small one board usb2.0 color / monochrome cameras€¦ · cannot get any image from the usb camera....
TRANSCRIPT
STCSpecifications
SmallColor / Monochrome Cameras
STCSTCSTC
Product Specifications
STC-SC33USBSpecifications
Small One BoardColor / Monochrome Cameras
STC-SC33USB / SB33USBSTC-SC83USB / SB83USBSTC-SC133USB / SB133USB
Product Specifications
SC33USB / STC-SB33USB
One BoardColor / Monochrome Cameras
SC33USB / SB33USBSC83USB / SB83USBSC133USB / SB133USB
Product Specifications
SB33USB / STC
One Board Color / Monochrome Cameras
SC33USB / SB33USBSC83USB / SB83USBSC133USB / SB133USB
Product Specifications
STC-SC83USB
USB2.0Color / Monochrome Cameras
SC33USB / SB33USBSC83USB / SB83USBSC133USB / SB133USB
SC83USB / STC-SB83USB
USB2.0 Color / Monochrome Cameras
SC33USB / SB33USB SC83USB / SB83USB SC133USB / SB133USB
SB83USB / STC
Color / Monochrome Cameras
(VGA) (XGA)
(1.3M
STC-SC133USB
(VGA) (XGA) 1.3M)
USB / STC-SB133USB
No.13S007
SB133USB
No.13S007-07
1
STCSpecifications
Caution for the PC with the Intel Core i3, i5 or i7When use the USB camera with some PC, which has the Intel Core i3, i5 or i7, may occur following issue:
CANNOT get any image from the USB camera.
Frame drops
(This issue may occurred for the other manufacture USB camera too)
Cause of this issue:
The image data cannot transfer to the PC because the Intel Core i3, i5 or i7 CPU switch to the power save mode
frequently while the image is transferring.
Solution for this
1. Disable the power save mode with change the BIOS settings.
Please change BIOS setting with your responsibility.
The power consumption and the heat of the PC are increased when disable the power save mode. Please understand
and accept this before
2. Disable the power save mode with the Sentech PC power management software.
The power save mode can disable with the Sentech PC power management software “StPowerCtrl”.
Please contact to the Sales
The power consumption and the heat of the PC are increased when disable the power save mode. Please understand
and accept this before disable the power save mode.
3. Change the camera clock from “Normal” to “1/2” or “1/4”. (Reduce the frame rat
Caution for the connecting USB device
Please DO NOT connects or disconnect any USB devices including USB memory while use this USB camera.Its possibility to the USB camera DOES NOT recognize after connect or disconnect USB devices.
STC-SC33USBSpecifications
Caution for the PC with the Intel Core i3, i5 or i7When use the USB camera with some PC, which has the Intel Core i3, i5 or i7, may occur following issue:
CANNOT get any image from the USB camera.
Frame drops
issue may occurred for the other manufacture USB camera too)
Cause of this issue:
The image data cannot transfer to the PC because the Intel Core i3, i5 or i7 CPU switch to the power save mode
frequently while the image is transferring.
Solution for this issue:
1. Disable the power save mode with change the BIOS settings.
Please change BIOS setting with your responsibility.
The power consumption and the heat of the PC are increased when disable the power save mode. Please understand
and accept this before
2. Disable the power save mode with the Sentech PC power management software.
The power save mode can disable with the Sentech PC power management software “StPowerCtrl”.
Please contact to the Sales
The power consumption and the heat of the PC are increased when disable the power save mode. Please understand
and accept this before disable the power save mode.
3. Change the camera clock from “Normal” to “1/2” or “1/4”. (Reduce the frame rat
Caution for the connecting USB device
Please DO NOT connects or disconnect any USB devices including USB memory while use this USB camera.Its possibility to the USB camera DOES NOT recognize after connect or disconnect USB devices.
SC33USB / STC-SB33USB
Caution for the PC with the Intel Core i3, i5 or i7When use the USB camera with some PC, which has the Intel Core i3, i5 or i7, may occur following issue:
CANNOT get any image from the USB camera.
Frame drops frequently
issue may occurred for the other manufacture USB camera too)
Cause of this issue:
The image data cannot transfer to the PC because the Intel Core i3, i5 or i7 CPU switch to the power save mode
frequently while the image is transferring.
issue:
1. Disable the power save mode with change the BIOS settings.
Please change BIOS setting with your responsibility.
The power consumption and the heat of the PC are increased when disable the power save mode. Please understand
and accept this before disable the power save mode.
2. Disable the power save mode with the Sentech PC power management software.
The power save mode can disable with the Sentech PC power management software “StPowerCtrl”.
Please contact to the Sales
The power consumption and the heat of the PC are increased when disable the power save mode. Please understand
and accept this before disable the power save mode.
3. Change the camera clock from “Normal” to “1/2” or “1/4”. (Reduce the frame rat
Caution for the connecting USB device
Please DO NOT connects or disconnect any USB devices including USB memory while use this USB camera.Its possibility to the USB camera DOES NOT recognize after connect or disconnect USB devices.
SB33USB / STC
Caution for the PC with the Intel Core i3, i5 or i7When use the USB camera with some PC, which has the Intel Core i3, i5 or i7, may occur following issue:
CANNOT get any image from the USB camera.
issue may occurred for the other manufacture USB camera too)
The image data cannot transfer to the PC because the Intel Core i3, i5 or i7 CPU switch to the power save mode
frequently while the image is transferring.
1. Disable the power save mode with change the BIOS settings.
Please change BIOS setting with your responsibility.
The power consumption and the heat of the PC are increased when disable the power save mode. Please understand
disable the power save mode.
2. Disable the power save mode with the Sentech PC power management software.
The power save mode can disable with the Sentech PC power management software “StPowerCtrl”.
Please contact to the Sales representative about this
The power consumption and the heat of the PC are increased when disable the power save mode. Please understand
and accept this before disable the power save mode.
3. Change the camera clock from “Normal” to “1/2” or “1/4”. (Reduce the frame rat
Caution for the connecting USB device
Please DO NOT connects or disconnect any USB devices including USB memory while use this USB camera.Its possibility to the USB camera DOES NOT recognize after connect or disconnect USB devices.
STC-SC83USB
Caution for the PC with the Intel Core i3, i5 or i7When use the USB camera with some PC, which has the Intel Core i3, i5 or i7, may occur following issue:
CANNOT get any image from the USB camera.
issue may occurred for the other manufacture USB camera too)
The image data cannot transfer to the PC because the Intel Core i3, i5 or i7 CPU switch to the power save mode
frequently while the image is transferring.
1. Disable the power save mode with change the BIOS settings.
Please change BIOS setting with your responsibility.
The power consumption and the heat of the PC are increased when disable the power save mode. Please understand
disable the power save mode.
2. Disable the power save mode with the Sentech PC power management software.
The power save mode can disable with the Sentech PC power management software “StPowerCtrl”.
representative about this
The power consumption and the heat of the PC are increased when disable the power save mode. Please understand
and accept this before disable the power save mode.
3. Change the camera clock from “Normal” to “1/2” or “1/4”. (Reduce the frame rat
Caution for the connecting USB device
Please DO NOT connects or disconnect any USB devices including USB memory while use this USB camera.Its possibility to the USB camera DOES NOT recognize after connect or disconnect USB devices.
SC83USB / STC-SB83USB
Caution for the PC with the Intel Core i3, i5 or i7When use the USB camera with some PC, which has the Intel Core i3, i5 or i7, may occur following issue:
issue may occurred for the other manufacture USB camera too)
The image data cannot transfer to the PC because the Intel Core i3, i5 or i7 CPU switch to the power save mode
1. Disable the power save mode with change the BIOS settings.
Please change BIOS setting with your responsibility.
The power consumption and the heat of the PC are increased when disable the power save mode. Please understand
disable the power save mode.
2. Disable the power save mode with the Sentech PC power management software.
The power save mode can disable with the Sentech PC power management software “StPowerCtrl”.
representative about this software.
The power consumption and the heat of the PC are increased when disable the power save mode. Please understand
and accept this before disable the power save mode.
3. Change the camera clock from “Normal” to “1/2” or “1/4”. (Reduce the frame rat
Caution for the connecting USB device
Please DO NOT connects or disconnect any USB devices including USB memory while use this USB camera.Its possibility to the USB camera DOES NOT recognize after connect or disconnect USB devices.
SB83USB / STC
Caution for the PC with the Intel Core i3, i5 or i7When use the USB camera with some PC, which has the Intel Core i3, i5 or i7, may occur following issue:
issue may occurred for the other manufacture USB camera too)
The image data cannot transfer to the PC because the Intel Core i3, i5 or i7 CPU switch to the power save mode
1. Disable the power save mode with change the BIOS settings.
The power consumption and the heat of the PC are increased when disable the power save mode. Please understand
2. Disable the power save mode with the Sentech PC power management software.
The power save mode can disable with the Sentech PC power management software “StPowerCtrl”.
software.
The power consumption and the heat of the PC are increased when disable the power save mode. Please understand
3. Change the camera clock from “Normal” to “1/2” or “1/4”. (Reduce the frame rat
Please DO NOT connects or disconnect any USB devices including USB memory while use this USB camera.Its possibility to the USB camera DOES NOT recognize after connect or disconnect USB devices.
STC-SC133USB
Caution for the PC with the Intel Core i3, i5 or i7When use the USB camera with some PC, which has the Intel Core i3, i5 or i7, may occur following issue:
The image data cannot transfer to the PC because the Intel Core i3, i5 or i7 CPU switch to the power save mode
The power consumption and the heat of the PC are increased when disable the power save mode. Please understand
2. Disable the power save mode with the Sentech PC power management software.
The power save mode can disable with the Sentech PC power management software “StPowerCtrl”.
The power consumption and the heat of the PC are increased when disable the power save mode. Please understand
3. Change the camera clock from “Normal” to “1/2” or “1/4”. (Reduce the frame rate)
Please DO NOT connects or disconnect any USB devices including USB memory while use this USB camera.Its possibility to the USB camera DOES NOT recognize after connect or disconnect USB devices.
USB / STC-SB133USB
Caution for the PC with the Intel Core i3, i5 or i7When use the USB camera with some PC, which has the Intel Core i3, i5 or i7, may occur following issue:
The image data cannot transfer to the PC because the Intel Core i3, i5 or i7 CPU switch to the power save mode
The power consumption and the heat of the PC are increased when disable the power save mode. Please understand
The power save mode can disable with the Sentech PC power management software “StPowerCtrl”.
The power consumption and the heat of the PC are increased when disable the power save mode. Please understand
Please DO NOT connects or disconnect any USB devices including USB memory while use this USB camera.Its possibility to the USB camera DOES NOT recognize after connect or disconnect USB devices.
No.13S007
SB133USB
Caution for the PC with the Intel Core i3, i5 or i7 When use the USB camera with some PC, which has the Intel Core i3, i5 or i7, may occur following issue:
The image data cannot transfer to the PC because the Intel Core i3, i5 or i7 CPU switch to the power save mode
The power consumption and the heat of the PC are increased when disable the power save mode. Please understand
The power save mode can disable with the Sentech PC power management software “StPowerCtrl”.
The power consumption and the heat of the PC are increased when disable the power save mode. Please understand
Please DO NOT connects or disconnect any USB devices including USB memory while use this USB camera.Its possibility to the USB camera DOES NOT recognize after connect or disconnect USB devices.
No.13S007-07
2
The image data cannot transfer to the PC because the Intel Core i3, i5 or i7 CPU switch to the power save mode
The power consumption and the heat of the PC are increased when disable the power save mode. Please understand
The power consumption and the heat of the PC are increased when disable the power save mode. Please understand
Please DO NOT connects or disconnect any USB devices including USB memory while use this USB camera.
STCSpecifications
Table
1
1.1 1.2 1.3 1.4 1.5 1.6
2
2.1 2.1.12.1.22.1.3
3
4
4.1 4.1.14.1.24.1.34.1.44.2 4.2.14.2.24.2.3
5
5.1 5.2 5.3 5.4 5.5 5.6
6
Figure 1. Naming RuleFigure 2.Spectral Sensitivity Characteristics on STCFigure 3.Spectral Sensitivity Characteristics on STCFigure 4.SpectFigure 5.Spectral Sensitivity Characteristics on Figure 6.Spectral Sensitivity Characteristics on STCFigure 7.Spectral Sensitivity Characteristics on STCFigure 8.Back view on STCFigure 9.Connector on the rear panelFigure 10.Input circuit diagramFigure 11.Output response timeFigure 12.Output circuit diagramFigure 14.Mechanical dimensionsFigure 15. Mechanical dimensionsFigure13.Mechanical dimensionsFigure 16.Mechanical dimensionsFigure 17.Mechanical dimensionsFigure 18.Mechanical dimensions
STC-SC33USBSpecifications
Table of Contents
Overview
Features Specification of Naming Support Application Option model Power Supply Pixel Blemish Static Collection and Saving Camera Settings
Specifications
Electronic specifications / Mechanical specifications / Environmental specifications2.1.1 STC2.1.2 STC2.1.3 STC
Interface Connector Specifications(Board Type)
Input / Output signals specifications
Input signals specifications4.1.1 Function for the input signals4.1.2 Characteristics of the input signals4.1.3 Input signal circuit (Include reset signal)4.1.4 Reset signal
Output signals specifications4.2.1 Function for the output signals4.2.2 Characte4.2.3 Output signal circuit
Dimensions
STC-SCxxxUSB STC-SBxxxUSB STC-SCxxxUSB STC-SCxxxUSB STC-SBxxxUSB STC-SCxxxUSB
Revisions
Figure 1. Naming RuleFigure 2.Spectral Sensitivity Characteristics on STCFigure 3.Spectral Sensitivity Characteristics on STCFigure 4.Spectral Sensitivity Characteristics on STCFigure 5.Spectral Sensitivity Characteristics on Figure 6.Spectral Sensitivity Characteristics on STCFigure 7.Spectral Sensitivity Characteristics on STCFigure 8.Back view on STCFigure 9.Connector on the rear panelFigure 10.Input circuit diagramFigure 11.Output response timeFigure 12.Output circuit diagramFigure 14.Mechanical dimensionsFigure 15. Mechanical dimensionsFigure13.Mechanical dimensionsFigure 16.Mechanical dimensionsFigure 17.Mechanical dimensionsFigure 18.Mechanical dimensions
SC33USB / STC-SB33USB
Contents
Overview ................................
Features ................................Specification of NamingSupport Application................................Option model ................................Power Supply ................................Pixel Blemish Static Collection and Saving Camera Settings
Specifications ................................
Electronic specifications / Mechanical specifications / Environmental specificationsSTC-SC33USB / STCSTC-SC83USB / STCSTC-SC133USB / STC
Interface Connector Specifications(Board Type)
Input / Output signals specifications
Input signals specificationsFunction for the input signalsCharacteristics of the input signals
put signal circuit (Include reset signal)Reset signal ................................
Output signals specificationsFunction for the output signalsCharacteristics of the output signalsOutput signal circuit
Dimensions ................................
SCxxxUSB-BxCS (Color, Board type, CSSBxxxUSB-BLCS (Monochrome, Board type, CSSCxxxUSB-BL / SCxxxUSB-BLL (Color, Board tSBxxxUSB-BLL (Monochrome, Board type, Fixed Focus, USB Angle / Straight*)SCxxxUSB-AL / STC
Revisions ................................
Figure 1. Naming Rule ................................Figure 2.Spectral Sensitivity Characteristics on STCFigure 3.Spectral Sensitivity Characteristics on STC
ral Sensitivity Characteristics on STCFigure 5.Spectral Sensitivity Characteristics on Figure 6.Spectral Sensitivity Characteristics on STCFigure 7.Spectral Sensitivity Characteristics on STCFigure 8.Back view on STC-SC/SB**USB SeriesFigure 9.Connector on the rear panelFigure 10.Input circuit diagramFigure 11.Output response timeFigure 12.Output circuit diagramFigure 14.Mechanical dimensionsFigure 15. Mechanical dimensionsFigure13.Mechanical dimensionsFigure 16.Mechanical dimensionsFigure 17.Mechanical dimensionsFigure 18.Mechanical dimensions
SB33USB / STC
................................................................
................................................................Specification of Naming ................................
................................................................................................
Pixel Blemish Static Collection and Saving Camera Settings
................................
Electronic specifications / Mechanical specifications / Environmental specificationsSC33USB / STC-SB33USBSC83USB / STC-SB83USBSC133USB / STC-SB133USB
Interface Connector Specifications(Board Type)
Input / Output signals specifications
Input signals specifications ................................Function for the input signalsCharacteristics of the input signals
put signal circuit (Include reset signal)................................
Output signals specifications ................................Function for the output signals
ristics of the output signalsOutput signal circuit ................................
................................
BxCS (Color, Board type, CSBLCS (Monochrome, Board type, CSBL / STC-SBxxxUSBBLL (Color, Board tBLL (Monochrome, Board type, Fixed Focus, USB Angle / Straight*)AL / STC-SBxxxUSB
................................................................
................................Figure 2.Spectral Sensitivity Characteristics on STCFigure 3.Spectral Sensitivity Characteristics on STC
ral Sensitivity Characteristics on STCFigure 5.Spectral Sensitivity Characteristics on Figure 6.Spectral Sensitivity Characteristics on STCFigure 7.Spectral Sensitivity Characteristics on STC
SC/SB**USB SeriesFigure 9.Connector on the rear panel ................................Figure 10.Input circuit diagram ................................Figure 11.Output response time ................................Figure 12.Output circuit diagram ................................Figure 14.Mechanical dimensions (STC-SCxxxUSBFigure 15. Mechanical dimensions (STC-SBxxxUSBFigure13.Mechanical dimensions (STC-SCxxxUSBFigure 16.Mechanical dimensions (STC-SCxxxUSBFigure 17.Mechanical dimensions (STC-SBxxxUSBFigure 18.Mechanical dimensions (STC-SCxxxUSB
STC-SC83USB
................................
................................................................................................
................................................................................................................................................................................................
Pixel Blemish Static Collection and Saving Camera Settings
................................................................
Electronic specifications / Mechanical specifications / Environmental specificationsSB33USB ................................SB83USB ................................
SB133USB ................................
Interface Connector Specifications(Board Type)
Input / Output signals specifications ................................
................................Function for the input signals ................................Characteristics of the input signals ................................
put signal circuit (Include reset signal)................................................................
................................Function for the output signals ................................
ristics of the output signals ................................................................
................................................................
BxCS (Color, Board type, CSBLCS (Monochrome, Board type, CS
SBxxxUSB-BL (Color / Monochrome, Board type, NoBLL (Color, Board type, Fixed Focus, USB Angle / Straight*)BLL (Monochrome, Board type, Fixed Focus, USB Angle / Straight*)
SBxxxUSB-AL (Color / Monochrome, Cased type, CS
................................
................................................................Figure 2.Spectral Sensitivity Characteristics on STC-SC33USB (with IR cut filter)Figure 3.Spectral Sensitivity Characteristics on STC-SB33USB
ral Sensitivity Characteristics on STC-SC83USB (with IR cut filter)Figure 5.Spectral Sensitivity Characteristics on STC-SB83USBFigure 6.Spectral Sensitivity Characteristics on STC-SC133USB (with IR cut filter)Figure 7.Spectral Sensitivity Characteristics on STC-SB133USB
SC/SB**USB Series ................................................................
................................................................................................................................................................................................
SCxxxUSB-BxCS)SBxxxUSB-BLCS)
SCxxxUSB-BL / STCSCxxxUSB-BLL)SBxxxUSB-BLL)SCxxxUSB-AL / STC
SC83USB / STC-SB83USB
................................................................
................................................................................................
................................................................................................................................................................
Pixel Blemish Static Collection and Saving Camera Settings
................................................................
Electronic specifications / Mechanical specifications / Environmental specifications................................................................
................................
Interface Connector Specifications(Board Type) ................................
................................
................................................................................................................................
................................put signal circuit (Include reset signal) ................................
................................................................................................
................................................................
................................................................
................................................................
BxCS (Color, Board type, CS-Mount, USB Angle / Straight)BLCS (Monochrome, Board type, CS-Mount, USB Angle / Straight* )
BL (Color / Monochrome, Board type, Noype, Fixed Focus, USB Angle / Straight*)
BLL (Monochrome, Board type, Fixed Focus, USB Angle / Straight*)AL (Color / Monochrome, Cased type, CS
................................................................
................................................................SC33USB (with IR cut filter)SB33USB ................................SC83USB (with IR cut filter)SB83USB ................................SC133USB (with IR cut filter)SB133USB ................................
................................................................................................
................................................................................................BxCS) ................................BLCS) ................................
BL / STC-SBxxxUSBBLL) ................................BLL) ................................AL / STC-SBxxxUSB
SB83USB / STC
................................
................................................................................................................................
................................................................................................................................
Pixel Blemish Static Collection and Saving Camera Settings ................................
................................
Electronic specifications / Mechanical specifications / Environmental specifications................................................................................................................................
................................................................
................................
................................................................
................................................................................................
................................................................................................................................
................................................................................................................................
................................................................................................................................
................................................................
................................
Mount, USB Angle / Straight)Mount, USB Angle / Straight* )
BL (Color / Monochrome, Board type, Noype, Fixed Focus, USB Angle / Straight*)
BLL (Monochrome, Board type, Fixed Focus, USB Angle / Straight*)AL (Color / Monochrome, Cased type, CS
................................
................................SC33USB (with IR cut filter)
................................SC83USB (with IR cut filter)
................................SC133USB (with IR cut filter)
................................................................................................
................................................................................................................................................................................................................................................................
................................................................
SBxxxUSB-BL) ................................................................................................................................................................
SBxxxUSB-AL) ................................
STC-SC133USB
................................................................
................................................................
................................................................................................................................................................................................
................................................................
................................................................
Electronic specifications / Mechanical specifications / Environmental specifications................................................................................................................................
................................
................................................................
................................................................
................................................................................................
................................................................................................
................................................................................................
................................................................................................
................................
................................................................
Mount, USB Angle / Straight) ................................Mount, USB Angle / Straight* )
BL (Color / Monochrome, Board type, No-Mount, USB Angle / Straight*)ype, Fixed Focus, USB Angle / Straight*) ................................
BLL (Monochrome, Board type, Fixed Focus, USB Angle / Straight*)AL (Color / Monochrome, Cased type, CS-Mount* )
................................................................
................................................................SC33USB (with IR cut filter) ................................
................................................................SC83USB (with IR cut filter) ................................
................................................................SC133USB (with IR cut filter) ................................
................................................................................................................................
................................................................................................................................
................................................................................................................................
................................
................................
................................................................
USB / STC-SB133USB
................................................................
................................................................................................................................
..............................................................................................................................
................................
................................
Electronic specifications / Mechanical specifications / Environmental specifications ................................................................................................
................................................................
................................................................
................................
................................................................................................
................................................................................................
................................................................................................
................................................................................................
................................................................
.............................................................
................................Mount, USB Angle / Straight* ) ................................
Mount, USB Angle / Straight*)................................
BLL (Monochrome, Board type, Fixed Focus, USB Angle / Straight*) ................................Mount* ) ................................
................................................................
..............................................................................................................................
..............................................................................................................................
............................................................................................................................
................................................................
................................................................................................................................................................................................................................................................
................................................................................................................................
................................................................
................................................................
................................................................................................................................
No.13S007
SB133USB
................................
..............................................................................
...................................................................................
.................................................................................................................
...........................................................
........................................................................................................................................................
..............................................
................................
...................................................
.........................................................................................
................................................................................
...................................................................................
...................................................................................................
................................
.............................
.................................................................................................
Mount, USB Angle / Straight*)......................................................
..........................................................................
................................
..............................................................
..............................................................
............................................................
..............................................................................................................
.........................................................................................................................................................................
................................................................
................................
................................
................................................................
No.13S007-07
3
.................................... 4
..................................... 4 .............. 4
..................... 5 .............................. 5 ............................. 5
.................... 5
........................... 6
................ 6 .................... 6 .................... 8
.............. 10
................................ 12
................... 13
....................................... 13 ......................... 13
................ 13 ....................................... 13
................... 13 .................................... 14
...................... 14 ............. 14
....................................... 15
............................. 16
........................ 16 ......... 17
Mount, USB Angle / Straight*) . 17 ...................... 18
.......... 18 .................................. 19
................................. 20
.............................. 4 ................................. 7
.............................. 7 ................................. 9
.............................. 9 .............................. 11
........................... 11 ................... 12
..................................... 12 ............... 13 .............. 14 ............ 15
.................................. 16 ................................. 17
..................................... 17
..................................... 18
..................................... 18 .................................... 19
STCSpecifications
1 OverviewThis document describes the specification of
1.1 Features
1.2 Specification of Naming
STC-SC33USBSpecifications
Overview This document describes the specification of
STC-SC33USB / SB33USB STC-SC83USB / SB83USB STC-SC133USB / SB133USB
Features ・Small Size・New camera r・Up to 64 pixel blemish static collection・8,10,12bit output(
These modelSTC-MC/MB**USB series).One board design can achieve such a drastically changing. the camera without needing to reseed the USB cable.various Lens Mountoutput(10,12bit work only on Trigger mode, or 1/2 clock free run mode. For data transfer bandwidth).
Specification of Naming
STC
SC33USB / STC-SB33USB
This document describes the specification of
SC33USB / SB33USB SC83USB / SB83USB SC133USB / SB133USB
Size New camera reset functionUp to 64 pixel blemish static collection8,10,12bit output(10,12bit work
These models of cameras are smaller and lower cost than another modelMB**USB series).One board design can achieve such a drastically changing.
the camera without needing to reseed the USB cable.various Lens Mounts.
(10,12bit work only on Trigger mode, or 1/2 clock free run mode. For data transfer bandwidth).
Specification of Naming
STC-SxxxxUSB
SB33USB / STC
This document describes the specification of
SC33USB / SB33USB SC83USB / SB83USB SC133USB / SB133USB
unction Up to 64 pixel blemish static collection
10,12bit work only on Trigger, or 1/2 clock free run mode)
of cameras are smaller and lower cost than another modelMB**USB series).One board design can achieve such a drastically changing.
the camera without needing to reseed the USB cable. Up to 64
(10,12bit work only on Trigger mode, or 1/2 clock free run mode. For data transfer bandwidth).
Specification of Naming
SxxxxUSB
STC-SC83USB
This document describes the specification of the following
(VGA) (XGA) (1.3M)
Up to 64 pixel blemish static collection only on Trigger, or 1/2 clock free run mode)
of cameras are smaller and lower cost than another modelMB**USB series).One board design can achieve such a drastically changing.
the camera without needing to reseed the USB cable.Up to 64 pixel blemish static
(10,12bit work only on Trigger mode, or 1/2 clock free run mode. For data transfer bandwidth).
SxxxxUSB-xxx
Figure
SC83USB / STC-SB83USB
the following cameras.
only on Trigger, or 1/2 clock free run mode)
of cameras are smaller and lower cost than another modelMB**USB series).One board design can achieve such a drastically changing.
the camera without needing to reseed the USB cable. These pixel blemish static collection is supported
(10,12bit work only on Trigger mode, or 1/2 clock free run mode. For data transfer bandwidth).
xxx
Figure 1. Naming Rule
SB83USB / STC
cameras.
only on Trigger, or 1/2 clock free run mode)
of cameras are smaller and lower cost than another modelMB**USB series).One board design can achieve such a drastically changing.
These models collection is supported
(10,12bit work only on Trigger mode, or 1/2 clock free run mode. For data transfer bandwidth).
Naming Rule
A: Case Type
B: Board Type
C: Color
B: Monochrome
Resolution
33: VGA
83: XGA
133:1.3M
L: USB “Light” angle connector
S: USB “Straight” angle connector only on
Board Type
Both model have Light angle IO connector
L: Micro Lens Mount
CS: CS Mount
None: Base Mount
STC-SC133USB
only on Trigger, or 1/2 clock free run mode)
of cameras are smaller and lower cost than another models(STCMB**USB series).One board design can achieve such a drastically changing.
of camerascollection is supported along with 8,10,12bit data
(10,12bit work only on Trigger mode, or 1/2 clock free run mode. For data transfer bandwidth).
A: Case Type
B: Board Type
C: Color
B: Monochrome
Resolution
33: VGA
83: XGA
133:1.3M
L: USB “Light” angle connector
S: USB “Straight” angle connector only on
Board Type
Both model have Light angle IO connector
L: Micro Lens Mount
CS: CS Mount
None: Base Mount
USB / STC-SB133USB
(STC-TC/TB**USBMB**USB series).One board design can achieve such a drastically changing. The port can now reset
s have Color/Monochrome, along with 8,10,12bit data
(10,12bit work only on Trigger mode, or 1/2 clock free run mode. For data transfer bandwidth).
L: USB “Light” angle connector
S: USB “Straight” angle connector only on
Both model have Light angle IO connector
L: Micro Lens Mount
No.13S007
SB133USB
TC/TB**USB-B seriesThe port can now reset
have Color/Monochrome, along with 8,10,12bit data
(10,12bit work only on Trigger mode, or 1/2 clock free run mode. For data transfer bandwidth).
L: USB “Light” angle connector
S: USB “Straight” angle connector only on
Both model have Light angle IO connector
No.13S007-07
4
B series・The port can now reset
have Color/Monochrome, along with 8,10,12bit data
S: USB “Straight” angle connector only on
Both model have Light angle IO connector
STCSpecifications
1.3 Support Application
1.4 Option model
1.5 Power Supply
1.6 Pixel Blemish Static Collection and
STC-SC33USBSpecifications
Support Application
These models work on Sentech’s viewing software(StCamSWare) ,SDSK(TriggerSDK,StandardSDK) and samle codes. Some part of functions are not same as another modelSTC-MC/MB**USB series).When user use the camera, please pay attention to the difference.
e.g. � LED � Two IO work� Product ID
through
Option modelSentech sales representative on user’s area.
Power SupplySentech recommend to use the STC-SC33USB/STC
Pixel Blemish Static Collection and
These modelthe factory setting “StCamSWare_v**_Manual_EN
USB port power cable
SC33USB / STC-SB33USB
Support Application
These models work on Sentech’s viewing software(StCamSWare) ,SDSK(TriggerSDK,StandardSDK) and samle codes. Some part of functions are not same as another model
MC/MB**USB series).When user use the camera, please pay attention to the difference.
LED does not Two IO works on theseProduct ID can be known throughthrough StCam_GetProductNam
Option model could provide the option model that does not mention on this document. As for the detail, please ask the
sales representative on user’s area.
Power Supply Sentech recommend to use the
SC33USB/STC-
Pixel Blemish Static Collection and models have pixel blemish static collection and saving camera settings on the camera. User can recover to
the factory setting and save the camera setting on PC StCamSWare_v**_Manual_EN
USB port power cable
SB33USB / STC
These models work on Sentech’s viewing software(StCamSWare) ,SDSK(TriggerSDK,StandardSDK) and samle codes. Some part of functions are not same as another model
MC/MB**USB series).When user use the camera, please pay attention to the difference.
does not work on sample codes on these model
can be known throughStCam_GetProductNam
could provide the option model that does not mention on this document. As for the detail, please ask the sales representative on user’s area.
Sentech recommend to use the -SB33USB. For the out of range on USB specification of current consumption
Pixel Blemish Static Collection and have pixel blemish static collection and saving camera settings on the camera. User can recover to
and save the camera setting on PC StCamSWare_v**_Manual_EN”.
USB port power cable
STC-SC83USB
These models work on Sentech’s viewing software(StCamSWare) ,SDSK(TriggerSDK,StandardSDK) and samle codes. Some part of functions are not same as another model
MC/MB**USB series).When user use the camera, please pay attention to the difference.
work on sample code (StTrgDisplayVC2005.exe)models, even Sentech’s viewing software(StCamSWare) show four IO.
can be known through StCam_GetProductNam StCam_GetProductNam.
could provide the option model that does not mention on this document. As for the detail, please ask the sales representative on user’s area.
Sentech recommend to use the USB port power cable when use uses 90fps with partial (or binning) modSB33USB. For the out of range on USB specification of current consumption
Pixel Blemish Static Collection and Saving Camera Settingshave pixel blemish static collection and saving camera settings on the camera. User can recover to
and save the camera setting on PC ”.
SC83USB / STC-SB83USB
These models work on Sentech’s viewing software(StCamSWare) ,SDSK(TriggerSDK,StandardSDK) and samle codes. Some part of functions are not same as another model
MC/MB**USB series).When user use the camera, please pay attention to the difference.
(StTrgDisplayVC2005.exe)even Sentech’s viewing software(StCamSWare) show four IO.
StCam_GetProductNam
could provide the option model that does not mention on this document. As for the detail, please ask the
USB port power cable when use uses 90fps with partial (or binning) modSB33USB. For the out of range on USB specification of current consumption
Saving Camera Settingshave pixel blemish static collection and saving camera settings on the camera. User can recover to
and save the camera setting on PC
SB83USB / STC
These models work on Sentech’s viewing software(StCamSWare) ,SDSK(TriggerSDK,StandardSDK) and samle codes. Some part of functions are not same as another model
MC/MB**USB series).When user use the camera, please pay attention to the difference.
(StTrgDisplayVC2005.exe)even Sentech’s viewing software(StCamSWare) show four IO.
StCam_GetProductNam on
could provide the option model that does not mention on this document. As for the detail, please ask the
USB port power cable when use uses 90fps with partial (or binning) modSB33USB. For the out of range on USB specification of current consumption
Saving Camera Settings have pixel blemish static collection and saving camera settings on the camera. User can recover to
and save the camera setting on PC also. As for the detail, please see the user’s guide of
STC-SC133USB
These models work on Sentech’s viewing software(StCamSWare) ,SDSK(TriggerSDK,StandardSDK) and samle codes. Some part of functions are not same as another models(STC
MC/MB**USB series).When user use the camera, please pay attention to the difference.
(StTrgDisplayVC2005.exe). even Sentech’s viewing software(StCamSWare) show four IO.
on SDK. However it can be obtained
could provide the option model that does not mention on this document. As for the detail, please ask the
USB port power cable when use uses 90fps with partial (or binning) modSB33USB. For the out of range on USB specification of current consumption
have pixel blemish static collection and saving camera settings on the camera. User can recover to also. As for the detail, please see the user’s guide of
USB / STC-SB133USB
These models work on Sentech’s viewing software(StCamSWare) ,SDSK(TriggerSDK,StandardSDK) and (STC-TC/TB**USB
MC/MB**USB series).When user use the camera, please pay attention to the difference.
even Sentech’s viewing software(StCamSWare) show four IO.. However it can be obtained
could provide the option model that does not mention on this document. As for the detail, please ask the
USB port power cable when use uses 90fps with partial (or binning) modSB33USB. For the out of range on USB specification of current consumption
have pixel blemish static collection and saving camera settings on the camera. User can recover to also. As for the detail, please see the user’s guide of
No.13S007
SB133USB
These models work on Sentech’s viewing software(StCamSWare) ,SDSK(TriggerSDK,StandardSDK) and TC/TB**USB-B series
even Sentech’s viewing software(StCamSWare) show four IO. . However it can be obtained
could provide the option model that does not mention on this document. As for the detail, please ask the
USB port power cable when use uses 90fps with partial (or binning) modSB33USB. For the out of range on USB specification of current consumption.
have pixel blemish static collection and saving camera settings on the camera. User can recover to also. As for the detail, please see the user’s guide of
No.13S007-07
5
These models work on Sentech’s viewing software(StCamSWare) ,SDSK(TriggerSDK,StandardSDK) and B series・
could provide the option model that does not mention on this document. As for the detail, please ask the
USB port power cable when use uses 90fps with partial (or binning) mode on
have pixel blemish static collection and saving camera settings on the camera. User can recover to also. As for the detail, please see the user’s guide of
STCSpecifications
2 Specifications2.1 Electronic specifications / Mechanical specifications / Environmental specifications
Product
ElectronicSpecifications
MechanicalSpecifications
EnvironmentalSpecifications
STC-SC33USBSpecifications
SpecificationsElectronic specifications / Mechanical specifications / Environmental specifications
2.1.1 STC
Table 1. Specifications of STC
Gain
Product
ElectronicSpecificatio
Image Sensor
Resolution
Scanning methods
Maximumframer rate
Pixel frequency
White balanceTrigger mode
Gamma
Video outputMinimum scene illumination *Note2
Sync. SystemElectronic shutter
Camera ResetLED StatusPixel Blemish Correction Input/output
MechanicalSpecificatio
DimensionsLens mount
WeightInterfaceconnector
Power
RoHS
Environmen
Specificatio
Operational temperatureStorage temperatureVibration *Note4
Shock *Note4Standard compliancy
SC33USB / STC-SB33USB
Specifications Electronic specifications / Mechanical specifications / Environmental specifications
STC-SC33USB / STC
Specifications of STC
Total picture elementsEffective picture elementsChip sizeCell sizeScanning system
Full scanning1/2 partial scanning1/4 partial scanning
Normal1/2 clock1/4 clock
Input voltageConsumption
Image Sensor
Scanning methods
Pixel frequency
White balanceTrigger mode
Video outputMinimum scene illumination *Note2
Sync. SystemElectronic shutter
Camera ResetLED StatusPixel Blemish Correction Input/output
DimensionsLens mount
Angle
Operational temperatureStorage temperatureVibration *Note4
Shock *Note4Standard compliancy
SB33USB / STC
Electronic specifications / Mechanical specifications / Environmental specifications
SC33USB / STC-SB33USB
Specifications of STC-SC33USB / STC
Total picture elementsEffective picture elements
Scanning system
1/2 partial scanning1/4 partial scanning
Minimum scene illumination *Note2
STC-SC83USB
Electronic specifications / Mechanical specifications / Environmental specifications
SB33USB
SC33USB / STC
STC-SC33USB1/3" interline VGA color progressive CCD:
ICX424AQ(Sony)
1/1 partial scanning,1/2 partial scanning,1/4 partial scanning,
Variable partial scanning
Auto / Manual / One shot (software selectable)
59.94 fps (Normal) /
120.11 fps (Normal) / 60.05 fsp (1/2clock) / 30.02 fps (1/4clock) / 180.165 fps (3/2clock)
240.22 fps (Normal) / 120.11 fps (1/2clock) / 60.055 fps (1/4clock) / 360.33 fps (3/2clock)
24.5454 MHz (Normal) / 12.2727 MHz (1/2clock) / 6.13635 MHz (1/4clock) / 36.818 MHz (3/2clock)
Free-run / Edge preset trigger / Pulse width trigger / Start & stop trigger (software selectable)
20Hz to 200Hz to 20Hz (5min./cycle), acccelaration 10G, 3 directions 30 min. each
SC83USB / STC-SB83USB
Electronic specifications / Mechanical specifications / Environmental specifications
SC33USB / STC-SB33USB
STC-SC33USB1/3" interline VGA color progressive CCD:
ICX424AQ(Sony)
Full scanning,1/1 partial scanning,1/2 partial scanning,1/4 partial scanning,
Variable partial scanning
7.14lx at F1.2
/ Manual / One shot (software selectable)
59.94 fps (Normal) / 29.97 fps (1/2clock)
120.11 fps (Normal) / 60.05 fsp (1/2clock) / 30.02 fps (1/4clock) / 180.165 fps (3/2clock)
240.22 fps (Normal) / 120.11 fps (1/2clock) / 60.055 fps (1/4clock) / 360.33 fps (3/2clock)
Auto /
24.5454 MHz (Normal) / 12.2727 MHz (1/2clock) / 6.13635 MHz (1/4clock) / 36.818 MHz (3/2clock)
/ Edge preset trigger / Pulse width trigger / Start & stop trigger (software selectable)(Hardware trigger and Software tigger are available)
1/100,000 to 1/22.40 seconds(default 1/29.18 seconds)
Green(Flicker):Power-On, Green:Camera works
Board Type::36(W) x 36(H) x 15.3(D) CS-Mount(without USB connector)CS mount / MicroLens Mount (M12 P0.5) / None Mount
IO Connector
+5 V through USB connector (+4.4 to +5.25V)
Case Type: EMS: EN61000-6-2, EMI: EN55011
20Hz to 200Hz to 20Hz (5min./cycle), acccelaration 10G, 3 directions 30 min. eachAccelaration 70G, half amplitude 6ms, 3 directions 3 times each
SB83USB / STC
Electronic specifications / Mechanical specifications / Environmental specifications
SB33USB
1/3" interline VGA color progressive CCD: ICX424AQ(Sony)
1/1 partial scanning,1/2 partial scanning,1/4 partial scanning,
Variable partial scanning
/ Manual / One shot (software selectable)
29.97 fps (1/2clock) / 14.98 fps (1/4clock) / 89.91 fps (3/2clock) *Note1
120.11 fps (Normal) / 60.05 fsp (1/2clock) / 30.02 fps (1/4clock) / 180.165 fps (3/2clock)
240.22 fps (Normal) / 120.11 fps (1/2clock) / 60.055 fps (1/4clock) / 360.33 fps (3/2clock)
1/100,000 to 1/5.60 secondsAuto / Manual (software selectable,
24.5454 MHz (Normal) / 12.2727 MHz (1/2clock) / 6.13635 MHz (1/4clock) / 36.818 MHz (3/2clock)
692(H) x 504(V)
659(H) x 494(V)
5.79(H) x 4.89(V) mm
7.40(H) x 7.40(V) μm
Progressive
640(H) x 480(V) (Full scanning)640(H) x 224(V) (1/2 partial scanning)640(H) x 80(V) (1/4 partial scanning)
/ Edge preset trigger / Pulse width trigger / Start & stop trigger (software selectable)(Hardware trigger and Software tigger are available)
Manual (software selectable,
8bit / 10bit /12bit *Note2
InternalAuto / Manual
1/100,000 to 1/22.40 seconds(default 1/29.18 seconds)1/100,000 to 1/11.20 seconds
Support on Pin 5Green(Flicker):Power-On, Green:Camera works
64 Points (default:off)USB2.0 High speed
Board Type::36(W) x 36(H) x 15.3(D) CS-Mount(without USB connector)CS mount / MicroLens Mount (M12 P0.5) / None Mount
approximately 15gUSB: mini-B USB connector
IO Connector :SM05B-SRSS-TB (JST) 5pin
+5 V through USB connector (+4.4 to +5.25V)less than 2.0 W *Note3
Case Type: EMS: EN61000-6-2, EMI: EN55011RoHS compliance
0 to 40 deg. C-30 to 65 deg. C
20Hz to 200Hz to 20Hz (5min./cycle), acccelaration 10G, 3 directions 30 min. eachAccelaration 70G, half amplitude 6ms, 3 directions 3 times each
STC-SC133USB
Electronic specifications / Mechanical specifications / Environmental specifications
1/3" interline VGA monochrome progressive CCD:
Binning variable partial scanning
/ 14.98 fps (1/4clock) / 89.91 fps (3/2clock) *Note1
120.11 fps (Normal) / 60.05 fsp (1/2clock) / 30.02 fps (1/4clock) / 180.165 fps (3/2clock)
240.22 fps (Normal) / 120.11 fps (1/2clock) / 60.055 fps (1/4clock) / 360.33 fps (3/2clock)
1/100,000 to 1/5.60 seconds (software selectable,default: x3.55
24.5454 MHz (Normal) / 12.2727 MHz (1/2clock) / 6.13635 MHz (1/4clock) / 36.818 MHz (3/2clock)
692(H) x 504(V)
659(H) x 494(V)
5.79(H) x 4.89(V) mm
7.40(H) x 7.40(V) μm
Progressive
640(H) x 480(V) (Full scanning)640(H) x 224(V) (1/2 partial scanning)640(H) x 80(V) (1/4 partial scanning)
/ Edge preset trigger / Pulse width trigger / Start & stop trigger (software selectable)(Hardware trigger and Software tigger are available)
Manual (software selectable,default: 1
/ 10bit /12bit *Note2
InternalManual (software selectable)
1/100,000 to 1/22.40 seconds(default 1/29.18 seconds)1/100,000 to 1/11.20 seconds
Support on Pin 5Green(Flicker):Power-On, Green:Camera works
64 Points (default:off)USB2.0 High speed
Board Type::36(W) x 36(H) x 15.3(D) CS-Mount(without USB connector)CS mount / MicroLens Mount (M12 P0.5) / None Mount
approximately 15gUSB: mini-B USB connector
SM05B-SRSS-TB (JST) 5pin
+5 V through USB connector (+4.4 to +5.25V)less than 2.0 W *Note3
Case Type: EMS: EN61000-6-2, EMI: EN55011RoHS compliance
0 to 40 deg. C-30 to 65 deg. C
20Hz to 200Hz to 20Hz (5min./cycle), acccelaration 10G, 3 directions 30 min. eachAccelaration 70G, half amplitude 6ms, 3 directions 3 times each
USB / STC-SB133USB
Electronic specifications / Mechanical specifications / Environmental specifications
Bold: Initial ValueSTC-SB33USB
1/3" interline VGA monochrome progressive CCD: ICX424AL(Sony)
Full scanning,1/1 partial scanning,1/2 partial scanning,1/4 partial scanning,
Variable partial scanning,Binning scanning,
Binning 1/1 partial scanning,Binning 1/2 partial scanning,Binning 1/4 partial scanning,
Binning variable partial scanning
0.07lx at F1.2
-
/ 14.98 fps (1/4clock) / 89.91 fps (3/2clock) *Note1
120.11 fps (Normal) / 60.05 fsp (1/2clock) / 30.02 fps (1/4clock) / 180.165 fps (3/2clock)
240.22 fps (Normal) / 120.11 fps (1/2clock) / 60.055 fps (1/4clock) / 360.33 fps (3/2clock)
1/100,000 to 1/5.60 secondsdefault: x3.55)
24.5454 MHz (Normal) / 12.2727 MHz (1/2clock) / 6.13635 MHz (1/4clock) / 36.818 MHz (3/2clock)
640(H) x 480(V) (Full scanning)640(H) x 224(V) (1/2 partial scanning)640(H) x 80(V) (1/4 partial scanning)
/ Edge preset trigger / Pulse width trigger / Start & stop trigger (software selectable)(Hardware trigger and Software tigger are available)
default: 1)
(software selectable)1/100,000 to 1/22.40 seconds(default 1/29.18 seconds)
1/100,000 to 1/11.20 seconds
Green(Flicker):Power-On, Green:Camera works
Board Type::36(W) x 36(H) x 15.3(D) CS-Mount(without USB connector)CS mount / MicroLens Mount (M12 P0.5) / None Mount
USB: mini-B USB connectorSM05B-SRSS-TB (JST) 5pin
+5 V through USB connector (+4.4 to +5.25V)
Case Type: EMS: EN61000-6-2, EMI: EN55011
20Hz to 200Hz to 20Hz (5min./cycle), acccelaration 10G, 3 directions 30 min. eachAccelaration 70G, half amplitude 6ms, 3 directions 3 times each
No.13S007
SB133USB
Bold: Initial ValueSTC-SB33USB
1/3" interline VGA monochrome progressive CCD: ICX424AL(Sony)
Full scanning,1/1 partial scanning,1/2 partial scanning,1/4 partial scanning,
Variable partial scanning,Binning scanning,
Binning 1/1 partial scanning,Binning 1/2 partial scanning,Binning 1/4 partial scanning,
Binning variable partial scanning
0.07lx at F1.2
/ 14.98 fps (1/4clock) / 89.91 fps (3/2clock) *Note1
120.11 fps (Normal) / 60.05 fsp (1/2clock) / 30.02 fps (1/4clock) / 180.165 fps (3/2clock)
240.22 fps (Normal) / 120.11 fps (1/2clock) / 60.055 fps (1/4clock) / 360.33 fps (3/2clock)
24.5454 MHz (Normal) / 12.2727 MHz (1/2clock) / 6.13635 MHz (1/4clock) / 36.818 MHz (3/2clock)
/ Edge preset trigger / Pulse width trigger / Start & stop trigger (software selectable)
Board Type::36(W) x 36(H) x 15.3(D) CS-Mount(without USB connector)
20Hz to 200Hz to 20Hz (5min./cycle), acccelaration 10G, 3 directions 30 min. eachAccelaration 70G, half amplitude 6ms, 3 directions 3 times each
No.13S007-07
6
Bold: Initial Value
1/3" interline VGA monochrome progressive CCD:
/ 14.98 fps (1/4clock) / 89.91 fps (3/2clock) *Note1
24.5454 MHz (Normal) / 12.2727 MHz (1/2clock) / 6.13635 MHz (1/4clock) / 36.818 MHz (3/2clock)
/ Edge preset trigger / Pulse width trigger / Start & stop trigger (software selectable)
STCSpecifications
*Note1: *Note*Note*Note
Spect
STC-SC33USBSpecifications
*Note1: [Default setting of Maximum Frame Rate] Bold*Note2: As for the 10,12bit output, clock speed should be slow to obtain the correct frame rate.*Note3: Power *Note4: Lens: COSMICAR/PENTAX,
Spectral Sensitivity Characteristics
STC
STC
SC33USB / STC-SB33USB
[Default setting of Maximum Frame Rate]Bold: On Sentech Viewing software
: As for the 10,12bit output, clock speed should be slow to obtain the correct frame rate.: Power consumptionLens: COSMICAR/PENTAX,
ral Sensitivity CharacteristicsSTC-SC33USB (with IR cut filter)
Figure 2.Spectral Sensitivity Characteristics on STC
STC-SB33USB
Figure
1
0.8
0.4
0.6
0.2
0400
Rel
ativ
e R
espo
nse
1
0.8
0.4
0.6
0.2
0400
Rel
ativ
e R
espo
nse
SB33USB / STC
[Default setting of Maximum Frame Rate]: On Sentech Viewing software
: As for the 10,12bit output, clock speed should be slow to obtain the correct frame rate.consumption could be higher than this number under 90fps with
Lens: COSMICAR/PENTAX, C1614
ral Sensitivity Characteristics(with IR cut filter)
.Spectral Sensitivity Characteristics on STC
Figure 3.Spectral Sensitivity Characteristics on STC
400
500
STC-SC83USB
[Default setting of Maximum Frame Rate] : On Sentech Viewing software (StcamSWare), Normal: Another condition
: As for the 10,12bit output, clock speed should be slow to obtain the correct frame rate.could be higher than this number under 90fps with
C1614-M with C
ral Sensitivity Characteristics (with IR cut filter)
.Spectral Sensitivity Characteristics on STC
.Spectral Sensitivity Characteristics on STC
500
B
600
SC83USB / STC-SB83USB
(StcamSWare), Normal: Another condition
: As for the 10,12bit output, clock speed should be slow to obtain the correct frame rate.could be higher than this number under 90fps with
M with C-Adaptor
.Spectral Sensitivity Characteristics on STC
.Spectral Sensitivity Characteristics on STC
Wave length [nm]
G
700Wave length [nm]
SB83USB / STC
(StcamSWare), Normal: Another condition: As for the 10,12bit output, clock speed should be slow to obtain the correct frame rate.
could be higher than this number under 90fps with Adaptor
.Spectral Sensitivity Characteristics on STC-SC33USB (with IR cut filter)
.Spectral Sensitivity Characteristics on STC
600Wave length [nm]
R
IR cut filter
800Wave length [nm]
STC-SC133USB
(StcamSWare), Normal: Another condition: As for the 10,12bit output, clock speed should be slow to obtain the correct frame rate.
could be higher than this number under 90fps with partial scan
SC33USB (with IR cut filter)
.Spectral Sensitivity Characteristics on STC-SB33USB
R
IR cut filter
900
USB / STC-SB133USB
(StcamSWare), Normal: Another condition : As for the 10,12bit output, clock speed should be slow to obtain the correct frame rate.
scan.
SC33USB (with IR cut filter)
SB33USB
700
1000
No.13S007
SB133USB
SC33USB (with IR cut filter)
No.13S007-07
7
STCSpecifications
*Note1: As for the 10,12bit output, clock speed should be slow to obtain the correct frame rate.*Note2: Lens: COSMICAR/PENTAX,
ProductElectronicSpecifications
MechanicalSpecifications
EnvironmentalSpecifications
STC-SC33USBSpecifications
2.1.2 STC
Table 2. Specifications of STC
*Note1: As for the 10,12bit output, clock speed should be slow to obtain the correct frame rate.*Note2: Lens: COSMICAR/PENTAX,
ProductElectronicSpecifications
Video output
Dimensions
White balance
Camera Reset
Image Sensor
LED Status
Trigger mode
Input/output
GainGamma
Resolution
Scanning methods
Maximumframer rate
Sync. SystemMinimum scene illumination
Operational temperature
Pixel Blemish Correction
Power
Electronic shutter
Pixel frequency
MechanicalSpecifications Lens mount
Interfaceconnector
Weight
EnvironmentalSpecifications Storage temperature
RoHS
Vibration *Note2Shock *Note2Standard compliancy
SC33USB / STC-SB33USB
STC-SC83USB / STC
. Specifications of STC
*Note1: As for the 10,12bit output, clock speed should be slow to obtain the correct frame rate.*Note2: Lens: COSMICAR/PENTAX,
Total picture elementsEffective picture elementsChip sizeCell sizeScanning system
Full scanning1/2 partial scanning1/4 partial scanning
Normal1/2 clock1/4 clock
Input voltageConsumption
Video output
Dimensions
White balance
Camera Reset
Image Sensor
LED Status
Trigger mode
Input/output
GainGamma
Resolution
Scanning methods
Maximumframer rate
Sync. SystemMinimum scene illumination
Operational temperature
Pixel Blemish Correction
Power
Electronic shutter
Pixel frequency
Lens mount
Interfaceconnector
Angle
Weight
Storage temperature
RoHS
Vibration *Note2Shock *Note2Standard compliancy
SB33USB / STC
SC83USB / STC-SB83USB
. Specifications of STC-SC83USB / STC
*Note1: As for the 10,12bit output, clock speed should be slow to obtain the correct frame rate.*Note2: Lens: COSMICAR/PENTAX, C1614
Total picture elementsEffective picture elementsChip sizeCell sizeScanning system
Full scanning1/2 partial scanning1/4 partial scanning
Normal1/2 clock1/4 clock
Input voltageConsumption
Minimum scene illumination
Operational temperature
Pixel Blemish Correction
Angle
STC-SC83USB
SB83USB
SC83USB / STC
*Note1: As for the 10,12bit output, clock speed should be slow to obtain the correct frame rate.C1614-M with C
1/3" interline XGA color progressive CCD:
Effective picture elements
Auto / Manual / One shot (software selectable)Free-run
SC83USB / STC-SB83USB
SC83USB / STC-SB83USB
*Note1: As for the 10,12bit output, clock speed should be slow to obtain the correct frame rate.M with C-Adaptor
STC-SC83USB1/3" interline XGA color progressive CCD:
ICX204AK (Sony)
Full scanning,1/1 partial scanning,1/2 partial scanning,1/4 partial scanning,
Variable partial scanning
16.54lx at F1.2
/ Manual / One shot (software selectable)
Board Type::36(W) x 36(H) x 15.3(D) CS-Mount(without USB connector)
Free-run / Edge preset trigger / Pulse width trigger / Start & stop trigger (software selectable)
Auto /
CS mount / MicroLens Mount (M12 P0.5) / None Mount
1/100,000 to 1/22.40 seconds(default 1/29.18 seconds)
29.18 fps 60.02 fps (Normal) / 30.01 fps (1/2 clock) / 15.00 fps (1/4 clock)
29.5 MHz (Normal) / 14.75 MHz (1/2 clock) / 7.375 MHz (1/4 clock)120.35 fps (Normal) / 60.175 fps (1/2 clock) / 30.087 fps (1/4 clock)
20Hz to 200Hz to 20Hz (5min./cycle), acccelaration 10G, 3 directions 30 min. eachAccelaration 70G, half amplitude 6ms, 3 directions 3 times each
SB83USB / STC
SB83USB
*Note1: As for the 10,12bit output, clock speed should be slow to obtain the correct frame rate.Adaptor
STC-SC83USB1/3" interline XGA color progressive CCD:
ICX204AK (Sony)
Full scanning,1/1 partial scanning,1/2 partial scanning,1/4 partial scanning,
Variable partial scanning
16.54lx at F1.2
/ Manual / One shot (software selectable)
8bit / 10bit / 12bit *Note1
(Hardware trigger and Software tigger are available)
Board Type::36(W) x 36(H) x 15.3(D) CS-Mount(without USB connector)
/ Edge preset trigger / Pulse width trigger / Start & stop trigger (software selectable)
+5 V through USB connector (+4.4 to +5.25V)
Green(Flicker):Power-On, Green:Camera works
1024 (H) x 768 (V) (Full scanning)1024 (H) x 344 (V) (1/2 partial scanning)1024 (H) x 136 (V) (1/4 partial scanning)
1077 (H) x 788 (V)
4.65 (H) x 4.65 (V)
1034 (H) x 779 (V)
Auto / Manual (software selectable,
Approximately 15g
Less than 1.4W
USB2.0 High speed
CS mount / MicroLens Mount (M12 P0.5) / None Mount
Manual (software selectable,
0 to 40 deg. CIO Connector :SM05B-SRSS-TB (JST) 5pin
USB: mini-B USB connector
Support on Pin 5
1/100,000 to 1/22.40 seconds(default 1/29.18 seconds)1/100,000 to 1/11.20 seconds1/100,000 to 1/5.60 seconds
RoHS compliance
5.80 (H) x 4.92 (V) mm
Progressive
29.18 fps (Normal) / 14.59 fps (1/2 clock) / 7.295 fps (1/4 clock)60.02 fps (Normal) / 30.01 fps (1/2 clock) / 15.00 fps (1/4 clock)
29.5 MHz (Normal) / 14.75 MHz (1/2 clock) / 7.375 MHz (1/4 clock)120.35 fps (Normal) / 60.175 fps (1/2 clock) / 30.087 fps (1/4 clock)
Auto / Manual
-30 to 65 deg. C20Hz to 200Hz to 20Hz (5min./cycle), acccelaration 10G, 3 directions 30 min. each
Accelaration 70G, half amplitude 6ms, 3 directions 3 times eachCase Type: EMS: EN61000-6-2, EMI: EN55011
STC-SC133USB
*Note1: As for the 10,12bit output, clock speed should be slow to obtain the correct frame rate.
1/3" interline XGA monochrome progressive CCD:
Binning variable partial scanning
/ 10bit / 12bit *Note1
(Hardware trigger and Software tigger are available)
Board Type::36(W) x 36(H) x 15.3(D) CS-Mount(without USB connector)
/ Edge preset trigger / Pulse width trigger / Start & stop trigger (software selectable)
+5 V through USB connector (+4.4 to +5.25V)
Green(Flicker):Power-On, Green:Camera works
1024 (H) x 768 (V) (Full scanning)1024 (H) x 344 (V) (1/2 partial scanning)1024 (H) x 136 (V) (1/4 partial scanning)
1077 (H) x 788 (V)
4.65 (H) x 4.65 (V) μm
1034 (H) x 779 (V)
(software selectable,default: x3.55
Approximately 15g
Less than 1.4W
USB2.0 High speed
CS mount / MicroLens Mount (M12 P0.5) / None Mount
Manual (software selectable,default: 1
0 to 40 deg. CSM05B-SRSS-TB (JST) 5pin
USB: mini-B USB connector
64 Points
Support on Pin 5
Internal
1/100,000 to 1/22.40 seconds(default 1/29.18 seconds)1/100,000 to 1/11.20 seconds1/100,000 to 1/5.60 seconds
RoHS compliance
5.80 (H) x 4.92 (V) mm
Progressive
(Normal) / 14.59 fps (1/2 clock) / 7.295 fps (1/4 clock)60.02 fps (Normal) / 30.01 fps (1/2 clock) / 15.00 fps (1/4 clock)
29.5 MHz (Normal) / 14.75 MHz (1/2 clock) / 7.375 MHz (1/4 clock)120.35 fps (Normal) / 60.175 fps (1/2 clock) / 30.087 fps (1/4 clock)
Manual (software selectable)
-30 to 65 deg. C20Hz to 200Hz to 20Hz (5min./cycle), acccelaration 10G, 3 directions 30 min. each
Accelaration 70G, half amplitude 6ms, 3 directions 3 times eachCase Type: EMS: EN61000-6-2, EMI: EN55011
USB / STC-SB133USB
Bold: Initial Value
*Note1: As for the 10,12bit output, clock speed should be slow to obtain the correct frame rate.
STC-SB83USB1/3" interline XGA monochrome progressive CCD:
ICX204AL (Sony)
Full scanning,1/1 partial scanning,1/2 partial scanning,1/4 partial scanning,
Variable partial scanning,Binning scanning,
Binning 1/1 partial scanning,Binning 1/2 partial scanning,Binning 1/4 partial scanning,
Binning variable partial scanning
0.31lx at F1.2
-
(Hardware trigger and Software tigger are available)
Board Type::36(W) x 36(H) x 15.3(D) CS-Mount(without USB connector)
/ Edge preset trigger / Pulse width trigger / Start & stop trigger (software selectable)
+5 V through USB connector (+4.4 to +5.25V)
Green(Flicker):Power-On, Green:Camera works
1024 (H) x 768 (V) (Full scanning)1024 (H) x 344 (V) (1/2 partial scanning)1024 (H) x 136 (V) (1/4 partial scanning)
default: x3.55)
CS mount / MicroLens Mount (M12 P0.5) / None Mount
default: 1)
SM05B-SRSS-TB (JST) 5pin
1/100,000 to 1/22.40 seconds(default 1/29.18 seconds)
(Normal) / 14.59 fps (1/2 clock) / 7.295 fps (1/4 clock)60.02 fps (Normal) / 30.01 fps (1/2 clock) / 15.00 fps (1/4 clock)
29.5 MHz (Normal) / 14.75 MHz (1/2 clock) / 7.375 MHz (1/4 clock)120.35 fps (Normal) / 60.175 fps (1/2 clock) / 30.087 fps (1/4 clock)
(software selectable)
20Hz to 200Hz to 20Hz (5min./cycle), acccelaration 10G, 3 directions 30 min. eachAccelaration 70G, half amplitude 6ms, 3 directions 3 times each
Case Type: EMS: EN61000-6-2, EMI: EN55011
No.13S007
SB133USB
Bold: Initial ValueSTC-SB83USB
1/3" interline XGA monochrome progressive CCD:ICX204AL (Sony)
Full scanning,1/1 partial scanning,1/2 partial scanning,1/4 partial scanning,
Variable partial scanning,Binning scanning,
Binning 1/1 partial scanning,Binning 1/2 partial scanning,Binning 1/4 partial scanning,
Binning variable partial scanning
0.31lx at F1.2
/ Edge preset trigger / Pulse width trigger / Start & stop trigger (software selectable)
20Hz to 200Hz to 20Hz (5min./cycle), acccelaration 10G, 3 directions 30 min. each
No.13S007-07
8
Bold: Initial Value
STCSpecifications
Spectral Sensitivity
STC-SC33USBSpecifications
Spectral Sensitivity
STC
STC
1
0.8
0.4
0.6
0.2
0
Rel
ativ
e R
espo
nse
SC33USB / STC-SB33USB
Spectral Sensitivity
STC-SC83USB (with IR cut filter)
Figure 4.Spectral Sensitivity Characteristics on STC
STC-SB83USB
Figure
1
0.8
0.4
0.6
0.2
0400
1
0.8
0.4
0.6
0.2
0400
Rel
ativ
e R
espo
nse
SB33USB / STC
Spectral Sensitivity Characteristics
(with IR cut filter)
.Spectral Sensitivity Characteristics on STC
Figure 5.Spectral Sensitivity Characteristics on STC
500
400
STC-SC83USB
Characteristics
(with IR cut filter)
.Spectral Sensitivity Characteristics on STC
.Spectral Sensitivity Characteristics on STC
600
500
B
SC83USB / STC-SB83USB
.Spectral Sensitivity Characteristics on STC
.Spectral Sensitivity Characteristics on STC
700Wave length [nm]
Wave length [nm]
G
SB83USB / STC
.Spectral Sensitivity Characteristics on STC-SC83USB (with IR cut filter)
.Spectral Sensitivity Characteristics on STC
800Wave length [nm]
600Wave length [nm]
IR cut filter
STC-SC133USB
SC83USB (with IR cut filter)
.Spectral Sensitivity Characteristics on STC-SB83USB
800
R
IR cut filter
USB / STC-SB133USB
SC83USB (with IR cut filter)
SB83USB
900
700
No.13S007
SB133USB
SC83USB (with IR cut filter)
1000
No.13S007-07
9
STCSpecifications
*Note1: As for the 10,12bit output, clock speed should be slow to obtain the correct frame rate.*Note2: Lens: COSMICAR/PENTAX,
STC-SC33USBSpecifications
2.1.3 STC
Table 3.Specifications of
*Note1: As for the 10,12bit output, clock speed should be slow to obtain the correct frame rate.*Note2: Lens: COSMICAR/PENTAX,
Product
EnvironmentalSpecifications
MechanicalSpecifications
ElectronicSpecifications
SC33USB / STC-SB33USB
STC-SC133USB / STC
.Specifications of
*Note1: As for the 10,12bit output, clock speed should be slow to obtain the correct frame rate.*Note2: Lens: COSMICAR/PENTAX,
Total picture elementsEffective picture elementsChip sizeCell sizeScanning system
Full scanning1/2 partial scanning1/4 partial scanning
Normal1/2 clock1/4 clock
Input voltageConsumption
Input/output
White balanceGammaGain
Minimum scene illumination *Note2
Resolution
Camera Reset
Pixel Blemish Correction
Image Sensor
Video output
Scanning methods
Maximumframer rate
Sync. System
Operational temperature
Weight
Storage temperature
RoHS
Trigger mode
Lens mount
Interfaceconnector
Angle
Dimensions
Pixel frequency
Electronic shutter
Standard compliancy
Power
Vibration *Note2Shock *Note2
LED Status
SB33USB / STC
SC133USB / STC-SB133USB
.Specifications of STC-SC133USB / STC
*Note1: As for the 10,12bit output, clock speed should be slow to obtain the correct frame rate.*Note2: Lens: COSMICAR/PENTAX, C1614
Total picture elementsEffective picture elementsChip sizeCell sizeScanning system
Full scanning1/2 partial scanning1/4 partial scanning
Normal1/2 clock1/4 clock
Input voltageConsumption
Minimum scene illumination *Note2
Pixel Blemish Correction
Operational temperatureStorage temperature
Angle
Standard compliancy
STC-SC83USB
SB133USB
SC133USB / STC
*Note1: As for the 10,12bit output, clock speed should be slow to obtain the correct frame rate.C1614-M with
1/3" interline 1.3M color progressive CCD:
Effective picture elements
Auto / Manual / One shot (software selectable)
SC83USB / STC-SB83USB
SC133USB / STC-SB133USB
*Note1: As for the 10,12bit output, clock speed should be slow to obtain the correct frame rate.M with C-Adaptor
STC-SC133USB1/3" interline 1.3M color progressive CCD:
ICX445AQ (Sony)
Full scanning,1/1 partial scanning,1/2 partial scanning,1/4 partial scanning,
Variable partial scanning
8.09lx at F1.2
/ Manual / One shot (software selectable)Free-run / Edge preset trigger / Pulse width trigger / Start & stop trigger (software selectable)
Auto /
1/100,000 to 1/22.40 seconds
22.40 fps44.81 fps (Normal) / 22.40 fps (1/2 clock) / 11.20 fps (1/4 clock)
36.818 MHz (Normal) / 18.409 MHz (1/2 clock) / 9.20453 MHz (1/4 clock)89.80 fps (Normal) / 44.90 fps (1/2 clock) / 22.45 fps (1/4 clock)
CS mount / MicroLens Mount (M12 P0.5) / None MountBoard Type::36(W) x 36(H) x 15.3(D) CS-Mount(without USB connector)
Accelaration 70G, half amplitude 6ms, 3 directions 3 times each20Hz to 200Hz to 20Hz (5min./cycle), acccelaration 10G, 3 directions 30 min. each
SB83USB / STC
SB133USB
*Note1: As for the 10,12bit output, clock speed should be slow to obtain the correct frame rate.Adaptor
STC-SC133USB1/3" interline 1.3M color progressive CCD:
ICX445AQ (Sony)
Full scanning,1/1 partial scanning,1/2 partial scanning,1/4 partial scanning,
Variable partial scanning
8.09lx at F1.2
/ Manual / One shot (software selectable)Free-run / Edge preset trigger / Pulse width trigger / Start & stop trigger (software selectable)
1348 (H) x 976 (V)
3.75 (H) x 3.75 (V)
Manual (software selectable,Auto / Manual (software selectable,
Approximatlly 16g
Less then 1.5W
(Hardware trigger and Software tigger are available)
+5 V through USB connector (+4.4 to +5.25V)
Green(Flicker):Power-On, Green:Camera works
USB2.0 High speed
1/100,000 to 1/22.40 seconds
1296 (H) x 966 (V)
1/100,000 to 1/11.20 seconds
6.26 (H) x 5.01 (V) mm
Progressive
22.40 fps (Normal) / 11.20 fps (1/2 clock) / 5.60 fps (1/4 clock)44.81 fps (Normal) / 22.40 fps (1/2 clock) / 11.20 fps (1/4 clock)
36.818 MHz (Normal) / 18.409 MHz (1/2 clock) / 9.20453 MHz (1/4 clock)8bit / 10bit / 12bit *Note1
1280 (H) x 960 (V) (Full scanning)1280 (H) x 440 (V) (1/2 partial scanning)1280 (H) x 168 (V) (1/4 partial scanning)
89.80 fps (Normal) / 44.90 fps (1/2 clock) / 22.45 fps (1/4 clock)
1/100,000 to 1/5.60 seconds
CS mount / MicroLens Mount (M12 P0.5) / None MountBoard Type::36(W) x 36(H) x 15.3(D) CS-Mount(without USB connector)
Auto / Manual
Accelaration 70G, half amplitude 6ms, 3 directions 3 times each
USB: mini-B USB connector
64 Points
Support on Pin 5
RoHS compliance
-30 to 65 deg. C20Hz to 200Hz to 20Hz (5min./cycle), acccelaration 10G, 3 directions 30 min. each
0 to 40 deg. CIO Connector :SM05B-SRSS-TB (JST) 5pin
Case Type: EMS: EN61000-6-2, EMI: EN55011
STC-SC133USB
*Note1: As for the 10,12bit output, clock speed should be slow to obtain the correct frame rate.
1/3" interline 1.3M monochrome progressive CCD:
Binning 1/1 partial scanning,Binning 1/2 partial scanning,Binning 1/4 partial scanning,
Binning variable partial scanning
Free-run / Edge preset trigger / Pulse width trigger / Start & stop trigger (software selectable)
1348 (H) x 976 (V)
3.75 (H) x 3.75 (V) μm
(software selectable,default: 1 (software selectable,default: x3.55
Internal
Approximatlly 16g
Less then 1.5W
(Hardware trigger and Software tigger are available)
+5 V through USB connector (+4.4 to +5.25V)
Green(Flicker):Power-On, Green:Camera works
USB2.0 High speed
1/100,000 to 1/22.40 seconds (default:1/22.40 seconds)
1296 (H) x 966 (V)
1/100,000 to 1/11.20 seconds
6.26 (H) x 5.01 (V) mm
Progressive
(Normal) / 11.20 fps (1/2 clock) / 5.60 fps (1/4 clock)44.81 fps (Normal) / 22.40 fps (1/2 clock) / 11.20 fps (1/4 clock)
36.818 MHz (Normal) / 18.409 MHz (1/2 clock) / 9.20453 MHz (1/4 clock)/ 10bit / 12bit *Note1
1280 (H) x 960 (V) (Full scanning)1280 (H) x 440 (V) (1/2 partial scanning)1280 (H) x 168 (V) (1/4 partial scanning)
89.80 fps (Normal) / 44.90 fps (1/2 clock) / 22.45 fps (1/4 clock)
1/100,000 to 1/5.60 seconds
CS mount / MicroLens Mount (M12 P0.5) / None MountBoard Type::36(W) x 36(H) x 15.3(D) CS-Mount(without USB connector)
Manual (software selectable)
Accelaration 70G, half amplitude 6ms, 3 directions 3 times each
USB: mini-B USB connector
64 Points
Support on Pin 5
RoHS compliance
-30 to 65 deg. C20Hz to 200Hz to 20Hz (5min./cycle), acccelaration 10G, 3 directions 30 min. each
0 to 40 deg. CSM05B-SRSS-TB (JST) 5pin
Case Type: EMS: EN61000-6-2, EMI: EN55011
USB / STC-SB133USB
Bold: Initial Value
*Note1: As for the 10,12bit output, clock speed should be slow to obtain the correct frame rate.
STC-SB133USB1/3" interline 1.3M monochrome progressive CCD:
ICX445AL (Sony)
Full scanning,1/1 partial scanning,1/2 partial scanning,1/4 partial scanning,
Variable partial scanning,Binning scanning,
Binning 1/1 partial scanning,Binning 1/2 partial scanning,Binning 1/4 partial scanning,
Binning variable partial scanning
0.09lx at F1.2
-Free-run / Edge preset trigger / Pulse width trigger / Start & stop trigger (software selectable)
default: 1)default: x3.55)
(Hardware trigger and Software tigger are available)
+5 V through USB connector (+4.4 to +5.25V)
Green(Flicker):Power-On, Green:Camera works
(default:1/22.40 seconds)
(Normal) / 11.20 fps (1/2 clock) / 5.60 fps (1/4 clock)44.81 fps (Normal) / 22.40 fps (1/2 clock) / 11.20 fps (1/4 clock)
36.818 MHz (Normal) / 18.409 MHz (1/2 clock) / 9.20453 MHz (1/4 clock)
1280 (H) x 440 (V) (1/2 partial scanning)1280 (H) x 168 (V) (1/4 partial scanning)
89.80 fps (Normal) / 44.90 fps (1/2 clock) / 22.45 fps (1/4 clock)
CS mount / MicroLens Mount (M12 P0.5) / None MountBoard Type::36(W) x 36(H) x 15.3(D) CS-Mount(without USB connector)
(software selectable)
Accelaration 70G, half amplitude 6ms, 3 directions 3 times each20Hz to 200Hz to 20Hz (5min./cycle), acccelaration 10G, 3 directions 30 min. each
SM05B-SRSS-TB (JST) 5pin
Case Type: EMS: EN61000-6-2, EMI: EN55011
No.13S007
SB133USB
Bold: Initial Value
STC-SB133USB1/3" interline 1.3M monochrome progressive CCD:
ICX445AL (Sony)
1/1 partial scanning,1/2 partial scanning,1/4 partial scanning,
Variable partial scanning,Binning scanning,
Binning 1/1 partial scanning,Binning 1/2 partial scanning,Binning 1/4 partial scanning,
Binning variable partial scanning
Free-run / Edge preset trigger / Pulse width trigger / Start & stop trigger (software selectable)
20Hz to 200Hz to 20Hz (5min./cycle), acccelaration 10G, 3 directions 30 min. each
No.13S007-07
10
Bold: Initial Value
STCSpecifications
Spectral Sensitivity Characteristics
STC-SC33USBSpecifications
Spectral Sensitivity Characteristics
STC
STC
1
0.8
0.4
0.6
0.2
0
Rel
ativ
e R
espo
nse
SC33USB / STC-SB33USB
Spectral Sensitivity Characteristics
STC-SC133USB
Figure 6.Spectral Sensitivity Characteristics on STC
STC-SB133USB
Figure
1
0.8
0.4
0.6
0.2
0400
1
0.8
0.4
0.6
0.2
0400
Rel
ativ
e R
espo
nse
SB33USB / STC
Spectral Sensitivity Characteristics
SC133USB (with IR cut filter)
.Spectral Sensitivity Characteristics on STC
SB133USB
Figure 7.Spectral Sensitivity Characteristics on STC
500
400
B
STC-SC83USB
Spectral Sensitivity Characteristics
(with IR cut filter)
.Spectral Sensitivity Characteristics on STC
.Spectral Sensitivity Characteristics on STC
600
500
B
SC83USB / STC-SB83USB
.Spectral Sensitivity Characteristics on STC
.Spectral Sensitivity Characteristics on STC
700Wave length [nm]
Wave length [nm]
G
SB83USB / STC
.Spectral Sensitivity Characteristics on STC-SC13
.Spectral Sensitivity Characteristics on STC
800Wave length [nm]
600Wave length [nm]
IR cut filter
STC-SC133USB
133USB (with IR cut filter)
.Spectral Sensitivity Characteristics on STC-SB133USB
800
R
IR cut filter
USB / STC-SB133USB
3USB (with IR cut filter)
SB133USB
900
700
No.13S007
SB133USB
3USB (with IR cut filter)
1000
No.13S007-07
11
STCSpecifications
3 Interface Connector S
STC-SC33USBSpecifications
nterface Connector S
A) USB connector:B) I/O connector:
Pin assignment
Table 4.Pin assignment on STC
Figure 9.Connector on the rear
Input and output signals are isolated.Reset
C) LED
1 IO_GND
2 IO_VCC
3 IO_OUT45
Pin
A)
SC33USB / STC-SB33USB
nterface Connector S
USB connector:I/O connector:
Pin assignment
.Pin assignment on STC
Connector on the rear
Input and output signals are isolated.Reset Port: Pin N is assigned as Rest. When camera does not recognize on PC. Once Reset signal is
inputtedLED
IO_GND IO GND
IO_VCC IO Power
IO_OUT Camera OutputIO_IN Camera InputRST Camera Reset
Singal Function
) USB connector
SB33USB / STC
nterface Connector Specifications
Figure
USB connector: Mini-B USB typeI/O connector: Angle:
StraightCable Side: This connector is for the Trigger input and the output signals can be assigned through the camera setting communication.The power in the connector is for the input / output signals, NOT for the camera power.
.Pin assignment on STC
Connector on the rear panel
Input and output signals are isolated.Port: Pin N is assigned as Rest. When camera does not recognize on PC. Once Reset signal is
inputted, camera will reboot without plugGreen (Flicker ):Green:
IO GND
IO Power
Camera OutputCamera InputCamera Reset
Function
connector
C) LED
STC-SC83USB
pecifications(Board Type
Figure 8.Back view on STC
B USB type :SM05B-SRSS
Straight(Option):Cable Side: SHR-05VThis connector is for the Trigger input and the output signals can be assigned through the camera setting communication. The power in the connector is for the input / output signals, NOT for the camera power.
.Pin assignment on STC-SC/SB**USB Series
panel
Input and output signals are isolated. Port: Pin N is assigned as Rest. When camera does not recognize on PC. Once Reset signal is
, camera will reboot without plugGreen (Flicker ): PowerGreen: Camera works
- IO GND
IN
+2.0 to 5.0Vdc
OUTININ
IOElectric
Specification
C) LED
SC83USB / STC-SB83USB
Board Type)
.Back view on STC-SC/SB**USB Series
SRSS-TB (JST) 5pin or equivalent :BM05B-SRSS
05V-S-B or equivalentThis connector is for the input and output signals.Trigger input and the output signals can be assigned through the camera setting
The power in the connector is for the input / output signals, NOT for the camera power.
SC/SB**USB Series
Port: Pin N is assigned as Rest. When camera does not recognize on PC. Once Reset signal is
, camera will reboot without plugPower-ON
Camera works
IO GND
+2.0 to 5.0Vdc
No-Function
No-Function
Enable
ElectricSpecification
Default
SB83USB / STC
SC/SB**USB Series
TB (JST) 5pin or equivalent SRSS-TB (JST) 5pin or equivalentor equivalent
input and output signals.Trigger input and the output signals can be assigned through the camera setting
The power in the connector is for the input / output signals, NOT for the camera power.
Port: Pin N is assigned as Rest. When camera does not recognize on PC. Once Reset signal is , camera will reboot without plug-out the USB cable.
-
-
No-Function
No-Function
Enable
Default
STC-SC133USB
SC/SB**USB Series
TB (JST) 5pin or equivalent TB (JST) 5pin or equivalent
input and output signals. Trigger input and the output signals can be assigned through the camera setting
The power in the connector is for the input / output signals, NOT for the camera power.
Port: Pin N is assigned as Rest. When camera does not recognize on PC. Once Reset signal is out the USB cable.
B) I/O connector
USB / STC-SB133USB
TB (JST) 5pin or equivalent
Trigger input and the output signals can be assigned through the camera setting
The power in the connector is for the input / output signals, NOT for the camera power.
Port: Pin N is assigned as Rest. When camera does not recognize on PC. Once Reset signal is out the USB cable.
[Side View]
1 5
I/O connector
No.13S007
SB133USB
Trigger input and the output signals can be assigned through the camera setting
The power in the connector is for the input / output signals, NOT for the camera power.
Port: Pin N is assigned as Rest. When camera does not recognize on PC. Once Reset signal is
[Side View]
1 5
↓Board
I/O connector
No.13S007-07
12
Trigger input and the output signals can be assigned through the camera setting
The power in the connector is for the input / output signals, NOT for the camera power.
Port: Pin N is assigned as Rest. When camera does not recognize on PC. Once Reset signal is
Board
STCSpecifications
4 Input / Output signals specifications 4.1 Input signals specifications
STC-SC33USBSpecifications
Input / Output signals specifications
Input signals specifications 4.1.1 Function for the input signals
The following functions can be configured for the input signals (IN1) through the software.
The polarity for the trigger signal input can be selectable.
4.1.2 Characteristics of the input signals
Input signal level:
Hardware
4.1.3 Input signal circuit
4.1.4 Reset signalThe camera will be reset after 5 seconds high signal on Pin 5.
SC33USB / STC-SB33USB
Input / Output signals specifications
Input signals specifications
Function for the input signalsThe following functions can be configured for the input signals (IN1) through the software.
Table 5.Function table on Input
The polarity for the trigger signal input can be selectable.
Characteristics of the input signals
Input signal level:
Hardware trigger pulse width: more than 0.1 usec
Input signal circuit
Reset signal The camera will be reset after 5 seconds high signal on Pin 5.
No.1 No signal (Default)2 General input3 Trigger signal input
SB33USB / STC
Input / Output signals specifications
Input signals specifications
Function for the input signalsThe following functions can be configured for the input signals (IN1) through the software.
.Function table on Input
The polarity for the trigger signal input can be selectable.
Characteristics of the input signals
Input signal level: High: IO VCC IN (+Low: Smaller than 0.8
rigger pulse width: more than 0.1 usec
Input signal circuit (Include reset signal)
The camera will be reset after 5 seconds high signal on Pin 5.
FunctionsNo signal (Default)General inputTrigger signal input
STC-SC83USB
Input / Output signals specifications
Function for the input signals The following functions can be configured for the input signals (IN1) through the software.
.Function table on Input
The polarity for the trigger signal input can be selectable.
Characteristics of the input signals
High: IO VCC IN (+Low: Smaller than 0.8
rigger pulse width: more than 0.1 usec
(Include reset signal)
Figure 10
The camera will be reset after 5 seconds high signal on Pin 5.
Polarity
Trigger signal input Positive / Negative
SC83USB / STC-SB83USB
The following functions can be configured for the input signals (IN1) through the software.
The polarity for the trigger signal input can be selectable.
High: IO VCC IN (+2.0 to +5.0V)Low: Smaller than 0.8V
rigger pulse width: more than 0.1 usec
(Include reset signal)
10.Input circuit diagram
The camera will be reset after 5 seconds high signal on Pin 5.
Polarity--
Positive / Negative
SB83USB / STC
The following functions can be configured for the input signals (IN1) through the software.
The polarity for the trigger signal input can be selectable.
V)
.Input circuit diagram
The camera will be reset after 5 seconds high signal on Pin 5.
STC-SC133USB
The following functions can be configured for the input signals (IN1) through the software.
USB / STC-SB133USB
The following functions can be configured for the input signals (IN1) through the software.
No.13S007
SB133USB
The following functions can be configured for the input signals (IN1) through the software.
No.13S007-07
13
STCSpecifications
4.2 Output signals
STC-SC33USBSpecifications
Output signals 4.2.1 Function for the output signals
The following functions can be configured for the output signals (OUT) through the software
Table
The polarity for the trigger signal, the exposure end signal, the CCD read out end signal, the strobe signal (time setting) and the strobe signal (exposure time) can be selectable.
4.2.2 Characteristics of the output signal
Output signal level: Output signal duration: The signal duration should be longer than “Tf + Tr”.
Output signal response timings:
No.1234567
SC33USB / STC-SB33USB
Output signals specifications
Function for the output signalsThe following functions can be configured for the output signals (OUT) through the software
Table 6..Function table on Output
The polarity for the trigger signal, the exposure end signal, the CCD read out end signal, the strobe signal (time setting) and the strobe signal (exposure time) can be selectable.
Characteristics of the output signal
Output signal level:
Output signal duration: The signal duration should be longer than “Tf + Tr”.
Output signal response timings:
Table
No.No signal (Default)General outputTrigger signal outputExposure end signal outputCCD read out end signal outputStrobe signal output (Time setting)Strobe signal output (Exposure time)
Camera inside
USER OUTPUT
SB33USB / STC
specifications
Function for the output signalsThe following functions can be configured for the output signals (OUT) through the software
Function table on Output
The polarity for the trigger signal, the exposure end signal, the CCD read out end signal, the strobe signal (time setting) and the strobe signal (exposure time) can be selectable.
Characteristics of the output signal
Output signal level: High: IO VCC IN (+3Low: Smaller than 0.8V
Output signal duration: The signal duration should be longer than “Tf + Tr”.Please check “Output signal response timings” for Tf and Tr.The signal duration can adjust by
Output signal response timings:
Table 7.Output
FunctionsNo signal (Default)General outputTrigger signal outputExposure end signal outputCCD read out end signal outputStrobe signal output (Time setting)Strobe signal output (Exposure time)
Camera inside
USER OUTPUT
Tf
Ts
Tr
Td
STC-SC83USB
Function for the output signals The following functions can be configured for the output signals (OUT) through the software
Function table on Output
The polarity for the trigger signal, the exposure end signal, the CCD read out end signal, the strobe signal (time setting) and the strobe signal (exposure time) can be selectable.
Characteristics of the output signals
High: IO VCC IN (+3Low: Smaller than 0.8V
Output signal duration: The signal duration should be longer than “Tf + Tr”.Please check “Output signal response timings” for Tf and Tr.The signal duration can adjust by
Output signal response timings:
Figure 11
.Output response time
Functions
Exposure end signal outputCCD read out end signal outputStrobe signal output (Time setting)Strobe signal output (Exposure time)
Ts
0.06[us]
0.07 [us]
1.86 [us]
2.80 [us]
3.3[V]
SC83USB / STC-SB83USB
The following functions can be configured for the output signals (OUT) through the software
The polarity for the trigger signal, the exposure end signal, the CCD read out end signal, the strobe signal (time setting) and the strobe signal (exposure time) can be selectable.
High: IO VCC IN (+3.0 to +26.4V)Low: Smaller than 0.8V
Output signal duration: The signal duration should be longer than “Tf + Tr”.Please check “Output signal response timings” for Tf and Tr.The signal duration can adjust by
11.Output response time
response time
Polarity--
Positive / NegativePositive / NegativePositive / NegativePositive / Negative
Strobe signal output (Exposure time) Positive / Negative
Tf
0.07
[us]
0.07
[us]
1.95
[us]
2.76
[us]
5.0[V]
IO_VCC
SB83USB / STC
The following functions can be configured for the output signals (OUT) through the software
The polarity for the trigger signal, the exposure end signal, the CCD read out end signal, the strobe signal (time setting) and the strobe signal (exposure time) can be selectable.
to +26.4V)
Output signal duration: The signal duration should be longer than “Tf + Tr”.Please check “Output signal response timings” for Tf and Tr.The signal duration can adjust by the software.
.Output response time
Polarity
Positive / NegativePositive / NegativePositive / NegativePositive / NegativePositive / Negative
Td
Tr
0.12 [us]
0.08 [us]
1.74 [us]
2.72 [us]
12[V]
IO_VCC
STC-SC133USB
The following functions can be configured for the output signals (OUT) through the software
The polarity for the trigger signal, the exposure end signal, the CCD read out end signal, the strobe signal (time setting) and the strobe signal (exposure time) can be selectable.
Output signal duration: The signal duration should be longer than “Tf + Tr”. Please check “Output signal response timings” for Tf and Tr.
the software.
10%
90%
0.18
[us]
0.08[us]
1.95
[us]
2.54
[us]
24[V]
USB / STC-SB133USB
The following functions can be configured for the output signals (OUT) through the software
The polarity for the trigger signal, the exposure end signal, the CCD read out end signal, the strobe signal
Please check “Output signal response timings” for Tf and Tr.
3.3V
0V
IO_VCC
IO_GND
No.13S007
SB133USB
The following functions can be configured for the output signals (OUT) through the software on Pin 3.
The polarity for the trigger signal, the exposure end signal, the CCD read out end signal, the strobe signal
No.13S007-07
14
The polarity for the trigger signal, the exposure end signal, the CCD read out end signal, the strobe signal
STCSpecifications
STC-SC33USBSpecifications
4.2.3 Output signal circuit
SC33USB / STC-SB33USB
Output signal circuit
SB33USB / STC
Output signal circuit
STC-SC83USB
Figure 12.Output circuit diagram
SC83USB / STC-SB83USB
.Output circuit diagram
SB83USB / STC
.Output circuit diagram
STC-SC133USB
.Output circuit diagram
Camera IO PortCamera
USB / STC-SB133USB
Camera IO Port
No.13S007
SB133USB
Camera IO Port
No.13S007-07
15
STCSpecifications
5 Dimensions
5.1 STC
STC-SC33USBSpecifications
Dimensions STC-SCxxxUSB
SC33USB / STC-SB33USB
Dimensions
SCxxxUSB-BxCS (Color, Board
SB33USB / STC
CS (Color, Board
Figure 13.Mechanical dimensions
STC-SC83USB
CS (Color, Board type, CS-
USB
USB Straight connector
.Mechanical dimensions
SC83USB / STC-SB83USB
-Mount, USB Angle
USB Angle connector
USB Straight connector
.Mechanical dimensions
SB83USB / STC
, USB Angle / Straight
connector
USB Straight connector
.Mechanical dimensions (STC-SCxxxUSB
STC-SC133USB
Straight)
SCxxxUSB-BxCS)
USB / STC-SB133USB
CS)
No.13S007
SB133USB
Unit: mm
No.13S007-07
16
STCSpecifications
5.2 STC
*Note:
5.3 STC*Note:
STC-SC33USBSpecifications
STC-SBxxxUSB*Note: As for the USB Straight
STC-SCxxxUSB*Note: As for the USB Straight
SC33USB / STC-SB33USB
SBxxxUSB-BLCS (MonoUSB Straight
SCxxxUSB-BL / STCUSB Straight
Figure15
SB33USB / STC
CS (Monochrome, Board USB Straight connector dimensions, please refer to the
Figure 14. Mechanical dimensions
/ STC-SBxxxUSBUSB Straight connector dimensions, please refer to the.
15.Mechanical dimensions
STC-SC83USB
hrome, Board type, CSdimensions, please refer to the
USB
. Mechanical dimensions
SBxxxUSB-BL (Colorconnector dimensions, please refer to the.
USB
.Mechanical dimensions
SC83USB / STC-SB83USB
ype, CS-Mountdimensions, please refer to the
USB Angle connector
. Mechanical dimensions
(Color / Monochrome,connector dimensions, please refer to the.
USB Angle connector
.Mechanical dimensions (STC-SCxxxUSB
SB83USB / STC
Mount, USB Angledimensions, please refer to the Fig13.
ngle connector
. Mechanical dimensions (STC-SBxxxUSB
hrome, Board connector dimensions, please refer to the.Fig13.
ngle connector
SCxxxUSB-BL
STC-SC133USB
USB Angle / Straight.
SBxxxUSB-BLCS)
Board type, No-MountFig13.
L / STC-SBxxxUSB
USB / STC-SB133USB
Straight* )
CS)
Mount, USB Angle
SBxxxUSB-BL)
Unit:
No.13S007
SB133USB
USB Angle / Straight*
Unit: mm
No.13S007-07
17
Straight*)
STCSpecifications
5.4 STC*Note:
5.5 STC*Note:
STC-SC33USBSpecifications
STC-SCxxxUSB*Note: As for the USB Straight
STC-SBxxxUSB*Note: As for the USB Straight
SC33USB / STC-SB33USB
SCxxxUSB-BLL (Color,USB Straight
SBxxxUSB-BLL (MonoUSB Straight
SB33USB / STC
(Color, Board USB Straight connector dimensions, please refer to the
Figure 16.Mecha
L (Monochrome, Board USB Straight connector dimensions, please refer to the
Figure 17.Mechanical dimensions
STC-SC83USB
Board type, Fixed Focusconnector dimensions, please refer to the
USB
.Mechanical dimensions
hrome, Board type, Fixed Focusconnector dimensions, please refer to the
USB
.Mechanical dimensions
SC83USB / STC-SB83USB
ype, Fixed Focus, USB Angleconnector dimensions, please refer to the
USB Angle connector
nical dimensions
ype, Fixed Focusconnector dimensions, please refer to the
USB Angle connector
.Mechanical dimensions
SB83USB / STC
, USB Angle / Straight*connector dimensions, please refer to the Fig13.
ngle connector
nical dimensions (STC-SCxxxUSB
ype, Fixed Focus, USB Angleconnector dimensions, please refer to the Fig13.
ngle connector
.Mechanical dimensions (STC-SBxxxUSB
STC-SC133USB
Straight*) Fig13. .
SCxxxUSB-BLL
, USB Angle / StraightFig13.
SBxxxUSB-BLL
USB / STC-SB133USB
L)
Straight*)
L)
Unit:
Unit:
No.13S007
SB133USB
Unit: mm
Unit: mm
No.13S007-07
18
STCSpecifications
5.6 STC*Note:
STC-SC33USBSpecifications
STC-SCxxxUSB*Note: As for the USB Straight
SC33USB / STC-SB33USB
SCxxxUSB-AL / STCUSB Straight
Figure 18
SB33USB / STC
STC-SBxxxUSBUSB Straight connector dimensions, please refer to the
18.Mechanical
STC-SC83USB
SBxxxUSB-AL (Colorconnector dimensions, please refer to the
.Mechanical dimensions
SC83USB / STC-SB83USB
AL (Color / Monochrome,connector dimensions, please refer to the
dimensions (STC-SCxxxUSB
SB83USB / STC
hrome, Cased connector dimensions, please refer to the Fig13.
SCxxxUSB-AL / STC
STC-SC133USB
Cased type, CS-Fig13.
L / STC-SBxxxUSB
USB / STC-SB133USB
-Mount* )
SBxxxUSB-AL)
Unit:
No.13S007
SB133USB
Unit: mm
No.13S007-07
19
STCSpecifications
6 Revisions
Rev1.001.011.021.031.04
1.05
1.061.07
STC-SC33USBSpecifications
Revisions Rev Date1.00 2013/08/231.01 2013/09/131.02 2013/11/251.03 2013/11/291.04 2014/01/17
2014/02/19
1.05 2014/03/122014/12/18
1.06 2015/03/171.07 2015/11/20
SC33USB / STC-SB33USB
Date
23 New document2013/09/13 Revised: 2013/11/25 Revised:2013/11/29 Revised: Added USB 2014/01/17
2014/02/19
Revised: Added cased type model Added explanation around IO portRevised
2014/03/12 2014/12/18
Revised: Replaced the drawing of Added
2015/03/17 Revised: Maxi2015/11/20 Revised:
SB33USB / STC
New documentRevised: Minimum scene illuminationRevised: IO port description Revised: Added USB Revised: Added cased type modelAdded explanation around IO port
Revised -ALCS Revised: Replaced the drawing ofAdded Information
Revised: MaxiRevised: Change the name of c
STC-SC83USB
New document Minimum scene illuminationIO port description
Revised: Added USB straight connector information
Added cased type model,Added explanation around IO port
ALCS ->--AL on cased type Revised: Replaced the drawing of
Information of IO connectorRevised: Maximum shutter speed to
Change the name of c
SC83USB / STC-SB83USB
Changes
Minimum scene illumination IO port description
straight connector information
, Added explanation around IO port(IO table and Trigger
AL on cased type Revised: Replaced the drawing of -BxL model
of IO connector shutter speed to 1/100,000
Change the name of company
SB83USB / STC
Changes
straight connector information
(IO table and Trigger
BxL model
1/100,000 secompany
STC-SC133USB
straight connector information
(IO table and Trigger Pulse)
sec
USB / STC-SB133USB
)
No.13S007
SB133USB
Note
No.13S007-07
20
Note
STCSpecifications
STC-SC33USBSpecifications
SC33USB / STC-SB33USB
SB33USB / STCSTC-SC83USB SC83USB / STC-SB83USBSB83USB / STC
9F, Ebina Prime Tower9-50, Chuo 2 chomeEbina-city, Kanagawa243-0432 JapanTEL 81-46-URL http://www.sentech.co.jp/
STC-SC133USB
9F, Ebina Prime Tower 50, Chuo 2 chome
city, Kanagawa 0432 Japan
-236-6660 FAX 81URL http://www.sentech.co.jp/
USB / STC-SB133USB
6660 FAX 81-46-236URL http://www.sentech.co.jp/
No.13S007
SB133USB
236-6661
No.13S007-07
21