8/8/2019 Series 601-M Air Gap Drains for Use With MasterSeries Reduced Pressure Assembly Specification Sheet

http://slidepdf.com/reader/full/series-601-m-air-gap-drains-for-use-with-masterseries-reduced-pressure-assembly 1/1

Dimensions WeiGHTs

A B C D E F G H

in. mm in. mm in. mm in. mm in. mm in. mm in. mm in. mm lbs. kgs.

131 ⁄ 8 333 63 ⁄ 8 162 53 ⁄ 8 137 31 ⁄ 2 89 313 ⁄ 16 97 27 ⁄ 32 56 43 ⁄ 8 111 97 ⁄ 8 251 2.2 1.0

Dimensions and Weights

Size: 21

 ⁄ 2"-10" (65mm-250mm)

Series 601-MAir Gap Drains for Use WithMasterSeries® Reduced Pressure AssemblySizes: 21 ⁄ 2" - 10" (65mm-250mm)

ES-F-601L

S P E C I F I C AT I O N S H E E T

Job Name ––––––––––––––––––––––––––––––––––––––––––– Contractor ––––––––––––––––––––––––––––––––––––––––––––

Job Location ––––––––––––––––––––––––––––––––––––––––– Approval –––––––––––––––––––––––––––––––––––––––––––––

Engineer –––––––––––––––––––––––––––––––––––––––––––– Contractor’s P.O. No. ––––––––––––––––––––––––––––––––––

Approval –––––––––––––––––––––––––––––––––––––––––––– Representative ––––––––––––––––––––––––––––––––––––––––

Argap Dra sd Vw sr 860Argap Dra Frt Vw sr 880

Part nubr: 905213

 Air Gap Drain KitThe FEBCO Series 601 Air Gap Drain Kit is constructed of coated aluminum.The air gap drain is designed to be attached to the relief valve ofMasterSeries® reduced pressure assemblies, sizes 21 ⁄ 2" - 10"(65mm – 250mm). Four inch drainage piping may be attached to drain,creating a system that catches and removes minor relief valve dischargesdue to pressure fluctuations and/or minor check valve fouling.

Note:The gap drain is not designed to catch the maximum discharge pos-sible from the relief valve. The installation of FEBCO air gap with the drainline terminating above a floor drain will handle any normal discharge or nui-sance spitting through the relief valve. However, floor drain size may need

to be designed to prevent water damage caused by a catastrophic failurecondition. Do not reduce the size of the drain line from the air gap fitting.

Features• Nozzledesigndirectsflowdirectlyintofunnel,reducingsidespray.

• Funnelsminorreliefvalvedischargesintodrains.

• Lightweightforeasyinstallation.

• Coatedforcorrosionresistance.

• 4"(100mm)funneloutletisdesignedtoacceptahublesspipecouplingfor simple drain pipe installation.

 

MaterialsNozzle: ASTMB26Alloy356

Funnel: ASTMB26Alloy356

Rods: ASTMB241Alloy6063Coating  Pratt&Lambert,Inc.Vitralon  polyurethanecoatingblack#88-1204 

or equivalent

601

USA: 4381 N. Brawley • Ste. 102 • Fresno, CA • 93722 • Tel. (559) 441-5300 • Fax: (559) 441-5301 • www.FEBCOonline.com

Canada: 5435 North Service Rd. • Burlington, ONT. • L7L 5H7 • Tel. (905) 332-4090 • Fax: (905) 332-7068 • www.FEBCOonline.ca

ES-F-601L 0704 © 2009 FEBCO

 A Watts Water Technologies Co mpany 

FEBCO product specifications in U.S. customary units and metric are approximate and are provided forreference only. For precise measurements, please contact FEBCO Technical Service. FEBCO reserves theright to change or modify product design, construction, specifications, or materials without prior noticeand without incurring any obligation to make such changes and modifications on FEBCO products pre-viously or subsequently sold.

Frt Vw

Ful

Rd

nzzl

sd Vw

A

H

D

B C

G

Be