List of Machinery and Equipment for M.M.V.trade (Annexure A)

S.NO Name and description of article Quantity

(in Nos)

Rate per

unit

Amount

1. Steel rule 15 cm inch and metric 21-No’s

2. Steel rule 30 cm inch and metric -do-

3. Steel measuring tape 10 meter in a case 15

4. Try Square 10 cm Blade 21

5. Calipers outside 15 cm spring 21

6. Calipers inside 15 cm spring 21

7. Dividers 15 cm Spring 21

8. Safety glasses 21

9. Scriber 15 cm 21

10. Knife double Blade Electrician 21

11. Wire insulation Stripper for shinning

conductors from 0.4mm to 4mm

21

12. Electrician testing Pencil (Line / Neon

tester)

21

13. Electrician Screw Driver 250mm 19

14. Centre punch 10 cm. 21

15. Chisel cold flat 20 mm x 150 mm 21

16. Hammer ball peen 0.5 kg with handle 15

17. Screw driver 20cm.x 9mm. Blade 04

18. Screw driver 30 cm. x 9 mm. Blade 07

19. Spanner D.E. set of 12 pieces (6mm to

32mm)

05-sets

20. Pliers’ combination 20 cm.

13

21. Pliers side cutting 15 cm 11

22. Pliers round nose 15 cm 21

23. Pliers flat nose 15 cm

24. Hands file 20 cm. Second cut flat 21

25. Hand file 20 cm. Second cut half-round

21

26. Hand file 20 cm. smooth triangular 21

27. Hand file 30 cm. bastard 21

28. Hand file 30 cm. round bastard 21

29. File card or cleaner 21

B. Tool Instruments & general shop outfits

30. Wire cutter and stripper 21

31. Steel tool box with lock and key

(folding

type) 400x200x150 mm

15

1.

Outside micrometer 0 to 25 mm

01-No

2. Outside micrometer 25 to 50 mm 01

3. Outside micrometer 50 to 75 mm 01

4. Outside micrometer 75 to 100 mm

01

5. Internal micrometer 5 to 30 mm 01

6. Depth micrometer 0-25mm

01

7. Thread Micrometer 0-25mm

01

8. Drift Punch Copper 15 Cm

04

9. Prick Punch 15 cm

04

10. Adjustable micrometer sprit level to

measure flatness, indication and taper

with prismatic measuring base

01

11. Vernier caliper A 200 with inside and

depth measurement

01

12. Direct reading vernier caliper B 300

(direct reading with dial)

01

13.

Vernier depth Gauge 0-150 mm

01

14. Vernier height gauge 500 mm

01

15. Telescope gauge

01

16. Dial gauge type 1 Gr. A (complete with

clamping devices and stand

04

17. Surface gauge with dial test indicator

plunger type i.e. 0.01 mm

02

18. Cylinder bore gauge capacity 20 to 160

mm

02

19. Compression testing gauge suitable for

petrol engine.

02

20. Vacuum gauge to read 0 to 760 mm of

Hg.

02

21. Tyre pressure gauge with holding

nipple

02

22. Marking Material (Consumable)

23. Marking out table 90X60X90 cm. 01

24. CI surface plate 400 x 400 mm with

stand and cover

01

25. Granite surface plate 1600 x 1000 with

stand and cover

01

26. Steel rule 15 cm inch and metric 02

27. Steel rule 30 cm inch and metric 02

28. Try Square 10 cm Blade 02

29. Engineer’s square 15 cm. Blade 02

30. Calipers outside 15 cm spring 02

31. Caliper inside 15 cm Spring 02

32. Calipers 15 cm Hermaphrodite 02

33. Dividers 15 cm Spring 02

34. Scriber 15 cm 02

35. Scriber with scribing black universal 02

36. Chisels cross cut 200 mm X 6mm 02

37. Chisel 10 cm flat 02

38. Safety Goggles 02

39. Hollow Punch set of seven pieces 6mm

to 15mm

02-sets

each

40. Ball Peen Hammer 0.75 Kg 02

41. Hammer copper 1 Kg with handle 02

42. Hammer Mallet 02

43. Hammer Plastic 02

44. Hammer ball peen 0.25 kg with handle 02

45. Insulated Screw driver 30 cm x 9mm

blade

02

46. Insulated Screw driver 20 cm x 9mm

blade

02

47. Electric testing screw driver 02

48. Hand vice – 37 mm 02

49. Work bench 250 x 120 x 60 cm with 4

vices 12cm Jaw

01

50. Magnifying glass 75mm 02

51. V’ Block 75 x 38 mm pair with Clamps 02

52. Clamps C 100mm 02

53. Clamps C 150mm 02

54. Clamps C 200mm 02

55. Spanner, adjustable 15cm. 02

56. Spark plug spanner 14mm x 18mm x

Size

02

57. Adjustable spanner (pipe wrench 350

mm)

02

58. Spanner T. flocks for screwing up and

up-screwing inaccessible

positions

01

59. Spanner Clyburn 15 cm 01

60. Spirit level 2V 250, 05 metre 02

61. Angle plate size 200x100x200mm 02

62. Angle plate adjustable 250x150x175 01

63. Solid Parallels in pairs (Different size)

in Metric

02

64. Pliers combination 20 cm. 02

65. Pliers side cutting 15 cm 02

66. Pliers round nose 15 cm 02

67. Pliers flat nose 15 cm 02

68. Vice grip pliers 02

69. Circlip pliers Expanding and

contracting type 15cm and 20cm

each

02

70. Grip Wrench 200mm 02

71. Workshop plain goggles 21

72. Air impact wrench 01

73. Air ratchet 01

74. Air chisel 01

75. Air blow gun 01

76. Car Jet washer 01

77. Pipe flaring tool 01

78. Pipe cutting tool 01

79. Cleaning tray 45x30 cm. 04

80. Cleaning tray- Aluminum 45 x 30 cm 04

81. Stud extractor set of 3 02-sets

82. Stud remover with socket handle 01

83. Rivets sets snap and dolly combined

3mm, 4mm, 6mm

02-each

84. Chemical compound for fasteners

(Consumable)

06

85. Paraffin pressure Gun 02

86. Grease Gun 02

87. Hacksaw frame adjustable 20-30 cm 02

88. Hacksaw blade (consumable) 100

89. Flat File 20 cm & 35 cm bastard 04 each

90. Files assorted sizes and types including

safe edge file (20 Nos)

02-sets

91. Drill Twist (assorted) (Consumables) 10

92. Drill twist 1.5mm to 15mm (various

sizes) 0.5mm

04

93. Drill point angle gauge 01

94. Set of stock and dies - UNC, UNF and

metric

02-sets

95. Taps and wrenches - UNC, UNF and

metric

02-sets

96. Taps and Dies complete sets (5 types) 01 set

97. Hand reamers adjustable 10.5 to 11.25

mm, 11.25 to 12.75 mm,

12.75 to 14.25 mm and 14.25 to 15.75

mm

02-sets

98. Lapping abrasives (consumable) 50

99. Oil can 0.5/0.25 liter capacity 02

100. Oil Stone 15 cm x 5 cm x 2.5 cm 10

101. Different type gasket material

(consumable)

102. Different type of oil seal (consumable)

103. Sheet Metal Gauge 02

104. Straight edge gauge 2 ft. 01

105. Straight edge gauge 4 ft. 01

106. Thread pitch gauge metric, BSX, BSF,

MC, MF & SAE

01

107. Valve Lifter 01

108. Ladle 150mm Dia 01

109. Blow Lamp 1 litre 02

110. Crow bar 910 x25mm 02

111. Voltmeter 50V/DC 05

112. Ammeter 300A/ 60A DC with external

shunt

05

113. DC Ohmmeter 0 to 300 Ohms, mid

scales at 20 Ohms

01

114. Electric Soldering Iron 230 V 60 watts

230 V 25 watts

02-each

115. Copper bit soldering iron 0.25 Kg 05

116. Thimbles of different sizes 02

117. Wire Gauge (metric) 05

118. Hand operated crimping tool (i) for

crimping up to 4mm and (ii)

for crimping up to 10mm

02

119. Hand rubber gloves tested for 5000 V 05-pairs

120. Holders, lamp teakwood boards, plug

sockets, solders, flux wires

and cables batteries round consumable

blocks and other

consumables

121. Multimeter digital 05

122. Growler 01

123. Scientific Calculator 01

124. Hydrometer 02

125. Spray Gun (Painting) 500ml 01

126. Techometer 01

127. Valve Timing Diagram 01

128. Belt Tensioner Gauge 01

129. Portable electric drill Machine 01

130. Spring tension tester 01

C. General Installation/ Machineries

131. Carburetor repair kit 01

132. Hot patch clamp 01

1. Lathe general purpose all geared height

of center 150 mm to

below, Gap bed between centers

1000mm with all accessories

with all attachment

01

2. Drilling machine bench to drill up to

12mm dia along with

accessories

01

3. Cut section working model of Single

plate clutch assembly.

01

4. Cut section working model of

Diaphragm clutch assembly.

01

5. Cut section working model of

centrifugal clutch assembly.

01

6. Front axle ( Rzeeppa Joint) with stand

for Dismantling and

assembly

01

7. Rear axle with stand for Dismantling

and assembly

01

8. Constant Mesh Gear box with stand for

Dismantling and assembly.

01

9. Sliding mesh Gear box with stand for

Dismantling and assembly.

01

10. Synchronous Gear box with stand for

Dismantling and assembly.

01

11. Transfer case with stand for

Dismantling and assembly.

01

12. Cut section model of synchronous gear

box working

01

13. Cut section model of sliding mesh

gearbox working

01

14. Cut section model of constant mesh

gearbox working

01

15. Full floating axle and semi-floating

axle assembly

01

16. Cut section working model of

automatic transmission Gear box

01

17. Working model of fluid fly wheel 01

18. Working model of torque converter 01

19. Steering assembly -

1.Rack & pinion

2.Worm & roller

3. Recirculating ball

4.Power steering

01-each

20. Suspension and steering system trainer 01

21. Cut section models of shock absorbers 01

22. Stock absorber testing bench 01

23. Spring Tension scale – 0-4.5 kg. 01

24. Coil spring compressor for suspension

spring

01

25. Turbo charger , variable Turbo charger 01-each

26. Wheel alignment gauge – magnetic

type with turn tables

01

27. Wheel alignment setup instrument 01

28. Tyre changer 01

29. Nitrogen Tyre Inflation system 01

30. Tube vulcanizing machine 01

31. Tyre vulcanizing machine 01

32. Camber angle gauge 01-set

33. Toe-in, toe-out gauge 01-set

34. Wheel balancing machine with

accessory

01

35. Tubed tyre of cars 02-each

36. Tread wear indicator 01

37. Tyre & split rim wheel assembly 01

38. Solid tyre 01

39. Tubed tyre of car, trucks & motorcycle 01

40. Tubeless tyre of cars & trucks 01

41. Cut section of cross ply and radial tyres 01

42. Disk brake with caliper assembly 02

43. Drum brake assembly 01

44. Tandem master cylinder with booster 04

45. Wheel cylinder 04

46. Vacuum assisted hydraulics brake

assembly with vacuum booster

01

47. Air Brake Assembly 01

48. Brake Lining riveting machine (foot

operated)

01

49. Brake testing equipment (to test

efficiency of vehicle where

motion after braking is plotted)

01

50. Mechanical Hoist/Plate Form Type 01

51. Grinding machine (general purpose)

D.E. pedestal with 300 mm

dia wheels rough and smooth

01

52. A.C welding transformer 300 Amps

with complete accessories

02-sets

53. Oxy-acetylene welding equipment with

complete accessories

( Low & high pressure)

02

54. Spot welding machine with complete

accessories

01

55. Guillotine shearing Machine foot

operation

(1mt x 18G Capacity)

01

56. Fly press / Ball press No.4 single body 01

57. Pipe Bending Machine (Hydraulic

type) 12mm to 30mm

01

58. Spring tension tester 01

59. Bench lever shears 250mm Blade x

3mm Capacity

01

60. Gas Welding Table 1220mm x760mm 01

61. Hydraulic Trainer Kit –Basic along

with accessories

01

62. Pneumatic Trainer Kit- Basic along

with accessories

01

63. Electronic component trainer kit 01

64. Cylinder Block, CI Engine, Overhead

camshaft & camshaft in

block, air cooled

01-each

65. Carburetor – Solex, Mikuny for

dismantling and assembling

01-each

66. Carburetor repair tool kit 01

67. Demonstration board of 2W Ignition

system, ignition coil

01

68. Demonstration board of electronic

Ignition system, ignition coil

01

69. Spark Plug cleaning and testing

equipment

01

70. Starter motor axial type, pre-

engagement type & Coaxial

type

01 –each

71. Distributor –Duel advance type,

reluctance type

01-each

72. Tester sparking plug ‘NEON’ Type 01

73. Alternator assembly used for LMV 02

74. Starter motor assembly used for LMV 02

75. Electronic engine control module 01

76. Working Condition of Petrol MPFI

Engine Assembly with fault

simulation board

01

77. MPFI petrol engine with swiveling

stand along with special tools

for dismantling and assembling

01

78. Demonstration board of MPFI system 01

79. Ultrasonic Injection cleaning

equipment

01

80. Fuel feed pump 01

81. Multi-point fuel injection pump 01

82. Petrol nozzle 04

83. Air conditioning trainer kit 01

84. Air conditioning service Unit (Car) 01

85. Working Model of power windows 01

86. Petrol Engine(2-stroke) Motor

Cycle/Scooter along with special

tools and accessories

01

87. Cut model of 4 stroke Petrol engine on

stand

01

88. Cut model of 2 stroke Petrol engine on

stand

01

89. Mechanical Hoist/Plate Form Type 01

90. Multi scan tool /ECU diagnostics kit 01

91. Four stroke petrol engine with CNG 01

D. Workshop Furniture

setup-working condition

92. AC alternator slip ring puller 01

93. Functional/experiment model of

different type of sensors.

01-set

94. Executive Auto Electrical tool kit 01

95. Auto Electrical test bench 01

96. Cut section Model of Mock layout of a

motor car –electrical

system – working model

01-set

97. Car stereo 01

98. Battery 12V (Lead acid & Alkaline ) 02

99. Battery charger 6V – 24 V 02

100. Electrical horn ( different types ) 02

101. Wiper motor assembly 02

102. Anti theft device 02

103. Horn and Horn relay 02

104. Air conditioned MPFI vehicle with

accessories

01

105. 5 Point relays 02

106. 4 Point relays 02

107. Air bag simulator 01

108. Driving Simulator 01

109. Trolley type portable air compressor

single cylinder with 45

liters capacity Air tank, along with

accessories & with working

pressure 6.5 kg/sq cm

01

110. Grinding machine (general purpose) D.E. pedestal

with 300 mm

dia wheels rough and smooth

01

111. Tyer Changer Machine 01

1. Suitable Work Tables with vices 04

2. Discussion Table 01

3. Tool Cabinet 02

4. Fire Extinguishers, first- aid box 01-each

5. Book shelf (glass panel) 01

LIST OF TOOLS & Equipments for PLUMBER TRADE

6. Storage Rack 02

7. Storage shelf 02

8. LCD projector/ LED /LCD TV (big

size)

01

9. Multimedia CD for Automotive

application

05-of

different

softwares

10. Desktop computer and related MS

office software

06

11.

Computer Table

01

12.

Computer Chair

02

13. On Line UPS 2KVA 01

14. Laser Printer 01

1. Hammer Ball Peen 800 Gms 07

2. File flate rough 300mm 17

3. Sprit level wooden 300mm 10

4. Trovel 125 IS, 6013 17

5. Wooden malt small I.S.2022 17

6. Cutting Pliers 200 I S,3650 17

7. Steel tape(05 metre) 15

8. Rule Steel 300mm both in inch and

MM

15

9. Hacksaw frame Adjustable 250-300

mm

09

10. Chisel cold flate 20 mm 13

11. Hammer ball peen 50 grams 17

12. Travel C-125-is 6013 17

13. Stillson wranch 200 & 350 mm 07

14. Cutting Pliers-200-IS 3650 17

Tools, Measuring Instruments, Shop outfit and General Installation

LIST OF TOOLS & Equipments for PLUMBER TRADE

1. Surface Plate 400x400mm grade 01

2. Scribing block universal 300mm 02

3. File half round rough 100mm 02

4. File square rough 250 mm 02

5. Chisel cold flat 20x300mm 02

6. Chisel cross cut 6x150mmIS,402 02

7. Chisel round nose 3x150mm IS,402 02

8. Chisel diamond point 6x150mm 02

9. Punch letter set 3mm 1 set

10. Punch number set 1 set

11. Chase wedge 50mm 02

12. Dresser lead 350x50mm 02

13. Stick setting in 350x50mm 02

14. Saw plumber 300mm 02

15. Cutter, pipe wheel type 6mm to 25mm 02

16. Pipe jointer lead universal 01

1. Oil stone 150mmx50mmx25mm 02

2. Soldering iron, Copper fit fire heated,

hatched,straight 500gms

01-each

3. Try square 200mm 02

4. Tenon Saw 01

5. Hand Saw 01

LIST OF TOOLS & EQUIPMENT FOR WELDER

(Gas& Electric) SHOP OUTFIT (Starting from next page)

6. Mortice chisel 02

7. Firmer chisel 02

8. Mallet medium IS 2922 02

9. Pipe opener 01

10. Washer cutter 01

11. Splash stick 02

12. Sheet lead knife 02

13. Chipping knife 02

14. D.E. spanners

7x8,10x11,13x7,19x22,24x27 IS:2028

01 set

15. Plumber ladle 02

16. Plumbers metal melting pot 10kg 01

17. Tool caulking set of 2 02

18. Anvil 50 or 63 Kg, IS: 510 01

19. Pipe bender manually operated 01

20. Hand drill 6mm capacity with drill set 01

21. Drill twist(Straight shank) 3mm to

6mm

01-set

22. D.E Pedestal grinder with two wheels

175 rough and smooth

01

23. Bench drilling machine with chuk &

key up to 15 mm capacity

01

24. Double face hammers 01

25. PVC welding plant 01

26. Gas welding Set 01

27. Stillson wranch 450 & 520 mm 02-sets

28. Dormat and spade 01-each

29. File square smooth 02-Nos

30. File Trangular rough 250mm 02

31. File flat Rasp 250mm 02

32. File Trangular smooth 200mm 02

33. Stove melting solder 01

34. Googles pair welder 100mm 02-pairs

35. Flat smithy tong 02

36. Ratchet Brace with drill 6 to 25mm 01-set

37. Snip Straight 250mm & Snip Bend 02-each

List of Machinery for the welder trade

1. Gas welding Goggles with Colour

Glasses

13-

2. Safety boots for welders 13

3. Arc welding safety Goggles 13

4. Spindle Key 02

5. Letter punch 6mm 01-set

6. Spanner double ended 6mm -32mm 01-set

7. Clamps 10cm & 15cm 04

8. Steel Tape(05mtrs) flexible in case 01-set

9. Gas pressure regulator oxygen double

stage

02

10. Gas pressure regulator acetylene

double stage

02

11. First Aid Box 01

1. Welding Transformer with all

accessories 400,OCV 60-100,60% duty

cycle

01 set

2. Welding generator DC rotary set 200-

300 Amps with all accessories

01-set

3. Arc welding Rectifier set with all

accessories(400 A),OCV 60-100V-

60% Duty cycle

01-set

4. Pedestal Grinder fitted with coarse and

medium grain size, grinding wheel 300

mm Dia

02(sets)

5. Fire extinguisher foam & CO2 type 02(sets)

6. Oxygen & Acetylene cylinders 01-No

each

7. CO2 Arc welding Machine 400A-

Capacity with Air cooled with

regulator, wire coils & Inert Gas

01-set

8. A/c, DC TIG welding machine with 01-set

LIST OF TOOLS & Equipments for Draughtsman Civil TRADE

Survey Instruments

water cooled Torch 300 A, with Inert

Gas & all other Accessories

9. Bench Grinder fitted with fine grain

silicon carbide, grinding wheel 150mm

dia

01-set

10. Die penetrate testing kit 01-set

11. Arc welding table with positioners 06

12. Gas welding Table with suitable gas

welding fire bricks

06-sets

1. Box drawing instruments containing

one 15cm compass with pin point &

lengthening bar, one pair spring bows,

rotating compass with interchangeable

ink & pencil points, drawing pens with

plain point & cross point, screw driver

& box of leads.(0.2,0.3,0.4mm)

17

2. Weighting Triangle with tape

1250x900cms

02

3. Calculator Scientific 04

4. Print Trimmer Cutting edge 100cms 01

1. Land measuring chain 30meters with

10 arrows

04

2. Steel Tape 30 meters long

02

3. Ranging Rod wooden fitted

16

4. Optical Square PWD Pattern

04

List of Equipment and Furniture for Draughtsman Civil trade

5. Optical Square box type circular

01

6. Dumpy Level builder 25cm local

length X 23mm.Complete with Box &

accessories & stand

02

7. Levelling Staves 4 meters reading to

5mm telescopic type

1

Telescopic

2 set piece

8. Plain Table with stand & accessories

02 sets

9. Prismatic Compass with Stand.

02

1. Chest Of Drawers (Standard) 04 No.s

2. Personal Computer, Compatibility with

CAD (single user) with 17” colour

monitor

01 No.

3. CAD software (10 user licensed latest

version)

01 No.

4. Server 01 No.

5. Printer (A3 size) 01 No.

6. Plotter A0 (A-Zero) 01 No.

7. UPS 0.5 KVA 05 No.

8. Computer Table 05 No

9. Operator Chair 10 No

10. Printer Table 01 No.

11. Storage Cabnet 01 No.

12. Book Shelf 01 No.

LIST of Tools for Allied Trade used in construction Work (D.M Civil)

1. Shovel 02

2. Pan M.S 25cm dia 06

3. Farma wooden for measuring

aggregates

01

4. Bucket G.I 35CM DIA O4

5. Masons’s Plumb rule with Sprit level 04

6. Masons Square 30x30 cms 04

7. Sieve for sand 1mm/100x60 cm 01

8. Trowel 25cmx10cm 04

9. Sieve for sand 22mm/100x60 cm 01

10. Measuring Tape Steel 30 meters 04

11. Ladder Aluminum 3 meters 04

12. Pickaxe 02

13. Hammer 250gms 01

14. Crowbar 3cm dia.1.5 lag 02

15. Hand Hammer 1kg 02

16. Binoculars Latest version 02

17. Surveyor’s Umbrella 02

18. Light Tracing Board fitted with glass

and frame and lamp.

02