SERVICE MANUALMain SectionI SpecificationsI Preparation for ServicingI Adjustment ProceduresI Schematic DiagramsI CBA’sI Exploded ViewsI Parts List

When servicing the deck mechanism, refer to MK14 Deck Mechanism Section.

Deck Mechanism Part No.: N2460FL

DVD RECORDER & VIDEO CASSETTE RECORDER

CWV20V6

STANDBY-ON REW F.FWD STOP/EJECT PLAY RECORD CHANNEL D.DUBBING

OPEN/CLOSE

SOURCEVCR DVD

S-VIDEO VIDEO AUDIOL R

SELECT STOP PLAY RECORD

VCR REC D.DUBBING

VCR DVD

TIMER REC DVD REC

IMPORTANT SAFETY NOTICE

Proper service and repair is important to the safe, reliable operation of all Funai Equipment. The service procedures recommended by Funai and described in this service manual are effective methods of performing service operations. Some of these service special tools should be used when and as recommended.

It is important to note that this service manual contains various CAUTIONS and NOTICES which should be carefully read in order to minimize the risk of personal injury to service personnel. The possibility exists that improper service methods may damage the equipment. It also is important to understand that these CAUTIONS and NOTICES ARE NOT EXHAUSTIVE. Funai could not possibly know, evaluate and advice the service trade of all conceivable ways in which service might be done or of the possible hazardous consequences of each way. Consequently, Funai has not undertaken any such broad evaluation. Accordingly, a servicer who uses a service procedure or tool which is not recommended by Funai must first use all precautions thoroughly so that neither his safety nor the safe operation of the equipment will be jeopardized by the service method selected.

Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.

MAIN SECTION

DVD RECORDER & VIDEO CASSETTE RECORDER

CWV20V6

TABLE OF CONTENTS

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1-1Laser Beam Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2-1Important Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3-1Standard Notes for Servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4-1Preparation for Servicing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5-1Cabinet Disassembly Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6-1Electrical Adjustment Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7-1 How to Initialize the DVD Recorder & VCR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-8-1Firmware Renewal Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9-1 Function Indicator Symbols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10-1Block Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11-1Schematic Diagrams / CBA’s and Test Points. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12-1Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13-1Wiring Diagram < VCR Section > . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-14-1Wiring Diagram < DVD Section > . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-14-2System Control Timing Charts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-15-1IC Pin Function Descriptions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-16-1Lead Identifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-17-1Exploded Views. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-18-1Mechanical Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-19-1Electrical Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-20-1

Main SectionI SpecificationsI Preparation for ServicingI Adjustment ProceduresI Schematic DiagramsI CBA’sI Exploded ViewsI Parts List

1-1-1 E9400SP

SPECIFICATIONS

< VCR Section >

Note: Nominal specs represent the design specs. All units should be able to approximate these – some will exceedand some may drop slightly below these specs. Limit specs represent the absolute worst condition that still mightbe considered acceptable; In no case should a unit fail to meet limit specs.

Description Unit Minimum Nominal Maximum Remark

1. Video

1-1. Video Output (PB) Vp-p 0.8 1.0 1.2 SP Mode

1-2. Video Output (R/P) Vp-p 0.8 1.0 1.2

1-3. Video S/N Y (R/P) dB 40 45SP Mode,W/O Burst

1-4. Video Color S/N AM (R/P) dB 37 41 SP Mode

1-5. Video Color S/N PM (R/P) dB 30 36 SP Mode

1-6. Resolution (PB) Line 230 245 SP Mode

2. Servo

2-1. Jitter Low µsec 0.07 0.12 SP Mode

2-2. Wow & Flutter % 0.3 0.5 SP Mode

3. Normal Audio

3-1. Output (PB) dBV -9 -6 -3 SP Mode

3-2. Output (R/P) dBV -9 -6 -1.5 SP Mode

3-3. S/N (R/P) dB 36 41 SP Mode

3-4. Distortion (R/P) % 1.0 4.0 SP Mode

3-5. Freq. resp (R/P) at 200Hz dB -11 -4 SP Mode

(-20dB ref. 1kHz) at 8kHz dB -14 -4 SP Mode

4. Tuner

4-1. Video output Vp-p 0.8 1.0 1.2 E-E Mode

4-2. Video S/N dB 39 42 E-E Mode

4-3. Audio output dB -10 -6 -2 E-E Mode

4-4. Audio S/N dB 40 46 E-E Mode

5. Hi-Fi Audio

5-1. Output dBV -12 -8 -4 SP Mode

5-2. Dynamic Range dB 70 85 SP Mode

5-3. Freq. resp (6dB B.W) Hz 20 ~ 20K SP Mode

1-1-2 E9400SP

< DVD Section >

NOTES:1. All Items are measured without pre-emphasis unless otherwise specified.2. Power supply : AC120 V 60 Hz

4. Ambient temperature : 5 °C ~ 40 °C

ITEM CONDITIONS UNIT NOMINAL LIMIT

1. VIDEO

1-1. Video Output 75 ohm load Vp-p 1.0

1-2. S-Video Output

Y (Luminance) 75 ohm load Vp-p 1.0

C (Chrominance) 75 ohm load Vp-p 0.286

1-3. Component Output

Y (Luminance) 75 ohm load Vp-p 1.0

Cb (Chrominance) 75 ohm load Vp-p 0.7

Cr (Chrominance) 75 ohm load Vp-p 0.7

2. AUDIO

2-1. Output Level Vrms 2.0

2-2. Frequency Response

DVD-VIDEO LPCM fs = 48kHz 20~22kHz dB ± 0.5

Audio CD fs = 44.1kHz 20~20 kHz dB ± 0.5

2-3. Signal/Noise Ratio

DVD-VIDEO LPCM dB 90

CD dB 90

REC & Playback Input: 2 Vrms, Rec Speed: XP dB 80

2-4. Dynamic Range

DVD-VIDEO LPCM dB 80

CD dB 80

REC & Playback Input: 2 Vrms, Rec Speed: XP dB 80

2-5. THD+N 1 kHz, 0 dB

DVD-VIDEO LPCM % 0.01

CD % 0.01

REC & Playback Input: 2 Vrms, Rec Speed: XP % 0.01

1-2-1 R3NLSP

LASER BEAM SAFETY PRECAUTIONS

This DVD player uses a pickup that emits a laser beam.

The laser beam is emitted from the location shown in the figure. When checking the laser diode, be sure to keep your eyes at least 30 cm away from the pickup lens when the diode is turned on. Do not look directly at the laser beam.

CAUTION: Use of controls and adjustments, or doing procedures other than those specified herein, may result in hazardous radiation exposure.

Location: Inside Top of DVD mechanism.

Do not look directly at the laser beam coming from the pickup or allow it to strike against your skin.

Drive Mechanism Assembly

Laser Beam Radiation

Laser Pickup

Turntable

1-3-1 DVDN_ISP

IMPORTANT SAFETY PRECAUTIONS

Product Safety NoticeSome electrical and mechanical parts have special safety-related characteristics which are often not evident from visual inspection, nor can the protection they give necessarily be obtained by replacing them with components rated for higher voltage, wattage, etc. Parts that have special safety characteristics are identified by a # on schematics and in parts lists. Use of a substitute replacement that does not have the same safety characteristics as the recommended replacement part might create shock, fire, and/or other hazards. The Product’s Safety is under review continuously and new instructions are issued whenever appropriate. Prior to shipment from the factory, our products are carefully inspected to confirm with the recognized product safety and electrical codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally important to implement the following precautions when a set is being serviced.

Precautions during ServicingA. Parts identified by the # symbol are critical for

safety. Replace only with part number specified.

B. In addition to safety, other parts and assemblies are specified for conformance with regulations applying to spurious radiation. These must also be replaced only with specified replacements. Examples: RF converters, RF cables, noise blocking capacitors, and noise blocking filters, etc.

C. Use specified internal wiring. Note especially:

1) Wires covered with PVC tubing

2) Double insulated wires

3) High voltage leads

D. Use specified insulating materials for hazardous live parts. Note especially:

1) Insulation tape

2) PVC tubing

3) Spacers

4) Insulators for transistors

E. When replacing AC primary side components (transformers, power cord, etc.), wrap ends of wires securely about the terminals before soldering.

F. Observe that the wires do not contact heat producing parts (heat sinks, oxide metal film resistors, fusible resistors, etc.).

G. Check that replaced wires do not contact sharp edges or pointed parts.

H. When a power cord has been replaced, check that 5 - 6 kg of force in any direction will not loosen it.

I. Also check areas surrounding repaired locations.

J. Be careful that foreign objects (screws, solder droplets, etc.) do not remain inside the set.

K. Crimp type wire connector The power transformer uses crimp type connectors which connect the power cord and the primary side of the transformer. When replacing the transformer, follow these steps carefully and precisely to prevent shock hazards.Replacement procedure

1) Remove the old connector by cutting the wires at a point close to the connector. Important: Do not re-use a connector. (Discard it.)

2) Strip about 15 mm of the insulation from the ends of the wires. If the wires are stranded, twist the strands to avoid frayed conductors.

3) Align the lengths of the wires to be connected. Insert the wires fully into the connector.

4) Use a crimping tool to crimp the metal sleeve at its center. Be sure to crimp fully to the complete closure of the tool.

L. When connecting or disconnecting the internal connectors, first, disconnect the AC plug from the AC outlet.

1-3-2 DVDN_ISP

Safety Check after ServicingExamine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts, and wires have been returned to their original positions. Afterwards, do the following tests and confirm the specified values to verify compliance with safety standards.

1. Clearance Distance

When replacing primary circuit components, confirm specified clearance distance (d) and (d’) between soldered terminals, and between terminals and surrounding metallic parts. (See Fig. 1)

Table 1: Ratings for selected area

Note: This table is unofficial and for reference only. Be sure to confirm the precise values.

2. Leakage Current Test

Confirm the specified (or lower) leakage current between B (earth ground, power cord plug prongs) and externally exposed accessible parts (RF terminals, antenna terminals, video and audio input and output terminals, microphone jacks, earphone jacks, etc.) is lower than or equal to the specified value in the table below.

Measuring Method (Power ON):

Insert load Z between B (earth ground, power cord plug prongs) and exposed accessible parts. Use an AC voltmeter to measure across the terminals of load Z. See Fig. 2 and the following table.

Table 2: Leakage current ratings for selected areas

Note: This table is unofficial and for reference only. Be sure to confirm the precise values.

AC Line Voltage Clearance Distance (d), (d’)

120 V ≥ 3.2 mm (0.126 inches)

AC Line Voltage Load Z Leakage Current (i) Earth Ground (B) to:

120 V 0.15 µF CAP. & 1.5 kΩ RES. Connected in parallel i ≤ 0.5 mA Peak Exposed accessible parts

Chassis or Secondary Conductor

Primary Circuit

Fig. 1

d' d

AC Voltmeter (High Impedance)

Exposed Accessible Part

B Earth Ground Power Cord Plug Prongs

Z

Fig. 2

1-4-1 DVDN_SN

STANDARD NOTES FOR SERVICING

Circuit Board Indications1. The output pin of the 3 pin Regulator ICs is

indicated as shown.

2. For other ICs, pin 1 and every fifth pin are indicated as shown.

3. The 1st pin of every male connector is indicated as shown.

Instructions for Connectors1. When you connect or disconnect the FFC (Flexible

Foil Connector) cable, be sure to first disconnect the AC cord.

2. FFC (Flexible Foil Connector) cable should be inserted parallel into the connector, not at an angle.

Pb (Lead) Free SolderWhen soldering, be sure to use the Pb free solder.

How to Remove / Install Flat Pack-IC

1. Removal

With Hot-Air Flat Pack-IC Desoldering Machine:

1. Prepare the hot-air flat pack-IC desoldering machine, then apply hot air to the Flat Pack-IC (about 5 to 6 seconds). (Fig. S-1-1)

2. Remove the flat pack-IC with tweezers while applying the hot air.

3. Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6)

4. Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6)

CAUTION:

1. The Flat Pack-IC shape may differ by models. Use an appropriate hot-air flat pack-IC desoldering machine, whose shape matches that of the Flat Pack-IC.

2. Do not supply hot air to the chip parts around the flat pack-IC for over 6 seconds because damage to the chip parts may occur. Put masking tape around the flat pack-IC to protect other parts from damage. (Fig. S-1-2)

Top View

Out In

Bottom ViewInput

5

10

Pin 1

Pin 1

FFC Cable

Connector

CBA

* Be careful to avoid a short circuit.

Fig. S-1-1

1-4-2 DVDN_SN

3. The flat pack-IC on the CBA is affixed with glue, so be careful not to break or damage the foil of each pin or the solder lands under the IC when removing it.

With Soldering Iron:

1. Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder flux which is applied to all pins of the flat pack-IC, you can remove it easily. (Fig. S-1-3)

2. Lift each lead of the flat pack-IC upward one by one, using a sharp pin or wire to which solder will not adhere (iron wire). When heating the pins, use a fine tip soldering iron or a hot air desoldering machine. (Fig. S-1-4)

3. Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6)

4. Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6)

Hot-airFlat Pack-ICDesolderingMachine

CBA

Flat Pack-IC

Tweezers

Masking Tape

Fig. S-1-2

Flat Pack-IC Desoldering Braid

Soldering Iron

Fig. S-1-3

Fine TipSoldering Iron

SharpPin

Fig. S-1-4

1-4-3 DVDN_SN

With Iron Wire:

1. Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder flux which is applied to all pins of the flat pack-IC, you can remove it easily. (Fig. S-1-3)

2. Affix the wire to a workbench or solid mounting point, as shown in Fig. S-1-5.

3. While heating the pins using a fine tip soldering iron or hot air blower, pull up the wire as the solder melts so as to lift the IC leads from the CBA contact pads as shown in Fig. S-1-5.

4. Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6)

5. Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6)

Note: When using a soldering iron, care must be taken to ensure that the flat pack-IC is not being held by glue. When the flat pack-IC is removed from the CBA, handle it gently because it may be damaged if force is applied.

2. Installation1. Using desoldering braid, remove the solder from

the foil of each pin of the flat pack-IC on the CBA so you can install a replacement flat pack-IC more easily.

2. The “” mark on the flat pack-IC indicates pin 1. (See Fig. S-1-7.) Be sure this mark matches the 1 on the PCB when positioning for installation. Then presolder the four corners of the flat pack-IC. (See Fig. S-1-8.)

3. Solder all pins of the flat pack-IC. Be sure that none of the pins have solder bridges.

To Solid Mounting Point

Soldering Iron

Iron Wire

or

Hot Air Blower

Fig. S-1-5

Fine TipSoldering IronCBA

Flat Pack-ICTweezers

Fig. S-1-6

Example :

Pin 1 of the Flat Pack-ICis indicated by a " " mark. Fig. S-1-7

Presolder

CBA

Flat Pack-IC

Fig. S-1-8

1-4-4 DVDN_SN

Instructions for Handling Semi-conductorsElectrostatic breakdown of the semi-conductors may occur due to a potential difference caused by electrostatic charge during unpacking or repair work.

1. Ground for Human Body

Be sure to wear a grounding band (1 MΩ) that is properly grounded to remove any static electricity that may be charged on the body.

2. Ground for Workbench

Be sure to place a conductive sheet or copper plate with proper grounding (1 MΩ) on the workbench or other surface, where the semi-conductors are to be placed. Because the static electricity charge on clothing will not escape through the body grounding band, be careful to avoid contacting semi-conductors with your clothing.

<Incorrect>

CBA

Grounding Band

Conductive Sheet orCopper Plate

1MΩ

1MΩ

<Correct>

CBA

1-5-1 E9A80PFS

PREPARATION FOR SERVICING

How to Enter the Service Mode

About Optical Sensors

Caution:

An optical sensor system is used for the Tape Startand End Sensors on this equipment. Carefully readand follow the instructions below. Otherwise the unitmay operate erratically.

What to do for preparation

Insert a tape into the Deck Mechanism Assembly andpress the PLAY button. The tape will be loaded intothe Deck Mechanism Assembly. Make sure the poweris on, connect TP502 (S-INH) to GND. This will stopthe function of Tape Start Sensor, Tape End Sensorand Reel Sensors. (If these TPs are connected beforeplugging in the unit, the function of the sensors willstay valid.) See Fig. 1.

Note: Because the Tape End Sensors are inactive, donot run a tape all the way to the start or the end of thetape to avoid tape damage.

Q504

Q503

TP502S-INH

Fig. 1

1-6-1 E9AB1DC

CABINET DISASSEMBLY INSTRUCTIONS

1. Disassembly FlowchartThis flowchart indicates the disassembly steps to gainaccess to item(s) to be serviced. When reassembling,follow the steps in reverse order. Bend, route, anddress the cables as they were originally.

2. Disassembly Method

Note:(1): Identification (location) No. of parts in the figures(2): Name of the part(3): Figure Number for reference(4): Identification of parts to be removed, unhooked,

unlocked, released, unplugged, unclamped, ordesoldered.P=Spring, L=Locking Tab, S=Screw,CN=Connector*=Unhook, Unlock, Release, Unplug, or Desoldere.g. 6(S-1) = six Screws (S-1), 5(L-1) = five Locking Tabs (L-1)

(5): Refer to “Reference Notes.”

ID/LOC.No.

PART

REMOVAL

Fig.No.

REMOVE/*UNHOOK/UNLOCK/RELEASE/UNPLUG/DESOLDER

Note

[1] Top Cover D1 6(S-1) ---

[2]Front Assembly

D2*5(L-1), *3(L-2), *CN1609

11-11-21-3

[3]Front Bracket

D2 2(S-2), (S-3) ---

[4]Radiation Sheet

D2 ---------- ---

[5]Jack Bracket

D3 2(S-4) ---

[6] Jack CBA D3 Jack Earth Plate ---

[7]

DVD Mechanism & DVD Main CBA Assembly

D42(S-5A), 2(S-5B), *CN101, *CN701

---

[8] Dust Cover D4 ---------- ---

[1] Top Cover

[2] FrontAssembly

[4] Radiation Sheet

[3] FrontBracket

[5] Jack Bracket

[6] Jack CBA

[7] DVD Mechanism& DVD MainCBA Assembly

[9] RearPanel Unit

[10] PowerSupply CBA

[11] DC Fan Motor

[12] PCBHolder

[13] Rear Panel

[14] Bracket R

[16] DeckAssembly

[20] DeckPedestal

[18] DVD Open/Close SW CBA

[15] VCR Chassis Unit

[17] PowerSW CBA

[19] MainCBA

[21] FrontBracket R

[8] Dust Cover

[9]Rear Panel Unit

D56(S-6), 3(S-7), (S-8), *CN101, *CN102

---

[10]Power Supply CBA

D6 4(S-9), AC Cord ---

[11]DC Fan Motor

D6 2(S-10), Earth Plate ---

[12]PCB Holder

D6 3(S-11) ---

[13] Rear Panel D6 ---------- ---

[14] Bracket R D7 2(S-12) ---

[15]VCR Chassis Unit

D75(S-13), 6(S-14), (S-15), (S-16)

---

[16]Deck Assembly

D8(S-17), (S-18), Desolder

23

[17]Power SW CBA

D8 Desolder ---

[18]DVD Open/Close SW CBA

D8 Desolder ---

[19] Main CBA D8 ---------- ---

[20]Deck Pedestal

D9 8(S-19) ---

[21]Front Bracket R

D9 (S-20) ---

↓(1)

↓(2)

↓(3)

↓(4)

↓(5)

ID/LOC.No.

PART

REMOVAL

Fig.No.

REMOVE/*UNHOOK/UNLOCK/RELEASE/UNPLUG/DESOLDER

Note

1-6-2 E9AB1DC

Reference NotesCAUTION 1: Locking Tabs (L-1) and (L-2) are fragile.Be careful not to break them. 1-1. Release five Locking Tabs (L-1). 1-2. Release three Locking Tabs (L-2)1-3. Disconnect Connector (CN1609), and remove

the Front Assembly.2. When reassembling, solder wire jumpers as shown

in Fig. D8.3. Before installing the Deck Assembly, be sure to

place the pin of LD-SW on Main CBA as shown inFig. D8. Then, install the Deck Assembly whilealigning the hole of Cam Gear with the pin of LD-SW, the shaft of Cam Gear with the hole of LD-SWas shown in Fig. D8.

(S-1)

(S-1)

(S-1)

[1] Top Cover

Fig. D1

(L-1)

(S-2)

(S-2)(S-3)

(L-2)

(L-1)

(L-1)

[2] Front Assembly

[3] Front Bracket

[4] Radiation Sheet

CN1609

Fig. D2

Fig. D3

(S-4)

Jack Earth Plate

[5] Jack Bracket

[6] Jack CBA

[8] DustCover

Fig. D4

(S-5B)CN101

CN701

(S-5A)

[7] DVD Mechanism & DVD Main CBAAssembly

1-6-3 E9AB1DC

Fig. D5

(S-6)

(S-7)

(S-7)

(S-7)

CN102

CN101

(S-8)

[9] Rear Panel Unit

Fig. D6

(S-11)

(S-11)

(S-9)

(S-9)

AC Cord

Earth Plate

Hook

(S-9)

(S-10)

[13] Rear Panel

[10] Power Supply CBA

[12] PCB Holder

[11] DC Fan Motor

Fig. D7

(S-13)(S-13)

(S-13)

(S-14)

(S-14)

(S-15)

(S-16)

(S-14)

(S-14)(S-14)

(S-14)

(S-12)

[14] Bracket R

[15] VCR Chassis Unit

1-6-4 E9AB1DC

[19] Main CBA

[16] Deck Assembly

[17] Power SW CBA [18] DVD Open

/Close SW CBA

FE Head

Cylinder Assembly

ACE HeadAssembly

Desolder

Lead withblue stripe

Desolder

Lead withblue stripe

[19] Main CBA

SW512LD-SW

From FE Head

BOTTOM VIEWLead connections of Deck Assembly and Main CBA

Desolder

FromCapstan MotorAssembly

Printing side

Desolder

FromCylinder Assembly

FromACE HeadAssembly

Lead withblue stripe

Lead withblue stripe

DesolderLead withgray stripe

(S-17)

(S-18)

Fig. D8

LD-SW Pin

Hole

Hole

Shaft

Cam Gear

[19] Main CBA

[16] Deck Assembly

Pin

1-6-5 E9AB1DC

3. How to Eject ManuallyNote: When rotating the gear, be careful not to damage the gear.

1. Remove the Top Cover.

2. Rotate the gear in the direction of the arrow manually as shown below until the tray descends.

3. Pull the tray out manually and remove a disc.

Fig. D9

[20] Deck Pedestal

[21] Front Bracket R

(S-19)(S-19)

(S-20)

View for A

Rotate this gear in the direction of the arrowA

1-7-1 H9801EA

ELECTRICAL ADJUSTMENT INSTRUCTIONS

General Note: “CBA” is abbreviation for “Circuit Board Assembly.”

NOTE:

1. Electrical adjustments are required after replacing circuit components and certain mechanical parts. It is important to do these adjustments only after all repairs and replacements have been completed. Also, do not attempt these adjustments unless the proper equipment is available.

2. To perform these alignment / confirmation procedures, make sure that the tracking control is set in the center position: Press either [CHANNEL L] or [CHANNEL K] button on the front panel first, then the [PLAY] button on the front panel.

Test Equipment Required1. Oscilloscope: Dual-trace with 10:1 probe,

V-Range: 0.001~50 V/Div., F-Range: DC~AC-20 MHz

2. Alignment Tape (FL8A)

Head Switching Position AdjustmentPurpose: To determine the Head Switching position during playback.

Symptom of Misadjustment: May cause Head Switching noise or vertical jitter in the picture.

Note: TP751(V-OUT), TP302(RF-SW), VR501(Switching Point) --- Main CBA

Reference Notes:

Playback the Alignment tape and adjust VR501 so that the V-sync front edge of the CH1 video output waveform is at the 6.5H ± 1H (412.7 µs ± 63.5 µs) delayed position from the rising edge of the CH2 head switching pulse waveform.

Test point Adj. Point Mode Input

TP751(V-OUT)TP302(RF-SW)

GND

VR501(Switching Point)

PLAY (SP) -----

Tape Measurement Equipment Spec.

FL8A Oscilloscope 6.5H ± 1H(412.7µs±63.5µs)

Connections of Measurement Equipment

Figure 1

Oscilloscope

Main CBATP751

CH1 CH2Trig. (+)

GNDTP302

EXT. Syncronize Trigger Point

1.0HCH1

CH2

Switching Pulse

V-Sync0.5H

6.5H±1H (412.7µs±63.5µs)

1-8-1 E9A80INT

HOW TO INITIALIZE THE DVD RECORDER & VCR

To put the program back at the factory-default, initialize the DVD recorder & VCR as the following procedure.

< DVD Section >1. Turn the DVD recorder on.

2. Confirm that no disc is loaded or that the disc tray is open. To put the DVD recorder into the Version display mode, press [DVD], [CM SKIP], [1], [2], and [3] buttons on the remote control in that order. Fig. a appears on the screen.

3. Press [OK] button, then the DVD recorder starts initializing. When the initializing is completed, the DVD recorder exits the Version display mode and turns off the power automatically.

* To move into the Normal mode from the Version display mode, press [RETURN] button on the remote control instead of [OK] button.

* When [STANDBY-ON] button is pressed before [OK] button is pressed, the DVD recorder exits the Version display mode, then the power turns off.

MODEL NAME : *******

FE VERSION :BE VERSION : TT VERSION :

LD ADJUSTMENT : DISC ADJUSTMENT :

DEFAULT SETTING : ENTEREXIT : RETURN

R30_005_082R3F10210S1ET30015FSU

OKOK

*1: "*******" differs depending on the models.*2: Firmware Version differs depending on the models, and this indication is one example.

Fig. a Version Display Mode Screen

F/W VERSION DISP

1-9-1 E9AB0FW

FIRMWARE RENEWAL MODE

1. Turn the power on and remove the disc on the tray.

2. To put the DVD recorder into version up mode, press [DVD], [CM SKIP], [6], [5], and [4] buttons on the remote control unit in the order. Then the tray will open automatically.Fig. a appears on the screen.

3. Load the disc for version up.Fig. c appears on the screen. The file on the top is highlighted as the default.When there is only one file to exist, Step 4 will start automatically.

4. Select the firmware version pressing arrow buttons, then press [OK].Fig. d appears on the screen. The DVD recorder starts updating.

The appearance shown in (*1) of Fig. d is described as follows.

5. After updating is finished, the tray opens automatically.At this time, no button is available.

6. Pull out the AC code once, then insert it again.

Fig. a Version Up Mode Screen

* Firmware Version differs depending on the models, and this indication is one example.

Current F/W version is displayed.

Firm Update Mode

Please insert a disc.

ver. R3F10210S1E

Fig. c Update Disc Screen

* Firmware Version differs depending on the models, and this indication is one example.

Disc name is displayed.

Firm Update Mode ver. R3F10210S1E

VOL_200512250934

1 R3F10210S1E 2 R3F10211S1E 3 R3F10212S1E 4 R3F10213S1E

1 / 1

Files includedin the disc are displayed.

No. Appearance State

1 File Loading... Sending files into the memory

2Firmware Updating... XX% Complete.

Writing new version data

--- Firmware Update Failure Failed in updating

Fig. d Programming Mode Screen

* Firmware Version differs depending on the models, and this indication is one example.

Selected F/W version is displayed.

Firm Update Mode ver. R3F10210S1E

R3F10210S1E

File Loading...(*1)

1-10-1 E9A12FIS

FUNCTION INDICATOR SYMBOLS< VCR Section >

Note:If a mechanical malfunction occurs, the power is turned off. When the power comes on again after that by

pressing [STANDBY-ON] button, an error message is displayed on the TV screen for 5 seconds.

TV screenWhen reel or capstan mechanism is not functioningcorrectly

When tape loading mechanism is not functioning cor-rectly

When cassette loading mechanism is not functioningcorrectly

When the drum is not working properly

P-ON+5V Power safety detection

Led Mode Indicator Active

When reel or capstan mechanism is not functioning correctly

“A R” is displayed on a TV screen. (Refer to Fig. 1.)

When tape loading mechanism is not functioning correctly

“A T” is displayed on a TV screen. (Refer to Fig. 2.)

When cassette loading mechanism is not functioning correctly

“A C” is displayed on a TV screen. (Refer to Fig. 3.)

When the drum is not working properly “A D” is displayed on a TV screen. (Refer to Fig. 4.)

P-ON+5V Power safety detection “A P” is displayed on a TV screen. (Refer to Fig. 5.)

A RSP 0:00:00

Fig. 1

A TSP 0:00:00

Fig. 2

A CSP 0:00:00

Fig. 3

A DSP 0:00:00

Fig. 4

A PSP 0:00:00

Fig. 5

1-10-2 E9A12FIS

< DVD Section >

Note: If an error occurs, a message with the error number appears on the screen.

Message Solution Error No. Error Description Priority

Can not record on this disc.Insert the recordable disc, and ensure the disc status satisfies the recording requirements.

1 An error occurs during data reading. -

2 There is no reply for 15 seconds in Test Unit Ready. -

3 Cannot write the data after trying three times. -

4 An error occurs with OPC. -

5 During recovery in a record. -

6 An error occurs even if recovery has been tried three times. -

7 An error occurs in a format. -

8 It cannot start an encode. -

9 NV_PCK/RDI_PCK is not in encoded data. -

10 Encode Pause condition continued for 10 minutes. -

11 Encode Pause condition continued in normal REC condition for 10 minutes. -

12 Difference in the address and can not get StreamID of RDI/VIDEO. -

13 It is a reply that “ATAPI is not readable.” -

14 Cannot write the data after recovering SMALL VMGI. -

15 Cannot write the data after DVD-R Reverse Track. -

16 An error occurs in Finalize Close. -

17 An error occurs in Rec Stop Close. -

18 An error occurs in PCA Full (DVD_R). -

19 Safety Stop occurs during editing. -

20 High Speed Disc. 2

21 The disc is not formatted. 5

22 Disc Error has occurred. 3

24 The disc except DVD-R/RW or finalized DVD-R. 1

This program is not allowed to be recorded.

You cannot record copy prohibited programs.

25 During the Macrovision picture input. 11

26 During the CGMS picture input. 12

This disc is protected and not recordable.

Release the disc protect setting in the Disc Setting menu.

29 Disc Protected Disc. 7

Recording Error

You cannot record on this disc as Power Calibration Area is full.

E35 Error No.

Error message

1-10-3 E9A12FIS

If an error occurs during the timer recording, one of the following error numbers (40 to 42) or the above error messages (error number: 1 to 46) is displayed on the recording menu after timer recording.(Once the timer programming list with error indication is displayed, the program line(s) with error will be cleared only after the programs are cancelled and reset to the timer standby mode.)(In the case of the error occurs during setting the timer programming, no error messages is displayed.)

Disc is full. (No area for new recording)

Insert the recordable disc with enough recording space. 30 No avilable recording space. 5

You cannot record on the disc as Power Calibration Area is full.

Insert a new disc. 35 PCA is Full. (in REC start) 4

This disc is already finalized. Release the finalizing for this disc. 36 It is finalized. (Video Format Disc) 6

Can not record on this disc. Repeat the same operation.

37 Access to Memory Area range outside. -

38 Sector Address is wrong. -

39 BUP writing error of chapter editing. -

You cannot record more than 49 titles on the disc.(The maximum is 49.)

Delete unnecessary titles. 43 Its recording capacity has been reached. 9

You cannot record more than 254 chapters on the disc.(The maximum is 254.)

Delete unnecessary chapter marks. 44 The 254 chapter has been reached. 10

This program is not recordable in +VR mode.

You cannot record copy prohibited programs. 45 During the CGMS picture input. 12

The disc has a different menu layout. (Set “Replace Disc Menu” to ON to rewrite the menu.)

Set “Replace Disc Menu” to “ON” to rewrite the menu,after that you will record to.

46Trying to record onto the +VR formatting disc that had been recorded by the other recorder.

7

Message Solution Error No. Error Description Priority

Error message is not displayed.

- Set the timer programming correctly.

- Set the timer programming before the start time.

- Insert a recordable videotape with a record tab.

40

- Some portion has not been recorded because of program overlapping.

- Recording did not start at the start time.- No Videotape is inserted.

Videotape ran out during recording.

-

Turn the power on and set the clock correctly then set timer programming again.

41 Power failed -

Insert the recordable disc. 42 No disc when recording -

Message Solution Error No. Error Description Priority

Timer Programming

2. ---

3. ---

4. ---

5. ---

6. ---

7. ---

8. ---

* JAN/01 12:57AM 1:57AM 8 DVD E40

VCR DVD

A program with the error number is grayed out and asterisked on the timer programming list.

The speed mode changes to the error number.

1-11-1

BLOCK DIAGRAMSSystem Control Block Diagram

E9AB1BLS

86

KE

Y-

2

KE

Y-

1

S-D

AT

A-O

UT

SY

S-R

ES

ET

S-D

AT

A-I

NS

-CLK

RE

AD

Y/B

US

Y

PO

WE

R

CN

2212

CN

2211

D56

1

PO

WE

RS

W60

1K

EY

SW

ITC

H(V

CR

)

KE

Y S

WIT

CH

(DV

D)

TP

502

S-I

NH

44

PO

WE

R-S

W1

1A

L+5V

22

PO

WE

R-L

ED

PO

WE

R S

W C

BA

DV

D O

PE

N/C

LO

SE

S

W C

BA

CN

2210

CN

2209

OP

EN

/CLO

SE

SW

615

DU

BB

ING

SW

617

4S

YS

-RE

SE

T

2R

DY

3S

UB

-TX

D

1S

UB

-RX

D5

SU

B-S

CLK

4 23 1 5

CN

201

CN

2204

Q51

0

Q50

9X

552

CN

701

CN

101

BU

FF

ER

27M

HZ

X'T

AL

SY

S-R

ES

ET

RD

Y

SU

B-T

XD

SU

B-R

XD

SU

B-S

CLK

CLK

27 O

UT

CLK

27 IN

IC10

1

IC10

6

MA

IN M

ICR

O

CO

NT

RO

LLE

R

22

OPEN

/CLO

SE-S

W1

1D

UBB

ING

-SW

85

AL+

5V

AL+

5V

RF

-SW

D-V

SY

NC

C-S

YN

C-I

N

V-E

NV

RE

SE

TC

-RO

TA

D-R

EC

D-R

EC

VC

R-A

UD

IO-M

UT

EA

UD

IO-M

UT

E

AU

DIO

-MU

TE

RF

-SW

D-V

SY

NC

C-S

YN

C

V-E

NV

C-R

OT

A

IC50

1(S

YS

TE

M C

ON

TR

OL)

2523988324502931

Q50

1

RE

SE

TT

IME

R+

5V

P-O

N-L

PW

R-S

W27 43 91

H-A

-SW

99H

-A-S

WH

-A-C

OM

P10

0H

-A-C

OM

P

55O

UT

PU

T-S

ELE

CT

YC

A-S

CL

YC

A-S

DA

YC

A-C

S

YC

A-S

CL

19Y

CA

-SD

A20

YC

A-C

S21

YC

A-S

CL

YC

A-S

DA

YC

A-C

S

TO

VID

EO

B

LOC

K D

IAG

RA

M

TO

VID

EO

OU

TP

UT

SE

LEC

T

BLO

CK

DIA

GR

AM

TO

VID

EO

INP

UT

SE

LEC

T

BLO

CK

DIA

GR

AM

TO

AU

DIO

INP

UT

/OU

TP

UT

S

ELE

CT

BLO

CK

DIA

GR

AM

TO

AU

DIO

B

LOC

K D

IAG

RA

M

TO

Hi-F

i AU

DIO

B

LOC

K

DIA

GR

AM

TO

PO

WE

R S

UP

PLY

B

LOC

K D

IAG

RA

M

IIC-B

US

SD

A

IIC-B

US

SC

L

1718IIC

-BU

S S

CL

IIC-B

US

SD

A

NO

RM

AL-

L78

Hi-F

i-H-S

W

Hi-F

i/NO

R-I

NH

i-Fi-H

-SW

30

OU

TP

UT

-SE

LEC

T

OU

TP

UT

-SE

LEC

T

RE

MO

TE

-VID

EO

5R

EM

OT

ES

EN

SO

R

RS

501

IIC-B

US

SC

L

IIC-B

US

SD

A

6061A

UD

IO-S

W1

AU

DIO

-SW

2

56D

VD

-AU

DIO

-MU

TE

AU

DIO

-SW

1A

UD

IO-S

W2

DV

D-A

UD

IO-M

UT

E

59V

IDE

O-S

W1

VID

EO

-SW

257

VID

EO

-SW

3

58

VID

EO

-SW

1V

IDE

O-S

W2

VID

EO

-SW

3

FA

N-C

ON

T1

P-O

N-L

PW

R-S

WF

AN

-CO

NT

1

DV

D M

AIN

CB

A

92P

OW

ER

-LE

D

93P

OW

ER

-LE

D

J25

SY

S-R

ES

ET

T4

N24

N23

L25

R24

N2

N1

1344 12 11 2

RE

G-C

ON

T2

45

MA

IN C

BA

30R

EG

-CO

NT

230

RE

G-C

ON

T1

46 1P

-DO

WN

-HR

EG

-CO

NT

1P

-DO

WN

-H

+1.

2VR

EG

ULA

TO

RP

-ON

+1.2

VE

V+2

.4V

D56

5D

VD

-RE

CD

VD

-RE

C-L

ED

Q51

2

D56

6V

CR

-RE

CV

CR

-RE

C-L

ED

Q51

3

D57

7T

IME

RT

IME

R-L

ED

Q51

4

D50

2D

UB

BIN

GD

UB

BIN

G-L

ED

14

VC

R-L

ED

94V

CR

-LE

D95

Q51

1

D56

3V

CR

666463

DV

D-L

ED

96D

VD

-LE

D97

D56

2D

VD

1-11-2

Servo Block Diagram

E9AB1BLSV

SE

NS

OR

CB

A

SE

NS

OR

CB

A

CO

NT

RO

LH

EA

D

CL5

04

CN

502

CN

504

AC

HE

AD

AS

SE

MB

LY

C-F

G

C-C

ON

T

D-P

FG

ST

-S

T-R

EE

L

C-F

/R

CT

L(+

)

RE

C-

SA

F-S

W

PG

-DE

LAY

EN

D-S

IC50

1(S

ER

VO

CO

NT

RO

L)

6574

CT

L76

CT

L(-)

75 336788 81 3 3284 22

LM-F

WD

/RE

V26

D-C

ON

T34

(DE

CK

AS

SE

MB

LY

)

EN

D-S

T-R

EE

L

T-R

EE

L

ST

-S

ST

-S

Q50

4

Q50

3

Q50

6

SW

-PO

INTA

L+5V

VR

501

TP50

6TP

505

EN

D-S

TP50

7

SW

511

RE

C S

W

LD-S

W87

AL+

12V

AL+

5V

AL+

5VS

W51

2

AL+

18V

P-O

N+

5V(1

)

MO

DE

-SW

AL+

5V

D55

5S

-LE

D

5C

TL(

+)

6C

TL(

-)

1A

L+12

V(1

)2

P-O

N+

5V(1

)3

C-F

G4

C-F

/R

5C

-CO

NT

6G

ND

7LM

-FW

D/R

EV

8D

-CO

NT

9D

-PF

G

10G

ND

11A

L+12

V

12A

L+18

V

TP51

3C

TL

AL+

12V

(1)

MA

IN C

BA

CA

PS

TA

N M

OT

OR

C

YL

IND

ER

AS

SE

MB

LY

DR

UM

MO

TO

RPG

SE

NS

OR M

MLO

AD

ING

MO

TO

R

M

CA

PS

TA

NM

OT

OR

MO

TO

RD

RIV

EC

IRC

UIT

1-11-3

Digital Signal Process Block Diagram

E9AB1BLD

IC10

1 FR

ON

T-E

ND

DIG

ITA

LS

IGN

AL

PR

OC

ES

S

IC20

1 RF

/E

RR

OR

AM

P

IC30

1

MO

TOR

DR

IVE

R

MO

TOR

DR

IVE

R

IC20

2

OP

AM

P

IC30

2

IC10

4(F

LAS

H M

EM

OR

Y)

DV

D M

AIN

CB

A

TO V

IDE

OO

UT

PU

TS

ELE

CT

BLO

CK

DIA

GR

AM

TO V

IDE

OIN

PU

TS

ELE

CT

BLO

CK

DIA

GR

AM

TO A

UD

IOIN

PU

T/

OU

TP

UT

SE

LEC

TB

LOC

KD

IAG

RA

M

SP

DIF

BC

KD

ATA

LRC

K

MD

MC

SC

K

MS

BC

KD

ATA

LRC

K

SY

SC

LK

T2

G4

L4 K1

G3

U1

R3

U2

M25

K26

P24 T3

P2

R1

P3

R2

AIM

SR

26

VID

EO

-Y(I

/P)

VID

EO

-C

VID

EO

-Cb/

Pb

VID

EO

-Cr/

Pr

D/A

D/A

D/A

D/A

AU

DIO

I/F

VID

EO

EN

CO

DE

R

BA

CK

-EN

DD

IGIT

AL

SIG

NA

LP

RO

CE

SS

VID

EO

I/F

FLA

SH

ME

MO

RY

FE

E

NC

OD

ER

TR

AY O

PE

N

IC10

2,IC

103

(DD

R S

DR

AM

)

DD

R S

DR

AM

CN

201

DV

D M

EC

HA

NIS

M

TIL

T

TR

AC

KIN

G

FO

CU

S

PIC

K-U

P

SLE

D

MO

TO

R

M

RE

C V

IDE

O S

IGN

AL

PB

VID

EO

SIG

NA

LR

EC

AU

DIO

SIG

NA

L P

B A

UD

IO S

IGN

AL

EN

CO

DE

R C

BA

LPC

(MA

IN M

ICR

O C

ON

TR

OLL

ER

/MP

EG

2 A

V C

OD

EC

)

CN

1001

CN

1003

SP

IND

LE

MO

TO

R

MC

N10

02

RE

LA

Y C

BA

CN

301

+3.

3V

VID

EO

-Y/C

VB

SV

IDE

O-C

IC70

1(V

IDE

O D

EC

OD

ER

)

DE

CO

DE

RA

/D45

-50

Y2,

AA

4,

AB

1-A

B4

DE

CO

DE

RA

/D39

-44

V3,

Y3,

W1,

Y4,

W2,

AA

3

10 13

M4

VID

EO

-Y(I

)D

/A

1-11-4

Video Block Diagram

E9AB1BLV

MA

IN C

BA

RE

C V

IDE

O S

IGN

AL

PB

VID

EO

SIG

NA

L

OS

D C

HA

RA

CT

ER

MIX

47

49

IC50

1(O

SD

)

LUM

INA

NC

ES

IGN

AL

PR

OC

ES

S

VID

EO

(R

)-1

HE

AD

VID

EO

(L)

-1 H

EA

D

(D

EC

K A

SS

EM

BL

Y)

CN

253

1 2 3 4 5 6

VID

EO

AG

CR

P

R P

SY

NC

SE

PA

FB

C

Y/C

MIX

CC

D 1

HD

ELA

Y

R P

YN

R/C

OM

B F

ILT

ER

CH

RO

MIN

AN

CE

SIG

NA

L P

RO

CE

SS

IC30

1(V

IDE

O S

IGN

AL

PR

OC

ES

S/ H

EA

D A

MP

)26

57

28

QV

/QH

6dB

AM

P

TO

SY

ST

EM

CO

NT

RO

L B

LOC

K

DIA

GR

AM

TO

VID

EO

INP

UT

S

ELE

CT

BLO

CK

D

IAG

RA

M

TO

VID

EO

OU

TP

UT

S

ELE

CT

BLO

CK

D

IAG

RA

M

VC

R-V

IDE

O

DV

D-V

IDE

O(D

UB

)

VC

R

DV

D

TO

SY

ST

EM

CO

NT

RO

L B

LOC

K

DIA

GR

AM

CY

LIN

DE

R A

SS

EM

BL

Y

RF

-SW

RF

-SW

59V

-EN

VH

-A-S

WH

-A-C

OM

PH

-A-C

OM

P

TP30

2

VID

EO

(L)

-2 H

EA

D

VID

EO

(R

)-2

HE

AD

TP

301

C-P

B

D-V

-SY

NC

C-S

YN

C

D-V

-SY

NC

2553 24

YC

A-S

CL

14

3637

3934

Q30

1B

UF

FE

R

30

58 60

SP

EP

54Y

CA

-SD

A

55Y

CA

-CS

SE

RIA

LI/F

VC

AC

LAM

P

69 70

SP

HE

AD

AM

P

EP

HE

AD

AM

P

727374 656667

EN

V-D

ET

C-R

OT

A

C-R

OT

A/R

F-S

W

PB

/EE

-VID

EO

VC

R-V

IDE

O(D

UB

)T

O V

IDE

O IN

PU

T

SE

LEC

T B

LOC

K

DIA

GR

AM

TO

VID

EO

OU

TP

UT

S

ELE

CT

BLO

CK

D

IAG

RA

M

(VC

R

DV

D D

UB

BIN

G)

(DV

D

VC

R D

UB

BIN

G)

WF

2

WF

3

VID

EO(R

)-1VI

DEO

-CO

MVI

DEO

(L)-1

VID

EO(L

)-2VI

DEO

-CO

MVI

DEO

(R)-2

1-11-5

Video Input Select Block Diagram

E9AB1BLVIS

TO D

IGIT

AL

SIG

NA

L P

RO

CE

SS

BLO

CK

D

IAG

RA

M

RE

C V

IDE

O S

IGN

AL

MA

IN C

BA

22

Y-IN

21

1C

-IN

24

4V

IDE

O-I

N2

(VID

EO

INP

UT

SE

LEC

T)

IC80

5

JK14

01S

-VID

EO

IN

34

21

YY1

VIDE

O1

VIDE

O2

TU-V

IDEO

MUT

E

MUT

E

MUT

E

Y2

C1 C2

C

VID

EO

- IN

1

JK80

4

TU

900

(TU

NE

R U

NIT

) JK80

6S

-VID

EO

IN

2

34

21

YC

VID

EO

-IN

2

JK80

3

1317

1915 8 10 12 2

214

18

CN

1609

CN

1605

2223

24

VID

EO

-SW

2TO

SY

ST

EM

CO

NT

RO

LB

LOC

K D

IAG

RA

MV

IDE

O-S

W3

FR

ON

T J

AC

K C

BA

VID

EO

OU

T

CO

NT

RO

LLO

GIC

PB/E

E

BUFF

ERLP

F

BUFF

ERLP

F

DV

D M

AIN

CB

A

CN

701 10

10VI

DEO-

Y/CV

BS-IN

88

VID

EO

-C-I

N

CN

201

VC

R-V

IDE

OTO

VID

EO

BLO

CK

D

IAG

RA

M

Q13

03BU

FFER

Q13

04,Q

1305

BUFF

ER

VC

R-V

IDE

O(D

UB

)TO

VID

EO

B

LOC

K D

IAG

RA

M

VID

EO

-SW

1

(VC

R

DV

D D

UB

BIN

G)

WF

15

20BU

FFER

+

VID

EO

-Y/C

VB

SV

IDE

O-C

1-11-6

Video Output Select Block Diagram

E9AB1BLVOS

DV

D M

AIN

CB

A

MA

IN C

BA

CN

701 24

24VI

DEO-

Y(I/P

)-OUT

2222

VID

EO

-C-O

UT

2828

VIDE

O-Cb

/Pb-

OUT

2626

VIDE

O-C

r/Pr-O

UT

VID

EO

-Y(I

/P)

VID

EO

-CV

IDE

O-C

b/P

bV

IDE

O-C

r/P

r

JK14

02S

-VID

EO

O

UT

CN

201

34

21

IC14

05(V

IDE

O D

RIV

ER

)

4dB

AM

P2d

BA

MP

LPF

DR

IVE

R

YC

IC14

06(O

UT

PU

T S

ELE

CT

)

114d

BA

MP

2dB

AM

PLP

FD

RIV

ER

6

104d

BA

MP

2dB

AM

PLP

FD

RIV

ER

8

VID

EO

OU

T(C

OM

PO

SIT

E)

JK75

1

TP

751

V-O

UT

3

TO D

IGIT

AL

SIG

NA

L P

RO

CE

SS

BLO

CK

D

IAG

RA

M

DV

D-V

IDE

O(D

UB

)

SW

CT

L

PB

/EE

-VID

EO

TO S

YS

TE

M C

ON

TR

OL

BLO

CK

DIA

GR

AM

TO V

IDE

OB

LOC

K D

IAG

RA

M

RE

C V

IDE

O S

IGN

AL

PB

VID

EO

SIG

NA

L

WF

4

WF

5

WF

6

WF

1

WF

7W

F8

215

1

109

11

OU

TP

UT-

SE

LEC

T

Q39

1BU

FFER

TU

900

(TU

NE

R U

NIT

)

6V

IDE

O-I

N

(DV

D

VC

R D

UB

BIN

G)

IC14

04(V

IDE

O D

RIV

ER

)

54d

BA

MP

2dB

AM

PLP

FD

RIV

ER

68d

BA

MP

-6dB

DR

IVE

R

4dB

AM

P2d

BA

MP

LPF

DR

IVE

R

3 17

3030

VID

EO-Y

(I)-O

UT

VID

EO

-Y(I

)13

WF

12

VID

EO

-Cb/

Pb

OU

T

VID

EO

-YO

UT

VID

EO

-Cr/

Pr

OU

T

JK14

03

1-11-7

Audio Block Diagram

E9AB1BLA

RE

CA

MP

SE

RIA

LI/F

98

AU

TOB

IAS

11

P-O

N+

5V

P-O

N+

5V

Q42

1

BIA

SO

SC

Q42

2

Q42

6 (P

B=

ON

) Q42

5S

WIT

CH

ING

D-R

EC

OF

F

6E

QA

MP

LIN

EA

MP

MU

TE

LPF

10

SP

/LP

-ON

P

RALC

(AU

DIO

PR

OC

ES

S)

76 80 78

TU

NE

RLI

NE

1LI

NE

2

4AU

DIO

-PB/

REC

CN

504

3A

UD

IO-C

OM

1A

E-H

2A

E-H

/FE

-H

AU

DIO

HE

AD

AU

DIO

ER

AS

EH

EA

D

AC

HE

AD

AS

SE

MB

LY

FE

HE

AD

(DE

CK

AS

SE

MB

LY

)

1F

E-H

2F

E-H

-GN

D

CN

501

MA

IN C

BA

PB

-AU

DIO

SIG

NA

LR

EC

-AU

DIO

SIG

NA

L

5855

5354

D-R

EC

AU

DIO

-MU

TE

TO S

YS

TE

M

CO

NT

RO

L B

LOC

KD

IAG

RA

MF

ULL

ER

AS

EH

EA

D

YC

A-C

SY

CA

-SC

LY

CA

-SD

A

IC30

1

N-A

-OU

T

N-A

-IN

TO H

i-Fi A

UD

IOB

LOC

K D

IAG

RA

M

32

4

5

1-11-8 E9AB1BLAS

Audio Input/Output Select Block Diagram

DIG

ITA

LA

UD

IO O

UT

(CO

AX

1AL)

DV

D-A

UD

IO-M

UT

E

OU

TP

UT-

SE

LEC

T

JK12

02

JK80

5

AM

PQ

1351

Q80

4Q

806

AU

DIO

(L)

-OU

T1

MA

IN C

BA

FR

ON

T J

AC

K C

BA

AU

DIO

(R)

-OU

T1

JK80

1

AU

DIO

(L)

-IN

2

AU

DIO

(R)

-IN

2

JK80

0

JK80

4

AU

DIO

(L)

-IN

1

AU

DIO

(R)

-IN

1

SIF

OU

T

LIN

E(R

)-O

UT

MO

D-A

UD

IO

LIN

E(R

)-IN

LIN

E(L

)-O

UT

LIN

E(L

)-IN

DV

D-A

UD

IO(R

)D

VD

-AU

DIO

(L)

L-C

H

R-C

H

66

AUD

IO(L

)-IN

28

8AU

DIO

(R)-

IN2

(MT

S/S

AP

AU

DIO

S

IGN

AL

PR

OC

ES

S)

IC90

0(O

P A

MP

)IC

803

TU

900

(TU

NE

R U

NIT

)

MT

S/S

AP

A

UD

IOS

IGN

AL

PR

OC

ES

S

OP

A

MP

OP

A

MP

OP

A

MP

OP

A

MP

15A

UD

IO-I

N2

2130 29

1 7

2 6

(AU

DIO

INP

UT

SE

LEC

T)

VC

R P

B

IC80

0

3

2427

4 2 5 111 12 15 14

MU

TE

-ON

DR

IVE

Q80

5M

UT

E-O

N

910

CN

2204

CN

201

IN1

TU

IN2

(L-C

H)

IN1

IN1

IN1

TU

IN2

(R-C

H)

SW

CT

L

AU

DIO

-SW

2A

UD

IO-S

W1

TO S

YS

TE

M C

ON

TR

OL

BLO

CK

DIA

GR

AM

SW

CT

L

(OP

AM

P)

IC80

4

(OU

TP

UT

SE

LEC

T)

IC14

06

6 2

7 1

JK75

1

AU

DIO

(L)

-OU

T2

AU

DIO

(R)

-OU

T2

TO S

YS

TE

M C

ON

TR

OL

BLO

CK

DIA

GR

AM

TO S

YS

TE

M

CO

NT

RO

LB

LOC

K D

IAG

RA

M

TO H

i-Fi A

UD

IOB

LOC

K D

IAG

RA

M

IIC-B

US

SC

LIIC

-BU

S S

DA

TO S

YS

TE

M

CO

NT

RO

LB

LOC

K D

IAG

RA

M

CN

1609

CN

1605

RE

C A

UD

IO S

IGN

AL

PB

AU

DIO

SIG

NA

L

12 13 5 3

14 4

(DV

D

VC

R D

UB

BIN

G)

(VC

R

DV

D D

UB

BIN

G)

TP

754

A-O

UT-

LT

P75

3A

-OU

T-R

WF

10

WF

9

WF

11

SC

L11

SD

A12

WF

13

WF

14

910

11

IC80

1(A

UD

IO D

/A C

ON

VE

RT

ER

)

DV

D M

AIN

CB

A

2828

SP

DIF

1414

AUDI

O(L

)-OUT

1616

AUDI

O(R

)-OUT

1212

DVD-

AUDI

O-MU

TE20

20AU

DIO

(L)-

IN18

18AU

DIO

(R)-

IN

TO D

IGIT

AL

SIG

NA

L P

RO

CE

SS

BLO

CK

D

IAG

RA

MA

UD

IO D

/AC

ON

VE

RT

ER

7 6 8

15 14 164 3 5

IC80

2(A

UD

IO A

/D C

ON

VE

RT

ER

)

AU

DIO

A/D

CO

NV

ER

TE

R

7 8 9

13 14

6

SP

DIF

CN

101

CN

701

BC

KD

ATA

LRC

K

MD

MC

SC

K2

MS

AIM

S

L-C

HR

-CH

MU

TE

BC

KD

ATA

LRC

K

SY

SC

LK

R-C

HL-

CH

10 11 12

13

1-11-9 E9AB1BLH

Hi-Fi Audio Block Diagram

57

4847

1314

69 71 6 7 9

R-C

HIN

SE

L

L-C

HIN

SE

L

NO

RS

W

SE

RIA

LD

AT

AD

EC

OD

ER

OU

TP

UT

SE

LEC

T

VC

OLP

F

L-C

H B

PF

R-C

HP

NR

PIL

OT

DE

TCO

NT

ST

ER

EO

PLLS

TE

RE

OF

ILT

ER

SA

PF

ILT

ER

SA

PD

ET

SIF

DE

MO

DS

AP

DE

MO

DL-

RD

EM

OD

ST

/SA

PS

WM

AT

RIX

L-C

HP

NR

LIM

DE

V

CO

MP

SW

N

OIS

E

VC

OLP

FLI

MD

EV

CO

MP

CO

MP

DC

SW

N

OIS

E

dBX

DE

C

EN

VD

ETRIP

PLE

FIL

TE

R

DO

DE

T

MA

TR

IX

R-C

H B

PF

P R

R LPR

HO

LDP

ULS

E

NO

ISE

DE

T

ALC

3433

23 4 80 2 7837 38 54 77 1 39 26 24 27

LIN

E(R

)-IN

LIN

E(L

)-IN

N-A

-OU

T

DV

D-A

UD

IO(L

)D

VD

-AU

DIO

(R)

LIM

49

MU

TE

LIN

E(L

)-O

UT

M

OD

-AU

DIO

LIN

E(R

)-O

UT

N-A

-IN

Hi-F

i-H-S

WA

UD

IO-M

UT

E

NO

RM

AL-

L

TO

AU

DIO

B

LOC

K D

IAG

RA

M

IIC-B

US

SD

AIIC

-BU

S S

CL

P-O

N+

9V

TO

SY

ST

EM

CO

NT

RO

L B

LOC

KD

IAG

RA

M

MA

IN C

BA

Hi-F

i-AU

DIO

(R)

7H

i-Fi-C

OM

8H

i-Fi-A

UD

IO(L

)9

CN

253

IC45

1(M

TS

/ SA

P/ H

i-Fi A

UD

IO P

RO

CE

SS

/ Hi-F

i HE

AD

AM

P)

RE

C A

UD

IO S

IGN

AL

PB

AU

DIO

SIG

NA

LM

od

e :

SP

/RE

C

PIL

OT

CA

NC

EL

TO

AU

DIO

B

LOC

K

DIA

GR

AM

TO

SY

ST

EM

CO

NT

RO

L B

LOC

K

DIA

GR

AM

TO

SY

ST

EM

CO

NT

RO

L B

LOC

KD

IAG

RA

M

6263

DV

D A

UD

IO S

IGN

AL

74 12

Hi-F

iA

UD

IO(R

) H

EA

D

Hi-F

iA

UD

IO(L

) H

EA

D

CY

LIN

DE

RA

SS

EM

BL

Y

(DE

CK

AS

SE

MB

LY

)

TO

AU

DIO

IN

PU

T/O

UT

PU

TS

ELE

CT

B

LOC

K

DIA

GR

AM

TO

AU

DIO

IN

PU

T/O

UT

PU

TS

ELE

CT

BLO

CK

D

IAG

RA

M

1-11-10 E9AB1BLP

Power Supply Block Diagram

A

V

AC

1001

F10

011A

250

V

LIN

EF

ILT

ER

L100

1D

1001

- D

1004

BR

IDG

ER

EC

TIF

IER

2 4

Q10

01

Q10

03

Q10

08

8 7

34IC01

0E

RR

OR

VO

LTA

GE

DE

T

HO

T

CO

LD

T00

1

Q05

5

Q05

2

Q10

2 Q10

3

PO

WE

R S

UP

PL

Y C

BA

MA

IN C

BA

JUN

CT

ION

C

BA

F

HO

T C

IRC

UIT

. BE

CA

RE

FU

L.

20 19 18 17 16 15 14 13 12 11

11

AL+

44V

22

AL+

12V

(1)

33

AL+

12V

(2)

44

DV

D+

5V5

5A

L+5V

11

AL-

30V

33

AL+

2.4V

66

AL+

4V

CN

1607

CN

1610

CN

1612

CN

1608

CN

101

CN

1611

1 2

118

AL+

44V

217

AL+

12V

(1)

316

AL+

12V

(2)

415

DV

D+

5V5

14A

L+5V

109

AL-

30V

127

AL+

2.4V

154

AL+

4V

1F

AN

2G

ND

CN

102

TO

SY

ST

EM

CO

NT

RO

LB

LOC

K D

IAG

RA

M

P-O

N-L

EV

+33

VA

L+18

VA

L+12

VP

-ON

+9V

P-O

N+

5VA

L+5V

AL-

30V

EV

+10

.5V

PW

R-S

W

FA

N

TIM

ER

+5V

Q05

6

Q10

1

Q03

1

P-O

N+

5V

P-D

OW

N-H

P-O

N+

3.3V

EV

+2.

4V

P-O

N+

5VA

UD

IO+

5V

P-O

N+

11V

+9V

RE

G.

SW

+5V

SW

+5V

SW

+

11V

FAN

-CO

NT

1

Q10

7, Q

108

FA

NC

ON

TR

OL

Q10

4

Q10

5

Q05

7

SW

+5V

+3.

3V R

EG

IC15

03

+2.

5V R

EG

IC15

04

P-O

N+

2.5V

RE

G-C

ON

T1

SW

ITC

HIN

GQ

205

CA

UT

ION

!F

ixed

vol

tage

(or

Aut

o vo

ltage

sel

ecta

ble)

pow

er s

uppl

y ci

rcui

t is

used

in th

is u

nit.

If M

ain

Fus

e (F

1001

) is

blo

wn

, che

ck to

see

that

all

com

pone

nts

in th

e po

wer

sup

ply

circ

uit a

re n

ot d

efec

tive

befo

re y

ou c

onne

ct th

e A

C p

lug

to th

e A

C p

ower

sup

ply.

Oth

erw

ise

it m

ay c

ause

som

e co

mpo

nent

s in

the

pow

er s

uppl

y ci

rcui

t to

fail.

NO

TE

:T

he v

olta

ge fo

r pa

rts

in h

ot c

ircui

t is

mea

sure

d us

ing

hot G

ND

as

a co

mm

on te

rmin

al.

"Ce

sym

bole

rep

rèse

nte

un fu

sibl

e à

fusi

on r

apid

e."

CA

UT

ION

!F

or c

ontin

ued

prot

ectio

n ag

ains

t fire

haz

ard,

repl

ace

only

with

the

sam

e ty

pe fu

se.

AT

TE

NT

ION

: P

our

une

prot

ectio

n co

ntin

ue le

s ris

qes

d'In

cele

n'u

tilis

er q

ue d

es fu

sibl

e de

mêm

e ty

pe.

Ris

k o

f fi

re-r

epla

ce fu

se a

s m

arke

d."T

his

sym

bol m

eans

fast

ope

ratin

g fu

se."

A

V

F

1-12-1 D6N_SC

SCHEMATIC DIAGRAMS / CBA’S AND TEST POINTS

Standard Notes

WARNING

Many electrical and mechanical parts in this chassis have special characteristics. These characteristics often pass unnoticed and the protection afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage, etc. Replacement parts that have these special safety characteristics are identified in this manual and its supplements; electrical components having such features are identified by the mark “#” in the schematic diagram and the parts list. Before replacing any of these components, read the parts list in this manual carefully. The use of substitute replacement parts that do not have the same safety characteristics as specified in the parts list may create shock, fire, or other hazards.

Notes:1. Do not use the part number shown on these

drawings for ordering. The correct part number is shown in the parts list, and may be slightly different or amended since these drawings were prepared.

2. All resistance values are indicated in ohms (K = 103, M = 106).

3. Resistor wattages are 1/4W or 1/6W unless otherwise specified.

4. All capacitance values are indicated in µF (P = 10-6 µF).

5. All voltages are DC voltages unless otherwise specified.

1-12-2 D6N_SC

LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON THE FOLLOWING PAGES:

1. CAUTION:

FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, REPLACE ONLY WITH THE SAME TYPE FUSE. ATTENTION: POUR UNE PROTECTION CONTINUE LES RISQES D'INCELE N'UTILISER QUE DES FUSIBLE DE MÊME TYPE. RISK OF FIRE-REPLACE FUSE AS MARKED.

2. CAUTION:

Fixed Voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F1001) is blown, first check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail.

3. Note:1. Do not use the part number shown on the drawings for ordering. The correct part number is shown in the

parts list, and may be slightly different or amended since the drawings were prepared.

2. To maintain original function and reliability of repaired units, use only original replacement parts which are listed with their part numbers in the parts list section of the service manual.

4. Mode: SP/REC

5. Voltage indications for PLAY and REC modes on the schematics are as shown below:

6. How to read converged lines

7. Test Point Information

A V

F

This symbol means fast operating fuse.Ce symbole represente un fusible a fusion rapide.

2 31 5.0(2.5)

PLAY mode STOP mode5.0

The same voltage forboth PLAY & STOP modes Indicates that the voltage

is not consistent here.

< DVD Section >

2 31 5.0(2.5)< >

PLAY mode REC mode DVD mode

5.0

The same voltage forboth PLAY, REC & DVD modes

Indicates that the voltageis not consistent here.

< VCR Section > Unit: Volts

3

2

1

A B C D

1-B1

1-D3

AREA D3

AREA B1

1-D3

Distinction AreaLine Number (1 to 3 digits)

Examples:1. "1-D3" means that line number "1" goes to the line number "1" of the area "D3". 2. "1-B1" means that line number "1" goes to the line number "1" of the area "B1".

: Indicates a test point with a jumper wire across a hole in the PCB.

: Used to indicate a test point with a component lead on foil side.

: Used to indicate a test point with no test pin.

: Used to indicate a test point with a test pin.

1-12-3

Main 1/7 Schematic Diagram < VCR Section >

E9AB1SCM1

1-12-4

Main 2/7, Power SW, DVD Open/Close SW & Sensor Schematic Diagram < VCR Section >

E9AB1SCM2

1-12-5

Main 3/7 Schematic Diagram < VCR Section >

E9AB1SCM3

1-12-6

Main 4/7 Schematic Diagram < VCR Section >

E9AB1SCM4

1-12-7

Main 5/7 Schematic Diagram < VCR Section >

E9AB1SCM5

1-12-8

Main 6/7 Schematic Diagram < VCR Section >

E9AB1SCM6

1-12-9

Main 7/7 Schematic Diagram < VCR Section >

E9AB1SCM7

1-12-10

Power Supply & Junction Schematic Diagram < VCR Section >

E9AB1SCP

CAUTION !Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.If Main Fuse (F1001) is blown , check to see that all components in the power supplycircuit are not defective before you connect the AC plug to the AC power supply.Otherwise it may cause some components in the power supply circuit to fail.

"Ce symbole reprèsente un fusible à fusion rapide."

CAUTION !For continued protection against fire hazard,replace only with the same type fuse.ATTENTION : Pour une protection continue les risqesd'Incele n'utiliser que des fusible de même type.Risk of fire-replace fuse as marked.

"This symbol means fast operating fuse."

A V

F NOTE:The voltage for parts in hot circuit is measured usinghot GND as a common terminal.

1-12-11

Front Jack Schematic Diagram < VCR Section >

E9AB1SCJK

1-12-12

DVD Main 1/5 Schematic Diagram < DVD Section >

E9AB1SCD1

The order of pins shown in this diagram is different from that of actual IC101.IC101 is divided into five and shown as IC101 (1/5) ~ IC101 (5/5) in this DVD Main Schematic Diagram Section.

1 NOTE:

1-12-13

DVD Main 2/5 Schematic Diagram < DVD Section >

E9AB1SCD2

The order of pins shown in this diagram is different from that of actual IC101.IC101 is divided into five and shown as IC101 (1/5) ~ IC101 (5/5) in this DVD Main Schematic Diagram Section.

1 NOTE:

1-12-14

DVD Main 3/5 Schematic Diagram < DVD Section >

E9AB1SCD3

The order of pins shown in this diagram is different from that of actual IC101.IC101 is divided into five and shown as IC101 (1/5) ~ IC101 (5/5) in this DVD Main Schematic Diagram Section.

1 NOTE:

1-12-15 E9AB1SCD4

DVD Main 4/5 Schematic Diagram < DVD Section >

The order of pins shown in this diagram is different from that of actual IC101.IC101 is divided into five and shown as IC101 (1/5) ~ IC101 (5/5) in this DVD Main Schematic Diagram Section.

1 NOTE:

1-12-16

DVD Main 5/5 Schematic Diagram < DVD Section >

E9AB1SCD5

The order of pins shown in this diagram is different from that of actual IC101.IC101 is divided into five and shown as IC101 (1/5) ~ IC101 (5/5) in this DVD Main Schematic Diagram Section.

1 NOTE:

1-12-17

TO SENSOR CBA(START-SENSOR)

SW-PVR501

CTLTP513

RF-SWTP302WF2

C-PBTP301WF3

V-OUTTP751

WF1

TO SENSOR CBA(END-SENSOR)

S-INHTP502

BE9AB0F01011A

Main CBA Top View

Sensor CBA Top View

BHF300F01012A

BHF300F01012B

1-12-18

PIN21 OFTU900

PIN 6 OFTU900

WF11

WF12

PIN 11OFTU900

WF13

PIN 12 OFTU900

WF14

PIN 18 OFTU900

WF15

PIN 2 OFIC1406

WF6

PIN 14 OFCN201

PIN 26 OFCN201

WF8

PIN 28 OFCN201

WF7

WF9

PIN 22 OFCN201

WF5

PIN 24 OFCN201

WF4

PIN 28 OFCN2204

WF10

Main CBA Bottom View

BE9AB0F01011A

1-12-19 BE9A00F01021A

Power Supply CBA Top View

"Ce symbole reprèsente un fusible à fusion rapide."

CAUTION !For continued protection against fire hazard,replace only with the same type fuse.ATTENTION : Pour une protection continue les risqesd'Incele n'utiliser que des fusible de même type.Risk of fire-replace fuse as marked.

"This symbol means fast operating fuse."

A V

F

Because a hot chassis ground is present in the powersupply circut, an isolation transformer must be used.Also, in order to have the ability to increase the inputslowly, when troubleshooting this type power supplycircuit, a variable isolation transformer is required.

CAUTION !Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.If Main Fuse (F1001) is blown , check to see that all components in the power supplycircuit are not defective before you connect the AC plug to the AC power supply.Otherwise it may cause some components in the power supply circuit to fail.

NOTE:The voltage for parts in hot circuit is measured usinghot GND as a common terminal.

1-12-20 BE9A00F01021A

Power Supply CBA Bottom View

"Ce symbole reprèsente un fusible à fusion rapide."

CAUTION !For continued protection against fire hazard,replace only with the same type fuse.ATTENTION : Pour une protection continue les risqesd'Incele n'utiliser que des fusible de même type.Risk of fire-replace fuse as marked.

"This symbol means fast operating fuse."

A V

F

Because a hot chassis ground is present in the powersupply circut, an isolation transformer must be used.Also, in order to have the ability to increase the inputslowly, when troubleshooting this type power supplycircuit, a variable isolation transformer is required.

CAUTION !Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.If Main Fuse (F1001) is blown , check to see that all components in the power supplycircuit are not defective before you connect the AC plug to the AC power supply.Otherwise it may cause some components in the power supply circuit to fail.

NOTE:The voltage for parts in hot circuit is measured usinghot GND as a common terminal.

1-12-21

Front Jack CBA Top View Front Jack CBA Bottom View

DVD Open/Close SW CBA Top View DVD Open/Close SW CBA Bottom ViewPower SW CBA Top View Power SW CBA Bottom View

Junction CBA Top View Junction CBA Bottom View

BE9A00F01021B

BE9AB0F01011B BE9AB0F01011C

BE9AB0F01011D

1-13-1 W3NBWF

WF9

AUDIO(L)-OUT

Pin 14 of CN201

1V 0.5ms

WF7

VIDEO-Cb

Pin 28 of CN201

0.2V 20µs

WF8

VIDEO-Cr

Pin 26 of CN201

0.2V 20µs

SPDIF 1V 0.1µs

WF10 Pin 28 of CN2204

WF4 Pin 24 of CN201

VIDEO-Y 0.2V 20µs

WF5 Pin 22 of CN201

VIDEO-C 0.2V 20µs

WF6 Pin 2 of IC1406

VIDEO-CVBS 0.5V 20µs

WF14 Pin 12 of TU900

WF13 Pin 11 of TU900

WF15 Pin 18 of TU900

NOTE:Input: COLOR BAR SIGNAL (WITH 1KHz AUDIO SIGNAL)

WF3

WF1 UPPER

WF2

WF2

LOWER

TP751

TP302

UPPER

LOWER TP302

TP301

V-OUT 0.5V50µsRF-SW 5V

C-PB RF-SW 5V 5ms

0.2V

WF1 TP751

V-OUT E-E 0.2V 20µs

WF12

WF11 Pin 2 of TU900

Pin 6 of TU900

MOD-A 0.5V 0.2ms

MOD-V 0.5V 20µs

PLL-CLK 2V 2ms

PLL-DATA 2V 2ms

TU AUDIO 0.5V 0.2msTU VIDEO 0.2V 20µs

WAVEFORMS

WIRING DIAGRAM < VCR SECTION >

E9AB1WI1-14-1

AC

HE

AD

AS

SE

MB

LY

AU

DIO

ER

AS

EH

EA

D

CO

NT

RO

LH

EA

D

AU

DIO

HE

AD

CY

LIN

DE

R

AS

SE

MB

LY

CN

501

CN

502

CN

504

CN

253

CN

2209

CN

2211

W00

2C

N22

10

FU

LLE

RA

SE

HE

AD

FE

HE

AD

VID

EO

(R)1

HE

AD

VID

EO

(L)1

HE

AD

VID

EO

-IN

2

S-V

IDE

OIN

2

AU

DIO

(R)

-IN

2

AU

DIO

(L)

-IN

2

FR

ON

T

VID

EO

(L)2

HE

AD

VID

EO

(R)2

HE

AD

Hi-F

i A

UD

IO(R

) H

EA

D

Hi-F

i A

UD

IO(L

) H

EA

D

MA

IN C

BA

(DE

CK

AS

SE

MB

LY

)

SE

NS

OR

CB

A

DV

D O

PE

N/C

LO

SE

SW

CB

A

CN

2212 P

OW

ER

SW

CB

A

SE

NS

OR

CB

A

TO

WIR

ING

D

IAG

RA

M

<D

VD

SE

CT

ION

>

TO

DV

DM

AIN

CB

A

CN

101

(W01

)

TO

DV

DM

AIN

CB

AC

N70

1(W

02)

AN

T-I

NA

NT

-OU

TA

UD

IO(L

)-I

N1

AU

DIO

(R)

-OU

T2

VID

EO

IN1

AU

DIO

(L)

-OU

T2

AU

DIO

(R)

-IN

1V

IDE

O-Y

OU

T

VID

EO

-C

r/P

r O

UT

VID

EO

-C

b/P

b O

UT

AU

DIO

(R)

-OU

T1

AU

DIO

(L)

-OU

T1

S-V

IDE

OIN

S

-VID

EO

OU

TV

IDE

OO

UT

RE

AR

DIG

ITA

LA

UD

IOO

UT

OPEN

/CLOS

E-SW

22

DUBB

ING-

SW1

1

1

CN

1609

W03

CN

1605

FR

ON

T J

AC

K C

BA

C-I

N2

11

Y-I

N2

22

GN

D3

3V

IDE

O-I

N2

44

GN

D5

5AU

DIO

(L)-I

N26

6G

ND

77

AUDI

O(R

)-IN2

88

W00

1A

L+5V

11

GN

D3

3

GN

D3

3PO

WER

-SW

44

POW

ER-L

ED2

2

CN

102

2G

ND

FA

N

CN

1612

CN

1607

CN

101

CN

1610

CN

1608

CN

1611

JUN

CT

ION

CB

A

62 3 4 5 7 8 9 1 62 3 4 5 7 8 9

GN

D

AL+

44V

AL+

12V

(1)

AL+

12V

(2)

DV

D+

5VA

L+5V

GN

DG

ND

GN

D

AL-

30V

NU

AL+

2.4V

GN

DG

ND

AL+

4V NU

NU

PO

W-P

1 2 3 4 5 6 7 8 911 2 2 3 4 5 6

1 2 3 4 5 6

7 8 9 10 11 12

1 2 3 4 5 6 7 1 2 3 4 5 6 7 8 98 9

33 5 9 12 151 2 4 6 7 8 10 11 13 14 16 17 18

PO

WE

R S

UP

PL

YC

BA

AC

CO

RD

Hi-F

i-AU

DIO

(R)

Hi-F

i-CO

MH

i-Fi-A

UD

IO(L

)

VID

EO

-CO

MV

IDE

O(R

)-2

VID

EO

-CO

M

VID

EO

(L)-

2V

IDE

O(L

)-1

VID

EO

(R)-

1

AL+

12V

(1)

P-O

N+

5V(1

)

C-F

/RC

-FG

C-C

ON

TG

ND

LM-F

WD

/RE

VD

-CO

NT

D-P

FG

GN

DA

L+12

VA

L+18

V

FE

-HF

E-H

GN

D

AE

-HA

E-H

/FE

-HA

-CO

MA

UD

IO-P

B/R

EC

CT

L(+

)C

TL(

-)

1P

OW

-PN

U2

AL+

4V4

GN

D5

GN

D6

AL+

2.4V

7N

U8

AL-

30V

9G

ND

10G

ND

11G

ND

12G

ND

13A

L+5V

14D

VD

+5V

15A

L+12

V(2

)16

AL+

12V

(1)

17A

L+44

V18

NU

3

FAN

1

W00

3

W00

4

LOA

DIN

GM

OT

OR

CA

PS

TA

N

MO

TO

R

MD

RU

MM

OT

OR

PG

SE

NS

OR

M

CA

PS

TA

NM

OT

OR

MO

TO

RD

RIV

EC

IRC

UIT

M

CN

201

CN

2204

VID

EO

-Y(I

)30

GN

D29

VIDE

O-C

r/Pr-O

UT26

GN

D21

VID

EO

-C-O

UT

22

GN

D27

VIDE

O-C

b/Pb

-OUT

28

GN

D25

VIDE

O-Y

(I/P)

-OUT

24G

ND

23

GN

D15

AU

DIO

(R)-

IN18

GN

D19

AU

DIO

(L)-

IN20

GN

D17

AUD

IO(R

)-O

UT

16

AUD

IO(L

)-O

UT

14G

ND

13DV

D-AU

DIO

-MUT

E12

AU

DIO

+5V

11VI

DEO

-Y/C

VBS-

IN10

GN

D9

VID

EO

-C-I

N8

GN

D7

SU

B-S

CLK

5G

ND

6

SU

B-T

XD

3R

DY

2S

UB

-RX

D1

SY

S-R

ES

ET

4

SP

DIF

28G

ND

29

EV

+10

.5V

4E

V+

10.5

V5

EV

+10

.5V

6G

ND

7G

ND

8

GN

D12

GN

D13

P-O

N+

5V9

P-O

N+

5V10

P-O

N+

5V11

EV

+2.

4V19

EV

+2.

4V20

EV

+2.

4V21

GN

D17

GN

D18

RE

G-C

ON

T2

30

GN

D23

P-O

N+

2.5V

24P

-ON

+2.

5V25

GN

D22

GN

D26

GN

D27

P-O

N+

3.3V

14P

-ON

+3.

3V15

P-O

N+

3.3V

16

GN

D3

GN

D2

GN

D1

WIRING DIAGRAM < DVD SECTION >

E9AB1WID1-14-2

TO

MA

INC

BA

CN

2204

(W01

)

TO

WIR

ING

DIA

GR

AM

<V

CR

SE

CT

ION

>

TO

MA

INC

BA

CN

201

(W02

)

CN

701

VID

EO

-Y(I

)30

GN

D29

VIDE

O-C

r/Pr-O

UT26

GN

D21

VID

EO

-C-O

UT

22

GN

D27

VIDE

O-C

b/Pb

-OUT

28

GN

D25

VIDE

O-Y

(I/P)

-OUT

24G

ND

23

CN

101

GN

D15

AU

DIO

(R)-

IN18

GN

D19

AU

DIO

(L)-

IN20

GN

D17

AUD

IO(R

)-O

UT

16

AUD

IO(L

)-O

UT

14G

ND

13DV

D-AU

DIO

-MUT

E12

AU

DIO

+5V

11VI

DEO

-Y/C

VBS-

IN10

GN

D9

VID

EO

-C-I

N8

GN

D7

SU

B-S

CLK

5G

ND

6

SU

B-T

XD

3R

DY

2S

UB

-RX

D1

SY

S-R

ES

ET

4

SP

DIF

28G

ND

29

EV

+10

.5V

4E

V+

10.5

V5

EV

+10

.5V

6G

ND

7G

ND

8

GN

D12

GN

D13

P-O

N+

5V9

P-O

N+

5V10

P-O

N+

5V11

EV

+2.

4V19

EV

+2.

4V20

EV

+2.

4V21

GN

D17

GN

D18

RE

G-C

ON

T2

30

GN

D23

P-O

N+

2.5V

24P

-ON

+2.

5V25

GN

D22

GN

D26

GN

D27

P-O

N+

3.3V

14P

-ON

+3.

3V15

P-O

N+

3.3V

16

GN

D3

GN

D2

GN

D1

DV

D M

AIN

CB

A

DV

D M

EC

HA

NIS

M

PIC

KU

P

RE

LA

Y

CB

A

EN

CO

DE

R C

BA

CN

201

CN

1001

CN

1003

109

HW

(-)

910

HW

(+)

1F

CS

(+)

4T

RK

(-)

3T

RK

(+)

2F

CS

(-)

6T

ILT

(-)

5T

ILT

(+)

7F

PD

-VO

UT

9F

PD

-VC

C10

GN

D11

FP

D-V

SW

8F

PD

-VC

12G

ND

14R

F(+

)15

C16

B17

F18

E19

D20

PD

-SW

21H

22G

23A

24P

D-V

CC

25P

D-V

C26

VC

C1

27V

CC

228

TH

29G

ND

30G

ND

31IIN

R32

IINW

33IIN

E34

GN

D35

HF

SW

36E

NA

BLE

37O

CE

38G

ND

39O

CW

40LD

SW

13R

F(-

)

FO

CU

SA

CT

UAT

OR

TR

AC

KIN

GA

CT

UAT

OR

TIL

TA

CT

UAT

OR

DV

D/C

D

LAS

ER

D

IOD

E

DR

IVE

PD

IC

FPD

IC

CD

-LD

DV

D-L

D

SLE

DS

EN

SO

R

SP

IND

LEM

OT

OR

1 2 3

M

CN

301

181

SW

217

2S

W1

163

SL(

-)15

4S

L(+

)14

5G

ND

136

T-S

CN

212

7T-

SC

N3

118

VH

(-)

811

HV

(-)

712

HV

(+)

613

HU

(-)

514

HU

(+)

415

VC

C3

16U

217

V1

18W

CN

1002

MS

LED

MO

TO

R

1 11~

DV

D M

EC

HA

NIS

M &

DV

D M

AIN

CB

A A

SS

EM

BL

Y

1-15-1 W3N4HTI

SYSTEM CONTROL TIMING CHARTS

< VCR Section >

Mode SW: LD-SW

Note: EJ RS: Loading FWD (LM-FWD / REV “H”)RS EJ: Loading REV (LM-FWD / REV “L”)Stop (A) = LoadingStop (B) = Unloading

Note:

LD-SW Position detection A/D Input voltage Limit

(Calculated voltage)Symbol

3.76 V ~ 4.50 V (4.12 V) EJ

4.51 V ~ 5.00 V (5.00 V) CL

0.00 V ~ 0.25 V (0.00 V) SB

1.06 V ~ 1.50 V (1.21 V) TL

0.66 V ~ 1.05 V (0.91 V) FB

1.99 V ~ 2.60 V (2.17 V) SF

1.51 V ~ 1.98 V (1.80 V) SM

3.20 V ~ 3.75 V (3.40 V) AU

0.26 V ~ 0.65 V (0.44 V) AL

4.51 V ~ 5.00 V (5.00 V) SS

2.61 V ~ 3.19 V (2.97 V) RS

Note:

Symbol Loading Status

EJ Eject

CL Eject ~ REW Reel

SB REW Reel ~ Stop (B)

TL Stop (B) ~ Brake Cancel

FB Brake Cancel ~ FF / REW

SF FF / REW ~ Stop (M), (FF / REW)

SM Stop (M), (FF / REW) ~ Stop (A)

AU Stop (A) ~ Play / REC

AL Play / REC ~ Still / Slow

SS Still / Slow ~ RS (REW Search)

RS RS (REW Search)

1-15-2 W3N4HTI

Still/Slow Control Frame Advance Timing Chart

1) SP Mode

Fig. 1

23 RF-SW

F-AD(Internal Signal)

C-DRIVE

PB CTL

32 C-F/R

99 H-A-SW

98 C-ROTA

The first rise of RF-SW after a rise in F-AD signal

Acceleration Detection (T1)

AT"H"

"Z""H"

"L" "L"

Stop detection (T2)

ST Slow Tracking Value

BL Reversal Limit Value

STILL FRAME ADVANCE STILL

20ms

1-15-3 W3N4HTI

2) LP/SLP Mode

Fig. 2

23 RF-SW

F-AD(Internal Signal)

C-DRIVE

PB CTL

32 C-F/R

99 H-A-SW

98 C-ROTA

"H""Z"

"H"

"L" "L"

STILL STILL

AT

ST

BL

Stop detection (T2)

Acceleration Detection (T1) Slow Tracking Value

Reversal Limit Value

FRAME ADVANCE

The first rise of RF-SW after a rise in F-AD signal

20ms

1-15-4 W3N4HTI

Fig. 3

1. EJE

CT

(PO

WE

R O

FF

) -> CA

SS

ET

TE

IN (P

OW

ER

ON

) -> STO

P(B

) -> STO

P(A

) -> PL

AY

-> RS

-> FS

-> PL

AY

-> ST

ILL

-> PL

AY

-> STO

P(A

)

EJECT

CASS.LOAD

ST-S/END-S "OFF"

PLAY

REW

FF

PLAY

PLAY

STOP/EJECT

0.2S

0.7S

0.4S

0.2S

LD-FWD

STOP(A)

STOP(A)

LD-FWD

LD-REV

0.2S

LD-FWD

LD-FWD

LD-FWD

LD-FWD

LD-FWD

STILL(SLOW)

RS

FS

PLAY

PLAY

PLAY

0.2S

LD-REV

LD-REV

LD-FWD

LD-FWD

LD-REV

LD-REV

LD-REV

0.2S

0.5S

PIN

NO

.

CLEJ

SSSS

AUAU

TLL

D-S

W

CL

/SS

LM

-FW

D "M

"

/RE

V

C-D

RIV

E "Z"

ON

ON

C-F

/R

DR

UM

RO

TAT

ION

P-O

N-L

A-M

UT

E-H

D-R

EC

-H

D-P

B

PAUSE(SLOW)

AUAL

ALAU

SFSM

EJ

AU

RS

SF

SM

TL

FB

AL

SB

87

2632273129

TV

/VID

EO

9

PO

WE

R-O

FF

STO

PP

LA

YR

SF

SS

TIL

L(S

LO

W)

PL

AY

STO

PP

LA

YD

ISP

LA

Y

0.1S SBTL

SBFB

SMSM

SFAL

ALRS

AUAL

SSAU

ALSM

0.8S0.2S

0.3S

1.0S0.2S

1.5S (2H)2.5S (4H)

0.5S

0.2S

0.8S (2H)1.2S (4H)

0.2S

1.2S0.2S

20mS

0.4S

40mS

0.2S

0.2S

Refer to STILL/SLO

W TIM

ING

CHART Fig. 1, 2.

0.3S

0.2S

20mS

40mS

0.4S

0.2S

0.2S0.2S

0.3S

1-15-5 W3N4HTI

Fig. 4

PIN

NO

.

LD

-SW

CL

/SS

LM

-FW

D "M

"

/RE

V

C-D

RIV

E "Z"

ON

ON

C-F

/R

DR

UM

RO

TAT

ION

P-O

N-L

A-M

UT

E-H

D-R

EC

-H

D-P

B

EJ

AU

RS

SF

SM

TL

FB

AL

SB

87

2632273129

TV

/VID

EO

9

DIS

PL

AY

ST-S/END-S "ON"

REC

REW

FF

STOP/EJECT

0.5S

1.0S

0.2S

0.5S

0.2S

0.5S

0.5S

0.5S

0.2S

0.2S

0.2S

1.5S

2.5S Short REV

1.0S

0.2S

LD-FWD

REV

LD-FWD

STOP(A)

STOP(A)

STOP(A)

CASS. UNLD

EJECT

STOP(A)

LD-REV

FF

LD-REV

LD-REV

LD-FWD

LD-FWD

LD-FWD

LD-FWD

LD-FWD

LD-FWD

LD-FWD

REC PAUSE

REC

REC

REW

LD-REV

LD-REV

LD-REV

LD-REV

LD-REV

LD-REV

LD-REV

PAUSE

REC or PAUSE

STOP/EJECT

STOP/EJECT

STOP/EJECT

2. STO

P(A

) -> FF

-> STO

P(A

) -> RE

W -> S

TOP

(A) -> R

EC

-> PAU

SE

-> PAU

SE

or R

EC

-> STO

P(A

) -> EJE

CT

STO

PF

F

STOP

RE

WS

TOP

RE

CR

EC

RE

C PA

US

ES

TOP

TLTL

SMSM

SFSF

ALAL

SMAL

ALAL

AUAU

SMTL

SBEJ

RSRS

SMSM

SFFB

SMAU

AUSS

SSSS

SFAU

ALAL

AUSS

FBCL

SFFB

SMFB

SFAU

AUFB

SF

1.0S1.2S

0.2S0.2S

40mS

0.4S

0.2S0.2S

0.4S20m

S

40mS

0.2S

20mS

0.2S

0.4S

40mS

20mS

0.1S

1-15-6 W3N4HTI

< DVD Section >

INNER-SWopen?

Rezero 1

To discdistinction

Power on

Yes

Yes

No

Yes

Tray insertion

[ Tray Open ] button is pressed.

[ Tray Open ] button is pressed.

Tray ejection

Tray ejection completion

Push Close

Rezero 2

INNER-SWopen?

Is TimerET1 passed?

INNER-SWopen?

Is TimerET4 passed?

Is slit S5 passed?

Is TimerET3 passed?

Is TimerET1 passed?

Retry OK?

Is slit S1passed?

Is not slit passed?

Is TimerET2 passed?

No

No

Case 1

Case 2

Yes

Yes

YesYes

No

No

Case 4[ open ] button is pressed.

Case 5Retry.

Case 3[ open ] button is pressed.

No

No

Yes

Yes

Yes No

Yes

Yes

No

No

No

No

Tray insertion

In case of "No" by the 6th time retry.

1-15-7 W3N4HTI

Parameter

Tray open

V*: Voltage (HEX) S*: Encoder pulse (HEX) T*: Event timer ET*: Error

detection timer

V0: 2.0 V (00d) S1: 300 (12c) T1: 0.1 s ET1: 5.0 s

V1: 4.5 V (022) S2: 3300 (ce4) T2: 3.0 s ET2: 5.0 s

V2: 2.2 V (010) S3: 3935 (f5f) T3: 3.0 s ET3: 3.0 s

V3: 2.4 V (013) S4: 0 (000) T4: 0.1 s ET4: 3.0 s

V4: 6.0 V (030) S5: 3000 (bb8) T5: 0.1 s

SLED

Encoder pulse

INNER-SW

close

open

Tray insertion direction

Tray ejection direction

Timer ET1

S1

S2

S3

ET2

T1

V0

V2

V1

1-15-8 W3N4HTI

Tray close

Push close

SLED

INNER-SW

Timer

close

open

Tray insertion direction

Tray ejection direction

S5

V3

V4

S4

ET3 ET4

SLED

Encoder pulse

S5

T3

V3

V4

ET4

Push Close

INNER-SW

close

open

Tray insertion direction

Timer

1-15-9 W3N4HTI

Case 1

Case 2

Case 3 (When [OPEN] button is pressed before the S5 passage.)

Case 4 (When [OPEN] button is pressed after the S5 passage.)

It starts opening after making closing complete once.

SLED

open

Tray insertion direction

close

INNER-SW

TimerT2

Rezero 1

ET4

V3

V4

SLED

INNER-SW

open

Rezero 2

Tray insertion direction

Tray ejection direction

close

V0

V0

SLED

Encoder pulse

Tray ejection direction

T1Timer

V2

1-15-10 W3N4HTI

Case 5 (Retry.)

Retry frequency V1+

1st time retry 6 v

2nd time retry 7 v

3rd time retry 8 v

4th time retry 9 v

5th time retry 9 v

6th time retry 9 v

SLED

Tray ejection direction

S1

V1+

V2

6v

open

Tray insertion direction

Start retry.close

INNER-SW

1-16-1 E9AB0PIN

IC PIN FUNCTION DESCRIPTIONS

< VCR Section >

IC501 (SERVO/SYSTEM CONTROL/OSD)

“H” ≥ 4.5 V, “L” ≤ 1.0 V

Pin No.

IN/OUT

Signal Name Function

1 IN P-DOWN -H

Power Voltage Down Detector Signal

2 INREADY/BUSY

Ready/Busy Communication Control with Main Micro Controller

3 IN T-REEL Take Up Reel Rotation Signal

4 - NU Not Used

5 IN REMOCON-IN Remote Control Sensor

6 - NU Not Used

7 - NU Not Used

8 - NU Not Used

9 OUT TV/VIDEO RF Conv. ON/OFF Signal

10 OUT CONV-SW

RF Conv. Output Channel Switching Signal 3ch=”Hi-z”, 4ch=”L”

11 OUT S-CLK Communication of Clock with VCR Micro Controller

12 IN S-DATA-IN

Communication of Data to VCR Micro Controller

13 OUT S-DATA-OUT

Communication of Data from VCR Micro Controller

14 OUTDUBBING-LED

DUBBING-LED Output Signal Control

15 - NU Not Used

16 - NU Not Used

17IN/

OUTIIC-BUS- SDA IIC BUS Control Data

18 OUT IIC-BUS- SCL IIC BUS Control Clock

19 OUT YCA-SCL YCA IC Control Clock

20 OUT YCA-SDA YCA IC Control Data

21 OUT YCA-CS YCA IC Control Chip Select

22 INREC-SAF-SW

Recording Safety SW Detect (With Record tab = ”L”/ Without Record tab = ”H”)

23 OUT RF-SW Video Head Switching Pulse

24 OUTD-V SYNC Dummy V-sync Output

25 IN RESET System Reset Signal (Reset=”L”)

26 OUTLM-FWD/ REV

Loading Motor FWD/ REV Output

27 OUT P-ON-L Power On Signal to Low

28 - NU Not Used

29 OUT D-REC Delayed Record Signal

30 OUTHi-Fi-H-SW

Hi-Fi Audio Head Switching Pulse

31 OUTVCR-AUDIO-MUTE

VCR Audio Mute Control Signal

32 OUT C-F/RCapstan Motor FWD/REV Control Signal (FWD=”L”/REV=”H”)

33 OUT C-CONT Capstan Motor Control Signal

34 OUT D-CONT Drum Motor Control Signal

35 - NU Not Used

36 - VDD VDD (AL+5V)

37 OUT OSCO Main Clock Output 14.31818MHz

38 IN OSCI Main Clock Input 14.31818MHz

39 - VSS VSS (GND)

40 IN XI Main Clock Input

41 OUT XO Main Clock Output

42 - NU Not Used

43 OUT PWR-SW DVD Power Supply Control Signal

44 IN SYS-RESET

System Reset Signal (Reset=”L”)

45 OUT REG-CONT2

Power Regulator Control Signal

46 OUTREG-CONT1

Power Regulator Control Signal

47 OUTVIDEO-OUT

Composite Video Signal Output

48 - Vss VSS (GND)

49 IN VIDEO-IN Composite Video Signal Input

50 IN C-SYNC-IN

Composite Synchronized Pulse

51 - VDD2 VDD2 (AL+5V)

52 IN AFCC Low Pass Filter Input Signal For AFC

Pin No.

IN/OUT

Signal Name Function

1-16-2 E9AB0PIN

Notes:

Abbreviation for Active Level: PWM ----- Pulse Wide ModulationA/D -------- Analog - Digital Converter

53 OUT AFCLPF Low Pass Filter Output Signal For AFC

54 OUT VIDEO-MUTE Video Mute Control Signal

55 OUT OUTPUT-SELECT

Output Select (DVD=”L”/VCR=”H”)

56 OUTDVD-AUDIO-MUTE

DVD Audio Mute Control Signal

57 OUT VIDEO-SW3 Video Switching Signal 3

58 OUT VIDEO-SW2 Video Switching Signal 2

59 OUT VIDEO-SW1 Video Switching Signal 1

60 OUT AUDIO-SW2 Audio Switching Signal 2

61 OUT AUDIO-SW1 Audio Switching Signal 1

62 - NU Not Used

63 OUT DVD-REC-LED

DVD Rec Mode LED Signal Output

64 OUT VCR-REC-LED

VCR Rec Mode LED Signal Output

65 IN D-PFG Drum PG/FG Input Signal

66 OUT TIMER-LED

TIMER Rec Mode LED Signal Output

67 IN C-FG Capstan Motor Rotation Detection Pulse

68 - AFG GND

69 OUT VRO Servo Standard Voltage Output

70 IN VRI Servo Standard Voltage Input

71 - AVss AVSS (GND)

72 IN CTLA CTL Amp. AC GND

73 IN ADVV Power Supply

74 IN/OUT

CTL (+) Playback/Record Control Signal (+)

75 IN/OUT

CTL (-) Playback/Record Control Signal (-)

76 OUT CTL Amp. Output Control Signal for Test Point

77 - NU Not Used

78 INHi-Fi/NOR-IN

Audio Mode Input HiFi=”L”/ Normal=”H”

79 INDVD POWER-SAFETY

DVD Power Supply Safety Signal

Pin No.

IN/OUT

Signal Name Function

80 INVCR POWER-SAFETY

VCR Power Supply Safety Signal

81 IN END-S Tape End Position Detect Signal

82 IN AFC Automatic Frequency Control Signal

83 IN V-ENV Video Envelope Comparator Signal

84 INPG-DELAY

Video Head Switching Pulse Signal Adjusted Voltage

85 IN KEY-2 A/D Key Data Signal 2

86 IN KEY-1 A/D Key Data Signal 1

87 IN LD-SW Deck Mode Position Detector Signal

88 IN ST-S Tape Start Position Detector Signal

89 INDVD POWER-SAFETY2

DVD Power Supply Safety Signal

90 - NU Not Used

91 OUT FAN-CONT1 Fan Motor Control Signal

92 OUT POWER-LED Power LED Signal Output

93 OUT POWER-LED Power LED Signal Output

94 OUT VCR-LED VCR Mode LED Signal Output

95 OUT VCR-LED VCR Mode LED Signal Output

96 OUT DVD-LED DVD Mode LED Signal Output

97 OUT DVD-LED DVD Mode LED Signal Output

98 OUT C-ROTA Color Phase Rotary Changeover Signal

99 OUT H-A-SW Video Head Amp Switching Pulse

100 INH-A-COMP Head Amp Comparator Signal

Pin No.

IN/OUT

Signal Name Function

1-17-1 E9AB0LE

LEAD IDENTIFICATIONS

75

26

50

51

251

100

76

60

21

40

41

201

80

61

E C B E C B

81

EC

B1 E B2

C1 C2

41

1 2 3 4G D S

16 9

81

121

32 17

161

8 5

41

60

21

40

41

201

80

61

1

2

4

3

16 98 5 24 13

LA71205M-MPB-E

Note:A: AnodeK: CathodeE: EmitterC: CollectorB: BaseR: ReferenceS: SourceG: GateD: Drain

KRA103M-AT/PKRC103M-AT/PKTA1267-Y-AT/PKTC3193-Y-AT/PKTC3199-(BL,Y)-AT/PKTA1266-Y-AT/P

KTC3198-Y-AT/PKTC3203-Y-AT/P2SC3266-GR(TPE2 F)

PS2561A-1(W)

PT204-6B-12

KIA4558P/PUTC4580

CD4052BNSRCD4053BNSR

RN1511(TE85R.F)

PQ070XF01SZH 2SK3563

MM1637XVBE

MM1697AJBE AN5832SA-E1V

MM1636XWRELA72670BM-MPB-E

1: Anode2: Cathode3: Emitter4: Collector

MN101D10FYD

1-18-1 E9AB1CEX

EXPLODED VIEWS

Cabinet

RS501

2B16

DVD Mechanism & DVD Main CBA Assembly is supplied as a unit.

2B76

See Electrical Parts Listfor parts with this mark.

2L011

2L011

2L011

2L011

2L011

1B1

2L071

2L071

2L0712L071

2B10

2L0432L043

2B4

2L043

2L043

2L081

2L081

2L081

2L044

2L0442L100

2L044

2L0622L082

A4

A3

D'

2B2

2L013

2B3

2L033

2B31

2L033

2L045

2L045

2B19

2B14

A2

2L033

2L033

2L033

C

2L110

2L022

2L0212L054

2L052

W001

2L0172L017

2L017

2L0172L017

2B1

2L014

2L061

2L015

E'

E

D

2L015

2B11

A34

2B13

A34

A18

C'

A1X

A10

A14

W002

W03

W003

2L019

F1001

FM1001

AC1001

2B18

1B2

W004

W02

W01

RS501

2B16

2B17

Main CBA

DVD Open/Close SW CBA

Front Jack CBA

Junction CBA

Power Supply CBA

Power SW CBA

Sensor CBA

Sensor CBA

2B59

2L110

2L111

A B

B' A'

2L030

2L111

1-18-2 E9AB1PEX

Packing

S1

A14

S2

2B64

S2

S2

Unit

S3

Some Ref. Numbers are not in sequence.

X1

X22

X4

X20 X5 X2X3

S2

20060914 1-19-1 E9AB1CA

MECHANICAL PARTS LIST

PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.

NOTE: Parts that are not assigned part numbers (---------) are not available.

Ref. No. Description Part No.

A1X FRONT ASSEMBLY E9AB1CD 1VM222728

A2 TOP COVER E9AB1CD 1VM323296

A3 MAIN CHASSIS E9400UD 0VM101353H

A4 REAR PANEL E9A82CD 1VM222256

A10# RATING LABEL(U) E9AB1CD ----------

A14 LABEL BAR CODE HB400UD ----------

A18 TEL NUMBER LABEL H9811UD(SV2000) ----------

A34 FOOT H5100UD 0VM406940A

1B1 DECK ASSEMBLY CZD014/VM2460 N2460FL

2B1 DECK PEDESTAL E9600UD 1VM120055F

2B2 FRONT BRACKET E9400UD 0VM204534C

2B3 FRONT BRACKET R E9400UD 0VM416269A

2B4 EARTH PLATE E9600UD 1VM421163

2B10 HOLDER PCB E9400UD 0VM101354E

2B11 BRACKET R E9600UD 1VM421062C

2B13 JACK BRACKET E9400UD 0VM416273

2B14 CUSHION RUBBER E9400UD 0VM416664C

2B19 RADIATION SHEET E9610UD 1VM320666B

2B31 TAPE HIMELON H9206JD 0VM413956

2B59 JACK EARTH PLATE E9600UD 1VM320623

2B64 LABEL EAS L0951UB ----------

2B76 DUST COVER(PS) E9B34ED 1VM222682

FM1001 DC FAN MOTOR D06K-12TS7 01(AX) MMEZR12NH003

2L011 SCREW TAP TIGHT M3X5 BIND HEAD+BLK NI GBHC3050

2L013 SCREW S-TIGHT M3X6 BIND HEAD+ GBJS3060

2L014 SCREW S-TIGHT M3X6 BIND HEAD+ GBJS3060

2L015 SCREW M3X5 HEAD+ BIND S-TIGHT GBJS3050

2L017 SCREW S-TIGHT M3X8 BIND HEAD+ GBJS3080

2L021 SCREW P-TIGHT M3X8 BIND HEAD+ GBCP3080

2L022 SCREW S-TIGHT M3X6 BIND HEAD+ GBJS3060

2L030 SCREW P-TIGHT M3X8 BIND HEAD+ GBJP3080

2L033 SCREW S-TIGHT M3X6 BIND HEAD+ GBJS3060

2L043 SCREW P-TIGHT M3X8 BIND HEAD+ GBJP3080

2L044 SCREW P-TIGHT M3X8 BIND HEAD+ GBJP3080

2L045 SCREW P-TIGHT M3X8 BIND HEAD+ GBJP3080

2L052 SCREW P-TIGHT M3X6 BIND HEAD+ GBJP3060

2L054 SCREW P-TIGHT M3X6 BIND HEAD+ GBJP3060

2L061 SCREW P-TIGHT M3X6 BIND HEAD+ GBJP3060

2L062 SCREW B-TIGHT M3X8 BIND HEAD+ GBHB3080

2L071 SCREW P-TIGHT M3*10 WASHERHEAD+ GCJP3100

2L081 SCREW S-TIGHT M3*5 BIND+ 3*5 BIND+ GBHS3050

2L082 SCREW S-TIGHT M3*5 BIND+ 3*5 BIND+ GBHS3050

2L100 P-TIGHT SCREW M3X34 E9400UD 1VM420034A

2L110 SCREW S-TIGHT M3X10 BIND HEAD+ GBJS3100

2L111 SCREW P-TIGHT 3X14 BIND HEAD + GBJP3140

PACKINGS1 GIFT BOX CARTON E9AB1CD 1VM323332

S2 STYROFOAM E9400UD 0VM101363B

S3 SET BAG E7708UA 0DM400731D

ACCESSORIESX1 REMOTE CONTROL UNIT NB658CD NB658CD

X2 DRY BATTERY R6P/2S XB0M451T0001

X3 RF CABLE 2.5C-2V WPZ0901TM002

X4 ACCESSORY BAG E5700UD 0VM415576

X5 AV CORD WPZ0102TM015 WPZ0102TM015

X20# OWNERS MANUAL E9AB1CD 1VMN23219

X22 QUICK GUIDE E9AB1CD 1VMN23220

Ref. No. Description Part No.

20060914 1-20-1 E9AB1EL

ELECTRICAL PARTS LIST

PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.

NOTES:

1. Parts that are not assigned part numbers (---------) are not available.

2. Tolerance of Capacitors and Resistors are noted with the following symbols.

DVD MECHANISM & DVD MAIN CBA ASSEMBLY

MCV CBA

MAIN CBA

C.....±0.25% D.....±0.5% F.....±1%

G.....±2% J......±5% K.....±10%

M.....±20% N.....±30% Z.....+80/-20%

Ref. No. Description Part No.

1B2 DVD MECHANISM & DVD MAIN CBA ASSEMBLY

N78FECUN

Ref. No. Description Part No.

MCV CBAConsists of the following:

1VSA14904

MAIN CBA (MCV-A )POWER SW CBA (MCV-B)DVD OPEN/CLOSE SW CBA (MCV-C)FRONT JACK CBA (MCV-D)SENSOR CBA

----------------------------------------1VSA13725

Ref. No. Description Part No.

MAIN CBA (MCV-A )Consists of the following:

----------

CAPACITORSC055 ELECTROLYTIC CAP. 47µF/16V M CE1CMASDL470

C056 ELECTROLYTIC CAP. 22µF/16V M CE1CMASDL220

C103 ELECTROLYTIC CAP. 47µF/16V M CE1CMASDL470

C213 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104

C214 ELECTROLYTIC CAP. 100µF/6.3V M CE0KMASDL101

C215 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104

C222 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104

C223 ELECTROLYTIC CAP. 100µF/6.3V M H7 CE0KMASSL101

C224 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104

C227 ELECTROLYTIC CAP. 100µF/6.3V M H7 CE0KMASSL101

C228 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104

C301 ELECTROLYTIC CAP. 1µF/50V M H7 CE1JMAVSL1R0

C302 CHIP CERAMIC CAP.(1608) CH J 390pF50V CHD1JJ3CH391

C303 PCB JUMPER D0.6-P5.0 JW5.0T

C304 CHIP CERAMIC CAP.(1608) CH J 100pF50V CHD1JJ3CH101

C305 CHIP CERAMIC CAP.(1608) CH J 100pF50V CHD1JJ3CH101

C307 CHIP CERAMIC CAP.(1608) B K 1µF/10V CHD1AK30B105

C308 ELECTROLYTIC CAP. 47µF/6.3V M H7 CE0KMAVSL470

C309 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104

C310 ELECTROLYTIC CAP. 22µF/6.3V M H7 CE0KMAVSL220

C311 ELECTROLYTIC CAP. 1µF/50V M H7 CE1JMAVSL1R0

C312 CHIP CERAMIC CAP.(1608) B K 1µF/10V CHD1AK30B105

C313 ELECTROLYTIC CAP. 1µF/50V M H7 CE1JMAVSL1R0

C314 CHIP CERAMIC CAP.(1608) B K 1µF/10V CHD1AK30B105

C315 CHIP CERAMIC CAP.(1608) B K 1µF/10V CHD1AK30B105

C316 CHIP CERAMIC CAP.(1608) B K 1µF/10V CHD1AK30B105

C317 CHIP CERAMIC CAP.(1608) B K 1µF/10V CHD1AK30B105

C318 ELECTROLYTIC CAP. 22µF/6.3V M H7 CE0KMAVSL220

C319 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103

C320 CERAMIC CAP.(AX) Y M 0.01µF/16V CCA1CMT0Y103

C321 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103

C324 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103

C327 ELECTROLYTIC CAP. 47µF/6.3V M H7 CE0KMAVSL470

C328 ELECTROLYTIC CAP. 1µF/50V M H7 CE1JMAVSL1R0

C329 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103

C330 ELECTROLYTIC CAP. 1µF/50V M H7 CE1JMAVSL1R0

C331 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103

C332 ELECTROLYTIC CAP. 1µF/50V M H7 CE1JMAVSL1R0

C333 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104

C336 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103

C339 CHIP CERAMIC CAP.(1608) B K 0.047µF/50V CHD1JK30B473

C340 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104

C341 CHIP CERAMIC CAP.(1608) B K 0.047µF/50V CHD1JK30B473

C342 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104

C343 ELECTROLYTIC CAP. 47µF/6.3V M H7 CE0KMAVSL470

C346 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103

C391 ELECTROLYTIC CAP. 100µF/10V M CE1AMASDL101

C392 ELECTROLYTIC CAP. 470µF/6.3V M CE0KMASDL471

C401 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104

C404 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103

C405 ELECTROLYTIC CAP. 22µF/6.3V M H7 CE0KMAVSL220

C406 ELECTROLYTIC CAP. 33µF/6.3V M H7 CE0KMAVSL330

C407 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103

C408 CHIP CERAMIC CAP.(1608) B K 0.012µF/50V CHD1JK30B123

C409 ELECTROLYTIC CAP. 10µF/16V M H7 CE1CMAVSL100

C410 CHIP CERAMIC CAP.(1608) B K 2700pF50V CHD1JK30B272

C411 CHIP CERAMIC CAP.(1608) B K 1000pF50V CHD1JK30B102

C412 ELECTROLYTIC CAP. 4.7µF/25V M H7 CE1EMAVSL4R7

C413 CHIP CERAMIC CAP.(1608) B K 6800pF50V CHD1JK30B682

C422 ELECTROLYTIC CAP. 47µF/6.3V M H7 CE0KMAVSL470

C423 ELECTROLYTIC CAP. 220µF/6.3V M H7 CE0KMAVSL221

C424 CERAMIC CAP. B K 470pF500V CCD2JKS0B471

C425 FILM CAP.(P) 0.018µF/100V J CMA2AJS00183

C440 ELECTROLYTIC CAP. 0.1µF/50V M H7 CE1JMAVSLR10

C441 ELECTROLYTIC CAP. 0.1µF/50V M H7 CE1JMAVSLR10

C448 ELECTROLYTIC CAP. 4.7µF/50V M H7 CE1JMAVSL4R7

C449 ELECTROLYTIC CAP. 4.7µF/50V M H7 CE1JMAVSL4R7

C451 ELECTROLYTIC CAP. 47µF/16V M H7 CE1CMAVSL470

C452 ELECTROLYTIC CAP. 0.1µF/50V M H7 CE1JMAVSLR10

C453 ELECTROLYTIC CAP. 10µF/16V M H7 CE1CMAVSL100

C454 ELECTROLYTIC CAP. 1µF/50V M H7 CE1JMAVSL1R0

C455 ELECTROLYTIC CAP. 22µF/6.3V M H7 CE0KMAVSL220

C456 ELECTROLYTIC CAP. 10µF/16V M H7 CE1CMAVSL100

C457 ELECTROLYTIC CAP. 4.7µF/25V M H7 CE1EMAVSL4R7

C458 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103

C459 ELECTROLYTIC CAP. 22µF/6.3V M H7 CE0KMAVSL220

C460 CHIP CERAMIC CAP.(1608) B K 4700pF50V CHD1JK30B472

C461 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103

Ref. No. Description Part No.

20060914 1-20-2 E9AB1EL

C462 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103

C465 ELECTROLYTIC CAP. 4.7µF/25V M H7 CE1EMAVSL4R7

C466 ELECTROLYTIC CAP. 220µF/6.3V M H7 CE0KMAVSL221

C467 CHIP CERAMIC CAP.(1608) B K 0.022µF/50V CHD1JK30B223

C470 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104

C471 ELECTROLYTIC CAP. 22µF/6.3V M H7 CE0KMAVSL220

C472 CHIP CERAMIC CAP.(1608) B K 4700pF50V CHD1JK30B472

C473 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103

C474 ELECTROLYTIC CAP. 4.7µF/25V M H7 CE1EMAVSL4R7

C475 ELECTROLYTIC CAP. 10µF/16V M H7 CE1CMAVSL100

C476 ELECTROLYTIC CAP. 1µF/50V M H7 CE1JMAVSL1R0

C483 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104

C485 ELECTROLYTIC CAP. 4.7µF/25V M H7 CE1EMAVSL4R7

C502 ELECTROLYTIC CAP. 220µF/6.3V M CE0KMASDL221

C505 ELECTROLYTIC CAP. 22µF/10V M H7 CE1AMAVSL220

C507 ELECTROLYTIC CAP. 1µF/50V M H7 CE1JMAVSL1R0

C508 CHIP CERAMIC CAP.(1608) B K 0.022µF/50V CHD1JK30B223

C509 ELECTROLYTIC CAP. 220µF/6.3V M H7 CE0KMAVSL221

C513 CHIP CERAMIC CAP.(1608) CH D 10pF50V CHD1JD3CH100

C514 CHIP CERAMIC CAP. CH J 27pF50V CHD1JJ3CH270

C515 CHIP CERAMIC CAP.(1608) CH J 22pF50V CHD1JJ3CH220

C521 ELECTROLYTIC CAP. 47µF/25V M CE1EMASDL470

C522 CHIP CERAMIC CAP.(1608) B K 4700pF50V CHD1JK30B472

C523 CHIP CERAMIC CAP.(1608) CH J 100pF50V CHD1JJ3CH101

C525 CHIP CERAMIC CAP.(1608) B K 4700pF50V CHD1JK30B472

C527 CHIP CERAMIC CAP.(1608) B K 0.047µF/50V CHD1JK30B473

C529 CHIP CERAMIC CAP.(1608) B K 0.022µF/50V CHD1JK30B223

C530 ELECTROLYTIC CAP. 1µF/50V M H7 CE1JMAVSL1R0

C531 ELECTROLYTIC CAP. 10µF/16V M H7 CE1CMAVSL100

C532 ELECTROLYTIC CAP. 10µF/16V M H7 CE1CMAVSL100

C533 ELECTROLYTIC CAP. 47µF/6.3V M H7 CE0KMAVSL470

C534 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104

C535 ELECTROLYTIC CAP. 22µF/10V M H7 CE1AMAVSL220

C536 CHIP CERAMIC CAP.(1608) B K 1000pF50V CHD1JK30B102

C537 CHIP CERAMIC CAP.(1608) B K 1000pF50V CHD1JK30B102

C540 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103

C544 ELECTROLYTIC CAP. 220µF/6.3V M CE0KMASDL221

C545 ELECTROLYTIC CAP. 100µF/16V M H7 CE1CMAVSL101

C588 ELECTROLYTIC CAP. 100µF/6.3V H7 CE0KMAVSL101

C706 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103

C751 CHIP CERAMIC CAP.(1608) B K 1000pF50V CHD1JK30B102

C752 CHIP CERAMIC CAP.(1608) B K 1000pF50V CHD1JK30B102

C762 ELECTROLYTIC CAP. 4.7µF/50V M H7 CE1JMAVSL4R7

C766 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103

C777 ELECTROLYTIC CAP. 4.7µF/50V M H7 CE1JMAVSL4R7

C814 ELECTROLYTIC CAP. 2.2µF/50V M CE1JMASDL2R2

C818 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103

C819 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104

C820 ELECTROLYTIC CAP. 2.2µF/50V M CE1JMASDL2R2

C821 ELECTROLYTIC CAP. 22µF/16V M CE1CMASDL220

C822 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104

C823 ELECTROLYTIC CAP. 2.2µF/50V M CE1JMASDL2R2

C825 ELECTROLYTIC CAP. 2.2µF/50V M CE1JMASDL2R2

C826 ELECTROLYTIC CAP. 2.2µF/50V M CE1JMASDL2R2

C827 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104

C828 ELECTROLYTIC CAP. 100µF/6.3V M CE0KMASDL101

C829 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104

C835 ELECTROLYTIC CAP. 470µF/6.3V M CE0KMASDL471

C839 ELECTROLYTIC CAP. 1µF/50V M H7 CE1JMASSL1R0

C840 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104

C841 ELECTROLYTIC CAP. 1µF/50V M CE1JMASDL1R0

C844 ELECTROLYTIC CAP. 10µF/16V M H7 CE1CMAVSL100

C845 CHIP CERAMIC CAP.(1608) CH J 1000pF50V CHD1JJ3CH102

Ref. No. Description Part No.

C846 ELECTROLYTIC CAP. 470µF/6.3V M CE0KMASDL471

C847 CHIP CERAMIC CAP. CH J 220pF50V CHD1JJ3CH221

C848 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104

C850 ELECTROLYTIC CAP. 10µF/16V M H7 CE1CMAVSL100

C851 CHIP CERAMIC CAP.(1608) CH J 1000pF50V CHD1JJ3CH102

C852 CHIP CERAMIC CAP. CH J 220pF50V CHD1JJ3CH221

C853 ELECTROLYTIC CAP. 10µF/16V M H7 CE1CMAVSL100

C854 ELECTROLYTIC CAP. 10µF/16V M H7 CE1CMAVSL100

C863 ELECTROLYTIC CAP. 4.7µF/25V M CE1EMASDL4R7

C864 ELECTROLYTIC CAP. 4.7µF/25V M CE1EMASDL4R7

C900 ELECTROLYTIC CAP. 10µF/16V M CE1CMASDL100

C901 ELECTROLYTIC CAP. 0.33µF/50V M CE1JMASDLR33

C902 ELECTROLYTIC CAP. 3.3µF/50V M CE1JMASDL3R3

C903 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104

C904 CHIP CERAMIC CAP.(1608) B K 0.022µF/50V CHD1JK30B223

C905 ELECTROLYTIC CAP. 2.2µF/50V M CE1JMASDL2R2

C906 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104

C907 CHIP CERAMIC CAP.(1608) B K 0.033µF/50V CHD1JK30B333

C908 ELECTROLYTIC CAP. 2.2µF/50V M CE1JMASDL2R2

C909 ELECTROLYTIC CAP. 2.2µF/50V M CE1JMASDL2R2

C910 ELECTROLYTIC CAP. 2.2µF/50V M CE1JMASDL2R2

C911 ELECTROLYTIC CAP. 4.7µF/50V M CE1JMASDL4R7

C912 ELECTROLYTIC CAP. 2.2µF/50V M CE1JMASDL2R2

C913 ELECTROLYTIC CAP. 2.2µF/50V M H7 CE1JMASSL2R2

C916 CHIP CERAMIC CAP.(1608) CH J 1000pF50V CHD1JJ3CH102

C917 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104

C918 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104

C919 ELECTROLYTIC CAP. 0.33µF/50V M CE1JMASDLR33

C920 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104

C922 ELECTROLYTIC CAP. 2.2µF/50V M CE1JMASDL2R2

C923 ELECTROLYTIC CAP. 0.22µF/50V M CE1JMASDLR22

C925 ELECTROLYTIC CAP. 0.47µF/50V M CE1JMASDLR47

C926 ELECTROLYTIC CAP. 100µF/6.3V M CE0KMASDL101

C927 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104

C928 CHIP CERAMIC CAP.(1608) CH J 47pF50V CHD1JJ3CH470

C1323 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104

C1325 CHIP CERAMIC CAP.(1608) CH J 33pF50V CHD1JJ3CH330

C1333 CHIP CERAMIC CAP.(1608) CH J 33pF50V CHD1JJ3CH330

C1335 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104

C1351 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104

C1352 CHIP CERAMIC CAP.(1608) B K 1µF/10V CHD1AK30B105

C1354 CHIP CERAMIC CAP.(1608) CH J 100pF50V CHD1JJ3CH101

C1401 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104

C1403 ELECTROLYTIC CAP. 1µF/50V M H7 CE1JMASSL1R0

C1421 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103

C1423 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103

C1441 ELECTROLYTIC CAP. 1µF/50V M CE1JMASDL1R0

C1442 ELECTROLYTIC CAP. 470µF/6.3V M CE0KMASDL471

C1443 ELECTROLYTIC CAP. 470µF/6.3V M CE0KMASDL471

C1461 ELECTROLYTIC CAP. 1µF/50V M CE1JMASDL1R0

C1462 ELECTROLYTIC CAP. 470µF/6.3V M CE0KMASDL471

C1481 ELECTROLYTIC CAP. 1µF/50V M CE1JMASDL1R0

C1482 ELECTROLYTIC CAP. 470µF/6.3V M CE0KMASDL471

C1523 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104

C1524 ELECTROLYTIC CAP. 100µF/6.3V M CE0KMASDL101

C1531 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103

C1532 ELECTROLYTIC CAP. 22µF/6.3V M H7 CE0KMASSL220

C1535 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103

C1536 ELECTROLYTIC CAP. 22µF/6.3V M H7 CE0KMASSL220

C1537 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104

CONNECTORSCN101 242 SERIES CONNECTOR 224202118W1 J322C18TG001

Ref. No. Description Part No.

20060914 1-20-3 E9AB1EL

CN102 PH CONNECTOR TOP 2P B2B-PH-K-S (LF)(SN)

J3PHC02JG029

CN1609 FE CONNECTOR TOP 8P 08FE-BT-VK-N JCFEJ08JG001

DIODESD052 ZENER DIODE MTZJT-7710B QDTB00MTZJ10

D082 PCB JUMPER D0.6-P10.0 JW10.0T

D083 ZENER DIODE MTZJT-7718B QDTB00MTZJ18

D085 RECTIFIER DIODE 1N4005 NDQZ001N4005

D100 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133

D101 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133

D106 ZENER DIODE DZ-4.3BSCT265 NDTC0DZ4R3BS

D108 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133

D109 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133

D112 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133

D221 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133

D223 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133

D501 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133

D502 LED(GREEN) 204-10GD/S957 NPQZ10GDS957

D555 LED MIE-534A2 NPZZM1E534A2

D562 LED(GREEN) 204-10GD/S957 NPQZ10GDS957

D563 LED(GREEN) 204-10GD/S957 NPQZ10GDS957

D565 LED(RED) 204HD/E NPQZ00204HDE

D566 LED(RED) 204HD/E NPQZ00204HDE

D577 LED(RED) 204HD/E NPQZ00204HDE

D701 ZENER DIODE MTZJT-7733D QDTD00MTZJ33

D801 ZENER DIODE MTZJT-775.1B QDTB0MTZJ5R1

D802 ZENER DIODE MTZJT-775.1B QDTB0MTZJ5R1

D805 ZENER DIODE MTZJT-775.1B QDTB0MTZJ5R1

D806 ZENER DIODE MTZJT-775.1B QDTB0MTZJ5R1

D807 ZENER DIODE MTZJT-775.1B QDTB0MTZJ5R1

D808 ZENER DIODE MTZJT-775.1B QDTB0MTZJ5R1

D1603 RECTIFIER DIODE 1N4005 NDQZ001N4005

D1604 RECTIFIER DIODE 1N4005 NDQZ001N4005

ICSIC301 IC Y/C/A LA71205M-MPB-E QSZBA0RSY037

IC451 IC HIFI LA72670BM-MPB-E QSZBA0RSY039

IC501 IC PROCESSOR MN101D10FYD QSZAA0RMS049

IC800 IC SWITCHING CD4052BNSR NSZBA0TTY091

IC803 IC OP AMP UTC4580 DIP-8 8PIN NSZBA0S2H003

IC804 IC OP AMP KIA4558P/P NSZBA0SJY035

IC805 VIDEO SWITCH MM1697AJBE QSZBA0TMM150

IC900 IC MTS DECORDER AN5832SA-E1V QSZBA0TMS003

IC1404 DRIVER FOR DVD MM1636XWRE QSZBA0TMM108

IC1405 DRIVER FOR DVD MM1637XVBE QSZBA0TMM102

IC1406 IC ANALOG MULTIPLEXER CD4053BNSR NSZBA0TTY093

IC1503 VOLTAGE REGULATOR PQ070XF01SZH QSZBA0SSH054

IC1504 VOLTAGE REGULATOR PQ070XF01SZH QSZBA0SSH054

COILSL200 INDUCTOR(100µH K) LAP02TA101K LLAXKATTU101

L251 PCB JUMPER D0.6-P5.0 JW5.0T

L303 INDUCTOR(100µH K) LAP02TA101K LLAXKATTU101

L304 RADIAL TYPE CHOKE COIL CW68-470K-841040NP

LLBD00PKV023

L421 INDUCTOR 47µH-K-5FT LLARKBSTU470

L422 INDUCTOR 22µH-K-26T LLAXKATTU220

L423 PCB JUMPER D0.6-P5.0 JW5.0T

L451 PCB JUMPER D0.6-P5.0 JW5.0T

L501 INDUCTOR(100µH K) LAP02TA101K LLAXKATTU101

L502 RADIAL TYPE CHOKE COIL CW68-470K-841040NP

LLBD00PKV023

L503 INDUCTOR 12µH-K-26T LLAXKATTU120

L505 INDUCTOR(100µH K) LAP02TA101K LLAXKATTU101

L771 PCB JUMPER D0.6-P5.0 JW5.0T

Ref. No. Description Part No.

L800 PCB JUMPER D0.6-P5.0 JW5.0T

L801 PCB JUMPER D0.6-P5.0 JW5.0T

L900 PCB JUMPER D0.6-P5.0 JW5.0T

L901A RADIAL TYPE CHOKE COIL CW68-470K-841040NP

LLBD00PKV023

L1351 INDUCTOR(0.47µH K) LAP02TAR47K LLAXKATTUR47

L1441 CHIP RES.(1608) 1/10W 0 Ω RRXAJR5Z0000

L1461 CHIP RES.(1608) 1/10W 0 Ω RRXAJR5Z0000

L1481 CHIP RES.(1608) 1/10W 0 Ω RRXAJR5Z0000

L1522 RADIAL TYPE CHOKE COIL CW68-470K-841040NP

LLBD00PKV023

TRANSISTORSQ052 NPN TRANSISTOR KRC103M-AT/P NQSZKRC103MP

Q055 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P

Q056 TRANSISTOR KTC3203-Y-AT/P NQSYKTC3203P

Q057 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P

Q101 TRANSISTOR 2SC3266-GR(TPE2 F) QQS12SC3266F

Q102 TRANSISTOR KTA1266-Y-AT/P NQSYKTA1266P

Q103 TRANSISTOR KTC3199-Y-AT/P NQSYKTC3199P

Q104 TRANSISTOR KTA1267-Y-AT/P NQSYKTA1267P

Q105 TRANSISTOR KTC3199-Y-AT/P NQSYKTC3199P

Q107 TRANSISTOR KTA1267-Y-AT/P NQSYKTA1267P

Q108 NPN TRANSISTOR KRC103M-AT/P NQSZKRC103MP

Q205 NPN TRANSISTOR KRC103M-AT/P NQSZKRC103MP

Q301 TRANSISTOR KTA1266-Y-AT/P NQSYKTA1266P

Q302 TRANSISTOR KTC3193-Y-AT/P NQSYKTC3193P

Q303 TRANSISTOR KTC3193-Y-AT/P NQSYKTC3193P

Q391 TRANSISTOR KTA1266-Y-AT/P NQSYKTA1266P

Q421 TRANSISTOR KTA1266-Y-AT/P NQSYKTA1266P

Q422 TRANSISTOR KTC3203-Y-AT/P NQSYKTC3203P

Q425 RES. BUILT-IN TRANSISTOR KRA103M-AT/P NQSZ0KRA103M

Q426 CHIP TRANSISTOR RN1511(TE85R.F) QQ2Z0RN1511F

Q501 TRANSISTOR KTC3199-BL-AT/P NQS5KTC3199P

Q506 PHOTO TRANSISTOR PT204-6B-12 NPWZT2046B12

Q509 NPN TRANSISTOR KRC103M-AT/P NQSZKRC103MP

Q510 TRANSISTOR KTC3199-Y-AT/P NQSYKTC3199P

Q511 TRANSISTOR KTC3199-Y-AT/P NQSYKTC3199P

Q512 TRANSISTOR KTC3199-Y-AT/P NQSYKTC3199P

Q513 TRANSISTOR KTC3199-Y-AT/P NQSYKTC3199P

Q514 TRANSISTOR KTC3199-Y-AT/P NQSYKTC3199P

Q804 TRANSISTOR KTA1266-Y-AT/P NQSYKTA1266P

Q805 TRANSISTOR KTC3199-Y-AT/P NQSYKTC3199P

Q806 TRANSISTOR KTC3199-Y-AT/P NQSYKTC3199P

Q1303 TRANSISTOR KTC3199-BL-AT/P NQS5KTC3199P

Q1304 TRANSISTOR KTC3199-BL-AT/P NQS5KTC3199P

Q1305 TRANSISTOR KTA1267-Y-AT/P NQSYKTA1267P

Q1351 TRANSISTOR KTC3199-Y-AT/P NQSYKTC3199P

RESISTORSR056 CARBON RES. 1/4W J 1k Ω RCX4JATZ0102

R057 CARBON RES. 1/6W J 150 Ω RCX6JATZ0151

R064 CARBON RES. 1/6W G 1.5k Ω RCX6GATZ0152

R065 CARBON RES. 1/6W G 820 Ω RCX6GATZ0821

R073 CARBON RES. 1/4W J 10k Ω RCX4JATZ0103

R075 CARBON RES. 1/6W J 4.7k Ω RCX6JATZ0472

R092 CARBON RES. 1/4W J 8.2k Ω RCX4JATZ0822

R095 CARBON RES. 1/4W J 8.2k Ω RCX4JATZ0822

R097 CARBON RES. 1/6W J 47k Ω RCX6JATZ0473

R103 CHIP RES. 1/10W J 22k Ω RRXAJR5Z0223

R104 CARBON RES. 1/6W J 47k Ω RCX6JATZ0473

R106 CARBON RES. 1/4W J 5.6k Ω RCX4JATZ0562

R115 CARBON RES. 1/4W J 470 Ω RCX4JATZ0471

R116 CHIP RES. 1/10W J 4.7k Ω RRXAJR5Z0472

R117 CHIP RES. 1/10W J 4.7k Ω RRXAJR5Z0472

Ref. No. Description Part No.

20060914 1-20-4 E9AB1EL

R118 CHIP RES. 1/10W J 47k Ω RRXAJR5Z0473

R125 CARBON RES. 1/4W J 220 Ω RCX4JATZ0221

R126 CHIP RES. 1/10W J 47k Ω RRXAJR5Z0473

R127 CHIP RES. 1/10W J 5.6k Ω RRXAJR5Z0562

R132 CARBON RES. RD1/2S101JTA RCX2JATZ0101

R133 CARBON RES. 1/4W J 220 Ω RCX4JATZ0221

R221 CHIP RES. 1/10W J 2.2k Ω RRXAJR5Z0222

R222 CHIP RES.(1608) 1/10W F 10k Ω RRXAFR5H0103

R223 CHIP RES.(1608) 1/10W F 1.5k Ω RRXAFR5H0152

R224 CHIP RES. 1/10W F 15k Ω RRXAFR5H0153

R225 CHIP RES. 1/10W J 47k Ω RRXAJR5Z0473

R226 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103

R228 CHIP RES. 1/10W J 2.7k Ω RRXAJR5Z0272

R229 CHIP RES. 1/10W J 2.2k Ω RRXAJR5Z0222

R230 CHIP RES.(1608) 1/10W F 10k Ω RRXAFR5H0103

R231 CHIP RES.(1608) 1/10W F 120 Ω RRXAFR5H0121

R232 CHIP RES.(1608) 1/10W F 10k Ω RRXAFR5H0103

R234 CHIP RES. 1/10W J 47k Ω RRXAJR5Z0473

R235 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103

R301 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103

R302 CHIP RES. 1/10W J 12k Ω RRXAJR5Z0123

R304 CHIP RES. 1/10W J 1.2k Ω RRXAJR5Z0122

R306 CHIP RES. 1/10W J 3.9M Ω RRXAJR5Z0395

R307 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104

R308 CHIP RES. 1/10W J 82k Ω RRXAJR5Z0823

R309 CHIP RES. 1/10W J 2.2k Ω RRXAJR5Z0222

R310 CHIP RES. 1/10W J 4.7k Ω RRXAJR5Z0472

R311 CHIP RES. 1/10W J 1.8k Ω RRXAJR5Z0182

R312 CHIP RES. 1/10W J 1.8k Ω RRXAJR5Z0182

R313 CHIP RES. 1/10W J 1.8k Ω RRXAJR5Z0182

R314 CHIP RES. 1/10W J 680k Ω RRXAJR5Z0684

R316 CHIP RES. 1/10W J 2.2k Ω RRXAJR5Z0222

R317 CHIP RES. 1/10W J 8.2k Ω RRXAJR5Z0822

R321 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103

R322 CHIP RES. 1/10W J 18k Ω RRXAJR5Z0183

R323 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103

R324 CHIP RES. 1/10W J 18k Ω RRXAJR5Z0183

R327 CHIP RES.(1608) 1/10W F 1.1k Ω RRXAFR5H0112

R391 CARBON RES. 1/4W J 560 Ω RCX4JATZ0561

R392 CARBON RES. 1/4W J 560 Ω RCX4JATZ0561

R395 PCB JUMPER D0.6-P5.0 JW5.0T

R397 CHIP RES. 1/10W J 220 Ω RRXAJR5Z0221

R401 CHIP RES. 1/10W J 6.8k Ω RRXAJR5Z0682

R402 CHIP RES. 1/10W J 5.6k Ω RRXAJR5Z0562

R409 CHIP RES. 1/10W J 8.2k Ω RRXAJR5Z0822

R410 CHIP RES. 1/10W J 12k Ω RRXAJR5Z0123

R411 CHIP RES. 1/10W J 330k Ω RRXAJR5Z0334

R412 CHIP RES. 1/10W J 150 Ω RRXAJR5Z0151

R413 CHIP RES. 1/10W J 18k Ω RRXAJR5Z0183

R414 CHIP RES. 1/10W J 910 Ω RRXAJR5Z0911

R415 CHIP RES. 1/10W J 2.2k Ω RRXAJR5Z0222

R421 CHIP RES. 1/10W J 1k Ω RRXAJR5Z0102

R422 CHIP RES. 1/10W J 22k Ω RRXAJR5Z0223

R424 CARBON RES. 1/6W J 47k Ω RCX6JATZ0473

R425 CARBON RES. 1/6W J 100 Ω RCX6JATZ0101

R426 CARBON RES. 1/6W J 820 Ω RCX6JATZ0821

R451 CHIP RES. 1/10W J 12k Ω RRXAJR5Z0123

R452 CHIP RES. 1/10W J 4.7k Ω RRXAJR5Z0472

R453 CHIP RES. 1/10W J 27k Ω RRXAJR5Z0273

R454 CHIP RES. 1/10W J 22k Ω RRXAJR5Z0223

R455 CHIP RES. 1/10W J 47k Ω RRXAJR5Z0473

R456 CHIP RES. 1/10W J 6.8k Ω RRXAJR5Z0682

R457 CHIP RES. 1/10W J 470 Ω RRXAJR5Z0471

Ref. No. Description Part No.

R458 CHIP RES. 1/10W J 3.3k Ω RRXAJR5Z0332

R459 CHIP RES. 1/10W J 39k Ω RRXAJR5Z0393

R463 CHIP RES. 1/10W J 27k Ω RRXAJR5Z0273

R464 CHIP RES. 1/10W J 22k Ω RRXAJR5Z0223

R465 CHIP RES. 1/10W J 47k Ω RRXAJR5Z0473

R466 CHIP RES. 1/10W J 6.8k Ω RRXAJR5Z0682

R468 CHIP RES. 1/10W J 470 Ω RRXAJR5Z0471

R469 CHIP RES. 1/10W J 1k Ω RRXAJR5Z0102

R470 CHIP RES. 1/10W J 470 Ω RRXAJR5Z0471

R471 CHIP RES. 1/10W J 1k Ω RRXAJR5Z0102

R484 CHIP RES. 1/10W J 47k Ω RRXAJR5Z0473

R485 CHIP RES. 1/10W J 15k Ω RRXAJR5Z0153

R486 CHIP RES. 1/10W J 47k Ω RRXAJR5Z0473

R487 CHIP RES. 1/10W J 15k Ω RRXAJR5Z0153

R502 CHIP RES. 1/10W J 2.2k Ω RRXAJR5Z0222

R503 CHIP RES. 1/10W J 820 Ω RRXAJR5Z0821

R504 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104

R505 CHIP RES. 1/10W F 3.9k Ω RRXAFR5H3901

R506 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104

R508 CHIP RES.(1608) 1/10W 0 Ω RRXAJR5Z0000

R510 CARBON RES. 1/6W J 150 Ω RCX6JATZ0151

R511 CHIP RES. 1/10W J 39k Ω RRXAJR5Z0393

R516 CHIP RES.(1608) 1/10W 0 Ω RRXAJR5Z0000

R517 CARBON RES. 1/6W J 10k Ω RCX6JATZ0103

R518 CHIP RES. 1/10W J 220k Ω RRXAJR5Z0224

R521 CHIP RES. 1/10W J 1k Ω RRXAJR5Z0102

R523 CHIP RES. 1/10W J 2.2k Ω RRXAJR5Z0222

R524 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103

R525 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103

R526 CHIP RES. 1/10W J 1k Ω RRXAJR5Z0102

R527 CHIP RES. 1/10W J 1k Ω RRXAJR5Z0102

R528 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103

R529 CHIP RES.(1608) 1/10W 0 Ω RRXAJR5Z0000

R531 CHIP RES.(1608) 1/10W F 4.7k Ω RRXAFR5H0472

R532 CHIP RES.(1608) 1/10W F 1.5k Ω RRXAFR5H0152

R533 CHIP RES.(1608) 1/10W F 22k Ω RRXAFR5H0223

R534 CHIP RES. 1/10W F 470 Ω RRXAFR5H0471

R535 CHIP RES.(1608) 1/10W F 10k Ω RRXAFR5H0103

R536 CHIP RES.(1608) 1/10W F 3.6k Ω RRXAFR5H0362

R537 CHIP RES. 1/10W J 33k Ω RRXAJR5Z0333

R540 CHIP RES. 1/10W J 390k Ω RRXAJR5Z0394

R541 CHIP RES. 1/10W J 390k Ω RRXAJR5Z0394

R542 CARBON RES. 1/4W J 220 Ω RCX4JATZ0221

R543 CHIP RES. 1/10W J 4.7k Ω RRXAJR5Z0472

R544 CHIP RES. 1/10W J 18k Ω RRXAJR5Z0183

R545 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103

R546 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103

R547 CARBON RES. 1/6W J 1k Ω RCX6JATZ0102

R548 CHIP RES. 1/10W J 4.7k Ω RRXAJR5Z0472

R551 CHIP RES. 1/10W J 6.8k Ω RRXAJR5Z0682

R556 CARBON RES. 1/6W J 47k Ω RCX6JATZ0473

R559 CHIP RES. 1/10W J 3.9k Ω RRXAJR5Z0392

R560 CHIP RES. 1/10W F 3.9k Ω RRXAFR5H3901

R561 CHIP RES. 1/10W F 3.9k Ω RRXAFR5H3901

R562 CARBON RES. 1/6W J 150 Ω RCX6JATZ0151

R563 CHIP RES. 1/10W F 3.9k Ω RRXAFR5H3901

R564 CARBON RES. 1/6W J 150 Ω RCX6JATZ0151

R566 CARBON RES. 1/6W J 150 Ω RCX6JATZ0151

R567 CARBON RES. 1/6W J 150 Ω RCX6JATZ0151

R569 CARBON RES. 1/6W J 150 Ω RCX6JATZ0151

R570 CARBON RES. 1/6W J 150 Ω RCX6JATZ0151

R601 CHIP RES. 1/10W J 1.8k Ω RRXAJR5Z0182

R602 CHIP RES. 1/10W J 1k Ω RRXAJR5Z0102

Ref. No. Description Part No.

20060914 1-20-5 E9AB1EL

R603 CHIP RES. 1/10W J 1.2k Ω RRXAJR5Z0122

R604 CHIP RES. 1/10W J 1.5k Ω RRXAJR5Z0152

R605 CHIP RES. 1/10W J 2.2k Ω RRXAJR5Z0222

R606 CHIP RES. 1/10W J 3.9k Ω RRXAJR5Z0392

R607 CHIP RES. 1/10W J 8.2k Ω RRXAJR5Z0822

R608 CHIP RES. 1/10W J 22k Ω RRXAJR5Z0223

R611 CHIP RES. 1/10W J 1.8k Ω RRXAJR5Z0182

R612 CHIP RES. 1/10W J 1k Ω RRXAJR5Z0102

R613 CHIP RES. 1/10W J 1.2k Ω RRXAJR5Z0122

R614 CHIP RES. 1/10W J 1.5k Ω RRXAJR5Z0152

R615 CHIP RES. 1/10W J 2.2k Ω RRXAJR5Z0222

R616 CHIP RES. 1/10W J 3.9k Ω RRXAJR5Z0392

R617 CHIP RES. 1/10W J 8.2k Ω RRXAJR5Z0822

R618 CHIP RES. 1/10W J 22k Ω RRXAJR5Z0223

R641 CHIP RES. 1/10W J 3.3k Ω RRXAJR5Z0332

R642 CHIP RES. 1/10W J 3.3k Ω RRXAJR5Z0332

R645 CHIP RES. 1/10W J 2.2k Ω RRXAJR5Z0222

R646 CHIP RES. 1/10W J 3.3k Ω RRXAJR5Z0332

R647 CHIP RES. 1/10W J 2.2k Ω RRXAJR5Z0222

R648 CHIP RES. 1/10W J 3.3k Ω RRXAJR5Z0332

R650 CHIP RES. 1/10W J 1k Ω RRXAJR5Z0102

R651 CHIP RES. 1/10W J 560 Ω RRXAJR5Z0561

R702 CARBON RES. 1/4W J 1.8k Ω RCX4JATZ0182

R751 CHIP RES. 1/10W J 75 Ω RRXAJR5Z0750

R777 CARBON RES. 1/6W J 39k Ω RCX6JATZ0393

R778 CARBON RES. 1/6W J 10k Ω RCX6JATZ0103

R806 CHIP RES. 1/10W J 33k Ω RRXAJR5Z0333

R807 CHIP RES. 1/10W J 15k Ω RRXAJR5Z0153

R808 CHIP RES. 1/10W J 15k Ω RRXAJR5Z0153

R809 CHIP RES. 1/10W J 33k Ω RRXAJR5Z0333

R810 CHIP RES. 1/10W J 75 Ω RRXAJR5Z0750

R825 CHIP RES. 1/10W J 15k Ω RRXAJR5Z0153

R826 CHIP RES. 1/10W J 33k Ω RRXAJR5Z0333

R827 CHIP RES. 1/10W J 15k Ω RRXAJR5Z0153

R828 CHIP RES. 1/10W J 33k Ω RRXAJR5Z0333

R829 CHIP RES. 1/10W J 15k Ω RRXAJR5Z0153

R830 CHIP RES. 1/10W J 33k Ω RRXAJR5Z0333

R831 CHIP RES. 1/10W J 15k Ω RRXAJR5Z0153

R832 CHIP RES. 1/10W J 33k Ω RRXAJR5Z0333

R833 CARBON RES. 1/6W J 18k Ω RCX6JATZ0183

R834 CHIP RES. 1/10W J 27k Ω RRXAJR5Z0273

R835 CHIP RES. 1/10W J 18k Ω RRXAJR5Z0183

R836 CHIP RES. 1/10W J 27k Ω RRXAJR5Z0273

R837 CHIP RES.(1608) 1/10W F 10k Ω RRXAFR5H0103

R838 CHIP RES. 1/10W J 6.8k Ω RRXAJR5Z0682

R839 CHIP RES. 1/10W J 6.8k Ω RRXAJR5Z0682

R840 CHIP RES.(1608) 1/10W F 10k Ω RRXAFR5H0103

R841 CHIP RES. 1/10W F 18k Ω RRXAFR5H0183

R843 CHIP RES. 1/10W F 18k Ω RRXAFR5H0183

R847 CHIP RES. 1/10W J 1k Ω RRXAJR5Z0102

R852 CHIP RES. 1/10W F 7.5k Ω RRXAFR5H0752

R853 CHIP RES.(1608) 1/10W F 4.7k Ω RRXAFR5H0472

R854 CHIP RES.(1608) 1/10W F 12k Ω RRXAFR5H0123

R855 CHIP RES. 1/10W F 7.5k Ω RRXAFR5H0752

R856 CHIP RES.(1608) 1/10W F 4.7k Ω RRXAFR5H0472

R857 CHIP RES.(1608) 1/10W F 12k Ω RRXAFR5H0123

R858 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104

R859 CHIP RES. 1/10W J 470 Ω RRXAJR5Z0471

R860 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104

R861 CHIP RES. 1/10W J 470 Ω RRXAJR5Z0471

R862 CHIP RES. 1/10W J 22k Ω RRXAJR5Z0223

R863 CARBON RES. 1/6W J 22k Ω RCX6JATZ0223

R867 CHIP RES. 1/10W J 1.5k Ω RRXAJR5Z0152

Ref. No. Description Part No.

R868 CHIP RES. 1/10W J 1.5k Ω RRXAJR5Z0152

R871 CHIP RES. 1/10W J 220 Ω RRXAJR5Z0221

R872 CHIP RES. 1/10W J 220 Ω RRXAJR5Z0221

R875 CHIP RES. 1/10W J 4.7k Ω RRXAJR5Z0472

R876 CHIP RES. 1/10W J 4.7k Ω RRXAJR5Z0472

R900 CHIP RES.(1608) 1/10W 0 Ω RRXAJR5Z0000

R902 CHIP RES. 1/10W J 180k Ω RRXAJR5Z0184

R907 CHIP RES. 1/10W J 3.3k Ω RRXAJR5Z0332

R908 CHIP RES. 1/10W J 100 Ω RRXAJR5Z0101

R909 CHIP RES. 1/10W J 100 Ω RRXAJR5Z0101

R910 CHIP RES. 1/10W J 220 Ω RRXAJR5Z0221

R911 CHIP RES. 1/10W J 220 Ω RRXAJR5Z0221

R912 CHIP RES. 1/10W J 330 Ω RRXAJR5Z0331

R914 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103

R1327 CHIP RES. 1/10W J 470 Ω RRXAJR5Z0471

R1329 CHIP RES. 1/10W J 1.5k Ω RRXAJR5Z0152

R1331 CHIP RES. 1/10W J 1k Ω RRXAJR5Z0102

R1332 CHIP RES. 1/10W J 1k Ω RRXAJR5Z0102

R1333 CHIP RES. 1/10W J 910 Ω RRXAJR5Z0911

R1334 CHIP RES. 1/10W J 470 Ω RRXAJR5Z0471

R1335 CHIP RES. 1/10W J 820 Ω RRXAJR5Z0821

R1351 CHIP RES. 1/10W J 1.8k Ω RRXAJR5Z0182

R1352 CHIP RES. 1/10W J 2.2k Ω RRXAJR5Z0222

R1353 CHIP RES. 1/10W J 2.2k Ω RRXAJR5Z0222

R1354 CHIP RES. 1/10W J 220 Ω RRXAJR5Z0221

R1355 CHIP RES. 1/10W J 75 Ω RRXAJR5Z0750

R1356 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104

R1402 CHIP RES. 1/10W J 75 Ω RRXAJR5Z0750

R1403 CHIP RES. 1/10W J 75 Ω RRXAJR5Z0750

R1404 CHIP RES. 1/10W J 75 Ω RRXAJR5Z0750

R1407 CHIP RES. 1/10W J 75 Ω RRXAJR5Z0750

R1409 CHIP RES.(1608) 1/10W F 220 Ω RRXAFR5H0221

R1410 CHIP RES.(1608) 1/10W F 3.3k Ω RRXAFR5H0332

R1421 CHIP RES.(1608) 1/10W F 240 Ω RRXAFR5H0241

R1422 CHIP RES.(1608) 1/10W F 4.7k Ω RRXAFR5H0472

R1441 CHIP RES.(1608) 1/10W F 200 Ω RRXAFR5H0201

R1443 CHIP RES. 1/10W J 75 Ω RRXAJR5Z0750

R1461 CHIP RES.(1608) 1/10W F 220 Ω RRXAFR5H0221

R1462 CHIP RES. 1/10W J 75 Ω RRXAJR5Z0750

R1481 CHIP RES.(1608) 1/10W F 220 Ω RRXAFR5H0221

R1482 CHIP RES. 1/10W J 75 Ω RRXAJR5Z0750

R1521 CHIP RES. 1/10W J 2.2k Ω RRXAJR5Z0222

R1615 CARBON RES. 1/6W J 1.2k Ω RCX6JATZ0122

R1616 CHIP RES. 1/10W J 33k Ω RRXAJR5Z0333

R1617 CARBON RES. 1/6W J 100 Ω RCX6JATZ0101

SWITCHESSW511 LEAF SWITCH MXS01830MVP0 SSC0101MCE03

SW512 ROTARY MODE SWITCH SSS-53MD SSR0106KB003

SW602 TACT SWITCH KSM0614B SST0101HH013

SW603 TACT SWITCH KSM0614B SST0101HH013

SW604 TACT SWITCH KSM0614B SST0101HH013

SW605 TACT SWITCH KSM0614B SST0101HH013

SW606 TACT SWITCH KSM0614B SST0101HH013

SW607 TACT SWITCH KSM0614B SST0101HH013

SW608 TACT SWITCH KSM0614B SST0101HH013

SW609 TACT SWITCH KSM0614B SST0101HH013

SW611 TACT SWITCH KSM0614B SST0101HH013

SW613 TACT SWITCH KSM0614B SST0101HH013

SW616 TACT SWITCH KSM0614B SST0101HH013

MISCELLANEOUS2B16 BUSH LED(F) H3700UD 0VM409508

2B17 SHIELD ASSEMBLY H9200UD 0VM413279A

Ref. No. Description Part No.

20060914 1-20-6 E9AB1EL

POWER SW CBA

DVD OPEN/CLOSE SW CBA

FRONT JACK CBA

SENSOR CBA

PSV CBA

POWER SUPPLY CBA

JC2 CHIP RES.(1608) 1/10W 0 Ω RRXAJR5Z0000

JC5 CHIP RES.(1608) 1/10W 0 Ω RRXAJR5Z0000

JC6 CHIP RES.(1608) 1/10W 0 Ω RRXAJR5Z0000

JC31 CHIP RES.(1608) 1/10W 0 Ω RRXAJR5Z0000

JC38 CHIP RES.(1608) 1/10W 0 Ω RRXAJR5Z0000

JK751 RCA JACK MSP-213V1-324-B NI L JXRL030LY104

JK804 RCA JACK MSP-213V3-324-B NI L JYRL030LY025

JK805 RCA JACK MSP-382V-12 NILF JXRL020LY120

JK1202 RCA JACK MSP-281V41-B(B110) JXRL010LY140

JK1401 S TYPE JACK MDC-050V-2.4 LF(B110 JXEL040LY003

JK1402 S TYPE JACK MDC-050V-2.4 LF(B110 JXEL040LY003

JK1403 RCA JACK MSP-213V1-652-B NI L JXRL030LY116

RS501 SENSOR REMOTE RECEIVER KSM-602LU2S USESJRSKK048

TP301 PCB JUMPER D0.6-P7.5 JW7.5T

TP302 PCB JUMPER D0.6-P15.0 JW15.0T

TP452 PCB JUMPER D0.6-P30.0 JW30.0T

TP502 PCB JUMPER D0.6-P7.5 JW7.5T

TP505 PCB JUMPER D0.6-P10.0 JW10.0T

TP506 PCB JUMPER D0.6-P5.0 JW5.0T

TP507 PCB JUMPER D0.6-P13.5 JW13.5T

TP513 PCB JUMPER D0.6-P5.0 JW5.0T

TP751 PCB JUMPER D0.6-P6.0 JW6.0T

TP753 PCB JUMPER D0.6-P6.0 JW6.0T

TP754 PCB JUMPER D0.6-P6.0 JW6.0T

TU900 TUNER UNIT VH025AFE UTUNNTUSP026

VR501 CARBON P.O.T. VZ067TL1 B104 PB(F) VRCB104HH014

W01 WIRE ASSEMBLY FFC 30PIN 30PIN/P1.00/140 WX1E9A00-001

W02 WIRE ASSEMBLY FFC 30PIN 30PIN/P1.00/140 WX1E9A00-001

X301 XTAL 3.579545MHz(20PPM) FXC355LLN004

X502 RESONATOR XTAL 32.768kHz QTF38-32.768K125P15L

FXC323LQUA03

Ref. No. Description Part No.

POWER SW CBA (MCV-B)Consists of the following:

----------

DIODED561 LED(RED) 204HD/E NPQZ00204HDE

SWITCHSW601 TACT SWITCH KSM0614B SST0101HH013

MISCELLANEOUSW001 WIRE ASSEMBLY 4P 4PIN/AWG26#2651/P2.0 WX1E9A00-002

Ref. No. Description Part No.

DVD OPEN/CLOSE SW CBA (MCV-C)Consists of the following:

----------

SWITCHESSW615 TACT SWITCH KSM0614B SST0101HH013

SW617 TACT SWITCH KSM0614B SST0101HH013

MISCELLANEOUSW002 WIRE ASSEMBLY 3PIN 3PIN/AWG26#2651/

P2.0WX1E9A00-003

Ref. No. Description Part No.

Ref. No. Description Part No.

FRONT JACK CBA (MCV-D)Consists of the following:

----------

CONNECTORCN1605 FE CONNECTOR TOP 8P 08FE-BT-VK-N JCFEJ08JG001

RESISTORSR804 CHIP RES. 1/10W J 75 Ω RRXAJR5Z0750

R812 CHIP RES. 1/10W J 75 Ω RRXAJR5Z0750

R815 CHIP RES. 1/10W J 75 Ω RRXAJR5Z0750

MISCELLANEOUSJK800 RCA JACK(RED) MTJ-032-11A-31 FE01 JYRL010LY024

JK801 RCA JACK(WHITE) MTJ-032-11B-41 FE01 JXRL010LY102

JK803 RCA JACK(YELLOW) MTJ-032-11B-40 FE01 JXRL010LY101

JK806 S TYPE JACK MDC-050V-2.4 LF(B110 JXEL040LY003

W03 WIRE ASSEMBLY FFC 8PIN FFC_8PIN/105MM/P1.25

WX1E9A00-006

Ref. No. Description Part No.

SENSOR CBAConsists of the following:

1VSA13725

TRANSISTORSQ503 PHOTO TRANSISTOR PT204-6B-12 NPWZT2046B12

Q504 PHOTO TRANSISTOR PT204-6B-12 NPWZT2046B12

Ref. No. Description Part No.

PSV CBAConsists of the following

1VSA14907

POWER SUPPLY CBA (PSV-A)JUNCTION CBA (PSV-B)

--------------------

Ref. No. Description Part No.

POWER SUPPLY CBA (PSV-A)Consists of the following:

----------

CAPACITORSC012 ELECTROLYTIC CAP. 470µF/16V M CE1CMASDL471

C013 ELECTROLYTIC CAP. 10µF/50V M H7 CE1JMASSL100

C014 ELECTROLYTIC CAP. 470µF/16V M CE1CMASDL471

C015 ELECTROLYTIC CAP. 1000µF/16V M CE1CMASDL102

C017 ELECTROLYTIC CAP. 4700µF/6.3V SL CE0KMZADL472

C018 CERAMIC CAP. B K 220pF500V CCD2JKP0B221

C019 ELECTROLYTIC CAP. 1000µF/6.3V M CE0KMASDL102

C021 ELECTROLYTIC CAP. 470µF/6.3V M CE0KMASDL471

C023 CERAMIC CAP. B K 470pF500V CCD2JKP0B471

C024 ELECTROLYTIC CAP. 22µF/50V M CE1JMASDL220

C027 ELECTROLYTIC CAP. 3300µF/6.3V SL CE0KMZADL332

C028 ELECTROLYTIC CAP. 1000µF/6.3V M CE0KMASDL102

C031 CHIP CERAMIC CAP.(1608) B K 0.033µF/50V CHD1JK30B333

C1001# METALIZED FILM CAP. 0.068µF/250V M CT2E683MS037

C1003 CERAMIC CAP. B K 0.01µF/500V CCD2JKP0B103

C1004 ELECTROLYTIC CAP. 220µF/200V M CA2D221S6008

C1005 CERAMIC CAP. B K 220pF500V CCD2JKP0B221

C1006# SAFETY CAP. 3300pF250V CCG2EMA0F332

C1013 CERAMIC CAP.(AX) B K 1000pF50V CCA1JKT0B102

C1029 CERAMIC CAP.(AX) X K 2200pF16V CCA1CKT0X222

C1032 ELECTROLYTIC CAP. 10µF/16V M H7 CE1CMAVSL100

C1033 CERAMIC CAP. F Z 0.022µF/50V CCD1JZS0F223

DIODESD012 SCHOTTKY BARRIER DIODE SB390 NDQZ000SB390

20060914 1-20-7 E9AB1EL

JUNCTION CBA

D013 RECTIFIER DIODE BA158 NDQZ000BA158

D014 SCHOTTKY BARRIER DIODE SB190 NDQZ000SB190

D015 SCHOTTKY BARRIER DIODE SB340 NDQZ000SB340

D016 SCHOTTKY BARRIER DIODE SB340 NDQZ000SB340

D017 ZENER DIODE MTZJT-7715C QDTC00MTZJ15

D018 RECTIFIER DIODE BA158 NDQZ000BA158

D020 PCB JUMPER D0.6-P5.0 JW5.0T

D021 SCHOTTKY BARRIER DIODE SB340 NDQZ000SB340

D022 SCHOTTKY BARRIER DIODE SB140 NDQZ000SB140

D025 ZENER DIODE MTZJT-776.8B QDTB0MTZJ6R8

D1001 DIODE 1N5397-B NDLZ001N5397

D1002 DIODE 1N5397-B NDLZ001N5397

D1003 DIODE 1N5397-B NDLZ001N5397

D1004 DIODE 1N5397-B NDLZ001N5397

D1006 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133

D1007 CARBON RES. 1/4W J 68k Ω RCX4JATZ0683

D1011 RECTIFIER DIODE BA158 NDQZ000BA158

D1012 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133

D1018 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133

D1023 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133

D1024 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133

D1025 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133

ICIC010# PHOTOCOUPLER PS2561A-1(W) QPEWPS2561A1

COILSL010 POWER INDUCTORS TWKBNP-180K LLC180KKV007

L012 POWER INDUCTORS TWKBNP-150K LLC150KKV007

L013 RADIAL TYPE CHOKE COIL CW68-470K-841040NP

LLBD00PKV023

L1001# LINE FILTER 27MH CGS-LF0059A-NP LLBG00ZSA012

L1002 BEAD CORE B16 RH 3.5X10X1.3 XL03010XM001

TRANSISTORSQ031 TRANSISTOR KTA1267-Y-AT/P NQSYKTA1267P

Q1001# MOS FET 2SK3563 QFWZ02SK3563

Q1003 TRANSISTOR KTC3199-Y-AT/P NQSYKTC3199P

Q1008 TRANSISTOR KTC3199-Y-AT/P NQSYKTC3199P

RESISTORSR001# GLASS GLAZE RES. 1/2W J 3.3M Ω RXX2JZLZ0335

R016 CHIP RES. 1/10W J 1k Ω RRXAJR5Z0102

R017 CHIP RES.(1608) 1/10W 0 Ω RRXAJR5Z0000

R018 CHIP RES. 1/10W J 4.7k Ω RRXAJR5Z0472

R019 CHIP RES. 1/10W J 1.8k Ω RRXAJR5Z0182

R020 CHIP RES.(1608) 1/10W 0 Ω RRXAJR5Z0000

R021 CHIP RES.(1608) 1/10W F 2.2k Ω RRXAFR5H0222

R022 CHIP RES. 1/10W F 5.6k Ω RRXAFR5H0562

R023 CHIP RES.(1608) 1/10W 0 Ω RRXAJR5Z0000

R1004 METAL OXIDE FILM RES. 2W J 82k Ω RN02823ZU001

R1005 CARBON RES. 1/4W J 1M Ω RCX4JATZ0105

R1006 CARBON RES. 1/4W J 1M Ω RCX4JATZ0105

R1008 CARBON RES. 1/6W G 680 Ω RCX6GATZ0681

R1010 CARBON RES. 1/6W J 22k Ω RCX6JATZ0223

R1011 METAL OXIDE FILM RES. 2W J 0.68 Ω RN02R68ZU001

R1029 CARBON RES. 1/6W J 150k Ω RCX6JATZ0154

R1032 CARBON RES. 1/6W G 1.2k Ω RCX6GATZ0122

R1034 CARBON RES. 1/4W J 680k Ω RCX4JATZ0684

R1036 CARBON RES. 1/6W J 100k Ω RCX6JATZ0104

R1037 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103

R1038 CARBON RES. 1/6W J 100k Ω RCX6JATZ0104

R1039 CARBON RES. 1/6W J 470k Ω RCX6JATZ0474

R1043 METAL OXIDE FILM RES. 2W J 1.8 Ω RN021R8ZU001

R1044 CARBON RES. 1/4W J 1k Ω RCX4JATZ0102

MISCELLANEOUS

Ref. No. Description Part No.

2B18 HEATSINK V2600PZ 0VM409007B

2L019 SCREW S-TIGHT M3X8 BIND HEAD+ GBJS3080

AC1001# AC CORD W/O A GND WIRE UL/CSA 1770 BLACK

WAC0172LTE17

F1001# FUSE TIME RAG SIC 1A 250V UC PSE PEG20C0W3002

FH1001 FUSE HOLDER MSF-015 LF (B110) XH01Z00LY002

FH1002 FUSE HOLDER MSF-015 LF (B110) XH01Z00LY002

T001# TRANS POWER BCK-28-0663 LTT00CPXB033

Ref. No. Description Part No.

JUNCTION CBA (PSV-B)Consists of the following:

----------

CONNECTORCN1612 242 SERIES CONNECTOR TUC-P18X-B1 WHT

STJCTUB18TG002

DIODED2013 RECTIFIER DIODE RL201 NDQZ000RL201

MISCELLANEOUSW003 WIRE ASSEMBLY 9P 9PIN/AWG26#2651/P2.0 WX1E9A00-004

W004 WIRE ASSEMBLY 9P 9PIN/AWG26#2651/P2.0 WX1E9A00-004

Ref. No. Description Part No.

CWV20V6E9AB1CD2006-10-6