smc pneumatics fh hydraulic filters · fh how courtesy of steven engineering, inc.-230 ryan way,...

PageAccessory (Option)

414

418

422

426

430

433

437

— 441

Series FH�Hydraulic Filters

Series

Vertical Suction FilterSeries FHIA

Suction Filter with CaseSeries FH99

Suction GuardSeries FHG

Line FilterSeries FH34/44/54/64

Vertical Return FilterSeries FHBA

Return FilterSeries FH100

Oil FilterSeries FH150

Magnetic SeparatorSeries FHM

Operatingpressure

Negativepressure

Negativepressure

Negativepressure

Max.3.5, 7, 14,21 MPa

Max.1.6 MPa

Max.1 MPa

Max.1 MPa

—

Port size

1/2, 3/4, 1, 1 1/4, 1 1/2,2, 2 1/2, 3, 3 1/2, 4

1/2, 3/4, 1, 1 1/4, 1 1/2,2, 2 1/2, 3, 3 1/2, 4

1/2, 3/4, 1, 1 1/4, 1 1/2,2, 2 1/2, 3

3/8, 1/2, 3/4, 1, 1 1/41 1/2, 2, 2 1/2, 3

3/4, 1 1/4, 1 1/2

3/4, 1, 1 1/4, 1 1/2, 22 1/2, 3

1/4, 3/8, 1/2

—

Element (µm)nominal filtration

Micromesh74, 105, 149



Paper5, 10, 20

(Micromesh)

Paper5, 10, 20

Micromesh5, 10, 20

Paper5, 10, 20

Micromesh74, 105

Paper5, 10, 20

(Micromesh)

—

Differential pressure indicator (CB-��H)Differential pressure indication switch (CB-��H)Blanking cap





Differential pressure indicator (CB-��H)Differential pressure indication switch (CB-��H)Blanking capBracket

Differential pressure indicator (CB-��H)Differential pressure indication switch (CB-��H)Air breezerCap

413

FH�

HOW�

Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com

10 100 10001

10 -04

-06

-08

-10

-12

-16

-20

-24

-28

-30

These vertical suction filters are designed for installation between the pump and reservoir tank. Their main function is to protect the pump.

No air pocketsThere are no places for air pockets to form. This prevents damage to the pump and enables normal operation to start immediately.

Elimination of all collected matterAll collected matter can be disposed of reliably when the element is replaced. There is no dan-ger of collected matter dropping back into the tank.

No drain port requiredThe structure of the filter does not contain areas for drain fluid to collect, so there is no need to manually drain the pump.

Easy element replacementSimply open the cover to quickly replace the element without touching the pipes. The ele-ment is extracted from the top, so no fluid can leak out.

Compact and lightweightThe compact and lightweight design employs an aluminum casted housing.

Clogging sensorThe sensor indicates when the element is be-coming dirty, facilitating maintenance and help-ing to avoid pump damage such as cavitations.Differential pressure indicator/two-stage indica-tor, reset typeDifferential pressure indication switch/visual combined, non-reset type

Fluid

Operating pressure

Operating temperature

Main material

Element

Differential pressure indicator operating pressure

Relief valve open pressure

Hydraulic fluid

Negative pressure

Max. 80°CAluminum casting

NBR or FKM Note)

NBR or EPDM Note)

Micromesh

74, 105, 149 µm (200, 150, 100 mesh)

0.15 MPa

20.0 kPa

26.7 kPa

Cover/Case

O-ring

Seal

Material

Nominal filtration

Differential pressure resistance

Specifications

FHIA�-04FHIA�-06FHIA�-08FHIA�-10FHIA�-12FHIA�-16FHIA�-20FHIA�-24FHIA�-28FHIA�-32

1/2B

3/4B

1B

1 1/4B

1 1/2B

2B

2 1/2B

3B

3 1/2B

4B

30

50

95

150

220

350

550

770

1000

1300

Model Flange port size Note) Rated flow rate (l/min)

Model/Rated Flow Rate

RoHS

CB-56H

CB-56H-V

CB-57H

CB-57H-V

AG-12H

AG-12H-W

AG-12H-V

Petroleum, Water-glycol, Emulsion

Phosphoric ester


Phosphoric ester

Petroleum

Water-glycol, Emulsion

Phosphoric ester

Differential pressure indicator

Differential pressure indication switch(N.C. and N.O. common)

Blanking cap (for differential pressure indication part)

Description Part no. Note

Accessory/Option

Note) The material of the O-rings and seals differs depending on the hydraulic fluid used.Petroleum, Water-glycol, Emulsion: NBR; Phosphoric ester: FKM, EPDM

The symbol represented by � indicates the type of applicable hydraulic fluid. N: Petroleum, W: Water-glycol, Emulsion, V: Phosphoric esterNote) Fitted with companion flange. (Flange configuration is exclusive to SMC.)

Conditions Fluid: Turbine oil Class 2 VG56Viscosity: 45 mm2/sFilter material: MicromeshNominal filtration: 74 µm to 149 µm

Flow Characteristics

Pre

ssur

e dr

op (

kPa)

Flow rate (l/min)

414

Vertical Suction Filter

Series FHIA

RoHS-FHIA.qxd 10.7.26 6:11 PM Page 1


COM.

N.O.N.C.

View port G1/2

FH I A N 04 M M R074

Differential Pressure IndicationTwo indication methods are available: differen-tial pressure indicator and differential pressure indication switch. These can be mounted on all filter models.

� Differential pressure indicator• Operating pressure—20 kPa

• Once a value is displayed, it will continue to be displayed until reset, even if the pump is stopped. (2-stage display reset type)

• Perform element replacement when the red ring floats up and covers the entire view port.

� Differential pressure indication switch• Operating pressure—20 kPa

• When a value has been displayed, it will be automatically reset when the pump is stopped. (Non-reset type)

• This is a visual dual-purpose 2-stage display. Perform element replacement when the switch has actuated (when the red ring floats up and covers the entire view port).

• N.C. and N.O. common

How to Order

Hydraulic filter

I Suction

Model

A Vertical

Type

M Micromesh

Element

NWV

PetroleumWater-glycol, Emulsion

Phosphoric ester

Hydraulic fluid

04060810121620242832

1/2B

3/4B

1B

1 1/4B

1 1/2B

2B

2 1/2B

3B

3 1/2B

4B

Port size

MED

Differential pressure indicatorDifferential pressure indication switch Note)

None (Blanking cap)

Differential pressure indication

074105149

74 µm105 µm149 µm

Nominal filtration

RD

With relief valveNone (Blanking plate)

Relief valve

Note) Refer to page 444 for details.

Made to OrderNil

X0None (Standard)

Non-standard filtration

Note) N.C. and N.O. common

Replacement Element Part No.

Port size (Nominal size)

04 (1/2B)

06 (3/4B), 08 (1B)

10 (1 1/4B), 12 (1 1/2B)

16 (2B)

20 (2 1/2B), 24 (3B)

28 (3 1/2B), 32 (4B)

74 µm(200 mesh)

EM001H-074NEM101H-074NEM201H-074NEM301H-074NEM401H-074NEM501H-074N

105 µm(150 mesh)


149 µm(100 mesh)


Element size

ø65 x 90ø85 x 110

ø100 x 160ø120 x 180ø140 x 200ø180 x 260

Note 1) The symbol at the end of the element part no. indicates the hydraulic fluid type.N: Petroleum, Phosphoric ester, W: Water-glycol, Emulsion.

Note 2) Refer to page 444 for non-standard filtration.Note 3) Above elements require one element per filter.

Microswitch Rating

Ratedvoltage

Normallyclosed

Normallyopen

Resistance load

5 5 5 5 5 0.40.3

Non-inductive load (A) Inductive load (A)

125 AC250 AC8 DC14 DC30 DC125 DC250 DC

Normallyclosed

Normallyopen

Light load

1.51

0.70.5

Normallyclosed

Normallyopen

Inductive load

4 4

4 4 0.40.3

5 4

Normallyclosed

Normallyopen

Motor load

2.51.5

1.30.8

3 3 3 0.1 0.05

3 3 3 0.1 0.05

Precautions1. The figures in the above table indicate stationary

current. 2. An inductive load has a power factor (AC) of 0.75 or

more, and a time constant (DC) of 7 msec or less. 3. A light load has an inrush current 10 times greater.4. Lead wires are connected using a screw tightening

terminal.5. The electrical entry is equipped with a conduit

(G1/2) and grommet. 6. Please wire freely to the microswitch indication sym-

bol 1(COM.), 2(N.C.) and 3(N.O.).7. If a holding mechanism is necessary for the non-re-

set type, provide it using electric circuits.

(V)

Reset button

View port

415

Vertical Suction Filter Series FHIA

FH�

HOW�



Blanking cap

Hexagon socket head cap screw

Cover

Case

Relief valve

Spring washer

Element

r Base seal

e O-ring

e O-ring

q O-ring

w O-ring

Companion flange

Hexagon head boltINLET

OUTLET

Differential pressureindication switch

Differential pressure indication switch

Replacement Seal List (One each of the seal and O-ring types listed below are required per filter.)No.

DescriptionHydraulic fluid type

Petroleum,Emulsion,

Water-glycol

Phosphoric ester

Model

FHIA N -W

FHIA V-

0406081012162024283204060810121620242832

O-ring for cover case O-ring for elementStandard Standard

JIS B2401-1A-G70

JIS B2401-1A-G90

JIS B2401-1A-G105

JIS B2401-1A-G125

JIS B2401-1A-G145

JIS B2401-1A-G185

JIS B2401-4D-G70

JIS B2401-4D-G90

JIS B2401-4D-G105

JIS B2401-4D-G125

JIS B2401-4D-G145

JIS B2401-4D-G185

JIS B2401-1A-G35

JIS B2401-1A-G50

JIS B2401-1A-G65

JIS B2401-1A-G80

JIS B2401-1A-G100

JIS B2401-1A-G140

JIS B2401-4D-G35

JIS B2401-4D-G50

JIS B2401-4D-G65

JIS B2401-4D-G80

JIS B2401-4D-G100

JIS B2401-4D-G140

O-ring for companion flangeStandard

JIS B2401-1A-G30

JIS B2401-1A-G45

JIS B2401-1A-G55

JIS B2401-1A-G70

JIS B2401-1A-G95

JIS B2401-1A-G125

JIS B2401-4D-G30

JIS B2401-4D-G45

JIS B2401-4D-G55

JIS B2401-4D-G70

JIS B2401-4D-G95

JIS B2401-4D-G125

Element base sealPart no.

AL-196H

AL-197H

AL-198H

AL-199H

AL-200H

AL-201H

AL-196H-V

AL-197H-V

AL-198H-V

AL-199H-V

AL-200H-V

AL-201H-V

q Mounting

• Confirm INLET and OUTLET before connect-ing.

• For maintenance, make sure to provide suffi-cient space above the filter for removing the element.

w Operation

• Operation of the differential pressure indicator in cold weather, such as during winter, mostly occurs due to high viscosity, so check wheth-er it is from clogging or not after normal oper-ation starts.

• If the differential pressure indicator is the re-set type, make sure to reset it after normal operation starts in cold weather such as dur-ing winter.

• When using a differential pressure indication switch, if a filter clogged signal is incorpora-ted into the sequence circuit of the machine, make sure to design the system so the filter clogged signal does not operate until normal operation starts.

e Element replacement

• When the pressure difference reaches 20 kPa during filter operation (actuating the differen-tial pressure indicator), stop operation and either wash or replace the element.

• During disassembly and assembly, check that there is no cracking of or damage to the O-rings.

• When washing the element, do not wipe it us-ing a stiff brush or rag.

• After washing the element, make sure the base seal is properly mounted.

Handling Precautions

416

Series FHIA

Construction/Seal List


OUTLET

62

(65)

F


OUTLET

F

ø16

(34)


�B

øJ

øA4 x I

�G

INL

ET

OUTLET

C

DE

H

HF

Rem

oval

dim

ensi

on K

FHIA�-04FHIA�-06FHIA�-08FHIA�-10FHIA�-12FHIA�-16FHIA�-20FHIA�-24FHIA�-28FHIA�-32

Model

22.2

27.7

34.5

43.2

49.1

61.1

77.1

90.0

102.6

115.4

A 90

110

128

152

176

224

B 72

80

95

110

125

155

C116

133

185

214

220

280

D154

177

234

268.5

290.5

364.5

E38

44

49

54.5

70.5

84.5

F 60

70

86

100

120

150

G11

11

15

15

15

15

HM8 x 25

M8 x 25

M10 x 30

M12 x 35

M12 x 35

M16 x 40

I 56

70

86

102

130

166

J260

290

340

370

410

490

K 1.8

2.7

4.6

6.1

9.5

8.0

14.0

13.5

Mass (kg)

(mm)

417

Vertical Suction Filter Series FHIA

Dimensions

FH�

HOW�


Compact and lightweightThe compact and lightweight design employs an aluminum casted housing.

Prevents pump cavitationThe inlet size is larger than the outlet size to prevent pump cavitation.

Easy element maintenanceSimply open the cover to detach the element without touching the pipes.

Easy-mounting pipesThere is no mounting orientation, and two types are available: threaded and flange.

Accessories available for a variety of applicationsAvailable accessories include differential pres-sure indicators (differential pressure indicator or differential pressure indication switch), relief valves, and companion flanges.

Clogging sensorThe filter can be fitted with a differential pres-sure indicator (two-stage indicator, reset type) or differential pressure indication switch (visual combined, non-reset type).

FH990-04FH990-06FH990-08FH990-10FH990-12FH990-16FH991-20FH991-24FH991-28FH991-32

1/2B

3/4B

1B

1 1/4B

1 1/2B

2B

2 1/2B

3B

3 1/2B

4B

1B

1B

1 1/2B

1 1/2B

2B

2B

2 1/2B

3B

3 1/2B

4B

20

50

100

150

200

300

450

600

750

900

ModelPort size Note)

INLET OUTLETRated flow rate

(l/min)


Suction Filter with Case

Series FH99 RoHS

Fluid

Operating pressure


Main material

Element



Hydraulic fluid

Negative pressure

Max. 80°CAluminum casting

NBR or FKM Note)

NBR or EPDM Note)

Micromesh

74, 105, 149 µm (200, 150, 100 mesh)

0.2 MPa

24.0 kPa

33.3 kPa

Cover/Case

O-ring

Seal

Material

Nominal filtration


Specifications


Note) Both flange and threaded connections are supported. However, only flange types for FH991-20 to FH991-32 are compatible. The flange configuration is exclusive to SMC. Tapered threaded types (female) conforming to JIS B 0203.

CB-54H

CB-54H-V

CB-55H

CB-55H-V

AG-12H

AG-12H-W

AG-12H-V


Phosphoric ester


Phosphoric ester

Petroleum


Phosphoric ester





Accessory/Option

418

RoHS-FH99.qxd 10.7.26 6:11 PM Page 1


FH 9 04 0 0 090 M 074Hydraulic filter

Replacement Element Part No. (Including O-ring for element)

Model

FH990-04/06FH990-08/10FH990-12FH990-16FH991-20FH991-24FH991-28/32

74 µm(200 mesh)

With relief valve Without relief valve

EM520-074NEM620-074NEM720-074NEM820-074NEM920-074NEM030-074NEM130-074N

105 µm(150 mesh)


149 µm(100 mesh)


74 µm(200 mesh)


105 µm(150 mesh)


149 µm(100 mesh)


Element size

ø65 x 90ø82 x 133

ø104 x 177ø104 x 177ø132 x 212ø132 x 212ø155 x 193

9091

Common with L-type threaded and flangeL-type flange

Construction/Connection

04060810121620242832

1/2B

3/4B

1B

1 1/4B

1 1/2B

2B

2 1/2B

3B

3 1/2B

4B

Port size (Outlet side)

045

None



01

With relief valveNone

Relief valveHydraulic fluid

NilF

NoneWith companion flange

Companion flange

9 Negative pressure

Rated pressure

Made to Order

How to Order


Nil

X0None (Standard)

Non-standard filtrationNote) Refer to page 444 for details.

074105149

74 µm105 µm149 µm

Nominal filtration

M Micromesh

Element

012


Phosphoric ester

Note 1) The symbol at the end of the element part no. indicates the hydraulic fluid type.N: Petroleum, W: Water-glycol, Emulsion, V: Phosphoric ester



Differential pressure indicatorBlanking cap

Hexagon sockethead cap screw

Cover

Case

Relief valve

Elementr Seal (O-ring)

e Seal (O-ring)

q O-ring

w O-ring

Companion flange

INLET

OUTLET



No.Descrip-

tion Hydraulicfluid type

Petroleum,Emulsion,Water-glycol

Phosphoricester

Model

FH990-

FH991-

FH990-

FH991-

0406081012162024283204060810121620242832

q

JIS B2401-1A-P28

JIS B2401-1A-P42

JIS B2401-1A-P60

JIS B2401-1A-P90

JIS B2401-1A-P120

JIS B2401-1A-V120

JIS B2401-1A-V120

JIS B2401-4D-P28

JIS B2401-4D-P42

JIS B2401-4D-P60

JIS B2401-4D-P90

JIS B2401-4D-P120

JIS B2401-4D-V120

JIS B2401-4D-V120

w

O-ring forelement

Standard

JIS B2401-1A-V85

JIS B2401-1A-V100

JIS B2401-1A-V120

JIS B2401-1A-V150

JIS B2401-1A-V175

JIS B2401-4D-V85

JIS B2401-4D-V100

JIS B2401-4D-V120

JIS B2401-4D-V150

JIS B2401-4D-V175

O-ring forcover case

Standard

e

Seal for companion flange (O-ring)

Part no.

AL-130H

AL-133H

AL-135H

AL-136HAL-137H

AL-130H-V

AL-133H-V

AL-135H-V

AL-136H-VAL-137H-V

r

OUT sideIN sidePart no.AL-128HAL-129HAL-131HAL-132HAL-134HAL-135HAL-136HAL-137H

AL-128H-VAL-129H-VAL-131H-VAL-132H-VAL-134H-VAL-135H-VAL-136H-VAL-137H-V

Replacement Seal List (One each of the seal and O-ring types listed below are required per filter.)

419

Suction Filter with Case Series FH99

FH�

HOW�


Reset button

View portView port

COM.

N.O.N.C.

G1/2

Differential Pressure Indication

q Mounting

• Confirm INLET and OUTLET before connect-ing.

• For maintenance, make sure to provide suffi-cient space above the filter for removing the element.

w Operation


• If the differential pressure indicator is the re-set type, make sure to reset it after replacing the element or after normal operation starts in cold weather such as during winter.

• When using a differential pressure indication switch and if a filter clogged signal is incorpo-rated into the sequence circuit of the ma-chine, make sure to design the system so the filter clogged signal does not operate until normal operation starts.


• When the pressure difference reaches 24 kPa during filter operation (actuating the differen-tial pressure indicator), stop operation and either wash or replace the element.

• During disassembly and assembly, check that there is no cracking of or damage to the O-rings.

• When installing and removing an element, do not scratch or damage it by touching the cor-ners of the case, etc.



10 100 10001

10

-04

-06

-08 -1

0-1

2-1

6

-20

-24

-28/

32Conditions Fluid: Turbine oil Class 2 VG56

Viscosity: 45 mm2/sFilter material: MicromeshNominal filtration: 74 µm

Pre

ssur

e dr

op (

kPa)

Flow rate (l/min)

Two indication methods are available: differen-tial pressure indicator and differential pressure indication switch. These can be mounted on all filter models.





• When a value has been displayed, it will be automatically reset when the pump is stop-ped. (Non-reset type)










Microswitch Rating

Ratedvoltage

Normallyclosed

Normallyopen

Resistance load

5 5 5 5 5 0.40.3


125 AC250 AC8 DC14 DC30 DC125 DC250 DC

Normallyclosed

Normallyopen

Light load

1.51

0.70.5

Normallyclosed

Normallyopen

Inductive load

4 4

4 4 0.40.3

5 4

Normallyclosed

Normallyopen

Motor load

2.51.5

1.30.8

3 3 3 0.1 0.05

3 3 3 0.1 0.05

(V)

420


FH99�

Series FH99


L

A

M

V (Element removal dimension)

G

CD

I

øW

RS E

FU

QP

H

INL

ET

øX

N

OB

4 x K

U62

ø16

(65)

OUTLET



Differentialpressureindicator

(34)

OUTLET


U

Dimensions

Blanking cap

8 x T

INL

ET

OUTLET

4 x J


Model Threadedwithout flange With flange

6

8

10

10

5

S

M8 x 1.25Thread depth 8





T

84

91

103

118

133

U

180

240

300

360

340

V

35

50

62

77

90

102

115

W

23

28

35

44

50

62

X

2.4

3.6

5.4

9.7

10.6

Mass (kg)

3.4

5.0

7.8

13.5

14.4


Model

2 1/2B

3B

3 1/2B

4B

A1/2B

3/4B

1B

1 1/4B

1 1/2B

2B

1B

1 1/2B

2B

B

150

200

250

300

280

C

75

110

140

170

145

D

80

95

115

150

140

E

164

186

218

268

273

F

112

126

150

180

210

G

40

50

60

80

80

H

40

70

90

120

120

I




M16 x 2Thread depth 34


J

22.2

30.2

42.9

61.9

78

N

47.6

58.7

77.8

106.4

130

O

16.5

16.5

21.5

21.5

20

P

6

8

10

10

5

Q

16.5

16.5

21.5

21.5

20

R






K

52.4

69.9

77.8

106.4

130

L

26.2

35.7

42.9

61.9

78

M(mm)

Note) Both flange and thread connections are supported. However, only flange types for FH991-20 to FH991-32 are compatible. The flange configuration is exclusive to SMC. Tapered thread types (female) conforming to JIS B 0203.

421

Suction Filter with Case Series FH99

FH�

HOW�


Designed to prevent collected dust from falling into the tankAll collected dust can be disposed complete-ly when the element is replaced. There is no danger of collected matter dropping back into the tank.

No need to replace flushing oilSince all dust is eliminated during trial opera-tion, it is not necessary to replace flushing oil. This reduces both labor and wasted oil.

Easy maintenance and no air mixingNo special tools are required for mainte-nance, and insertion-type element replace-ment is quick and easy. This helps prevent air mixture into the suction line and pump damage.

Compact tank equipmentThe lubrication port strainer, suction filter, and air breather are all integrated into a sin-gle unit, reducing the volume of equipment around the tank.

Selection of connection methods and accessories for a variety of applica-tionsSix methods are available as standard. Dif-ferential pressure indicators (visual and switch) are available and can be selected to match the application.

PAT. PEND

Suction Guard

Series FHG RoHS

Fluid

Operating pressure


Main material

Element


Air breather nominal filtration

Lubrication port strainer nominal filtration

Hydraulic fluid

Negative pressure

Max. 80°CSteel plate

Steel plate

Steel plate

NBR or FKM Note)

NBR or EPDM Note)

Micromesh

74, 105, 149 µm (200, 150, 100 mesh)

0.2 MPa

24.0 kPa

40 µm

10 mesh or equivalent

Top flange

Case

Inlet pipe

O-ring

Seal

Material

Nominal filtration


Specifications

FHG9�A�-M�-04FHG9�A�-M�-06FHG9�A�-M�-08FHG9�B�-M�-10FHG9�B�-M�-12FHG9�B�-M�-16FHG9�C�-M�-20FHG9�C�-M�-24

1/2B

3/4B

1B

1 1/4B

1 1/2B

2B

2 1/2B

3B

18

32

53

90

120

200

315

450

Model Port sizeRated

flow rate


CB-21H

CB-21H-V

CB-67H

CB-67H-V

CW-4H

CW-4H-W

CW-4H-V

CW-5H

CW-5H-W

CW-5H-V

CW-6H

CW-6H-W

CW-6H-V

D-73H

D-73H-W

D-73H-V

D-74H

D-74H-W

D-74H-V

D-75H

D-75H-W

D-75H-V


Phosphoric ester


Phosphoric ester

Petroleum


Phosphoric ester

Petroleum


Phosphoric ester

Petroleum


Phosphoric ester

Petroleum


Phosphoric ester

Petroleum


Phosphoric ester

Petroleum


Phosphoric ester

For 1/2B to 1B

For 1 1/4B to 2B

For 2 1/2B, 3B

For 1/2B to 1B

For 1 1/4B to 2B

For 2 1/2B, 3B


Air breather

Cap



Accessory/Option

Connection


Female threaded connection ports are 1/2B to 2B only.Flange configuration is exclusive to SMC.

Companion flange,Female threaded companion flange,L-block companion flange,L-block female threaded companion flange, S-block companion flange,S-block female threaded companion flange

(l/min)

Note 1)

Note 2)

422

RoHS-FHG.qxd 10.7.26 6:11 PM Page 1


No.Descrip-

tionTop

flangeseal

Part no.

Hydraulicfluid type

Petroleum,Emulsion,

Water-glycol

Phosphoricester

Portsize

04

08AL-180H

AL-181H

AL-182H

AL-180H-V

AL-181H-V

AL-182H-V

10

16202404

0810

162024

O-ring forelement

Standard

JIS B2401-1A-G65

JIS B2401-1A-G85

JIS B2401-1A-G95

JIS B2401-4D-G65

JIS B2401-4D-G85

JIS B2401-4D-G95

JIS B2401-1A-P34

JIS B2401-1A-P60

—

—

JIS B2401-4D-P34

JIS B2401-4D-P60

Bottom caseO-ring for

suction pipeStandard

OUTconnection

sealPart no.

AL-183H

AL-184H

AL-185H

AL-183H-V

AL-184H-V

AL-185H-V

Seal forair breather/

capPart no.

AL-162H

AL-163H

AL-164H

AL-162H-V

AL-163H-V

AL-164H-V

FH G 9 0 A 04 0 0M 074Hydraulic filter

Suction guard


Port size (Nominal size)

04 (1/2B), 06 (3/4B), 08 (1B)

10 (1 1/4B), 12 (1 1/2B), 16 (2B)

20 (2 1/2B), 24 (3B)

74 µm(200 mesh)

EM220-074NEM320-074NEM420-074N

105 µm(150 mesh)

EM220-105NEM320-105NEM420-105N

149 µm(100 mesh)

EM220-149NEM320-149NEM420-149N

Element size

ø70 x 90ø90 x 125ø110 x 190

ABC

1/2B, 3/4B, 1B

1 1/4B, 1 1/2B, 2B

2 1/2B, 3B

Port size category

Port size(Nominal size)

Standard T dimension T dimensionwhen shippedSymbol Length

(mm)310380450520590385485585685560650750850

340410480550620430530630730560650750850

Adjustment range(mm)

±30

±45

Fixed

1234512341234

04 (1/2B)06 (3/4B)08 (1B)

10 (1 1/4B)12 (1 1/2B)16 (2B)

20 (2 1/2B)24 (3B)

Length below flange neck (T dimension)

∗ Standard T dimensions are excluded for 20 (2 1/2B), 24 (3B).

04 (1/2B), 06 (3/4B), 08 (1B) 10 (1 1/4B), 12 (1 1/2B), 16 (2B)

20 (2 1/2B), 24 (3B)

Port size (Nominal size) T dimension allowable range for symbol Z (mm)630 to 1,040740 to 1,130570 to 1,200

074105149

74 µm105 µm149 µm

Nominal filtration

0406081012162024

1/2B

3/4B

1B

1 1/4B

1 1/2B

2B

2 1/2B

3B

Port size

012345

Companion flangeFemale threaded companion flange

L-block companion flangeL-block female threaded companion flange

S-block companion flangeS-block female threaded companion flange

Connection

NilC

Air breatherCap

Air breather

Air breather t(cap)

Lubrication port strainer

Hexagon nut

Tension bolt

Element opening

Element w

Differential pressureindicator

r Seal

q Seat seal

e Suction pipe

Band

Case

How to Order

9 Negative pressure

Rated pressure

012


Phosphoric ester

Hydraulic fluid

015

None




Note) The symbol Z indicates lengths other than the standard T length and adjustment range. Specify the T length in this case.

Note) Refer to page 444 for details.

M Micromesh

Element

Note 1) The symbol at the end of the element part no. indicates the hydraulic fluid type.N: Petroleum, V: Phosphoric ester, W: Water-glycol, Emulsion.



/

/

to

to

to

to

Made to OrderNil

X0None (Standard)


(Max. T dimension)


423

Suction Guard Series FHG

FH�

HOW�



Two indication methods are available: differen-tial pressure indicator and differential pressure indication switch. These can be mounted on all filter models.Direct mounting is possible if the connection method is L-block or S-block. Otherwise, an Rc1 female thread fitting is required.In addition, if no differential pressure indication is required, use a commercially available plug (R1).


• Once a value is displayed, it will continue to be displayed until reset, even if the pump is stopped. (Reset type)

• The element should be replaced when the red indication is visible.



• The element should be replaced when the switch is actuated.




w Operation

• Operation of the differential pressure indicator in cold weather such as during winter mostly occurs due to high viscosity, so check wheth-er it is from clogging or not after normal oper-ation stars.

•Once the differential pressure indicator is trig-gered, the indication continues to be dis-played until the indicator is reset (by depress-ing the reset button), even if the pump stops operating.Reset after replacing the element and restart-ing operation, or after normal operation starts in cold weather such as during winter.



• When the pressure difference reaches 24 kPa during filter operation (triggering the differen-tial pressure indicator), stop operation and either wash or replace the element.

• When replacing the element, check the O-rings and replace them if they are damaged.



r Removing the element

• Rotate the air breather (cap) one-third of a turn counterclockwise and remove it. Grasp the handle of the lubrication port strainer in-side and, while rotating it clockwise, pull it up vertically. The suction element is screwed onto one end of the tension bolt and along with the lubrication port strainer, can be removed and installed freely. Do not remove the suction ele-ment while the pump is operating.

t T dimension (length below flange neck) adjustment

• The product is shipped from the factory with the maximum T dimension, so the user must adjust it to the required T dimension.

• The T dimension adjustment range, relative to the standard T dimension, is ±30 mm for 1/2B to 1B and ±45 mm for 1 1/4B to 2B. The dimension for 2 1/2B to 3B is fixed, so no ad-justment is possible.

• Refer to the operating manual for details of the adjustment method.

y Lubrication

• Remove the air breather (cap) and lubricate through the lubricatioin port strainer. Be care-ful not to let oil, etc., get onto the cap while it is being removed.


q Mounting

• The portion of the suction guard below the oil tank mounting flange is installed inside the oil tank, so check to make sure it is clean when mounting it. For maintenance, make sure to provide sufficient space above the filter for re-moving the element.

• Use caution to ensure airtightness when con-necting an outlet and installing a differential pressure indicator (especially for the thread type).

• Ensure that the oil tank fluid volume (mini-mum fluid level MIN(r) dimension) is 30 mm for 1/2B to 1B, 60 mm for 1 1/4B to 1 1/2B, 80 mm for 2B, and 120 mm or more for 2 1/2B to 3B, measured when there is no turbulence in the flow from the element open-ing or fluctuation in the fluid level. Also, select a T dimension (length below flange neck) that will ensure that the fluid level does not reach the lubrication port strainer.


Conditions Fluid: Turbine oil Class 2 VG32Viscosity: 45 mm2/sFilter material: MicromeshNominal filtration: 74 µm

Series FHG

10 100 10001

10

Pre

ssur

e dr

op (

kPa)

Flow rate (l/min)








Microswitch Rating

Ratedvoltage

Normallyclosed

Normallyopen

Resistance load

5 5 5 5 5 0.40.3


125 AC250 AC8 DC14 DC30 DC125 DC250 DC

Normallyclosed

Normallyopen

Light load

1.51

0.70.5

Normallyclosed

Normallyopen

Inductive load

4 4

4 4 0.40.3

5 4

Normallyclosed

Normallyopen

Motor load

2.51.5

1.30.8

3 3 3 0.1 0.05

3 3 3 0.1 0.05

(V)

Reset button

COM.

N.O.N.C.

G1/2

-04/

06/0

8

-10/

12/1

6-2

0/24

424

Series FHG


Body mounting dimension

4 x M8I

H

ACA

DWindowfor removal

Ele

men

t rem

oval

dim

ensi

on T

+10

0B H

AI10

10

C M D

L


Seat seal

Minimumfluid level

Element

T(V

)(S

)

(U)

MIN

(r)

AG

F

IDøG

(65)

Cap

Body mounting dimension

6 x M8135 170

H

AC

ADWindow

for removal

Ele

men

t rem

oval

dim

ensi

on T

+10

0Element

B H

A135 17010

10

C

M

D

6 x ø10

L

Air breather

Minimumfluid levelT

(V)

(S)

(U)

MIN

(r)

AG

F

IDøG

(65)

L-type block

P Q

NY

ød

Z

E (Rc)

W

RP Q

J

ødS-type block

W

K AE

Y

ød

G

Y

Port size: 20, 24Port size: 04 to 16

Dimensions

4 x ø10

Air breather


Seat seal

Cap

Port size(Nominal size)

T dimension adjustment rangeA B C D F G H I L M S U V r AC AD AG

1 2 3 4 5Standard T dimension

215215215265265265325325

130130130150150150190190

6565657575758585

90 90 90115115115145145

66666688

72 72 72 86 86 86106106

110110110130130130170170

195195195245245245——

1919191919192020

1010101010102020

6363636363637676

1414141717171717

90 90 90126126126197197

30 30 30 60 60 80120120

177177177227227227285285

110110110130130130150150

120120120140140140170170

310

385

560

380

485

650

450

585

750

520

685

850

590

—

—

±30

±45

Fixed

1/2B (04)3/4B (06)

1B (08)1 1/4B (10)1 1/2B (12)

2B (16)2 1/2B (20)

3B (24)

(mm)

Connection part dimensions/Companion flange

Female threaded companion flange L-type block companion flange

(75)

(50)



1/2B (04)3/4B (06)

1B (08)1 1/4B (10)1 1/2B (12)

2B (16)2 1/2B (20)

3B (24)

22.227.734.543.949.161.177.190.0

2.7 2.7 2.7 5.1 5.1 5.010.310.3

Port size Mass (kg)*d2525252828282828

G99999999

Y(mm)

1/2B (04)3/4B (06)

1B (08)1 1/4B (10)1 1/2B (12)

2B (16)

1/23/41

1 1/41 1/2

2

Port size Mass (kg)*E474752585863

Z2.82.82.85.35.35.4

(mm)

1/2B (04)3/4B (06)

1B (08)1 1/4B (10)1 1/2B (12)

2B (16)2 1/2B (20)

3B (24)

22.227.734.543.949.161.177.190.0

56 56 56 76 76 76101101

71 71 71104104104129129

5353537474749494

99999999

3.6 3.6 3.6 7.3 7.3 7.114.514.5

Port size Mass (kg)*d N P Q Y(mm)

1/2B (04)3/4B (06)

1B (08)1 1/4B (10)1 1/2B (12)

2B (16)

1/23/41

1 1/41 1/2

2

78 78 83106106111

71 71 71104104104

535353747474

3.73.73.77.47.47.5

Port size Mass (kg)*E J P Q

∗ Weight values are for the minimum T dimension (symbol 1) in each standard T dimension.∗ The “OUT” direction can be mounted up to 90° to the left or right.

∗ Weight values are for the minimum T dimension (symbol 1) in each standard T dimension.∗ The differential pressure indication entry can be mounted up to 90° to the left or right.

∗ Weight values are for the minimum T dimension (symbol 1) in each standard T dimension.∗ The differential pressure indication entry can be mounted up to 90° to the left or right.

∗ Weight values are for the minimum T dimension (symbol 1) in each standard T dimension.

∗ Weight values are for the minimum T dimension (symbol 1) in each standard T dimension.

∗ Weight values are for the minimum T dimension (symbol 1) in each standard T dimension.∗ The “OUT” direction can be mounted up to 90° to the left or right.

L-type block

(75)

(50) E (Rc)



L-type block female threaded companion flange



(75)(50)

S-type block companion flange

(75)(50)

E (Rc) S-type block Differential pressure indication switch


S-type block female threaded companion flange

1/2B (04)3/4B (06)

1B (08)1 1/4B (10)1 1/2B (12)

2B (16)

1/23/41

1 1/41 1/2

2

3.63.63.66.46.46.5

Port size Mass (kg)*E696974808085

R707070858585

W(mm)1/2B (04)

3/4B (06)1B (08)

1 1/4B (10)1 1/2B (12)

2B (16)2 1/2B (20)

3B (24)

22.227.734.543.949.161.177.190.0

4747475050505050

70 70 70 85 85 85105105

99999999

6262626565656565

3.5 3.5 3.5 6.2 6.2 6.111.911.9

Port size Mass (kg)*d K W Y AE(mm)

425

Suction Guard Series FHG

FH�

HOW�


Compact, solid, and safe designThe case and cover have undergone testing in which they were subjected 100,000 times to impacts equivalent 1.5 times the rated pressure (confirming to MIL standard).

Easy element replacementThe element is extracted from the top, and secured in place by inserting an O-ring seal. The element can be installed and removed easily, simplifying maintenance.

Reliable outlet sideA firm seal is secured through a special con-figuration combining a pressure clamp from an O-ring around the inner perimeter of the case with support from the cover, and there is no resistance when the cover is installed and removed.

Large drain exhaust portThe large M24 drain exhaust port assures rapid drainage.

Easy fluid flow direction reversalSimply turn the cover 180° relative to the case mounting base to reverse the fluid flow direction.

Clogging sensorThe filter can be mounted with a differential pressure indicator (two-stage indicator, reset type) or differential pressure indication switch (common with visual, non-reset type).

Line Filter

Rated Pressure: 3.5, 7, 14, 21 MPaSeries FH34/44/54/64

RoHS

Fluid

Operating pressure


Main material

Element



Hydraulic fluid

Max. 80°C

NBR or FKM Note)

Paper

5, 10, 20 µm

0.6 MPa

0.275 MPa

0.35 MPa

Max. 3.5 MPa

Aluminum die-cast (3/8, 1/2, 3/4, 1)

Aluminum casted (1 1/4, 1 1/2, 2)

Max. 7, 14, 21 MPa

Cast iron

O-ring

Material

Nominal filtration


Cover/Case

Specifications

CB-48H

CB-48H-V

CB-52H

CB-52H-V

CB-64H

CB-64H-V

CB-49H

CB-49H-V

CB-53H

CB-53H-V

CB-65H

CB-65H-V

AG-9H

AG-9H-W

AG-9H-V

AG-12H

AG-12H-W

AG-12H-V

FH342

FH342

FH342


Phosphoric ester


Phosphoric ester


Phosphoric ester


Phosphoric ester


Phosphoric ester


Phosphoric ester

Petroleum


Phosphoric ester

Petroleum


Phosphoric ester


Differential pressure indication switch (N.C. and N.O. common)


Description Part no. Model Note

Accessory/Option

FH34

FH44

01

01

FH54

FH64

01

01

FH34

FH44

01

01

FH54

FH64

01

01

FH34

FH64

01

01

FH340-03FH340-04FH342-06FH342-08FH340-10FH340-12

—

FH440-03FH440-04FH440-06FH440-08FH440-10FH440-12

—

—

—

—

—

FH341-06FH341-08FH341-10FH341-12FH341-16

—

FH441-04FH441-06FH441-08FH441-10FH441-12FH441-16FH441-20FH441-24

—

—

20 (3/4B)

25 (1B)

32 (1 1/4B)

40 (1 1/2B)

50 (2B)

—

15 (1/2B)

20 (3/4B)

25 (1B)

32 (1 1/4B)

40 (1 1/2B)

50 (2B)

65 (2 1/2B)

80 (3B)

3/8

1/2

3/4

1

1 1/4

1 1/2

—

3/8

1/2

3/4

1

1 1/4

1 1/2

—

—

—

10

20

50

80

120

160

260

10

20

50

80

120

160

260

450

600

Max.3.5

MPa

Max.7

MPa

Operatingpressure

Port size Ratedflow rate

Model


Threadedconnection Flange connection Threaded

Rc Flange SSA

FH540-03FH540-04FH540-06FH540-08FH540-10FH540-12

—

FH640-03FH640-04FH640-06FH640-08FH640-10FH640-12

—

—

FH541-04FH541-06FH541-08FH541-10FH541-12FH541-16

—

FH641-04FH641-06FH641-08FH641-10FH641-12FH641-16

—

15 (1/2B)

20 (3/4B)

25 (1B)

32 (1 1/4B)

40 (1 1/2B)

50 (2B)

—

15 (1/2B)

20 (3/4B)

25 (1B)

32 (1 1/4B)

40 (1 1/2B)

50 (2B)

3/8

1/2

3/4

1

1 1/4

1 1/2

—

3/8

1/2

3/4

1

1 1/4

1 1/2

—

10

20

50

80

120

160

260

10

20

50

80

120

160

260

Max.14

MPa

Max.21

MPa

ModelThreadedconnection Flange connection

Note) Tapered female thread connection conforming to JIS B 0203 is compatible. Flanges conforming to JIS B 2291 (21 MPa piping flanges for hydraulic use) SSA are compatible.

Port sizeThreaded

Rc Flange SSA

Note) The material of the O-rings and seals differs depending on the hydraulic fluid used. Petroleum, Water-glycol, Emulsion: NBR; Phosphoric ester: FKM

to

to

to

to

to

(l/min)

Ratedflow rate(l/min)

Operatingpressure

426



Replacement Element Part No. (Including O-ring for element)Port size

03 (3/8), 04 (1/2)

06 (3/4), 08 (1)

10 (1 1/4), 12 (1 1/2)

16 (2)

20 (2 1/2), 24 (3)

5 µmEP910-005NEP020-005NEP120-005NEP220-005NEP820-005N



Element sizeø53 x 90

ø74 x 117ø74 x 195ø88 x 282

ø119 x 280

Note 1) The symbol at the end of the element part no. indicates the hydraulic fluid type. N: Petroleum, V: Phosphoric ester, W: Water-glycol, Emulsion (10 µm only)


FH 033 40 0 0 0 P 005Hydraulic filter

3456

3.5 MPa 7 MPa 14 MPa 21 MPa

Operating pressure (Max.)

01


Relief valve Hydraulic fluid012


Phosphoric ester

005010020

5 µm10 µm20 µm

Nominalfiltration

PM

PaperMicromesh

Element

L

4042∗

41

Threaded

Flange


∗ Indicates 42 for 3.5 MPa, Port si-zes 3/4 and 1.

0124 5

NoneDifferential pressure indicator

Differential pressure indication switch Note)


Differential pressureindication

LNil IN left

IN right

Fluid direction

Symbol

030406081012162024

Threaded Rc3/81/23/41

1 1/41 1/2

———

Flange SSA—

15 (1/2B)

20 (3/4B)

25 (1B)

32 (1 1/4B)

40 (1 1/2B)

50 (2B)

65 (2 1/2B)

80 (3B)

Port size

Note) For selection from thread and flange, refer to “Model/Rated Flow Rate” on page 426.

How to Order

Note) The non-standard filtration rating is for micromesh ele-ments only. Refer to page 444 for details.

Note) For water-glycol oremulsion: only 10 µm.Note) N.C. and N.O. common

Construction 42 only

Made to OrderNilX0

None (Standard)Non-standard filtration

Element upwardremoval

Element upward removal

Blanking capHexagon socket head cap screw

Cover

Case

Element

r O-ring

e O-ring

q O-ring

w O-ring

Drain plug

INLET


DRAIN

OUTLET

Differentialpressureindicator

Relief valve


No.Descrip-



Phosphoricester

Model

FH340

FH34�

FH441

FH340

FH34�

FH441

-03-04-06-08-03

-04-06-08-10-12

-16

-20-24-03-04-06-08-03

-04-06-08-10-12

-16

-20-24

JIS B2401-1A-P30

JIS B2401-1A-P44

JIS B2401-1A-P30

JIS B2401-1A-P44

JIS B2401-1B-P28

JIS B2401-1A-P50

JIS B2401-1A-P85

JIS B2401-4D-P30

JIS B2401-4D-P44

JIS B2401-4D-P30

JIS B2401-4D-P44

JIS B2401-4D-P50

JIS B2401-4D-P85

JIS B2401-4D-P28

O-ring forelement

Standard

JIS B2401-1B-G80

JIS B2401-1B-G105

JIS B2401-1B-G65

JIS B2401-1B-G90

JIS B2401-1B-G105

JIS B2401-1B-G145

JIS B2401G80FPM/Hs = 90







O-ring forelement

O-ring forOUT side

Standard Standard Standard

FH44�FH64�

FH440FH640FH44�FH64�

FH440FH640FH44�FH64�

FH34�FH64�FH341

FH641

FH44�FH64�FH34�FH64�FH341

FH641

JIS B2401-1A-P22A

JIS B2401-1A-P32

JIS B2401-1A-P20

JIS B2401-1A-P32

JIS B2401-1A-P40

JIS B2401-1A-P50

JIS B2401-1A-P85

JIS B2401-4D-P22A

JIS B2401-4D-P32

JIS B2401-4D-P32

JIS B2401-4D-P40

JIS B2401-4D-P50

JIS B2401-4D-P85

JIS B2401-4D-P20

Line Filter Series FH34/44/54/64


to

to

to

to

to

to

to

to

to

to

Replacement Seal List (One each of the O-ring types listed below are required per filter.)

427

FH�

HOW�


Reset button

View port

COM.N.O.N.C.

View port G1/2

� Differential pressure indication switch• Operating pressure—0.275 MPa











q Mounting• Confirm INLET and OUTLET before mount-

ing. Then connect so that the drain is orien-ted downward. For maintenance, make sure to provide sufficient space above the filter for removing the element.

w Operation

• Operation of the differential pressure indicator in cold weather such as during winter mostly occurs due to high viscosity, so check wheth-er it is from clogging or not after normal oper-ation starts.

•Once the differential pressure indicator is ac-tuated, the indication continues to be dis-played until the indicator is reset (by depress-ing the reset button), even if the pump stops operating.Reset after replacing the element and restart-ing operation, or after normal operation starts in cold weather such as during winter.



• When the pressure difference reaches 0.275 MPa during operation (actuating the differen-tial pressure indicator), stop operation, drain the oil from the case, and replace the element.



r Others

• For the top cover O-ring, use a product of hardness 90 to prevent leaks or damage.

• If there is back pressure, install a check valve on the outlet side to prevent damage to the element.

• Turn the top cover 180° to reverse the oil flow direction.

• Use an auxiliary pipe or the like and apply force evenly when tightening the cap screws on the cover and case.


0.15

0.1

0.05

0.04

0.03

0.02

0.01

Pre

ssur

e dr

op (

MP

a)

10 30 50 100 300 500

Series FH34/44

0.1

0.050.04

0.03

0.02

0.01

0.005

0.003

5 10 30 50 100 300

0.1

0.050.04

0.03

0.02

0.01

5 10

Pre

ssur

e dr

op (

MP

a)

Flow rate (l/min)

Conditions Fluid: Turbine oil Class 2 VG56Measured pressure: 14 MPaViscosity: 45 mm2/sFilter material: PaperNominal filtration: 10 µm

Series FH54

30 50 100 300


Flow rate (l/min)

Conditions Fluid: Turbine oil Class 2 VG56Measured pressure: 3.5, 7 MPaViscosity: 45 mm2/sFilter material: PaperNominal filtration: 10 µm

03/0

4

10/1

2

20/2

416

06/0

8

03/0

4

06/0

8 10/1

2

16

Pre

ssur

e dr

op (

MP

a)

Flow rate (l/min)


Series FH64

10/1

2

03/0

4

06/0

8

16


� Differential pressure indicator• Operating pressure—0.275 MPa




Microswitch Rating

Ratedvoltage

(V) Normallyclosed

Normallyopen

Resistance load

5 5 5 5 5 0.40.3


125 AC250 AC8 DC14 DC30 DC125 DC250 DC

Normallyclosed

Normallyopen

Light load

1.51

0.70.5

Normallyclosed

Normallyopen

Inductive load

4 4

4 4 0.40.3

5 4

Normallyclosed

Normallyopen

Motor load

2.51.5

1.30.8

3 3 3 0.1 0.05

3 3 3 0.1 0.05

428

Series FH34/44/54/64


D

A

C�

B

X X'

F (

Ele

men

t rem

oval

dim

ensi

on)

INLET

2 x d

Blanking cap

OUTLET

GE

H

X X'

JJ'

D

D

JG

OUTLET

G

Dimensions

øM (Drill)

�P

4 x N depth Q

Comparison flange base

DRAIN

(∗): Internal dimensions for FH342 type


OUTLET


INLET

( 30)

( 34∗

)INLET

2 x K depth L

X X'

Bracket mounting baseport size 03 to 08

4 x K depth L

Bracket mounting baseport size 10 to 24



( 60)

( 65∗

)

Portsize

04

06

08

10

12

16

2024

Model

FH441FH541FH641FH341FH441FH541FH641FH341FH441FH541FH641FH341FH441FH541FH641FH341FH441FH541FH641FH341FH441FH541FH641FH441FH441

Bolt dimension

M10 x 1.5 x 30

M10 x 1.5 x 40

M10 x 1.5 x 30

M10 x 1.5 x 40

M12 x 1.75 x 40

M12 x 1.75 x 45

M12 x 1.75 x 40

M12 x 1.75 x 45

M16 x 2 x 50

M16 x 2 x 60

M16 x 2 x 50

M16 x 2 x 60M20 x 2.5 x 65M22 x 2.5 x 65

SSA15

SSA20

SSA25

SSA32

SSA40

SSA50

SSA65SSA80

G25

G30

G35

G40

G50

G60

G75G85

Note) The companion flange mounting base conforms to JIS B 2291 (21 MPa pipe flanges for hydraulic use) SSA.

Companion Flange Bolt Dimensions

Flange(JIS B2291)

O-ring(JIS B240-1-A)

FH340-03FH340-04FH342-06FH342-08FH341-06FH341-08FH34 -10FH34 -12FH341-16FH440-03FH44 -04FH44 -06FH44 -08FH44 -10FH44 -12FH441-16FH441-20FH441-24FH540-03FH54 -04FH54 -06FH54 -08FH54 -10FH54 -12FH541-16FH640-03FH64 -04FH64 -06FH64 -08FH64 -10FH64 -12FH641-16

0101

0101010101

0101010101

0101010101

————

20 (3/4B)

25 (1B)

32 (1 1/4B)

40 (1 1/2B)

50 (2B)—

15 (1/2B)

20 (3/4B)

25 (1B)

32 (1 1/4B)

40 (1 1/2B)

50 (2B)

65 (2 1/2B)

80 (3B)—

15 (1/2B)

20 (3/4B)

25 (1B)

32 (1 1/4B)

40 (1 1/2B)

50 (2B)—

15 (1/2B)

20 (3/4B)

25 (1B)

32 (1 1/4B)

40 (1 1/2B)

50 (2B)

3/81/23/41——

1 1/41 1/2

—

3/81/23/41

1 1/41 1/2

———

3/81/23/41

1 1/41 1/2

—

3/81/23/41

1 1/41 1/2

—

105

136

141

150

155

100

135

150

160

220

105

145

150

180

120

155

180

200

96

120

120

106

120

80

105

105

120

170

86

108

108

126

98

124

124

144

50

65

63

56

70

45

57

57

65

100

45

56

56

70

51

65

65

75

80

60

100

100

120

60

80

80

92

130

70

100

100

120

90

120

125

145

160.5

180

199.5

260

361

152

182

260

359

390

152

182

260

361

152

182

260

361

275

340

330

435

545

285

330

435

540

615

285

330

435

545

285

330

435

545

57

61

69

87

94

62

73

87

94

119

62

73

87

94

62

73

87

94

217.5

241

268.5

347

455

214

255

347

453

509

214

255

347

455

214

255

347

455

5

0

0

50

60

0

0

50

60

40

0

0

50

60

0

0

50

60

—

—

—

0

0

—

—

0

0

25

—

—

0

0

—

—

0

0

2 x M8 x 1.25

2 x M10 x 1.5

2 x M10 x 1.5

4 x M10 x 1.5

4 x M12 x 1.75

2 x M8 x 1.25

2 x M10 x 1.5

4 x M10 x 1.5

4 x M12 x 1.75

4 x M12 x 1.75

2 x M8 x 1.25

2 x M10 x 1.5

4 x M12 x 1.75

4 x M12 x 1.75

2 x M10 x 1.5

2 x M10 x 1.5

4 x M12 x 1.75

4 x M12 x 1.75

19

15

23

23

28

14

18

18

22

22

14

18

22

22

18

18

22

22

—

—

2025323646—

1620253236466070—

162025323646—

162025323646

—

—

4 x M10 x 1.54 x M12 x 1.754 x M12 x 1.754 x M16 x 24 x M16 x 2 —4 x M10 x 1.54 x M10 x 1.54 x M12 x 1.754 x M12 x 1.754 x M16 x 24 x M16 x 24 x M20 x 2.54 x M22 x 2.5 —4 x M10 x 1.54 x M10 x 1.54 x M12 x 1.754 x M12 x 1.754 x M16 x 24 x M16 x 2 —4 x M10 x 1.54 x M10 x 1.54 x M12 x 1.754 x M12 x 1.754 x M16 x 24 x M16 x 2

—

—

40 48 56 65 73—

36 40 48 56 65 73 92103—

36 40 48 56 65 73—

36 40 48 56 65 73

—

—

1217172020—

1212171720202727—

121217172020—

222222223030

1.8

2.5

3.5

4.6

6.4

4.5

8.7

12.2

18.1

35.9

5.2

9.7

12.8

20.4

6.9

12.9

19.8

29

ModelMass(kg)

d A B C D E F G H J J' K L M N P Q

(mm)

Threaded Rc Flange SSA

Note) Tapered female thread conforming to JIS B 0203 is compatible.Flanges conforming to JIS B 2291 (21 MPa pipe flanges for hydraulic use) SSA are compatible.

429

Line Filter Series FH34/44/54/64

FH�

HOW�


Pressurecontrolvalve

Pump

Vertical return filter

Oil tank

M

Machine

Compact design that does not clutter the top of the oil tankSince most of the filter case is inside the oil tank, very little space is occupied on the top of the tank.

No need for an OUTLET pipeThe filter case also functions as a fluid return pipe, so there is no need to attach a separate OUTLET pipe.

Easy maintenanceSimply open the cover and extract the element from the top of the filter. Replacement is quick and easy.

Designed to prevent collected dust from falling into the oil tankThe collected dust remains inside the element, so it cannot flow out when the relief valve is opened and all collected dust is removed from the case.

Two INLET portsThe filter has two INLET ports, oriented 180° from each other to provide more flexibility when routing pipes.

0.1

0.05

0.03

0.01

0.005

0.001100 30 50 100 300 500

06 10 12

Vertical Return Filter

Series FHBA RoHS

The vertical return filters are designed for mounting directly on top of oil tanks for hydraulic systems. They prevent dust generated within the circuit from entering the tank and help keep the oil clean. This efficient configuration reduces the total number of filters required.

Operating pressure


Main material

Element



Max. 1.6 MPa

Max. 80°CAluminum die-cast

Aluminum die-cast

Steel plate

NBR or FKM Note)

Paper and micromesh

5, 10, 20 µm

0.6 MPa

0.18 MPa

0.25 MPa

Cover

Body

Case

O-ring/Seal

Material

Nominal filtration ∗


Specifications

∗ Micromesh elements with other than the standard filtration are available. ∗ The paper elements for water-glycol is 10 µm only.Note) The material of the O-rings differs depending on the hydraulic fluid used.

Petroleum, Water-glycol, Emulsion: NBR; Phosphoric ester: FKM

FHBA�-06FHBA�-10FHBA�-12

3/4

1 1/4

1 1/2

N : PetroleumW: Water-glycol

EmulsionV : Phosphoric ester

Model

The symbol represented by � indicates the type of applicable hydraulic fluid (N, W, V).

Port size (Rc)

150

300

400

Max. flow rate (l/min)

1.7

3.7

5

Mass (kg) Applicable hydraulic fluid


CB-58H

CB-58H-V

CB-59H

CB-59H-V

AG-12H

AG-12H-W

AG-12H-V


Phosphoric ester


Phosphoric ester

Petroleum


Phosphoric ester





Accessory/Option


Pre

ssur

e dr

op (

MP

a)

Flow rate (l/min)

Conditions Fluid: Turbine oil Class 2 VG56Measured pressure: 1.6 MPaViscosity: 45 mm2/sFilter material: PaperNominal filtration: 10 µm

430

RoHS-FHBA.qxd 10.7.26 6:12 PM Page 1


q Mounting

• Confirm the INLET orientation before mounting. Then connect so that the case is oriented down-ward. For maintenance, make sure to provide sufficient space above the filter for removing the element.

• The filter has two INLET ports. If one is not used, it must be covered with a plug or the like.

• Before mounting the filter on the oil tank, confirm that r the O-ring (see “Construction”) is installed on the body.

• Ensure that the opening in the case (OUTLET) is always below the fluid surface. Air could leak into the system if the fluid level drops below the out-let opening.

w Operation

• Operation of the differential pressure indicator in cold weather, such as during winter, mostly oc-curs due to high viscosity, so check whether it is from clogging or not after normal operation starts.

•Once the differential pressure indicator is trig-gered, the indication continues to be displayed until the indicator is reset (by depressing the re-set button), even if the pump stops operating.Reset after replacing the element and restarting operation, or after normal operation starts in cold weather such as during winter.

• When using a differential pressure indication switch and if a filter clogged signal is incorpora-ted into the sequence circuit of the machine, make sure to design the system so the filter clog-ged signal does not operate until normal opera-tion starts.


• When the pressure difference reaches 0.18 MPa during filter operation (actuating the differential pressure indicator), stop operation, and replace the paper element or wash the micromesh ele-ment. If the micromesh element has reached the end of its service life, replace it.


• When washing the micromesh element, do not wipe it using a stiff brush or rag.


FH BA N 06 P M RHydraulic filter

010

B Max. 1.6 MPa

Operating pressure

A Vertical

Type

NWV


Phosphoric ester

Hydraulic fluid

061012

3/41 1/41 1/2

Port size (Rc)

Replacement Element Part No.Port size

(Nominal size)

06 (3/4B)

10 (1 1/4B)

12 (1 1/2B)

Paper Micromesh5 µm

EP001H-005NEP101H-005NEP201H-005N

10 µm

EP001H-010NEP101H-010NEP201H-010N

20 µm

EP001H-020NEP101H-020NEP201H-020N

5 µm

EM601H-005NEM701H-005NEM801H-005N

10 µm

EM601H-010NEM701H-010NEM801H-010N

20 µm

EM601H-020NEM701H-020NEM801H-020N

Element size

ø56 x 180ø76 x 190ø76 x 290

005010020

5 µm10 µm20 µm

Nominalfiltration

DME

None (Blanking cap)Differential pressure indicator



RD


Relief valve

How to Order

Note) The non-standard filtration is for micromesh elements only. Refer to page 444 for details.

PM

PaperMicromesh

Element

Note 1) The symbol at the end of the element part no. indicates the hydraulic fluid type. N: Petroleum, Phosphoric ester, W: Water-glycol, Emulsion.Note 2) Refer to page 444 for non-standard filtration.Note 3) Above elements require one element per filter.

Made to OrderNilX0

None (Standard)Non-standard filtration

Vertical Return Filter Series FHBA


w Seal

e O-ring

r O-ring

t O-ring

Element

Hexagon socket head cap screw

Conical spring washerCover

Body

q O-ring

Case

Spring

Guide

w Seal

2 x Rc port size (Nominal size)

Blanking cap

(Top plate for oil tank)

When actuating relief valve

INLET INLET

OUTLET

Replacement Seal List(One each of the seal and O-ring types listed below are required per filter.)


No.FHBA N -06W FHBA N -10W FHBA N -12W FHBAV-06 FHBAV-10 FHBAV-12

Description

JIS B2401-1A-G105

AL-207H

JIS B2401-1A-G85

JIS B2401-1A-G105

JIS B2401-1A-P40

O-ring for cover

Seal for cover

O-ring for case

O-ring for body

O-ring for element

JIS B2401-1A-G80

JIS B2401-1A-G65

JIS B2401-1A-G80

JIS B2401-1A-P26

JIS B2401-4D-G80

JIS B2401-4D-G65

AL-206H-VAL-206H

JIS B2401-4D-G80

JIS B2401-4D-P26

Phosphoric ester

JIS B2401-4D-G105

AL-207H-V

JIS B2401-4D-G85

JIS B2401-4D-G105

JIS B2401-4D-P40

431

FH�

HOW�


A A

øD

B BC

E

N

F F

COM.N.O.N.C.

View port G1/2

Two indication methods are available: differential pressure indicator and differential pressure indication switch. These can be mounted on all filter models.









Precautions1. The figures in the above table indicate stationary cur-

rent. 2. An inductive load has a power factor (AC) of 0.75 or

more, and a time constant (DC) of 7 msec or less. 3. A light load has an inrush current 10 times greater.4. Lead wires are connected using a screw tightening ter-

minal.5. The electrical entry is equipped with a conduit (G1/2)

and grommet. 6. Please wire freely to the microswitch indication symbol

1(COM.), 2(N.C.) and 3(N.O.).7. If a holding mechanism is necessary for the non-reset

type, provide it using electric circuits.

Dimensions

�K

�H

�J

4 x øPMounting hole

4 x M

øL ± 3

�K

Mounting base dimensions

( F)

INLET INLET

2 x Rc (d)

Rem

oval

dim

ensi

on G



( 34)



( 65)

62

3/4

1 1/4

1 1/2

Port size Rc (d)

55

75

A54

76

B 76

112

C65

89.1

D200

210

310

E299

342

442

F270

320

420

G 95

120

H100

128

J 75

100

K70

95

LM8

M10

M12

14

N10

12

P(mm)

Reset button

View port

Microswitch Rating

Ratedvoltage

Normallyclosed

Normallyopen

Resistance load

5 5 5 5 5 0.40.3


125 AC250 AC8 DC14 DC30 DC125 DC250 DC

Normallyclosed

Normallyopen

Light load

1.51

0.70.5

Normallyclosed

Normallyopen

Inductive load

4 4

4 4 0.40.3

5 4

Normallyclosed

Normallyopen

Motor load

2.51.5

1.30.8

3 3 3 0.1 0.05

3 3 3 0.1 0.05

(V)

432

Series FHBA


Selection of elements for different applicationsDepending on the application, the user can choose among several standard element types, paper elements (5, 10 and 20 µm) and micro-mesh elements (74 and 105 µm).

Easy maintenanceThe element slides into place and is sealed with an O-ring, making it easy to install and remove.

Large drain exhaust outletThe large M16 drain exhaust outlet assures rapid drainage.


FH100-06FH100-08FH100-10FH100-12FH100-16FH100-20FH100-24

3/4

1

1 1/4

1 1/2

2

2 1/2

3

60

100

150

200

300

550

700

50

80

120

160

260

450

600

Model Port size (Rc)Rated flow rate (l/min)

MicromeshPaper


Return Filter

Series FH100 RoHS

Fluid

Operating pressure


Main material

Element

Hydraulic fluid

Max. 1 MPa

Max. 80°CCast iron

Aluminum casting

NBR or FKM Note)

Stainless steel & NBR or Stainless steel & FKM Note)

0.6 MPa

0.13 MPa

0.15 MPa

Cover

Case

O-ring

Seal

Material

Nominal filtration


Specifications

Note) The material of the O-rings differs depending on the hydraulic fluid used.Petroleum, Water-glycol, Emulsion: NBR; Phosphoric ester: FKM

Paper

5, 10, 20 µm

Micromesh

74, 105 µm (200, 150 mesh)

CB-50H

CB-50H-V

CB-51H

CB-51H-V

AG-12H

AG-12H-W

AG-12H-V


Phosphoric ester


Phosphoric ester

Petroleum


Phosphoric ester





Accessory/Option



433

FH�

HOW�




06081012162024

3/41

1 1/41 1/2

22 1/2

3

Port size (Rc)

Hydraulic fluid

005010020074105

5 µm10 µm20 µm74 µm

105 µm

Nominal filtration


Model

FH100-06FH100-08FH100-10FH100-12FH100-16FH100-20FH100-24

5 µm

Paper Micromesh

EP420-005NEP420-005NEP020-005NEP020-005NEP520-005NEP620-005NEP620-005N

10 µm


20 µm


74 µm(200 mesh)


105 µm(150 mesh)


Element size

ø64 x 95

ø74 x 117

ø88 x 158

ø119 x 208

00 Element downward removal, threaded


How to Order

1 Max. 1 MPa

Operating pressure

045

NoneDifferential pressure indicator

Differential pressure indication switch Note)



01


Relief valve


Note) The paper elements for water-glycol or emulsion is 10 µm only.

PM

PaperMicromesh

Element

012


Phosphoric ester

Note 1) The symbol at the end of the element part no. indicates the hydraulic fluid type. N: Petroleum, V: Phosphoric ester, W: Water-glycol, Emulsion (10 µm only for paper)



Made to OrderNil

X0None (Standard)


Blanking cap

Cover

Case

Relief valve

e Seal washer

Element

q O-ring

w O-ring

DRAIN

INLET OUTLET

Drain plug

Differentialpressure

indication switch


Differential pressureindicator No.

Descrip-tion Hydraulic

fluid type


Phosphoricester

Model

FH100-

FH100-

06081012

16

202406081012

16

2024

JIS B2401-1A-G90

JIS B2401-1A-G130

AN6230-37NBR/Hs = 70

JIS B2401-1A-P35

JIS B2401-1A-P44

JIS B2401-1A-P50

JIS B2401-1A-P85

JIS B2401-4D-P35JIS B2401

-4D-G90

JIS B2401-4D-G130

AN6230-37FPM/Hs = 70

JIS B2401-4D-P44

JIS B2401-4D-P50

JIS B2401-4D-P85


O-ring forelement

Sealwasher

Standard Standard Part no.

SM-16

SM-16-V


434

Series FH100


COM.N.O.N.C.

View port G1/2







• This is a visual dual-purpose 2-stage display. Perform element replacement when the switch has actuated (when the red ring floats up and covers the entire view point).




ing. Then connect so that the drain is orien-ted downward. For maintenance, make sure to provide sufficient space above the filter for removing the element.

w Operation





• When the pressure difference reaches 0.13 MPa during filter operation (actuating the dif-ferential pressure indicator), stop operation, drain the oil from the case, and replace the pa-per element or wash the micromesh element. If the micromesh element has reached the end of its service life, replace it.


• When washing the micromesh element, do not wipe it using a stiff brush or rag.


0.1

0.05

0.03

0.01

0.005

0.00110 30 50 100 300 500

06

0810

1216

2024

0.05

0.03

0.01

0.005

0.003

0.00130 50 100 300 500

06

0810

1216

20

24

FH100-06 to 24: Nominal filtration 10 µm


Pre

ssur

e dr

op (

MP

a)

Flow rate (l/min)


Pre

ssur

e dr

op (

MP

a)

Flow rate (l/min)

Conditions Fluid: Turbine oil Class 2 VG56Measured pressure: 1 MPaViscosity: 45 mm2/sFilter material: MicromeshNominal filtration: 74 µm

FH100-06 to 24: Nominal filtration 74 µm

View port

Reset button

Microswitch Rating

Ratedvoltage

Normallyclosed

Normallyopen

Resistance load

5 5 5 5 5 0.40.3


125 AC250 AC8 DC14 DC30 DC125 DC250 DC

Normallyclosed

Normallyopen

Light load

1.51

0.70.5

Normallyclosed

Normallyopen

Inductive load

4 4

4 4 0.40.3

5 4

Normallyclosed

Normallyopen

Motor load

2.51.5

1.30.8

3 3 3 0.1 0.05

3 3 3 0.1 0.05








(V)

435

Return Filter Series FH100

FH�

HOW�


INLET

OUTLET

DRAIN

A

CD

øB

øF

C C

62

INLET

OUTLET

(65)



Dimensions

DRAIN

E (

Ele

men

t rem

oval

dim

ensi

on)

2 x Rc (d)Blanking cap

INLET

OUTLET


(34)


Model

FH100-06FH100-08FH100-10FH100-12FH100-16FH100-20FH100-24

3/4

1

1 1/4

1 1/2

2

2 1/2

3

d

102

110

150

200

A

90

100

128

157

B

35

45

52

70

C

200

265

299

387

D

290

380

430

540

E

104

144

175

F

2.5

4.3

6.8

17.5

Mass (kg)

(mm)

436

Series FH100


Compact and lightweightThe compact and lightweight design employs an aluminum alloy cover.

Easy maintenanceThe element slides into place, making it easy to install and remove.


FH150-02FH150-03FH150-04

1/4

3/8

1/2

5

10

20

Model Port size (Rc) Rated flow rate (l/min)


Oil Filter

Series FH150 RoHS

Fluid

Operating pressure


Main material

Element


Hydraulic fluid

Max. 1 MPa

Max. 80°CAluminum die-cast

Steel plate

NBR or FKM Note)

Paper

5, 10, 20 µm

0.6 MPa

0.13 MPa

Cover

Case

O-ring

Material

Nominal filtration


Specifications

Note) The material of the O-rings and seals differs depending on the hydraulic fluid used.Petroleum, Water-glycol, Emulsion: NBR; Phosphoric ester: FKM

CB-50H

CB-50H-V

CB-51H

CB-51H-V

AG-12H

AG-12H-W

AG-12H-V

B-44P


Phosphoric ester


Phosphoric ester

Petroleum


Phosphoric ester


Bracket




Accessory/Option

—

437

FH�

HOW�




020304

1/43/81/2

Port size (Rc)


1 None

Relief valve

BNil None

With bracket

Bracket

005010020

5 µm10 µm20 µm

Nominal filtration

PM

PaperMicromesh

Element

Replacement Element Part No. (Including O-ring for element)Model

FH150-02FH150-03FH150-04

5 µm

EP910-005N

10 µm

EP910-010N

20 µm

EP910-020N

Element size

ø53 x 90

Note 1) The symbol at the end of the element part no. indicates the hydraulic fluid type. N: Petroleum, V: Phosphoric ester, W: Water-glycol, Emulsion (10 µm only)


50 Element downward removal, threaded


Oil filter

How to Order

1 Max. 1 MPa

Operating pressure

045

None




Note) 10 µm only for water-glycol or emulsion.

Hydraulic fluid012


Phosphoric ester


Made to OrderNil

X0None (Standard)


Blanking cap

Cover

Case

Clamp ring

Elementq O-ring

w O-ring

INLET OUTLET

Spring



INLET OUTLET

Differentialpressure

indication switch


INLET OUTLET

No.Descrip-



Phosphoricester

Model

FH150-

FH150-

020304020304

JIS B2401-1A-P30

JIS B2401-4D-P30


O-ring forelement

Standard Standard

1A-S65

4D-S65

Replacement Seal List (One each of the O-ring types listed below is required per filter.)

438

Series FH150


COM.N.O.N.C.

View port G1/2












ing. Then connect so that the case is oriented downward. For maintenance, make sure to provide sufficient space above the filter for re-moving the element.

w Operation





• When the pressure difference reaches 0.13 MPa during operation (actuating the differen-tial pressure indicator), stop operation and re-place the element.

• When replacing the element, drain the fluid from the case. Also, check the O-rings and replace them if they are damaged.

r Other

• Refer to the operating manual regarding the tightening torque for clamping ring.Use a commercially available hook wrench (applicable sizes 80 to 85 mm) for tightening and removing clamping rings.


0.050.04

0.03

0.02

0.01

0.005

0.0012 3 4 65 7 8 9 10 20 30 40 50

02

03

04

Pre

ssur

e dr

op (

MP

a)

Flow rate (l/min)


FH150-02 to 04

View port

Reset button

Microswitch Rating

Ratedvoltage

Normallyclosed

Normallyopen

Resistance load

5 5 5 5 5 0.40.3


125 AC250 AC8 DC14 DC30 DC125 DC250 DC

Normallyclosed

Normallyopen

Light load

1.51

0.70.5

Normallyclosed

Normallyopen

Inductive load

4 4

4 4 0.40.3

5 4

Normallyclosed

Normallyopen

Motor load

2.51.5

1.30.8

3 3 3 0.1 0.05

3 3 3 0.1 0.05








(V)

439

Oil Filter Series FH150

FH�

HOW�


H

AEF

BC

G

J

FH150-02FH150-03FH150-04

Model

1/4

3/8

1/2

d

80

A

168.5

B

197.5

C

259.5

D

50

E

15

F

25

G

7

H

6.5

J

0.7

Mass (kg)

(mm)

Dimensions

D (

Ele

men

t rem

oval

dim

ensi

on)

2 x Rc (d)

OUTLET

INLET

29ø16


(34)

29 INLET




(65)

29

62

OUTLET

440

Series FH150


Magnetic separator

Magnetic separator

Magnetic separator

q U-turn flow type w Underflow type e Overflow type

Magnetic Separator Installation Examples

Contaminant density of 200 ppm Separator after contaminant adsorption

Fluid after cleaning with magnetic separator (5 ppm)

These magnetic separators protect machinery from malfunctions, reduced precision, and burnout by adsorbing and eliminating contaminants in the fluid by means of magnetism. This helps extend the service life of hydraulic equipment.

Zero running costSince there are no consumable parts, the run-ning cost is basically zero and the magnetic separator can be used semi-permanently.

Extends service life of hydraulic fluidBy adsorbing and eliminating contaminants, the magnetic separator retards deterioration of the hydraulic fluid and makes it possible to extend the fluid replacement time.

Reduced maintenance costsThe magnetic separator prevents mechanical problems caused by contaminants such as abrasive particles and greatly reduces mainte-nance costs.

Fluid


Fluid speedMax. 80°C

3 m/min or less

FHMN: Petroleum, Water-glycol, Cutting oil, Emulsion

FHMV: Phosphoric ester

Specifications

FHM�-055FHM-100FHM-200

20

100

200

0.2

0.9

2.5

�55 x t20

�100 x t30

200 x 140 x t40

Model Applicable fluid storage volume (l/unit) Note) Mass (kg)Dimension (mm)

Model

Magnetic Separator

Series FHM RoHS

Note) For example, three FHM100 magnetic separator units would be sufficient for a 300-liter fluid storage tank.

441

FH�

HOW�

RoHS-FHM.qxd 10.7.26 6:12 PM Page 1



Base plate

MagnetCover Adsorption

surface

Magnet

Rubber caseAdsorption surface

Base plate

MagnetHexagon sockethead cap screw

CoverAdsorption surface

100

90

80

70

60

50

40

30

20

10

01 5 10 50 100

FHM�-055100200300400500

100

90

80

70

60

50

40

30

20

10

0

100200300400500

1 5 10 50 100

FHM-200

FHM-200

100

9080

7060

50

40

30

20

10

0

75

1 5 10 5030 100

FHM-100100200300400500

Fluid Iron Content Elimination Performance by Iron Particle Concentration

FHM N 055

055 �55 x t20

Main unit representative dimensions

Magneticseparator

Petroleum, Water-glycol,Cutting oil, Emulsion

Phosphoric ester

Fluid

N

V

FHM 100

100200

�100 x t30200 x 140 x t40

Main unit representative dimensions

Magneticseparator

How to Order

Elim

inat

ion

ratio

(%

)

Flow-back count

Fluid: Hydraulic fluid

Elim

inat

ion

ratio

(%

)

Flow-back count


Elim

inat

ion

ratio

(%

)

Flow-back count


Example: Elimination ratio and concentration after using the FHM-100 for one hour under the following conditions.Conditions

Explanation of graph Explanation of graph

1. Volume of fluid in tank: 200 l2. Pump-out volume: 100 l/min3. Contaminant concentration of used fluid:

500 ppm (initial concentration, percentage by volume)4. Number of separators: 2 pcs. (applicable fluid storage volume of 100 l/unit)

Calculate the flow-back count (N).

N = = = Pump-out volume x Operation timeVolume of fluid in tank

100 x 60200

30

FHM�-055

Construction

FHM-100

Based on the elimination ratio data for the FHM�-100 and the point where the 500 ppm line and flow-back count 30 line intersect (one hour after starting operation), the result is 75%.

442

Series FHM


20�

55

200

140

7020

40

115

�10

0

15

30


(M6 x 10) 2 pcs.

Hexagon socket head cap screw(M6 x 10) 4 pcs.

FHM-200

FHM-100


FHM�-055

Dimensions

Mountingq The flat portion of the stainless steel cover functions as the con-

taminant adsorption surface. However, for FHM�-055, the flat por-tion of the magnetic material functions as the contaminant adsorp-tion surface.

w Mount the magnetic separator in a location where fluid is constant-ly flowing by in laminar flow.

e Avoid locations such as near the suction pipe or return pipe, pla-ces where there is turbulence, and locations where the flow speed is 3 m/min or greater.

r If necessary, fix the separator in place. If frequent cleaning will be necessary, it can be suspended from the top panel of the tank.

t If a fluid switch (built-in lead switch) or the like is used, it should be installed in a location where it will not be affected by magnetism from the separator. (Refer to the technical data sheet (SM-82-006) for information on magnetic fields.)

Maintenanceq Clean the separator regularly. Make sure to clean it once the accu-

mulation of contaminants reaches a thickness of 20 mm or so.w Clean the adsorption surface of the separator by wiping away the

accumulated contaminants using a soft rag or the like.

Handlingq Do not bring the top surface of the separator near magnetically at-

tractive objects such as iron plates.w Handle the separators individually and do not bring them into close

proximity with each other.e Be careful not to get your fingers caught between iron plates, etc.,

when installing the separator.r Do not bring objects that are affected by magnetism (cards with

magnetic strips, watches, etc.) near the separator.

Handle-equipped type Cover/handle-equipped type

Tank-fixed type

443

Magnetic Separator Series FHM

FH�

HOW�


Made to Order Specifications:Please consult with SMC for detailed specifications, delivery and prices.

FHIA(Refer to P. 415.)

1/2

3/4, 1

1 1/4, 1 1/2

2

2 1/2, 3

3 1/2, 4

1/2, 3/4

1,1 1/4

1 1/2

2

2 1/2

3

3 1/2, 4

1/2, 3/4, 1

1 1/4, 1 1/2, 2

2 1/2, 3

3/8, 1/2

3/4, 1

1 1/4, 1 1/2

2

2 1/2, 3

3/4

1 1/4

1 1/2

3/4, 1

1 1/4, 1 1/2

2

2 1/2, 3

1/4, 3/8, 1/2

Replacement element part no.

Micromesh element(With relief valve)

—

—

—

—

—

—

EM520-∗1∗2

EM620-∗1∗2

EM720-∗1∗2

EM820-∗1∗2

EM920-∗1∗2

EM030-∗1∗2

EM130-∗1∗2

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

ø65 x l 90

ø85 x l 110

ø100 x l 160

ø120 x l 180

ø140 x l 200

ø180 x l 260

ø65 x l 90

ø82 x l 133

ø104 x l 177

ø104 x l 177

ø132 x l 212

ø132 x l 212

ø155 x l 193

ø69 x l 88

ø89 x l 123

ø109 x l 188

ø53.1 x l 90

ø73.5 x l 117

ø73.5 x l 195

ø87.6 x l 282

ø118.7 x l 280

ø56 x l 180

ø76 x l 190

ø76 x l 290

ø65 x l 95

ø73.5 x l 117

ø87.6 x l 157

ø118.7 x l 207

ø53 x l 90

Description Model Port size

EM001H-∗1∗2

EM101H-∗1∗2

EM201H-∗1∗2

EM301H-∗1∗2

EM401H-∗1∗2

EM501H-∗1∗2

EM230-∗1∗2

EM330-∗1∗2

EM430-∗1∗2

EM530-∗1∗2

EM630-∗1∗2

EM730-∗1∗2

EM830-∗1∗2

EM220-∗1∗2

EM320-∗1∗2

EM420-∗1∗2

EM040-∗1∗2

EM910-∗1∗2

EM140-∗1∗2

EM930-∗1∗2

EM240-∗1∗2

EM601H-∗1∗2

EM701H-∗1∗2

EM801H-∗1∗2

EM810-∗1∗2

EM910-∗1∗2

EM020-∗1∗2

EM120-∗1∗2

EM040-∗1∗2

Micromesh element Element size

Vertical suction filter

Oil filter

Return filter

Vertical return filter

Line filter

Suction guard

Suction filter with case

FH150(Refer to P. 438.)


FHBA(Refer to P. 431.)

FH34FH44FH54FH64

(Refer to P. 427.)

FHG(Refer to P. 423.)


Note) In the table above ∗1 indicates nominal filtration and ∗2 indicates hydraulic fluid type.

Made to Order(Non-standard filtration)

X0Filter symbol (Refer to “How to Order” for each series)

Hydraulic Filter Non-Standard Filtration Replacement Element Part No.

Symbol (∗1)

003005010020040074105149270

µm 3 5 10 20 40 74105149270

Nominal FiltrationSymbol (∗2)

N

W

V

Type

Hydraulic Fluid

How to Order (Non-Standard Filtration)

Note) Made-to-order specifications (non-standard filtration rating) are available only for micromesh elements (element symbol: M).

Petroleum


Phosphoric ester

Series FH

444

Made toOrder


Series FHSpecific Product PrecautionsBe sure to read this before handling.Refer to front matters 30 and 31 for Safety Instructions.

Design

Caution1. Do not use at a pressure that exceeds the operating

pressure range.2. Do not use at a temperature that exceeds the oper-

ating temperature range.3. Fluid

Do not use the product with gases. Do not use fluid other than hydraulic fluid.

4. Fatigue damageUnder the following conditions, special measures are required:

1. If the product will be subjected to pressure surges.

2. If the product is not mounted securely and will be subject to friction or vibrations.

5. CorrosionThe product may corrode depending on usage conditions and environment.

Selection

Warning1. When selecting products, carefully consider the us-

age purpose, the required specifications, and the usage conditions (fluid, pressure, flow rate, temper-ature, environment), and ensure that the specifica-tion range is not exceeded.

2. The fluid used must not be heated to the boiling point.

3. Do not use the product with air or other gases un-der any circumstances.

4. Do not use the product in circumstances where it will be exposed to pressure that exceeds the rated operating pressure range, such as with a water hammer or surge pressure.

Fluid

Warning1. Do not use fluid other than hydraulic fluid.

Piping

Caution1. Make sure to allow sufficient space for maintenance

when installing and piping.2. Connections

Make sure no cutting chips from pipe threads or sealing mate-rial gets inside the piping. If sealing tape is used, leave 1.5 to 2 thread ridges exposed at the end of the male thread.

3. Filter installationUse stays or the like to secure the inlet and outlet pipes so that the filter unit is not subjected to external force such as vi-bration.

Operating Environment

Caution1. If the product is used in an environment or location

conducive to corrosion, discoloration or deteriora-tion due to corrosion may occur.

2. Fatigue damage may occur if the product is used in a location subject to vibrations or impacts.

Maintenance

Caution1. The differential pressure will increase if the filter be-

comes clogged with foreign matter.The differential pressure indicator operation pressure is the pressure difference at which the element should be replaced. When the pressure difference rises to this level, replace the element with a new one. A differential pressure indicator and differential pressure indication switch are available as options.

445

FH�

HOW�


smc pneumatics fh hydraulic filters · fh how courtesy of steven engineering, inc.-230 ryan way,...

Documents