select and erect terrestrial antennas.pdf
TRANSCRIPT
-
7/28/2019 Select and Erect Terrestrial Antennas.pdf
1/50
Select and Erect Terrestrial Antennas
Rev Date: 20-Oct-06 - 1 - NSW DET 2006
A Learning Object in support of the
Certificate II in Antennae Equipment
UEE21205 from the National
Electrotechnology Training Package
UEE05
7. Select and Erect
Terrestrial Antennas
-
7/28/2019 Select and Erect Terrestrial Antennas.pdf
2/50
Select and Erect Terrestrial Antennas
Rev Date: 20-Oct-06 - 2 - NSW DET 2006
NSW Department of Education andTraining (DET) 2006
All rights reserved. This work is
copyright to NSW Department ofEducation and Training.
Permission is given to trainers andteachers to make copies byphotocopying or other duplicatingprocesses for use within their owntraining organisations, or in aworkplace where training is beingconducted.
This permission does not extend tothe resale of this material to thirdparties, the making of copies for use
outside the immediate trainingenvironment for which they are made,and the use of the materials for hire.
Outside these guidelines, all materialis subject to copyright under theCopyright Act. 1968 (Commonwealth)and permission must be obtained inwriting from the NSW Department ofEducation and Training.
Disclaimer
The views expressed in this work do
not necessarily represent the views ofthe NSW Department of Educationand Training. The NSW Departmentof Education and Training does notgive warranty nor accept any liabilityin relation to the content of this work.
Resource Development Team
David Neyle, Lightship PeopleSystems
Product Advisory Committee
Mike Horne, ElectroSkills Centre
Peter Bowd, NSW TAFE
Naomi Dinnen, NSW UEITAB
Deborah Griffin, NSW DET
Giselle Mawer, Giselle Mawer andAssociates
Technical Reference Committee
George Kozak
Stephen Creese, Matchmaster
Peter OConnor, Foxtel
Graham La Motte, NSW TAFEOTEN
Copyright Acknowledgements
The assistance of Matchmaster isacknowledged in the production ofthis learning object.
Acknowledgment
This work has been produced initiallywith the assistance of fundingprovided by the NSW Department ofEducation and Training, TrainingDevelopment Unit, through theTraining Resources & SupportProgram with advice from the ProductAdvisory Committee.
Further copies of this resource areavailable from:
Website:www.skillsonline.net.au
For further information,contact:
Email:
-
7/28/2019 Select and Erect Terrestrial Antennas.pdf
3/50
Select and Erect Terrestrial Antennas
Rev Date: 20-Oct-06 - 3 - NSW DET 2006
Table of Contents
INTRODUCTION ............................................................................. 4
LEARNING OUTCOMES ................................................................ 5
MAPPING TO TRAINING P ACKAGE............................................. 6
ELECTROMAGNETIC RADIATION................................................ 7
FREQUENCY ....................................................................................................7
WAVELENGTH ..................................................................................................8
SIGNAL PROPAGATION......................................................................................8
SIGNAL POLARISATION....................................................................................11
BASIC ANTENNAS....................................................................... 12
THE DIPOLE...................................................................................................12
PRACTICAL ANTENNAS ....................................................................................14
ANTENNA CHARACTERISTICS ...........................................................................15
COMMERCIAL ANTENNAS.................................................................................16
FREE-TO-AIR (FTA) TELEVISION SIGNAL STANDARDS ......... 20
ANALOG TELEVISION STANDARDS ....................................................................20
DIGITAL TELEVISION STANDARDS .....................................................................21
RADIO FREQUENCY ........................................................................................23
TV BANDS AND FREQUENCIES IN AUSTRALIA.....................................................24
DIGITAL COMPATIBILITY WITHANALOG INSTALLATIONS .......................................26
CARRIER TO NOISE RATIO ...............................................................................31
FREE AIR ATTENUATION..................................................................................32
REQUIRED SIGNAL LEVEL AT ANTENNA................................. 34
ANALOG SIGNAL LEVELS .................................................................................34
DIGITAL SIGNAL LEVELS ..................................................................................34SUMMARY OF REQUIRED TV SIGNAL FACTORS ..................................................36
BALUNS........................................................................................ 37
COMBINING ANTENNAS ............................................................. 38
ANTENNA SEPARATION ...................................................................................39
INCREASING GAIN...........................................................................................41
SITE SURVEY .................................................................................................42
CONCLUSION............................................................................... 45
SELF ASSESSMENT.................................................................... 46
-
7/28/2019 Select and Erect Terrestrial Antennas.pdf
4/50
Select and Erect Terrestrial Antennas
Rev Date: 20-Oct-06 - 4 - NSW DET 2006
Introduction
When you look at the rooftop
level of any suburb you willsee TV antennas mounted on
a variety of styles of hardware.
As you move from place to
place, between city and rural
areas, you will notice that the design of the antenna varies.
Sometimes the elements are longer or shorter. Sometimes the
boom length will be very long, or the antenna will be mounted very
high on a guyed m ast. In some regions the antenna is mounted
sideways, in others it lies parallel with the ground. There are
specific and good reasons why various styles and designs of TV
antennas are used throughout Australia.
The careful selection and installation of the correct antenna (or
antennas) for the location you are working in will ensure a
satisfactory TV picture, whether it is for the older analog system, or
the newer digital TV system. It is also important that you
understand some basic concepts about how television signals are
transmitted and received, as this will determine the types of
antenna system components you will use to ensure a satisfactory
installation.
This Learning Object will introduce you to the different factors that
influence the design of TV antennas so that you can correctly select
or specify the requirements for antennas that you use in
installations.
-
7/28/2019 Select and Erect Terrestrial Antennas.pdf
5/50
Select and Erect Terrestrial Antennas
Rev Date: 20-Oct-06 - 5 - NSW DET 2006
LEARNING OUTCOMES
When you have completed this Learning Object you will be able to:
Describe in simple terms the concepts of frequency and
wavelength.
Name different types of TV antenna.
Describe the characteristics and differences between analog
and digital free-to-air television signals.
State the frequency bands used for television transmission inAustralia and the lower and upper frequencies that a TV
installation must be designed for.
Perform simple calculations using decibels.
Describe how RF travels through free space and the causes of
signal attenuation.
State the required signal levels at the output of the antenna
necessary to receive a high quality picture.
Perform an antenna site survey.
Calculate the required antenna gain based upon the results of a
site survey.
Select an appropriate antenna for the site at which it is to be
installed.
Describe the use of diplexers and baluns.
Position multiple antennas.
-
7/28/2019 Select and Erect Terrestrial Antennas.pdf
6/50
Select and Erect Terrestrial Antennas
Rev Date: 20-Oct-06 - 6 - NSW DET 2006
Self Assessment
After reading through this Learning Object you will find a series of
questions that you should attempt. This will enable you to check
your level of understanding and knowledge before progressing ontoyour workplace assessment.
You should not request a workplace assessment unless you have
attempted these questions, checked your answers, and are
confident that you can achieve a satisfactory outcome.
Recognition of Prior Learning
If you believe you are already competent in the content of this
Learning Object then you should check yourself out with the Self
Assessment questions and then request a workplace assessment.
Mapping to Training Package
This learning object provides knowledge and skills for parts/aspectsof the following Unit of Competence:
UEENEEH008A Assemble and erect reception antennae andsignal distribution equipment
In particular, it addresses the following Essential Knowledge and
Skills from the Training Package UEE05:
2.10.14(a) The common difficulties associated with TVreception.
2.10.15(a) Propagation of radio waves from a transmitter to areceiver.
2.10.15(b) Characteristics of antenna systems.
2.10.15(c) Selection of antennae systems for variousapplications.
2.10.15(d) Installation techniques for antenna to receiver andantennae to transmitter transmission and distributionsystems.
-
7/28/2019 Select and Erect Terrestrial Antennas.pdf
7/50
Select and Erect Terrestrial Antennas
Rev Date: 20-Oct-06 - 7 - NSW DET 2006
Electromagnetic Radiation
A television signal transmitted from any site is a form of
electromagnetic radiation; this radiation has both an electric and
magnetic field component and as such is induced into most metallic
objects. However a receiving antenna that is tuned to the
frequency of the transmitter will be much more effective in the
reception of signal able to be used by a receiver or processed by a
distribution system.
It is for this reason that the elements of antennas are of different
lengths, depending upon the frequency they must receive.
Frequency
Electromagnetic radiation is measured according to the number of
times the signal changes per second; one cycle change per second
is known as one Hertz (Hz), one thousand changes per second is
one Kilohertz (kHz), one million changes per second is one
Megahertz (MHz) and one billion changes per second is oneGigahertz (GHz).
Fig 7.1: 1 Hz wavelength
A one Hertz s ignal: a singlesine wave cycle in onesecond.
1 sec Time
-
7/28/2019 Select and Erect Terrestrial Antennas.pdf
8/50
Select and Erect Terrestrial Antennas
Rev Date: 20-Oct-06 - 8 - NSW DET 2006
Wavelength
The distance an electromagnetic wave travels in the course of one
cycle is known as the wavelength. Since electromagnetic radiation
travels at the speed of light (300,000,000metres/second) thewavelength can be calculated as follows:
Wavelength (metres) = 300 divided by the frequency in MHz
(You may also see this formula written as: = 300 / f )
This means that the wavelength of a 300MHz signal is 1 metre
It follows that the lower the frequency, the longer the wavelength
and the higher the frequency, the shorter the wavelength.
Example
Channel 28 has a vision carrier frequency of 527.25MHz. The
wavelength is therefore 300 527.25 = 0.57 metres.
Task 7.1
What is the wavelength of Digital Ch 9a, which has a centre
frequency of 205.5MHz?
________________________
Signal Propagation
Electromagnetic signals radiated from a transmitter can be
reflected, refracted, and diffracted as the signal travels through the
atmosphere.
Reflection
Reflection occurs when the electromagnetic energy hits an object
and some of the energy is then reflected away at an angle.
-
7/28/2019 Select and Erect Terrestrial Antennas.pdf
9/50
Select and Erect Terrestrial Antennas
Rev Date: 20-Oct-06 - 9 - NSW DET 2006
Fig 7.2: Reflection
Large buildings (skyscrapers), mountains and hills, and even
passing aircraft, can cause reflections of TV signals, and are the
major cause of ghosting.
Ghosting
When a TV signal is reflected the TV antenna may receive two of
the same signals, the second arriving slightly later (because of the
longer path length) and at a lower signal strength. The more
correct term for ghosting is multipathing. On an analog TV this
causes a second image to appear slightly beside the main picture.
(Digital TV is not affected by ghosting, and in fact a multipath signal
can actually enhance digital reception.)
The selection of an appropriate model of TV antenna that has a
high front-to-back ratio (for ghost signals coming in from the rear of
the antenna) or an antenna with a narrow acceptance angle (forghost signals coming in from the sides) will help to deal with
ghosting problems.
Refraction
Refraction occurs when the signal passes through a change of
density/temperature of the atmosphere. This results in a bending or
refraction of the signal as it passes through that layer. Lower
frequencies (HF) are more susceptible to this than higher
frequencies (VHF and UHF).
Solid
-
7/28/2019 Select and Erect Terrestrial Antennas.pdf
10/50
Select and Erect Terrestrial Antennas
Rev Date: 20-Oct-06 - 10 - NSW DET 2006
Fig 7.3: Refraction
On rare occasions refraction can cause TV signals to travel much
further than the intended coverage area, causing interference to
local TV stations. (TV channel allocations in different regions have
been carefully selected to minimise the problems caused by
refraction.)
Diffraction
Diffraction occurs when the signal grazes the edge of an object
(e.g. the tops of mountains) and tends to bend around that edge.
(The same effect explains how you can see a cars headlights over
the crest of a hill before you see the main headlight beam come into
view.)
Fig 7.4: Diffraction
Even though VHF and UHF signals travel in straight lines (line ofsight) it also explains why hilly areas can still receive some signal,
-
7/28/2019 Select and Erect Terrestrial Antennas.pdf
11/50
Select and Erect Terrestrial Antennas
Rev Date: 20-Oct-06 - 11 - NSW DET 2006
even though the receiver is somewhat shadowed from the
transmitter.
Signal Polarisation
During particular atmospheric conditions (usually caused by
refraction, also known as ducting) a TV signal can travel much
further than normally intended. If the different TV signals are on the
same frequency they will cause a distorted picture on the analog
receiver. To help avoid this problem some signals are transmitted
with horizontal polarisation and others are transmitted with vertical
polarisation. A correctly polarised TV antenna will reject the
unwanted signal by approximately 20dB.
Capital cities in Australia usually have horizontally polarised signals,
and many regional areas have vertically polarised signals. (In
regional Australia it is quite common to see a combination of
vertical and horizontally polarised antennas used at the one location
to receive the full complement of available signals.)
Polarisation is defined by the plane that the elements of the
antenna are in. If the elements are horizontal, then the antenna is
receiving a horizontally polarised signal. The opposite is true for
vertically polarised signals.
The three issues of reflection, refraction and diffraction can have an
impact on antenna selection for television reception. TV antenna
designs and characteristics are covered in the following sections.
-
7/28/2019 Select and Erect Terrestrial Antennas.pdf
12/50
-
7/28/2019 Select and Erect Terrestrial Antennas.pdf
13/50
Select and Erect Terrestrial Antennas
Rev Date: 20-Oct-06 - 13 - NSW DET 2006
require connection to a balanced 70 ohm feeder cable. If the
antenna is folded, as shown below, the impedance at the centre of
the dipole is approximately 300 ohms (balanced).
Fig 7.7: Basic Folded Dipole
In most cases, connection to a standard 75 coaxial cable requires
the use of a balun (covered later in this Learning Object).
Characteristics of the Dipole Antenna
Directivity
A simple dipole will receive signals from either direction (at right
angles to the dipole). This receiving performance (or the strength of
the received signal at different angles of incidence) is known as
directivity and is specified by a polar diagram.
The receiving characteristic of a simple half wave dipole is used as
standard and is used to compare the directivity of more complicated
receiving antennas.
Transmission line to receiver.
wavelength foldeddipole.
300 ohms impedance
Fig 7.8: Simple dipole antenna and a graphic representationshowing which direction it receives signal from. (A polardia ram.
-
7/28/2019 Select and Erect Terrestrial Antennas.pdf
14/50
Select and Erect Terrestrial Antennas
Rev Date: 20-Oct-06 - 14 - NSW DET 2006
Practical antennas
Parasitic Elements
The receiving performance of a simple dipole can be modified by
the presence of additional elements adjacent to the dipole. The
dipole connected to the feeder cable is called the driven element,
while elements not connected to the feeder are called parasitic
elements. A parasitic element slightly shorter than the driven
element and placed in front of it will reinforce the pick-up from the
forward direction; it is known as a director. A parasitic element
slightly longer than the driven element and placed behind it will also
help to reinforce the pick-up from the forward direction and reduce
the pick-up from the rear. This element is known as a reflector.
An antenna such as this combining a driven element with a director
and reflector is known as a Yagi antenna; the name is applied to
many variations of this basic design. Any number of directors can
be used but only one reflector or reflecting system is used for any
one frequency.
D
irector
Re
flector
Driven
Element
Fig 7.9: Changing the directivity of a basic dipole
by the addition of a director and reflector.
-
7/28/2019 Select and Erect Terrestrial Antennas.pdf
15/50
Select and Erect Terrestrial Antennas
Rev Date: 20-Oct-06 - 15 - NSW DET 2006
If a parasitic element is positioned very close to the driven element,
variations of its length and its distance from the driven element will
modify the current distribution in the driven element. By doing this,
the driven element can be made resonant over a particular range of
frequencies and its impedance can be changed. A parasitic
element used in this way is referred to as a resonator or phasing
element.
Antenna Characteristics
As well as the frequency range covered (the channels that the
antenna can receive) there are two other characteristics of the
antenna that you, as an installer, will be interested in. These are:
Gain, and
Front-to-Back ratio
Gain
The gain of an antenna is the power of the signal received by the
antenna compared to that received by a reference dipole; this is
Example of a Yagi antenna,showing one rear reflector and a
number of directors.
Fig 7.10: Shown here is a typical polar diagram for a Yagi antenna. It hasa large forward receiving lobe and a small rear lobe. This gives itincreased output signal power compared to a basic dipole. It also gives itan ability to reject undesired signals coming from the rear of the antenna.
-
7/28/2019 Select and Erect Terrestrial Antennas.pdf
16/50
Select and Erect Terrestrial Antennas
Rev Date: 20-Oct-06 - 16 - NSW DET 2006
expressed as a ratio in dB. The gain of the antenna determines the
amount of signal captured by the antenna from the atmosphere.
Front-to-Back Ratio.
The Front-to-Back ratio of an antenna is the ratio of the signalreceived when the back of the antenna is facing the transmitter,
compared to the signal received when the front of the antenna is
facing the transmitter. Front-to-Back ratio is measured in dB; it is a
measure of the antennas ability to reject unwanted reflected signals
being received from the rear. A good (high) front-to-back ratio is
important if you are experiencing problems with ghosting.
Commercial Antennas
Commercial antennas are available to receive VHF/UHF signals in
a variety of forms. Common types are:
Yagi,
Collinear or Phased array, and
Log Periodic.
Yagi
Yagis always comprise reflectors (longest element at the rear), the
driven element or dipole (the element where the connection is
made), and directors (short elements at the front). The more
elements incorporated into the antenna, the more signal received
by the driven element. When fitted with several directors theseantennas are very directional. Yagi antennas are available for use
on VHF and UHF frequencies. UHF Yagi antennas can be
recognised by their short elements usually 140mm to 300mm long.
Some models are combo antennas with VHF and UHF yagis
combined on a single boom (although the interaction of the
antennas does reduce the gain somewhat). These are common in
metropolitan domestic use where both VHF and UHF channels are
required, signal strength is good, and they reduce the installation
cost.
-
7/28/2019 Select and Erect Terrestrial Antennas.pdf
17/50
Select and Erect Terrestrial Antennas
Rev Date: 20-Oct-06 - 17 - NSW DET 2006
Phased Array
A phased array is based on two collinear half wave dipoles
arranged as a pair in phase (so that the signals add together). (The
term collinear means arranged in one line; this means that a
collinear element may comprise several half-wave elements all in
one line.) Phased arrays are available for VHF and UHF bands and
when stacked provide high gain and good anti-ghosting properties.
VHF Yagi UHF Yagi
Combination VHF/UHF Yagi
-
7/28/2019 Select and Erect Terrestrial Antennas.pdf
18/50
Select and Erect Terrestrial Antennas
Rev Date: 20-Oct-06 - 18 - NSW DET 2006
A typical 4 bay phased array is shown below left.
Log Periodic
A log periodic antenna is recognisable by the tapered length of the
elements and the cross connection of the closely spaced dipoles.
The gain of log periodics is relatively low, however they offer
wideband performance and relatively constant gain over the
frequencies they are designed to receive.
A combination VHF-UHF Log Periodic
Log periodics exhibit relatively flat gain and have become popular
for digital TV reception, especially in regional and rural areas. (The
flatness in gain helps ensure good multiplex flatness covered later
in this Learning Object.)
VHF Horizontally PolarisedPhased Array
UHF Vertically Polarised PhasedArray
-
7/28/2019 Select and Erect Terrestrial Antennas.pdf
19/50
Select and Erect Terrestrial Antennas
Rev Date: 20-Oct-06 - 19 - NSW DET 2006
Task 7.2
Ask your Workplace Trainer to demonstrate to you a range of TV
antennas used in your locality. Identify whether they are Yagis,
Phased Arrays, or Log Periodics. Then identify whether they are
VHF, UHF, or combination antennas.
Variations on the Theme
Yagis, phased arrays, and log periodics all have variations that
designers have developed and are marketed by the various
antenna manufacturers. Sometimes the reflector is of a more solid
style, or is angled (as in the corner reflector style).
It can be difficult at times to classify these more unusual designs,
however they will almost always be one of the three basic types
described in this Learning Object.
Corner reflectorCorner reflector UHF Yagi
-
7/28/2019 Select and Erect Terrestrial Antennas.pdf
20/50
Select and Erect Terrestrial Antennas
Rev Date: 20-Oct-06 - 20 - NSW DET 2006
FREE-TO-AIR (FTA) TELEVISION SIGNAL
STANDARDS
There are currently two standards for television broadcasting in
Australia: Analog PAL, and Digital DVB standards.
Analog Television Standards
Analog television has been the regular standard for television
transmission and reception that we have used since TV was
introduced into Australia in 1956. The analog signal was slightly
modified with the addition of colour transmission in 1975.
At the television studio, the luminance signal (black/white level), the
chrominance signal (colour), and the audio signal (stereo FM
sound) are mixed together to make the raw baseband signal. If
you looked at this signal on a spectrum analyser it would look like
the picture shown below:
Important points to note about this analog signal are:
The bandwidth of the total signal is restricted to 7MHz
The Vision Carrier (luminance) is at 1.25MHz
The Sound Carrier (shown here as Stereo Carriers) is
transmitted at a level of13dB less than the Vision Carrier.
Fig. 7.11: 7 MHz Analog TV signal
-
7/28/2019 Select and Erect Terrestrial Antennas.pdf
21/50
Select and Erect Terrestrial Antennas
Rev Date: 20-Oct-06 - 21 - NSW DET 2006
This is the standard for Australia. Other countries have different
standards.
A disadvantage of analog television is that it can suffer from
interference that degrades the picture. An advantage is that even
with a low or poor signal you may still receive an image on the TV
screen, although it will be grainy or lacking in colour quality.
Digital Television Standards
Analog television is being phased out in Australia and replaced by
Digital services.
The baseband signal of digital television looks very different to an
analog signal. It is composed of many individual carriers (6817 in
total) with integral error correction, and the ability to carry extra
services other than just the vision, colour and sound for the TV
picture. It is beyond the scope of this course to explain how the
coded digital signal is generated or converted back to a TV picture.
However you should understand some of the basic characteristics
of the signal. If you looked at this signal on a spectrum analyser itwould look like the picture shown below:
The bandwidth of the signal remains 7MHz. This is the same
bandwidth as an analog signal.
7 MHz Wide
6817 individual carriers(too many to be able to see individually)
Fig 7.12: 7 MHz Digital TV Signal
-
7/28/2019 Select and Erect Terrestrial Antennas.pdf
22/50
Select and Erect Terrestrial Antennas
Rev Date: 20-Oct-06 - 22 - NSW DET 2006
Digital television has the advantage that it produces a virtually
perfect image and sound if the quality of the signal is acceptable.
Poor signal will result in no picture (or sometimes cause freezing of
the picture or pixilation, which is actually an inbuilt feature of the
digital decoder as it tries to maintain something on the screen). A
(potential) disadvantage of digital TV is that you basically either
have a perfect picture or no picture.
Impulse Noise
On an analog picture impulse noise appears as a series of regular
sparkles on the screen. You m ay be familiar with interference that
can appear when kitchen appliances such as electric blenders are
being used. The arcing of the brushes in the motor causes this
interference. Another source of impulse noise is poorly designed
switchmode power supplies in consumer appliances.
Impulse noise can cause dropout of digital TV reception. Well-
shielded components and coaxial cable can help reduce this
problem. If you can see significant impulse noise on an analog
picture it is worthwhile tracking down the source, otherwise
customers are likely to complain about poor digital TV reception.
Digital Cliff
As the signal strength reduces, the effect of the background
electrical noise becomes worse. (This is more correctly known as
the Carrier to Noise Ratio and is covered in more detail later.) On
an analog TV picture we see this as snow (noise) and colour drop
out. However on a digital picture we do not see this degradation in
picture quality the picture simply freezes or presents a blank
screen. The signal level at which this complete loss of picture
occurs is called the digital cliff. Just because you have a
watchable digital picture this does not mean that the signal strength
is adequate. The digital receiver may be operating right on the
threshold of the digital cliff. Anything that introduces m inor signal
loss (e.g. rain) can cause the signal level to fall over the digital cliff.
Digital signals need to be measured with a signal strength meter,
-
7/28/2019 Select and Erect Terrestrial Antennas.pdf
23/50
Select and Erect Terrestrial Antennas
Rev Date: 20-Oct-06 - 23 - NSW DET 2006
just as analog signals do, to ensure satisfactory long-term
performance.
Experiment:
Your Workplace Trainer may demonstrate the Digital Cliff Effect toyou if the necessary equipment is available at your site.
Radio Frequency
Both analog and digital TV signals are upconverted to higher
frequencies so that a number of TV signals can be transmitted
simultaneously. In Australia, free-to-air (FTA) TV can be
transmitted at frequencies ranging from 45MHz through to
820MHz.
Radio Frequency (RF) signals behave very differently to direct
current or 50Hz AC. W hat may appear to be a short circuit at DC
can behave very differently at RF. Tight bends in coaxial cable can
act as inductors and capacitors, degrading the signal. Poorly
shielded components become transmitters, causing further signal
loss.
Because UHF Bands are increasingly being used for free-to-air TVin Australia it is important that you learn and follow the principles
contained in this Learning Object and the companion learning
Fig 4.13:
-
7/28/2019 Select and Erect Terrestrial Antennas.pdf
24/50
Select and Erect Terrestrial Antennas
Rev Date: 20-Oct-06 - 24 - NSW DET 2006
materials if you are to ensure a trouble-free high quality TV antenna
installation.
Frequencies between 30MHz and 300MHz are known as Very High
Frequencies (VHF). These are TV Bands I, II and III, and TVantennas for these Bands are relatively large, with long elements.
Frequencies between 300MHz and 3,000MHz (3GHz) are known as
Ultra High Frequency (UHF). These are TV bands IV and V, and
TV antennas for these Bands have short elements (although they
may have long booms in order to maximise the signal received).
TV Bands and Frequencies in Australia
The following table may assist you in your role as a TV antenna
installer.
Channel No. Vision MHz Sound MHz Freq Limits(MHz)
DigitalCentre Freq
Band I
0 46.25 51.75 45 - 52 -
1 57.25 62.75 56 - 63 -
2 64.25 69.75 63 - 70 -Band II
3 86.25 91.75 85 - 92 -
4 95.25 100.75 94 - 101 -
5 102.25 107.75 101 - 108 -Out-of-Band
5a 138.25 143.75 137 - 144 -Band III
6 175.25 180.75 174 - 181 177.507 182.25 187.75 181 - 188 184.50
8 189.25 194.75 188 - 195 191.50
9 196.25 201.75 195 - 202 198.50
9a digital - - 202 - 209 205.50
10 analog 209.25 214.75 208 - 215 -10 digital - - 209 - 216 212.50
11 analog 216.25 221.75 215 - 222 -
11 digital 216 - 223 219.50
12 analog 223.25 228.75 222 - 229 -
12 digital - - 223 - 230 226.50
-
7/28/2019 Select and Erect Terrestrial Antennas.pdf
25/50
Select and Erect Terrestrial Antennas
Rev Date: 20-Oct-06 - 25 - NSW DET 2006
Channel No. Vision MHz Sound MHz Freq Limits(MHz)
DigitalCentre Freq
Band IV
28 527.25 532.75 526 - 533 529.5029 534.25 539.75 533 - 540 536.5030 541.25 546.75 540 - 547 543.50
31 548.25 553.75 547 - 554 550.50
32 555.25 560.75 554 - 561 557.50
33 562.25 567.75 561 - 568 564.50
34 569.25 574.75 568 - 575 571.5035 576.25 581.75 575 - 582 578.50
36 583.25 588.75 582 - 589 585.50
37 590.25 595.75 589 - 596 592.50
38 597.25 602.75 596 - 603 599.50
(Band V39 604.25 609.75 603 - 610 606.50
40 611.25 616.75 610 - 617 613.50
41 618.25 623.75 617 - 624 620.50
42 625.25 630.75 624 - 631 627.5043 632.25 637.75 631 - 638 634.50
44 639.25 644.75 638 - 645 641.50
45 646.25 651.75 645 - 652 648.50
46 653.25 658.75 652 - 659 655.50
47 660.25 665.75 659 - 666 662.50
48 667.25 672.75 666 - 673 669.5049 674.25 679.75 673 - 680 676.50
50 681.25 686.75 680 - 687 683.50
51 688.25 693.75 687 - 694 690.50
52 695.25 700.75 694 - 701 697.5053 702.25 707.75 701 - 708 704.50
54 709.25 714.75 708 - 715 711.50
55 716.25 721.75 715 - 722 718.50
56 723.25 728.75 722 - 729 725.5057 730.25 735.75 729 - 736 732.50
58 737.25 742.75 736 - 743 739.50
59 744.25 749.75 743 - 750 746.50
60 751.25 756.75 750 - 757 753.50
61 758.25 763.75 757 - 764 760.5062 765.25 770.75 764 - 771 767.50
63 772.25 777.75 771 - 778 774.50
64 779.25 784.75 778 - 785 781.50
65 786.25 791.75 785 - 792 788.50
66 793.25 798.75 792 - 799 795.5067 800.25 805.75 799 - 806 802.50
68 807.25 812.75 806 - 813 809.50
69 814.25 819.75 813 - 820 816.50
-
7/28/2019 Select and Erect Terrestrial Antennas.pdf
26/50
Select and Erect Terrestrial Antennas
Rev Date: 20-Oct-06 - 26 - NSW DET 2006
Digital Compatibility with Analog Installations
In the capital city areas the digital channels are being allocated next
to the existing analog channels. For example, Ch9 analog is
broadcast on Ch8 digital. Therefore, in this case, a well designedand installed antenna and distribution system will work for digital if it
works for analog. (N.B. The ABC is being transmitted on CH12
digital in most capital cities, so the existing antenna must have a
bandwidth wide enough to receive this channel.)
In rural and regional areas the new digital
channels may not necessarily be in the
same band or even transmitted from the
same location. The website for Digital
Broadcasting Australia (DBA) [www.dba.org.au] can provide details
of the frequencies and transmitter locations for digital broadcast
channels.
The introduction of digital television into your area may require an
upgrade of the customers existing TV antenna installation. Many
older antenna and distribution systems will require upgrading due to
poor cable quality, poor connections, and low quality distribution
components. Good installations deliver a quality signal to the digital
decoder, which should ensure trouble-free viewing.
Signal Strength Levels and Attenuation (dBV anddBs)
It is common practice in telecommunications to use logarithmic
numbers to simplify calculations of signal strength. This practice
has also been adopted in the allied industry of television
transmission and reception.
A Bit of Mathematics
Logarithms are handy because we can use addition and subtraction
to make calculations (rather than multiplication and division if the
numbers are expressed as their true value). dBs are a logarithmic
ratio.
-
7/28/2019 Select and Erect Terrestrial Antennas.pdf
27/50
Select and Erect Terrestrial Antennas
Rev Date: 20-Oct-06 - 27 - NSW DET 2006
dBs for Voltage
In the TV industry we use a logarithmic ratio of voltage because the
power levels are so small. The formula for calculating dBs when
working with voltage ratios is:
x dB = 20 logVin
Vo
In the following example we have an amplifier, with the voltages
shown at its input and output. W e can calculate the gain of the
amplifier.
In the next example we have a circuit that has an attenuator in the
line (it could be a length of coaxial cable). When we measure the
input and output voltages we calculate a loss of 6dB.
Exercise 7.3
Calculate the gain in dB of the following systems:
300 V input, 2 mV output = ? .dB
5mV input, 2 mV output = ? ..dB
You will need a calculator with a logarithm function to answer thesequestions. There is a scientific calculator available in MicrosoftWindows if you need one.
0.1 mV 2 mV
20 log (2 mV 0.1mV) = 26dB gain
1 mV 500 V
20 log (500V 1mV) = - 6dB gain
or 6 dB loss
-
7/28/2019 Select and Erect Terrestrial Antennas.pdf
28/50
Select and Erect Terrestrial Antennas
Rev Date: 20-Oct-06 - 28 - NSW DET 2006
For interest only:
When working with power, the formula for calculating dBs is
different. It is: x dB = 10 log PinPo
Regardless of whether working with voltages or power, the gain (or
loss) still gives the same value in dB.
Adding and Subtracting Gains
When we have a distribution system, such as a TV antenna
distribution network made up of:
o Antenna with gain
o Masthead amplifier with gain
o Cable with loss
o Splitters with loss
o Other active and passive devices,
we can easily just add and subtract the gains of the component that
make up the network.
Fig 7.14: Example of calculating gain in a system.
This is why using dBs is preferable to using actual values the
calculations become simple arithmetic.
Gain = 10 + 20 -8 -4 = 18dB
-
7/28/2019 Select and Erect Terrestrial Antennas.pdf
29/50
Select and Erect Terrestrial Antennas
Rev Date: 20-Oct-06 - 29 - NSW DET 2006
dBV
By referencing the actual voltage back to 1 microvolt we can
continue to use numbers that are easily added and subtracted.
1 millivolt (the minimum analogue signal at the wall plate) is now
known as 60dBV.
20 log (1000V 1V) = 60dBV
Signal level meters give readouts as dBVs. Addition and
subtraction is used to calculate the signal levels throughout our
installation if we know the losses and gains of our components in
the installation.
For example, if we have a system such as shown in Fig 7.15, and
we are receiving a signal of 45dBV out of the antenna, we can
calculate the signal level at the output from the splitter.
Fig 7.15: An example of gains and losses in an antenna distribution system.
Output of splitter = 45dBV + 20dB -8dB -4dB = 53dBV, which isinsufficient to drive a TV receiver (needs minimum 60dBV).
-
7/28/2019 Select and Erect Terrestrial Antennas.pdf
30/50
Select and Erect Terrestrial Antennas
Rev Date: 20-Oct-06 - 30 - NSW DET 2006
Exercise 7.4
Calculate the output signal level for the following system:
Output signal level = .dbV. Is this level sufficient to
drive a TV receiver? Yes / No
(This topic of calculating signal levels in a system is covered further
in the Learning Module: Master Distribution Systems.)
-
7/28/2019 Select and Erect Terrestrial Antennas.pdf
31/50
Select and Erect Terrestrial Antennas
Rev Date: 20-Oct-06 - 31 - NSW DET 2006
Carrier to Noise Ratio
Signal strength is not the only parameter that will ensure a good
picture (whether analog or digital). Just as important is the concept
known as carrier to noise ratio (sometimes abbreviated to CNR).
Electrical Noise
All electrical components (both active and passive devices,
including coaxial cables) produce a wide spectrum of random
electrical noise. If you fully turn up the volume control on an audio
amplifier with no signal being fed in you will hear a hiss. We call
this white noise, because it is equally distributed across all
frequencies, just as white light is made up of all frequencies at
once. This electrical noise extends right through into the radio
frequency spectrum, and if our desired signal is small it can be
swamped by the noise.
C/N ratio
Some other texts on this topic use the term Signal to Noise Ratio.
For our purposes you can consider them to be the same, although
strictly speaking there is a difference. (Because the signal is RF it
is more appropriate to think in terms of the carrier power, hence
CNR.)
In an analog transmission we are measuring the vision carrier.
Most modern signal level meters allow a channel to be directly
selected and will automatically tune to the vision carrier when
performing CNR measurements. Older meters and spectrumanalysers may need to be tuned to the frequency, and hence the
use of the Frequency Allocation Tables included earlier in this
Learning Object.
Digital transmission actually measures the average sum of the
power across all the 6817 carriers.
Noise Power in a Distribution SystemYou can never achieve a better CNR than that received at the
antenna. Using masthead or distribution amplifiers will not improve
-
7/28/2019 Select and Erect Terrestrial Antennas.pdf
32/50
Select and Erect Terrestrial Antennas
Rev Date: 20-Oct-06 - 32 - NSW DET 2006
the CNR, even though the signal strength may increase. This is a
common mistake made by novice antenna installers; thinking that
an amplifier will solve low received signal strength problems.
It is also the reason why received signals are amplified as close aspossible to the antenna. A clean signal that is amplified will swamp
any noise introduced further downline. However, if a signal is
amplified too far down the distribution chain e.g. just before the TV
receiver, the CNR will be already degraded by electrical noise
introduced by the cable, splitters or other passive devices, and
amplification will not be able to improve the CNR.
CNR for Analog and Digital Transmission
Analog television requires a minimum CNR of 48dB for an
acceptable picture.
Digital television requires a minimum CNR of 34dB to ensure that
it is sufficiently far away from the digital cliff.
Free Air Attenuation
The greater the distance between the transmitter and the receiving
antenna the less signal that will be received. Each time the
distance from the transmitter is doubled the power received by the
antenna is reduced by , or -6dB.
In fringe areas (especially rural areas) this can be compensated for
by doubling the height of the tower, which theoretically increases
the signal by 6dB, however in practice it will be less.
Other Causes of Free Air Signal Attenuation
VHF and UHF signals essentially travel in line-of-sight. Any
obstructions between the transmitter and the receiving antenna will
reduce the signal strength level. Obstructions can include
undulating ground, skyscrapers or trees.
-
7/28/2019 Select and Erect Terrestrial Antennas.pdf
33/50
Select and Erect Terrestrial Antennas
Rev Date: 20-Oct-06 - 33 - NSW DET 2006
Case Study 7.1
The owners of an apartment block in the Eastern Suburbs ofSydney had noticed that their analog TV reception had degradedover a number of years, to the point where it was unwatchable. Thecause was a very large eucalyptus tree planted as a seedling a fewyears earlier, and which had grown up directly in the path of thesignal.
Day-Night Fade can cause as much as 3dB change in signal level.
Rain Fade can also result in 3dB change in signal level.
(The addition of these two types of attenuation is the reason why
sometimes you will see a figure of 66dBV quoted for the level at
the outlet plate (or even rounded off to 65dBV), and other times
60dBV. It is the margin that is allowed for attenuation, because
ideally we want a minimum of 1mV [60 dBV] signal at the
receiver.)
-
7/28/2019 Select and Erect Terrestrial Antennas.pdf
34/50
Select and Erect Terrestrial Antennas
Rev Date: 20-Oct-06 - 34 - NSW DET 2006
Required Signal Level at Antenna
[Measuring signal levels requires the use of a signal level meter.
This is covered in the Learning Object: RF Signal Testing.]
The critical factor that will determine a high quality viewable picture
is the signal level received at the antenna for the channel of
interest. Do not be fooled into believing that a low level signal can
be boosted by an amplifier, because when you do this you also
boost the noise in the signal, which still results in a degraded
picture. (See the previous topic on Carrier to Noise Ratio.)
Analog Signal Levels
Ideally you need 65dBV of signal or better at the output of the
antenna. (This will provide a minimum 45dB carrier/noise ratio
resulting in a virtually perfect picture so long as the distribution
system is correctly designed.) The absolute minimum signal level
should be 60dBV. In an analog TV signal this is actually the
signal level of the vision carrier. Some older signal strength metersmay need to be manually set to the required frequency, and for this
purpose the table included in this Learning Object showing TV
channel numbering and associated vision carrier frequency can be
used.
A/V Ratio
Looking at the 7MHz analog TV spectrum (refer to diagram on page
17) you will see that the audio carrier is transmitted at 13dB down
from the level of the vision carrier. This is a fixed value, and most
signal strength meters will measure this A/V ratio. If the value is
anything other than13dB it can indicate ghosting problems.
Digital Signal Levels
To minimise adjacent channel interference, the digital TV signal (in
Australia) is transmitted at 6dB less than analog TV signals. The
specification is for54dBV or better signal strength for the specifiedchannel at the outlet plate.
-
7/28/2019 Select and Erect Terrestrial Antennas.pdf
35/50
Select and Erect Terrestrial Antennas
Rev Date: 20-Oct-06 - 35 - NSW DET 2006
Bit Error Ratio (BER)
A second common measurement you may make with a digital
signal strength meter is the bit error ratio (BER). This should be
less than one error in a million, which is usually shown as 106. If
the signal strength is at least 54dBV then typically the BER will be
acceptable.
Most meters simply approximate the BER from the signal strength
level. As an installer you do not need to be overly concerned with
BER; if you have sufficient signal with a good CNR then the BER
will look after itself.
Mulitplex Flatness
This is a measure of how much difference in level there is across
the 6817 carriers in the 7MHz digital signal. There must be no
more than than 5dB variation. Some digital signal strength meters
will measure multiplex flatness, abbreviated to MFlat.
Fig 7.16: Example of Spectrum for a Digital Channel showing variation in Digital
Carriers.
You probably cant do too much about the quality of multiplex
flatness received at the antenna. However, if multiplex flatness is
acceptable at the antenna, but out-of-specification at the wall plate
then it is an indication of a poorly installed distribution system.
Multiplex flatness problems result in poor BER, and loss of digital
picture (despite having adequate signal and good CNR).
7 MHz Wide
6817 individual carriers
5dB
-
7/28/2019 Select and Erect Terrestrial Antennas.pdf
36/50
Select and Erect Terrestrial Antennas
Rev Date: 20-Oct-06 - 36 - NSW DET 2006
Summary of Required TV Signal Factors
Analog
Signal Level = 60dBV (minimum allow 6dB more for
fading)
CNR = 48dB
A/V Ratio = 13dB
Digital
Signal Level = 54dBV (minimum preferable to aim for 57
58 dBV better
CNR = 34dB
BER = 106
MFlat = 5dB
-
7/28/2019 Select and Erect Terrestrial Antennas.pdf
37/50
Select and Erect Terrestrial Antennas
Rev Date: 20-Oct-06 - 37 - NSW DET 2006
Baluns
At the antenna connection point it is necessary to correctly match
the coaxial cable (which is 75 ohms impedance) to the antenna
folded dipole (also called the driven element, which is 300 ohms
impedance). This matching is done through a special type of RF
transformer known as a balun (which is a combination of the two
words Balanced and Unbalanced).
If you do not use a balun, a mismatch will occur, resulting in
significant loss of signal and multiplex flatness problems. Good
quality Baluns are of the printed circuit board style, with F-connector
outputs and protective UV stabilised ABS plastic casing. It is
recommended that you do not use the cheaper styles of balun
commonly available at hardware stores and electronics shops (see
examples below) as the insertion losses in these can be very high,
and the life expectancy is low due to weathering problems.
Example of a high quality F-connector balun attached
to a UHF dipole.
-
7/28/2019 Select and Erect Terrestrial Antennas.pdf
38/50
Select and Erect Terrestrial Antennas
Rev Date: 20-Oct-06 - 38 - NSW DET 2006
Combining Antennas
In some regional and rural areas it is necessary to use a number of
antennas pointing in different directions to pick up the range of
channels available. Even in city areas the terrain m ay require a
number of antennas pointing in different directions to receive all
channels. (The Northern Beaches region in Sydney is an example
where this is a common practice.) The gain from a combination
VHF/UHF antenna may be insufficient, requiring separate VHF and
UHF antennas.
You cannot simply parallel connect antennas together. If you doyou will cause ghosting problems and mismatch (resulting in signal
loss). You must use a device called a diplexer (or a triplexer if
three antennas are combined together). (Diplexers should also be
of high quality with F-connectors.)
Fig 7.17: Diplexer used to combine a VHF and UHF antenna.
Diplexers filter the desired channels before joining them together at
the output. There are different models available depending upon
the channels that are received at the location and the choice of
band antenna used. If you have a complex antenna installation
(such as in rural and regional areas) then you are advised to
contact the technical support staff at your antenna distributor foradvice regarding the appropriate selection.
-
7/28/2019 Select and Erect Terrestrial Antennas.pdf
39/50
Select and Erect Terrestrial Antennas
Rev Date: 20-Oct-06 - 39 - NSW DET 2006
It is common for separate VHF and UHF antennas to be installed at
a location. In this case a diplexer is used that has an input for
channels 0-12 and a separate input for channels 28-69.
Some models of masthead amplifier have the diplexer integrated
into the design. This will be covered in more detail in the Learning
Object Master Distribution Systems.
Task 7.5
Ask your Workplace Trainer to show you the range of diplexers
commonly used in your region of installations and operation.
Antenna Separation
When you are mounting multiple antennas there needs to be some
physical separation between them so as to avoid having the
metalwork of one antenna electrically interact with another. When
mounting multiple antennas, the UHF antenna should be mounted
at the top of the mast. The minimum distance to keep antennas
separated is 600mm, however the greater the distance that can be
achieved the better.
Example of a diplexer used
in a domestic application.
-
7/28/2019 Select and Erect Terrestrial Antennas.pdf
40/50
Select and Erect Terrestrial Antennas
Rev Date: 20-Oct-06 - 40 - NSW DET 2006
Example of a correctly mounted
VHF vertical polarised phasedarray mounted above a UHF
vertical polarised phased array.
Another example of a correctly
stacked mast, with a UHF vertical
polarised Yagi mounted above a
VHF vertical polarised phased
array.
Incorrect example. The UHF
antenna is lower than the VHF
antenna. (This may be
acceptable if you are receiving a
local UHF and distant VHF
signal.)
-
7/28/2019 Select and Erect Terrestrial Antennas.pdf
41/50
Select and Erect Terrestrial Antennas
Rev Date: 20-Oct-06 - 41 - NSW DET 2006
Increasing Gain
It is possible to increase the signal strength by combining the
signals received from two similar antennas. This is beyond the
scope of this learning object, however it is an option worth
considering if you are struggling to achieve the required signal
strength. The two signals need to be phased together so that the
signals add together (out-of-phase signals will actually give you less
signal than a single antenna) and this requires careful engineering
design.
A poor installation, where the
antennas are far too close
together, causing interaction, loss
of signal strength, and ghosting
(due to poor front-to-back ratio).
To achieve the required
separation you might
prefer to use separate
masts.
-
7/28/2019 Select and Erect Terrestrial Antennas.pdf
42/50
Select and Erect Terrestrial Antennas
Rev Date: 20-Oct-06 - 42 - NSW DET 2006
Here are examples of yagis phased together to increase the gain
Task 7.6
As you move around your area look for masts that have combined
antennas, and identify correctly and incorrectly installed systems.
Write down the locations and the problems in your notebook.
Site Survey
In order to determine the best location to erect the antenna at the
customers premises you will likely need to conduct a site survey.
This will also tell you how much signal is available at the location,
and therefore the gain requirements for the antenna you select to
use. The signal strength will vary greatly as you move around
different points on the roof, and the site survey will also help
determine the optimum location for the antenna.
When choosing a final location for the antenna consider:
The need to keep 3 metres away from aerial power line feeders.
Access for coaxial cable to enter the premises.
The cost of mounting hardware. (For example, theres little point
struggling for an extra 2dB in a difficult to mount location if an
antenna with more gain will do the job.)
Reference AntennaThe reference antenna you use needs to be appropriate for the TV
channel you are interested in. It should be of a manageable size for
-
7/28/2019 Select and Erect Terrestrial Antennas.pdf
43/50
Select and Erect Terrestrial Antennas
Rev Date: 20-Oct-06 - 43 - NSW DET 2006
you to use safely at heights. You also need to know the gain of the
antenna at the required frequency so that you calculate the required
gain of the antenna to be installed.
The major TV antenna manufacturers can recommend suitableantennas for use as reference antennas.
A test reference antenna needs to have broad bandwidth (covering
all the required channels) and be
physically small enough to use safely
when working at heights. The
characteristics of the log periodic
tend to make it suitable for this
purpose.
Example:
You need to set up an antenna to receive Ch 8 in a rural area of
New South Wales. The test antenna you are using has a gain of
5dB on Band III. The highest signal level you measure as you
move about the roof is 58dBV. You need 65dBV. Therefore youneed an antenna with at least 7dB more than your test antenna,
that is, a gain of better than 12dB (5dB + 7dB).
Watch DVD
Watch Chapter 2 to see a technician conducting a site survey.
Fig 4.18: Log periodic test antenna.
-
7/28/2019 Select and Erect Terrestrial Antennas.pdf
44/50
Select and Erect Terrestrial Antennas
Rev Date: 20-Oct-06 - 44 - NSW DET 2006
Task 7.7
Assuming you want 65dbV out of the antenna, calculate the gain
of antenna required if these are the site survey results you
measure:
Required Channel: 28
Band IV Test Antenna Gain: 8dB
Measured Ch28 Signal Strength out of antenna: 59dBV
Required gain of antenna: _____ dB
Task 7.8
Under the supervision of your workplace trainer, conduct a site
survey for an antenna installation at a customers premises, or at
any site suitable for this purpose. Recommend a suitable antenna/s
to receive the TV channels for your area.
-
7/28/2019 Select and Erect Terrestrial Antennas.pdf
45/50
Select and Erect Terrestrial Antennas
Rev Date: 20-Oct-06 - 45 - NSW DET 2006
Conclusion
A well designed and installed antenna system will provide a clean
signal of sufficient strength to drive the distribution system for the
premises or location you have been contracted to service. The use
of quality components will provide trouble free operation for many
years. Short-cuts and cheap components may provide some
reduction in initial equipment costs or labour time, however in the
longer term it will cause warranty callouts and damage to your
reputation as a TV antenna installer.
A very poorly installed antenna system!
-
7/28/2019 Select and Erect Terrestrial Antennas.pdf
46/50
Select and Erect Terrestrial Antennas
Rev Date: 20-Oct-06 - 46 - NSW DET 2006
SELF ASSESSMENT
The following set of questions will assist you to determine whether you
have learnt and understood the content of this Learning Object. Your
Workplace Assessor may ask questions that are different from those here.
Circle the correct answer.
1. The bandwidth of a TV channel is:
a) 1MHz
b) 5MHz
c) 7 MHz
d) Varies depending upon the frequency of the transmission.
2. In an analog system the vision carrier is:
a) 0.5 MHz above the bottom lowest frequency of the allocated bandwidth
b) 1.25 MHz above the bottom lowest frequency of the allocated bandwidth
c) in the middle of the allocated bandwidth for the Channel
d) at the uppermost frequency allocated for the Channel bandwidth.
3. The channel bandwidth for digital television is:
a) greater than for analog television
b) the same as for analog television
c) much more than for analog television
4. Comparing analog and digital television: (circle all correct answers)
a) a digital TV picture will almost always be of higher quality than an analog
picture.
b) in areas where ghosting is a problem, digital television provides a goodsolution.
c) you will always need to install a new TV antenna and distribution systemif your customer requires digital television reception.
d) if you can see a good picture on a digital TV receiver you have a goodquality TV antenna installation.
5. What is the upper and lower frequency range of free-to-air television
transmissions in Australia?
-
7/28/2019 Select and Erect Terrestrial Antennas.pdf
47/50
Select and Erect Terrestrial Antennas
Rev Date: 20-Oct-06 - 47 - NSW DET 2006
6. What difference would we notice between an antenna designed for Band III and
an antenna designed for Band IV?
7. What are the minimum signal strengths for analog and digital reception that you
require at the TV antenna wall plate (in dBV) to ensure good quality pictures?
8. Ghosting is caused by:
a) excessive signal entering the TV tuner.
b) the TV signal bouncing off the ionosphere.
c) faulty components inside the TV receiver
d) multipathing (reflections) of the TV signal off buildings, mountains, and
other such structures.
9. TV signals essentially travel in line-of-sight. True / False
10. It doesnt matter if a TV antenna is installed with its elements horizontal orvertical. True / False. Explain why.
11. The name of the device that combines multiple antennas together is:
a) a tap
b) a diplexer
c) a filter
d) a splitter
12. A balun is only necessary if you are in a fringe area with poor signal strength.
True / False?13. What is the wavelength of Ch 2? (Show your calculations.)
14. What is the impedance of a folded dipole? How is the antenna impedance
matched to the impedance of the coaxial cable in order to minimise signal loss?
-
7/28/2019 Select and Erect Terrestrial Antennas.pdf
48/50
Select and Erect Terrestrial Antennas
Rev Date: 20-Oct-06 - 48 - NSW DET 2006
15. What addition is made to a simple dipole to make a directional antenna with
gain?
16. Name three types of TV antenna design.
17. When mounting a UHF and VHF antenna on the same mast what is therecommended minimum separation distance, and which antenna should go atthe top of the mast?
18. Calculate the dB gain (or loss) for the following systems:-
a) Vin = 300V and Vout 2mV
b) Vin = 10mV and Vout 0.5mV
19. In the following network there is 55dBV into the amplifier. What level of signal
will appear out of the splitter? ..dBV
Signal In =
55dBV
Cable loss = 10dB
Splitter loss = 8.5dB
G = 8dB
-
7/28/2019 Select and Erect Terrestrial Antennas.pdf
49/50
Select and Erect Terrestrial Antennas
Rev Date: 20-Oct-06 - 49 - NSW DET 2006
Answers t o S elf Assessment Questions
1. (c)
2. (b)
3. (b)
4. (a), (b). You may not need to install a new TV antenna and distribution
system for digital television if the previous installation is within
specifications. A digital TV picture may be received even with a poor
installation, however the problem is that it may be very close to the digital
cliff, and any further minor degradation in signal could cause total loss of
picture.
5. 45MHz to 820MHz.
6. Band III is VHF, requiring a VHF antenna, recognised by its longer
elements. Band IV is UHF, requiring a UHF antenna, recognised by its
shorter elements.
7. Analog = 60dBV; Digital = 54dBV. (These are regarded as absolute
minimums, and it is recommended that 3 6 dB more should be the
adopted practice.)
8. (d)
9. True
10. False. A TV antenna must be installed with the same polarisation as the
transmitted signal.
11. (b)
12. False.
13. 300 divided by 64.25 = 4.67 metres wavelength.
14. 300. Baluns are required to change the 300 impedance of the folded
dipole to 75 of the coax cable.
-
7/28/2019 Select and Erect Terrestrial Antennas.pdf
50/50
Select and Erect Terrestrial Antennas
15. Reflectors are added and a director, making a Yagi antenna.
16. Yagi, Phased Array, Log Periodic.
17. The recommended minimum distance between two antennas is 600mm.
The UHF antenna should be mounted above the VHF antenna.
18. (a) 20 log (2 / 0.3) = 16.5dB (b) 20 log (0.5 / 10) = -26dB
19. 55dBV + 8dB -10dB -8.5dB = 44.5dBV