service manual - cowaycoway.ir/upload/manual/service manual/ba-08 svc manual(100203).pdf · 3...

BA08-AR/AEService Manual

C o w a y T e c h n o l o g y

Bidet

1

CONTENTS

1. Important safeguards

2-1. Specification2-2. Structure and name2-3. Dimensions and appearance2-4. Remote control functions2-5. Remote control display2-6. Description of the keys in the main body2-7. Features

0708

02

0911121214

2. Product description

33

34

35

3536

6-1. Cautions during disassembly and assembly6-2. Needed tools6-3. Disassembly method for each part6-4. Diagram of disassembly 42

44

46

47

48

50

60

6. Disassembly and assembly

7. Signs of failure and way to repair

8. Error indication Mode (LED)

9. Electrical wiring

10. Description summary of PCB Connector

11. List of A/S component

12. Ddo Ddo service

3-1. Installation materials3-2. Procedures

1819

23

3. Installation

5-1. Basic configuration5-2. Main functions5-3. Function setting manual(main device)5-4. Amount of water output for levels during

Rear/Front cleansing5-5. Power consumption (Electricity cost)5-6. Resistance and voltage values for various

temperatures on temperature sensor

242527

33

5. Operating principles

4. Preparation and checklist before use

2

1. IMPORTANT SAFEGUARDS

Do not pull the power cord toostrong.- Otherwise, electrical hazard,

short circuit, or a fire can occurfrom the cord damage.

Do not use the damaged cord andloosen outlet.- Otherwise, It might cause the electrical

hazard or a fire.

If the power plug has unknownsubstance or water on it, pleaseuse it after wipe them away.- Otherwise, improper contact might

cause fire.

Do not use multiple plugs onone outlet.- Otherwise, it may cause the

overheating or a fire.

Do not pull out and pull in withwet hands.- Otherwise, it may cause electrical

hazard.

Do not use the product in excessivelyhumid place nor shower it with water.- Otherwise, it may cause the electrical

hazard or a fire.

▶ ▶

▶ ▶

▶ ▶

3

During shower or cleaningwith water, please be awarenot to put water or detergenton product or power plug.- Otherwise, it may cause the electrical

hazard or a fire.- If the unknown substances or

water are penetrated into the product, do not pull the plug. Close the inputvalve on T-shaped connector,and call A/S center.

Please pull out the power plugduring cleaning.- Otherwise, electrical hazard may happen.

Do not use the product in failedstate, and call A/S center.- Otherwise, it may cause the electrical

hazard or a fire.- Pull out the power plug immediately,

and close the input valve on T-shapedconnector. Then, call A/S center.

Do not disassemble, repair, ormodify the product.- Otherwise, it may cause the

electrical hazard or a fire.- Do not disassemble or repair by

yourself, call A/S for our expert.

Do not separate the main body,seat and seat cover.- High voltage is running inside, so

it may cause the electrical hazard.- Seat lid is easy to separate.

So clean it after the separating itfrom the seat.

If the strange smell or soundcomes out, please pull out thepower plug immediately.- Call A/S center.

▶ ▶

▶ ▶

▶ ▶

4


Do not put steel wires or sharparticles into the gaps or openspaces of the product.- Otherwise, it may cause the electrical

hazard and a failure of the product.

Do not place heater or flammablematerial near product. Do nottrash cigarette into toilet.- Otherwise, it may cause a fire or

a distortion of product.

Do not touch the warm air dryeroutlet with hand.- Otherwise, it may cause burns or a fire.

Please close the input valve on T-shaped connector during the filterchange.- Otherwise, It may cause the electrical

hazard or a failure of the product due toleakage.

▶ ▶

▶ ▶

If the power cord is damaged,please stop using it.- Otherwise, it may cause the electrical

hazard or a failure of the product. Please call A/S center to replace thecord.

Do not drop the remote control.- Otherwise, it may cause a failure of the

product.

▶ ▶

5

Please set the temperature at low(green) for children, the old, andthe one who cannot control thetemperature or has sensitive skin.- Otherwise, it is possible to get

low temperature burns.

※What is the lowtemperature burn? : Burnsfrom the contact with thetemperature under 40℃ for a long period of time.

Do not stand up on the seat coveror put heavy item on it.- Otherwise, it may damage the

product or cause a failure.

Do not lean on the seat coverexcessively.- Otherwise, it may damage and

cause a failure of the product.

Do not put vases, cups, cosmetics,vessels containing drugs or wateron the product. Also do not putsmall metal things on the product.- If they leak or smear in, they may cause

the electrical hazard, a fire, or a failureof the product.

Do not close the seat and seatcover with excessive force.- Otherwise, it may damage or

cause a failure of the product.- Soft cover opens and closes

slowly.

Do not pull out the hose betweenbidet and water cistern.- Otherwise, it may cause leakeage or a

failure of the product.

▶ ▶

▶ ▶

▶ ▶

6


Do not push the keys withexcessive force.- Otherwise, it may cause a failure

of the product.

Do not smudge urine on nozzle oroutlet of warm air dryer.- Otherwise, it may cause smell or a failure

of the product.

Please install the product inplaces avoiding the directsunlight.- Otherwise, it may cause discoloring

and change in color.

Please install with tap water.- If industrial water or heavy water is used,

it may cause damages of skin or skindiseases.

▶ ▶

▶ ▶

Do not use thinner, benzene,chemicals, choride detergent forcleaning. Please use soft cloth or a sponge.- Otherwise, metal parts may corrode, and

discoloring and scratches on productmight appear.

If the product is not used for a longtime, please pull out the plug, andclose the water inlet valve on T-shaped connector. Then drain the water in the chamber.

▶ ▶

7

2. PRODUCT DESCRIPTION

◐ 2-1. Specification

Product Name Coway Bidet

Model No. BA08-AR/AE

Power rating AC 220-240V, 50/60Hz (AC 120V/60Hz for USA)

Power consumption 850W

Power cord 2.5m (1.2m for USA)

Water pressure 0.11~0.68MPa (1.0~7.0 kgf/㎠)

Weight 6.2 ~ 6.8kg

Dimensions

Warm water cleansingdevice

Warm air dryer

Warm seat

MF filter

Accessories

Used temperature

Other function

BA08-AR 525(W) x 500(D) x 142(H) mm

BA08-AE 525(W) x 530(D) x 142(H) mm

Rear cleansing Maximum 0.7ℓ/min, Forced self cleaning function on nozzle

Bidet Maximum 0.7ℓ/min, Forced self cleaning function on nozzle

Operating time Rear cleansing 1 min, Bidet 1 min, Air drying 2 min.

Water pressure control 3 control levels, Micom control

Wide cleansing 3 levels of spray range control (Straight, W1, W2)

Warm water temperature control 4 levels (off:room temperature, low:34℃, moderate:36℃, high:38℃)

Power consumption of cisternheater 800W

Cistern capacity 1.0ℓ

Safety device Bi-metal,Thermal fuse,Temperature sensor

Temperature control 3 levels

Operating time Air drying 2 min.

Power consumption of heater 180W

Safety device Temperature sensor, Thermal fuse(overheat protection)

Power consumption of heater 50W

Safety device Temperature sensor, thermal fuse(overheat protection)

Life span 4 months (2.5ton/month, for under 0.5NTU of turbidity)

Dimensions (L)136 x (Φ)48mm

0~40℃

nozzle position control, move key, nozzle cleaning, Auto powersaving, Muting, Air+

Installation material

3ea of rubber packings, 1ea of MF filter, 1ea of Holder-filter, 1ea of Clip-filter

1ea of fixing plate, 2 ea of fixing bolts, 2 ea of fixing nuts

1ea of T-shaped connector, 1ea of bidet hose, 2ea of fixing sliders

Temperature control forseat(Standard on the room

temperature at 20℃) (Off:room temperature, low:31℃, moderate:34℃, high:37℃)

4 levels

8


◐ 2-2. Structure and name2-2-1. BA08-AR/AE

Front View

Rear View

Seat cover

Seat

Remotecontrol

Main watersupply valve

Toilet cistern hose

Nozzle

T-shapedconnector

Main water pipe

Bidet hose

Cautions

The human bodysensor label

Remote control station

Nano silver filter

Power cord

Cistern plug

Product label

9

◐ 2-3. Dimensions and appearance2-3-1. Dimensions

TYPE : BA08-AE [525 X 530 X 158mm]

TYPE : BA08-AR [525 X 500 X 158mm]

10


◐ 2-3. Dimensions and appearance2-3-2. Appearance

TYPE:BA08-AE

TYPE:BA08-AR

11

◐ 2-4. Remote control functions

Stop keyUse for stopping all functions.

Remote control signal As remote control functions, LED point sends signal.

Rear cleansing keyUse for anal hygiene.

Water temp control keyUse for setting up the warm water temperature.

Bidet keyUse for feminine hygiene.

Nozzle moving keyAdjusting the nozzle position on while cleansing andfunctioning the bidet.

Seat temp keyUse for setting up the seat temperature.

Air dryer keyUse for drying with warm air after female/anal hygiene.

Water pressure/Air dryer temp. keyadjusting the water pressure or air dryer temp. for 3 different levels.

Power keyUse to turn the power on and off, also by remote control. (Power of main device and remote control are off as the funtion stops.)

Wide keyUse for adjusting spray range at 3 different levels.Remark expansion of water fountain on LCD.

Move keyUse for taking advantage of move function while cleaning andfunctioning the bidet.

Air Plus keyMakes mixture of air stream.

Auto cleaning keyCleaning and drying duntions automatically.

12


◐ 2-5. Remote control display

Battery status displayChange the battery when it flashes.

Nozzle movement displayDisplays the position of the nozzle at5 different levels.

Wide displayDisplays the spray ranges at 3 differentlevels.

Water pressure /Warm air dryer temperaturecontrol displayRemark water pressure, warn air tempand Air+.

Warm water temperaturecontrol display Mark established warm water temp.

Seat temperaturecontrol displayMark established seat temp.

Signal status displayDisplays the status of signaling.

13

◐ 2-6. Description of the keys in the main body

You can operate the basic functions of cleansing and nozzle cleaning on themain body without the remote control.

Power keyTurns on and off the main body.

(It functions as 'stop' function whilein use.)

LEDLED will lighten up when the power is on.

(It will flash while the water is heated and itwill flash with a buzzing sound when thereis a problem in the product.)

Remote control signal receiverWindow that receives the remotecontrol signal.

Cleansing keyFor anal cleansing.

Nozzle cleaning keyUse for nozzle cleaning.

Remote control ReceiverReceives the remote controlsignal.

14


◐ 2-7. Features

▼ Improved convenience

� Wide function

User can select the expansion degree of the cleansing water.User can choose between strong and soft spray waterfor cleansing.

� Air Plus function

You can experience softer and stronger cleansing feeling byair mixture stream.

� Nozzle position control

User can choose the position of nozzle as they want.

� Auto powersaving

If the sensor do not detect the human body and there is no controlon the key for 30 minutes, the product is switched to auto powersaving mode and the water temperature and temperature of theseat is re-set to 'low'. The LED in the main body will be switched off.(If anyone sits down or control the key, LED in main body will beturned on.)Setting / cancelling the auto power saving mode1) Turn the power of the remote control on by pressing 'cleaning' key on

the main body. (a beeping sound will occur)2) By pushing 'Cleansing' key on the remote control, desired status

appears.- The auto power saving mode is cancelled when the buzzer rings once.

(clang)- The auto power saving mode is set when the buzzer rings twice.

(clang clang)3) Complete the setting by pressing 'air dryer' key, after choosing the auto

power saving mode. (The buzzer will ring three times-clang clang clang)

15

� Seating lock mode

The cleansing / bidet / air dryer / auto cleansing function willnot be operated, if the sensor does not sense human bodythrough the seating sensor.- The seating lock mode is not set for the initial instalment.

The cleansing / bidet / air dryer / auto cleansing function willbe working regardless of seating status.

Setting / cancelling the seating lock mode1) Please turn on the power of the remote control and plug the

power cord in while pressing the 'cleansing' key. (You will hear a buzzing sound)

2) Please press the 'cleansing' key to set up the auto power savingmode.- The auto power saving mode is cancelled when the buzzer rings

once. (clang)- The auto power saving mode is set when the buzzer rings twice.

(clang clang)3) Complete the setting by pressing 'air dryer' key, after choosing the

auto power saving mode. (The buzzer will ring three times-clang clang clang)

� Muting function

There will be no sound coming out when pressing the key.- The mute mode is not set for the initial instalment.

You will notice the status of the functions with the buzzer.Setting / cancelling the mute mode1) Please turn on the power of the remote control and plug the power

cord in while pressing the 'cleansing' key. (You will hear a buzzing sound)

2) Please press the 'cleansing' key to set up the auto power saving mode.- The auto power saving mode is cancelled when the buzzer rings once.

(clang)- The auto power saving mode is set when the buzzer rings twice.

(clang clang)3) Complete the setting by pressing 'air dryer' key,

after choosing the auto power saving mode. (The buzzer will ring three times-clang clang clang)

16


◐ 2-7. Features

▼ Improved convenience

� Ergonomic seat

Optimized seat for human body is chosen. It is convenienteven for long time use.

▼ Impoved safety

� Sign of the self function

In case of products errors, LED control panel will blink for warning.(While heating water, LED will blink only without beeping.)

� Remote control function

The controlling part of the product is specially made in the formof the remote control for convenience.※ The position of the remote control can be installed in the

right or the left side of the appliance.

� Auto cleansing function

You can run the 'cleansing' function and 'air dryer' functionconveniently with just one key.※ 1 minute of cleansing and 2 minutes of air dry will be

automatically run in order.

17

▼ Improved cleaness

� Move function

During the cleansing or bidet functioning, select 'move'function to move the nozzle forward and backward formuch cleaner cleansing.

� Nozzle self-cleaning function

The cleaning water will be automatically sprayed onto thenozzle for about 5 seconds after the cleansing and bidetfunction and it will always be clean.

� Nozzle cleaning fuction

When the user selected the nozzle cleaning function, the nozzle willbe extended to the maximum length for conveninent nozzle cleaning.※ If you clean the nozzle with an excessive force, it may cause a

failure or the nozzle breakdown. Please grab it with light force.

※ Nozzle cleaning water will be sprayed during the cleaning.(Nozzle without water will come out only if water supply isstopped.)

� Twin nozzle

It is very hygienic since the anal cleansing and female bidetnozzle is separated.

� Nano silver ceramic filter for water purification

MF filter for water purification is adopted for continuouscleaning with purified water.

18

3. INSTALLATION

◐ 3-1. Installation materials

2 ea of fixing bolts

2 ea of rubber packings

2 ea of fixing rubber

Batteries ( 2 AA TYPE)Clip filterHolder filterMF filter

Bidet hose1 ea of screw

1 ea of T-shaped connector

2 ea of fixing washers

2 ea of fixing nuts

Sepatately-sold item ※ Below item is separately-sold and it is for setting up on the wall.

Handle for the senior and disabled

19

◐ 3-2. Procedures3-2-1. Cautions for installation

3-2-2. Existing Seat Disassembling Method

3-2-3. Installing The Main Body

Make sure there is no water leakage on the waterconnection parts after the installation.- Please put the rubber packing in the water hose.

1.

Do not install the product under the direct sunlightor near the heater.- It may cause a fire or a distortion of the product.

2.

Please unscrew the fixing nut to separate the seat①and its cover② .* Please keep them aside for a possible use.

Close the main water valve� to separate the existingwater pipe(water hose)�.

1.

Connect T-shaped connector with existingwater pipe inlet.

1.

�

�

20

3. INSTALLATION

◐ 3-2. Procedures3-2-3. Installing The Main Body

Connect T-shaped connector with the water pipeand bidet hose.* Please insert rubber packing between T-shaped connector

and the water hose.

2.

Connect the filter with the main body of Bidet.* Screw the filter by turning to connect the filter with holder filter.* Insert holder filter into the water tank pipe that is placed in the

bottom left of the main body.

3.

Push in the fixing packing and fixing bolt tohook the heads in the installation board.

4.

Insert fixing bolt into the holes and push in the fixingrubber, fixing washer to prevent the wobbling of themain body. Then tighten up the fixing nuts.*Wobbling of the main body might result an injury of the user.

5.

Connect the bidet hose (that is connected withholder filter) with T-shaped connector.* Try to have the bidet hose as short as possible.

It may make noise if it is too long.

6.

Plug in the power cord into outlet.Outlet with earth connector should be used.* The earth connector lessens the electrical injury.* Plug the power cord into outlet with the earth connector.*When using an extension line, please use rated extension

line with earth connector over 250V 7A.

7.

earthconnector

21

3. INSTALLATION

3-2-4. Installation Method for the Remote Control Station

[ How to change battery ]When changing battery, open the battery cover that isplaced on the back of the remote control.- Please use 2 batteries in AA size. (Check +and - signs of the battery.)- The battery cover is fixed with a screw and make sure the screw and

the rubber ring for the water proof is kept in a safe place.- Tighten the screw.

(It may cause a failure of the product if assembling is not completed.)

8.

Unscrew the screw that is holding the remotecontrol station on the bottom of the main body.

1.

Disassemble the remote control station fromthe main body.

2.

Unscrew the screw that is holding the panel andthe cover panel on the opposite side of the remotecontrol station.

3.

Separate the cover panel from remote controlstation.

4.

22

3. INSTALLATION

◐ 3-2. Procedures3-2-4. Installation Method for the Remote Control Station

Please take the panel out from the remote controlstation and insert it into the other side of the remotecontrol station.* The bigger part of the panel should face

the outside.

5.

Please insert the cover panel on the opposite sideof the remote control station.* Place the two sticking out parts exactly into the two holes in

the cover panel.* Tighten the cover panel.If it is loose, it may result in breakage of the product or aninjury causing product disassembling and parts falling.

6.

Fixing the panel and cover panel with screw.7.

Please take the rubber cap out from the oppositeside of the place where the original remote controlstation was installed in the main body.- Insert the rubber cap that was taken out into the fixing

hole in the opposite side of the remote control station.- If the rubber cap is not inserted, it may cause a failure of

the product.

8.

Insert the remote control station panel andtighten the station with a screw from the bottomof the main body.

9.

23

4. PREPARATION AND CHECKLIST BEFORE USE

▼ Preparation : After installing bidet on toilet, please check the followings before the first use.

Plug the power plug into outlet.

� Plug into outlet of AC 220V with earth connector.<Note>* If plugged, cleaning nozzle is extracted and detracted 1 time for the initialization

of nozzle movement.

<Note>* Do not plug the power until it finishes the establishment. otherwise it may cause a

disorder.* while filter changing, close the service water valve of T-shaped connecting pipe.

<Note>*When turning on/off the remote control, the main body power will operate as well. * If LED is not automatically turned on after seating while LED in main body is off, the

main body auto power saving mode is not turned on.

1.

� Press the power key on control panel or remote controllightly.- LED in the main body will be turned on with a tingling sound.- Main body and the remote control will be turned on when pressing the

power key on the remote control while the main body is not in use.- Only the remote control power will be turned on when pressing the

power key while the main body is not in use.

▼ Checking

Open the main water supply valve by turning thetap counterclockwise.

1.

� LCD window will be turned off and the remote control willbe switched to the power saving mode, if there is nocontrolling for 30 minutes.The remote control status is changed to waiting mode andthe LCD window is lightened up when pressing a randomkey.- If the LCD window does not lighten up after pressing a random key,

the remote control might be turned off. Please press the 'power' keyto turn the remote control on.

Check the control panel.Check the LED light on the main body.

2.

24

5. OPERATING PRINCIPLES

◐ 5-1. Basic Configuration <Note>※When pressing keys on the remote control, buzzer rings from the main body and it means it is

recognizing the signal. (while canceling mute)

Water pressure / warm air temperature key- Adjusts the water / warm air pressure at 3

different levels.

Nozzle position control- Can adjust nozzle position from 1 to 5 level.

Warm water temp control key

- Adjusts the temperature of the warm water at 4 differentlevels, low, middle. High and off.

Seat temp control key- Adjusts the temperature of the seat at 4 different levels,

low, middle, high and off.

Air�key- Makes softer but stronger water stream as a mixture form of

water and air.

Auto Cleansing key- Automatically operates air dry functions for 2 minutes after

cleansing for 1 minutes.

25

◐ 5-2. Main function

▼ Anal Cleansing

While sitting on the seat, press the 'Rear Cleansing'key.

- Cleansing water will be sprayed for 1 minute and willautomatically stop.

- After rear cleansing, forced nozzle cleaning will bedone for 5 seconds.

※ Set the position of nozzle with forward and backwardadjustment key of nozzle movement.

※ Press 'Wide' key for adjusting spray ranges.※ Press 'Air+' key to select the air mixture stream.※ By using the water temperature control, it is possibe to

control the water pressure and move function while using the product.

Cleansing

Move

AirDryer

Stop

Press 'Move' key on the control panel.

- Nozzle will be moved backward and forward forwide cleaning range.

※ It will be moved until the rear cleansing function is on.※ Change the range of nozzle movement is possible via

forward/backward key.※ If you want to stop the movement of nozzle, press

'Move' key again.

Press 'Air Dryer' key on the control panel.

- Warm air will blow for 2 minutes in wet areaduring rear cleansing.

※ It will dry faster if the moisture is slightly removed before use.※ Use strong/weak key, the temperature of the warm air is

controllable.※ If you want to use drying function during rear cleansing, press

'drying' key.

Press 'stop' button on control panel.

- All function at working is halted.

※ Dry function stops 2 minutes after pressing 'stop' key.

26


◐ 5-2. Main function

▼ Bidet Cleansing

While sitting on the seat, press 'Front cleansing' keyon the control panel.

- Cleansing water will be sprayed for 1 minute, and willautomatically stop.

- After front cleansing, the forced nozzle cleaning willbe done for 5 seconds.

※ Please adjust the position of nozzle with nozzle position key.*Press 'Wide' key to adjust the spray ranges.

※ Press 'Air+' key to select the air mixture stream.※ If you press Front Cleansing key during working, it will operate

for the next 1 minute.※ The keys of water temperature, pressure control, move

function are available during working.

Bidet

Move

AirDryer

Stop

Press 'Move' key on the control panel.

- Nozzle will be moved backward and forward forwide cleaning range.

※ It will move until the front cleansing is on.※ Change the range of nozzle movement is possible via

forward/backward key.※ If you want to stop the movement of nozzle, press

'Move' key again.

Press 'Air Dryer' key on the control panel.

- Warm air blows for 2 minutes in wetted areaduring the front cleansing.

※ It will dry faster if the moisture is slightly removed before use.※ Use strong/weak key, temperature of the warm air can be

controlled.※ If you want to use drying function during cleansing, press

'drying' key.

Press 'stop' key on the control panel.

- All working functions will stop.

※ Air dryer function stops 2 secs after pushing "Stop' key.

27

◐ 5-3. Function setting manual(main body)

Division Status Remarks

Function Division Description of function Check

1.Initial

Status

2.Water Filling Mode

Initial status whilepower permit

when RESET Set up equally with the permitted initial power. Conditions of the seat or ID setting merelymaintain previous one.

▷ Initializing nozzle, flow control valve.: Return after maximized extension of cleansing nozzle, Return after rotating2WAY,4WAY in the fullest degree arc.

▷ Fillig water- Water level sensor OFF condition: Operate the water filling as the power truned

ON at the main body.- Water level sensor ON condition : Maintaing standby condition.

(Refer to the water refilling mode for specific information) ▷ Initial set-up

Initial power input

☞ While water level sensor is OFF▷When warm water heater is OFF and power is ON, the water is supplied

actively by OPEN valve.- switched to the stand-by mode after the water level sensor is ON, followed

by the additional water supply for 5 sec.▷ ERROR mode is proceeded if it does not fill the water up even after 2 mins

of the water supply.(refer to the extra attched ERROR mode for specific ERROR operation)

☞ While water level sensor is ON▷ Maintaing stand-by mode

Status of powerpermitted,

while superior sensor isOFF on functioning

▷ To cancel a function on the process, turn the warm water OFFProcess the water filling as same as the initial water filling.

Power OFF Impossible to operate all functions andindicated as OFF

Functions regardless of seating.

Operates when connected with seatingcondition

Memorizes set up value after setting initial "1"

Force of waterpressure 2 levels

Nozzle position standard(3 levels)

Air dryer temp 1st level

OFF

OFF

cancel

set up

"1"

Warm water temp

Seat temp

Seat sensorcognition

Power savingfunction

ID set up

28



☞ Select▷ Operate cleansing by pressing "Cleansing" key on the main body or on the remote

control.▷When selecting cleansing while others are functioning, cancelling others and

operating cleansing.▷ In case of air drying, air dry heater will be turned OFF immediately,motor stops

after 2 secs, followed by power OFF.☞ Operate▷ a buzzing sound once.▷ Nozzle,transfer flow control valve to setting position →Water supply valve OPEN▷ (Extend about 1 min) during cleansing, when input cleansing key, gets cleansing hour

recounted.- Continuous repeatitions are available.

▷When select the other options while cleansing, operate chosen function after the rearcleansing.

☞ Select▷When inputing the "Stop" key,▷ After 1 min of cleansing. ▷When choosing bidet, air dry, auto cleansing while cleansing. ▷ In case of time extension - when the seat sensor was off more than 5 sec.

(when seat sensor is in cognition mode)☞ Operate▷ a buzzing sound once.▷ Nozzle keeping and cleaning.▷ After the completion of back cleansing, removes remaining water in the nozzle:

by operating AIR PUMP for 3 secs it removes remaining water.

☞ Select▷ Bidet operate when "Bidet" is pressed on the remote control.▷When Bidet is selected while others are functioning, it activates Bidet with the

cancellation of the other functions which were on the process.▷ In case of air drying, it instantly turns OFF the dry heater and after that, motor turns

OFF after 2 secs and activates Bidet.☞ Operate > a buzzing sound once.▷ Nozzle,transfer flow control valve to setting position → water supply valve OPEN▷While Bidet, as it is inputted again, Bidet key is recounted in Bidet hour.

(extend about 1 min)- Continuus repeatition is available.

▷When selecting other fuction while Bidet is activating, the selected fuction will followafter the rear cleansing.

☞ Select▷When inputting the "Stop" key,▷When 1 min. passed of Bidet hour ▷When selecting cleansing, air dryer, and auto cleansing functions while

Bidet is activating. ▷When last seating sensor is OFF more than 5 secs.

( in case of seat sensor in cognition mode)☞ Operate▷ a buzzing sound once.▷ nozzle keeping and cleaning▷ Activation of the removing remained water after finishing rear cleansing:

removing remained water by functioning AIR PUMP for 3 secs.

Operate

Stop

Operate

Stop

3.Cleansing

4.Bidet

Function Division Description of function Check

29

Function

5.Air Dryer

6. Auto

Cleansing

Division

Operate

☞ Select▷ Activate the air drying when "air dryer" key is pressed on the remote control.▷ when choosing air dryer while others are functioning, it cancels functions on the

process and activate air drying.☞ Operate▷ a buzzing sound once.▷ Recounting air drying hour when inputting the air drying key again during the air

drying.(extend for 2 mins) - continous repetition is available.

▷ Immediately air drying FAN function activates and activate the air dry heater afer 2 secs.

☞ Select▷When inputting "Stop" key,▷ After 2 mins of air drying. ▷When selecting cleansing, air dryer, and auto cleansing functions while air drying. ▷When the seat sensor lasts in OFF mode more than 5 secs.

(in case of the seat sensor is in cognition mode)☞ Operate▷ a buzzing sound once.▷ Immediately turn the air dry heater OFF and air dry moter also stops afer 2 secs.

▷ Air dry temp. can be adjusted in 3 different levels(OFF 1st level, 2nd level) by the waterpressure / air key on the remote control.

* Measurementmethod :Refer the productstandard

☞ Select▷ To activate auto cleansing by pressing "auto cleansing" key on the remote control.▷When selecting auto cleansing while others are functioning, it actives auto cleansing

with cancellation of the functions on the process.▷ In case of air drying, dry heater will instantly turned OFF.

The motor will also be turned OFF after 2 secs and auto cleansing wil be activated.☞ Operate▷ a buzzing sound once.▷ Nozzle,transfer flow control valve to setting position → water supply valve OPEN▷ Activate cleansing in order (1 min) → air dryer (2 mins)▷ Setting condition when selecting the auto cleansing.

▷When inputting the auto cleansing key again during the auto cleansing, the same action isrepeated as follows.- Extend 1 min during cleansing.- Extend 2 mins during air drying.

▷When selecting other functions during auto cleansing, selected function will be activatedafter rear cleansing.(namely, do not function rear cleansing while air drying)

☞ Select▷When inputting "Stop" key, ▷ After cleansing 1 min + air dryer 2 mins. ▷ when selecting other functions (Cleansing,Bidet,Air dry) while others are functioning. ▷ In case of the seat sensor was turned OFF for more than 5 sec.

(when seat sensor is in setting mode) ☞ Operate▷ a buzzing sound once.▷ Cleansing to finish or stop: nozzle keeping and cleaning,to activate removing remained water

after finishing rear cleansing: removing remained water by functioning AIR PUMP for 3 secs tofinish or stop the air drying: when air dry heater stops, the air dry motor will stop after 2 sec.

Stop

Control Temp

Operate

Stop

Description of function Check

Set-up

Temp(℃) Room temp 32 36

POWER vol. 0 60% 80%

1st Level (Off) 2nd Level 3rd Level

Waterpressure

Maintain previous status

WIDE Nozzleposition

Warm watertemp Seat temp Air dryer temp

30



Function

7.Air+

☞ Select▷ Choose Air condition by pushing "Air+" on the remote control.▷ While Air+ is set, if you push it again, it cancels. It is repeated whenever you push it. (Toggle action)▷ Choose among functions(cleansing, bidet, auto cleansing), it cancels the others.

☞ Operate▷ a buzzing sound once. ▷When it choose Air+: when it is functioning, activates Air Pump and mixing air like before.▷When it cancel Air+: when it is functioning, no activation of Air Pump and mixing air occur.▷ amount of Air mixture per water pressure.

8.Water volumn control

▷ Control the water force by 3 different levels by using the water pressure/water dryertemp on the remote control.

▷ Control the nozzle position by 5 different levels by using the nozzle position control keyon the remote control.

*Cleansing position value was measured from TOP COVER to the location where the waterplace is attached to the body.

▷When choosing, a buzzer sound will occur once. ▷ Activate cleansing movement when pressing "move" key on the remote control while

cleansing, Bidet or auto cleansing is functioning.▷ Cancel the cleansing move by pressing "move" key again while cleansing movement is on

the process.

▷When choosing, a buzzing sound will occur once. ▷When pressing "wide" key during cleansing is functioning. Bidet or the auto cleansing

get changed into 3 different levels (straight → extension 1 → extension 2)▷ Impossible to input "wide" key while air drying is on the process.

▷When inputting the power (initialization), set "OFF" as the initial setting. ▷ Set temp. by the "warm water temp" control key.▷When pressing the "warm water temp" key on the remote control, it changes in order

OFF → 1st level → 2nd level → 3rd level.▷Whether it is functioning or standing by, temperature setting is available.▷ How to test: refer to the product standard.

▷When inputting the power (initialization), set "OFF" as the initial setting. ▷ Set temp. by "seat temp" control key.▷When pressing "seat temp" key on the remote control, it changes in order OFF→

1st level→ 2nd level→ 3rd level.▷Whether it is functioning or standing by, temperature setting is available.▷ How to test: refer to the product standard.

9.Nozzle position control

10.Operate

11. The expansion of water spray

12.controltemp

Warm water temp

Seat temp

Division Description of function Check

Water pressure set-up

approve voltage approve voltage 15V 18V

pressure set-up 1st Level 2nd Level

Set-up

Set-up

Set-up

Set-up

Temp(℃) Room Temp 31±3 34±3 37±3

OFF 1st Level 2nd Level 3rd Level

Temp(℃) Room Temp 33±2 36±2 39±2

OFF 1st Level 2nd Level 3rd Level

MovingDistance Moving about 6mm per level.

Standard-2 Standard-1 Standard Standard+1 Standard+2

Nozzle Water Vol(cc/min) 500±50 600±50 700±50

1st Level 2nd Level 3rd Level

31

Function

13.auto

powersaving

14.Cleaning

(Nozzle Cleaning)

15.Power

16.Removing remaining water

17.Freezing protection

18.Protection for low-temp burns

19.TEST Mode

(SELF TEST Mode)

20.ERROR MODE

Set-up

Canceling

▷When it has no input from the remote control signal or control keys on the main body for 30 mins after the seat sensor is OFF, it switches to the power saving mode which sets up the 1st level of warm water and seat temp automatically.

▷ Equally activates even tbe seat sensor is in cancel mode (NORMAL status).▷While it is in the power saving mode, the LED on the main body turns OFF.

▷When the seat sensor control is ON, input of the remote control signal or control keys on main body cancel the power saving mode and activate in the previously set temp.

▷When the remote control signal is inputted, the temp. is set to the previous setting through the remote control signal.

▷When canceling the power saving mode, LED on the main body turns off.

▷ Activate cleansing by pressing "cleansing" key on the main body: maximize nozzle andwater supply only in 2AWY cleansing.- When pressed once,maximizes extension of bidet nozzle

twice, maximizes extension of cleansing nozzlethree times, returns to the starting point (cleansing completed).

▷ After choosing cleansing, 2 mins passes for each clansing, finishes cleansing and the nozzle returns.

▷When inputting "stop", "power" through the remote control or the main body duringcleansing, it cancels cleansing and nozzle returns.

▷Whenever you push the power on the main body, the power turns ON/OFF. (TOGGLE action) ▷ Power OFF: every function is cancelled. (heater turns OFF and during the process,

previous one is returned to starting point, by marking area OFF) impossible to input through the remote control signal.

▷ Power ON : sets the temp. and LED returns to the previous setting.possible to input through the remote control signal.

▷While functioning, act as the stop key and while on stand by, act as the power ON/OFF.

▷ Activate the removing of the remaining water after cleansing, bidet, auto cleansing:removing remaining water from the nozzle by functioning AIR PUMP for 3 secs.

▷ Rise until 6℃ of cognition temp. by the warm temp heater if one of the warm waterthermistor(water supply sensor or flood sensor) are below 5℃. If there is no water, heater will not be activated (water level OFF).

▷When setting "3 levels" on the seating temp., low temp burn protection activates. ▷ Description

- Seat temp. will rise until the set temp. and will go lower by 1℃ after 5 mins and another. 1℃ lower after 10 mins. if it does not sense whether the seat is set in the right temp.

▷ Setting up the TEST mode- When the power activates by pushing the "power+cleansing" keys together on the main

body, access into TEST set mode. (a buzzing sound will occur on program version in the marked area)

- With this status, when pushing keys on the remote control likewise, it is selected to thededicated mode.

- When pushing "Cleansing" on the remote control: Cleansing operates successivelyWhen pushing "Bidet": Bidet operates successively When pushing "Stop":activate the cleansing (1 min)+bidet (1 min) successively in order. When pushing "Air dryer": activate the cleansing (1 min)+bidet (1 min)+air dry (2 mins)successively in order.

- Among the above, when inputting "move" key, it operates.▷ TEST mode cancellation: TEST mode is cancelled by pushing.

"power" on the main body or on the remote control.

▷ Refer to the attached SHEET in extra.

Division Description of function Check

32



Function

21.Specialset up

Category

Remote controladdress set up

Setting/cancellingmute

Power saving modeon/off

Seating sensorsetting/cancelling

Water drainning(drainning the line

water out)

Program versionchecking

Movement details

▷ Address is originally set to '1'.▷When power is supplied by pressing 'power' key, ID setting mode will be on.

(with a buzzing sound) : The 'cleansing' signal of the initial remote control is entered in this status,the entered ID will be set to the main body.

▷ Mute is originally off for the default. (There will be a buzzing sound when pressing the key.)▷ Setting/cancelling mute mode.

- Please turn the power of the remote control on and plug the power cord in while pressing the 'cleansing' key. (You will hear a buzzing sound)

- Mute mode will be set after pressing 'stop' key on the remote control.- Mute mode will be cancelled when pressing 'stop' key on the remote control while mute mode is on.

▷ How to cancel the special set up mode.- Set up mode will be cancelled after pressing the 'air dryer' key on the remote control or after 30

seconds, and it will be changed to waiting mode. (The buzzer will ring three times-clang clang clang) ※While the mute mode is set: There will not be a buzzing sound when pressing the key.

(But, there will be a buzzing sound for an error while setting up the seating mode.)※While mute mode is on: There will be a buzzing sound when pressing the key.※ Setting/cancelling the sound mode: mute cancelling→ buzz once(clang), mute setting→ buzz

twice(clang, clang)※ If the current set up is saved on EEPROM, the current set up will be remained when there was a

electricity failure.

▷ Power saving mode is originally set for the default.▷ How to set/cancel the power saving mode.

- Plug the power cord in while pressing the 'cleansing' key, and it will be automatically changed tosetting mode. (You will hear a buzzing sound)

- Power saving mode will be cancelled when pressing 'cleansing' key on the remote control.- Auto power saving mode is set when pressing 'cleansing' key while the power saving mode is off.

▷ How to cancel the special set up mode.- The set up mode will be deactivated after pressing 'air dryer' key on the remote control or after 30seconds from mode activation. (Buzz sound will be on: clang, clang, clang)

※While the power saving mode is on: Warm water temperature, seat temperature will be set to 'level 1' to activate the auto power saving mode if the keys on main body key are not pressed or there is no remote control input for 30 minutes, regardless of seating status.

※While the power saving mode is off: The power saving mode will not be activated under the same condition as above.

※ Sound: power saving mode cancel→ buzz once(clang), power saving mode set→ buzz twice(clang, clang)

※ If the current set up is saved on EEPROM, the current set up will be remained when there was a electricity failure.

▷ Seat sensor mode is not originally set for the default. (any function can be controlled regardless of seating status)

▷ How to set/cancel the seat sensor mode.- Plug the power cord in while pressing the 'cleansing' key, and it will be automatically

changed to setting mode. (You will hear a buzzing sound)- Seat sensor mode will be cancelled when pressing 'bidet' key on the remote control. - Seat sensor is deactivated when pressing 'bidet' key on the remote control while

seat sensor mode is on.▷ How to cancel the special set up mode.

- The set up mode will be deactivated after pressing 'air dryer' key on the remote control or after 30 seconds from mode activation. (Buzz sound will be on: clang, clang, clang)

※While seat sensor mode is on: any functions will activate when seat sensor senses seating.※While seat sensor mode is not on: any functions will activate regardless of eating status.※ Sound: seat sensor mode cancel->buzz once(clang), seat sensor mode set→ buzz twice

(clang, clang)※ If the current set up is saved on EEPROM, the current set up will be remained when

there was a electricity failure.

▷Water drainning mode- Plug the power cord in while pressing the 'cleansing' key, and it will be automatically

changed to setting mode. (You will hear a buzzing sound)▷Water drain movement: water supply valve will be opened for 10 seconds, 2WAY valve

will be positioned to its cleaning position, AIR PUMP It will be switched to the waiting mode after the activation.

▷ Plug the power cord while pressing 'power+cleansing' key on the main body together, and it will be turned into the confirming mode. Check the versions with buzzing sound.

Check

33

◐ 5-4. Water output levels during cleansing / bidet

◐ 5-5. Power consumption(electricity cost)

■Water output levels during cleansing/bidet (Water output can be varied in each set.)

Levels

Water output(ml/min) 500 (±10%) 600 (±10%) 700 (±10%)

1 2 3 Note

■ Standard Calculation(Family of 4 people with 2 males and 2 females)/daily use rate: cleansing 4 times,bidet 8 times, air drying 12 timesCASE 1 : Water output level 2, water temperature level 1, air drying temperature level 2, seat OFF

(room temperature:20'C, water temperature:20'C)

CASE 2 : Water output level 2, water temperature level 3, air drying level 3, seat level 3(room temperature:10'C, water temperature:5'C)

■ Unplug the power cord after use to save the electricity cost.

- The progressive tax will be applied according to the electricity use. The electricity cost can be varied depends on basic rate per section and cost per kwh.

- Example of the electricity cost calculation: cost calculation for 272kWh of electricity use per month: please refer to http://www.kepco.co.kr/cyber/

- For household(low pressure) (based on the standard made in May, 2006 by Korea Electronic Power Corporation)

▶These results are electricity cost only, basic rate, elctric power industry fund, value added tax according to the electricity use are not included.

Electricity cost(won)

Cost increase due tobidet use(won)

Section 1

Section 2

Section 3

Section 4

Section 5 401 ~ 500kWh electricity use

Under 100kWh electricity use

101 ~ 200kWh electricity use

201 ~ 300kWh electricty use

301 ~ 400kWh electricity use

1

2

3

4

5

6

Basic rate(ignored the rates below won)

Electricity use(ignored the rates below won)

Electricity cost in total

Electric power industry fund(ignored the rates below 10 won)

Value added tax(with rounding off below won)

Cost in total(ignored the rates below 10 won)

1,430won

Step 1 : 100kWh X 55.1won = 5,510won

Step 2 : 100kWh X 113.8won = 11,380won 29,007won

Step 3 : 72kWh X 168.3won = 12,118won

1,430won + 29,007won = 30,437won

(30,437won) X 0.037 = 1,120won

(30,437won) X 0.1 = 3,044won

30,437won + 1,120won + 3,044won = 34,600won

370

820

1,430

3,420

6,410

for first100kWh or less

for next 100kWh

for next 100kWh

for next 100kWh

for next 100kWh

55.1

113.80

168.30

248.60

366.40

CASE 2 (166.7 KWh)

CASE 1 (28.50 KWh) ＼3,187

＼15,017

＼4,713

＼24,341

＼4,475

＼35,968

＼6,596

＼53,048

＼20,130 ＼39,960 ＼70,490 ＼115,500

Power consumption(kWh)

NO.

NO. Cost Cost(won)

Basic rate(won/household) Electricity cost(won/kWh) Note

200 300 400 500 Note

34

◐ 5-6. Resistance and voltage values (10㏀/25℃/2.5V) for various temperatures on temperature sensor (T1, T2, seat)


(10㏀/25℃/2.5V)Temperature

(°C)Temperature

(°C)Resistance

(㏀)Voltage

(V)Resistance

(㏀)Voltage

(V)Temperature

(°C)Resistance

(㏀)Voltage

(V)

0 27.39

26.23

3.66

3.62

3.58

3.53

3.49

3.44

3.40

3.35

3.31

3.26

3.21

3.17

3.12

3.07

3.02

2.98

2.93

2.88

2.83

2.78

2.74

2.69

2.64

2.59

2.55

2.45

2.41

2.36

2.31

2.27

2.22

2.18

2.14

25.13

24.08

23.08

22.13

21.22

20.36

19.53

18.74

17.99

17.27

16.59

15.93

15.31

14.71

14.14

13.59

13.07

12.57

12.10

11.64

11.20

10.78

10.38

9.633

9.281

8.944

8.621

8.311

8.014

7.729

7.456

1

2

3

4

5

6

7

8

9

11

12

13

14

15

16

17

18

19

20

21

22

23

24

26

27

28

29

30

31

32

33

10

34 7.194

6.942

2.09

2.05

2.01

1.96

1.92

1.88

1.84

1.80

1.76

1.72

1.68

1.65

1.61

1.57

1.54

1.50

1.47

1.44

1.40

1.37

1.34

1.31

1.28

1.25

1.22

1.19

1.16

1.13

1.11

1.08

1.05

1.03

1.01

6.701

6.469

6.247

6.033

5.827

5.630

5.440

5.258

5.083

4.914

4.752

4.596

4.446

4.302

4.163

4.029

3.900

3.776

3.656

3.541

3.430

3.323

3.220

3.121

3.025

2.932

2.843

2.757

2.674

2.593

2.516

35

36

37

38

39

40

41

42

43

45

46

47

48

49

50

51

52

53

54

55

56

57

58

59

60

61

62

63

64

65

66

44

67 2.441

2.369

0.98

0.96

0.93

0.91

0.89

0.87

0.85

0.83

0.81

0.79

0.77

0.75

0.73

0.72

0.70

0.68

0.67

0.65

0.63

0.62

0.60

0.59

0.58

0.56

0.55

0.54

0.52

0.51

0.50

0.49

0.47

0.46

0.45

2.299

2.232

2.167

2.104

2.043

1.984

1.928

1.873

1.819

1.768

1.718

1.670

1.624

1.578

1.535

1.492

1.452

1.412

1.373

1.336

1.300

1.265

1.231

1.198

1.167

1.136

1.106

1.077

1.048

1.021

0.9946

68

69

70

71

72

73

74

75

76

78

79

80

81

82

83

84

85

86

87

88

89

90

91

92

93

94

95

96

97

98

99

77

35

6. DISASSEMBLY AND ASSEMBLY

◐ 6-1. Cautions for disassembly and assembly

◐ 6-2. Tools required

▼ Before disassemble the product- Please stop the water supply by closing the valve of main water pipe.- Please unplug the power cord for the prevention of the electrical hazard.- Please drain the water cistern.

: During service, if the water splatters, it might cause electrical hazard.Drain the water out by opening drain cap.

▼ Please return to the original state in Wiring path of product and water hose.- Some electrical components use insulation material for safety.- Wiring path of lead wire is needed to be careful for not being near to heating/moving/sharp

components.- Wiring path of lead wire and united band is a part of the safety device.- Before putting on the cover, please check whether the water hose is connected right.- After servicing, please assemble to original state.

▼ After servicing, please conduct safety check.- Check whether the nuts, components, lead wires are in the original state.- Check whether the cover of lead wire is damaged.- Please check for an abnormal water flow and heat after reassembly.- Please check whether every switch functions normally.

■ Monkey wrench■ '+' shaped driver■ '-' shaped driver■ Nipper■ Long nosed pliers■ Gimlet

※ Please take caution not to damage and distrort in every component during disassembly.

36


◐ 6-3. Disassembly method for each part6-3-1. Disassembly method for top cover, body frame [Needed tool : '+', '-' shaped drivers]

1 Unscrew 2 cover screws on top cover.

Separate 2 screws using '+' shape driver.

Separate top cover and body by putting '-' shapeddriver into the position on the picture.

Separate top cover from body as shown in picture.

Separate terminal which connected to seat.(shown in picture).※Do not put excessive force when separating terminal.

Otherwise, it might be broken.

2

3

4

5

�

�

37

6-3-2. Disassembly method for top cover, damper, seat cover, seat [tool : '+' shaped driver needed]

1 Pull out seat cover in the direction of the arrow.

Unscrew the damper fixing screw inside of top cover,and pull out damper in the direction of the arrow.

Remove one screw using '+' shaped driver. Turn the cover guide wire in the direction of the arrow and pull it out to the left.

After separating damper, disassemble seat as withsequence of arrow direction.

2

6Top cover and body frame is completely separated in this picture.

3

4

�

�

�①

②

38


◐ 6-3. Disassembly method for each part6-3-3. Disassembly method for Main, POWER PCB [tool : '+' shaped driver needed]

6-3-4. Disassembly method for SUB-R, SUB-L PCB [tool : '+' shape driver needed]

1Separate 2 screws as in the picture and pull the PCB out.

Separate connected connector.※Terminal might be damaged if too much strength is placed.

Extract PCB by unscrewing 5 screws on picture.

2

3

Separate 2 screws in the position of the pictureto separate PCB.

Separate 2 screws in the positionof the picture to separate PCB.

1

2

��

39

6-3-6. Disassembly method for nozzle ASS'Y [tool : '+' shaped driver needed]

1 Disassemble 1 screw on the position in picture.

Disassemble 1 screw on the position in picture.

Separate 2 air pump fixing screws and silicon hose.

Separate the lead wire that is fixed on nozzle cover in the direction of the arrow.

2

1Remove 2 screws as in the picture and separate the air dryer ASS'Y.

3

4

6-3-5. Disassembly method of Air Dryer ASS'Y [tool : '+' shaped driver needed]

40


◐ 6-3. Disassembly method for each part6-3-6. Disassembly method for nozzle ASS'Y [tool : '+' shaped driver needed]

5Separate the 2-way valve silicon hose in the direction of the arrow.

Separate the ass'y nozzle cover in the direction of the arrow.

Separate 1 screw as in the picture.

Separate 2-way valve silicon hose in the direction of the arrow.

Lift nozzle ASS'Y up in the direction of the arrow and separate.

6

7

8

9

�

�

�

41

On nozzle operation, constriction of nozzle mighthappen due to a failure. Push the constricted nozzle with proper force till youhear a clicking sound.※Where, coming out of opposite nozzle is normal, and take a

caution not to put excessive force to prevent damages onnozzle gear.

After pushing one side of nozzle, push back theother side of nozzle with proper force. Also, pleasetake a caution not to put excessive force.Displace power cord, and hold for 30 seconds.Reconnect power cord, and check the operation ofnozzle.

1

2

3



Separate cistern ASS'Y as in the picture.

1

2

6-3-7. Disassembly method for water cistern ASS'Y [tool : '+' shaped driver needed]

6-3-8. Problem solving for constriction of nozzle due to movementerror during nozzle ASS'Y operation.

�

�

�

42


◐ 6-4. Disassembly diagram6-4-1. Product disassembly diagram

N0 Part Name

COVER SEAT

Code No

1200-00177-00

1224-00021-00

1224-00022-00

1240-00023-00

1200-00179-00

1263-00017-00

1263-00016-00

1200-00156-00

1291-00056-00

1200-00174-00

1240-00007-00

1241-00051-00

1401-00043-04

1201-00089-00

1250-00032-00

1200-00183-00

1250-00029-00

1240-00028-00

1240-00024-00

1530-00015-00

1520-00030-00

1200-00164-00

Material and Specification

ABS

POM

POM

SILICONE, DARK GRAY

ABS

PC 0.25T,3M 300MP,한

PC 0.25T,3M 300MP,한

SOFT PVC, WHITE

내경¢N18,선경¢2,EPDM

ABS

TOK

EPDM,경도50도,BLACK

ELONGATE TYPE, WHITE PINK,BA08

ABS

STS 304 1.5T

NORYL SE1GFN2(BLACK)

STS304 1.0T

EVA, 35*12*1.2T, BLACK

EPDM

-

-SILINCONE,경도40도,WHITE

Q’ty

1

1

1

1

1

1

1

2

1

1

1

1

1

1

2

2

1

1

1

1

1

1

BUSH-COVER LEFT

BUSH-COVER RIGHT

CUSHION-COVER

COVER-TOP

INLAY-PANEL RIGHT

INLAY-PANEL LEFT

COVER-SCREW

O-RING-COVER GUIDE

COVER-GUIDE WIRE

DAMPER-TWIN AXIS

PACKING-DAMPER

ASS'Y SEAT-

BODY-FRAME

PLATE-SHAFT

HOUSING-SHAFT

PLATE-EARTH

FOAM-DRYER PAD

CUSHION-DRYER

ASS'Y POWER CORD-

ASS'Y PCB-RIGHT

CAP-JOINT

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

N0 Part Name

CAP-CONNECTOR

Code No

1200-00163-00

1250-00035-00

1211-00018-00

1290-00011-00

1432-00076-00

1200-00161-00

1550-00007-00

1431-00027-00

1550-00006-00

1520-00033-00

1520-00035-00

1200-00181-00

1200-00180-00

1424-00001-00

1400-00086-00

1221-00012-00

1400-00085-00

1240-00025-00

1202-00031-00

1560-00006-00

1202-00033-00

Material and Specification

ABS

EPDM,42.5X11.5 2.5T

STS 304 1.5T

M12 POM

-

ABS

-

-

-

-

-

ABS

NORYL, SE1GFN2

-

-

ALDC

-

SILICONE

PC,배면스프레이,전면실크인쇄SPRAY

BA 08-A

PC,배면스프레이,전면실크인쇄SPRAY

Q’ty

1

2

1

2

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

SHEET-BODY FRAME

FIXER-BRACKET

BOLT-INSTALL

ASS'Y NOZZLE-

COVER-NOZZLE

ASS'Y PUMP-AIR

ASS'Y TANK-

ASS'Y FAN MOTOR-DRYER

ASS'Y PCB-MAIN

ASS'Y PCB-POWER

HOUSING-LOWER R/C

HOUSING-BUSH

ASS'Y BUSH-SHAFT

ASS'Y COVER-SHAFT

SHAFT-CONTROLLER

ASS'Y HOUSING-UPPER R/C

CUSHION-R/C

DECO-R/C

ASS'Y REMOT CONTROL-

DECO-TOP

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

40

41

42

43

321

3332292827

30

16

15

14

24

25

26

42 37 3435 36 38

39

40

41

13

10

9

8

5

43

4

67

12 11

31

1518 19 21

20

22

23

43

6-4-2. Disassembly diagram of nozzle

N0 Part Name Q’ty Material Remark

4

3

2

1 BODY NOZZLE

COVER NOZZLE

ABS

ABS

ABS

ABS

ABS

ABS

ABS

ABS

ABS

ABS

POM

POM

POM

POM

POM

STS304

ABS MP-211, NTR1EA

1EA

1EA

1EA

1EA

1EA

1EA

1EA

1EA

1EA

1EA

1EA

1EA

1EA

1EA

1EA

ABS MP-211, NTR

ABS MP-211, NTR

ABS MP-211, NTR

ABS MP-211, GREEN

ABS MP-211, YELLOW

ABS MP-211, GREEN

ABS MP-211, YELLOW

ABS MP-211, GREEN

ABS MP-211, YELLOW

DUCT NOZZLE

CYLINDER CLEAN

CYLINDER BIDET

TIP CLEAN

TIP BIDET

TIP CLEAN UPPER

TIP BIDET UPPER

TIP CLEAN LOWER

BODY TIP BIDET LOWER

GEAR CAM

GEAR DRIVER

GEAR REDUCER 1

GEAR REDUCER 2

SPRING NOZZLE

5

6

7

8

9

10

11

12

13

14

15

16

N0 Part Name Q’ty Material Remark

20

19

18

17 COVER NOZZLE SPRING

GEAR PINION

ABS

POM

NBR

ABS

ABS

-

Fe+Zn

Fe+Zn

-

SILICONE

SILICONE

SILICONE

SILICONE

SILICONE

SILICONE

SILICONE

ABS MP-211, NTR1EA

1EA

1EA

1EA

1EA

1EA

2EA

2EA

1EA

4EA

1EA

1EA

1EA

1EA

1EA

1EA

ABS MP-211, NTR

ABS MP-211, NTR

DC24V

2-3X10 TAP PH Fe+Zn

2-4X12 TAP PH Fe+Zn

DC24V

BLUE

GREEN

PINK

YELLOW

NTR

NTR

SEAL SHAFT MOTOR

CONNECTOR NOZZLE CLEAN

CONNECTOR NOZZLE BIDET

MOTOR MOVE

SCREW TAPPING

SCREW TAPPING

ASS'Y VALVE 4WAY

O-RING CLEAN

ASS'Y HOSE SILICONE

ASS'Y HOSE SILICONE

ASS'Y HOSE SILICONE

ASS'Y HOSE SILICONE

HOSE SILICONE

HOSE SILICONE

21

22

23

24

25

26

27

28

29

30

31

32

24

25

24

21

20

14

2

4

526

3

8

9

6

7

1011

1

12

1315

18

19

22

23

23

16

17

44

7. SIGNS OF FAILURE AND WAY TO REPAIR (Refer to the electrical wiring during signs.)

No

1 No power on.

- Check power supply.

- Check power cord is plugged.

Supply power

Supply power

Replace PCB

Turn the mute option off.

Replace PCB-Main

Change connector connection

Replace PCB-Main

Change hose connection

Supply water

Replace Sol v/v

Replace 4-way v/v

Replace 2-way v/v

Replace fan

Change connector, replace fan

Replace PCB

Replace air dryer heater

Replace air dryer heater

Replace PCB

Replace PCB

Replace PCB

Change polarity of connector


Replace MAIN PCB

Replace 2-way v/v

Replace PCB-Main

Only working when power is ON

Replace nozzle ass'y

Replace PCB

Replace water cistern or tighten bolt


- Check failure of PCB(Main/Power/Sub)

- Check mute option.

- Check pattern failure in PCB Main and buzzer.

- Check connection of PCB connector.

- Check PCB-Main.

- Check hose for bending and slipping.

- Check water supply.

- Check inlet Sol v/v.

- Check 4-way v/v.

- Check 2-way v/v.

- Check air dryer FAN.

- Check connector and wire (including polarity check)

- Check operating power(PCB).

- Check open of the air dryer heater.

- Check open in thermal fuse of air dryer heater.

- Check PCB

Check open in triac of air dryer heater.

- Check PCB

- Check connector (including polarity check)

- Check the interference from hose connected to nozzle.

- Check waveform putput in Step Motor.

- Check 2-way v/v.

- Check PCB-Main

- Check the running with power on.

- Check move motor.

- Check PCB.

- Check the leakage in water cistern.

- Check hose for slipping.

Power is on, but no sound.

Cleansing/Bidet function is not working.

Air drying function is not working.

Only air of room temperature isblowed during air drying.

Only warm air is blowed duringair drying.

Move operation is not working.(Including nozzle position control)

Water pressure control is notworking.

Nozzle cleaning is not working.

Water is leaking.

2

3

4

5

6

7

8

9

10

Problem Check list Repair method

45

No

11 Water is coming out throughnozzle during stop.

- Check the inlet sol v/v.

- Check water level sensor.

Replace inlet vavle

Replace water level sensor

Supply main water

Replace inlet vavle

Replace water level sensor

Replace PCB-Main

Replace warm water heater

Replace PCB

Replace bimetal

Replace thermal fuse

Replace nozzle ass'y

Replace PCB-Main

Supply main water

Replace inlet vavle

Change the battery.

Replace PCB.

Replace PCB.

- Check main water.


- Check water level sensor.

- Check PCB-Main operation.

- Check open in warm water heater.

- Check PCB.

- Check bimetal.

- Check thermal fuse.

- Check move motor.

- Check PCB-Main.

- Check main water.


- Check the battery is charged.

- Check remote PCB.

- Check main body PCB.

No water is supplied.

Warm water is not sprayed.

Nozzle is not extended.

Nozzle extends but no waterduring the cleansing/bidet.

Remote control does not receive and send.

12

13

14

15

16

Problem Check list Repair method

46

8. ERROR INDICATION MODE (LED)

■ On error occurrence, LED of water pressure/air dryer is blinking and buzzer will be ringing.There are No. 1 to 8 errors, and details are as follows.

No

1 1

No water. (Full water level is not detected while water incoming.)Full water level is not detected after 2 minutes of water supply.

1. Error will occur when the sensor does not sense the water filling while the water supply valve is opened for 2minutes.Water supply valve will be closed and error indication will be continued when the water filling level is not sensed eventhough the water supply valve was opened for 3 minutes.

2. Number 1 will be repeated and it will automatically cancelfunction, even though the remote control, main body iscontrolled or there was a seating sensed.

3. It will be turned into waiting mode when the causing factor is removed.

1. Repetitive Error signal2. All the functions will stop3. Error will disappear when power is supplied again.

1. All the functions will stop. Error will be displayed.2. Error will disappear when power is supplied again.

1. All the functions will stop. Error will be displayed.2. Error will disappear when power is supplied again.3. If the temperature is higher than 45℃ on either T1 or

T2, nozzle self cleaning will be operated and there willbe water supply to prevent from temperature raising.

1. Cleansing or bidet function will stop.2. Repetitive Error signal3. Error will disappear when power is supplied again.




Water leakage error Error will occur when water level is decreasing and filling in repeatition more than 7 times for 3 minutes.

Seating temperature is over heated Error will occur when the seat is hotter than 51℃ for at least 2 seconds.

Temperature thermistor is over heated. Error will occur when the temperature of water outlet is sensored(T2) higher than 45℃ and nozzlecleaning will be automatically done to supply water.(Water supply will stop on a certain temperaturethat was set)

Warm water heater is not working.Warm water temperature is not changing whenthe water outlet sensor (T2) was performed for a while, even though warm water temperaturewas set to stop. (1℃ within 3 minutes) But, it only applies when the temperature of T2 is below 25℃

Warm water themistor #1 open/shortWarm water themistor #2 open/short

Seat thermistor open/short

Failure of auto flush movement.Lead switch sensored when the water is flushed and the lead switch does not turn offwithin 30 seconds.

2 2

3 3

4 4

5 5

6 6

7 7

88

Number ofbuzzer ringing Errors and problems Indication or cancellation method

47

9. ELECTRICAL WIRING

48

10. DESCRIPTION SUMMARY OF PCB CONNECTOR

◐ 10-1. Main PCB Connector

� CN12 (Move Motor) : pin#1~4 : (-), pin#5,6 : 24V(+)� CN22 (Auto Flush) : pin#1,2,4,5 : (-), pin#3 : 24V(+), pin#6 : signal (auto flush sensor),

pin#7 : GND ( only BA08-B TYPE is applied )� CN15 (4Way Motor) : pin#1 : 24V(+), pin#2~5 : (-)� CN17 (2Way Motor) : pin#1 : 24V(+), pin#2~5 : (-)� CN25 (Main ↔ Sub PCB-L) : pin#1 : 5V(+), pin#2 : signal(SW1), pin#3 :

pin#4 : signal(LED2), pin#5 : GND� CN11 (Water Level Sensor) : pin#1 : GND, pin#2 : 5V(+), pin#3 : signal(water level)� CN18 (Seat temperature Sensor) : pin#1 : signal(seat temperature sensor), pin#2 : GND� CN20 (Outgoing water temperature sensor) : pin#1 : signal(Outgoing water temperature sensor),

pin#2 : GND� CN19 (Seat Sensor) : pin#1 : GND, pin#2 : 5V(+), pin#3 : signal(seat sensor)� CN21 (Incoming water temperature sensor) : pin#1 : signal(Incoming water temperature sensor),

pin#2 : GND� CN16 (Dry Fan) : pin#1 : 24V(+), pin#2 : high : (-), low : 24V(+)� CN14 (Water IN v/v) : pin#1 : 24V(+), pin#2 : high : (-), low : 24V(+)� CN23 (Air Pump) : pin#1 : 24V(+), pin#2 : high : (-), low : 24V(+)� CN10 (Main ↔ Power PCB) : pin#1 : 24V(+), pin#2 : 12V(+), pin#3 : 5V(+),

pin#4 : high : (-), low : 5V(+), pin#5 : high : (-), low : 5V(+)pin#6 : high : (-), low : 5V(+), pin#7 : GND

� CN13 (Main ↔ Sub PCB-R) : pin#1 : 5V(+), pin#2 : signal(SW3), pin#3 : signal(Remote), pin#4 : GND

987654

3

2

1

10 1112 13

14

15

49

◐ 10-2. Power PCB Connector

◐ 10-3. Sub PCB Connector

� CN9 (Power PCB I/O ↔ Main PCB) : pin#1 : 24V(+), pin#2 : 12V(+), pin#3 : 5V(+) pin#4 : high : (-), low : 5V(+), pin#5 : high : (-), low : 5V(+) pin#6 : high : (-), low : 5V(+), pin#7 : GND

� CN2 : Water Heater L� CN7 : Water Heater N� CN6 : Air dryer heater� CN5 : AC Power N ( power input 220V )� CN4 : AC Power L� CN3, CN8 : Seat Heater

� CN1 (Sub PCB L ↔ Main) : pin#1 : 5V(+), pin#2 : signal(SW1sensor), pin#3 : signal(SW2sensor)pin#4 : signal(LED2 on/off control), pin#5 : GND, pin#6 : signal(IR receiver)

� CN24 (Sub PCB R ↔ Main ) : pin#1 : 5V(+), pin#2 : signal(SW3sensor),pin#3 : signal(IR receiver), pin#4 : GND

↔ ( Sub PCB L ) ↔ ( Sub PCB R )

3

2

4

5

1 2

6

7

1

50

11. LIST OF A/S COMPONENT

▼ For BA07-R/E

No. Component schematic Details

1

2

3

4

5

6

ItemKorean

English

Code number

Quantity

Specification

ItemKorean

English

Code number

Quantity

Specification

ItemKorean

English

Code number

Quantity

Specification

ItemKorean

English

Code number

Quantity

Specification

ItemKorean

English

Code number

Quantity

Specification

ItemKorean

English

Code number

Quantity

Specification

아세이 커버-톱 세미

ASS'Y COVER-TOP SEMI

1 / Woongjin Cuchen

ABS, WHITE

커버-스크류

COVER-SCREW

16340106700

2 / Hwa-in chemical

SOFT PVC, WHITE, BA07 share

인레이 판넬-리모콘-A

INLAY PANEL R/C-A

1 / Art and tech

PET, 0.25T, 3M 300MP, A-TYPE

인레이 판넬 좌

INLAY PANEL LEFT

1 / Art and tech

PC 0.25T, 3M 300MP, Korean

인레이 판넬 우

INLAY PANEL RIGHT

1 / Art and tech

PC 0.25T, 3M 300MP,Korean

하우징-샤프트

HOUSING-SHAFT

2 / Sam-woon industry

NORYL GFN2

51


7

8

9

10

11

12

ItemKorean

English

Code number

Quantity

Specification

ItemKorean

English

Code number

Quantity

Specification

ItemKorean

English

Code number

Quantity

Specification

ItemKorean

English

Code number

Quantity

Specification

ItemKorean

English

Code number

Quantity

Specification

ItemKorean

English

Code number

Quantity

Specification

댐퍼-동축

DAMPER-TWIN AXIS

16431000900

1

TOK, BA06, BA07 share

커버-가이드 와이어

COVER-GUIDE WIRE

1 / Dong-il chemical

ABS,WHITE

캡-조인트

CAP-JOINT

1 / Dong-bang silicon

SILICONE, solidity 40degree, WHITE

아세이 커버-시트 세미

ASS'Y COVER-SEAT SEMI

1 / Je-seong

ABS, WHITE

쿠션-커버

CUSHION-COVER

1 / Dae-seong chemical

SILICONE, DARK GRAY

라벨-주의

LABEL-CAUTION

1 / Bio-label

Seat caution label, Korean

52



13

14

15

16

17

18

ItemKorean

English

Code number

Quantity

Specification

ItemKorean

English

Code number

Quantity

Specification

ItemKorean

English

Code number

Quantity

Specification

ItemKorean

English

Code number

Quantity

Specification

ItemKorean

English

Code number

Quantity

Specification

ItemKorean

English

Code number

Quantity

Specification

회로도-

SCHEMATIC DIAGRAM-

1 / Bio-label

220~240VAC, 235*104*T0.07

아세이 시트-

ASS'Y SEAT-

1 / Woongjin Cuchen

220VAC 50W, 10A 72'C

캡-커넥터

CAP-CONNECTOR


ABS, WHITE, BA08

아세이 피시비 메인

ASS'Y PCB-MAIN

1 / Bi-seong electronics

clear PC

아세이 피시비 파워

ASS'Y PCB POWER


clear PC, SMPS

아세이 피시비-좌

ASS'Y PCB-LEFT


clear PC

53


19

20

21

22

23

24

ItemKorean

English

Code number

Quantity

Specification

ItemKorean

English

Code number

Quantity

Specification

ItemKorean

English

Code number

Quantity

Specification

ItemKorean

English

Code number

Quantity

Specification

ItemKorean

English

Code number

Quantity

Specification

ItemKorean

English

Code number

Quantity

Specification

아세이 피시비-우

ASS'Y PCB-RIGHT


clear PC

와이어-메인 파워 I/O

WIRE-MAIN POWER I/O

1 / Shin-won electronics

24AWG, 7PIN

아세이 리모콘

ASS'Y REMOTE CONTROL


BA08

케이스-리모콘

CASE-R/C

1 / Nam-woong electronics

PC(HI-1002ML)

머신스크류-

MACHINE SCREW-

1 / Han-seong bolt

M3X10, STS304

아세이 노즐-

ASS'Y NOZZLE-

1 / CNS

54



25

26

27

28

29

30

ItemKorean

English

Code number

Quantity

Specification

ItemKorean

English

Code number

Quantity

Specification

ItemKorean

English

Code number

Quantity

Specification

ItemKorean

English

Code number

Quantity

Specification

ItemKorean

English

Code number

Quantity

Specification

ItemKorean

English

Code number

Quantity

Specification

케이스-노즐

CASE-NOZZLE


ABS

아세이 팁-비데

ASS'Y TIP-BIDET

1 / CNS

MP-211,light yellow

아세이 팁-세정

ASS'Y TIP-CLEAN

1 / CNS

ABS,MP-211,light green

아세이 탱크-세미

ASS'Y TANK-SEMI

1 / Jeon-o electronics

BA08

캡-아웃렛

CAP-OUTLET

1 / Dong-il chemicals

ABS

플레이트-체크

PLATE-CHECK

1 / Dae-seong chemical

EPDM

55


31

32

33

34

35

36

ItemKorean

English

Code number

Quantity

Specification

ItemKorean

English

Code number

Quantity

Specification

ItemKorean

English

Code number

Quantity

Specification

ItemKorean

English

Code number

Quantity

Specification

ItemKorean

English

Code number

Quantity

Specification

ItemKorean

English

Code number

Quantity

Specification

오링-아웃렛

O-RING-OUTLET


inside diameter ¢22,pretilt ¢2.2,EPDM

아세이 솔레노이드 감압밸브

ASS'Y SOLENOID-REDUCING VALVE

1 / ForS-tech

DC24V

아세이 히터 탱크

ASS'Y HEATER-TANK

1 / Sang-do electronics industry

220VAC,800W_250V/10A, 72'C

아세이 바이메탈

ASS'Y BIMETAL

1 / Mi-rae electronics parts

250VAC/10A/55℃

아세이 에어펌프

ASS'Y PUMP-AIR

1 / ForS-tech

BA08

아세이 밸브-체크

ASS'Y VALVE-CHECK

1 / ForS-tech

BA08

56



37

38

39

40

41

42

ItemKorean

English

Code number

Quantity

Specification

ItemKorean

English

Code number

Quantity

Specification

ItemKorean

English

Code number

Quantity

Specification

ItemKorean

English

Code number

Quantity

Specification

ItemKorean

English

Code number

Quantity

Specification

ItemKorean

English

Code number

Quantity

Specification

아세이 써미스터 T1

ASS'Y THERMISTOR-T1

1 / Dae-gwang sensor

25℃, 10㏀, L50

아세이 써미스터-T2

ASS'Y THERMISTOR-T2

1 / 광센서ㄜDae-gwang sengor

25℃, 10㏀, L25

아세이 플로트센서

ASS'Y FLOATE SENSOR

1 / Yu-il system

5VDC/100㎃

아세이 캡-드레인

ASS'Y CAP-DRAIN

16220119900

1

BA07 share

아세이 팬모터 건조

ASS'Y FAN MOTOR-DRYER

1 / Sam-gang tech

BA08

아세이 팬-모터-건조 세미

ASS'Y FAN-MOTOR-DRYER SEMI

1 / Dae-seong electronics

24VDC, 3000RPM

57


43

44

45

46

47

48

ItemKorean

English

Code number

Quantity

Specification

ItemKorean

English

Code number

Quantity

Specification

ItemKorean

English

Code number

Quantity

Specification

ItemKorean

English

Code number

Quantity

Specification

ItemKorean

English

Code number

Quantity

Specification

ItemKorean

English

Code number

Quantity

Specification

아세이 케이스-건조

ASS'Y CASE-DRYER

1 / ㄜ Sam-gang tech

BA08

히터 건조

HEATER-DRYER

1 Sam-gang tech

220VAC 180W, 105℃/192℃

도어-윈드

DOOR-WIND

1 / sam-woon tech

flame retardant PP

아세이 파워코드

ASS'Y POWER CORD

1 / Dong-a electronics plug

250VAC 2.5M WHT 3*0.75㎟

아세이 필터-MF

ASS'Y FILTER-MF

16239913300

1 / Picogram

MF, WHITE, Print, BA07 share

홀더-필터

HOLDER-FILTER

1 / Picogram

POM, BA06 share

58



49

50

51

52

53

54

ItemKorean

English

Code number

Quantity

Specification

ItemKorean

English

Code number

Quantity

Specification

ItemKorean

English

Code number

Quantity

Specification

ItemKorean

English

Code number

Quantity

Specification

ItemKorean

English

Code number

Quantity

Specification

ItemKorean

English

Code number

Quantity

Specification

필터클립

CLIP FILTER

16370101600

1 / Han-seong bolt

STS316, BA03, BA06, BA07 share

아세이 밸브-T

ASS'Y VALVE-T

1 / Seung-gwang

BA07 share

아세이 볼트-설치

ASS'Y BOLT-INSTALL

2 / Hwa-in chemical

BA08 only

급수호스어세이

ASS'Y INLET HOSE-A

16220114200

1

For bidet

아세이 서비스 키트 A(노즐포함)

ASS'Y SERVICE KIT-A

1 / Woongjin Cuchen

BA08 only, 160*117.5,GREEN

아세이 서비스 키트 B(노즐제외)

ASS'Y SERVICE KIT-B

16239913000

1 / Woongjin Cuchen

BA06, BA07 share

59


55

56

57

58

ItemKorean

English

Code number

Quantity

Specification

ItemKorean

English

Code number

Quantity

Specification

ItemKorean

English

Code number

Quantity

Specification

ItemKorean

English

Code number

Quantity

Specification

아세이 커넥터-필터

ASS'Y CONNECTOR-FILTER

1

POM

와이어 바이메탈

WIRE BI-MATAL

1 / Shin-won electronics

UL1015 18AWG 105'C

패킹-아웃렛

PACKING-OUTLET


inside diameter¢20.2 ,pretilt¢2.0 ,EPDM

아세이 하우징-리모콘

ASS'Y HOUSING-R/C

1 / Woongjin Cuchen

BA08

60

12. DDO DDO SERVICE

▼ Filter change

Detach filter 1

Grab the holder-filter (in case of clipdetaching) and hold the main body of thefilter, then turn it in the direction of the arrow. (unscrewe)

Detach filter 2

Pull out the filter downwards.

Inserting the filter in

Follow the reverse procedure of the above to put filter in.

※ Caution : Please close water inlet valve before changing filter.

�▼ Nozzle cleaning

Press nozzlecleaning button onthe right once

Extension of front cleansingnozzle (cleaning)

Press nozzlecleaning buttononce (retract frontcleansing nozzle)

Rear cleansingnozzle is extended (cleaning)

Press Stop /power button

If there is noinput for 2minutes,automaticallyrepositioned.

※ Do not handle the nozzle with excessive force when cleaning the nozzle, it may cause breakage of the nozzle or failure of the product.Please grab it lightly when cleaning.

※ During nozzle cleaning, nozzle cleaning water is sprayed.(If there is no water in cistern, only nozzle is extended.)

� �

61

▼ Replacing the nozzle tip

Wear plastic glove in nozzle tip replacing kit, andprepare the replacing tip.(1ea for anal cleansing, 1ea for bidet cleansing)

On � and �, hold the nozzle cylinder in onehand to fix, and pull out the existing nozzle tip.Replace the old one with new one .

Wash with disinfection gauze, and trash into envelope.

▼ Cleaning the exterior

Use neutral detergent on a soft sponge or clothand rub it on the exterior of the product.

- Do not use detergent containing clorine, thinner,benzene or abradant, or rough cloth.

- It may cause deformation of the product ordamage on the product.

▼ Product storaging

Unscrew the nut from the fixing bolt and lift themain body up to separate them.

* Power cord should be unplugged whendisassembling and bidet hose should beseparated.

* Drain the water out from the water tank whenproduct is not used for a long time.

service manual - cowaycoway.ir/upload/manual/service manual/ba-08 svc manual(100203).pdf · 3...

Documents