25378 FPX DVL Fireplace 11/24/99 3:41 PM Page 1

Composite

C M Y CM MY CY CMY K

Shown with 24 karat goldplated Classic Arch™ face

™

25378 FPX DVL Fireplace 11/24/99 3:41 PM Page 2

Composite

C M Y CM MY CY CMY K

Top or Rear Vent -Install Virtually AnywhereThe 34 DVL features the option of installing the directvent chimney in either a vertical or rear ventconfiguration. This allows the fireplace to be installedvirtully anywhere, including in bedroom, baths andmobile homes.

34 DVL Direct Vent Large Fireplace

The Fireplace Xtrordinair 34 DVL(direct vent large) Fireplace

Heating SpecificationsHeating Capacity*BTU Input (NG)*BTU Input (LP)*Overall Efficiency*

AFUE*

600 to 2,000 Sq. Ft.40,000 (high) 19,000 (low)40,000 (high) 19,000 (low)82% (with minimum vent configuration)87% (with maximum vent configuration)

68%

FiveBeautiful FacesTo Choose From

COPYRIGHT 1999 T. I.Fireplace XtrordinairKirkland, WAWeb Address: http://www.fireplacextrordinair.com

PRINTED IN USA

Fireplace Xtrordinair reserves the right to alter or improve itsproducts at any time without notification.

Rated As A Wall FurnaceThis direct vent fireplace is so efficient it can beused as your primary heat source. It can heat upto 2,000 square feet.

Realistic “Fire-Pit” LogsThe flickering flames, glowing logs and emberscombine to create the most realistic fire ever seen ina gas appliance.

Variable Heat OutputA finely detailed grill transfers heat efficiently into yourhome. A 130 CFM thermostatically-controlled convectionfan is a standard feature.

Indoor Air QualityDirect vent gas technology completely isolates the combustionsystem from the home by using outside air for combustion,which maintains indoor air quality.

Heating SecurityA millivolt system ensures continued use and enjoymenteven if the power goes out.

Safety In MindA thermocouple safety switch shuts off gas in 30 seconds ifthe pilot goes out (meets CGA standard). This far exceedscurrent U.S. standards.

Classic Arch™24 Karat Gold Plated

The Model 34 fireplace features the trademark shape of the parallel arches of the Fireplace Xtrordinair. The arched viewingarea and parallel arched face combined with the delicate lace pattern, are unique design elements that have identified FireplaceXtrordinair to thousands of discerning homeowners for over a decade.

I

F

B

DC

A

Gas appliance performance can be affected by prevailing atmospheric conditions. Contact local building or fire officials about restrictions and installation requirements in your area.Heating capacity may vary depending on the degree of home insulation, floor plan and the ambient temperature zone of the area in which you live.

NOTE: Improper installation of your gas applianceor failure to operate it in accordance to the guidelinesdetailed in the Owner's Manual may negate yourwarranty and endanger your home and family.

*

Classic Arch™Brushed Nickel Plated

Classic Arch™Black Metallic Paint

Options• Wall Thermostat• Remote Control Thermostat• Wall Switch• Cast “Classic Pattern” Fireback• Cast “Brick Pattern” Fireback

E

ClassicFireback

BrickFireback

Minimum Fireplace & Framing Dimensions

A = Face to MantleB = Face to Top FacingC = Face to Side FacingD = Face to Side WallE = Hearth Extension - FrontF = Hearth Extension - Side

Clearances To Unprotected Combustible Surfaces

24"(max. 8” mantle depth)

18"6"

12"0"

6"

Please refer to fireplace clearance drawing at the right

The dimensions and clearances on this page are for reference only! Refer to theOwner’s Manual for operation and exact specifications prior to installation.

™

20 1/2"

44 1/4"

25 1/4"

43 7/8"

40 1/8"

46 1/2"

46 3/4"

*When the 34 DVL is installed flush to the floor anon-combustible hearth pad 3/4” thick is required.

When installed 3” or above, no hearth pad is required.

See Installation Manual for complete details.

Metropolitan™Black Metallic Paint

Metropolitan™24 Karat Gold Plated

Rear Vent - Floorto center of vent

34 1/4”

Top Vent - Back of unitto center of vent

7 1/8”

Tested and certified by OMNI-Test Laboratories, Inc to the combustion performance and constructionrequirements of ANSI Z21.88/CSA 2.33-2998, applicable sections of UL 307b, and CAN/CGA 2.17-M91.

Safety Testing

20 1/4"