single voltage external power supply test … valentines mini dab radio/test... · single voltage...
TRANSCRIPT
Shenzhen SIT Testing Technology Co., Ltd. Report No.: SIT151211361U
Page 1 of 12
SINGLE VOLTAGE EXTERNAL POWER SUPPLY TEST REPORT
Prepared For : PEAK ELECTRONIC(HUIZHOU)CO., LTD
Add: No.1, Xialuo Road, Zhongkai Hi-tech Area, Huizhou, Guangdong, China
Product Name: DAB/FM radio
Trade Mark N/A
Model : DB-318, DB-318B, DB-318C, DB-318R, DB-318U
Prepared By : Shenzhen SIT Testing Technology Co., Ltd
Add: 4th Floor, Co-talent Creative Park, Liuxian Road, Baoan 68 District, Shenzhen
Test Date: December 14, 2015 to December 22, 2015
Date of Report : December 30, 2015
Report No.: SIT151211361U
Note: This report shall not be reproduced except in full, without the written approval of Shenzhen SIT Testing Technology Co., Ltd. ,This document may be altered or revised by Shenzhen SIT Testing Technology Co., Ltd. personnel only, and shall be noted in the revision section of the document. The test results in the report only apply to the tested sample
Shenzhen SIT Testing Technology Co., Ltd. Report No.: SIT151211361U
Page 2 of 12
TEST REPORT
Report No.: SIT151211361U
Client: PEAK ELECTRONIC(HUIZHOU)CO., LTD
Address: No.1, Xialuo Road, Zhongkai Hi-tech Area, Huizhou, Guangdong, China
Sample Description:
DAB/FM radio
Model: DB-318, DB-318B, DB-318C, DB-318R, DB-318U
Test Location: Shenzhen SIT Testing Technology Co., Ltd.
Test Specification:
EN 50564:2011
Test Date: December 14, 2015 to December 22, 2015
Test Result:
From the results of our testing on the submitted sample(s), we are of the opinion that the submitted sample(s) are comply with the second stage requirements of (EC) No.278/2009
Tested By: Reviewed By: Approved By:
Tom / Test Engineer Leon Li / Project Engineer Kevin Sun /Manager
Date: 2015-12-30
Date: 2015-12-30
Date: 2015-12-30
Other Aspects: N.A
Abbreviations: ok / P = passed; fail / F = failed; n.a. / N = not applicable The test result in this test report refers exclusively to the presented test sample. This report shall not be reproduced except in full, without the written approval of SIT.
Shenzhen SIT Testing Technology Co.,Ltd. Address: 4th Floor, Co-talent Creative Park, Liuxian Road, Baoan 68 District, Shenzhen Tel:+86-755-29173399 Fax:+86-755-29179933 Email: [email protected] http://www.sit-cert.com Ver.:1.0 / 08.Feb.2011
Shenzhen SIT Testing Technology Co., Ltd. Report No.: SIT151211361U
Page 3 of 12
Ratings:AC/DC ADAPTER: Input: AC100-240V, 0.15A/0.2A, 50/60Hz Output: DC 5V 1000mA DAB/FM radio: DC5V, 1A, 1W, 50/60Hz
TEST INSTRUMENTS
Make/Model Measurement Due of calibration
W310 Power Meter 2016.10.26
IT8512 Electronic Load 2016.10.26
HPA-3110 AC power source 2016.10.26
CONNECTIONS OR MODIFICATIONS TO THE INPUT AND/OR OUTPUT CORD a.c. input type EU plug
Input cord length (mm) N/A
Output cord length (mm) N/A
Output plug type USB Port
Modification to connectors for testing None TEST SETUP Maximum and minimum ambient temperatures (°C)
25.5 (max) 24.7 (min)
Maximum air speed (m/s) 0.1 Test Procedure The tests are carried out in a room that has an air speed close to test sample of < 0.5m/s, and the ambient temperature is maintained at 23±5℃. The test voltages are 230Vac at 50Hz. And 115Vac at 60Hz The test sample was operated at 100% of nameplate current output for at least 30 minutes immediately prior to conducting efficiency measurements. After this warm-up period, if the power level does not drift by more than 5% from the maximum value observed, the EUT can be considered stable and then the measurements were recorded at the end of the 5 minutes period. Subsequent load conditi ons can then be measured under the same 5 minutes stability.
Shenzhen SIT Testing Technology Co., Ltd. Report No.: SIT151211361U
Page 4 of 12
0. General P
0.1
Ambient condition mel requirement of: Ambient temperature (23±5)℃ Airspeed ≤0.5m/s (EN50564 )
Ambient: 24.1℃ Airspeed: 0.1m/s
P
0.2
Power source mets requirement of: Frequency 50Hz ±1% THD value <2% Ratio of peak value of test voltage to rms of 1.33 to 1.49 (EN50564 )
Frequency: 50Hz THD: 0.12% Ratio: 1.41
P
0.3 Power measurement accuracy P
Measurements of power of 0.5W or greater shall be made with an uncertainty of less than or equal to 2% at the 95% confidence level. Measurements of power of less than 0.5W shall be made with an uncertainty of less than or equal to 0.01W at the 95% confidence level. The power measurement instrument shall have a resolution of: - 0.01W or better for power measurements of 10W or less (EN50564)
P
0.4 Test approach used
- Stable mode (EN50564 )
P
- Average power approach (EN50564 )
N/A
- Average energy approach (EN50564 )
N/A
0.5 Test circuit
- Test circuit acc. to Fig.1 is used P
- Other test circuit is used See attachment N/A
Shenzhen SIT Testing Technology Co., Ltd. Report No.: SIT151211361U
Page 5 of 12
Fig.1 Test circuit
1. No-load power consumption P
1.1 Measured power consumption in no-load condition: See attachment table P
1.1.1 Stage 1 limit: ≤0.50W
1..1.2 Stage 2 limit: P
≤0.50W AC-AC external power suppliers except low voltage external power suppliers ,Po ≤51.0W
N/A
≤0.50W AC-AC external power suppliers except low voltage external power suppliers ,Po >51.0W
N/A
≤0.30W AC-DC external power suppliers except low voltage external power suppliers ,Po ≤51.0W
P
≤0.50W AC-DC external power suppliers except low voltage external power suppliers ,Po >51.0W
N/A
≤0.30W Lower voltage external power supplies, Po ≤51.0W
N/A
2. Average active efficiency P
2.1 Measured average active efficiency: P
2.1.1 Stage 1 limit: N/A
≥0.500*Po for Po<1.0W N/A
≥0.090*ln(Po)+0.500 for 1.0W≤Po ≤51.0W N/A
≥0.850 for Po >51.0W N/A
Shenzhen SIT Testing Technology Co., Ltd. Report No.: SIT151211361U
Page 6 of 12
2.12 Stage 2 limit: P
≥0.480*Po+0.140 for AC-AC and AC-DC external power supplies,except low voltage external power supplies, Po≤1.0W
N/A
≥0.063*ln(Po)+0.622 for AC-AC and AC-DC external power supplies,except low voltage external power supplies, 1.0W<Po ≤51.0W
See attachment table P
≥0.870 for AC-AC and AC-DC external power supplies,except low voltage external power supplies, Po>51.0W
N/A
≥0.497*Po+0.067 for Lower voltage external power supplies, Po≤1.0W
N/A
≥0.075*ln(Po)+0.561 for Lower voltage external power supplies, 1.0W<Po ≤51.0W
N/A
≥0.860 for Lower voltage external power supplies, Po>51.0W
N/A
Shenzhen SIT Testing Technology Co., Ltd. Report No.: SIT151211361U
Page 7 of 12
Test results Test results for 115V/60Hz Model: DB-318 ---
No load Active power values
Percent of nameplate current 0% 25% 50% 75% 100% Average
Output current (A) 0.00 0.25 0.50 0.75 1.00 -
Output voltage (V) 5.26 5.24 5.13 5.18 5.10 -
Output power (W) 0.00 1.31 2.56 3.88 5.10 -
a.c. input current (A) 0.150 12.7 25.9 31.5 47.3 -
a.c. input voltage (V) 115.04 115.05 115.01 115.05 115.04 -
a.c. input power (W) 0.124 0.670 1.456 2.134 3.241 -
Total harmonic distortion ( THD) 1.0% 1.2% 1.1% 1.0% 1.1% -
True power factor 0.4750 0.4843 0.4712 0.5121 0.5014 -
Power consumed by EUT (W) 0.118 0.815 1.41 2.07 2.14
Efficiency - 80.23% 80.44% 80.75% 80.39% 80.45%
Test results for 230V/50Hz
---
No load Active power values
Percent of nameplate current 0% 25% 50% 75% 100% Average
Output current (A) 0.00 0.25 0.50 0.75 1.00 -
Output voltage (V) 5.28 5.21 5.23 5.17 5.13 -
Output power (W) 0.00 1.30 2.62 3.87 5.13 -
a.c. input current (A) 0.212 21.3 47.7 57.4 66.7 -
a.c. input voltage (V) 230.08 230.05 230.09 230.08 230.04 -
a.c. input power (W) 0.074 1.212 3.174 4.352 5.378 -
Total harmonic distortion ( THD) 1.1% 1.1% 1.0% 1.2% 1.1% -
True power factor 0.4782 0.4987 0.4573 0.4127 0.5012 -
Power consumed by EUT (W) 0.212 1.12 2.64 3.42 4.12
Efficiency - 80.42% 80.74% 81.12% 81.47% 80.94%
Model: DB-318
Shenzhen SIT Testing Technology Co., Ltd. Report No.: SIT151211361U
Page 8 of 12
Summary of test results According to the ecodesign requirements stated in Annex I, the limits of the no-load condition power consumption and the average active efficiency of the Unit Under Test (UUT) are varied based on its nameplate output power (P o). The limits are defined at two stages, the verdict of this test report is assessed based on the limit of the second stage. The no-load condition power consumption shall not exceed the following limits:
/
AC-AC external power supplies, except low voltage external power supplies
AC-DC external power supplies, except low voltage external power supplies
Low voltage external power supplies
Po ≤ 51.0 W 0.5 W 0.3 W 0.3W
Po > 51.0 W 0.5 W 0.5 W N/A
The no-load condition power consumption shall not exceed 0.50W
0.05 W pass
The average active efficiency shall be not less than the following limits:
/ AC-AC and AC-DC external power supplies, except low voltage external power supplies
Low voltage external power supplies
Po ≤ 1.0W 0.480 * Po + 0.140 0.497 * Po + 0.067
1W<Po ≤ 51.0 W 0.063 * ln (Po) + 0.622 0.075 * ln (Po) + 0.561
Po > 51.0 W 0.870 0.860
The test results comply with the second stage requirement s of (EC) No.278/2009
Shenzhen SIT Testing Technology Co., Ltd. Report No.: SIT151211361U
Page 9 of 12
PHOTOGRAPHS OF EUT
Appearance photograph of EUT
Appearance photograph of EUT
Shenzhen SIT Testing Technology Co., Ltd. Report No.: SIT151211361U
Page 10 of 12
Appearance photograph of EUT
Appearance photograph of EUT
Shenzhen SIT Testing Technology Co., Ltd. Report No.: SIT151211361U
Page 11 of 12
Appearance photograph of EUT
Appearance photograph of EUT
Shenzhen SIT Testing Technology Co., Ltd. Report No.: SIT151211361U
Page 12 of 12
Appearance photograph of EUT
Appearance photograph of EUT
***End of the report***