tions. Video and multimedia applications do not only drivethe complexity to new peaks in wired and wireless systemsbut also in personal and home devices. Also in acoustics,modern hearing aids or algorithms for de-reverberation of rooms, blind source separation, and multichannel echo can-celation are complexity hungry. At the same time, the antic-ipated products also put on additional constraints like sizeand power consumption when mobile and thus battery pow-ered. Furthermore, due to new developments in electroa-coustic transducer design, it is possible to design very smalland eff ective loudspeakers. Unfortunately, the linearity as-sumption does not hold any more for this kind of loudspeak-ers, leading to computationally demanding nonlinear cance-lation and equalization algorithms.

Since standard design techniques would either consumetoo much time or do not result in solutions satisfying allconstraints, more e ffi cient development techniques are re-quired to speed up this crucial phase. In general, such de-velopments are rather expensive due to the required extraor-dinary high complexity. Thus, de-risking of a future productbased on rapid prototyping is often an alternative approach.However, since prototyping would delay the development, itoften makes only sense when it is well embedded in the prod-uct design process. Rapid prototyping has thus evolved by applying new design techniques more suitable to support aquick time to market requirement.

This special issue focuses on new development meth-ods for applications with high complexity in signal process-ing and on showing the improved design obtained by suchmethods. Examples of such methods are virtual prototyp-ing, HW/SW partitioning, automaticdesign ows, oat to x conversions, automatic testing and verication, and poweraware designs.

Authors should follow the EURASIP JES manuscriptformat described at http://www.hindawi.com/journals/es/.Prospective authors shouldsubmit an electronic copy of theircomplete manuscripts through the EURASIP JESs man-uscript tracking system at http://www.mstracking.com/es/,according to the following timetable:

Manuscript Due December 1, 2005

Acceptance Notication March 1, 2006

Final Manuscript Due June 1, 2006


GUEST EDITORS:

Markus Rupp , TU Wien, Gusshausstr. 25/389, A-1040Wien, Austria; [email protected] Kaiser , University of Duisburg-Essen, 47057Duisburg, Germany; [email protected] Schmidt , Harman Becker / Temic-SDS, Germany;[email protected] Jean-Francois Nezan , IETR/Image group Lab, France; [email protected]



19/21


Special Issue on

Field-Programmable Gate Arrays in Embedded Systems

Call for PapersField-Programmable Gate Arrays (FPGAs) are increasingly used in embedded systems to achieve high performance in acompact area. FPGAs are particularly well suited to process-ing data straight from sensors in embedded systems. Moreimportantly, the recongurable aspects of FPGAs give thecircuits the versatility to change their functionality based onprocessing requirements for di ff erent phases of an applica-tion, and for deploying new functionality.

Modern FPGAs integrate many di ff erent resources on asingle chip. Embedded processors (both hard and soft cores),multipliers, RAM blocks, and DSP units are all availablealong with recongurable logic. Applications can use theseheterogeneous resources to integrate several di ff erent func-tions on a single piece of silicon. This makes FPGAs particu-larly well suited to embedded applications.

This special issue focuses on applications that clearly show the benet of using FPGAs in embedded applications, as wellas on design tools that enable such applications. Specic top-icsof interest include the useof reconguration in embedded

applications, hardware/software codesign targeting FPGAs,power-aware FPGA design, design environments for FPGAs,system signalling and protocols used by FPGAs in embed-ded environments, and system-leveldesign targeting modernFPGAs heterogeneous resources.

Papers on other applicable topics will also be considered.All papers should address FPGA-based systems that are ap-propriate for embedded applications. Papers on subjects out-side of this scope (i.e., not suitable for embedded applica-tions) will not be considered.

Authors should follow the EURASIP JES manuscriptformat described at http://www.hindawi.com/journals/es/.Prospective authors should submit an electronic copy of their

complete manuscript through the EURASIP JES manuscripttracking system at http://www.mstracking.com/es/, accord-ing to the following timetable:

Manuscript Due December 15, 2005

Acceptance Notication May 1, 2006

Final Manuscript Due August 1, 2006

Publication Date 4th Quarter, 2006

GUEST EDITORS:

Miriam Leeser , Northeastern University, USA;[email protected] Hauck , University of Washington, USA;[email protected] Tessier , University of Massachusetts, Amherst,USA; [email protected]



20/21


Special Issue on

Synchronous Paradigm in Embedded Systems

Call for PapersSynchronous languages were introduced in the 1980s forprogramming reactive systems. Such systems are character-ized by their continuous reaction to their environment, ata speed determined by the latter. Reactive systems includeembedded control software and hardware. Synchronous lan-guages have recently seen a tremendous interest from lead-ing companies developing automatic control software and

hardware for critical applications. Industrial success storieshave been achieved by Schneider Electric, Airbus, DassaultAviation, Snecma, MBDA, Arm, ST Microelectronics, TexasInstruments, Freescale, Intel .... The key advantage outlinedby these companies resides in the rigorous mathematical se-mantics provided by the synchronous approach that allowssystem designers to develop critical software and hardwarein a faster and safer way.

Indeed, an important feature of synchronous paradigm isthat the tools and environments supporting development of synchronous programs are based upon a formal mathemat-ical model dened by the semantics of the languages. Thecompilation involves the construction of these formal mod-

els, andtheir analysis for staticproperties, their optimization,the synthesis of executable sequential implementations, andthe automated distribution of programs. It can also build amodel of the dynamical behaviors, in the form of a transitionsystem, upon which is based the analysis of dynamical prop-erties, for example, through model-checking-based verica-tion, or discrete controller synthesis. Hence, synchronousprogramming is at the crossroads of many approaches incompilation, formal analysis and verication techniques, andsoftware or hardware implementations generation.

We invite original papers for a special issue of the jour-nal to be published in the rst quarter of 2007. Papers may be submitted on all aspects of the synchronous paradigm for

embedded systems, including theory and applications. Somesample topics are:

Synchronous languages design and compiling Novel application and implementation of syn-

chronous languages Applications of synchronous design methods to em-

bedded systems (hardware or software)

Formal modeling, formal verication, controller syn-thesis, and abstract interpretation with synchronous-based tools

Combining synchrony and asynchrony for embed-ded system design and, in particular, globally asyn-chronous and locally synchronous systems

The role of synchronous models of computations in

heterogeneous modeling The use of synchronous modeling techniques in

model-driven design environment Design of distributed control systems using the syn-

chronous paradigm

Authors should follow the EURASIP JES manuscriptformat described at http://www.hindawi.com/journals/es/.Prospective authors shouldsubmit an electronic copy of theircomplete manuscripts through the EURASIP JESs man-uscript tracking system at http://www.mstracking.com/es/,according to the following timetable:

Manuscript Due June 1, 2006

Acceptance Notication October 1, 2006

Final Manuscript Due December 1, 2006

Publication Date 1st Quarter, 2007

GUEST EDITORS:

Alain Girault , INRIA, France; [email protected]. Ramesh , IIT Bombay, India; [email protected] Jean-Pierre Talpin , IRISA, France; [email protected]



21/21

:

In Salvador da Bahia, Brazil, 3-6 October 2005

I n t e r n a t i o n a l T e l e c o m m u n i c a t i o n U n i o n

Helping the world communicate

ITU T ELECOM A MERICAS 2005 combines the right technologies, information and people

at the regions most influential telecommunications event. Through a major Forum

and Exhibition, we provide the right platform for you to grow your business, network

with the industrys top names and help shape the future of telecommunications in the

Americas. [email protected] Tel.: +41 22 730 6161 Fax: +41 22 730 6444

Hosted by theGovernmentof Brazil

www.i tu. int /americas2 005

software defined radio_basics and evolution of cognitive radio

Documents