simple care -. afalver. guidelines your easy2grow 80 mim …

AQU-._Afalver. ,

Pllow your

P‘OntS to

,e%S Worte tuming your

system on.

AQUA JYeTM mim

iglow your

langto este:0e

beiere turning your

system on.

Your easy2grow 80 set-up guidelines

[email protected] I www.autopot.co.uk I +44 (0)844 8581520

80

Trays & Pots available in

green or black


Ensuring that the AQUAvalve floods and drains correctly

Care and maintenance

Making sure your AQUAvalve floods and drains correctly is simply achieved and only takes a few seconds.

Hold the AQUAvalve at eye level so that you can see the yellow silicon fitted to the top float resting on the hole below it.

The yellow silicon must create a tight seal when touching the hole.

If it looks like it is not sitting parallel on the hole below, simply lift the top float and apply pressure to one side of the yellow silicon, drop the float and hold at eye level again. Repeat the procedure if necessary.

At the end of your growing season, clean the AQUAvalve using warm soapy water. Using an old tooth brush will help.

The AQUAvalve is easily disassembled. The top float will slide all the way across and the bottom float is unclipped from its pivoting position. The circular discs fitted to the top float can also be removed by using pliers to grip the raised point.

At this point is it advisable to remove the yellow silicones to avoid them being lost.

It is also handy to have a paper clip or pipe cleaner to hand so that you can push it through the AQUAvalve nozzle, this will remove any lime scale build up that may have occurred during the growing season.

Blowing through the AQUAvalve nozzle will also help to remove any build up. Do not under any circumstances use a drill & drill bit to clear the AQUAvalve nozzle.

This will potentially damage the AQUAvalve beyond repair.

Simple careguidelines

11

2

2

3

4

Ensure the yellow silicon is sitting parallel on the hole below it. Hold at eye level

to check the position is correct

plantsAllow your

to establish

before turning your

system on.

*X* es•

00 es•

ÖD OD

aoe 00

00

00 es•

es• aoe Sao

al Zoo

00

Sao

ÖD

es• 00 es• 00 *.X.* es• oa oa

00 00

4

es• ooe ooe es• oae oa *X*

e eXo L3Xs. es• ol Zoo

ooe Zoo 00 e*:

4

ee 00 es• 00 om 00 e*:

es• eXe ooe *X* es• :eXE e*:

eXe 3XE• es• ooe oae e*:

*X* 3XE• *X* E 3XO e*:

ÖDs• ÖDs• ÖD ÖD ÖDs• ÖO e*:

immemisa

soles sp• toic 040

BP

gej oa öö

00 00

Xe X*

oae eXE oae oae

n

1

00000000%%0,

1

•+, spe eigor (4»

Xe eXe

00 00 *e

oae ÖO eOD Xe

00 mär «E•

OD X* ge•

ma 00 *X*

OD OD X*

OD 3XE OD

eOD XE eOD XE eOD XE

X* oae ao

OD OD 3XE

Xe X* 11 eXe X* Xe

00 öö

eXe «e ei> ee

4

4

-4

-4

E

oae *Xo E

X*

3XE OD eXE

OD 3XE

0000 %%&

«s• eXe

00 400 00

«E• 00 eXe

ee: oae

OD X* «s•

«s• eXe eoa Zoo

easy2grow module setup

instructions

If you require any guidance email - [email protected]

1

6

8

2

Put black marix discs in pots

Fill pots with medium and pot up plants.

Water through pots and allow to drain outside the tray.

5

Position tray so it is level

Insert root control disc Gold face up

Place both pots in tray, make sure they are CLEAN!

Place lid over valve onto tray

Allow your plants to establish for 7-10 days before turning system on

Connect AQUAvalve so ‘half moon’ is on T section in the tray

4

Plan views and options

Suggested layout


• 1x750ltrFlexiTankorrigid green 750 ltr tank

• 1x16mmclick-fittank adaptor&filter

• 1x20metresof16mmpipe• 4x16mmin-linetap• 3x16mmteeconnectors

• 20x16mm-6mmcrossconnector• 40x2Pottray&lid• 80x8.5ltrpots• 40xAQUAvalve• 1x20metresof6mmpipe• 80xmarixdisc• 80xrootcontroldisc

750 ltrFlexiTank

6mm pipe

16mm pipe

16 - 6mm cross connector

16mm tee connector

16mm inline tap

AQUAvalve

16mmclick-fit tankadaptor&filter

Advice

575mm

275m

m

750 ltrtank

900mm

1200

mm

7

According to the size of your system connect your 6mm/16mm pipe to relevant fitting or tank...

Using your front instruction sheet, repeat the module set up instructions for the number of trays.

Cut 6mm/16mm pipe to appropriate length

3Remove collar

Push 6mm pipe through collar and attach to AQUAvalve nozzle

Rescrew collar - DON’T overturn... when you feel it grip STOP

easy2grow dimensions

• Potupyourplants,waterthrough,thenallowyourplantstoestablishinthepotsforaperiodof7to10days before turning your system on. This will encourage a stronger and healthier root system.

• Alwaysraiseyourtanktoaminimumof150mmabovethehighestAQUAvalveandre-fillthetankwhenthereisapproximatelya1/3ofthesolutionleft-NEVERALLOWTHETANKTORUNEMPTY.

• Forbestresults,werecommendmineralfertilisers.Donotuseorganicfertilisers,astheyhaveatendencyto block small pipe work.

• Cleanallsubstratefromthebottomandsidesofthepotsbeforeplacingineachtray. This will ensure your system is clean from the start.

• Alwaysusefreedrainingsubstrates,forexample:soil/perlite,coco/perlite,soil/claypebbles, coco/claypebbles,rockwool/claypebbles.

easy2grow 80 contents

Deutschland: https://www.growland.net

Europe: https://www.growland.biz

France: https://www.growland.fr

España: https://www.growland.es

Österreich: https://www.growland.at

Nederland: https://www.growland.nl

Italia: https://www.growland.it

United Kingdom: https://www.growland.co.uk

simple care -. afalver. guidelines your easy2grow 80 mim …

Documents