Installation SheetTANDBERG Edge

This box contains:TANDBERG Edge unit TANDBERG Precision HD cameraEdge unit wall mounting bracketPrecision HD camera bracketScrewdriver (PH2)Rubber feet and plug

Microphone and microphone cableHD camera cables, 2 m & 5 mLAN cableISDN cablesDVI-I to DVI-I cable (for monitor connection)DVI-I to VGA adapterS-Video cableRCA to RCA cableDVI-I to VGA cable with mini-jack to stereo RCA Audio cable (for PC connection)Audio cable, RCA to 2 × RCA2 × RCA to stereo mini-jack adapterCable sleeveCable tiesPower supply with cables

TANDBERG Remote Control and batteriesUser Guide on CDRegistration card

TANDBERGPrecisionHD Camera

The Camera must be installed properly by aligning the camera on the fixing bolt and the magnets on the camera bracket.*

PC

* Installation of the camera bracket with the TANDBERG Flat Panel Display Option.A wall mounted screen must have minimum 140 mm distance from the front of the screen to the wall.

LAN/Ethernet

Microphone

Monitor

Power Supply

Desktop Use

Touch tonesSnapshot

Camera Presets

TIPIf the menu is not already present, press the OK/Menu key on the remote control to open the menu. Navigate in the menu with arrow keys and OK.

Please read the user documentation for further details.

D13922.06 MARCH 2008

Using the unit out of the box

Placing the unit on a shelf

Put it on the desktop, connect cables as shown to the far right and it is ready to use.CAUTION! Never place the unit as shown without the base mounted!

Unscrew the base, using the enclosed screwdriver. Put the Edge codec on its back.

Turn the unit upside down and mount the rubber feet over the screws. Insert the rubber plug in the hole that held the screw just unscrewed.

Place the unit on the shelf.

1 2

3 4 Connect cables as shown to the right.

5

DVI-I to DVI-I

Composite

S-video

(optional)

CAUTION! Do not screw the screw back in if the base has been removed and the bracket is not to be used. Doing so may damage the codec’s interior and will void the warranty. Use the enclosed rubber plug instead.

Rubber plug

D1392205_Edge_Installation_Sheet_Feb08.indd 1 10.03.2008 09:56:24

Installation SheetTANDBERG Edge

Wall Mounting

Recommended mounting

DO NOT MOUNT IT HERE!

Alternative mounting

Alternative mounting

Equipment needed:

Caution!

Remove the monitor. Make sure there is space for all cables when the monitor is put back in place. Also make sure that the cable connections will be well hidden behind the monitor.

Recommended

Alt. 1

Alt. 2

Unscrew the base using the enclosed screwdriver.

Put the Edge codec on its back.

Bracket with screw (included).

Screwdriver to remove the base and mount the bracket (included).

Suitable screws (at least 4×15) to mount bracket on wall (not included). Each screw must be able to sustain at least 10 kg when bracket is mounted.

Screwdriver to mount bracket on wall (not included).

Decide where to mount the Edge codec.1 2 3

4 5 6

7 8Mount the Edge codec (with all the cables connected) onto the bracket using the screw of the wall bracket. Mount the monitor and camera (see instructions overleaf) back in place.

Hose (sleeve) to accommodate the cables between the codec and the monitor and camera (included).

Use screws in all four holes for mounting. Do not rely on the center hole alone.

Connect cables as shown overleaf.

D13922.06 MARCH 2008

Mount the bracket on the wall.

CAUTION! Never use other screws than the 20 mm screw already attached to the wall bracket. Do not remove this screw. Using other screws may damage the codec’s interior and will void the warranty.

D1392205_Edge_Installation_Sheet_Feb08.indd 2 10.03.2008 09:56:30