sitrans - cache.industry.siemens.com · a5e32043113 sitrans lr560 (profibus pa) page en-1 mmmmm...

Radar Transmitters

Quick Start Manual 03/2013

SITRANS LR560 (PROFIBUS PA)

SITRANS

A5E32043113 SITRANS LR560 (PROFIBUS PA) Page EN-1

mm

mm

m

English

SITRANS LR560 (PROFIBUS PA) Quick Start Manual This manual outlines the essential features and functions of the SITRANS LR560 (PROFIBUS PA). We strongly advise you to acquire the detailed version of the manual so you can use your device to its fullest potential. The complete manual can be downloaded from the SITRANS LR560 product page of our web site at: www.siemens.com/LR560. The printed manual is available from your local Siemens Milltronics representative.

Questions about the contents of this manual can be directed to:Siemens AGSiemens Milltronics Process Instruments1954 Technology Drive, P.O. Box 4225Peterborough, Ontario, Canada, K9J 7B1Email: [email protected]

MILLTRONICS is a registered trademark of Siemens Milltronics Process Instruments.

Technical SupportSupport is available 24 hours a day.

To find your local Siemens Automation Office address, phone number, and fax number, go to:

www.siemens.com/automation/partner: Click on the tab Contact, select Service, then click Service again to find your

product group (+Automation Technology > +Sensor Systems >+Process Instrumentation > +Level Measurement > +Continuous). Select Radar.

Select the country followed by the City/Region. Select Technical Support under Service.

For on-line technical support go to: www.siemens.com/automation/support-request Enter the device name (SITRANS LR560) or order number, then click on Search, and

select the appropriate product type. Click on Next. Enter a keyword describing your issue. Then either browse the relevant documentation,

or click on Next to email a description of your issue to Siemens Technical Support staff.

Siemens IA/DT Technical Support Center: phone +49 (0)911 895 7222

Copyright Siemens AG 2013. All Rights Reserved Disclaimer of Liability

We encourage users to purchase autho-rized bound manuals, or to view elec-tronic versions as designed and authored by Siemens Milltronics Process Instruments. Siemens Milltronics Pro-cess Instruments will not be responsible for the contents of partial or whole reproductions of either bound or elec-tronic versions.

While we have verified the contents of this manual for agreement with the instrumentation described, variations remain possible. Thus we cannot guar-antee full agreement. The contents of this manual are regularly reviewed and corrections are included in subsequent editions. We welcome all suggestions for improvement.

Technical data subject to change.

Page EN-2 SITRANS LR560 (PROFIBUS PA) A5E32043113

mm

mm

m

Engl

ish

Safety GuidelinesWarning notices must be observed to ensure personal safety as well as that of others, and to protect the product and the connected equipment. These warning notices are accompanied by a clarification of the level of caution to be observed.

FCC ConformityUS Installations only: Federal Communications Commission (FCC) rules

Industry Canadaa) Operation is subject to the following two conditions: (1) this device may not cause

interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

b) This device shall be installed and operated in a completely enclosed container to prevent RF emission which otherwise can interfere with aeronautical navigation. Installation shall be done by trained installers, in strict compliance with the manufacturers instructions.

c) The use of this device is on a no-interference, no-protection basis. That is, the user shall accept operations of high-powered radar in the same frequency band which may interfere with or damage this device. On the other hand, level probing devices found to interfere with primary licensing operations will be required to be removed at the users expense.

WARNING symbol relates to a caution symbol on the product, and means that failure to observe the necessary precautions can result in death, serious injury, and/or considerable material damage.WARNING symbol, used when there is no corresponding caution symbol on the product, means that failure to observe the necessary precautions can result in death, serious injury, and/or considerable material damage.

Note: means important information about the product or that part of the operating manual.

WARNING: Changes or modifications not expressly approved by Siemens Milltronics could void the users authority to operate the equipment.

Notes: This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reason-able protection against harmful interference when the equipment is operated in a com-mercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful inter-ference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference to radio communications, in which case the user will be required to correct the interference at his own expense.


mm

mm

m

Englishd) This level probing device is only permitted for installation inside enclosed containers. The

installer/user of this device shall ensure that it is at least 10 km from the Penticton radio astronomy station (British Columbia latitude: 49 19' 12" N, longitude: 119 37'12" W). For devices not meeting this 10 km separation (e.g. the Okanagan Valley, British Columbia) the installer/ user must coordinate with and obtain the written concurrence of the Director of the Penticton radio astronomy station before the equipment can be installed or operated. The Penticton contact is Tel: 250-493-2277/ fax: 250-493-7767. (In case of difficulty, the Manager, Radio Equipment Standards, Industry Canada, may also be contacted.)

R&TTE Compliance (Europe)Hereby, Siemens Milltronics Process Instruments, declares that the SITRANS LR560 is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.

The LR560 complies with EN 302 372 for use in closed storage vessels, when installed according to the installation requirements of EN 302 372, and may be used in all EU countries.

The LR560 complies with Draft ETSI EN 302 729 for use outside of closed tanks in most EU countries. (For a list of exceptions, see the LR560 Declaration to EN 302 729, which can be accessed online at www.siemens.com/LR560.) For open air installations, the following conditions must be observed:

Installation and maintenance is performed by suitably qualified and trained personnel.The LR560 shall be installed only in a permanent fixed position pointing downwards. Its location shall comply with the following two restrictions:

1) It shall be installed with a minimum separation distance of 4 km from Radio Astronomy sites listed below unless special authorization has been provided by the responsible national regulatory authority.

2) If it is installed at a location between 4 and 40 km from any Radio Astronomy site listed below, the LR560 shall be installed at a height not exceeding 15m from the ground.

The LR560 Declaration of Conformity may be accessed online at www.siemens.com/LR560.

Country Name of Station Geographic Latitude Geographic Longitude

FrancePlateau de Bure 443801 N 055426 E

Bordeaux 448400 N 05200 W

Germany Effelsberg 503132 N 065300 E

Italy Sardinia 392950 N 091440 E

SpainYebes 403127 N 030522 W

Pico Veleta 370358.3 N 032333.7 W

Sweden Onsala 572345 N 115535 E

http:/http:/http:/


mm

mm

m

Engl

ish

SITRANS LR560

SITRANS LR560 is a 2-wire 78 GHz FMCW radar level transmitter for continuous monitoring of solids in vessels to a range of 100 m (329 ft). The plug and play performance is ideal for all solids applications, including those with extreme dust and high temperatures to +200 C (+392 F).

The device consists of an electronic circuit coupled to a lens antenna and flange for quick and easy positioning.

SITRANS LR560 supports PROFIBUS PA communication protocol, and SIMATIC PDM software. Signals are processed using Process Intelligence.

SpecificationsFor a complete listing, see the SITRANS LR560 (PROFIBUS PA) Instruction Manual. For Approvals information see Approvals on page 5.

Ambient/Operating Temperature

Power Bus powered 9 to 32 V DC, per IEC 61158-2 (PROFIBUS PA) Current consumed 13.5 mA

WARNING: SITRANS LR560 is to be used only in the manner outlined in this manual, otherwise protection provided by the equipment may be impaired.

Note: This product is intended for use in industrial areas. Operation of this equipment in a residential area may cause interference to several frequency based communications.

Notes: The reference drawing listed on the device label can be downloaded from the Siemens

website at: www.siemens.com/LR560 under Support. Maximum and minimum temperatures are dependent on the process connection, antenna

and O-ring materials. Use of the Easy Aimer limits maximum temperature. See Temperature De-Rating Curve on page 15, for more details.

process temperature at process connection: 40 oC to +100 oC (40 oF to +212 oF) or 40 oC to +200 oC (40 oF to +392 oF) depending on the version

ambient temperature(surrounding enclosure)

40 C to 80 C (40 F to 176 F) device label

pressure/ temperature related information


mm

mm

m

English

Approvals

General CSAUS/C, FM, CE, C-TICK Radio R&TTE (Europe), FCC, Industry Canada Hazardous

Non-sparking/Energy Limited 1) (Europe) ATEX II 3G Ex nA/nL IIC T4 Gc

(Brazil) INMETRO: DNV 12.0085 XEx nA IIC T4 Gc-40 C Ta +80 CUn = 32 VccDNV #OCP 0017ABNT NBR IEC 60079-0:2008, ABNT NBR IEC 60079-15:2012

Dust Ignition Proof 1) (Europe/International) ATEX II 1D, 1/2D, 2DIECEx SIR 09.0149XEx ta IIIC T139 oC Da

(Brazil) INMETRO: DNV 12.0085 XEx ta IIIC T139 C Da IP68-40 C Ta +80 CDNV #OCP 0017ABNT NBR IEC 60079-0:2008 eABNT NBR IEC 60079-31:2011

Dust Ignition Proof 2) (US/Canada) FM/CSAClass II, Div. 1, Groups E, F, GClass III T4

Non-incendive2) (US/Canada) FM/CSA Class I, Div. 2, Groups A, B, C, D, T4

Pressure Application

Pressure Equipment Directive, PED, 97/23/EC

SITRANS LR560 Radar Level Measurement instrument falls below the limits of Article 3, sections 1&2 of the Pressure Equipment directive (PED, 97/23/EC), as a category I pressure accessory. However, in accordance with PED, 97/23/EC, Article 3, section 3, this equipment has been designated and manufactured in accordance with Sound Engineering Practice (SEP) (see EU Commission Guideline 1/5).

Notes: The device label lists the approvals that apply to your device. Use appropriate conduit seals to maintain IP or NEMA rating.

1) See also Non-Sparking/Energy Limited wiring (Europe) and Dust Ignition Proof wiring (Europe/Inter-national) on page 16.

2) See also Non-incendive and Dust Ignition Proof wiring (US/Canada) on page 17.

WARNINGS:

Do not attempt to loosen, remove, or disassemble process connection or instru-ment housing while vessel contents are under pressure.

Improper installation may result in loss of process pressure.

Note: Pertains to pressure-rated version only.


mm

mm

m

Engl

ish

Installation

Nozzle locationBeam angle

Beam angle is the width of the cone where the energy density is half of the peak energy density.

The peak energy density is directly in front of and in line with the antenna.

There is a signal transmitted outside the beam angle, therefore false targets may be detected.

Emission cone Keep emission cone free of interference

from ladders, pipes, I-beams or filling streams.

Avoid central locations on tall, narrow ves-sels.

Environment

Provide easy access for viewing the dis-play and programming via the hand pro-grammer.

Provide an environment suitable to the housing rating and materials of construction.

WARNINGS: Installation shall be performed only by qualified personnel and in accor-

dance with local governing regulations. Never attempt to loosen, remove, or disassemble process connection or

instrument housing while vessel contents are under pressure. The user is responsible for the selection of bolting and gasket materials

which will fall within the limits of the flange and its intended use and which are suitable for the service conditions.

Improper installation may result in loss of process pressure.

Note: SITRANS LR560 units are pressure tested, meeting or exceeding the requirements of the ASME Boiler and Pressure Vessel Code and the European Pressure Equipment Directive.

emission cone

4


mm

mm

m

EnglishSun Shield

The LR560 display can be protected by an optional sun shield if the instrument will be mounted in direct sunlight

Aimer Adjustment

3" flange 4 and 6" flange

1) For 4" and 6" Aimer: loosen the set screws in the locking ring. Holding the electronics enclosure firmly, loosen the Aimer locking ring using the supplied C spanner, until the LR560 drops down slightly. The enclosure can then be turned freely.

2) Direct SITRANS LR560 so the antenna is pointed at an angle perpendicular to the material surface, if possible.

3) When the desired position is reached, re-tighten the locking ring using the C spanner, and tighten set screws.

4) For the 3" Aimer flange, tapered split washers with pressure rated versions are provided to keep nuts and bolts perpendicular to the flange surface.

Aimer Aiming is not required for signal optimization with 78 GHz frequency.

Aiming will assist in measuring material in the cone.


mm

mm

m

Engl

ish

Air Purge SystemThe purge airflow is designed to create a strong vortex of air that rapidly cleans the face of the lens. See the full manual for details.

WiringPower

Connecting SITRANS LR560

1) Loosen locking screw.2) Remove LR560 lid. 3) Remove optional display by gently turning the

display a quarter turn counter-clockwise until it is free.

4) Strip the cable jacket for approximately 70 mm (2.75") from the end of the cable, and thread the wires through the gland 1).

5) Connect the wires to the terminals as shown. SITRANS LR560 (PROFIBUS PA) is not polarity sensitive.

6) Ground the instrument according to local regulations.

7) Tighten the gland to form a good seal.8) Replace optional display.9) After programming and device configuration,

replace device lid and secure locking screw.

WARNINGS:The DC input terminals shall be supplied from a source providing electrical isolation between the input and output, in order to meet the applicable safety requirements of IEC 61010-1.

All field wiring must have insulation suitable for rated voltages.

WARNINGS: Check the device label to verify the approval rating. Use appropriate conduit seals to maintain IP or NEMA rating. Read Instructions Specific to Hazardous Area Installations on page 17.Note: For detailed wiring instructions refer to the full Instruction Manual.

1) If cable is routed through conduit, use only approved suitable-size hubs for waterproof applications.

1)

2)

3) turn

cable gland (or NPT cable entry)

cable shield

instrument shield connection


mm

mm

m

English

Installing PROFIBUS PA Devices PROFIBUS PA must be terminated at both extreme ends of the cable for it to work properly. Please refer to the PROFIBUS PA User and Installation Guidelines (order number 2.092),

available from www.profibus.com, for information on installing PROFIBUS devices. If a Weidmller or other current limiting junction box is connected to this device, please

ensure that the current limit is set to 40 mA or higher..

Basic PLC configuration with PROFIBUS PA

Wiring setups for hazardous area installationsSee Wiring setups for hazardous area installations on page 16

Programming SITRANS LR560 See Quick Start Wizard via the LDI push buttons on page 11. See Quick Start Wizard via SIMATIC PDM on page 14.

Activating SITRANS LR560Power up the device. A transition screen showing first the Siemens logo and then the current firmware revision is displayed while the first measurement is being processed. SITRANS LR560 automatically starts up in Measurement mode.

The first time the device is configured, you will be prompted to select a language (English, German, French, Spanish or Chinese).

Local Display Interface (LDI)Modify parameters using the LDI push buttons.

(Siemens infrared handheld programmer can be ordered separately: [Part No. 7ML1930-1BK]).

PROFIBUS PA

PROFIBUS DP

DP/PA coupler

active PLC

PC/laptop

PDM

SITRANS LR560 PA

SITRANS LR560 PA

SITRANS LR560 PA


mm

mm

m

Engl

ish

The LCD DisplayMeasurement mode display (normal operation)

1)

Fault present indicators

Program mode display

Navigation view A visible menu bar indicates the

menu list is too long to display all items.

The depth of the item band on the menu bar indicates the length of the menu list: a deeper band indicates fewer items.

The position of the item band indicates the approximate position of the current item in the list. A band halfway down the menu bar indicates the current item is halfway down the list. A deeper band indicates fewer items.

1) Press or to switch.

Note: For a complete list of parameters, refer to the full manual.

1 toggle indicator1) for AIFB 1 or AIFB 22 identifies which AIFB is source of displayed value3 measured value (level, space, or distance)4 units5 bar graph indicates level6 text area displays status messages 7 device status indicator

67

1 3 42

5

S: 0 LOEWhen a fault is present the fault code and an error message are displayed in the text area (7), and a service-required icon appears in the device status location (8)

current item number

current item

current menu

item band

menu bar

parameter value/selection

parameter numberparameter

name

Edit viewParameter view


mm

mm

m

English

PROGRAM modeUsing the LDI push buttons, press to enter Program Mode and open menu level 1. Scroll through the menu using , , , .

To edit a number

1) Navigate to the desired parameter, for example, Low Calibration point (2.3.1), and press twice to open and edit it. The value will be highlighted.

2) Press or to delete the highlighted value.3) With the Enter icon highlighted , press to add a digit.4) Use or to modify the highlighted digit. Scroll past 9 to

reach the decimal point.5) Press to select and highlight the plus or minus sign. Press or to change it. 6) Press until the Enter icon is highlighted , then press to add a digit on the right.7) When the value is complete, press until the Enter icon is highlighted , then press

to accept the value.

To modify a text string:1) Navigate to the parameter you wish to modify and press to edit it. The string will be

highlighted.2) Follow the same steps as above, to add, delete, or modify characters.

Quick Start Wizard via the LDI push buttons1. Quick Start

1.1. Quick Start Wizard

1) Press twice to navigate to Quick Start (1.) and open Quick Start Wizard (1.1.)

2) At each step, press to accept default values and move directly to the next item, or to open Edit mode: the current selection is highlighted.

3) Scroll to desired item and press to store the change, then press to continue.

4) At any time, you can press to go back, or to cancel and return to Measurement mode.

Note: With the Enter icon highlighted, press to insert a digit on the right, to delete the right-most digit, to accept the value, or to cancel.

Note: Default values are indicated by an asterisk (*) in the tables below, unless explicitly described.


mm

mm

m

Engl

ish

Vessel

Response Rate

Use a setting just faster than the maximum vessel filling or vessel emptying rate (whichever is greater). Units

Operation

Response RateVessel Fill Rate or Empty Rate

per minuteFilter Time Constant

SLOW 0.1 m/min (0.32 ft/min) 600 sMED 1.0 m/min (3.28 ft/min) 60 sFAST * 10.0 m/min (32.8 ft/min) 0 s

Operation DescriptionLEVEL (1) * Distance from Low Calibration Point to material surfaceSPACE (2) Distance from High Calibration Point to material surface

DISTANCE(3) Distance from Sensor Reference Point to material surface

Parameter View Edit modeSelect vessel construction material.

Options* STEEL

CONCRETE

Sets the reaction speed of the device to measurement changes in the target range.

Sensor measurement units.

Values m, cm, mm, ft, inDefault: m

sensor reference point (flange face)

High Cal. Pt. Distance

Space

Low Cal. Pt.

Level


mm

mm

m

English

Low Calibration Point

High Calibration Point

Wizard Complete

To transfer Quick Start values to the device and return to Program menu, press (Finish). Then press to return to Measurement mode.

SITRANS LR560 Communications: PROFIBUS PA

Configuring the PROFIBUS PA masterTo configure SITRANS LR560 on the network, you will need the GSD file SIEM816B.gsd. You can download the file from the product page of our web site at: www.siemens.com/LR560. Go to Support > Software Downloads.

SIMATIC PDMWe recommend that you use SIMATIC Process Device Manager (PDM) to program your device. Please consult the operating instructions or online help for details on using SIMATIC PDM. You can find more information at www.siemens.com/simatic-pdm.

Check the support page of our website to make sure you have the latest version of SIMATIC PDM, the most recent Service Pack (SP) and the most recent hot fix (HF). Go to:

https://support.automation.siemens.com/WW/llisapi.dll?func=cslib.csinfo&lang=en&siteid=csius&aktprim=0&extranet=standard&viewreg=WW&objid=10806857&treeLang=en

Options BACK, CANCEL, FINISH (Display returns to 1.1 Quick Start Wizard menu when Quick Start is successfully completed.)

Notes: The following instructions assume that the user is familiar with PROFIBUS PA. You will need the full manual to acquire the list of applicable parameters. Application Guides for setting up PROFIBUS PA devices with SIMATIC PDM can be down-

loaded from the product page of our website at: www.siemens.com/LR560. Go to Support > Software Downloads.

Distance from Sensor Reference Point to Low Calibration Point: usually process empty level.

ValuesRange: 0.000 to 40.000 m or 0.000 to 100.000 m

Default: 40.000 or 100.000 m

Distance from Sensor Reference Point to High Calibration Point: usually process full level.

ValuesRange: 0.000 to 40.000 m or 0.000 to 100.000 m

Default: 0.000 m


mm

mm

m

Engl

ish

Electronic Device Description (EDD)You can locate the EDD in Device Catalog, under Sensors/Level/Echo/Siemens AG/SITRANS LR560.

To install a new EDD Go to www.siemens.com/LR560 > Support > Software Downloads to download the most

up-to-date EDD. Save the files to your computer and extract the zipped file to an easily accessed location. Launch SIMATIC PDM Manage Device Catalog, browse to the unzipped EDD file and

select it.

Configuring a new device1) Set Address via the device push buttons (default 126).

In PROGRAM mode, navigate to: Level Meter > Communication (5)> Device Address (5.1).

Press twice to open parameter view and enable Edit mode. If required, key in a new value and press to accept it. The LCD displays the new

value. Press to return to Measurement mode.

2) Launch SIMATIC PDM and create a new project for LR560. Upload parameters to the PC/PG.3) Configure the device via the Quick Start wizard.

Quick Start Wizard via SIMATIC PDM

Operating via FDT (Field Device Tool)FDT is a standard used in several software packages designed to commission and maintain field devices. Two commercially available FDTs are PACTware and Fieldcare.To configure a field device via FDT you need the DTM (Device Type Manager) for the device. Siemens instruments use SITRANS DTM and an instrument EDD written for SITRANS DTM.1) First install SITRANS DTM on your system. You can download it from:

http://support.automation.siemens.com. Click on Product Support, and navigate to Product Information/Automation Technology/Sensor systems/Process Instrumentation/Software & Communications.

2) Install the SITRANS LR560PROFIBUS PAEDD for SITRANS DTM. You can download it from the product page of our website at: www.siemens.com/LR560. Go to Support > Software Downloads.

Configuring a new device via FDTAn Application Guide can be downloaded from the product page of our website under Support.

Notes: The Quick Start wizard settings are inter-related and changes apply only after you click on

FINISH AND DOWNLOAD at the end of the last step, to save settings offline and transfer them to the device.

Click on BACK to return and revise a setting or Cancel to exit the Quick Start.

Quick Start

Launch SIMATIC PDM, open the menu Device Wizard - Quick Start, complete all the steps, then press Finish and Download.

http://www.siemens.com/LR250


mm

mm

m

English

MaintenanceSITRANS LR560 requires no maintenance or cleaning under normal operating conditions. If cleaning becomes necessary:1) Note the antenna material and the process medium, and select a cleaning solution that

will not react adversely with either.2) Remove the device from service and wipe the antenna clean using a cloth and suitable

cleaning solution.

Unit Repair and Excluded LiabilityFor detailed information, please see the inside back cover.

Temperature De-Rating Curve

WARNING: Never attempt to loosen, remove or disassemble process connection or instrument housing while vessel contents are under pressure.

Process Temperature (C)

Am

bien

t Tem

pera

ture

(C)

high temperature

version

standard version


mm

mm

m

Engl

ish

Wiring setups for hazardous area installationsThe following wiring options are available for hazardous area installations:

Non-Sparking/Energy Limited wiring (Europe) and Dust Ignition Proof wiring (Europe/International) on page 16

Non-incendive and Dust Ignition Proof wiring (US/Canada) on page 17

In all cases, check the device label on your instrument, and confirm the approval rating.

PLC configuration with PROFIBUS PA for hazardous areas

1) Non-Sparking/Energy Limited wiring (Europe) and Dust Ignition Proof wiring (Europe/International)

For power demands see Temperature De-Rating Curve on page 15. For wiring requirements follow local regulations. See also Instructions Specific to Hazardous Area Installations on page 17 and the ATEX

certificate listed above.

Hazardous Area

Non-hazardous Area

PLC (active)

DP/PA coupler

PDM

SITRANS LR560 PA

SITRANS LR560 PA

SITRANS LR560 PA

The ATEX certificate listed on the device label can be downloaded from the product page of our website at: www.siemens.com/LR560. Go to Support > Approvals/Certificates.

The IECEx certificate listed on the device label can be viewed on the IECEx website. Go to: http://iecex.iec.ch and click on Ex Equipment Certificates of Conformity then enter the certificate number IECEx SIR 09.0149X.

Device label (ATEX/IECEx/INMETRO/C-TICK)


mm

mm

m

English

2) Non-incendive and Dust Ignition Proof wiring (US/Canada)

For power demands see Temperature De-Rating Curve on page 15.

Instructions Specific to Hazardous Area Installations (Reference European ATEX Directive 94/9/EC, Annex II, 1.0.6)

The following instructions apply to equipment covered by certificate numbers Sira 09ATEX9356X and Sira 09ATEX4357X:

1) For use and assembly and details of marking/coding, refer to the main instructions.2) The equipment is certified for use as Category 1D, 1/2D and 2D equipment per certificate

Sira 09ATEX9356X and may be used in hazardous zones 20, 21 and 22. The equipment is also certified for use as Category 3G equipment per certificate Sira 09ATEX4357X and may be used in hazardous zone 2.

3) This equipment has a maximum surface temperature of 139 C (in an 80C ambient). Refer to the applicable code of practice for selection of this equipment with respect to specific dust ignition temperatures.

4) The equipment is certified for use in an ambient temperature range of 40 C to 80 C.

5) The equipment has not been assessed as a safety related device (as referred to by Directive 94/9/EC Annex II, clause 1.5).

6) Installation and inspection of this equipment shall be carried out by suitably trained and authorized personnel in accordance with the applicable code of practice.

7) The equipment shall be installed such that the supply cable is protected from mechanical damage. The cable shall not be subjected to tension or torque. The equipment manufacturer is not responsible for providing the supply cable.

8) Repair of this equipment shall be carried out by suitably trained and authorized personnel in accordance with the applicable code of practice.

FM/CSA Class 1, Div 2 connection drawing number A5E02795836 can be downloaded from the product page of our website at: www.siemens.com/LR560 under Support.

Device label (FM/CSA)


mm

mm

m

Engl

ish

Special Conditions for Safe Use

The X suffix to the certificate number relates to the following special condition(s) for safe use: Parts of the enclosure may be non-conducting and may generate an ignition-capable

level of electrostatic charge under certain extreme conditions. The user should ensure that the equipment is not installed in a location where it may be subjected to external conditions (such as high-pressure steam), which might cause a build-up of electrostatic charge on non-conducting surfaces.

The end user must ensure that an ingress protection of at least IP65 is maintained at each entry to the enclosure by use of a blanking element or cable entry device that meets the requirements of the protection concepts type n or increased safety e or flameproof d.

The supply to the equipment shall be rated for a prospective short-circuit current of not more than 10 kA and shall protected by a suitably-rated fuse.

A5E32043113 SITRANS LR560 (PROFIBUS PA) Str. CS-1

mm

mm

m

esky

SITRANS LR560 (PROFIBUS PA)Manul rychlho uveden do provozu Tento manul obsahuje zkladn vlastnosti a funkce zazen SITRANS LR560 (PROFIBUS PA). Velmi doporuujeme pouvat detailn verzi manulu, abyste mohli vyut vechny monosti zazen. Kompletn manul SITRANS LR560 lze sthnout z naich webovch strnek: www.siemens.com/LR560.) Titnou verzi manulu obdrte od svho obchodnho zstupce Siemens Milltronics.Dotazy k obsahu tohoto manulu zaslejte na adresu:

Siemens AGSiemens Milltronics Process Instruments1954 Technology Drive, P.O. Box 4225Peterborough, Ontario, Canada, K9J 7B1Email: [email protected]

MILLTRONICS je registrovan ochrann znmka firmy Siemens Milltronics Process Instruments.

Technick podporaSluba technick podpory je dostupn 24 hodin denn. Adresu, telefonn slo a slo faxu nejbli poboky Siemens Automation Office najdete na strnce: www.siemens.com/automation/partner:

Kliknte na Contact (Kontakty), vyberte Service (Sluby), opakovanm kliknutm na Service budete moci vybrat skupinu do kter pat vae zazen (+Automation Technology (Automatizan technologie) > +Sensor Systems (Detekn systmy) >+Process Instrumentation (Nstroje pro vrobu) > +Level Measurement (Men hladiny) > +Continuous (Prbn)). Vyberte sloku Radar.

Vyberte postupn zem, region a msto. Vyberte Technical Support (Technick podpora) pod zlokou Service.

On-line technickou podporu mete kontaktovat pes: www.siemens.com/automation/support-request

Zadejte nzev produktu (SITRANS LR560) nebo objednac slo a kliknte na Search (Hledat), nsledovn vyberte vhodn typ zazen. Kliknte na Next (Dal).

Zadejte klov slovo vztahujc se k vaemu dotazu. Nsledovn proberte nalezenou dokumentaci nebo kliknte na Next (Dal) pro zasln vaeho dotazu tmu Technick podpory Siemens pomoc elektronick poty.

Centrum Technick Podpory Siemens IA/DT : telefon: +49 (0)911 895 7222

Copyright Siemens AG 2013. Vechna prva vyhrazena Prohlen o zodpovdnosti

Doporuujeme uivatelm nkup autorizovanho titnho manulu nebo staen elektronick verze navren a autorizovan firmou Siemens Milltronics Process Instruments. Firma Siemens Milltronics Process Instruments nen zodpovdn za obsah sten nebo kompletn kopie jak titn nebo elektronick verze manulu.

Akoliv jsme ovili shodu obsahu manulu s popisovanm zazenm, me dochzet ke zmnm. Proto nememe zaruit plnou shodu. Obsah tohoto manulu je pravideln revidovn a opravovn v kadm nsledujcm vydn. Vtme vechny nvrhy k jeho zlepen.

Technick daje podlhaj zmn.

Str. CS-2 SITRANS LR560 (PROFIBUS PA) A5E32043113

mm

mm

m

es

kyBezpenostn pokynyVarovn pokyny mus bt respektovny, aby byla zajitna bezpenost obsluhy a ostatnch osob stejn jako ochrana vrobku a souvisejcho zazen. Tyto varovn pokyny jsou doprovzeny popisem rovn hrozcho nebezpe.

FCC shodaPouze pro instalaci v USA: Pedpisy FCC (Federal Communications Commission)

Industry Canadaa) Provoz zazen je podmnn dvma nsledujcmi podmnkami: (1) zazen nesm

ruiv psobit, a (2) zazen mus snst jakkoliv ruen, vetn ruen produkovan nevhodnm pouvnm samotnho zazen.

b) Toto zazen mus bt instalovno a provozovno v pln uzaven skni, aby bylo zabrnno emism rdiovch vln a nemohlo dojt k ruen leteck navigace. Instalovat zazen me pouze vykolen pracovnk, a pi striktnm dodrovn pokyn vrobce.

c) Zazen je navreno na principu bez ochrany ruen. - Uivatel mus tud akceptovat innost vysoce vkonnch radar ve stejnm frekvennm psmu, co me vst k ruen nebo pokozen tohoto zazen. Na stran druh je uivatel odpovdn za odstrann na vlastn nklady jakhokoliv zazen k monitorovn hladiny, kter by ruilo dve koncesovan innosti.

POZOR: Vztahuje se k bezpenostnm symbolm na vrobku: Zanedbn nezbytnch bezpenostn opaten me mt za nsledek smrt, vn zrann a znan materiln kody.POZOR: Tento symbol je pouvn v ppad, e neexistuje odpovdajc varovn symbol na vrobku. Zanedbn nezbytnch bezpenostnch opaten me mt za nsledek smrt, vn zrann a znan materiln kody.

Poznmka: Oznamuje dleitou informaci o vrobku i jeho sti v uivatelsk pruce.

POZOR: Zmny nebo pravy vslovn neproveden firmou Siemens Milltronics by mohly vst k omezen oprvnn uivatele udrovat zazen v innosti.

Poznmky: Toto zazen bylo testovno a spluje limity tdy A digitlnho zazen, podle l. 15

pedpis FCC. Tyto limity jsou navreny tak, aby zajistily rozumnou ochranu proti kodlivmu psoben, je-li zazen komern vyuvno.

Toto zazen generuje, vyuv a me vyzaovat vysokofrekvenn vlny a pokud nen instalovno podle pokyn manulu, me ruiv psobit na rdiovou komunikaci. innost zazen v obytnch oblastech by mohla ruiv psobit na rdiovou komunikaci. V takovm ppad mus uivatel odstranit toto ruen na vlastn nklady.


mm

mm

m

esky

d) Zazen k men hladiny sm bt instalovno pouze v uzaven skni. Instalujc/uivatel zazen zajist, aby bylo zazen vzdleno nejmn 10 km od radioastronomick stanice Penticton (Britsk Kolumbie, zempisn ka: 49 19' 12" N, zempisn dlka: 119 37'12" W). U zazen, kter nevyaduj 10 km vzdlenost (nap. Okanagan Valley, Britsk Kolumbie), se mus instalujc/uivatel ped instalac a uvedenm zazen do provozu spojit s editelem radioastronomick stanice Penticton za elem obdren jeho psemnho souhlasu. Telefonn kontakt stanice Penticton: 250-493-2277/ fax: 250-493-7767. (V ppad obt lze t kontaktovat Managera, Radio Equipment Standards, Industry Canada.)

Soulad s R&TTE (Evropa)Siemens Milltronics Process Instruments prohlauje tmto, e SITRANS LR560 spluje zkladn poadavky a ostatn pslun ustanoven smrnice 1999/5/ES.LR560 vyhovuje poadavkm EN 302 372 pro pouit v uzavench ndobch, pokud bylo instalovno v souladu s instalanmi poadavky EN 302 372, a me tud bt pouito ve vech zemch EU.

LR560 vyhovuje poadavkm Nvrhu ETSI EN 302 729 pro pouit vn uzavench ndob ve vtin zem EU. (Seznam vjimek naleznete v Prohlen o shod LR560 s EN 302 729, kter je dostupn na webu na adrese www.siemens.com/LR560.) Pi instalaci pod irm nebem mus bt dodreny nsledujc podmnky:

Instalace a drba jsou zajitovny kvalifikovanm a vykolenm personlem.LR560 sm bt instalovno pouze ve stl a pevn poloze smrem k zemi. Jeho umstn mus splovat nsledujc dv omezen:

1) Mus bt vzdleno nejmn 4 km od ne uvedench radioastronomickch stanic, pokud odpovdn sttn regulan orgn nevydal speciln vjimku.

2) Pokud je umstno ve vzdlenosti mezi 4 a 40 km od jedn z ne uvedench radioastronomickch stanic, nesm bt LR560 instalovno ve ne 15 m od zem..

Prohlen o shod LR560 je dostupn na webu na adrese www.siemens.com/LR560.

Zem Nzev stanice Zempisn ka Zempisn dlka

FranciePlateau de Bure 443801 N 055426 E


Nmecko Effelsberg 503132 N 065300 E

Itlie Sardinie 392950 N 091440 E

panlskoYebes 403127 N 030522 W

Pico Veleta 370358.3 N 032333.7 W

vdsko Onsala 572345 N 115535 E

http:/http:/http:/


mm

mm

m

es

kySITRANS LR560

SITRANS LR560 je dvoukanlov impulsn vysla v radarovm psmu 78 GHz FMCW pro prbn monitorovn hladiny tuhch hmot ve skladovacch silech do 100 m (329 ft). Dky koncepci "plug and play" je ideln pro pouit s jakoukoliv sypkou hmotou a to i v extrmn pranm prosted a pi vysokch teplotch do +200 C (+392 F).

Zazen spov v elektronickm obvodu napojenm na okovou antnu s prubou, umoujc rychl a snadn polohovn.

SITRANS LR560 podporuje komunikan protokol PROFIBUS PA, a software SIMATIC PDM . Signly jsou zpracovny pomoc softwaru Process Intelligence.

SpecifikaceKompletn vpis najdete v manulu SITRANS LR560 (PROFIBUS PA). Informace o homologaci naleznete ne Homologace na str. 5.

Teplota prosted/pracovn

Napjen Napjen sbrnicovou linkou 9 a 32 V= pes IEC 61158-2 (PROFIBUS PA) Pkon proudu 13,5 mA

POZOR: SITRANS LR560 me bt uvno pouze podle zsad uvedench v tomto manulu, jinak by mohlo dojt k pokozen bezpenostnch funkc zazen.

Poznmka: Toto zajen je koncipovan pro pouit v prmyslovch oblastech. Jeho pouvn v obytnch oblastech me mt za nsledek ruen radiokomunikanch signl.

Poznmky: Referenn graf uveden na vrobnm ttku lze sthnout z webovch strnek firmy

Siemens na adrese: www.siemens.com/LR560 pod zlokou Support (Podpora). Maximln a minimln teploty zvis na materilu technologickho spoje, antny a

tsnicho krouku. Pouit polohovacho kloubu Easy Aimer limituje maximln ppustnou teplotu.

Viz Graf snenho tepelnho namhn na str. 15 pro podrobnj daje.

pracovn teplota na technologickm spoji: 40 oC a +100 oC (40 oF a +212 oF) nebo 40 oC a +200 oC (40 oF a +392 oF) dle verze

teplota prosted(vn zazen)

40 C a 80 C (40 F a 176F)

vrobn ttek pstroje

Relevantn tlakov a teplotn daje


mm

mm

m

esky

Homologace

Veobecn CSAUSA/C, FM, CE, C-TICK Rdiov vlny R&TTE (Evropa), FCC, Industry Canada Nebezpen prosted

Nejiskiv/S omezenm pkonem 1) (Evropa) ATEX II 3G Ex nA/nL IIC T4 Gc(Brazlie) INMETRO: DNV 12.0085 X

Ex nA IIC T4 Gc-40oC Ta +80 oCUn = 32 VccDNV #OCP 0017ABNT NBR IEC 60079-0:2008,ABNT NBR IEC 60079-15:2012

Ochrana proti vzncen prachu1) (Evropa/mezinrodn)ATEX II 1D, 1/2D, 2DIECEx SIR 09.0149XEx ta IIIC T139oC Da

(Brazlie) INMETRO: DNV 12.0085 XEx nA IIC T4 Gc-40oC Ta +80 oCDNV #OCP 0017ABNT NBR IEC 60079-0:2008 eABNT NBR IEC 60079-31:2011

Ochrana proti vzncen prachu 2) (USA/Kanada)FM/CSATda II, Div. 1, Skupiny E, F, GTda III T4

Nezpaln zazen2) (USA/Kanada)FM/CSA Tda I, Div. 2, Skupiny A, B, C, D, T4

Pouiteln tlak

Smrnice o tlakovch zazench STZ 97/23/EC

Radarov zazen k monitorovn hladiny SITRANS LR560 spad do pole psobnosti lnku 3, sekc 1&2 Smrnice o tlakovch zazen (STZ 97/23/ES), jako tlakov psluenstv I. kategorie. Nicmn, ve smyslu lnku 3, sekce 3 STZ 97/23/ES, je toto zazen koncipovno a vyrobeno v souladu se sprvnou technickou prax (STP) (viz Pokyny Komise EU 1/5).

Poznmky: Na vrobnm ttku jsou uvedeny homologace vztahujc se na dan zazen. Pouvejte vhodn kabelov prchodky, aby byl dodren pedpis IP nebo NEMA.

1) Viz t Zapojen nejiskiv/s omezenm pkonem (Evropa) a zapojen zabraujc vzncen prachu (Evropa/mezinrodn) na str. 16

2) Viz t Nezpaln zapojen a zapojen zabraujc vzncen prachu (USA/Kanada) na str. 17

POZOR:

Nesnate se odpojovat, odmontovat nebo rozebrat technologick spoj i plt zazen pokud je skladovac silo pod tlakem.

Nevhodn instalace me vst ze ztrt pracovnho tlaku.

Poznmka: Vztahuje se pouze na tlakov verze.


mm

mm

m

es

kyInstalace

Umstn hrdlahel zen

hlem zen se rozum hel, ve kterm je intenzita vyzaovanho paprsku polovin oproti maximln intenzit zen.

Intenzita vyzaovanho paprsku je maximln v ose antny.

Pstroj samozejm vyzauje i vn hlu zen, ale tento signl me vst k chybnmu men.

Kuel zen Zajistte, aby kuel zen nebyl ruen

ebky, potrubm, I-nosnky nebo proudy materilu.

Nepouvejte stedov umstn v ppad vysokho a zkho sila.

Pracovn prosted Zajistte snadn pstup pro sledovn

displeje a pro programovn pomoc penosnho programtora.

Zajistte dostaten msto pro konstrukci a kryt zazen.

POZOR: Instalace me bt provedena pouze kolenmi pracovnky v souladu s mstnmi

pedpisy. Nikdy se nesnate odpojovat, odmontovat nebo rozebrat technologick spoj i

plt zazen pokud je skladovac silo pod tlakem. Uivatel je odpovdn za volbu vhodnho spojovacho a tsncho materilu pod

prubu, v zvislosti na vyuit zazen a na pracovnch podmnkch. Nevhodn instalace me vst ze ztrt pracovnho tlaku.Poznmka: Jednotky SITRANS LR560 jsou tlakov otestovny, a pinejmenm spluj poadavky zkonu ASME o kotlch a tlakovch ndobch a poadavky Evropsk smrnice o tlakovch zazench.

kuel zen

4


mm

mm

m

esky

Slunn clonaPokud je zazen LR560 instalovno na pmm slunci, lze stnit displej pomoc voliteln slunen clony.

Sezen zamovae

3" pruba 4" i 6" pruba

1) 4" a 6" zamova: Uvolnte zajitovac rouby na aretanm krouku. Uchopte pevn plt elektronickho zazen a uvolujte aretan krouek zamovae pomoc dodanho C-kle, dokud LR560 mrn nepoklesne. Pltm lze nyn lehce hbat.

2) Je-li to mon, seite SITRANS LR560 tak, aby antna smovala kolmo k povrchu materilu.

3) Jakmile nastavte poadovanou pozici, uthnte aretan krouek pomoc C-kle a nsledn uthnte zajitovac rouby.

4) Pro 3" zamova nabzme pro polohovn roub a matic kolmo k povrchu pruby ikm dl podloky pro rzn hodnoty tlaku.

Zamova Zamen nen nutn pro optimalizaci signlu s kmitotem 78 GHz.

Zamen usnadn men hladiny materilu kuelem en.


mm

mm

m

es

kySystm itn vzduchemistc proudn vzduchu je koncipovno tak, aby vytvolo siln vzdun ven, kter neprodlen oist povrch oky. Vce podrobnost naleznete v kompletnm manulu.

Elektrick instalaceNapjen

Pipojen zazen SITRANS LR560

1) Uvolnte aretan roub.2) Sejmte vko LR560. 3) Vyjmte voliteln displej jeho opatrnm otoenm o

90 ve smru hodinovch ruiek, m se uvoln.4) Obnate plt kabelu cca. 70 mm (2.75") od jeho

konce, a prostrte vodie skrz prchodku 1).

5) Pipojte vodie na svorky dle vyobrazen: SITRANS LR560 (PROFIBUS PA) nen zvisl na polarit.

6) Uzemnte zazen v souladu s mstnmi pedpisy.

7) Uthnte prchodku aby bylo zarueno jej utsnn.

8) Nainstalujte voliteln displej zpt.9) Po konfiguraci a naprogramovn zazen

nasate zpt vko a zajistte jej aretanm roubem.

POZOR:Na svorky stejnosmrnho napjen me bt pipojen pouze zdroj vybaven elektrickou izolac mezi vstupem a vstupem, splujc bezpenostn poadavky IEC 61010-1.

Veker provozn veden mus mt izolaci vhodnou pro jmenovit napt.

POZOR: Ovte si odpovdajc pedpisy na vrobnm ttku zazen. Pouvejte vhodn kabelov prchodky, aby byl dodren pedpis IP nebo NEMA. Viz Pokyny specifick pro instalaci v nebezpenm prosted na str. 17.Poznmka: Detailn instrukce k zapojen naleznete v kompletnm manulu.

1) Jestlie jsou kabely vedeny potrubm, pouvejte pouze vyhovujc chytky, schvlen pro vodotsn pouit.

1)

2)

3) 90

kabelov prchodka (nebo kabelov hrdlo NPT)

ochrann vodi

svorka ochrannho vodie


mm

mm

m

esky

Zapojen zazen na PROFIBUS PA Aby PROFIBUS PA pracoval sprvn, mus bt vhodn ukonen na obou krajnch

koncch sbrnicov linky. Obratte se prosm na uivatelsk a instalan pokyny PROFIBUS PA (objednac slo

2.092), dostupn na www.profibus.com, pro jakkoliv informace ohledn instalace zazen PROFIBUS.

Pokud je zazen napojen na Weidmller nebo na jin propojovac prvek limitujc proud, zkontrolujte zda je tento limit nastaven na 40 mA nebo vce.

Zkladn PLC konfigurace s PROFIBUS PA

Schma zapojen v nebezpenm prosted Viz Schma zapojen v nebezpenm prosted na str. 16

Programovn SITRANS LR560 Viz Sputn Prvodce rychlm uvedenm do provozu pes tlatka RLD na str. 11. Viz Sputn Prvodce rychlm uvedenm do provozu pes SIMATIC PDM na str. 14.

Uveden SITRANS LR560 do provozuZapnte zazen. Bhem zpracovvn prvnho men se nejprve zobraz uvtac obrazovka s logem Siemens, nsledn se na obrazovce zobraz aktuln verze firmware. SITRANS LR560 se automaticky spust v mcm mdu. Pi prvn konfiguraci zazen budete vyzvni k volb uivatelskho jazyka (Anglitina, Nmina, Francouztina, panltina nebo ntina).

Rozhran loklnho displeje (RLD)Zmna parametr pomoc tlatek RLD.(Bezdrtov penosn programtor Siemens lze objednat zvlt pod kat. .. 7ML1930-1BK)

PROFIBUS PA

PROFIBUS DP

DP/PA spojova

aktivn PLC

PC/notebook

PDM

SITRANS LR560 PA

SITRANS LR560 PA

SITRANS LR560 PA


mm

mm

m

es

kyLCD displejZobrazen displeje v mcm mdu (normln innost)

1)

Indikace poruchy

Zobrazen v programovacm mdu

Pi navigaci Ptomnost sloupce navigace v

menu indikuje e seznam poloek v danm menu je pli dlouh aby byl cel zobrazen na displeji.

Vka pruhu aktuln poloky na sloupci navigace znzoruje dlku seznamu poloek danho menu: m ir pruh tm je mn poloek v menu.

Poloha pruhu aktuln poloky na sloupci navigace znzoruje jej piblinou polohu v seznamu poloek danho menu. Pruh situovn v polovin vky sloupce indikuje e tato poloka je piblin uprosted seznamu poloek danho menu. m ir pruh tm je mn poloek v menu.

1) Pepnejte stisknutm nebo .

Poznmka: Detailn rozpis parametr naleznete v kompletnm manulu.

1 indiktor pepnn1) mezi AIFB 1 a AIFB 22 identifikace AIFB zdrojem sledovan hodnoty 3 namen hodnota (rove hladiny, prostor nebo

vzdlenost)4 jednotka5 sloupcov graf znzorujc hodnotu6 textov dek zobrazuje stavov zprvy 7 indikace stavu zazen

67

1 3 42

5

S: 0 LOEV ppad poruchy na zazen se na textovm dku zobraz kd chyby a zprva o porue (7), a indikace stavu zazen zobraz ikonku nutn drby (8)

slo aktuln poloky

aktuln poloka

aktuln menu

pruh poloky

sloupec navigace v menu

hodnota/volba parametru

slo parametru

nzev parametru

Pi editaciPi zmn parametr


mm

mm

m

esky

Programovac mdPomoc tlatek na RLD nejprve stisknte , m vstoupte do Progamovacho mdu a zobrazte menu 1. rovn. Pohybujte se po nabdce v menu pomoc , , , .

Zadn hodnoty

1) Navigujte k poadovanmu parametru, napklad Low Calibration point (Doln kalibran bod - 2.3.1), a opakovanm stisknutm jej otevete a editujte. Aktuln hodnota je zvraznna.

2) Stisknutm nebo smate zvraznnou hodnotu.3) Pi zvraznn ikon Enter pidejte slici stisknutm .4) Pomoc nebo mete zmnit zvraznnou hodnotu. Desetinnou teku naleznete

rolovnm za slici 9.5) Stisknutm zvolte a zvraznte znamnko plus i minus. Pomoc nebo jej

mete zmnit. 6) Stiknte dlouze , a se ikona Enter zvrazn. Nsledn pidejte slici zprava

stisknutm .7) Kdy je zadan sprvn hodnota, stisknte dlouze , a se ikona Enter zvrazn.

Nsledn potvrte hodnotu stisknutm .

Modifikace textovho etezce1) Navigujte k parametru, kter chcete zmnit, a stisknte pro jeho editaci. Textov

etezec je zvraznn.2) Obdobn kroky jako v pedelm odstavci vm umon pidat, vymazat i zmnit

psmena.

Sputn Prvodce rychlm uvedenm do provozu pes tlatka RLD1. Rychl uveden do provozu (Quick Start)

1.1. Prvodce rychlm uvedenm do provozu (Quick Start Wizard)

1) Stisknte dvakrt pro navigaci do Quick Start (1.) a sputn Quick Start Wizard (1.1.)

2) Pi kadm kroku bu stiknte , m akceptujete vchoz hodnoty a peskote k nsledujc poloce, nebo stisknte pro oteven Editanho mdu: Aktuln volba je zvraznna.

3) Rolujte k poadovan poloce, stiskem ulote provedenou zmnu, a pokraujte stiskem .

4) Kdykoliv se mete vrtit o krok zpt stisknutm , nebo zruit editaci a vrtit se do micho mdu stisknutm .

Poznmka: Pokud je ikona Enter zvraznna, stisknutm pidte slici zprava, smaete posledn slici vpravo, potvdte hodnotu, i zrute volbu.

Poznmka: Vchoz hodnoty jsou v ne uvedench tabulkch oznaeny hvdikou (*), nejsou-li vslovn popsny.


mm

mm

m

es

kyNdoba

Citlivost odezvy

Nastavte vt rychlost reakce ne je maximln rychlost plnn i vyprazdovn ale ne pli. Jednotky

Pracovn md

Citlivost odezvy Rychlost plnn i vyprazdovn ndoby za minutu asov konstanta filtru

SLOW (Pomal) 0,1 m/min (0,32 ft/min) 600 sMED (Stedn) 1,0 m/min (3,28 ft/min) 60 sFAST (Rychl) * 10,0 m/min (32,8 ft/min) 0 s

Pracovn md PopisLEVEL (Hladina) (1) * Vzdlenost povrchu materilu od dolnho kalibranho boduSPACE (Prostor) (2) Vzdlenost povrchu materilu od hornho kalibranho bodu

DISTANCE(Vzdlenost) (3) Vzdlenost povrchu materilu od referennho bodu senzoru.

Pi zmn parametr Editan mdZadejte konstrukn materil ndoby (sila).

Monosti* STEEL (Ocel)

CONCRETE (Beton)

Zadejte rychlost reakce zazen pi men zmn ve sledovan hodnot.

Jednotky men senzorem.

Hodnoty mm, cm, m, ft, inVychoz: m

referenn bod idla(elo pruby)Horn kalibran bod

VzdlenostProstor

Doln kalibran bod

rovehladiny


mm

mm

m

esky

Doln kalibran bod

Horn kalibran bod

Ukonen pouit Prvodce

Pro penos hodnot nastavench Prvodcem rychlho uveden do provozu zazen a nvrat do programovacho menu stisknte (Ukonit). Nsledn stisknte pro nvrat do Micho mdu.

Komunikan systm SITRANS LR560: PROFIBUS PA

Konfigurace zazen pomoc mastera PROFIBUS PAPro stovou konfiguraci SITRANS LR560 budete potebovat soubor GSD SIEM816B.gsd. Lze jej sthnout z naich webovch strnek www.siemens.com/LR560.) Vyberte Support (Podpora) > Software Downloads (Soubory ke staen).

SIMATIC PDMK programovn vaeho zazen vm doporuujeme pouvat SIMATIC PDM (Process Device Manager programovac nstroj zazen). Prosme respektujte instrukce k pouit SIMATIC PDM obsaen v nvodu nebo na on-line npovd. Vce informac na www.siemens.com/simatic-pdm.Zkontrolujte si na naich webovch strnkch, zda vlastnte nejnovj verzi SIMATIC PDM vetn poslednho Service Pack (SP) a nejnovjho Hot Fix (HF). Zadejte:


MonostiBACK (Zpt), CANCEL (Zruit), FINISH (Ukonit) (Po spnm ukonen Rychlho uveden do provozu se displej vrt do menu 1.1 Prvodce rychlho uveden do provozu.)

Poznmky: Nsledujc instrukce pedpokldaj e je uivatel seznmen s funkcemi PROFIBUS PA. Seznam vech pouitelnch parametr naleznete v kompletnm manulu. Nvod pro nastaven nstroje PROFIBUS PA pes SIMATIC PDM je dostupn na

naich webovch strnkch: www.siemens.com/LR560. Vyberte Support (Podpora) > Software Downloads (Soubory ke staen).

Vzdlenost referennho bodu senzoru od dolnho kalibranho bodu: vtinou pouv metodu nulov hladiny.

Hodnoty

Rozsah men: 0,000 - 40,000 mnebo 0,000 - 100,000 m

Zkladn nastaven: 40,000 m nebo 100,000 m

Vzdlenost referennho bodu senzoru od hornho kalibranho bodu: pouv metodu pln hladiny.

HodnotyRozsah men: 0,000 - 40,000 mnebo 0,000 - 100,000 mZkladn nastaven: 0,000 m


mm

mm

m

es

kyKonfigurtor elektronickho zazen (EDD)Vhodn EDD naleznete v katalogu zazen pod Sensors/Level/Echo/Siemens AG/SITRANS LR560.

Instalace novho souboru EDD: Aktuln verzi EDD sthnete pod: www.siemens.com/LR560 > Support (Podpora) >

Software Downloads (Soubory ke staen). Ulote soubory do vaeho potae a rozpakujte je do snadno dosaiteln sloky. Spustte SIMATIC PDM Manager Device Catalog (katalog konfiguranch nstroj),

najdte a vyberte EDD soubor nlec k vaemu zazen.

Konfigurace novho zazen1) Nastavte adresu pomoc tlatek na zazen (vchoz: 126).

V programovacm mdu otevete: Level Meter (Men hladiny) > Communication (Komunikace) (5) > Device Address (Adresa zazen) (5.1).

Dvojm stisknutm otevete nhled do parametr a spustte Editan md. Jestlie potebujete, zadejte novou hodnotu a stisknte m ji akceptujete.

LCD displej zobrazuje novou hodnotu. Stisknte pro nvrat do Mcho mdu.

2) Spustte SIMATIC PDM a vytvote nov projekt pro LR560. Nahrajte parametry do PC/PG.3) Nastavte zazen pomoc Prvodce rychlm uvedenm do provozu.

Sputn Prvodce rychlm uvedenm do provozu pes SIMATIC PDM

Ovldn pes FDT (Field Device Tool Servisn nstroj pro provozn zazen)FDT je standard pouvan mnoha programovmi balky pro zen a servis provoznch zazen. Dv FDT jsou komern dostupn: PACTware a Fieldcare.Pro konfiguraci provoznho zazen pes FDT potebujete DTM (Device Type Manager) odpovdajc danmu zazen. Siemens instruments pouv SITRANS DTM spolen s nstrojem EDD, vyvinutm pro SITRANS DTM.1) Za prv nainstalujte SITRANS DTM do vaeho systmu. Lze jej sthnout na adrese:

http://support.automation.siemens.com. Vyberte Product Support (Podpora produkt) a zvolte postupn Product Information/Automation Technology/Sensor systems/Process Instrumentation/Software & Communications.

2) Nainstalujte SITRANS LR560 PROFIBUS PAEDD pro SITRANS DTM. Lze jej sthnout z internetovch strnek produktu: www.siemens.com/LR560.) Vyberte Support (Podpora) > Software Downloads (Soubory ke staen).

Konfigurace novho zazen pes FDTNvod k pouit lze t sthnout z internetovch strnek produktu pod volbou Support (Podpora).

Poznmky: Jednotliv parametry Prvodce rychlm uvedenm do provozu spolu souvisej a

proveden zmny budou aktivovny kliknutm na FINISH AND DOWNLOAD (Ukonen a penos dat) na konci poslednho kroku, m ulote zadan parametry a penesete je do zazen.

Kliknutm na BACK (Zpt) se vrtte k pedel poloce pro jej opravu, a kliknutm na Cancel (Zruit) ukonte Rychl uveden do provozu.

Rychl uveden do provozu

Spustte SIMATIC PDM, otevete menu Device (Zazen) Wizard - Quick Start (Prvodce rychlm uvedenm do provozu), provete vechny nleit kroky a stisknte press Finish and Download (Ukonen a penos dat).

http://www.siemens.com/LR250


mm

mm

m

esky

drbaSITRANS LR560 nevyaduje dnou drbu ani itn v normlnch pracovnch podmnkch. Pokud je istn nutn:1) Vnujte pozornost konstruknmu materilu antny a skladovanmu mdiu, a zvolte

istic prostedky kter na n nebudou nepzniv psobit.2) Odstavte zazen z provozu a oistte antnu pomoc tkaniny naputn adekvtn

istic tekutinou.Opravy zazen a vatek ze zruky Viz podrobnosti na vnitn stran krytu.

Graf snenho tepelnho namhn

POZOR: Nikdy se nesnate odpojovat, odmontovvat nebo rozebrat technologick spojen i plt zazen, pokud je obsah ndoby pod tlakem.

Pracovn teplota (C)

Tepl

ota

pros

ted

(C

)

verze pro vysok teplotystandardn verze


mm

mm

m

es

kySchma zapojen v nebezpenm prosted Existuj nsledujc monosti elektrickho zapojen pro nebezpen prosted:

Zapojen nejiskiv/s omezenm pkonem (Evropa) a zapojen zabraujc vzncen prachu (Evropa/mezinrodn) na str. 16

Nezpaln zapojen a zapojen zabraujc vzncen prachu (USA/Kanada) na str. 17

Ve vech ppadech je nutn si ovit odpovdajc pedpisy na vrobnm ttku zazen.PLC zapojen s PROFIBUS PA pro nebezpen prosted

1) Zapojen nejiskiv/s omezenm pkonem (Evropa) a zapojen zabraujc vzncen prachu (Evropa/mezinrodn)

Poadavky napjecho zdroje: viz Graf snenho tepelnho namhn na str. 15. Pi zapojen zazen respektujte mstn pedpisy. Viz t Pokyny specifick pro instalaci v nebezpenm prosted na str. 17 a ve

uveden certifikt ATEX.

Nebezpen prosted

Nevbun prosted

PLC (aktivn)

DP/PA spojova

PDM

SITRANS LR560 PA

SITRANS LR560 PA

SITRANS LR560 PA

Certifikt ATEX uveden na vrobn ttku lze sthnout z internetovch strnek produktu: www.siemens.com/LR560.) Vyberte Support (Podpora) > Approvals (Schvlen) / Certificates (Certifikty).Certifikt IECEx uveden na vrobnm ttku naleznete na internetovch strnkch IECEx Vyberte: http://iecex.iec.ch. Zde vyberte Ex Equipment Certificates of Conformity (certifikty o shod zazen) a zadejte slo certifiktu IECEx SIR 09.0149X.

Vrobn ttek (ATEX/IECEx/INMETRO/C-TICK)


mm

mm

m

esky

2) Nezpaln zapojen a zapojen zabraujc vzncen prachu (USA/Kanada)

Poadavky napjecho zdroje: viz Graf snenho tepelnho namhn na str. 15.

Pokyny specifick pro instalaci v nebezpenm prosted (Viz evropskou smrnici ATEX 94/9/EC, Ploha II, 1.0.6)

Nsledujc pokyny se tkaj zazen spadajc pod certifikty SIRA 09ATEX9356X a SIRA 09ATEX4357X.

1) Vce podrobnost ohledn uvn, instalace, znaen i pouvanch kd naleznete v kompletnm nvodu.

2) Toto zazen je certifikovno pro pouit jako zazen Tdy 1D, 1/2D a 2D certifiktem Sira 09ATEX9356X a me tud bti pouvno v nebezpench prostedch 20, 21 a 22. Zazen je t certifikovno pro pouit jako zazen Tdy 3G certifiktem Sira 09ATEX4357X, a me tud bti pouvno v nebezpenm prosted 2.

3) Maximln teplota povrchu plt zazen je 139 C (pi teplot prosted 80C). Ovte si poadavky platn legislativy vztahujc se na dan zazen s ohledem na specifick teploty samovzncen prachu.

4) Toto zazen je certifikovno pro pouit pi teplot prosted v rozmez -40 C a +80 C.

5) Toto zazen nen koncipovno jako bezpen zazen (ve smyslu Smrnice 94/9/EC, Ploha II, odstavec 1.5).

6) Instalovat a kontrolovat toto zazen mohou pouze vhodn vykolen osoby v souladu s poadavky platn legislativy.

7) Zazen mus bt instalovno tak, aby napjec kabely byly chrnny ped mechanickm pokozenm. Kabely nesm bt natahovny ani krouceny. Vrobce zazen nen odpovdn za dodn napjecch kabel.

8) Opravovat toto zazen mohou pouze vhodn vykolen osoby v souladu s poadavky platn legislativy.

Vkres zapojen FM/CSA Tdy 1, Div. 2, sla A5E02795836, lze sthnout z internetovch strnek produktu na adrese: www.siemens.com/LR560 v sekci Support (Podpora).

Vrobn ttek (FM/CSA)


mm

mm

m

es

kySpecifick podmnky bezpenho uvn Ppona X k slu certifiktu je vztaena ke specifickm podmnkm bezpenho uvn.

Nkter sti plt mohou bt nevodiv a mohou tud v extrmnch podmnkch generovat elektrostatick potencil s rizikem vzncen. Uivatel je povinen zajistit, aby nebylo zazen instalovno v mst kde na nj psob extern vlivy (nap. pra pod vysokm tlakem), kter by mohly zpsobit nrst elektrostatickho potencilu na nevodivch stch.

Konen uivatel mus zajistit, aby veker prchody pltm zazen dodrovaly minimln ochranu proti prachu a vod IP65 pomoc zaslepovacch dl nebo vhodnch kabelovch prchodek v souladu s poadavky koncepce ochrany typu n, resp. zven bezpenosti e i ohnivzdornho zazen d.

Napjen zazen mus bt dimenzovno pro mon zkratov proud do 10 kA a mus bt chrnno vhodn dimenzovanou pojistkou.

A5E32043113 SITRANS LR560 (PROFIBUS PA) Side DA-1

mm

mm

m

Dansk

SITRANS LR560 (PROFIBUS PA) -Kvikstart manualDenne manual opridser de vsentligste karakteristika og funktioner af SITRANS LR560 (PROFIBUS PA). Vi anbefaler Dem kraftigt at anskaffe den detaljerede version af denne manual, s De kan anvende apparatet fuldt ud. Den komplette manual kan downloades fra produktsiden for SITRANS LR560 p vores website: www.siemens.com/LR560. Den trykte manual kan fs hos Deres lokale Siemens Milltronics reprsentant.

Sprgsml vedrrende indholdet af denne manual kan rettes til:Siemens AGSiemens Milltronics Process Instruments1954 Technology Drive, P.O. Box 4225Peterborough, Ontario, Canada, K9J 7B1E-mail: [email protected]

MILLTRONICS er et registreret varemrke, der tilhrer Siemens Milltronics Process Instruments.

Teknisk SupportSupport er tilgngelig 24 timer i dgnet.

Adresse, telefon- og faxnummer p Siemens Automations lokale kontor kan findes p:

www.siemens.com/automation/partner: Klik p fanen Contact (Kontakt), vlg Service og klik derefter en gang til p

Service for at finde den relevante produktgruppe (+Automation Technology (Automatiseringsteknik) > +Sensor Systems (Flersystemer) >+Process Instrumentation (Procesinstrumentering) > +Level Measurement (Niveaumling) > +Continuous (Kontinuert)). Vlg Radar.

Vlg land og derefter by/egn. Vlg Technical Support (Teknisk support) under Service.

For on-line teknisk support, g til: www.siemens.com/automation/support-request Indtast apparatets navn (SITRANS LR560) eller ordrenummeret, klik p Search (Sg) og

vlg den relevante produkttype. Klik p Next. Indtast et ngleord, der beskriver problemet. Gennemlb derefter den relevante

dokumentation eller klik p Next for at e-maile en beskrivelse af problemet til personalet i Siemens Tekniske Support.

Siemens IA/DT Teknisk Support Center: telefonnr. +49 (0)911 895 7222

Copyright Siemens AG 2013. Alle rettigheder forbeholdes Ansvarsfragelse

Vi opfordrer brugerne til at anskaffe de autoriserede, indbundne manualer eller at lse de elektroniske versioner, der er udarbejdet og skrevet af Siemens Milltronics Process Instruments. Siemens Milltronics Process Instruments ptager sig intet ansvar for indholdet af delvise eller fuldstndige gengivelser af indbundne eller elektroniske versioner.

Sknt vi har kontrolleret, at indholdet af denne manual stemmer overens med de beskrevne instrumenter, kan der stadig forekomme variationer. Vi kan derfor ikke garantere en fuldstndig overensstemmelse. Indholdet af denne manual revideres jvnligt, og eventuelle rettelser inkluderes i de efterflgende udgaver. Vi modtager gerne forslag til forbedringer.

Retten til ndringer af de tekniske data forbeholdes.

Side DA-2 SITRANS LR560 (PROFIBUS PA) A5E32043113

mm

mm

m

Dans

k

SikkerhedsvejledningDe anfrte advarsler skal overholdes for at sikre egen og andres sikkerhed samt for at beskytte produktet og det tilknyttede udstyr. Disse advarsler ledsages af en tydeliggrelse af graden af forsigtighed, der br overholdes.

FCC-overensstemmelseKun for installationer i USA: Regler fra Federal Communications Commission (FCC)

Industry Canadaa) Driften er underlagt flgende betingelser: (1) apparatet m ikke bevirke interferens, og (2)

apparatet m kunne acceptere enhver interferens, inklusive interferens, som kan bevirke unsket drift af apparatet.

b) Dette apparat skal installeres og betjenes i en helt lukket beholder for at forhindre udsendelse af radiofrekvenser, som ellers kan virke forstyrrende p luftfartsnavigationen. Installationen skal foretages af trnede installatrer under streng overholdelse af fabrikantens instruktioner.

c) Dette apparat anvendes p en "ingen-interferens, ingen-beskyttelse"-basis. Det betyder, at brugeren skal acceptere driften af hjeffektradar i samme frekvensbnd, som kan forstyrre eller beskadige dette apparat. P den anden side vil niveaumlingsapparater, der viser sig at forstyrre den primre licensdrift, skulle fjernes p brugerens bekostning.

ADVARSEL: vedrrer et advarselssymbol p produktet og betyder, at en manglende overholdelse af de ndvendige forholdsregler kan fre til dd, alvorlig personskade og/eller omfattende materielle skader.ADVARSEL: anvendes, nr der ikke er noget tilsvarende advarselssymbol p produktet, og betyder, at en manglende overholdelse af de ndvendige forholdsregler kan fre til dd, alvorlig personskade og/eller omfattende materielle skader.

Bemrk: betyder vigtige oplysninger om produktet eller denne del af brugervejledningen.

ADVARSEL: ndringer eller modifikationer, der ikke er udtrykkeligt godkendt af Siemens Milltronics, kan ophve brugerens ret til at benytte udstyret.

Bemrk: Dette udstyr er blevet testet og fundet at overholde grnserne for en klasse A digital

anordning i henhold til Afsnit 15 i FCC-reglerne. Disse grnser er beregnet til at yde en rimelig beskyttelse mod skadelige interferenser, nr anordningen anvendes i kommercielle omgivelser.

Dette udstyr frembringer, bruger og kan udstrle radiofrekvent energi, og kan, sfremt det ikke installeres og bruges i overensstemmelse med instruktionsbogen, forrsage interferens, der kan virke forstyrrende for radiokommunikationen. Brugen af dette udstyr i et beboelsesomrde vil sandsynligvis forrsage skadelig interferens med radiokommunikationer, som brugeren i givet fald vil vre ndsaget til at udbedre for egen regning.


mm

mm

m

Danskd) Det er kun tilladt at installere dette niveaumlingsapparat inde i lukkede beholdere.

Installatren/brugeren af apparatet skal sikre sig, at det befinder sig mindst 10 km fra Penticton radioastronomiske station (British Columbia breddegrad: 49 19' 12" N, lngdegrad: 119 37'12" W). For apparater, der ikke opfylder denne afstand p 10 km (f. eks. Okanagan Valley, British Columbia) skal installatren/brugeren henvende sig til og opn en skriftlig tilladelse fra direktren for Penticton radioastronomiske station, fr udstyret kan installeres eller sttes i drift. Kontakt til Penticton er tlf.: 250-493-2277/ fax: 250-493-7767. (I tilflde af vanskeligheder kan der ogs rettes henvendelse til chefen for Radioudstyrsstandarder hos Industry Canada.)

R&TTE Overholdelse (Europa)Siemens Milltronics Process Instruments erklrer hermed, at SITRANS LR560 overholder de vsentlige krav og andre relevante bestemmelser i Direktiv 1999/5/EC.

LR560 overholder EN 302 372 mht. brug i lukkede opbevaringsbeholdere, sfremt apparatet installeres i henhold til installationskravene i EN 302 372, og det m anvendes i alle EU-lande.

LR560 overholder Udkastet ETSI EN 302 729 mht. brug uden for lukkede tanke i de fleste EU-lande. (For en liste over undtagelserne, se LR560 Erklring for EN 302 729, som kan findes online p www.siemens.com/LR560.) Ved installationer i fri luft skal flgende betingelser iagttages:

Installationen og vedligeholdelsen skal udfres af tilstrkkeligt kvalificeret og uddannet personale.LR560 m kun installeres rettet nedad i en permanent, fastlst position. Dets placering skal overholde flgende to begrnsninger:

1) Det skal installeres i en afstand af mindst 4 km fra de nedenfor angivne radioastronomistationer, med mindre den ansvarlige nationale tilsynsmyndighed har givet srlig tilladelse dertil.

2) Sfremt det installeres p et sted, der ligger mellem 4 og 40 km fra en af de nedenfor angivne radioastronomistationer, skal LR560 installeres i en hjde p mindre end15 m over jorden.

Overensstemmelseserklringen for LR560 kan findes online p www.siemens.com/LR560.

Land Stationens navn Geografiske breddegrad Geografisk lngdegrad

FrankrigPlateau de Bure 443801 N 055426 E


Tyskland Effelsberg 503132 N 065300 E

Italien Sardinien 392950 N 091440 E

SpanienYebes 403127 N 030522 W

Pico Veleta 370358.3 N 032333.7 W

Sverige Onsala 572345 N 115535 E

http:/http:/http:/


mm

mm

m

Dans

k

SITRANS LR560

SITRANS LR560 er en 2-trds 78 GHz FMCW radarniveautransmitter til kontinuert overvgning af faste stoffer i beholdere fra en afstand p op til 100 m (329 ft). Med dens plug and play-funktion er den ideel til alle anvendelser med faste stoffer, ogs i tilflde af ekstreme stvforhold og ved hje temperaturer p op til +200 C (+392 F).

Apparatet bestr af et elektronisk kredslb forbundet med en linseantenne og en flange, der tillader en let og hurtig positionering.

SITRANS LR560 understtter PROFIBUS PA kommunikationsprotokol og SIMATIC PDM software. Signaler behandles ved hjlp af Process Intelligence.

Tekniske dataFor en fuldstndig liste, se SITRANS LR560 (PROFIBUS PA) Instruktionsbogen. For oplysninger om godkendelser, se Godkendelser p side 5.

Omgivende temperatur/Driftstemperatur

Strmforsyning Strmforsynes gennem bussen 9 til 32 V DC, iflge IEC 61158-2 (PROFIBUS PA) Strmforbrug 13,5 mA

ADVARSEL: SITRANS LR560 br kun anvendes som beskrevet i denne manual, da den beskyttelse, udstyret yder, ellers kan forringes.

Bemrk: Dette produkt er beregnet til at anvendes i industriomrder. Brugen at dette udstyr i et beboelsesomrde kan forrsage interferens med diverse frekvensbaserede kommunikationsmidler.

Bemrk: Referencetegningen, der er angivet p apparatets skilt, kan downloades fra Siemens'

website p: www.siemens.com/LR560 under Support. Maksimum- og minimumtemperaturerne afhnger af procestilslutningens, antennens og

O-ringens materialer. Maksimumtemperaturen begrnses ved brug af en Easy Aimer. Se Temperatur-underbelastningskurve p side 15 for yderligere detaljer.

procestemperaturen ved procestilslutningen: 40 oC til +100 oC (40 oF til +212 oF) eller 40 oC til +200 oC (40 oF til +392 oF) afhngigt af versionen

omgivelsestemperatur(omkring instrumenthuset)

40 C til 80 C (40 F til 176 F)apparatets skilt

oplysninger vedr. tryk/temperatur


mm

mm

m

Dansk

Godkendelser

Almen brug CSAUSA/C, FM, CE, C-TICK Radio R&TTE (Europa), FCC, Industry Canada Risikoomrder

Ikke-gnistdannende/Energibegrnset 1) (Europa) ATEX II 3G Ex nA/nL IIC T4 Gc

(Brasilien) INMETRO: DNV 12.0085 XEx nA IIC T4 Gc-40 C Ta +80 CUn = 32 VccDNV #OCP 0017ABNT NBR IEC 60079-0:2008, ABNT NBR IEC 60079-15:2012

Stveksplosionssikker1) (Europa/Internationalt) ATEX II 1D, 1/2D, 2DIECEx SIR 09.0149XEx ta IIIC T139oC Da

(Brasilien) INMETRO: DNV 12.0085 XEx ta IIIC T139 C Da IP68-40 C Ta +80 CDNV #OCP 0017ABNT NBR IEC 60079-0:2008 eABNT NBR IEC 60079-31:2011

Stveksplosionssikker 2) (USA/Canada) FM/CSAKlasse II, Div. 1, Gruppe E, F, GKlasse III T4

Ikke-antndingsfarlig2) (USA/Canada) FM/CSA Klasse I, Div. 2, Gruppe A, B, C, D, T4

Anvendelser under tryk

Trykudstyrsdirektivet, 97/23/EF

SITRANS LR560 radarniveaumlingsinstrument ligger under grnserne for et trykbrende udstyr af kategori I i artikel 3, afsnit 1 og 2 i Trykudstyrsdirektivet (97/23/EF). Ikke desto mindre er dette udstyr udviklet og fremstillet i overensstemmelse med God Teknisk Praksis (Sound Engineering Practice - SEP) iflge Trykudstyrsdirektivet, 97/23/EF, artikel 3, afsnit 3 (se EU-Kommissionens vejledning 1/5).

Bemrk: Apparatets skilt angiver de godkendelser, der glder for netop Deres apparat. Brug passende kabelrrsttninger for at bevare IP- eller NEMA-klassificeringen.

1) Se ogs Ikke-gnistdannende/Energibegrnset elinstallation (Europa) og Stvantndelsesbeskyttet elinstallation (Europa/Internationalt) p side 16.

2) Se ogs Ikke-antndingsfarlig og Stvantndelsesbeskyttet elinstallation (USA/Canada) p side 17.

ADVARSLER:

Forsg aldrig at lsne, afmontere eller adskille procestilslutningen eller instrumenthuset, mens indholdet er under tryk.

Ukorrekt installation kan medfre tab af procestryk.

Bemrk: Angr kun versionen til anvendelser under tryk.


mm

mm

m

Dans

k

Installation

Mundstykkets placeringStrlevinkel

Strlevinklen er bredden af keglen, hvor energittheden er halvdelen af den maksimale energitthed.

Den maksimale energitthed er lige ud for og i forlngelse af antennen.

Der udsendes et signal uden for strlevinklen, hvilket kan give anledning til ekkoer fra falske ml.

Emissionskegle Emissionskeglen skal holdes fri for

interferens fra stiger, rr, I-profiler eller pfyldningsstrmme.

Undg centrale placeringer p hje, smalle beholdere.

Omgivelser

Srg for en lettilgngelig adgang for aflsning af displayet og programmering ved hjlp af den hndholdte programmeringsenhed.

Srg for, at omgivelserne svarer til instrumenthusets klassificering og konstruktionsmaterialer.

ADVARSLER: Installationen m kun foretages af kvalificeret personale og under

overholdelse af de lokalt gldende regler. Forsg aldrig at lsne, afmontere eller adskille procestilslutningen eller

instrumenthuset, mens indholdet er under tryk. Brugeren er ansvarlig for at vlge sammenboltnings- og

pakningsmaterialer, der ligger inden for flangens begrnsninger og dens ptnkte anvendelse, og som passer til anvendelsesforholdene.

Ukorrekt installation kan medfre tab af procestryk.

Bemrk: SITRANS LR560-enhederne er trykafprvet og opfylder eller overskrider kravene i ASME Boiler and Pressure Vessel Code samt det europiske Trykudstyrsdirektiv.

emis-sionskegle

4


mm

mm

m

DanskSolskrm

Displayet p LR560 kan beskyttes med en solskrm (ekstraudstyr), sfremt instrumentet skal monteres i direkte sollys

Indstilling vha. Aimeren

3" flange 4 og 6" flange

1) For 4" og 6" Aimer: lsn stskruerne i lseringen. Idet der holdes godt fast i instrumenthuset, lsnes Aimerens lsering ved hjlp af den medflgende ngle, indtil LR560 bevger sig en smule ned. Derefter kan instrumenthuset drejes frit.

2) Ret s vidt muligt SITRANS LR560, s antennens retning er vinkelret p materialets overflade.

3) Nr den nskede position er net, strammes lseringen igen ved hjlp af nglen, og stskruerne strammes.

4) For 3" Aimer flangen medflger koniske fjederskiver med versioner til anvendelse under tryk for at holde mtrikker og bolte vinkelrette p flangens overflade.

Aimer Sigtehjlpen er ikke pkrvet for signaloptimisering med frekvensen 78 GHz.

Sigtehjlpen hjlper til at mle materialet i keglen.


mm

mm

m

Dans

k

RenseluftsystemRenseluftstrmmen er beregnet til at skabe en kraftig lufthvirvel, som hurtigt renser linsens overflade. Se detaljerne i den komplette manual.

Elektrisk installationStrmforsyning

Tilslutning af SITRANS LR560

1) Lsn lseskruen.2) Fjern lget p LR560. 3) Fjern det valgfri display ved forsigtigt at dreje

displayet en kvart omgang mod uret, indtil det er lst.

4) Afisoler kablet p ca. 70 mm (2,75") fra enden af kablet og fr ledningerne gennem pakdsen 1).

5) Forbind ledningerne med klemmerne som vist. SITRANS LR560 (PROFIBUS PA) er ikke polaritetsflsom.

6) Jordforbind instrumentet i henhold til de lokale bestemmelser.

7) Stram pakdsen for at opn en god ttning.8) St det valgfri display tilbage p plads.9) Efter programmering og konfiguration af

apparatet sttes lget tilbage p plads, og lseskruen strammes.

ADVARSLER:DC-indgangsklemmerne skal forsynes fra en kilde, der yder elektrisk isolation mellem ind- og udgang, for at opfylde de gldende sikkerhedskrav i henhold til IEC 61010-1.

Alle felt-elinstallationer skal vre forsynet med en passende isolering i forhold til de nominelle spndinger.

ADVARSLER: Tjek godkendelsesniveauet p apparatets skilt. Brug passende kabelrrsttninger for at bevare IP- eller NEMA-klassificeringen. Ls Srlige anvisninger vedrrende installation i risikoomrder p side 17.Bemrk: For en detaljeret vejledning i elinstallationen henvises der til den komplette instruktionsbog.

1) Hvis kablerne fres gennem kabelrr, brug kun muffer af en passende strrelse, der er godkendt til vandttte applikationer.

1)

2)

3) omgang

pakdse (eller NPT kabelindfring)

kabelaf-skrmning

tilslutning instrument-afskrmning


mm

mm

m

Dansk

Installering af PROFIBUS PA apparater PROFIBUS PA skal termineres i begge ender af kablet for at virke rigtigt. Der henvises til PROFIBUS PA User and Installation Guidelines (Bruger- og

Installationsvejledning) (bestillingsnummer 2.092), der kan fs fra www.profibus.com, for oplysninger om installation af PROFIBUS-apparater.

Hvis der tilsluttes en Weidmller eller anden strmbegrnsende samledse til dette apparat, skal strmbegrnsningen indstilles p mindst 40 mA.

Basal PLC-konfiguration med PROFIBUS PA

Elektriske opstninger ved installationer i risikoomrder Se Elektriske opstninger ved installationer i risikoomrder p side 16.

Programmering af SITRANS LR560 Se Kvikstartguide via LDIens trykknapper p side 11. Se Kvikstartguide via SIMATIC PDM p side 14.

Aktivering af SITRANS LR560Tnd for apparatet. En overgangsskrm viser frst Siemens logo, derefter vises den aktuelle firmware version, mens den frste mling behandles. SITRANS LR560 starter automatisk i Mlingsmode.

Frste gang apparatet konfigureres, bliver De bedt om at vlge et sprog (engelsk, tysk, fransk, spansk eller kinesisk).

Den Lokale Display Interface (LDI)Parametrene ndres ved hjlp af LDIens trykknapper.

(Siemens infrarde hndholdte programmeringsenhed kan bestilles separat: [Del nr. 7ML1930-1BK]).

PROFIBUS PA

PROFIBUS DP

DP/PA-kobler

aktiv PLC

PC/brbar computer

PDM

SITRANS LR560 PA

SITRANS LR560 PA

SITRANS LR560 PA


mm

mm

m

Dans

k

LCD-displayMlingsmode (normal drift)

1)

Indikatorer ved fejl

Display i Programmode

Navigationsskrm En synlig menusjle er tegn p, at

menulisten er for lang til, at alle punkterne kan vises.

Bredden af bndet p menusjlen angiver menulistens lngde: et bredere bnd er tegn p frre punkter.

Bndets position angiver det aktuelle punkts approksimative position i listen. Et bnd halvvejs nede af menusjlen angiver, at det aktuelle punkt er halvvejs nede af listen. Et bredere bnd er tegn p frre punkter.

1) Tryk p eller for at omskifte.

Bemrk: For en fuldstndig liste over parametrene henvises til den komplette manual.

1 indikator for skift1) mellem AIFB 1 og AIFB 22 identificerer, hvilken AIFB, den viste vrdi stammer fra3 den mlte vrdi (level (niveau), space (frirum) eller distance

(afstand))4 enheder5 sjlediagram, der angiver niveauet6 tekstzone, der viser statusmeddelelser 7 apparatets statusindikator67

1 3 42

5

S: 0 LOENr der er en fejl til stede, vises fejlkoden og fejlmeddelelsen i tekstzonen (7), og et ikon for "service pkrvet" tndes i apparatets statuszone (8)

nummer p aktuelt punkt

aktuelt punkt

aktuel menu

bnd

menusjle

parametervrdi/valg

parameternummer

parameter-navn

RedigeringsskrmParameterskrm


mm

mm

m

Dansk

PROGRAM modeVed hjlp af LDIens trykknapper, tryk p for at sl over i Programmode og bne menuniveau 1. Gennemlb menuen ved hjlp af , , , .

Redigering af et tal

1) Naviger hen til den nskede parameter, for eksempel Lavt Kalibreringspunkt (2.3.1), og tryk to gange p for at bne og redigere parameteren. Vrdien vil vre fremhvet.

2) Tryk p eller for at slette den fremhvede vrdi.3) Med Enter-ikonet fremhvet , tryk p for at tilfje et tal.4) Brug eller for at ndre det fremhvede tal. Fortst med

at gennemlbe efter 9 for at finde decimalpunktummet.5) Tryk p for at vlge og fremhve plus- eller minustegnet. Tryk p eller for at

ndre det. 6) Tryk p , indtil Enter-ikonet fremhves , og tryk derefter p for at tilfje et tal p

hjre side.7) Nr vrdien er komplet, tryk p , indtil Enter-ikonet fremhves , og tryk derefter

p for at acceptere vrdien.

ndring af en tekststreng:1) Naviger hen til den parameter, der nskes ndret, og tryk p for at redigere den.

Strengen vil vre fremhvet.2) Flg samme trin som ovenfor beskrevet for at tilfje, slette eller ndre et eller flere tegn.

Kvikstartguide via LDIens trykknapper1. Kvikstart

1.1. Kvikstartguide

1) Tryk to gange p for at navigere hen til Kvikstart (1.) og bne Kvikstartguide (1.1.)

2) P hvert trin trykkes for at acceptere standardvrdierne og g direkte til nste punkt, eller for at bne Redigeringsmode: det aktuelle valg fremhves.

3) Gennemlb punkterne hen til det nskede punkt og tryk p for at gemme ndringen og derefter p for at fortstte.

4) De kan til enhver tid trykke p for at g tilbage eller p for at annullere og vende tilbage til Mlingsmode.

Bemrk: Med Enter-ikonet fremhvet, tryk p for at indstte et tal til hjre, for at slette tallet lngst til hjre, for at acceptere vrdien eller for at annullere.

Bemrk: Standardvrdierne er angivet med en stjerne (*) i nedenstende tabeller, med mindre de er udtrykkeligt beskrevet.


mm

mm

m

Dans

k

Beholder

Svarhastighed

Brug en indstilling, der lige netop er hurtigere end beholderens maksimale fyldnings- eller tmningshastighed (den strste af disse). Enheder

Drift

SvarhastighedBeholderens fyldnings- eller tmningshastighed pr. minut

Filtertidskonstant

SLOW (LANGSOM) 0,1 m/min (0,32 ft/min) 600 sMED (MIDDEL) 1,0 m/min (3,28 ft/min) 60 sFAST (HURTIG) * 10,0 m/min (32,8 ft/min) 0 s

Drift BeskrivelseLEVEL

(NIVEAU) (1)* Afstand fra Lavt kalibreringspunkt til materialets overflade

SPACE (FRIRUM) (2)

Afstand fra Hjt kalibreringspunkt til materialets overflade

DISTANCE (AFSTAND) (3)

Afstand fra Flerens referencepunkt til materialets overflade.

Parameterskrm RedigeringsmodeVlg beholderens konstruktionsmateriale.

Valgmulig-heder

* STEEL (STL)

CONCRETE (BETON)

Indstiller apparatets reaktionshastighed over for ndringer i mlingerne inden for mlomrdet.

Flerens mleenheder.

Vrdier m, cm, mm, ft, inStandardvrdi: m

Flerens referencepunkt (flangensoverflade)

Hjt kalib.pkt.Afstand

Tomrum

Lavt kalib.pkt.

Niveau


mm

mm

m

Dansk

Lavt kalibreringspunkt

Hjt Kalibreringspunkt

Wizard Complete (Guide gennemfrt)

For at overfre Kvikstartvrdierne til apparatet og vende tilbage til Programmenuen, tryk p (Finish (Afslut)). Tryk derefter p for at vende tilbage til Mlingsmode.

SITRANS LR560 Kommunikation: PROFIBUS PA

Konfiguration af PROFIBUS PA masterenFor at konfigurere SITRANS LR560 i netvrket krves GSD-filen SIEM816B.gsd. Denne fil kan downloades fra produktsiden p vort website: www.siemens.com/LR560. G til Support > Software Downloads (Download af software).

SIMATIC PDM Vi anbefaler at bruge SIMATIC Process Device Manager (PDM) til at programmere apparatet. Ls venligst betjeningsvejledningen eller online-hjlpen for oplysninger om brugen af SIMATIC PDM. Flere oplysninger fs p www.siemens.com/simatic-pdm.

Tjek supportsiden p vort website for at sikre Dem, at De har den nyeste version af SIMATIC PDM, den seneste Service Pack (SP) og den seneste hot fix (HF). G til:


ValgmulighederBACK (Tilbage), CANCEL (Annuller), FINISH (Afslut) (Skrmen vender tilbage til Kvikstartguidens menu 1.1, nr Kvikstarten er vel gennemfrt).

Bemrk: I de flgende anvisninger forudsttes det, at brugeren er fortrolig med PROFIBUS PA. Det er ndvendigt at rde over den komplette manual for at have adgang til listen over

mulige parametre. Brugsanvisninger for opstning af PROFIBUS PA-apparater vha. SIMATIC PDM kan

downloades fra produktsiden p vort website: www.siemens.com/LR560. G til Support > Software Downloads (Download af software).

Afstand fra Flerens referencepunkt til Lavt kalibreringspunkt: normalt proces tom-niveau.

VrdierInterval: fra 0,000 til 40,000 m eller fra 0,000 til 100,000 m

Standardvrdi: 40,000 eller 100,000 m

Afstand fra Flerens referencepunkt til Hjt kalibreringspunkt: normalt proces fuld-niveau.

VrdierInterval: fra 0,000 til 40,000 m eller fra 0,000 til 100,000 m

Standardvrdi: 0,000 m


mm

mm

m

Dans

k

Electronic Device Description (EDD - Elektronisk apparatbeskrivelse)EDD kan findes i Apparatkataloget (Device Catalog) under Sensors/Level/Echo/Siemens AG/SITRANS LR560 (Flere/Niveau/Ekko/Siemens AG/SITRANS LR560).

For at installere en ny EDD G til www.siemens.com/LR560 > Support > Software Downloads (Download af

software) for at downloade den nyeste EDD. Gem filerne p computeren og pak den zippede fil ud til en lettilgngelig placering. Start SIMATIC PDM Manage Device Catalog (Administrere Apparatkatalog), find den

udpakkede EDD-fil og vlg den.

Konfiguration af et nyt apparat1) Angiv adressen ved hjlp af apparatets trykknapper (standardvrdien er 126).

I PROGRAM mode, navigr hen til:

sitrans - cache.industry.siemens.com · a5e32043113 sitrans lr560 (profibus pa) page en-1 mmmmm...

Documents