sidho-kanho-birsha universityskbu.ac.in/cvs/notice/20170608154509.pdfsidho-kanho-birsha university...

of 17

Sidho-Kanho-Birsha University Ranchi Road, P.O.- Sainik School

District - Purulia, PIN – 723104, W.B.

Phone : 03252- 202419 Website-www.skbu.ac.in

Ref No: FO/ 325 /SKBU/17 Date: 01/06/2017

E- Tender Notice

E- Tender are invited from reputed vendor or suppliers to supply the following office

furniture. Intending bidder may download the tender documents from the website

www.skbu.ac.in/www.wbtenders.gov.in. Only online tender documents will be

accepted. Last date of submission 22/06/2017 up to 2:00 PM, Date of Opening

24/06/2017 at 3 PM .

Terms & Condition:-

1. SKB University reserves the right to reject any or all tenders without assigning any

reason whatsoever.

2. No advance payment or payment against Performa invoice will be made. Payment

will be made after receipt, inspection, and installation/testing.

3. All damaged or unapproved goods shall be returned at the bidder’s risk and cost and

the incidental expenditure thereupon shall be recovered from the concerned party.

4. On acceptance of tender, the date of delivery should be strictly adhered to otherwise,

the SKB University reserves the right not to accept the delivery in full or in part. In case

the order is not executed within the stipulated period, the SKB University will be at

liberty to make purchases through other sources.

5. Payment of bill will be made through by crossed account payee Cheque or electronic

payment (NEFT) only after delivery and successful installation of each of the items.

6. Delivery Schedule: The Company shall be able to deliver the required items within

15 days of the receipt of order. Delivery/Installation is to be done at Purulia, West

Bengal.

7. Liquidated Damages : The Company shall be liable to indemnify the SKB University

in all respects and meet and pay off the litigation expenses and all the liabilities including

damages, sums etc. arising out of and as a consequence of the negligence, deficiencies,

mistakes, lapses, delays etc. in the execution of the various jobs and the services

provided.

8. Purchase Order: The purchase order for the entire quantity can be placed either in

one lump sum or as per the requirement through repeat order subject to availability of

http://www.skbu.ac.in/

of 17

fund of the required items. The quantity shown is tentative and may increase or

decrease.

Annexure 1

Proforma For Techncial Bid

SL Particulars Information

1 Name of the Firm & Owner : (with Telephone/Mobile Numbers, email)

2 Type of Organisation (Proprietorship/Partnership/Pvt. Ltd./Limited Company) Month/Year of Establishment

3 Website of Bidder, if any

4 Month/Year of Establishment

5 PAN/Sales Tax/VAT Regd. Nos.

6 Annual Turnover 2016-17

7 Whether product(s) offered by the bidders are exactly as per the configuration of SKB University. If not, indicate the changes in each product

8 Clientele (submit copies)

9 Validity of Tender

10 Whether Terms & Conditions issued by SKB University are acceptable to the Firm

11 Whether Warranty as per the desired specification

** Bidder should only quote rate for 1 unit of each item in BOQ. Date Name: Signature of Owner/Authorized Representative Designation:

of 17

Technical Specification Sl No Model Name Specifications UNIT

1

7 LEVER

ROUND

PADLOCK

Supply and placement with following specification 7 Lever round padlock

.Manufacturer should be a certified member of BIFMA for the last 10 years ,

SEFA-8 and should be following management systems as per ISO 9001:2015,

ISO 14001:2004, OHSAS 18001:2007 and energy management system as per

ISO 50001:2011 in accordance with the TÜV NORD CERT auditing and

certification procedures for Design, Development, Manufacturing, Marketing,

Sales, Supply and Servicing of Home & Institutional, Interiors, Furniture,

Accessories & Related Products and Provide Solutions for Home & Work Space

and should have Green Guard Certification for few of its products also should

have the service set up at least at district headquarter.

NOS

2

Aquaguard

Water Cooler

Cum Purifier

(AGCCP)

Supply and placement with following specification Aqua guard cooler cum

purifier Technical SpecificationsDimension:(H x D x W):700x430x460 mmRated

Voltage: 230 Volts, 50 Hz, ACWorking Voltage Range:180-260 VoltsPower

Rating: 550 Watts ± 10 % VCurrent Rating: 3 Amps MaxUV. Lamp Wattage: 8

WattsRated Compressor Capacty:910Kcal/hr±5%Water Cooling Capacity: 40

LPHWater Flow rates:0.666LPMWater Pressure:0.4 kg/cm²(Min.)Water

Pressure: 2.0kg/cm² (Max.)Max. Temp drop under standard test condition: 16.5°C

NOS

3 CHAIR FU 1007

Supply and placement with following specifications Overall Size : Depth - 59.5

cmWidth - 54.0 cm Height - 82.5 cm Seat Height- 46.0 cm Seat/ Back Assembly:

The seat and back are made from 1.0+/-0.1 cm. thick hot pressed moisture

resistant, commercial plywood measured as per QA method and upholstered with

PU foam and febric.Manufacturer should be a certified member of BIFMA for the

last 10 years , SEFA-8 and should be following managment systems as per ISO

9001:2015, ISO 14001:2004, OHSAS 18001:2007 and energy management

system as per ISO 50001:2011 in accordance with the TÜV NORD CERT

auditing and certification procedures for Design, Development, Manufacturing,

Marketing, Sales, Supply and Servicing of Home & Institutional, Interiors,

Furniture, Accessories & Related Products and Provide Solutions for Home &

Work Space and should have Green Guard Certification for few of its products

also should have the service set up at least at district headquarter.

NOS

4 CHAIR FU 7046

Supply and placement with following specifications Revolving chair The seat

made from 1.2cm. thk. hot pressed plywood and back is injection moulded from

black Co-polymer Polypropylene upholstered with fabric and moulded

Polyurethane foam together with seat and back covers. The back foam is designed

with contoured lumbar support for extra comfort. SEAT SIZE: 45.0cm(W) x

42.0cm.(D) BACK SIZE: 40.0cm(W) x 47.0cm.(H). The seat and back covers are

injection moulded in black Co-polymer Polypropylene. The polyurethane foam is

moulded with density = 45 +/-2 kg/m3 and Hardness = 20 +/- 2 on Hampden

machine at 25% compression. The one-piece armrests are injection moulded from

black Nylon. The armrests are fitted to the seat with armrest connecting brackets

made of 0.5cm. thk. HR steel. Should have Permanent contact mechanism

designed with the features such as 360° revolving type, 14° maximum back-tilt

only, Upright position locking and Tilt tension adjustment. The pneumatic height

adjustment has an adjustment stroke of 9.0 cm. The bellow is 3 piece telescopic

type and injection moulded in black Polypropylene. The pedestal is injection

moulded in black 30% glass-filled Nylon and fitted with 5 nos. twin wheel castors

(castor wheel dia. 5.0cm.). The edestal is 57.0 cm. pitch-centre dia. (67.0 cm with

castors). The twin wheel castors are injection moulded in Black

Nylon.Manufacturer should be a certified member of BIFMA for the last 10 years

, SEFA-8 and should be following managment systems as per ISO 9001:2015,

ISO 14001:2004, OHSAS 18001:2007 and energy management system as per

ISO 50001:2011 in accordance with the TÜV NORD CERT auditing and

certification procedures for Design, Development, Manufacturing, Marketing,

Sales, Supply and Servicing of Home & Institutional, Interiors, Furniture,

Accessories & Related Products and Provide Solutions for Home & Work Space

and should have Green Guard Certification for few of its products also should

have the service set up at least at district headquarter.

NOS

of 17

5 T-32

Supply of table of size 1199Wx590Dx750H with one drawer of size

355.5Wx559Dx167H having top made of prelaminated particle board of 18+/-

5mm thick with 2mm thick PVC edge banding on all sides and metal

understructure made of C frame made from 0.9+/-0.09mm thick powder coated

50 microns (+/-10) CRCA MS, tubular frame of dimesions 25.4+/-0.3mmX1.2+/-

0.096 mm thick MS ERW tube. The drawer should have 10 lever cam lock and

0.5+/-0.07mm thick CRCA MS shell and drawer tray and 0.8+/-0.1mm thick

CRCA MS drawer front and plastic handles. Manufacturer should be having

certifications like; BIFMA, ISO 9001:2008, ISO 14001:2004, ISO 18001:2007

and should have Green Guard Certification for few of its products. and should

have the service set up at least at district headquarter

NOS

6

UNWIND CHAIR

WITH SS

FRAME

Supply and placement with following specifications with arm rest seat and back

and armrest are made up of injction moulded high impact strength polypropelene

polymer compound with indoor grade UV resistance. Overall size of the chair

should be 52.5cm width, 55.8cm depth, 84.5cm height and 45cm seat height. The

chair should be having MS powder coated welded tubular frame made of 2.22+/-

0.03cm X0.16+/-0.0128cm and 3.5+/-0.03cm x1.5+/-0.03X1.6+/-0.0128cm

MSRW tube, powder coated to DFT 50+/- 10 microns. The frame should be

provided with shoes made of high impact strength polypropelene polymer

compound with indoor grade UV resistance and should be press fiitted with

tubular frame.Manufacturer should be a certified member of BIFMA for the last

10 years , SEFA-8 and should be following managment systems as per ISO








NOS

7 FU L 43

Supply and placement with following specifications The premium lounge seating

system standing on beam with side frame assemblies . SIDE FRAME

ASSAMBLY : The side frame assembley is fitted to the two ends of the conecting

beam assembly to from the leg -cum armrest assembly . It is made of 3.81+-

0.3cm X0.2 +- 0.016 cm MS E.R.W tube and powder . the ends are fitted with

ABS moulded end caps. TIE MEMBER :- It is the connecting beam assy which

holds the two side frames each others 2 nos tie members are used to connect the

side frames . The tie members is made of 3.81+- 0.03 cm X 0.2 +- 0.016 cm .

thick MS E.R.W. tube and powder coated the seat/ back assemblies are mounted

on of the tie member which has 5.0+-0.1cm X0.5+-0.1cmthk long MS Std angels

welded to mount the seat and back. SEATREST ASSEMBLIY:- The seat rest

assembly consist of a fabricatted inner frame assembly insitu moulded high

resilience (HR) polyurethane foam having density =45+/- 2kg/m3 with hardness

load 25 +- kgf as per IS :7888 FOR 25% COMPRESSION OF THE FOAM . the

complete moulded seat rest assembly is covered with replaceble fabric uphlstry

cover. BACKREST ASSEMBLY:- The back rest assembly is flexing type and

consists of a fabricated inner frame assembly insitu -moulded with High

Resilience(HR)polyurethane foam having density = 45+/- 2 kg/m3 with hardness

load 14+- 2 kgf as per IS 7888 for 25% COMPRESSION OF THE FOAM . THE

COMPLETE MOULDED BACKREST ASSEMBLY IS COVERED WITH A

REPLACEBLE FABRIC UPHOLSTRY COVER..Manufacturer should be a

certified member of BIFMA for the last 10 years , SEFA-8 and should be

following managment systems as per ISO 9001:2015, ISO 14001:2004, OHSAS

18001:2007 and energy management system as per ISO 50001:2011 in

accordance with the TÜV NORD CERT auditing and certification procedures for

Design, Development, Manufacturing, Marketing, Sales, Supply and Servicing of

Home & Institutional, Interiors, Furniture, Accessories & Related Products and

Provide Solutions for Home & Work Space and should have Green Guard

Certification for few of its products also should have the service set up at least at

district headquarter.

NOS

of 17

8 CHAIR FU 7212

Supply and placement with following specifications chair FU 7212 seat and back

made up of 1.2+/-0.1 cm thick hot pressed plywood, upholstered with fabric and

moulded Polyurethane foam with PVC lipping all around. The back foam should

be designed with contoured lumbar support for extra comfort. BACK SIZE:

49.5cm.(W) x 45.5cm.(H) SEAT SIZE: 49.5cm.(W) x 43.0cm.(D). The

polyurethane foam is moulded with density = 45 +/-2 kg/m3 and Hardness = 20

+/- 2 on Hampden machine at 25% compression. The one piece armrest should be

made of black integral skin polyurethane with 50-70 shore hardness and

reinforced with MS insert. The armrests are scratch and weather resistant and

should be fitted to the seat with seat armrest connecting bracket made of 0.3+/-

0.022cm thick HR steel. The understructure should be a tubular frame of

cantilever type made of 2.54+/-0.03cm x0.2+/-0.16 cm thick MS ERW tube and

black powder coated. Manufacturer should be a certified member of BIFMA for

the last 10 years , SEFA-8 and should be following managment systems as per

ISO 9001:2015, ISO 14001:2004, OHSAS 18001:2007 and energy management







NOS

9 FU 7201

Supply and placement with following specifications SEAT/BACK ASSEMBLY: The seat and back are made up of 1.2 ±0..1 cm. thick hot pressed plywood measured as per QA method described in OCP-QLTA-P14-18 and upholstered with fabric and moulded Polyurethane foam with PVC lipping all around. The back foam is designed with contoured lumbar support for extra comfort. * PCH-7201 (HIGH BACK) SIZE: 49.5cm. (W) X 69.5cm. (H) * 2. HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density =45+1-2 kg/m3 and hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. 3. ARMRESTS: The one-piece armrests made of black integral skin polyurethane with 50-70 Shore Hardness and reinforced with M.S. insert. The armrests acre scratch and weather resistant. The armrests are fitted to the seat with seat armrest connecting bracket made of 0.3 ±0.022cm. thk. HR steel. 4. CENTRE PIVOT MECHANISM : The center pivot mechanism is designed with the following features: • 360° revolving type. • 17° ±2°maximum tilt on pivot at cerntre. • Tilt tension adjustment. • Upright position locking. 5. PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 12.0 ±0.3cm. 6. TELESCOPIC BELLOW ASSEMBLY: The bellow is 3 piece telescopic type and injection moulded in black Polypropylene. 7. PEDESTAL ASSEMBLY: The pedestal is injection moulded in black 33% glass-filled Nylon-66 and fitted with 5 nos. twin wheel. castors. The pedestal is 66.3 ±0.5cm.(76.3 ±1.0 cm with castors8. TWIN WHEEL CASTORS: The twin wheel castors are injection moulded in Black Nylon. Manufacturer should be a certified member of BIFMA for the last 10 years , SEFA-8 and should be following managment systems as per ISO 9001:2015, ISO 14001:2004, OHSAS 18001:2007 and energy management system as per ISO 50001:2011 in accordance with the TÜV NORD CERT auditing and certification procedures for Design, Development, Manufacturing, Marketing, Sales, Supply and Servicing of Home & Institutional, Interiors, Furniture, Accessories & Related Products and Provide Solutions for Home & Work Space and should have Green Guard Certification for few of its products also should have the service set up at least at district headquarter.

NOS

of 17

10 ENTERPRISE

1500 TABLE

Supply and placement with following specifications TABLE ENTERPRISE

1500 table of size 1500 Wx 750D x 728H. Workspace Should be made of Pre

Laminated Particle Board (PLB) All work surface edges are duly sealed with

2mm thick PVC Edgebanding.Rectangular frameshould be Fabricated

component in 1.2mm thick CRCA (IS:513), Finish: Powder coat (Epoxy

polyester)LegFabricated component in 38mmx25mmx1.2mm thick MS ERW

Tube (IS:7138), Finish: Powder coat (Epoxy polyester). Manufacturer should be a










NOS

11

TIME OUT 8

SEATER PU

COATED

Supply and placement with following specifications Overall Size : Depth –

2329.0 mm Width - 1175.0 mm Height – 750.0 mm Work Surface, PU Painted 25

mm Thick (+/- 1mm), Base Material- 25 mm MDF board. On top PU Painted of

minimum 2H hardness with 75% gloss as per color chart, combination color

graphics on the centre. Color as per color chart brown laminate on bottom.

Specially profiled edge for comfort. Understructure, bend pipe understructure of

MS powder coated. Pipe Dia. 38mm, 2mm thick. Understructure fitted with top

by MS machine screws.Legs, MS powder coated legs for PU top. 38 mm Dia.

Pipe legs are fixed with understructure and table top. Glide, Plastic glide fixed at

the understructure to prevent the damages of table top during stacking.

Manufacturer should be a certified member of BIFMA for the last 10 years ,

SEFA-8 and should be following managment systems as per ISO 9001:2015, ISO

14001:2004, OHSAS 18001:2007 and energy management system as per ISO

50001:2011 in accordance with the TÜV NORD CERT auditing and certification

procedures for Design, Development, Manufacturing, Marketing, Sales, Supply

and Servicing of Home & Institutional, Interiors, Furniture, Accessories &

Related Products and Provide Solutions for Home & Work Space and should have

Green Guard Certification for few of its products also should have the service set

up at least at district headquarter.

NOS

12 NANO PERCH 3

STR CHAIR

Supply and placement with following specifications Nano Perch 3 seater

perforated chair Size: (163X57X67.5X40) cm with two arms & without cushion.

Cross Beam: It is made of black powder coated rectangular M.S. ERW Tube

having 8.0 +/- 0.03 cm x 4.0 +/- 0.03 cm x 0.2 +/- 0.014 cm size. leg & Armrestit

is chrome plated made of cold rolled steel with 0.12 +/- 0.013 cm thickness.

Seat/Back Shell: it is powder coated perforated shell made from cold rolled M.S.

sheet (DIN1623 Part1 ST-12 Grade) 0.14 +/- 0.013 cm thickness. The side bar is

made of chrome plated solid steel 3.0 +/- 0.03 cm x 1.2 +/- 0.3 cm with fluting

and plastic inserts. The shell is assembled on the cross beam with help of M8

bolts (per Seat- 8 nos, seat to bracket and 4 nos Bracket to cross Beam).

Manufacturer should be a certified member of BIFMA for the last 10 years ,

SEFA-8 and should be following managment systems as per ISO 9001:2015, ISO

14001:2004, OHSAS 18001:2007 and energy management system as per ISO

50001:2011 in accordance with the TÜV NORD CERT auditing and certification

procedures for Design, Development, Manufacturing, Marketing, Sales, Supply

and Servicing of Home & Institutional, Interiors, Furniture, Accessories &

Related Products and Provide Solutions for Home & Work Space and should have

Green Guard Certification for few of its products also should have the service set

up at least at district headquarter.

NOS

of 17

13 FINNESSE 4020

TABLE

Supply and placement with following specifications OF SIZE 1200X600X740

HAVING TOP AND SIDE PANELS MADE OF 25 MM THICK PLAIN

PARTICLE BOARD (PPB) CLAD WITH 0.6MM THICK POST FORMED

LAMINATE AND 1MM THICK BACKING LAMINATE (BDL)FLAT EDGE

DULY SEALED WITH 2MM THICK PVC BEADING AND HAVING

MODESTY PANEL IN FRONT MADE OF 18MM THICK PLAIN PARTICLE

BOARD (PPB) CLAD WITH 1.0MM THICK DECORATIVE LAMINATE

(DL) ON BOTH SIDES. EDGE SEALED WITH 2MM THICK PVC

BEADING. Manufacturer should be a certified member of BIFMA for the last 10

years , SEFA-8 and should be following managment systems as per ISO








NOS

14 T-9

Supply and placement of Godrej make or equivalent as per design approve as per order Table of Size:- (1365 X 680 X 735) mm UNITISED OFFICE TABLES COLOUR SCHEME : COLOUR CODE TOP + UPPING STORAGE UNIT + HANDLES TOP FRAME + LEGS 05 Grey Shell : TA Grey Handle : Brown Drawers : TA Grey Char Brown 26 Ivory Shell : Char Brown Handle : Brown Drawers : Beige Char Brown 47 Rosewood Shell : her Brown Handle : Brown Drawers : Beige Char Brown 54 Teak Shell : Char Brown Handle : Brown Drawers : Beige Char Brown 55 Rosewood Shell : Olive Handle : Brown Drawers : Olive Char Brown 59 Bay Beech Shell : Black Handle : Brown Drawers.The Panels are made from 18 ± 0.5 mm thk Pre—laminated Boards as per with 2mm thick PVC Edge banding on all sides. *T-104 = 25 ± 0.5 mm Thick Pre—Laminated Board. Understructure: C-Frame Tubular Frame For T9 :Dia 25.4±0.3mm x 1.2±0.096mm Thk MS ERW tube. For others :Sq. 25.4±0.3mm x 1.2±0.096mm Thk MS ERW tube. Made from 1.0 ±0.09mm thk powder coated 50microns (±10) CRCA MS. Storage Shell : 0.5 ± 0.07 mm Thk CRCA MS. Drawer Tray : 0.5 ± 0.07 mm Thk CRCA MS. Drawer Front: 0.8 ± 0.1: mm Thk CRCA MS. Lock : 10 Lever Cam. Lock CONTP,r.v, CAP.. Handles : Built in Plastic. Manufacturer should be a certified member of BIFMA and should be following managment systems as per ISO 9001:2008, ISO 14001:2004, ISO 18001:2007 and energy management system as per ISO 50001:2011 in accordance with the TÜV NORD CERT auditing and certification procedures for Design, Development, Manufacturing, Marketing, Sales, Supply and Servicing of Home & Institutional, Interiors, Furniture, Accessories & Related Products and Provide Solutions for Home & Work Space and should have Green Guard Certification for few of its products also should have the service set up at least at district headquarter.

NOS

of 17

15

ANTI

VIABRATION

TABLE 600 D &

750 H

Supply and placement of as per design approve as per order Product size: back size 40 cm W X45 cm seat size 43 cm X 39 cm. The seat and back are made up of 1.2 cm thick hot pressed plywood upholstred with fabric and moulded polyurethane foam with PVC lipping allaround. The back foam is designed with contoured lumber support for extra comfort. High resilience (HR) polyurethane foam : The HR polyurethane foam is moulded with density =45=+/-2 kg/m3 and hardness load 16 +-2 kgf as per IS 7888 for 25%compression. Armrest The one piece armrests are injection moulded foam black co- polymer polypropylene. the armrest are fitted to the seat with armrest connecting brackets made of 0.5 cm thk HR steel. Permanent contact mechanism : The permanent contact mechanism is designed with the following features 360 degree revolving type 14 degree maximum back tilt only upright position locking tilt tension adjustment. Pneumatic height adjustment: The Pneumatic height adjustment has an adjustment stroke of 12 cm. Telescopic bellow assembly :- The bellow is 3 piece telescpic type and injuction moulded in black polypropylene. Pedestal assembly: The pedestal is injuction moulded in black 30% glass fitted nylon and fitted with 5 nos twin wheel castors. The pedestal is 61.0 cm pitch-center dia. (71.0cm with castors). twin wheel castors:- The twin castors are injection moulded in black nylon.Manufacturer should be a certified member of BIFMA, SEFA-8 and should be following management systems as per ISO 9001:2015, ISO 14001:2004, OHSAS 18001:2007 and energy management system as per ISO 50001:2011 in accordance with the TÜV NORD CERT auditing and certification procedures for Design, Development, Manufacturing, Marketing, Sales, Supply and Servicing of Home & Institutional, Interiors, Furniture, Accessories & Related Products and Provide Solutions for Home & Work Space and should have Green Guard Certification for few of its products also should have the service set up at least at district headquarter.

NOS

16

ANTI

VIABRATION

TABLE 900 D &

750 H

Supply and placement of as per design approve as per order Product size for antivibration table width 600 mm Depth 600 mm height 750 mm Tubular frame - Completely modular type tubular frame, which carries the load of kadappa and granite, kept on it. High-tension Pan head M6 Zinc black-coated screws (for better corrosion resistance) are used for the fastening. The material used is: 40Sq x 1.6 mm thick ERW tube and the overall load carrying capacity of tubular frame is 250 kgs of uniform distributed load. Cover Panels – They are 0.8 mm thick CRCA MS sheet and pre-treated and epoxy powder coated for better corrosion resistance. The thickness of powder coat is 45-50 microns which passes the test of Salt Spray for 1000 Hours and having the Scratch Hardness of 3 Kgs. Kadappa - 25mm thick Kadappa acts as the shock-dampening component. Work Surface – granite Vibration Isolating Rubber pads - The objective of using these rubber pads is to absorb the pulsating vibrations coming from the floor .The pads are made up from combination of nitrite rubber, cork particles and cross linked polyester fiber. This high-grade compound material possesses all the physical and mechanical properties required to minimize the dampening effect. Levelling screws - The Tubular frame has the provision for 4 height adjusters or Levelling Screws that take care of all levelling aspects. Manufacturer should be a certified member of BIFMA, SEFA-8 and should be following management systems as per ISO 9001:2015, ISO 14001:2004, OHSAS 18001:2007 and energy management system as per ISO 50001:2011 in accordance with the TÜV NORD CERT auditing and certification procedures for Design, Development, Manufacturing,

NOS

of 17

Marketing, Sales, Supply and Servicing of Home & Institutional, Interiors, Furniture, Accessories & Related Products and Provide Solutions for Home & Work Space and should have Green Guard Certification for few of its products also should have the service set up at least at district headquarter.

17

ANTI

VIABRATION

TABLE 900 D &

900 H

Supply and placement of as per design approve as per order Product size for antivibration table width 900 mm Depth 600 mm height 750 mm Tubular frame - Completely modular type tubular frame, which carries the load of kadappa and granite, kept on it. High-tension Pan head M6 Zinc black-coated screws (for better corrosion resistance) are used for the fastening. The material used is: 40Sq x 1.6 mm thick ERW tube and the overall load carrying capacity of tubular frame is 250 kgs of uniform distributed load. Cover Panels – They are 0.8 mm thick CRCA MS sheet and pre-treated and epoxy powder coated for better corrosion resistance. The thickness of powder coat is 45-50 microns which passes the test of Salt Spray for 1000 Hours and having the Scratch Hardness of 3 Kgs. Kadappa - 25mm thick Kadappa acts as the shock-dampening component. Work Surface – granite Vibration Isolating Rubber pads - The objective of using these rubber pads is to absorb the pulsating vibrations coming from the floor .The pads are made up from combination of nitrite rubber, cork particles and cross linked polyester fiber. This high-grade compound material possesses all the physical and mechanical properties required to minimize the dampening effect. Levelling screws - The Tubular frame has the provision for 4 height adjusters or Levelling Screws that take care of all levelling aspects. Manufacturer should be a certified member of BIFMA, SEFA-8 and should be following management systems as per ISO 9001:2015, ISO 14001:2004, OHSAS 18001:2007 and energy management system as per ISO 50001:2011 in accordance with the TÜV NORD CERT auditing and certification procedures for Design, Development, Manufacturing, Marketing, Sales, Supply and Servicing of Home & Institutional, Interiors, Furniture, Accessories & Related Products and Provide Solutions for Home & Work Space and should have Green Guard Certification for few of its products also should have the service set up at least at district headquarter.

NOS

of 17

18

ANTI

VIABRATION

TABLE 900 D &

750 H

Supply and placement of Godrej make or equivalent as per design approve as per order Product size for antivibration table width 900 mm Depth 600 mm height 750 mm Tubular frame - Completely modular type tubular frame, which carries the load of kadappa and granite, kept on it. High-tension Pan head M6 Zinc black-coated screws (for better corrosion resistance) are used for the fastening. The material used is: 40Sq x 1.6 mm thick ERW tube and the overall load carrying capacity of tubular frame is 250 kgs of uniform distributed load. Cover Panels – They are 0.8 mm thick CRCA MS sheet and pre-treated and epoxy powder coated for better corrosion resistance. The thickness of powder coat is 45-50 microns which passes the test of Salt Spray for 1000 Hours and having the Scratch Hardness of 3 Kgs. Kadappa - 25mm thick Kadappa acts as the shock-dampening component. Work Surface – granite Vibration Isolating Rubber pads - The objective of using these rubber pads is to absorb the pulsating vibrations coming from the floor .The pads are made up from combination of nitrite rubber, cork particles and cross linked polyester fiber. This high-grade compound material possesses all the physical and mechanical properties required to minimize the dampening effect. Levelling screws - The Tubular frame has the provision for 4 height adjusters or Levelling Screws that take care of all levelling aspects. Manufacturer should be a certified member of BIFMA, SEFA-8 and should be following management systems as per ISO 9001:2015, ISO 14001:2004, OHSAS 18001:2007 and energy management system as per ISO 50001:2011 in accordance with the TÜV NORD CERT auditing and certification procedures for Design, Development, Manufacturing, Marketing, Sales, Supply and Servicing of Home & Institutional, Interiors, Furniture, Accessories & Related Products and Provide Solutions for Home & Work Space and should have Green Guard Certification for few of its products also should have the service set up at least at district headquarter.

NOS

of 17

19 FU L 53 MIDAS

3 SEATER SOFA

Supply and placement with following specifications The Midas sofa is a lounge seating system standing on beam with side frame assemblies. It is available in three different models: 3-seater, 1. LH/RH SIDE FRAME: The LH/RH side frame is fitted to the two ends of the seat/back mounting frame to form the leg assembly. It is made of SS J4 Grade tube 0 4.44 cm. x 1.5mm thk. 2. SEAT/BACK MOUNTING FRAME: The seat/back mounting frame assy. holds the two side frames together. The mounting frames, 2nos are used to connect the side frames. The mounting frame is made of MS. E.R.W. tube 05.08±0.03cm. x 3.15±0.0252cm thk. black painted. The seat/back is mounted on 4.0±0.03cm x 2.0±0.02cm x 0.2±0.016cm thk M.S. rectangular tube which is welded on the beam of seat/back mounting frame. 3. SEAT/BACK ASSEMBLY: The seat/back assembly consists of 1.2±0.1cm thk plywood insert with Polyurethane foam having density = 45 +1- 2 Kg/m3 and hardness of the P. U. foam = 18 to 22 kg on Hampden m/c for 25% compression of the foam. The complete moulded seat/back assembly is covered with a replaceable fabric upholstery cover. *SEAT/BACK SIZE: 54.5 cm. (W)-x- 46.7cm. (D) x 12.5cm. (T) 4. BOTTOM SHOES: The side frames are fitted with front and rear bottom shoes made of injection moulded polypropylene. 5. FABRIC (VELVETINE PLUS): The sofa is upholstered with stain repellant "Velvetine plus" fabric as a standard offering. The velvet fabric can be vacuum cleaned in order to remove dirt & grit from the fabric surface. Upholstery covers made from Velvetine fabric should not be soap washed or dry cleaned.Manufacturer should be a certified member of BIFMA for the last 10 years , SEFA-8 and should be following managment systems as per ISO 9001:2015, ISO 14001:2004, OHSAS 18001:2007 and energy management system as per ISO 50001:2011 in accordance with the TÜV NORD CERT auditing and certification procedures for Design, Development, Manufacturing, Marketing, Sales, Supply and Servicing of Home & Institutional, Interiors, Furniture, Accessories & Related Products and Provide Solutions for Home & Work Space and should have Green Guard Certification for few of its products also should have the service set up at least at district headquarter.

NOS

of 17

20 FU L52 MIDAS 2

SEATER SOFA

Supply and placement with following specifications The Midas sofa is a lounge seating system standing on beam with side frame assemblies. It is available in three different models: 2-seater, 1. LH/RH SIDE FRAME: The LH/RH side frame is fitted to the two ends of the seat/back mounting frame to form the leg assembly. It is made of SS J4 Grade tube 0 4.44 cm. x 1.5mm thk. 2. SEAT/BACK MOUNTING FRAME: The seat/back mounting frame assy. holds the two side frames together. The mounting frames, 2nos are used to connect the side frames. The mounting frame is made of MS. E.R.W. tube 05.08±0.03cm. x 3.15±0.0252cm thk. black painted. The seat/back is mounted on 4.0±0.03cm x 2.0±0.02cm x 0.2±0.016cm thk M.S. rectangular tube which is welded on the beam of seat/back mounting frame. 3. SEAT/BACK ASSEMBLY: The seat/back assembly consists of 1.2±0.1cm thk plywood insert with Polyurethane foam having density = 45 +1- 2 Kg/m3 and hardness of the P. U. foam = 18 to 22 kg on Hampden m/c for 25% compression of the foam. The complete moulded seat/back assembly is covered with a replaceable fabric upholstery cover. *SEAT/BACK SIZE: 54.5 cm. (W)-x- 46.7cm. (D) x 12.5cm. (T) 4. BOTTOM SHOES: The side frames are fitted with front and rear bottom shoes made of injection moulded polypropylene. 5. FABRIC (VELVETINE PLUS): The sofa is upholstered with stain repellant "Velvetine plus" fabric as a standard offering. The velvet fabric can be vacuum cleaned in order to remove dirt & grit from the fabric surface. Upholstery covers made from Velvetine fabric should not be soap washed or dry cleaned.Manufacturer should be a certified member of BIFMA for the last 10 years , SEFA-8 and should be following managment systems as per ISO 9001:2015, ISO 14001:2004, OHSAS 18001:2007 and energy management system as per ISO 50001:2011 in accordance with the TÜV NORD CERT auditing and certification procedures for Design, Development, Manufacturing, Marketing, Sales, Supply and Servicing of Home & Institutional, Interiors, Furniture, Accessories & Related Products and Provide Solutions for Home & Work Space and should have Green Guard Certification for few of its products also should have the service set up at least at district headquarter.

NOS

21 GLAZE COFFEE

TABLE

Supply and placement with following specifications TABLE LEGS

METERIALS & SIZE : OVAL METAL TUBE THICK 1.5 mm Color :SILVER

POWER COATING TABLE TOP MATERIALS & SIZE : (DENSITY / TYPE L

X W X T 1100 X 600 X 8 MM Color : PARTIAL BLACK TEMERED GLASS

TOP FULL BLACK TEMPERED GLASS TABLE BOTTOM MATERIALS &

SIZE : (DENSITY / TYPE) L X W X T 1100 X 600 X 6 MM Color : FULL

BLACK TEMPERED GLASS FINISHING: PARTIAL BLACK GLASS AND

SILVER POWDER COATING FRAME AND LEGS Manufacturer should be a










NOS

of 17

22 GLAZE

CORNER TABLE

Supply and placement with following specifications TABLE LEGS

METERIALS & SIZE : OVAL METAL TUBE THICK 1.5 mm Color :SILVER

POWER COATING TABLE TOP MATERIALS & SIZE : (DENSITY / TYPE L

X W X T 600 X 600 X 8 MM Color : PARTIAL BLACK TEMERED GLASS

TOP FULL BLACK TEMPERED GLASS TABLE BOTTOM MATERIALS &

SIZE : (DENSITY / TYPE) L X W X T 1100 X 600 X 6 MM Color : FULL

BLACK TEMPERED GLASS FINISHING: PARTIAL BLACK GLASS AND

SILVER POWDER COATING FRAME AND LEGS Manufacturer should be a










NOS

23 REFRIGERATOR Supply and placement with following refrigetor RD EDGE PRO 190 CT 5.2

LUSHWINE NOS

24 COMPUTER

TABLE C-9

Supply and placement with following specifications computer table companion

C9 with overall size 900 X 500X 750 mm (WXDXH).Manufacturer should be a










NOS

25 FLOYED

SINGLE BED

Supply and placement with following Specification for FLOYD BED Overall

Size: Width - 2036.0 mm Depth - 958.0 mm Height - 746.0 mm Material Body

panels are made of 18 mm thick Prelaminated Particle Board All the exposed

edges are edge banded with 2 mm thick PVC edge banding Bed structure consist

of metal frames made of M.S. 25 mm Square Pipes in 1.2 mm Thickness.

Hardware :The high quality hardware used Construction: Knock Down

construction. Finish: 18 mm thick Prelaminated Particle Board is in VALIGNY

OAK make – GODREJ (SHIRVAL). Metal frames are powder coated in shade

PANTONE S/G 410C to thickness of 50 microns (+-10). .Manufacturer should

be a certified member of BIFMA for the last 10 years , SEFA-8 and should be









NOS

26

SONATA

MATTRESS

78*36*3

Supply and placement with following specifications Overall Size : Length -

1981.0 mm Depth - 914.0 mm Thickness – 3 Inch RC Pad Thickness:- 9 mm RC

pad density :- 70 gm/dcm3 DRC centrifuged:- 20 % EPE sheet thickness :- 75

mm EPE sheet density :- 23 gm/dcm3 Quilting Foam Thickness :- 10 mm

Quilting Foam Density :- 18 gm/dcm3 Tapestry :- 80 gm Tapestry Nature:-

PolyCotton. The .Manufacturer should be a certified member of BIFMA for the

last 10 years , SEFA-8 and should be following managment systems as per ISO








NOS

of 17

27 TABLE T-101

Supply and placement with following specifications overall size w 1199 d 590 h

750 top worksurface the panels are made from 18+- 0.5 mm thk pre-laminated

boards as per with 2mm thick pvc edge banding on all sides made from 0.9 +- 0.9

mm thk powder coated 50 micrones CRCA MS. lock :- shell 0.5 +- 0.07 mm thk

CRCA MS drawer tray: 0.5 +- 0.07 mmthk CRCA MS drawer front 0.8 +-0.1 mm

thk CRCA MS lock 10 lever cam lock handles built in plastic.Manufacturer

should be a certified member of BIFMA for the last 10 years , SEFA-8 and should

be following managment systems as per ISO 9001:2015, ISO 14001:2004,

OHSAS 18001:2007 and energy management system as per ISO 50001:2011 in







NOS

28

STOREWEL

PLAIN

ALMIRAH

Supply and placement of Godrej make or equivalent as per design approve as per

order Storewel Plain Almirah 1. Models Plain with 4S2. Product Size: Plain (4S) - 916 mm (W) x 486 mm (D) x 1981 mm (H) DMX Drg.- ST-095, Rev.0 3. Construction & Material Welded construction.0.8 mm thk CRCA for Back, Shelf & 0.9 mm thk CRCA for all other components. 4. Configuration (Door) Full height Steel Hinged Door5. Locking & handle : Mazak Handle 3 way locking mechanism with shooting bolt arrangement.6. Shelving : Height wise Adjustable Shelf Mounting Uniformly Distributed Load Capacity per each full shelf is 80 Kg maximum Plain 4S : 4 Nos. of Adjustable Full Shelves. 7. Leveler M10 Screw type leveler with hex plastic base 8. Finish Epoxy Polyester Powder coated to the thickness of 50 microns (+/-10). Manufacturer should be a certified member of BIFMA,

SEFA-8 and should be following management systems as per ISO 9001:2015, ISO 14001:2004, OHSAS 18001:2007 and energy management system as per ISO 50001:2011 in accordance with the TÜV NORD CERT auditing and certification procedures for Design, Development, Manufacturing, Marketing, Sales, Supply and Servicing of Home & Institutional, Interiors, Furniture, Accessories & Related Products and Provide Solutions for Home & Work Space and should have Green Guard Certification for few of its products also should have the service set up at least at district headquarter.

NOS

29 GLASS DOOR

STOREWEL

Supply and placement with following specifications of Glass door strewel1.

Product Size: 915 mm (W) x 486mm (D) x 1981* mm (H) *- Height without

leveler. 2. Construction & Material § Welded construction.§ 0.8 mm thk CRCA

for Shelf & 0.9 mm thk CRCA for all other components. 3. Door • Glasses fitted

to full height steel frame. 4. Locking • 2 way locking mechanism with shooting

bolt. 5. Handle : • Chrome plated brass handle 6. Shelving : • Height wise

Adjustable Shelves 4 Nos. • Uniformly Distributed Load Capacity per full shelf is

80 Kg maximum 7. Leveler § M10 Screw type leveler with hex plastic base. (add

10mm to unit height and additional 10mm for adjustment.) 8. Finish § Epoxy

Polyester Powder coated to the thickness of 50 microns (+/-10). Manufacturer










NOS

of 17

30 4 DOOR VFC

Supply and placement with following specifications Models & Product Size 4

Drawer Width: 470mm Height: 1320mm Depth: 620mm Construction:Rigid

Knock Down Construction Material: CRCA 0.7 mm Thick (Top, Side & Drawer

Front); 0.6 mm Thick (Frames, Drawer- Inside Cover, Side Back Side) 0.5mm

Thick (Back, Bottom, Drawer Bottom) Drawer front: Easy to grip Full length

Handle recess integrated into Metal Drawer fronts Label Holder Snap on type

plastic label holder on Drawer Front Drawer Size & Files type For hanging ‘Ezee’

/ ‘Visa’ files (Foolscap) from front to back (Files Along theWidth) No. of 20 mm

thk file which can be hanged in above way per drawer is 28. Locking & anti-

tipping arrangement Centralized locking with 10 lever Cam Lock & having anti-

tipping arrangement to ensure thatwhen one drawer is opened for use, it does

notallow other drawers to be opened. Slide High quality precision ball slide.

Drawer Load: 40 kg. UDL for 75,000 cycles (BS) Triangular Plate Plain

Triangular plate pop riveted at the bottom corners for rigidity.Finish:Epoxy

Polyester Powder coated to the thickness of 50 microns (+/-10)Manufacturer










NOS

31 IMPRESS

TABLE

Supply and placement of Godrej make or equivalent as per design approve as per

order Impress Table MAIN TOP MDF + VENEER + PU Coating , Size : 1800 W *900D*750 H TOP THICKNESS – 65 mm MODESTY size : 1640 X 600 X16 MM MDF + Veneer + PU Coating MOBILE PEDESTAL MDF + Veneer + PU Coating , Size : 510W* 635H * 445D mm MDF + VENEER + PU Coating, Size : 1200W x 445D x 660 H TOP THICKNESS – 25 mm Manufacturer should be a certified member of

BIFMA, SEFA-8 and should be following management systems as per ISO 9001:2015, ISO 14001:2004, OHSAS 18001:2007 and energy management system as per ISO 50001:2011 in accordance with the TÜV NORD CERT auditing and certification procedures for Design, Development, Manufacturing, Marketing, Sales, Supply and Servicing of Home & Institutional, Interiors, Furniture, Accessories & Related Products and Provide Solutions for Home & Work Space and should have Green Guard Certification for few of its products also should have the service set up at least at district headquarter.

NOS

32 4 DOOR

BOOKCASE

Supply and placement of Godrej make or equivalent as per design approve as per order 4 door bookcase. Product size for 4 door bookcase 914mm W 320 mm D 1742 mm H Construction & material: Rigid knock Down construction. Top panel side panel and back panel are made from 0.7 mm high yield strength CRCA , rest in 0.8 mm CRCA. Configuration 4 door. Door Features / locking:- Each door has 6 lever cam lock with common key. Each door has 3mm thk transparent glass for clear inside vision secured in a metal frame through rubber gasket. Each door has a scissor mechanism for receding inside the top of respective compartment & ensure parallel & smooth movement. Each door has plastic side end caps as handel which is easy to grip. Behind Storage shelving:- Each compartment has storage shelf. Uniformly Distributed load capacity per each shelf is 80 kg maximum. Top Panel:- 4 door has inside metal top panel. Finish Epoxy polyester powder coated to the thickness of 50 micrones.(+/-10) Manufacturer should be a certified member of BIFMA, SEFA-8 and should be following management systems as per ISO 9001:2015, ISO 14001:2004, OHSAS 18001:2007 and energy management system as per ISO 50001:2011 in accordance with the TÜV NORD CERT auditing and certification procedures for Design,

NOS

of 17

Development, Manufacturing, Marketing, Sales, Supply and Servicing of Home & Institutional, Interiors, Furniture, Accessories & Related Products and Provide Solutions for Home & Work Space and should have Green Guard Certification for few of its products also should have the service set up at least at district headquarter.

33 FU7001 D

Supply and placement of Godrej make as per order High back Revolving Chair to

the following specification 1) SEAT/BACK ASSEMBLY: The seat / back are

made up of 1.2 cm thick hot pressed plywood, upholstered with fabric and

moulded Polyurethane foam together with moulded seat and back covers. The

back foam is designed with contoured lumbar support for extra comfort. The chair

is available in four models. PCH-7001D (HIGH BACK) SIZE: 50.0cm. (W) X

72.0cm. (H) SEAT SIZE: 50.0cm. (W) X 46.0cm. (D) 2) POLYURETHANE

FOAM: The Polyurethane foam is moulded with density = 45 +/-2 kg/m3 and

Hardness = 20 +/- 2 on Hampden machine at 25% compression. 3) SEAT /

BACK COVERS: For PCH-7001D the seat cover is injection moulded in black

co-polymer polypropylene and back cover is vacuum formed from ABS sheets.

4) ARMRESTS (for PCH-7001D): The one-piece armrests made of black integral

skin polyurethane with 50-70 Shore ‘A’ Hardness and reinforced with M.S. insert.

The armrests are scratch and weather resistant. The armrests are fitted to the seat

with seat/armrest connecting strip assembly made of 0.5cm. thk. HR steel. 5A)

CENTRE PIVOT MECHANISM (for PCH-7001D): The center pivot mechanism

is designed with the following features: 3600 revolving type. 17° maximum tilt on

pivot at center. Tilt tension adjustment. Upright locking. 6) PNEUMATIC

HEIGHT ADJUSTMENT(for PCH-7001D): The pneumatic height adjustment

has an adjustment stroke of 12.0 cm. 7) TELESCOPIC BELLOW

ASSEMBLY(for PCH-7001D): The bellow is 3 piece telescopic type and

injection moulded in black Polypropylene. 8) PEDESTAL ASSEMBLY(for

PCH-7001D): The pedestal is injection moulded in black 30% glass-filled Nylon

and fitted with 5 nos. twin wheel castors. The pedestal is 66.0cm. pitch-center dia.

(76.0 cm with castors). 9) TWIN WHEEL CASTORS(for PCH-7001D): The twin

wheel castors are injection moulded in 30% Glass Filled black Nylon.

Manufacturer should be a certified member of BIFMA and should be following

managment systems as per ISO 9001:2008, ISO 14001:2004, ISO 18001:2007

and energy management system as per ISO 50001:2011 in accordance with the

TÜV NORD CERT auditing and certification procedures for Design,

Development, Manufacturing, Marketing, Sales, Supply and Servicing of Home

& Institutional, Interiors, Furniture, Accessories & Related Products and Provide

Solutions for Home & Work Space and should have Green Guard Certification

for few of its products also should have the service set up at least at district

headquarter.

NOS

of 17

34 WORKSTATION

750X600

Supply and place of Godrej Make or equivalent workstation System offered- Tile based 'Spacio Plus'. panel thickness- 50 MM (APPROX), HT. - 1200 MM( APPROX), TILE CONFIGURATION FOR ALL PANELS : ABOVE WORKTOP LEVEL : FAB. MAGNETIC TILE, BELOW WORKTOP LEVEL :METAL, FIN- PRELAMINATE, RACEWAY - FOR MOUNTING OF SWITCHES : 150MM METAL RACEWAY AT SKIRTING LEVEL FOR ALL PANELS & INTEWRMEDIATE RACEWAY AT below WORKTOP LEVEL, WORKSURFACE : IN PRELAMINATED PARTICLE BOARD AND PVC LIPPING; BOARD THK. - 25MM & OF DIMENSIONS : RECTA - 750 MM X 600 MM D - 1 NOS, Manufacturer should be a certified member of BIFMA and should be following managment systems as per ISO 9001:2008, ISO 14001:2004, ISO 18001:2007 and energy management system as per ISO 50001:2011 in accordance with the TÜV NORD CERT auditing and certification procedures for Design, Development, Manufacturing, Marketing, Sales, Supply and Servicing of Home & Institutional, Interiors, Furniture, Accessories & Related Products and Provide Solutions for Home & Work Space and should have Green Guard Certification for few of its products also should have the service set up at least at district headquarter.

RUNNING

FEET

35 KBPT

Supply and place of Godrej Make or equivalent METAL KBPT with channel system. Manufacturer should be a certified member of BIFMA and should be following managment systems as per ISO 9001:2008, ISO 14001:2004, ISO 18001:2007 and energy management system as per ISO 50001:2011 in accordance with the TÜV NORD CERT auditing and certification procedures for Design, Development, Manufacturing, Marketing, Sales, Supply and Servicing of Home & Institutional, Interiors, Furniture, Accessories & Related Products and Provide Solutions for Home & Work Space and should have Green Guard Certification for few of its products also should have the service set up at least at district headquarter.

NOS

36 ROLLER

BLINDS

Supply and placement with following roller blinds Sq. Ft

sidho-kanho-birsha universityskbu.ac.in/cvs/notice/20170608154509.pdfsidho-kanho-birsha university...

Documents