seed rate charts - great plains ag · 401-312b 12/02/2009 setting meter rate hydraulic drive meter...

© Copyright 2009 Printed 12/02/2009 401-312B

Manufacturing, Inc.www.greatplainsmfg.com

Seed Rate Charts forthe 3PYP PlanterThe following pages are to assist in the proper setting of seeding and fertil-izer rates for the 3PYP 40ft 3-point planter. The volumetric rates indicated inthe charts are approximate values. To assure the most accurate seedingrate it is recommended that the planter and meters be calibrated for thedesired seed at the time of planting.

http://www.greatplainsmfg.com

Great Plains Mfg., Inc.

401-312B 12/02/2009

Table of Contents

© Copyright 2007, 2008, 2009. All rights Reserved

Great Plains Manufacturing, Inc. provides this publication “as is” without warranty of any kind, either expressed or implied. While every precaution has been taken in the prepa-ration of this manual, Great Plains Manufacturing, Inc. assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use ofthe information contained herein. Great Plains Manufacturing, Inc. reserves the right to revise and improve its products as it sees fit. This publication describes the state of thisproduct at the time of its publication, and may not reflect the product in the future.

Great Plains Manufacturing, Incorporated TrademarksThe following are trademarks of Great Plains Mfg., Inc.: Application Systems, Ausherman, Land Pride, Great Plains

All other brands and product names are trademarks or registered trademarks of their respective holders.

Printed in the United States of America.

Planting Rate .............................................................. 1Setting Planting Rate ............................................... 1Setting Fertilizer Rate .............................................. 1

Setting Meter Rate ..................................................... 2Hydraulic Drive Meter Rate...................................... 2Ground Drive Meter Rate......................................... 2

Gauge Wheel Sprocket Selection ........................ 2For All Ground Drive Adjustments.................... 3Drive Range Sprockets .................................... 3Transmission Sprockets ................................... 4Upper Drive Sprockets ..................................... 4

Checking Planting Rate ........................................... 5Checking Singulated Rate.................................... 5

Seed Rate Check Sample Size ........................ 5Seed Rate Check Examples ............................ 5

Checking Volumetric Rate.................................... 6Checking Volumetric Ground Drive .................. 6Checking Volumetric Hydraulic Drive ............... 7

Finger Meter Planting ................................................ 8Reading a Finger Meter Rate Chart ......................... 8

Hydraulic or Ground Drive.................................... 8Ground Drive........................................................ 8

Finger Meter Adjustments........................................ 9Finger Meter Brush Adjustment ........................... 9

Finger Meter Inserts ....................................... 1020in Single Row, 6-Finger...................................... 1120in Single Row, 12-Finger.................................... 1230in Single Row, 6-Finger...................................... 1330in Single Row, 12-Finger.................................... 1430in Twin Row, 6-Finger ........................................ 1530in Twin Row, 12-Finger ...................................... 1636in Single Row, 6-Finger...................................... 1836in Single Row, 12-Finger.................................... 1936in Twin Row, 6-Finger ........................................ 2036in Twin Row, 12-Finger ...................................... 2138in Single Row, 6-Finger...................................... 2338in Single Row, 12-Finger.................................... 2438in Twin Row, 6-Finger ........................................ 2538in Twin Row, 12-Finger ...................................... 2640in Single Row, 6-Finger...................................... 28

40in Single Row, 12-Finger.................................... 2940in Twin Row, 6-Finger ........................................ 3040in Twin Row, 12-Finger ...................................... 31

Sprocket Indexing (Stagger)................................... 3330in Rows, 6-Finger Indexing ............................ 3430in Rows, 12-Finger Indexing .......................... 3536in Rows, 6-Finger Indexing ............................ 3636in Rows, 12-Finger Indexing .......................... 3738in Rows, 6-Finger Indexing ............................ 3838in Rows, 12-Finger Indexing .......................... 3940in Rows, 6-Finger Indexing ............................ 4040in Rows, 12-Finger Indexing .......................... 41

Indexing Fine Adjustment ...................................... 426-Finger Meter Stagger Adjustment................... 4212-Finger Meter Stagger Adjustment................. 43

Singulating Meter Planting ..................................... 44Reading a Singulated Rate Chart .......................... 44

Hydraulic or Ground Drive ................................. 44Ground Drive...................................................... 44

Corn ....................................................................... 45Cotton .................................................................... 46Milo (51 Cell Meter)................................................ 48Milo (102 Cell Meter).............................................. 50Milo (135 Cell Meter).............................................. 52Milo (270 Cell Meter).............................................. 54Soybeans (100 Cell Meter) .................................... 56Soybeans (110 Cell Meter) .................................... 58

Volumetric Meter Planting ...................................... 60Reading a Volumetric Rate Chart .......................... 60

Hydraulic or Ground Drive ................................. 60Ground Drive...................................................... 60

Wheat, 64lb/bu Hard, Narrow Wheel ..................... 61Wheat, 64lb/bu Hard, Wide Wheel......................... 62Wheat, 62lb/bu Soft, Wide Wheel .......................... 63Wheat, 62lb/bu Soft, V3 Wheel.............................. 64

Fertilizer Rate ........................................................... 65Orifice Plate Selection............................................ 65

Orifice Size Charts ............................................. 66Appendix .................................................................. 67

Seed Lubricants ..................................................... 67

Great Plains Mfg., Inc.1

Planting Rate

This manual is your guide to planter adjustments forachieving specific seed population targets. It alsoincludes information you may need to properly setupand adjust a separately provisioned fertilizer pump sys-tem.

Although some setup/adjustment material herein isrepeated from the Operator’s Manual, you need to bethoroughly familiar with planter operations and adjust-ments before applying this Seed Rate manual and itstable data.

Setting Planting RateThere are 4 to 8 steps to obtaining the desired numberof seeds per acre, some of which apply only to ground-drive planters, certain meter types, and particular rowunit configurations:

1. Know the characteristics of the seed

Consult your seed supplier’s reference documents.

2. Install the correct seed meters and wheels

Consult your Great Plains dealer and see “SeedMeter Setup and Adjustment” in the Operator’sManual.

3. Adjust Finger Pickup meters for the seed

This only applies to finger pickup meters.See “Finger Meter Adjustments” on page 9

4. Sprocket index for staggered twin-row

This only applies to twin-row planters, and then onlyif precise seed spacing is desired between adjacentrows in the twin pair. See “Indexing Fine Adjust-ment” on page 42.

5. Set meter rate

For hydraulic meter drive, this is done via the seedmonitor. Once data about your planter is entered,you select the seed rate directly. Consult the man-ual for the seed monitor.

For ground drive meters, three sprocket sets areconfigured at each gauge wheel:a. rangeb. transmissionc. upper drive

See “Ground Drive Meter Rate” on page 2.

6. Check planting rate

See “Checking Planting Rate” on page 5.

Setting Fertilizer RateIf your planter is equipped with the optional fertilizermanifold system, it does not include the tank and pump-ing system. Rate is primarily controlled by the sepa-rately-provisioned pump (typically tractor-mounted, andservo-controlled by a groundspeed radar), but the ratealso affected by the size of the orifices in the manifold.

Consult the documentation for the pump system onbasic fertilizer flow rate.

See “Fertilizer Rate” on page 65 for orifice information.

12/02/2009 401-312B


Setting Meter Rate

Hydraulic Drive Meter RateHydraulic drive meter rate is set directly on the seedmonitor in the tractor. Consult the monitor manual fordetailed instructions, which may vary over time withfirmware updates to the monitor system.

You will need to enter/update your planter configuration(width/row-count, single-row/twin, meter type, wheel cellcount, etc.). Once entered, you can specify the desiredpopulation directly in seeds per acre.

Although the sprocket information in the Seed RateCharts of this manual does not apply to hydraulic drive,the recommended planting speed (in mph) does apply.

Note: For most consistent results, and least wear onthe meters, check the seed rate chart for the cropor meter type/wheel, and do not exceed the rec-ommended ground speed.

Ground Drive Meter RateOn 3PYP Planters without hydraulic drive, the row unitsare driven by the gauge wheels, in ground drive.

Both left and right gauge wheels include the completedrive train, and left/center/right drive shaft sections areall coupled together via clutches.

Note: Although in an emergency (such as a chainbreak), either gauge wheel can drive the entireplanter, in normal operation both sides are used,and are identically configured.

Gauge Wheel Sprocket SelectionRefer to Figure 1

The ground drive assembly has two sets of threechains that are user adjustable:

1. Range2 of 6 sprockets, stored on shaftsboth driving and driven shafts may adjust

2. Transmission2 of 10 sprockets, stored on vertical spindleboth driving and driven shafts may adjust

3. Upper drive1 of 2 sprockets, selected by spaceronly the driving shaft adjusts

For a specific row-spacing, meter and seed, the start-ing sprocket settings for all three chains are found inthe Seed Rate Charts.

Fine adjustment to planting rate is made by the Trans-mission chain ➁.

Sprocket pairings are identified in the Charts both bysprocket size and by which sprocket is mounted onwhich shaft.

Sprockets are sized by tooth count, stamped on thesprocket.The same shaft can be both a driving anddriven shaft depending on the required combinations.

The DRIVING shaft on any chain is the one closer tothe gauge wheel (lower in the assembly).

The DRIVEN shaft on any chain is the one further fromthe gauge wheel (higher in the assembly).

Figure 1Ground Drive Chains

25259

➀

➂

➁

401-312B 12/02/2009


For All Ground Drive Adjustments

IMPORTANT !The 3PYP Planter must be unfolded, and the tractoror planter parked, before making any of these adjust-ments.

IMPORTANT !Any setup and adjustments must be made identicallyon each of the two gauge wheel drives. If there areany differences, there will be excess clutch wear,and unpredictable seed rate results.

Steps:

1. Raise the planter and install lift-assist cylinder locks.

2. Rotate each gauge wheel. Check that seed meters,seed tubes and drives are working properly and areclear of debris and obstructions.

3. Check tire pressure, per the “Tire Inflation Chart”in the Appendix of the Operator’s Manual.

Drive Range Sprockets1. Obtain the sprocket pairing from the Seed Rate

Chart.

2. Loosen the bolt on the forward idler ➀, and slidethe idler to the bottom of its track.

3. Remove the lynch pins from both the driving ➁,and driven ➂ shafts.

4. Remove the four alternate sprockets, and set themon the toolbar.

5. Remove the chain.

6. Exchange the existing low range sprockets forthose called out in the Seed Rate Chart.

IMPORTANT !Make sure the correct sprockets are mounted on thedriving or driven shafts as called for by the Charts.

7. Store any removed sprockets on their shafts andre-pin.

8. Slide the idler ➀ up, and tighten its bolt, allowing1⁄4in slack in the longest chain span.

Figure 2Lower Range Sprockets

25260

➂

➀

➁

12/02/2009 401-312B


Transmission Sprockets1. Obtain the initial sprocket pairing from the Seed

Rate Chart.


3. Remove the lynch pins from both the driving ➁,and driven ➂ shafts.

4. Remove the chain.

5. As needed, exchange the existing sprocket pair forthe new pair, using alternate sprockets from thevertical storage spindle ➃.

IMPORTANT !Make sure the correct sprockets are mounted on thedriving or driven shafts as called for by the Charts.


7. Store the removed and any loose sprockets on thespindle shaft and re-pin it. Make sure all eightalternative sprockets are accounted for.

Upper Drive Sprockets1. Obtain the driven sprocket selection from the Seed

Rate Chart. Make sure your configuration actuallyneed to be changed.


3. Remove split plastic spacer ➁. It will be to the leftof the smaller (18 tooth) sprocket if the 18T was inuse, and to the right of the larger (36 tooth)sprocket if the 36T was in use.

4. Move the spacer (part number 120-337S) to theother side of the sprocket pair, sliding the sprocketpair ➂ left or right to make room.

5. Lift the chain off the sprocket formerly in use, andmove it to the sprocket to be used.


Figure 3Transmission Sprockets

25262

➁➀

➂

➃

Figure 4Upper Drive Sprockets

25261

➀

➁

➂

401-312B 12/02/2009


Checking Planting RateAlthough your seed monitor will report useful full passresults, cautious practice includes manually checkingthe seed rate early in the first pass.

The seed charts are based on cleaned and sized seed.Extreme seed variations, foreign material and tire pres-sure can materially affect planting rate.

Checking the rate also provides a double-check on yourpopulation calculations and drive configuration.

The procedure is different for singulated and volumetricseeding.

Checking Singulated Rate1. Using the table below, determine the length and

number of rows to check. For twin-row operation, apair of row units counts as one row.

2. Adjust the planting depth to shallow on that numberof rows units. Using center and wing-end row unitsfor measurement provides a more accurate assess-ment of overall planter performance.

3. Use bungees or wire to tie-up the press wheelassembly on the tested row units, so that the seedis not covered. Tie up both in a pair for twin-row.

4. Operate the planter for the distance in the table,plus a few feet for the press wheels to clear the endof the sample distance.

5. Count the number of seeds in the test rows.

6. Multiply the total number of seeds counted by 200 ifmeasuring for 1⁄200 acre, or by 1000 if measuring for1⁄1000 acre. This is the plant population in seeds peracre.

7. If the populated is substantially different thanexpected, check tire inflation, and on a ground-driveplanter, double-check the sprocket configuration.See “Troubleshooting” in Operator’s Manual.

Seed Rate Check Sample Size

Seed Rate Check Examples10in spacing single-row planter:Per the table, plant about 20 ft, measure 17ft 5in, andcount 3 rows for 1⁄1000 acre. 180 seeds are counted:

180 x 1000 = 180,000 seeds per acre

30in spacing twin-row planter:Per the table, plant about 90ft, measure 87ft 1in andcount 2 double rows for 1⁄200 acre. 170 seeds arecounted:

170 x 200 = 34,000 seeds per acre

Rows to Sample Length of Row to Count for

Spacing (in) Number to Count 1⁄1000th Acre 1⁄200th Acre

71⁄2in 4 17ft 5in use 1⁄1000 acre

91⁄2in 3 18ft 4in use 1⁄1000 acre

10 3 17ft 5in use 1⁄1000 acre

15 2 17ft 5in 87ft 1in

19 2 13ft 9in 68ft 9in

20 1 26ft 2in 130ft 8in

30in or Twin 30 1*

*. Twin Rows count as one row.

17ft 5in 87ft 1in

36in or Twin 36 1* 14ft 6in 72ft 7in



15in Skip Row 2 15ft 3in 76ft 3in

12/02/2009 401-312B


Checking Volumetric RateVolumetric seeds are planted at much higher popula-tions than singulated seeds, and are measured inpounds (rather than seeds) per acre. This make the sin-gulated rate check technique impractical.

The process used depends on the meter drive type.

Checking Volumetric Ground DriveUse the following steps to check volumetric rate. Thisprocedure does not work on hydraulic drive planters. Onground drive planters, the ground drive needs to besetup for the target seed rate before conducting the test.

You will need a:

• tire marker (grease pencil, chalk or similar),

• three containers to catch seed as it exits the seedtube on three row units, and

• means of accurately weighing modest quantities ofseed. Read the steps in the procedure and estimatethe sample quantity that is likely.

1. Select three adjacent sampling row units near oneof the ground drive wheels. Make sure at least oneallows observation of the seed exiting the meterwhile manually turning the gauge wheel.

2. Shut off the Y-tubes to all other row units. This pre-vents clogging the lines with seed.

3. If the tractor is connected and providing power tothe planter, use the clutches to disconnect otherplanter sections. This reduces the effort in turningthe gauge wheel.

4. Disengage the drive couplers on all other meters onthe test section, except the meters to be used fortesting. This further reduces the effort in turning thegauge wheel.

5. Raise the planter, and install the lift cylinder trans-port locks. Leave the tractor hydraulic systemactive.

If the planter has hydraulic steering, flip the (fan)override switch to On.

6. Place a collection bucket under each test meter’sseed tube.

7. Mark the right side of the ground drive tire at theyoke arm.

8. Activate the hydraulic circuit for the seed fan.

9. Rotate the gauge wheel a few turns to ensure seedflow and proper meter operation. Stop rotation withthe tire mark again at the mark. Clear the seed col-lection containers and place them back under theseed tubes.

10. Rotate the gauge wheel for one acre:

11. Shut off the fan.

12. Weigh the collected seed.

RowSpacing

Numberof Rows

PassWidth

Turns forOne Acre

15in 31 465in 147.1

20in 23 460in 148.7

30in 16 / 32T 480in 142.5

36in 12 / 24T 432in 158.3

38in 12 / 24T 456in 150.0

40in 12 / 24T 480in 142.5

401-312B 12/02/2009


Checking Volumetric Hydraulic DriveUse the following steps to check volumetric rate. Thisprocedure does not work on ground drive planters. Thetractor will need to be hitched to the planter, and provid-ing electrical and hydraulic power.

1. Configure the seed monitor for the planter and crop(material).

2. Consult the rate chart for seed. Note the “poundsper revolution” figure in the upper left corner.

3. Select at least four adjacent sampling row units onone side of the planter. The more rows sampled, thegreater the confidence in the results.

4. Shut off the Y-tubes to all other row units. This pre-vents clogging the lines with seed.

5. Use the clutches to disconnect the other side (half)of the planter. This eliminates the need to uncouplethe meters on that side.

6. Disengage the drive couplers on all other meters onthe test side, except the meters to be used for test-ing.

7. Raise the planter, and install the lift cylinder trans-port locks. Leave the tractor hydraulic systemactive.

If the planter has hydraulic steering, flip the (fan)override switch to On.

8. Place a collection bucket under each test meter’sseed tube.

9. Command the planter seed monitor to:FILL DISK

10. Command the seed monitor to run the:5 REV TEST

11. Weigh the seed. Compare the result with thatexpected from the Pounds Per Revolution data(assuming 4 rows tested):

Expected PoundsPerRev 5 4××=

12/02/2009 401-312B


Finger Meter Planting

The basic seed rate for finger meters is determined bythe meter finger count (6 or 12), and the drive setup.

Finger meters have two additional adjustments for opti-mum results:

1. Meter brush (see page 9)

2. Twin row indexing (see page 33)

IMPORTANT !Recommended speed is 41⁄2 to 5 miles per hour.

Excess speeds are known to deteriorate seed spacingcontrol and depth control.

Reading a Finger Meter Rate ChartHydraulic or Ground Drive1. Consult the chart for your row spacing and meter

type.

2. Find the desired seed population or seed spacing.

3. Note the range of meter rpms suitable for that popu-lation.

IMPORTANT !The shaded rpms are the recommended rpms formost consistent results. Use the recommended drivingspeed if possible.

With hydraulic meter drive, enter the population in theseed monitor. With ground drive, configure the sprock-ets.

Ground Drive4. Each chart page shows the Range and Upper Drive

sprockets at the upper left.

5. The Transmission sprockets are in the table, foundto the left of the Population.

5 - 1625 20" ROWS d corn types) 6 Finger Meter

p p p p ons Seed Seed

Population Spacing Meter Meter Meter Meter Meiven (seeds/acre) (inches) (rpm) (rpm) (rpm) (rpm) (rp

28 11,996 26.1 4727 12,440 25.2 49 45

16.5 75 69 64 59 53 4816.5 75 69 64 59 53 4815.9 72 67 61 55 5015.3 75 69 63 57 52 415.3 75 69 63 58 52 415.3 75 69 63 58 52 415 2 75 69 64 58 52

Great Plains always recommends test stand calibration of the finger m

Range Sprockets For Round Corn optimum Driver = 30 ( Shaded & Non-shaded Driven = 15Upper Drive Sprocket For Flat Corn optimum m

18 (Shaded area)Ground

Transmission 7 mph 6.5 mph 6 mCombinations Seed Seed

Population Spacing Meter Meter MeDriver Driven (seeds/acre) (inches) (rpm) (rpm) (rp

17 28 11,996 26.1 4717 27 12,440 25.2 49 4517 26 12,918 24.3 51 4719 28 13,407 23.4 53 49 45

401-312B 12/02/2009


Finger Meter AdjustmentsThe finger pick up meter has an adjustable brush. Thebrush has been pre-set to the optimum setting for mostseed sizes.

Finger Meter Brush AdjustmentThe brush reduces or eliminates “doubles” (deliveringtwo seeds per finger), but if set too aggressively cancause “skips” (delivering no seed on some fingers). Asneeded, adjust for minimal doubles and skips.

Note: These instructions describe the current fingerpickup meter shipped with new Great Plainsplanters, which has an integrated adjustment le-ver for the brush. If you have added pre-existingfinger meters after purchase, there is somechance that you may have previous modelmeters, adjusted by screwdriver rather than le-ver. If so, rely on counting detents to determinethe setting. Not all have 9 detents.

Refer to Figure 5

The adjustable brush provides additional flexibility toaccommodate a wide range of seed sizes. Use lever(L) to gently rotate the brush into position.

The settings range from 1 to 5 with detents at each halfstep, for a total of 9 detents. Although the numbers aremolded into the meter housing, only “1” and “5” may bevisible. To ensure consistency, rotate the lever fullycounter-clockwise (1), and count detents as youadvance it to the desired setting.

Use the general guidelines in the table below to adjustthe brush position to your seed size and shape. Thenumbers listed correspond to the numbers printed onthe outer housing of your meter.

If there is a decal on your meter, its units are in poundsper 80,000 seed bag. The table below includes seedsper pound.

Figure 5Finger Meter Brush Lever

25276

5

1

43

2

L

SeedShape

Bag Weight(80,000 seeds)

Seeds PerPound

BrushSetting

flats 35 lbs 2300 or less 2flats 35 lbs 2300 or more 3flats 45 lbs 1780 or less 1flats 45 lbs 1780 or less 2

rounds 35 lbs 2300 or less 4rounds 35 lbs 2300 or more 5rounds 45 lbs 1780 or less 3rounds 45 lbs 1780 or more 4rounds 55 lbs 1450 or more 2rounds 55 lbs 1450 or more 3rounds 65 lbs 1230 or less 1rounds 65 lbs 1230 or more 2

12/02/2009 401-312B


Finger Meter InsertsRefer to Figure

The backing plate is equipped with an “A” insert ➀. Intests, this insert provides the best performance in mostseed sizes. However, there are two alternative insertsthat can be used. Before changing to a different insert,please consult with a Great Plains service representa-tive for a recommendation.

The insert type is molded into the back. Changinginserts requires meter disassembly, and is not furtherdescribed in this manual.

IMPORTANT !Be cautious in using seed treatments, additives, andother chemicals when possible. They can causemeter performance problems and premature wear tometer parts.

Avoid the use of graphite with untreated seeds. Ifgraphite must be used, use Precision™ plantinggraphite or Great Plains graphite which is less abra-sive. Seeds with Maxi, Captan, Cruiser, Poncho andsimilar treatments can benefit from graphite. Use theamount recommended on the graphite container,usually 1 tsp/unit or 1 tsp/80,000#.

Always store meters in a dry, secure place, withbrush in between two meter fingers. Moisture, tem-perature, nest-building insects and rodents can cre-ate problems.

Always pay attention to your seed monitor and oper-ating manual. Monitor the amount of seed you areplanting compared to your expectations. Alwaysinvestigate abnormalities!

Figure 6Finger Meter Insert

22908

401-312B 12/02/2009


20in Single Row, 6-Finger

3PT YIELD PRO 1225 - 1625 20" ROWSATTENTION ! ! ! (For all seed corn types) 6 Finger MeterGreat Plains always recommends test stand calibration of the finger meter to the population and ground speed desired

Range Sprockets For Round Corn optimum meter speed is 45 to 75 RPMDriver = 30 ( Shaded & Non-shaded areas )Driven = 15Upper Drive Sprocket For Flat Corn optimum meter speed is 60 to 75 RPM

18 (Shaded area)Ground Speed

Transmission 7 mph 6.5 mph 6 mph 5.5 mph 5 mph 4.5 mph 4 mph 3.5 mphCombinations Seed Seed

Population Spacing Meter Meter Meter Meter Meter Meter Meter MeterDriver Driven (seeds/acre) (inches) (rpm) (rpm) (rpm) (rpm) (rpm) (rpm) (rpm) (rpm)

17 28 11,996 26.1 4717 27 12,440 25 2 49 4517 26 12,918 24 3 51 4719 28 13,407 23.4 53 49 4517 25 13,435 23 3 53 49 45 Not Recommended19 27 13,904 22 6 55 51 4717 24 13,995 22.4 55 51 4719 26 14,438 21.7 57 53 49 4517 23 14,603 21 5 57 53 49 4519 25 15,016 20 9 59 55 51 4619 24 15,641 20.1 61 57 53 4823 28 16,229 19 3 64 59 55 50 4619 23 16,322 19 2 64 60 55 50 4623 27 16,831 18 6 66 61 57 52 4724 28 16,935 18 5 67 62 57 52 4823 26 17,478 17 9 69 64 59 54 4924 27 17,562 17 9 69 64 59 54 4925 28 17,641 17 8 69 64 59 54 49 4517 19 17,678 17.7 69 64 60 55 50 4523 25 18,177 17 3 71 66 61 56 51 4624 26 18,238 17 2 72 67 61 56 51 4625 27 18,294 17.1 72 67 62 56 51 4626 28 18,346 17.1 72 67 62 57 51 4623 24 18,934 16 6 74 69 64 58 53 4824 25 18,967 16 5 75 69 64 59 53 4825 26 18,998 16 5 75 69 64 59 53 4826 27 19,026 16 5 75 69 64 59 53 4827 28 19,052 16 5 75 69 64 59 53 4823 23 19,758 15 9 72 67 61 55 5028 27 20,489 15 3 75 69 63 57 52 4627 26 20,518 15 3 75 69 63 58 52 4626 25 20,548 15 3 75 69 63 58 52 4625 24 20,581 15 2 75 69 64 58 52 4624 23 20,617 15 2 75 69 64 58 52 4628 26 21,277 14.7 72 66 60 54 4827 25 21,338 14.7 72 66 60 54 4826 24 21,404 14.7 72 66 60 54 4825 23 21,476 14 6 72 66 60 54 4819 17 22,082 14 2 74 68 62 56 5028 25 22,129 14 2 75 68 62 56 5027 24 22,227 14.1 75 69 62 56 5026 23 22,335 14 0 75 69 63 56 5028 24 23,051 13 6 71 65 58 52 4527 23 23,194 13 5 72 65 59 52 4623 19 23,917 13.1 74 67 60 54 4728 23 24,053 13 0 74 67 61 54 4724 19 24,957 12 6 70 63 56 4925 19 25,997 12.1 73 66 58 5123 17 26,731 11.7 75 68 60 5326 19 27,037 11 6 68 61 5324 17 27,893 11 2 70 63 5527 19 28,077 11 2 Not Recommended 71 63 5525 17 29,055 10 8 73 65 5728 19 29,117 10 8 74 65 5726 17 30,218 10.4 68 5927 17 31,380 10 0 70 6228 17 32,542 9.6 73 64

12/02/2009 401-312B








17 28 23,991 13.1 4717 27 24,880 12.6 49 4517 26 25,837 12.1 51 4719 28 26,814 11.7 53 49 4517 25 26,870 11.7 53 49 45 Not Recommended19 27 27,807 11.3 55 51 4717 24 27,990 11.2 55 51 4719 26 28,877 10.9 57 53 49 4517 23 29,207 10.7 57 53 49 4519 25 30,032 10.4 59 55 51 4619 24 31,283 10.0 61 57 53 4823 28 32,459 9.7 64 59 55 50 4619 23 32,643 9.6 64 60 55 50 4623 27 33,661 9.3 66 61 57 52 4724 28 33,870 9.3 67 62 57 52 4823 26 34,956 9.0 69 64 59 54 4924 27 35,125 8.9 69 64 59 54 4925 28 35,282 8.9 69 64 59 54 49 4517 19 35,356 8.9 69 64 60 55 50 4523 25 36,354 8.6 71 66 61 56 51 4624 26 36,476 8.6 72 67 61 56 51 4625 27 36,588 8.6 72 67 62 56 51 4626 28 36,693 8.5 72 67 62 57 51 4623 24 37,869 8.3 74 69 64 58 53 4824 25 37,935 8.3 75 69 64 59 53 4825 26 37,995 8.3 75 69 64 59 53 4826 27 38,052 8.2 75 69 64 59 53 4827 28 38,104 8.2 75 69 64 59 53 4823 23 39,515 7.9 72 67 61 55 5028 27 40,979 7.7 75 69 63 57 52 4627 26 41,035 7.6 75 69 63 58 52 4626 25 41,096 7.6 75 69 63 58 52 4625 24 41,162 7.6 75 69 64 58 52 4624 23 41,233 7.6 75 69 64 58 52 4628 26 42,555 7.4 72 66 60 54 4827 25 42,677 7.3 72 66 60 54 4826 24 42,808 7.3 72 66 60 54 4825 23 42,951 7.3 72 66 60 54 4819 17 44,164 7.1 74 68 62 56 5028 25 44,257 7.1 75 68 62 56 5027 24 44,455 7.1 75 69 62 56 5026 23 44,669 7.0 75 69 63 56 5028 24 46,101 6.8 71 65 58 52 4527 23 46,388 6.8 72 65 59 52 4623 19 47,834 6.6 74 67 60 54 4728 23 48,106 6.5 74 67 61 54 4724 19 49,914 6.3 70 63 56 4925 19 51,994 6.0 73 66 58 5123 17 53,462 5.9 75 68 60 5326 19 54,074 5.8 68 61 5324 17 55,786 5.6 70 63 5527 19 56,153 5.6 Not Recommended 71 63 5525 17 58,111 5.4 73 65 5728 19 58,233 5.4 74 65 5726 17 60,435 5.2 68 5927 17 62,760 5.0 70 6228 17 65,084 4.8 73 64

401-312B 12/02/2009








17 28 10,130 20 6 60 55 51 4717 27 10,505 19 9 62 57 53 4917 26 10,909 19 2 64 60 55 51 46 Not Recommended19 28 11,321 18 5 67 62 57 52 4817 25 11,345 18.4 67 62 57 53 4819 27 11,741 17 8 69 64 59 54 4917 24 11,818 17.7 70 65 60 55 50 4519 26 12,192 17.1 72 67 62 56 51 4617 23 12,332 17 0 73 67 62 57 52 4719 25 12,680 16 5 75 69 64 59 53 4819 24 13,208 15 8 72 67 61 56 5023 28 13,705 15 3 75 69 63 58 52 4619 23 13,783 15 2 75 70 64 58 52 4623 27 14,212 14.7 72 66 60 54 4824 28 14,301 14 6 72 66 60 54 4823 26 14,759 14 2 75 68 62 56 5024 27 14,830 14.1 75 69 62 56 5025 28 14,897 14 0 75 69 63 56 5017 19 14,928 14 0 75 69 63 57 5023 25 15,349 13 6 71 65 58 52 4524 26 15,401 13 6 71 65 58 52 4525 27 15,448 13 5 72 65 59 52 4626 28 15,493 13 5 72 65 59 52 4623 24 15,989 13.1 74 67 61 54 4724 25 16,017 13.1 74 67 61 54 4725 26 16,043 13 0 74 68 61 54 4726 27 16,066 13 0 74 68 61 54 4727 28 16,088 13 0 74 68 61 54 4723 23 16,684 12 5 70 63 56 4928 27 17,302 12.1 73 66 58 5127 26 17,326 12.1 73 66 58 5126 25 17,352 12.1 73 66 58 5125 24 17,379 12 0 73 66 59 5124 23 17,410 12 0 73 66 59 5128 26 17,968 11 6 68 60 5327 25 18,019 11 6 68 61 5326 24 18,075 11 6 68 61 5325 23 18,135 11 5 69 61 5319 17 18,647 11 2 71 63 5528 25 18,686 11 2 71 63 5527 24 18,770 11.1 Not Recommended 71 63 5526 23 18,860 11.1 71 64 5628 24 19,465 10.7 74 66 5727 23 19,586 10.7 74 66 5823 19 20,197 10.4 68 6028 23 20,311 10 3 68 6024 19 21,075 9.9 71 6225 19 21,953 9.5 74 6523 17 22,573 9.3 6726 19 22,831 9.2 6724 17 23,554 8.9 6927 19 23,709 8.8 7025 17 24,536 8.5 7228 19 24,587 8.5 7226 17 25,517 8.2 7527 17 26,498 7.928 17 27,480 7.6

12/02/2009 401-312B








17 28 20,259 10.3 60 55 51 4717 27 21,010 10.0 62 57 53 4917 26 21,818 9.6 64 60 55 51 46 Not Recommended19 28 22,643 9.2 67 62 57 52 4817 25 22,691 9.2 67 62 57 53 4819 27 23,482 8.9 69 64 59 54 4917 24 23,636 8.8 70 65 60 55 50 4519 26 24,385 8.6 72 67 62 56 51 4617 23 24,664 8.5 73 67 62 57 52 4719 25 25,360 8.2 75 69 64 59 53 4819 24 26,417 7.9 72 67 61 56 5023 28 27,410 7.6 75 69 63 58 52 4619 23 27,565 7.6 75 70 64 58 52 4623 27 28,425 7.4 72 66 60 54 4824 28 28,602 7.3 72 66 60 54 4823 26 29,518 7.1 75 68 62 56 5024 27 29,661 7.0 75 69 62 56 5025 28 29,793 7.0 75 69 63 56 5017 19 29,856 7.0 75 69 63 57 5023 25 30,699 6.8 71 65 58 52 4524 26 30,802 6.8 71 65 58 52 4525 27 30,897 6.8 72 65 59 52 4626 28 30,985 6.7 72 65 59 52 4623 24 31,978 6.5 74 67 61 54 4724 25 32,034 6.5 74 67 61 54 4725 26 32,085 6.5 74 68 61 54 4726 27 32,133 6.5 74 68 61 54 4727 28 32,177 6.5 74 68 61 54 4723 23 33,368 6.3 70 63 56 4928 27 34,604 6.0 73 66 58 5127 26 34,652 6.0 73 66 58 5126 25 34,703 6.0 73 66 58 5125 24 34,759 6.0 73 66 59 5124 23 34,819 6.0 73 66 59 5128 26 35,935 5.8 68 60 5327 25 36,038 5.8 68 61 5326 24 36,149 5.8 68 61 5325 23 36,270 5.8 69 61 5319 17 37,294 5.6 71 63 5528 25 37,373 5.6 71 63 5527 24 37,540 5.6 Not Recommended 71 63 5526 23 37,721 5.5 71 64 5628 24 38,930 5.4 74 66 5727 23 39,172 5.3 74 66 5823 19 40,393 5.2 68 6028 23 40,622 5.1 68 6024 19 42,150 5.0 71 6225 19 43,906 4.8 74 6523 17 45,146 4.6 6726 19 45,662 4.6 6724 17 47,108 4.4 6927 19 47,418 4.4 7025 17 49,071 4.3 7228 19 49,175 4.3 7226 17 51,034 4.1 7527 17 52,997 3.928 17 54,960 3.8

401-312B 12/02/2009


30in Twin Row, 6-Finger

3PT YIELD PRO 1225 - 1625 TWIN ROW 30"ATTENTION ! ! ! (For all seed corn types) 6 Finger MeterGreat Plains always recommends test stand calibration of the finger meter to the population and ground speed desired





17 28 20,259 20 6 60 55 51 4717 27 21,010 19 9 62 57 53 4917 26 21,818 19 2 64 60 55 51 4619 28 22,643 18 5 67 62 57 52 48 Not Recommended17 25 22,691 18.4 67 62 57 53 4819 27 23,482 17 8 69 64 59 54 4917 24 23,636 17.7 70 65 60 55 50 4519 26 24,385 17.1 72 67 62 56 51 4617 23 24,664 17 0 73 67 62 57 52 4719 25 25,360 16 5 75 69 64 59 53 4819 24 26,417 15 8 78 72 67 61 56 5023 28 27,410 15 3 81 75 69 63 58 52 4619 23 27,565 15 2 81 75 70 64 58 52 4623 27 28,425 14.7 84 78 72 66 60 54 4824 28 28,602 14 6 84 78 72 66 60 54 4823 26 29,518 14 2 81 75 68 62 56 5024 27 29,661 14.1 81 75 69 62 56 5025 28 29,793 14 0 82 75 69 63 56 5017 19 29,856 14 0 82 75 69 63 57 5023 25 30,699 13 6 84 78 71 65 58 52 4524 26 30,802 13 6 84 78 71 65 58 52 4525 27 30,897 13 5 85 78 72 65 59 52 4626 28 30,985 13 5 85 78 72 65 59 52 4623 24 31,978 13.1 81 74 67 61 54 4724 25 32,034 13.1 81 74 67 61 54 4725 26 32,085 13 0 81 74 68 61 54 4726 27 32,133 13 0 81 74 68 61 54 4727 28 32,177 13 0 81 74 68 61 54 4723 23 33,368 12 5 84 77 70 63 56 4928 27 34,604 12.1 80 73 66 58 5127 26 34,652 12.1 80 73 66 58 5126 25 34,703 12.1 80 73 66 58 5125 24 34,759 12 0 80 73 66 59 5124 23 34,819 12 0 81 73 66 59 5128 26 35,935 11 6 83 76 68 60 5327 25 36,038 11 6 83 76 68 61 5326 24 36,149 11 6 84 76 68 61 5325 23 36,270 11 5 84 76 69 61 5319 17 37,294 11 2 78 71 63 5528 25 37,373 11 2 79 71 63 5527 24 37,540 11.1 79 71 63 5526 23 37,721 11.1 79 71 64 5628 24 38,930 10.7 82 74 66 5727 23 39,172 10.7 82 74 66 5823 19 40,393 10.4 85 77 68 6028 23 40,622 10 3 85 77 68 6024 19 42,150 9.9 80 71 6225 19 43,906 9.5 Not Recommended 83 74 6523 17 45,146 9.3 76 6726 19 45,662 9.2 77 6724 17 47,108 8.9 79 6927 19 47,418 8.8 80 7025 17 49,071 8.5 83 7228 19 49,175 8.5 83 7226 17 51,034 8.2 7527 17 52,997 7.9 7828 17 54,960 7.6 81

12/02/2009 401-312B


30in Twin Row, 12-Finger (page 1 of 2)

3PT YIELD PRO 1225 - 1625 TWIN ROW 30" Page 1 of 2

ATTENTION ! ! ! (For all seed corn types) 12 Finger MeterGreat Plains always recommends test stand calibration of the finger meter to the population and ground speed desired





17 28 31,989 13.1 4717 27 33,173 12.6 49 4517 26 34,449 12.1 51 4719 28 35,752 11.7 53 49 45 Not Recommended17 25 35,827 11.7 53 49 4519 27 37,076 11.3 55 51 4717 24 37,320 11.2 55 51 4719 26 38,502 10.9 57 53 49 4517 23 38,943 10.7 57 53 49 4519 25 40,042 10.4 59 55 51 4619 24 41,711 10.0 61 57 53 4823 28 43,279 9.7 64 59 55 50 4619 23 43,524 9.6 64 60 55 50 4623 27 44,882 9.3 66 61 57 52 4724 28 45,160 9.3 67 62 57 52 4823 26 46,608 9.0 69 64 59 54 4924 27 46,833 8.9 69 64 59 54 4925 28 47,042 8.9 69 64 59 54 49 4517 19 47,141 8.9 69 64 60 55 50 4523 25 48,472 8.6 71 66 61 56 51 4624 26 48,634 8.6 72 67 61 56 51 4625 27 48,784 8.6 72 67 62 56 51 4626 28 48,924 8.5 72 67 62 57 51 4623 24 50,492 8.3 74 69 64 58 53 4824 25 50,580 8.3 75 69 64 59 53 4825 26 50,661 8.3 75 69 64 59 53 4826 27 50,736 8.2 75 69 64 59 53 4827 28 50,805 8.2 75 69 64 59 53 4823 23 52,687 7.9 72 67 61 55 5028 27 54,638 7.7 75 69 63 57 52 4627 26 54,713 7.6 75 69 63 58 52 4626 25 54,795 7.6 75 69 63 58 52 4625 24 54,882 7.6 75 69 64 58 52 4624 23 54,978 7.6 75 69 64 58 52 4628 26 56,740 7.4 72 66 60 54 4827 25 56,902 7.3 72 66 60 54 4826 24 57,078 7.3 72 66 60 54 4825 23 57,269 7.3 72 66 60 54 4819 17 58,886 7.1 74 68 62 56 5028 25 59,009 7.1 75 68 62 56 5027 24 59,273 7.1 75 69 62 56 5026 23 59,559 7.0 75 69 63 56 5028 24 61,468 6.8 71 65 58 52 4527 23 61,850 6.8 72 65 59 52 4623 19 63,779 6.6 74 67 60 54 4728 23 64,141 6.5 74 67 61 54 4724 19 66,552 6.3 70 63 56 4925 19 69,325 6.0 73 66 58 5123 17 71,282 5.9 75 68 60 5326 19 72,098 5.8 68 61 5324 17 74,382 5.6 70 63 5527 19 74,871 5.6 Not Recommended 71 63 5525 17 77,481 5.4 73 65 5728 19 77,644 5.4 74 65 5726 17 80,580 5.2 68 5927 17 83,679 5.0 70 6228 17 86,779 4.8 73 64

401-312B 12/02/2009









17 28 40,519 10 3 60 55 51 4717 27 42,020 10 0 62 57 53 4917 26 43,636 9.6 64 60 55 51 4619 28 45,286 9.2 67 62 57 52 48 Not Recommended17 25 45,381 9.2 67 62 57 53 4819 27 46,963 8.9 69 64 59 54 4917 24 47,272 8.8 70 65 60 55 50 4519 26 48,769 8.6 72 67 62 56 51 4617 23 49,327 8.5 73 67 62 57 52 4719 25 50,720 8.2 75 69 64 59 53 4819 24 52,833 7.9 72 67 61 56 5023 28 54,820 7.6 75 69 63 58 52 4619 23 55,131 7.6 75 70 64 58 52 4623 27 56,850 7.4 72 66 60 54 4824 28 57,203 7.3 72 66 60 54 4823 26 59,037 7.1 75 68 62 56 5024 27 59,322 7.0 75 69 62 56 5025 28 59,587 7.0 75 69 63 56 5017 19 59,712 7.0 75 69 63 57 5023 25 61,398 6.8 71 65 58 52 4524 26 61,603 6.8 71 65 58 52 4525 27 61,793 6.8 72 65 59 52 4626 28 61,970 6.7 72 65 59 52 4623 24 63,956 6.5 74 67 61 54 4724 25 64,067 6.5 74 67 61 54 4725 26 64,170 6.5 74 68 61 54 4726 27 64,265 6.5 74 68 61 54 4727 28 64,353 6.5 74 68 61 54 4723 23 66,737 6.3 70 63 56 4928 27 69,209 6.0 73 66 58 5127 26 69,304 6.0 73 66 58 5126 25 69,406 6.0 73 66 58 5125 24 69,518 6.0 73 66 59 5124 23 69,639 6.0 73 66 59 5128 26 71,871 5.8 68 60 5327 25 72,076 5.8 68 61 5326 24 72,298 5.8 68 61 5325 23 72,540 5.8 69 61 5319 17 74,588 5.6 71 63 5528 25 74,745 5.6 71 63 5527 24 75,079 5.6 71 63 5526 23 75,442 5.5 71 64 5628 24 77,860 5.4 74 66 5727 23 78,343 5.3 74 66 5823 19 80,787 5.2 68 6028 23 81,245 5.1 68 6024 19 84,299 5.0 71 6225 19 87,812 4.8 Not Recommended 74 6523 17 90,291 4.6 6726 19 91,324 4.6 6724 17 94,217 4.4 6927 19 94,837 4.4 7025 17 98,143 4.3 7228 19 98,349 4.3 7226 17 102,068 4.1 7527 17 105,994 3.928 17 109,920 3.8

12/02/2009 401-312B








17 28 8,441 20.6 60 55 51 4717 27 8,754 19.9 62 57 53 4917 26 9,091 19.2 64 60 55 51 46 Not Recommended19 28 9,435 18.5 67 62 57 52 4817 25 9,454 18.4 67 62 57 53 4819 27 9,784 17.8 69 64 59 54 4917 24 9,848 17.7 70 65 60 55 50 4519 26 10,160 17.1 72 67 62 56 51 4617 23 10,277 17.0 73 67 62 57 52 4719 25 10,567 16.5 75 69 64 59 53 4819 24 11,007 15.8 72 67 61 56 5023 28 11,421 15.3 75 69 63 58 52 4619 23 11,486 15.2 75 70 64 58 52 4623 27 11,844 14.7 72 66 60 54 4824 28 11,917 14.6 72 66 60 54 4823 26 12,299 14.2 75 68 62 56 5024 27 12,359 14.1 75 69 62 56 5025 28 12,414 14.0 75 69 63 56 5017 19 12,440 14.0 75 69 63 57 5023 25 12,791 13.6 71 65 58 52 4524 26 12,834 13.6 71 65 58 52 4525 27 12,874 13.5 72 65 59 52 4626 28 12,910 13.5 72 65 59 52 4623 24 13,324 13.1 74 67 61 54 4724 25 13,347 13.1 74 67 61 54 4725 26 13,369 13.0 74 68 61 54 4726 27 13,389 13.0 74 68 61 54 4727 28 13,407 13.0 74 68 61 54 4723 23 13,904 12.5 70 63 56 4928 27 14,418 12.1 73 66 58 5127 26 14,438 12.1 73 66 58 5126 25 14,460 12.1 73 66 58 5125 24 14,483 12.0 73 66 59 5124 23 14,508 12.0 73 66 59 5128 26 14,973 11.6 68 60 5327 25 15,016 11.6 68 61 5326 24 15,062 11.6 68 61 5325 23 15,113 11.5 69 61 5319 17 15,539 11.2 71 63 5528 25 15,572 11.2 71 63 5527 24 15,641 11.1 71 63 5526 23 15,717 11.1 71 64 5628 24 16,221 10.7 74 66 5727 23 16,322 10.7 Not Recommended 74 66 5823 19 16,831 10.4 68 6028 23 16,926 10.3 68 6024 19 17,562 9.9 71 6225 19 18,294 9.5 74 6523 17 18,811 9.3 6726 19 19,026 9.2 6724 17 19,629 8.9 6927 19 19,758 8.8 7025 17 20,446 8.5 7228 19 20,489 8.5 7226 17 21,264 8.2 7527 17 22,082 7.928 17 22,900 7.6

401-312B 12/02/2009








17 28 16,883 10 3 60 55 51 4717 27 17,508 10 0 62 57 53 4917 26 18,182 9.6 64 60 55 51 46 Not Recommended19 28 18,869 9.2 67 62 57 52 4817 25 18,909 9.2 67 62 57 53 4819 27 19,568 8.9 69 64 59 54 4917 24 19,697 8.8 70 65 60 55 50 4519 26 20,321 8.6 72 67 62 56 51 4617 23 20,553 8.5 73 67 62 57 52 4719 25 21,133 8.2 75 69 64 59 53 4819 24 22,014 7.9 72 67 61 56 5023 28 22,842 7.6 75 69 63 58 52 4619 23 22,971 7.6 75 70 64 58 52 4623 27 23,687 7.4 72 66 60 54 4824 28 23,835 7.3 72 66 60 54 4823 26 24,599 7.1 75 68 62 56 5024 27 24,717 7.0 75 69 62 56 5025 28 24,828 7.0 75 69 63 56 5017 19 24,880 7.0 75 69 63 57 5023 25 25,582 6.8 71 65 58 52 4524 26 25,668 6.8 71 65 58 52 4525 27 25,747 6.8 72 65 59 52 4626 28 25,821 6.7 72 65 59 52 4623 24 26,648 6.5 74 67 61 54 4724 25 26,695 6.5 74 67 61 54 4725 26 26,738 6.5 74 68 61 54 4726 27 26,777 6.5 74 68 61 54 4727 28 26,814 6.5 74 68 61 54 4723 23 27,807 6.3 70 63 56 4928 27 28,837 6.0 73 66 58 5127 26 28,877 6.0 73 66 58 5126 25 28,919 6.0 73 66 58 5125 24 28,966 6.0 73 66 59 5124 23 29,016 6.0 73 66 59 5128 26 29,946 5.8 68 60 5327 25 30,032 5.8 68 61 5326 24 30,124 5.8 68 61 5325 23 30,225 5.8 69 61 5319 17 31,078 5.6 71 63 5528 25 31,144 5.6 71 63 5527 24 31,283 5.6 71 63 5526 23 31,434 5.5 71 64 5628 24 32,442 5.4 74 66 5727 23 32,643 5.3 Not Recommended 74 66 5823 19 33,661 5.2 68 6028 23 33,852 5.1 68 6024 19 35,125 5.0 71 6225 19 36,588 4.8 74 6523 17 37,621 4.6 6726 19 38,052 4.6 6724 17 39,257 4.4 6927 19 39,515 4.4 7025 17 40,893 4.3 7228 19 40,979 4.3 7226 17 42,528 4.1 7527 17 44,164 3.928 17 45,800 3.8

12/02/2009 401-312B








17 28 16,883 20.6 60 55 51 4717 27 17,508 19.9 62 57 53 4917 26 18,182 19.2 64 60 55 51 46 Not Recommended19 28 18,869 18.5 67 62 57 52 4817 25 18,909 18.4 67 62 57 53 4819 27 19,568 17.8 69 64 59 54 4917 24 19,697 17.7 70 65 60 55 50 4519 26 20,321 17.1 72 67 62 56 51 4617 23 20,553 17.0 73 67 62 57 52 4719 25 21,133 16.5 75 69 64 59 53 4819 24 22,014 15.8 78 72 67 61 56 5023 28 22,842 15.3 81 75 69 63 58 52 4619 23 22,971 15.2 81 75 70 64 58 52 4623 27 23,687 14.7 84 78 72 66 60 54 4824 28 23,835 14.6 84 78 72 66 60 54 4823 26 24,599 14.2 81 75 68 62 56 5024 27 24,717 14.1 81 75 69 62 56 5025 28 24,828 14.0 82 75 69 63 56 5017 19 24,880 14.0 82 75 69 63 57 5023 25 25,582 13.6 84 78 71 65 58 52 4524 26 25,668 13.6 84 78 71 65 58 52 4525 27 25,747 13.5 85 78 72 65 59 52 4626 28 25,821 13.5 85 78 72 65 59 52 4623 24 26,648 13.1 81 74 67 61 54 4724 25 26,695 13.1 81 74 67 61 54 4725 26 26,738 13.0 81 74 68 61 54 4726 27 26,777 13.0 81 74 68 61 54 4727 28 26,814 13.0 81 74 68 61 54 4723 23 27,807 12.5 84 77 70 63 56 4928 27 28,837 12.1 80 73 66 58 5127 26 28,877 12.1 80 73 66 58 5126 25 28,919 12.1 80 73 66 58 5125 24 28,966 12.0 80 73 66 59 5124 23 29,016 12.0 81 73 66 59 5128 26 29,946 11.6 83 76 68 60 5327 25 30,032 11.6 83 76 68 61 5326 24 30,124 11.6 84 76 68 61 5325 23 30,225 11.5 84 76 69 61 5319 17 31,078 11.2 78 71 63 5528 25 31,144 11.2 79 71 63 5527 24 31,283 11.1 79 71 63 5526 23 31,434 11.1 79 71 64 5628 24 32,442 10.7 82 74 66 5727 23 32,643 10.7 82 74 66 5823 19 33,661 10.4 85 77 68 6028 23 33,852 10.3 85 77 68 6024 19 35,125 9.9 80 71 6225 19 36,588 9.5 Not Recommended 83 74 6523 17 37,621 9.3 76 6726 19 38,052 9.2 77 6724 17 39,257 8.9 79 6927 19 39,515 8.8 80 7025 17 40,893 8.5 83 7228 19 40,979 8.5 83 7226 17 42,528 8.2 7527 17 44,164 7.9 7828 17 45,800 7.6 81

401-312B 12/02/2009









17 28 19,993 17.417 27 20,733 16 817 26 21,531 16 219 28 22,345 15 617 25 22,392 15 619 27 23,173 15 017 24 23,325 14 919 26 24,064 14 517 23 24,339 14 319 25 25,026 13 919 24 26,069 13.4 4623 28 27,049 12 9 4819 23 27,203 12 8 48 4523 27 28,051 12.4 50 4624 28 28,225 12 3 50 4623 26 29,130 12 0 51 4824 27 29,271 11 9 52 4825 28 29,401 11 9 52 48 45 Not Recommended17 19 29,463 11 8 52 48 4523 25 30,295 11 5 54 50 4624 26 30,396 11 5 54 50 4625 27 30,490 11.4 54 50 4626 28 30,577 11.4 54 50 4623 24 31,557 11 0 56 52 4824 25 31,612 11 0 56 52 4825 26 31,663 11 0 56 52 4826 27 31,710 11 0 56 52 4827 28 31,753 11 0 56 52 4823 23 32,929 10 6 58 54 50 4628 27 34,149 10 2 60 56 52 4727 26 34,196 10 2 60 56 52 4726 25 34,247 10 2 61 56 52 4825 24 34,301 10 2 61 56 52 4824 23 34,361 10.1 61 56 52 4828 26 35,462 9.8 63 58 54 49 4527 25 35,564 9.8 63 58 54 49 4526 24 35,674 9.8 63 59 54 50 4525 23 35,793 9.7 63 59 54 50 4519 17 36,803 9.5 65 60 56 51 4628 25 36,881 9.4 65 61 56 51 4727 24 37,046 9.4 65 61 56 51 4726 23 37,225 9.4 66 61 56 52 4728 24 38,418 9.1 68 63 58 53 4927 23 38,656 9.0 68 63 59 54 4923 19 39,862 8.7 70 65 60 55 50 4528 23 40,088 8.7 71 66 61 56 51 4624 19 41,595 8.4 74 68 63 58 53 4725 19 43,328 8.0 71 66 60 55 4923 17 44,552 7.8 73 68 62 56 51 4526 19 45,061 7.7 74 68 63 57 51 4624 17 46,489 7.5 70 65 59 53 4727 19 46,794 7.4 71 65 59 53 4725 17 48,426 7.2 73 67 61 55 4928 19 48,528 7.2 74 67 61 55 4926 17 50,363 6.9 70 64 57 51 4527 17 52,300 6.7 Not Recommended 73 66 59 53 4628 17 54,237 6.4 75 68 62 55 48

12/02/2009 401-312B









17 28 25,324 13.8 4517 27 26,262 13.3 4617 26 27,272 12.8 48 4519 28 28,304 12.3 50 4617 25 28,363 12.3 50 4719 27 29,352 11.9 52 4817 24 29,545 11.8 52 48 4519 26 30,481 11.4 54 50 46 Not Recommended17 23 30,830 11.3 54 51 4719 25 31,700 11.0 56 52 4819 24 33,021 10.6 58 54 50 4623 28 34,262 10.2 61 56 52 4819 23 34,457 10.1 61 57 52 4823 27 35,531 9.8 63 58 54 49 4524 28 35,752 9.7 63 59 54 50 4523 26 36,898 9.4 65 61 56 51 4724 27 37,076 9.4 66 61 56 51 4725 28 37,242 9.4 66 61 56 52 4717 19 37,320 9.3 66 61 57 52 4723 25 38,374 9.1 68 63 58 53 4824 26 38,502 9.1 68 63 58 53 4925 27 38,621 9.0 68 63 59 54 4926 28 38,731 9.0 68 64 59 54 4923 24 39,973 8.7 71 66 61 56 50 4524 25 40,042 8.7 71 66 61 56 51 4625 26 40,106 8.7 71 66 61 56 51 4626 27 40,166 8.7 71 66 61 56 51 4627 28 40,221 8.7 71 66 61 56 51 4623 23 41,711 8.4 74 68 63 58 53 4728 27 43,255 8.1 71 66 60 55 4927 26 43,315 8.0 71 66 60 55 4926 25 43,379 8.0 71 66 60 55 4925 24 43,449 8.0 71 66 60 55 4924 23 43,524 8.0 71 66 60 55 4928 26 44,919 7.8 74 68 62 57 51 4527 25 45,047 7.7 74 68 63 57 51 4626 24 45,186 7.7 74 68 63 57 51 4625 23 45,338 7.7 74 69 63 57 52 4619 17 46,618 7.5 71 65 59 53 4728 25 46,716 7.5 71 65 59 53 4727 24 46,924 7.4 71 65 59 53 4726 23 47,151 7.4 71 65 60 54 4828 24 48,662 7.2 74 68 61 55 4927 23 48,965 7.1 74 68 62 56 4923 19 50,492 6.9 70 64 57 51 4528 23 50,778 6.9 71 64 58 51 4524 19 52,687 6.6 73 67 60 53 4725 19 54,882 6.3 69 62 55 4923 17 56,432 6.2 71 64 57 5026 19 57,078 6.1 72 65 58 5024 17 58,886 5.9 74 67 59 5227 19 59,273 5.9 75 67 60 5225 17 61,339 5.7 70 62 5428 19 61,468 5.7 Not Recommended 70 62 5426 17 63,793 5.5 72 64 5627 17 66,246 5.3 75 67 5928 17 68,700 5.1 69 61

401-312B 12/02/2009








17 28 7,997 20 6 60 55 51 4717 27 8,293 19 9 62 57 53 4917 26 8,612 19 2 64 60 55 51 46 Not Recommended19 28 8,938 18 5 67 62 57 52 4817 25 8,957 18.4 67 62 57 53 4819 27 9,269 17 8 69 64 59 54 4917 24 9,330 17.7 70 65 60 55 50 4519 26 9,626 17.1 72 67 62 56 51 4617 23 9,736 17 0 73 67 62 57 52 4719 25 10,011 16 5 75 69 64 59 53 4819 24 10,428 15 8 72 67 61 56 5023 28 10,820 15 3 75 69 63 58 52 4619 23 10,881 15 2 75 70 64 58 52 4623 27 11,220 14.7 72 66 60 54 4824 28 11,290 14 6 72 66 60 54 4823 26 11,652 14 2 75 68 62 56 5024 27 11,708 14.1 75 69 62 56 5025 28 11,761 14 0 75 69 63 56 5017 19 11,785 14 0 75 69 63 57 5023 25 12,118 13 6 71 65 58 52 4524 26 12,159 13 6 71 65 58 52 4525 27 12,196 13 5 72 65 59 52 4626 28 12,231 13 5 72 65 59 52 4623 24 12,623 13.1 74 67 61 54 4724 25 12,645 13.1 74 67 61 54 4725 26 12,665 13 0 74 68 61 54 4726 27 12,684 13 0 74 68 61 54 4727 28 12,701 13 0 74 68 61 54 4723 23 13,172 12 5 70 63 56 4928 27 13,660 12.1 73 66 58 5127 26 13,678 12.1 73 66 58 5126 25 13,699 12.1 73 66 58 5125 24 13,721 12 0 73 66 59 5124 23 13,744 12 0 73 66 59 5128 26 14,185 11 6 68 60 5327 25 14,226 11 6 68 61 5326 24 14,269 11 6 68 61 5325 23 14,317 11 5 69 61 5319 17 14,721 11 2 71 63 5528 25 14,752 11 2 71 63 5527 24 14,818 11.1 71 63 5526 23 14,890 11.1 71 64 5628 24 15,367 10.7 74 66 5727 23 15,463 10.7 Not Recommended 74 66 5823 19 15,945 10.4 68 6028 23 16,035 10 3 68 6024 19 16,638 9.9 71 6225 19 17,331 9.5 74 6523 17 17,821 9.3 6726 19 18,025 9.2 6724 17 18,595 8.9 6927 19 18,718 8.8 7025 17 19,370 8.5 7228 19 19,411 8.5 7226 17 20,145 8.2 7527 17 20,920 7.928 17 21,695 7.6

12/02/2009 401-312B









401-312B 12/02/2009








17 28 15,994 20 6 60 55 51 4717 27 16,587 19 9 62 57 53 4917 26 17,225 19 2 64 60 55 51 46 Not Recommended19 28 17,876 18 5 67 62 57 52 4817 25 17,914 18.4 67 62 57 53 4819 27 18,538 17 8 69 64 59 54 4917 24 18,660 17.7 70 65 60 55 50 4519 26 19,251 17.1 72 67 62 56 51 4617 23 19,471 17 0 73 67 62 57 52 4719 25 20,021 16 5 75 69 64 59 53 4819 24 20,855 15 8 78 72 67 61 56 5023 28 21,639 15 3 81 75 69 63 58 52 4619 23 21,762 15 2 81 75 70 64 58 52 4623 27 22,441 14.7 84 78 72 66 60 54 4824 28 22,580 14 6 84 78 72 66 60 54 4823 26 23,304 14 2 81 75 68 62 56 5024 27 23,416 14.1 81 75 69 62 56 5025 28 23,521 14 0 82 75 69 63 56 5017 19 23,571 14 0 82 75 69 63 57 5023 25 24,236 13 6 84 78 71 65 58 52 4524 26 24,317 13 6 84 78 71 65 58 52 4525 27 24,392 13 5 85 78 72 65 59 52 4626 28 24,462 13 5 85 78 72 65 59 52 4623 24 25,246 13.1 81 74 67 61 54 4724 25 25,290 13.1 81 74 67 61 54 4725 26 25,330 13 0 81 74 68 61 54 4726 27 25,368 13 0 81 74 68 61 54 4727 28 25,403 13 0 81 74 68 61 54 4723 23 26,344 12 5 84 77 70 63 56 4928 27 27,319 12.1 80 73 66 58 5127 26 27,357 12.1 80 73 66 58 5126 25 27,397 12.1 80 73 66 58 5125 24 27,441 12 0 80 73 66 59 5124 23 27,489 12 0 81 73 66 59 5128 26 28,370 11 6 83 76 68 60 5327 25 28,451 11 6 83 76 68 61 5326 24 28,539 11 6 84 76 68 61 5325 23 28,634 11 5 84 76 69 61 5319 17 29,443 11 2 78 71 63 5528 25 29,505 11 2 79 71 63 5527 24 29,636 11.1 79 71 63 5526 23 29,780 11.1 79 71 64 5628 24 30,734 10.7 82 74 66 5727 23 30,925 10.7 82 74 66 5823 19 31,890 10.4 85 77 68 6028 23 32,070 10 3 85 77 68 6024 19 33,276 9.9 80 71 6225 19 34,663 9.5 83 74 6523 17 35,641 9.3 Not Recommended 76 6726 19 36,049 9.2 77 6724 17 37,191 8.9 79 6927 19 37,436 8.8 80 7025 17 38,740 8.5 83 7228 19 38,822 8.5 83 7226 17 40,290 8.2 7527 17 41,840 7.9 7828 17 43,389 7.6 81

12/02/2009 401-312B









17 28 18,941 17.417 27 19,642 16.817 26 20,398 16.219 28 21,169 15.617 25 21,213 15.619 27 21,953 15.017 24 22,097 14.919 26 22,797 14.517 23 23,058 14.319 25 23,709 13.919 24 24,697 13.4 4623 28 25,626 12.9 4819 23 25,771 12.8 48 4523 27 26,575 12.4 50 4624 28 26,740 12.3 50 4623 26 27,597 12.0 51 4824 27 27,730 11.9 52 4825 28 27,854 11.9 52 48 4517 19 27,912 11.8 52 48 45 Not Recommended23 25 28,701 11.5 54 50 4624 26 28,797 11.5 54 50 4625 27 28,885 11.4 54 50 4626 28 28,968 11.4 54 50 4623 24 29,896 11.0 56 52 4824 25 29,948 11.0 56 52 4825 26 29,996 11.0 56 52 4826 27 30,041 11.0 56 52 4827 28 30,082 11.0 56 52 4823 23 31,196 10.6 58 54 50 4628 27 32,352 10.2 60 56 52 4727 26 32,396 10.2 60 56 52 4726 25 32,444 10.2 61 56 52 4825 24 32,496 10.2 61 56 52 4824 23 32,553 10.1 61 56 52 4828 26 33,596 9.8 63 58 54 49 4527 25 33,692 9.8 63 58 54 49 4526 24 33,796 9.8 63 59 54 50 4525 23 33,909 9.7 63 59 54 50 4519 17 34,866 9.5 65 60 56 51 4628 25 34,940 9.4 65 61 56 51 4727 24 35,096 9.4 65 61 56 51 4726 23 35,265 9.4 66 61 56 52 4728 24 36,396 9.1 68 63 58 53 4927 23 36,622 9.0 68 63 59 54 4923 19 37,764 8.7 70 65 60 55 50 4528 23 37,978 8.7 71 66 61 56 51 4624 19 39,406 8.4 74 68 63 58 53 4725 19 41,048 8.0 71 66 60 55 4923 17 42,207 7.8 73 68 62 56 51 4526 19 42,690 7.7 74 68 63 57 51 4624 17 44,042 7.5 76 70 65 59 53 4727 19 44,332 7.4 71 65 59 53 4725 17 45,877 7.2 73 67 61 55 4928 19 45,973 7.2 74 67 61 55 4926 17 47,712 6.9 70 64 57 51 4527 17 49,547 6.7 73 66 59 53 4628 17 51,382 6.4 Not Recommended 75 68 62 55 48

401-312B 12/02/2009









17 28 23,991 13 8 4517 27 24,880 13 3 4617 26 25,837 12 8 48 4519 28 26,814 12 3 50 4617 25 26,870 12 3 50 4719 27 27,807 11 9 52 4817 24 27,990 11 8 52 48 45 Not Recommended19 26 28,877 11.4 54 50 4617 23 29,207 11 3 54 51 4719 25 30,032 11 0 56 52 4819 24 31,283 10 6 58 54 50 4623 28 32,459 10 2 61 56 52 4819 23 32,643 10.1 61 57 52 4823 27 33,661 9.8 63 58 54 49 4524 28 33,870 9.7 63 59 54 50 4523 26 34,956 9.4 65 61 56 51 4724 27 35,125 9.4 66 61 56 51 4725 28 35,282 9.4 66 61 56 52 4717 19 35,356 9.3 66 61 57 52 4723 25 36,354 9.1 68 63 58 53 4824 26 36,476 9.1 68 63 58 53 4925 27 36,588 9.0 68 63 59 54 4926 28 36,693 9.0 68 64 59 54 4923 24 37,869 8.7 71 66 61 56 50 4524 25 37,935 8.7 71 66 61 56 51 4625 26 37,995 8.7 71 66 61 56 51 4626 27 38,052 8.7 71 66 61 56 51 4627 28 38,104 8.7 71 66 61 56 51 4623 23 39,515 8.4 74 68 63 58 53 4728 27 40,979 8.1 71 66 60 55 4927 26 41,035 8.0 71 66 60 55 4926 25 41,096 8.0 71 66 60 55 4925 24 41,162 8.0 71 66 60 55 4924 23 41,233 8.0 71 66 60 55 4928 26 42,555 7.8 74 68 62 57 51 4527 25 42,677 7.7 74 68 63 57 51 4626 24 42,808 7.7 74 68 63 57 51 4625 23 42,951 7.7 74 69 63 57 52 4619 17 44,164 7.5 71 65 59 53 4728 25 44,257 7.5 71 65 59 53 4727 24 44,455 7.4 71 65 59 53 4726 23 44,669 7.4 71 65 60 54 4828 24 46,101 7.2 74 68 61 55 4927 23 46,388 7.1 74 68 62 56 4923 19 47,834 6.9 70 64 57 51 4528 23 48,106 6.9 71 64 58 51 4524 19 49,914 6.6 73 67 60 53 4725 19 51,994 6.3 69 62 55 4923 17 53,462 6.2 71 64 57 5026 19 54,074 6.1 72 65 58 5024 17 55,786 5.9 74 67 59 5227 19 56,153 5.9 75 67 60 5225 17 58,111 5.7 70 62 5428 19 58,233 5.7 70 62 5426 17 60,435 5.5 Not Recommended 72 64 5627 17 62,760 5.3 75 67 5928 17 65,084 5.1 69 61

12/02/2009 401-312B









401-312B 12/02/2009








17 28 15,195 10 3 60 55 51 4717 27 15,757 10 0 62 57 53 4917 26 16,363 9.6 64 60 55 51 46 Not Recommended19 28 16,982 9.2 67 62 57 52 4817 25 17,018 9.2 67 62 57 53 4819 27 17,611 8.9 69 64 59 54 4917 24 17,727 8.8 70 65 60 55 50 4519 26 18,288 8.6 72 67 62 56 51 4617 23 18,498 8.5 73 67 62 57 52 4719 25 19,020 8.2 75 69 64 59 53 4819 24 19,813 7.9 72 67 61 56 5023 28 20,557 7.6 75 69 63 58 52 4619 23 20,674 7.6 75 70 64 58 52 4623 27 21,319 7.4 72 66 60 54 4824 28 21,451 7.3 72 66 60 54 4823 26 22,139 7.1 75 68 62 56 5024 27 22,246 7.0 75 69 62 56 5025 28 22,345 7.0 75 69 63 56 5017 19 22,392 7.0 75 69 63 57 5023 25 23,024 6.8 71 65 58 52 4524 26 23,101 6.8 71 65 58 52 4525 27 23,173 6.8 72 65 59 52 4626 28 23,239 6.7 72 65 59 52 4623 24 23,984 6.5 74 67 61 54 4724 25 24,025 6.5 74 67 61 54 4725 26 24,064 6.5 74 68 61 54 4726 27 24,099 6.5 74 68 61 54 4727 28 24,133 6.5 74 68 61 54 4723 23 25,026 6.3 70 63 56 4928 27 25,953 6.0 73 66 58 5127 26 25,989 6.0 73 66 58 5126 25 26,027 6.0 73 66 58 5125 24 26,069 6.0 73 66 59 5124 23 26,114 6.0 73 66 59 5128 26 26,951 5.8 68 60 5327 25 27,028 5.8 68 61 5326 24 27,112 5.8 68 61 5325 23 27,203 5.8 69 61 5319 17 27,971 5.6 71 63 5528 25 28,030 5.6 71 63 5527 24 28,155 5.6 71 63 5526 23 28,291 5.5 71 64 5628 24 29,197 5.4 74 66 5727 23 29,379 5.3 Not Recommended 74 66 5823 19 30,295 5.2 68 6028 23 30,467 5.1 68 6024 19 31,612 5.0 71 6225 19 32,929 4.8 74 6523 17 33,859 4.6 6726 19 34,247 4.6 6724 17 35,331 4.4 6927 19 35,564 4.4 7025 17 36,803 4.3 7228 19 36,881 4.3 7226 17 38,276 4.1 7527 17 39,748 3.928 17 41,220 3.8

12/02/2009 401-312B








17 28 15,195 20.6 60 55 51 4717 27 15,757 19.9 62 57 53 4917 26 16,363 19.2 64 60 55 51 4619 28 16,982 18.5 67 62 57 52 4817 25 17,018 18.4 67 62 57 53 48 Not Recommended19 27 17,611 17.8 69 64 59 54 4917 24 17,727 17.7 70 65 60 55 50 4519 26 18,288 17.1 72 67 62 56 51 4617 23 18,498 17.0 73 67 62 57 52 4719 25 19,020 16.5 75 69 64 59 53 4819 24 19,813 15.8 78 72 67 61 56 5023 28 20,557 15.3 81 75 69 63 58 52 4619 23 20,674 15.2 81 75 70 64 58 52 4623 27 21,319 14.7 84 78 72 66 60 54 4824 28 21,451 14.6 84 78 72 66 60 54 4823 26 22,139 14.2 81 75 68 62 56 5024 27 22,246 14.1 81 75 69 62 56 5025 28 22,345 14.0 82 75 69 63 56 5017 19 22,392 14.0 82 75 69 63 57 5023 25 23,024 13.6 84 78 71 65 58 52 4524 26 23,101 13.6 84 78 71 65 58 52 4525 27 23,173 13.5 85 78 72 65 59 52 4626 28 23,239 13.5 85 78 72 65 59 52 4623 24 23,984 13.1 81 74 67 61 54 4724 25 24,025 13.1 81 74 67 61 54 4725 26 24,064 13.0 81 74 68 61 54 4726 27 24,099 13.0 81 74 68 61 54 4727 28 24,133 13.0 81 74 68 61 54 4723 23 25,026 12.5 84 77 70 63 56 4928 27 25,953 12.1 80 73 66 58 5127 26 25,989 12.1 80 73 66 58 5126 25 26,027 12.1 80 73 66 58 5125 24 26,069 12.0 80 73 66 59 5124 23 26,114 12.0 81 73 66 59 5128 26 26,951 11.6 83 76 68 60 5327 25 27,028 11.6 83 76 68 61 5326 24 27,112 11.6 84 76 68 61 5325 23 27,203 11.5 84 76 69 61 5319 17 27,971 11.2 78 71 63 5528 25 28,030 11.2 79 71 63 5527 24 28,155 11.1 79 71 63 5526 23 28,291 11.1 79 71 64 5628 24 29,197 10.7 82 74 66 5727 23 29,379 10.7 82 74 66 5823 19 30,295 10.4 85 77 68 6028 23 30,467 10.3 85 77 68 6024 19 31,612 9.9 80 71 6225 19 32,929 9.5 83 74 6523 17 33,859 9.3 76 6726 19 34,247 9.2 Not Recommended 77 6724 17 35,331 8.9 79 6927 19 35,564 8.8 80 7025 17 36,803 8.5 83 7228 19 36,881 8.5 83 7226 17 38,276 8.2 7527 17 39,748 7.9 7828 17 41,220 7.6 81

401-312B 12/02/2009









17 28 23,991 13.1 4717 27 24,880 12 6 49 4517 26 25,837 12.1 51 4719 28 26,814 11.7 53 49 4517 25 26,870 11.7 53 49 45 Not Recommended19 27 27,807 11 3 55 51 4717 24 27,990 11 2 55 51 4719 26 28,877 10 9 57 53 49 4517 23 29,207 10.7 57 53 49 4519 25 30,032 10.4 59 55 51 4619 24 31,283 10 0 61 57 53 4823 28 32,459 9.7 64 59 55 50 4619 23 32,643 9.6 64 60 55 50 4623 27 33,661 9.3 66 61 57 52 4724 28 33,870 9.3 67 62 57 52 4823 26 34,956 9.0 69 64 59 54 4924 27 35,125 8.9 69 64 59 54 4925 28 35,282 8.9 69 64 59 54 49 4517 19 35,356 8.9 69 64 60 55 50 4523 25 36,354 8.6 71 66 61 56 51 4624 26 36,476 8.6 72 67 61 56 51 4625 27 36,588 8.6 72 67 62 56 51 4626 28 36,693 8.5 72 67 62 57 51 4623 24 37,869 8.3 74 69 64 58 53 4824 25 37,935 8.3 75 69 64 59 53 4825 26 37,995 8.3 75 69 64 59 53 4826 27 38,052 8.2 75 69 64 59 53 4827 28 38,104 8.2 75 69 64 59 53 4823 23 39,515 7.9 72 67 61 55 5028 27 40,979 7.7 75 69 63 57 52 4627 26 41,035 7.6 75 69 63 58 52 4626 25 41,096 7.6 75 69 63 58 52 4625 24 41,162 7.6 75 69 64 58 52 4624 23 41,233 7.6 75 69 64 58 52 4628 26 42,555 7.4 72 66 60 54 4827 25 42,677 7.3 72 66 60 54 4826 24 42,808 7.3 72 66 60 54 4825 23 42,951 7.3 72 66 60 54 4819 17 44,164 7.1 74 68 62 56 5028 25 44,257 7.1 75 68 62 56 5027 24 44,455 7.1 75 69 62 56 5026 23 44,669 7.0 75 69 63 56 5028 24 46,101 6.8 71 65 58 52 4527 23 46,388 6.8 72 65 59 52 4623 19 47,834 6.6 74 67 60 54 4728 23 48,106 6.5 74 67 61 54 4724 19 49,914 6.3 70 63 56 4925 19 51,994 6.0 73 66 58 5123 17 53,462 5.9 75 68 60 5326 19 54,074 5.8 68 61 5324 17 55,786 5.6 70 63 5527 19 56,153 5.6 71 63 5525 17 58,111 5.4 73 65 5728 19 58,233 5.4 Not Recommended 74 65 5726 17 60,435 5.2 68 5927 17 62,760 5.0 70 6228 17 65,084 4.8 73 64

12/02/2009 401-312B









17 28 30,389 10.3 60 55 51 4717 27 31,515 10.0 62 57 53 49 Not Recommended17 26 32,727 9.6 64 60 55 51 4619 28 33,964 9.2 67 62 57 52 4817 25 34,036 9.2 67 62 57 53 4819 27 35,222 8.9 69 64 59 54 4917 24 35,454 8.8 70 65 60 55 50 4519 26 36,577 8.6 72 67 62 56 51 4617 23 36,995 8.5 73 67 62 57 52 4719 25 38,040 8.2 75 69 64 59 53 4819 24 39,625 7.9 72 67 61 56 5023 28 41,115 7.6 75 69 63 58 52 4619 23 41,348 7.6 75 70 64 58 52 4623 27 42,637 7.4 72 66 60 54 4824 28 42,902 7.3 72 66 60 54 4823 26 44,277 7.1 75 68 62 56 5024 27 44,491 7.0 75 69 62 56 5025 28 44,690 7.0 75 69 63 56 5017 19 44,784 7.0 75 69 63 57 5023 25 46,048 6.8 71 65 58 52 4524 26 46,202 6.8 71 65 58 52 4525 27 46,345 6.8 72 65 59 52 4626 28 46,478 6.7 72 65 59 52 4623 24 47,967 6.5 74 67 61 54 4724 25 48,051 6.5 74 67 61 54 4725 26 48,128 6.5 74 68 61 54 4726 27 48,199 6.5 74 68 61 54 4727 28 48,265 6.5 74 68 61 54 4723 23 50,053 6.3 70 63 56 4928 27 51,906 6.0 73 66 58 5127 26 51,978 6.0 73 66 58 5126 25 52,055 6.0 73 66 58 5125 24 52,138 6.0 73 66 59 5124 23 52,229 6.0 73 66 59 5128 26 53,903 5.8 68 60 5327 25 54,057 5.8 68 61 5326 24 54,224 5.8 68 61 5325 23 54,405 5.8 69 61 5319 17 55,941 5.6 71 63 5528 25 56,059 5.6 71 63 5527 24 56,309 5.6 71 63 5526 23 56,581 5.5 71 64 5628 24 58,395 5.4 74 66 5727 23 58,758 5.3 74 66 5823 19 60,590 5.2 68 6028 23 60,934 5.1 68 6024 19 63,224 5.0 71 6225 19 65,859 4.8 74 6523 17 67,718 4.6 6726 19 68,493 4.6 6724 17 70,663 4.4 6927 19 71,128 4.4 7025 17 73,607 4.3 7228 19 73,762 4.3 Not Recommended 7226 17 76,551 4.1 7527 17 79,495 3.928 17 82,440 3.8

401-312B 12/02/2009


Sprocket Indexing (Stagger)

This chapter applies to both ground and hydraulic drive,but only with finger meters.

If you are planting:• finger-metered,• twin-row crops,• at seed interval spacings above 61⁄2 inches,you can synchronize each pair of adjacent meters in atwin row so that you achieve the maximum seed-to-seed spacing between the units of the pair.

If you are planting:- single-row,- or with singulating meters,- or a volumetric crop,- or twin row with seed spacings below 61⁄2in,this section of the manual, and the sprocket indexingcharts, do not apply to your operations.

If the initial indexing does not provide equal spacing,see “Indexing Fine Adjustment” on page 42.

Refer to Figure 7

1. Find the chart for your row spacing, meter fingercount and desired seed population. Note the “RearMeter Sprocket Tooth #” value in the far right col-umn.

2. Remove both meters of a row unit pair. Note thattooth 1 and many of the other teeth on the drivensprockets , are stamped with a tooth number.

On front row unit:

3. Relax idlers on front meter drive by lifting thespring off the rear post .

4. Lift chain off driven sprocket , and rotate sprocketso that tooth 1 is as close as possible to straight up(top dead center).

5. Re-engage chain and idlers, making sure chain istaut at top, and that sprocket tooth 1 has not shiftedoff TDC.

On rear row unit:

6. Relax idlers on rear meter drive by lifting thespring off the rear post .

7. Lift chain off driven sprocket , and rotate sprocketso that the tooth number called for in the chart is atTDC (or is the same as the front row sprocket).

8. Re-engage chain and idlers, making sure chain istaut at top, and that the designated sprocket toothhas not shifted off TDC.

9. Re-install meters. No particular wheel orientation isrequired during meter installation. The meterengagement is symmetrical, and the results identi-cal no matter how the coupler captures the metershaft.

• •

• • •

• • •

• • •

Indexed - deliberate pair spacing provides maximum plant separation

Non-Indexed - arbitrary pair spacing

Figure 7Sprocket Indexing

25417

12 3

5

46

1 2

3

4

1

5

6

2

12/02/2009 401-312B


30in Rows, 6-Finger Indexing

NOTE: This chart is for indexing finger pickup meter sprockets only!!! Indexing sprockets will help time twin rows to drop seeds in an alternating sequence. This chart is NOT a seed rate chart.

Twin Row 30" 6 Finger Meter Indexing ChartFront Meter Rear Meter

Sprocket Tooth # Sprocket Tooth #15300 16900 27.3 24.7 1 716900 18400 24.7 22.7 1 1018400 20000 22.7 20.9 1 1320000 21600 20.9 19.4 1 1621600 23200 19.4 18.0 1 1923200 24700 18.0 16.9 1 324700 26300 16.9 15.9 1 626300 27900 15.9 15.0 1 927900 29400 15.0 14.2 1 1229400 31000 14.2 13.5 1 1531000 32600 13.5 12.8 1 1832600 34200 12.8 12.2 1 234200 35700 12.2 11.7 1 535700 37300 11.7 11.2 1 837300 38900 11.2 10.8 1 1138900 40400 10.8 10.4 1 1440400 42000 10.4 10.0 1 1742000 43600 10.0 9.6 1 143600 45200 9.6 9.3 1 445200 46700 9.3 9.0 1 746700 48200 9.0 8.7 1 1048200 49900 8.7 8.4 1 1349900 51400 8.4 8.1 1 1651400 54000 8.1 7.7 1 19

NOTE: If rear row does not appear centered between front row seeds, small adjustmentmay be made to the stagger. Refer to "Adjustments to Seed Stagger on 6 Finger Meters."

NOTE: Indexing finger pickup meters can be done with the drill in planting position or with the drill raised (all openers in their lowest position).

1. Pick the planting population which you want to plant from the chart above.

NOTE: When indexing sprockets, the top side of the meter drive chain must be tight.

2. Set the front row meter drive sprockets so the tooth stamped #1 is straight up.

3. Set the rear row meter drive sprockets to match the number from the chart above. Be sure

Population Range Seed Spacing Range

the number is straight up.

401-312B 12/02/2009





Sprocket Tooth # Sprocket Tooth #18400 20000 22.7 20.9 1 720000 21600 20.9 19.4 1 1821600 23200 19.4 18.0 1 1023200 24700 18.0 16.9 1 224700 26100 16.9 16.0 1 1326100 27900 16.0 15.0 1 527900 29400 15.0 14.2 1 1629400 31000 14.2 13.5 1 831000 32600 13.5 12.8 1 1932600 34100 12.8 12.3 1 1134100 35700 12.3 11.7 1 335700 37300 11.7 11.2 1 1437300 38900 11.2 10.8 1 638900 40500 10.8 10.3 1 1740500 41900 10.3 10.0 1 941900 43700 10.0 9.6 1 143700 45100 9.6 9.3 1 1245100 46700 9.3 9.0 1 446700 48300 9.0 8.7 1 1548300 49900 8.7 8.4 1 749900 51400 8.4 8.1 1 1851400 52900 8.1 7.9 1 1052900 54500 7.9 7.7 1 254500 56200 7.7 7.4 1 1356200 57800 7.4 7.2 1 557800 59300 7.2 7.1 1 1659300 60900 7.1 6.9 1 860900 62400 6.9 6.7 1 1962400 64000 6.7 6.5 1 11



1. Pick the planting population which you want to plant from the chart above.NOTE: When indexing sprockets, the top side of the meter drive chain must be tight.2. Set the front row meter drive sprockets so the tooth stamped #1 is straight up. 3. Set the rear row meter drive sprockets to match the number from the chart above. Be sure



12/02/2009 401-312B














401-312B 12/02/2009


36in Rows, 12-Finger IndexingNOTE: This chart is for indexing finger pickup meter sprockets only!!! Indexing sprockets will help time twin rows to drop seeds in an alternating sequence. This chart is NOT a seed rate chart.



NOTE: If rear row does not appear centered between front row seeds, small adjustmentmay be made to the stagger. Refer to "Adjustments to Seed Stagger on 12 Finger Meters." NOTE: Indexing finger pickup meters can be done with the drill in planting position or with the drill raised (all openers in their lowest position).




12/02/2009 401-312B














401-312B 12/02/2009









12/02/2009 401-312B













401-312B 12/02/2009










12/02/2009 401-312B


Indexing Fine AdjustmentIf, after indexing, twin-row side-to-side seed stagger issubstantially imbalanced, it is possible to make smalladjustments that may correct it.

The procedure is different for 6- and 12-finger meters.

If an adjustment is made, test it on one row pair beforeadjusting the entire planter.

Before making any Indexing Adjustments:

• Check actual planted seed spacing. Seed Spacing isfound by measuring the distance between 25 cor-rectly planted seeds in one row and dividing by 24. (Avisible skip or double is counted as one seed.)

• Make sure current rear sprocket index numbermatches the number in the indexing chart for actualseed spacing being planted.

6-Finger Meter Stagger AdjustmentFind your current indexing value row in the charts.

Each (sprocket tooth) number directly above or belowthe current rear meter sprocket setting in the right mostcolumn of the seed indexing chart represents a smallmovement of the rear row seed relative to the front rowseed.

Changing rear your sprocket to the next number up inthe chart retards, moving each rear row seed back asmall amount.

Changing rear sprocket to the next number down in thechart advances, moving each rear row seed ahead asmall amount.

Example 1: The 6 Finger (Twin Row 30in) plantingpopulation is 29900 or 14in seed spacing. The chartsetting for the rear sprocket is (15). Each rear rowseed should fall 7in behind the front row seed.

If each rear row seed measures only 6in behind thefront row seed, reset the rear meter sprocket to thenext number up in the chart (12). This will move therear seeds back to make the stagger closer to 7in.

Example 2: The 6 Finger (Twin Row 30in) plantingpopulation is 29900 or 14in seed spacing. The chartsetting for the rear sprocket is (15). Each rear rowseed should fall 7in behind front row seed.

If each rear row seed measures 8in behind the frontrow seed, reset the rear meter sprocket to the nextnumber down in the chart (18). This will move the rearseeds ahead to make the stagger closer to 7in.

••

•••

•••Desired seed stagger

Rear unit needs to be retarded

•

••••

•

•

•••

••••Rear unit needs to be advanced

Direction of Travel ☞

eter Indexing ChartFront Meter Rear Meter

Sprocket Tooth # Sprocket Tooth #4.7 1 72.7 1 100.9 1 139.4 1 168.0 1 196.9 1 35.9 1 65.0 1 94.2 1 123.5 1 152.8 1 182.2 1 2

7 1 5

ange

Advance ☞

Retard ☞

Current ☞

401-312B 12/02/2009


12-Finger Meter Stagger AdjustmentBefore making any Indexing Adjustments, check actualplanted seed spacing. Seed Spacing is found by mea-suring the distance between 25 correctly plantedseeds in one row and dividing by 24. (A visible skip ordouble should be counted as one seed.) Make surecurrent rear sprocket index number matches the num-ber in the indexing chart for actual seed spacing beingplanted.

Find your current indexing value row in the charts.

Each (sprocket tooth) number directly above or belowthe current rear meter sprocket setting in the right mostcolumn of the seed indexing chart represents a smallmovement of the rear row seed relative to the front rowseed.

Changing rear your sprocket to the next number downin the chart retards, moving each rear row seed back asmall amount.

Changing rear sprocket to the next number up in thechart advances, moving each rear row seed ahead asmall amount.

Example 1: The 12 Finger (Twin Row 30in) plantingpopulation is 34800 or 12in seed spacing. The chartsetting for the rear sprocket is (3). Each rear row seedshould fall 6in behind the front row seed.

If each rear row seed measures 7in behind the frontrow seed, reset the rear meter sprocket to the nextnumber up in the chart (11). This will move the rearseeds ahead and make the stagger closer to 6in.

Example 2: The 12 Finger (Twin Row 30in) plantingpopulation is 34800 or 12in seed spacing. The chartsetting for the rear sprocket is (3). Each rear row seedshould fall 6in behind the front row seed.

If each rear row seed measures 5in behind the frontrow seed, reset the rear meter sprocket to the nextnumber down in the chart (14). This will move the rearseeds back to make the stagger closer to 6in.

••

•••

•••Desired seed stagger

Rear unit needs to be retarded

•

••••

•

•

•••

••••Rear unit needs to be advanced

Direction of Travel ☞

Meter Indexing ChartFront Meter Rear Meter

Sprocket Tooth # Sprocket Tooth #20.9 1 719.4 1 1818.0 1 1016.9 1 216.0 1 1315.0 1 514.2 1 1613.5 1 812.8 1 1912.3 1 1111.7 1 311.2 1 1410.8 1 610.3 1 17

Range

Advance ☞

Retard ☞

Current ☞

12/02/2009 401-312B


Singulating Meter Planting

Singulating meter planting rate is determined by:

• crop and seed variant

• meter wheel selection, and

• meter drive configuration

There are no other adjustments.

Reading a Singulated Rate ChartHydraulic or Ground Drive1. Consult the chart for your crop, meter wheel/cell

count, and row spacing. Some charts have twopages.

2. Note whether talc, or talc and graphite are required.See “Seed Lubricants” on page 67 for seed lubri-cant information.

3. Find the columns for your row spacing.

4. Find the desired seed population range (or seedspacing).

5. Note the maximum ground speed for that popula-tion.

With hydraulic meter drive, enter the population in theseed monitor. With ground drive, configure the sprock-ets.

Ground Drive6. The Range and Upper Drive sprockets are at the

top of the columns for the row spacing.

7. The Transmission sprockets are in the table rows,found to the left of the Population.

MILO Page 1 of 2Singulating

135 Cell Wheel

S ngulat ng135 Cell Wheel

TALC & GRAPHITEREQUIRED

Twin Row 30" Twin Row 36" T

15" Row Spacing

nations Seed Seed Planting Seed Planting Seed PlaPopulation Spacing Speed Spacing Speed Spacing Sp

Driven (seeds/acre) (inches) (mph) (inches) (mph) (inches) (m

28 71,027 5 9 8 4.9 8 4.627 73,658 5.7 8 4.7 8 4.526 76 491 5 5 8 4 6 8 4 3

mission Maximum Maximum Maxnations Seed Seed Planting Seed Planting Seed Pla

Population Spacing Speed Spacing Speed Spacing SpDriven (seeds/acre) (inches) (mph) (inches) (mph) (inches) (m

28 71,027 5.9 8 4 9 8 4.627 73,658 5.7 8 4.7 8 4.5

Twin Row 30" Twin Row 36"

Range Sprockets: Range Sprockets:Driver = 15 Driver = 18Driven = 38 Driven = 38

Sprocket: 18 Sprocket: 18 Sp

Transmission Maximum MaximumCombinations Seed Seed Planting Seed Planting

Population Spacing Speed Spacing Speed SDriver Driven (seeds/acre) (inches) (mph) (inches) (mph) (

17 28 71,027 5.9 8 4.9 817 27 73,658 5.7 8 4.7 817 26 76,491 5.5 8 4.6 8

15" Row Spacing

Upper Drive Upper Drive U

401-312B 12/02/2009


Corn3PT YIELD PRO 1225 - 1625 CORN403-127D Round Corn 1400-1900 Kernels/lb. Singulating403-128D Round Corn 1700-2200 Kernels/lb. 28 Cell Wheel403-131D Flat Corn 1500-1675 Kernels/lb. TALC REQUIRED403-132D Flat Corn 1625-1800 Kernels/lb.

Twin Row 30" Twin Row 36" Twin Row 38"

Range Sprockets: Range Sprockets: Range Sprockets:Range Sprockets:Driver = 15 Driver = 18 Driver = 19 Driver = 20Driven = 30 Driven = 30 Driven = 30 Driven = 30

Sprocket: 18 Sprocket: 18 Sprocket: 18 Sprocket: 18

Transmission Maximum Maximum Maximum MaximumCombinations Seed Seed Planting Seed Planting Seed Planting Seed Planting

Population Spacing Speed Spacing Speed Spacing Speed Spacing SpeedDriver Driven (seeds/acre) (inches) (mph) (inches) (mph) (inches) (mph) (inches) (mph)

17 28 18,660 22.4 8 18.7 8 17.7 8 16 8 817 27 19,351 21.6 8 18.0 8 17.1 8 16 2 817 26 20,095 20.8 8 17.3 8 16.4 8 15 6 819 28 20,855 20.1 8 16.7 8 15.8 8 15 0 717 25 20,899 20.0 8 16.7 8 15.8 8 15 0 719 27 21,628 19.3 8 16.1 8 15.3 8 14 5 717 24 21,770 19.2 8 16.0 8 15.2 8 14.4 719 26 22,460 18.6 8 15.5 8 14.7 7 14 0 717 23 22,717 18.4 8 15.3 8 14.5 7 13 8 719 25 23,358 17.9 8 14.9 7 14.1 7 13.4 719 24 24,331 17.2 8 14.3 7 13.6 7 12 9 623 28 25,246 16.6 8 13.8 7 13.1 6 12.4 619 23 25,389 16.5 8 13.7 7 13.0 6 12.4 623 27 26,181 16.0 8 13.3 7 12.6 6 12 0 624 28 26,344 15.9 8 13.2 7 12.5 6 11 9 623 26 27,188 15.4 8 12.8 6 12.1 6 11 5 624 27 27,319 15.3 8 12.8 6 12.1 6 11 5 625 28 27,441 15.2 8 12.7 6 12.0 6 11.4 617 19 27,499 15.2 8 12.7 6 12.0 6 11.4 623 25 28,275 14.8 7 12.3 6 11.7 6 11.1 524 26 28,370 14.7 7 12.3 6 11.6 6 11.1 525 27 28,458 14.7 7 12.2 6 11.6 6 11 0 526 28 28,539 14.7 7 12.2 6 11.6 6 11 0 523 24 29,454 14.2 7 11.8 6 11.2 5 10 6 524 25 29,505 14.2 7 11.8 6 11.2 5 10 6 525 26 29,552 14.2 7 11.8 6 11.2 5 10 6 526 27 29,596 14.1 7 11.8 6 11.2 5 10 6 527 28 29,636 14.1 7 11.8 6 11.1 5 10 6 523 23 30,734 13.6 7 11.3 6 10.7 5 10 2 528 27 31,872 13.1 6 10.9 5 10.4 5 9.8 527 26 31,916 13.1 6 10.9 5 10.3 5 9.8 526 25 31,963 13.1 6 10.9 5 10.3 5 9.8 525 24 32,015 13.1 6 10.9 5 10.3 5 9.8 524 23 32,070 13.0 6 10.9 5 10.3 5 9.8 528 26 33,098 12.6 6 10.5 5 10.0 5 9.5 527 25 33,193 12.6 6 10.5 5 9 9 5 9.4 526 24 33,295 12.6 6 10.5 5 9 9 5 9.4 425 23 33,407 12.5 6 10.4 5 9 9 5 9.4 419 17 34,350 12.2 6 10.1 5 9 6 5 9.1 428 25 34,422 12.1 6 10.1 5 9 6 5 9.1 427 24 34,576 12.1 6 10.1 5 9 5 5 9.1 426 23 34,743 12.0 6 10.0 5 9 5 5 9.0 428 24 35,856 11.7 6 9.7 5 9 2 4 8.7 427 23 36,079 11.6 6 9.7 5 9 2 4 8.7 423 19 37,204 11.2 5 9.4 4 8 9 4 8.4 428 23 37,415 11.2 5 9.3 4 8 8 4 8.4 424 19 38,822 10.8 5 9.0 4 8 5 4 8.1 425 19 40,440 10.3 5 8.6 4 8 2 4 7.8 423 17 41,581 10.1 5 8.4 4 7 9 4 7.5 326 19 42,057 9.9 5 8.3 4 7 8 4 7.5 324 17 43,389 9.6 5 8.0 4 7 6 4 7.2 327 19 43,675 9.6 5 8.0 4 7 6 4 7.2 325 17 45,197 9.3 4 7.7 4 7 3 3 6.9 328 19 45,292 9.2 4 7.7 4 7 3 3 6.9 326 17 47,005 8.9 4 7.4 3 7 0 3 6.7 327 17 48,813 8.6 4 7.1 3 6 8 3 6.4 328 17 50,621 8.3 4 6.9 3 6 5 3 6.2 3

Upper Drive Upper Drive Upper Drive Upper Drive

Twin Row 40"20" Row Spacing15" Row Spacing

12/02/2009 401-312B


Cotton (page 1 of 2)

3PT YIELD PRO 1225 - 1625 COTTON Page 1 of 2403-133D 4000-4600 seeds/pound Singulating403-134D 4600-5200 seeds/pound 120 Cell Wheel403-135D 5200-6000 seeds/pound TALC REQUIRED


Range Sprockets: Range Sprockets: Range SprocketsRange Sprockets:Driver = 15 Driver = 18 Driver = 19 Driver = 20Driven = 38 Driven = 38 Driven = 38 Driven = 38




17 28 63,135 6.6 8 5 5 8 5 2 8 5.0 817 27 65,474 6.4 8 5 3 8 5 0 8 4.8 817 26 67,992 6.2 8 5.1 8 4 9 8 4.6 819 28 70,563 5.9 8 4 9 8 4.7 8 4.4 817 25 70,712 5.9 8 4 9 8 4.7 8 4.4 819 27 73,176 5.7 8 4 8 8 4 5 8 4.3 817 24 73,658 5.7 8 4.7 8 4 5 8 4.3 819 26 75,991 5.5 8 4 6 8 4 3 8 4.1 817 23 76,860 5.4 8 4 5 8 4 3 8 4.1 819 25 79,031 5.3 8 4.4 8 4 2 8 4.0 819 24 82,324 5.1 8 4 2 8 4 0 8 3.8 823 28 85,418 4.9 8 4.1 8 3 9 8 3.7 819 23 85,903 4.9 8 4.1 8 3 8 8 3.7 823 27 88,582 4.7 8 3 9 8 3.7 8 3.5 824 28 89,132 4.7 8 3 9 8 3.7 8 3.5 823 26 91,989 4.5 8 3 8 8 3 6 8 3.4 824 27 92,433 4.5 8 3 8 8 3 6 8 3.4 825 28 92,846 4.5 8 3 8 8 3 6 8 3.4 817 19 93,042 4.5 8 3.7 8 3 5 8 3.4 823 25 95,669 4.4 8 3 6 8 3 5 8 3.3 824 26 95,989 4.4 8 3 6 8 3.4 8 3.3 825 27 96,285 4.3 8 3 6 8 3.4 8 3.3 826 28 96,560 4.3 8 3 6 8 3.4 8 3.2 823 24 99,655 4.2 8 3 5 8 3 3 8 3.1 724 25 99,828 4.2 8 3 5 8 3 3 8 3.1 725 26 99,988 4.2 8 3 5 8 3 3 8 3.1 726 27 100,136 4.2 8 3 5 8 3 3 8 3.1 727 28 100,274 4.2 8 3 5 8 3 3 8 3.1 723 23 103,988 4.0 8 3.4 8 3 2 7 3.0 728 27 107,839 3.9 8 3 2 8 3.1 7 2.9 727 26 107,987 3.9 8 3 2 8 3.1 7 2.9 726 25 108,147 3.9 8 3 2 8 3.1 7 2.9 725 24 108,320 3.9 8 3 2 8 3 0 7 2.9 724 23 108,509 3.9 8 3 2 8 3 0 7 2.9 728 26 111,987 3.7 8 3.1 7 2 9 7 2.8 727 25 112,307 3.7 8 3.1 7 2 9 7 2.8 626 24 112,653 3.7 8 3.1 7 2 9 7 2.8 625 23 113,030 3.7 8 3.1 7 2 9 7 2.8 619 17 116,221 3.6 8 3 0 7 2 8 7 2.7 628 25 116,466 3.6 8 3 0 7 2 8 7 2.7 627 24 116,986 3.6 8 3 0 7 2 8 7 2.7 626 23 117,551 3.6 8 3 0 7 2 8 7 2.7 628 24 121,319 3.4 8 2 9 7 2.7 6 2.6 627 23 122,072 3.4 8 2 9 7 2.7 6 2.6 623 19 125,880 3.3 8 2 8 6 2 6 6 2.5 628 23 126,594 3.3 8 2 8 6 2 6 6 2.5 624 19 131,353 3.2 7 2.7 6 2 5 6 2.4 525 19 136,826 3.1 7 2 5 6 2.4 6 2.3 523 17 140,689 3.0 7 2 5 6 2 3 5 2.2 526 19 142,299 2.9 7 2.4 6 2 3 5 2.2 524 17 146,806 2.8 7 2.4 5 2 2 5 2.1 527 19 147,772 2.8 7 2.4 5 2 2 5 2.1 525 17 152,923 2.7 6 2 3 5 2 2 5 2.1 528 19 153,245 2.7 6 2 3 5 2 2 5 2.0 526 17 159,040 2.6 6 2 2 5 2.1 5 2.0 427 17 165,157 2.5 6 2.1 5 2 0 4 1.9 428 17 171,274 2.4 6 2 0 5 1 9 4 1.8 4



401-312B 12/02/2009


Cotton (page 2 of 2)

3PT YIELD PRO 1225 - 1625 COTTON Page 2 of 2403-133D 4000-4600 seeds/pound Singulating403-134D 4600-5200 seeds/pound 120 Cell Wheel403-135D 5200-6000 seeds/pound TALC REQUIRED

38" Row Spacing 40" Row Spacing

Range Sprockets:Driver = 15 Driver = 18 Driver = 19 Driver = 20Driven = 38 Driven = 38 Driven = 38 Driven = 38

Upper DriveSprocket: 18 Sprocket: 18 Sprocket: 18 Sprocket: 18



17 28 31,568 6.6 8 5.5 8 5.2 8 5.0 817 27 32,737 6.4 8 5.3 8 5.0 8 4.8 817 26 33,996 6.2 8 5.1 8 4.9 8 4.6 819 28 35,282 5.9 8 4.9 8 4.7 8 4.4 817 25 35,356 5.9 8 4.9 8 4.7 8 4.4 819 27 36,588 5.7 8 4.8 8 4.5 8 4.3 817 24 36,829 5.7 8 4.7 8 4.5 8 4.3 819 26 37,995 5.5 8 4.6 8 4.3 8 4.1 817 23 38,430 5.4 8 4.5 8 4.3 8 4.1 819 25 39,515 5.3 8 4.4 8 4.2 8 4.0 819 24 41,162 5.1 8 4.2 8 4.0 8 3.8 823 28 42,709 4.9 8 4.1 8 3.9 8 3.7 819 23 42,951 4.9 8 4.1 8 3.8 8 3.7 823 27 44,291 4.7 8 3.9 8 3.7 8 3.5 824 28 44,566 4.7 8 3.9 8 3.7 8 3.5 823 26 45,995 4.5 8 3.8 8 3.6 8 3.4 824 27 46,217 4.5 8 3.8 8 3.6 8 3.4 825 28 46,423 4.5 8 3.8 8 3.6 8 3.4 817 19 46,521 4.5 8 3.7 8 3.5 8 3.4 823 25 47,834 4.4 8 3.6 8 3.5 8 3.3 824 26 47,994 4.4 8 3.6 8 3.4 8 3.3 825 27 48,142 4.3 8 3.6 8 3.4 8 3.3 826 28 48,280 4.3 8 3.6 8 3.4 8 3.2 823 24 49,827 4.2 8 3.5 8 3.3 8 3.1 724 25 49,914 4.2 8 3.5 8 3.3 8 3.1 725 26 49,994 4.2 8 3.5 8 3.3 8 3.1 726 27 50,068 4.2 8 3.5 8 3.3 8 3.1 727 28 50,137 4.2 8 3.5 8 3.3 8 3.1 723 23 51,994 4.0 8 3.4 8 3.2 7 3.0 728 27 53,919 3.9 8 3.2 8 3.1 7 2.9 727 26 53,994 3.9 8 3.2 8 3.1 7 2.9 726 25 54,074 3.9 8 3.2 8 3.1 7 2.9 725 24 54,160 3.9 8 3.2 8 3.0 7 2.9 724 23 54,254 3.9 8 3.2 8 3.0 7 2.9 728 26 55,993 3.7 8 3.1 7 2.9 7 2.8 727 25 56,153 3.7 8 3.1 7 2.9 7 2.8 626 24 56,327 3.7 8 3.1 7 2.9 7 2.8 625 23 56,515 3.7 8 3.1 7 2.9 7 2.8 619 17 58,111 3.6 8 3.0 7 2.8 7 2.7 628 25 58,233 3.6 8 3.0 7 2.8 7 2.7 627 24 58,493 3.6 8 3.0 7 2.8 7 2.7 626 23 58,776 3.6 8 3.0 7 2.8 7 2.7 628 24 60,659 3.4 8 2.9 7 2.7 6 2.6 627 23 61,036 3.4 8 2.9 7 2.7 6 2.6 623 19 62,940 3.3 8 2.8 6 2.6 6 2.5 628 23 63,297 3.3 8 2.8 6 2.6 6 2.5 624 19 65,676 3.2 7 2.7 6 2.5 6 2.4 525 19 68,413 3.1 7 2.5 6 2.4 6 2.3 523 17 70,345 3.0 7 2.5 6 2.3 5 2.2 526 19 71,149 2.9 7 2.4 6 2.3 5 2.2 524 17 73,403 2.8 7 2.4 5 2.2 5 2.1 527 19 73,886 2.8 7 2.4 5 2.2 5 2.1 525 17 76,461 2.7 6 2.3 5 2.2 5 2.1 528 19 76,622 2.7 6 2.3 5 2.2 5 2.0 526 17 79,520 2.6 6 2.2 5 2.1 5 2.0 427 17 82,578 2.5 6 2.1 5 2.0 4 1.9 428 17 85,637 2.4 6 2.0 5 1.9 4 1.8 4

Range Sprockets:

Upper Drive Upper Drive Upper Drive

Range Sprockets: Range Sprockets:


12/02/2009 401-312B


Milo (51 Cell Meter) (page 1 of 2)

3PT YIELD PRO 1225 - 1625 MILO Page 1 of 2403-136D 10500-18000 seeds/pound Singulating

51 Cell WheelTALC & GRAPHITE

REQUIRED


Range Sprockets: Range Sprockets: Range Sprockets:Driver = 15 Driver = 18 Driver = 19 Driver = 20Driven = 38 Driven = 38 Driven = 38 Driven = 38




17 28 26,833 15.6 8 13.0 8 12.3 8 11.7 817 27 27,826 15.0 8 12.5 8 11.9 8 11 3 817 26 28,897 14.5 8 12.1 8 11.4 8 10 9 819 28 29,989 13.9 8 11.6 8 11.0 8 10 5 817 25 30,052 13.9 8 11.6 8 11.0 8 10.4 819 27 31,100 13.4 8 11.2 8 10.6 8 10.1 817 24 31,305 13.4 8 11.1 8 10.5 8 10 0 819 26 32,296 12.9 8 10.8 8 10.2 8 9.7 817 23 32,666 12.8 8 10.7 8 10.1 8 9.6 819 25 33,588 12.5 8 10.4 8 9 8 8 9.3 819 24 34,987 12.0 8 10.0 8 9.4 8 9.0 823 28 36,303 11.5 8 9 6 8 9.1 8 8.6 819 23 36,509 11.5 8 9 5 8 9 0 8 8.6 823 27 37,647 11.1 8 9 3 8 8 8 8 8.3 824 28 37,881 11.0 8 9 2 8 8.7 8 8.3 723 26 39,095 10.7 8 8 9 8 8.4 8 8.0 724 27 39,284 10.6 8 8 9 8 8.4 8 8.0 725 28 39,460 10.6 8 8 8 8 8.4 8 7.9 717 19 39,543 10.6 8 8 8 8 8 3 8 7.9 723 25 40,659 10.3 8 8 6 8 8.1 7 7.7 724 26 40,795 10.3 8 8 5 8 8.1 7 7.7 725 27 40,921 10.2 8 8 5 8 8.1 7 7.7 726 28 41,038 10.2 8 8 5 8 8 0 7 7.6 723 24 42,353 9.9 8 8 2 7 7 8 7 7.4 724 25 42,427 9.9 8 8 2 7 7 8 7 7.4 725 26 42,495 9.8 8 8 2 7 7 8 7 7.4 726 27 42,558 9.8 8 8 2 7 7 8 7 7.4 727 28 42,616 9.8 8 8 2 7 7.7 7 7.4 723 23 44,195 9.5 8 7 9 7 7 5 7 7.1 628 27 45,832 9.1 8 7 6 7 7 2 6 6.8 627 26 45,895 9.1 8 7 6 7 7 2 6 6.8 626 25 45,963 9.1 8 7 6 7 7 2 6 6.8 625 24 46,036 9.1 8 7 6 7 7 2 6 6.8 624 23 46,116 9.1 8 7 6 7 7 2 6 6.8 628 26 47,594 8.8 8 7 3 7 6 9 6 6.6 627 25 47,730 8.8 8 7 3 7 6 9 6 6.6 626 24 47,878 8.7 8 7 3 7 6 9 6 6.6 625 23 48,038 8.7 8 7 3 7 6 9 6 6.5 619 17 49,394 8.5 8 7.1 6 6.7 6 6.3 628 25 49,498 8.4 8 7 0 6 6.7 6 6.3 627 24 49,719 8.4 8 7 0 6 6 6 6 6.3 626 23 49,959 8.4 8 7 0 6 6 6 6 6.3 628 24 51,561 8.1 7 6 8 6 6.4 6 6.1 527 23 51,881 8.1 7 6.7 6 6.4 6 6.0 523 19 53,499 7.8 7 6 5 6 6 2 5 5.9 528 23 53,802 7.8 7 6 5 6 6.1 5 5.8 524 19 55,825 7.5 7 6 2 6 5 9 5 5.6 525 19 58,151 7.2 6 6 0 5 5.7 5 5.4 523 17 59,793 7.0 6 5 8 5 5 5 5 5.2 526 19 60,477 6.9 6 5 8 5 5 5 5 5.2 524 17 62,393 6.7 6 5 6 5 5 3 5 5.0 427 19 62,803 6.7 6 5 5 5 5 3 5 5.0 425 17 64,992 6.4 6 5.4 5 5.1 4 4.8 428 19 65,129 6.4 6 5.4 5 5.1 4 4.8 426 17 67,592 6.2 5 5 2 4 4 9 4 4.6 427 17 70,192 6.0 5 5 0 4 4.7 4 4.5 428 17 72,791 5.7 5 4 8 4 4 5 4 4.3 4

15" Row SpacingTwin Row 40"

20" Row SpacingRange Sprockets:


401-312B 12/02/2009





REQUIRED






17 28 26,833 7 8 7 6.5 6 6.2 5 5.8 517 27 27,826 7 5 7 6.3 6 5.9 5 5.6 517 26 28,897 7 2 6 6.0 5 5.7 5 5.4 519 28 29,989 7 0 6 5.8 5 5.5 5 5.2 517 25 30,052 7 0 6 5.8 5 5.5 5 5.2 519 27 31,100 6.7 6 5.6 5 5.3 5 5.0 417 24 31,305 6.7 6 5.6 5 5.3 5 5.0 419 26 32,296 6 5 6 5.4 5 5.1 4 4.9 417 23 32,666 6.4 6 5.3 5 5.1 4 4.8 419 25 33,588 6 2 6 5.2 5 4.9 4 4.7 419 24 34,987 6 0 5 5.0 4 4.7 4 4.5 423 28 36,303 5 8 5 4.8 4 4.5 4 4.3 419 23 36,509 5.7 5 4.8 4 4.5 4 4.3 423 27 37,647 5 6 5 4.6 4 4.4 4 4.2 424 28 37,881 5 5 5 4.6 4 4.4 4 4.1 323 26 39,095 5 3 5 4.5 4 4.2 4 4.0 324 27 39,284 5 3 5 4.4 4 4.2 4 4.0 325 28 39,460 5 3 5 4.4 4 4.2 4 4.0 317 19 39,543 5 3 5 4.4 4 4.2 4 4.0 323 25 40,659 5.1 4 4.3 4 4.1 3 3.9 324 26 40,795 5.1 4 4.3 4 4.0 3 3.8 325 27 40,921 5.1 4 4.3 4 4.0 3 3.8 326 28 41,038 5.1 4 4.2 4 4.0 3 3.8 323 24 42,353 4 9 4 4.1 3 3.9 3 3.7 324 25 42,427 4 9 4 4.1 3 3.9 3 3.7 325 26 42,495 4 9 4 4.1 3 3.9 3 3.7 326 27 42,558 4 9 4 4.1 3 3.9 3 3.7 327 28 42,616 4 9 4 4.1 3 3.9 3 3.7 323 23 44,195 4.7 4 3.9 3 3.7 3 3.5 328 27 45,832 4 6 4 3.8 3 3.6 3 3.4 327 26 45,895 4 6 4 3.8 3 3.6 3 3.4 326 25 45,963 4 5 4 3.8 3 3.6 3 3.4 325 24 46,036 4 5 4 3.8 3 3.6 3 3.4 324 23 46,116 4 5 4 3.8 3 3.6 3 3.4 328 26 47,594 4.4 4 3.7 3 3.5 3 3.3 327 25 47,730 4.4 4 3.7 3 3.5 3 3.3 326 24 47,878 4.4 4 3.6 3 3.4 3 3.3 325 23 48,038 4.4 4 3.6 3 3.4 3 3.3 319 17 49,394 4 2 4 3.5 3 3.3 3 3.2 328 25 49,498 4 2 4 3.5 3 3.3 3 3.2 327 24 49,719 4 2 4 3.5 3 3.3 3 3.2 326 23 49,959 4 2 4 3.5 3 3.3 3 3.1 328 24 51,561 4.1 3 3.4 3 3.2 3 3.0 227 23 51,881 4 0 3 3.4 3 3.2 3 3.0 223 19 53,499 3 9 3 3.3 3 3.1 2 2.9 228 23 53,802 3 9 3 3.2 3 3.1 2 2.9 224 19 55,825 3.7 3 3.1 3 3.0 2 2.8 225 19 58,151 3 6 3 3.0 2 2.8 2 2.7 223 17 59,793 3 5 3 2.9 2 2.8 2 2.6 226 19 60,477 3 5 3 2.9 2 2.7 2 2.6 224 17 62,393 3.4 3 2.8 2 2.6 2 2.5 227 19 62,803 3 3 3 2.8 2 2.6 2 2.5 225 17 64,992 3 2 3 2.7 2 2.5 2 2.4 228 19 65,129 3 2 3 2.7 2 2.5 2 2.4 226 17 67,592 3.1 2 2.6 2 2.4 2 2.3 227 17 70,192 3 0 2 2.5 2 2.4 2 2.2 228 17 72,791 2 9 2 2.4 2 2.3 2 2.2 2

Upper Drive

Range Sprockets:

Upper Drive Upper Drive



12/02/2009 401-312B





REQUIRED






17 28 53,665 7.8 8 6.5 8 6 2 8 5 8 817 27 55,653 7.5 8 6.3 8 5 9 8 5 6 817 26 57,793 7.2 8 6.0 8 5.7 8 5.4 819 28 59,979 7.0 8 5.8 8 5 5 8 5 2 817 25 60,105 7.0 8 5.8 8 5 5 8 5 2 819 27 62,200 6.7 8 5.6 8 5 3 8 5 0 817 24 62,609 6.7 8 5.6 8 5 3 8 5 0 819 26 64,592 6.5 8 5.4 8 5.1 8 4 9 817 23 65,331 6.4 8 5.3 8 5.1 8 4 8 819 25 67,176 6.2 8 5.2 8 4 9 8 4.7 819 24 69,975 6.0 8 5.0 8 4.7 8 4 5 823 28 72,606 5.8 8 4.8 8 4 5 8 4 3 819 23 73,017 5.7 8 4.8 8 4 5 8 4 3 823 27 75,295 5.6 8 4.6 8 4.4 8 4 2 824 28 75,762 5.5 8 4.6 8 4.4 8 4.1 723 26 78,191 5.3 8 4.5 8 4 2 8 4 0 724 27 78,568 5.3 8 4.4 8 4 2 8 4 0 725 28 78,919 5.3 8 4.4 8 4 2 8 4 0 717 19 79,085 5.3 8 4.4 8 4 2 8 4 0 723 25 81,318 5.1 8 4.3 8 4.1 7 3 9 724 26 81,590 5.1 8 4.3 8 4 0 7 3 8 725 27 81,842 5.1 8 4.3 8 4 0 7 3 8 726 28 82,076 5.1 8 4.2 8 4 0 7 3 8 723 24 84,707 4.9 8 4.1 7 3 9 7 3.7 724 25 84,854 4.9 8 4.1 7 3 9 7 3.7 725 26 84,990 4.9 8 4.1 7 3 9 7 3.7 726 27 85,116 4.9 8 4.1 7 3 9 7 3.7 727 28 85,233 4.9 8 4.1 7 3 9 7 3.7 723 23 88,389 4.7 8 3.9 7 3.7 7 3 5 628 27 91,663 4.6 8 3.8 7 3 6 6 3.4 627 26 91,789 4.6 8 3.8 7 3 6 6 3.4 626 25 91,925 4.5 8 3.8 7 3 6 6 3.4 625 24 92,072 4.5 8 3.8 7 3 6 6 3.4 624 23 92,232 4.5 8 3.8 7 3 6 6 3.4 628 26 95,189 4.4 8 3.7 7 3 5 6 3 3 627 25 95,461 4.4 8 3.7 7 3 5 6 3 3 626 24 95,755 4.4 8 3.6 7 3.4 6 3 3 625 23 96,075 4.4 8 3.6 7 3.4 6 3 3 619 17 98,788 4.2 8 3.5 6 3 3 6 3 2 628 25 98,996 4.2 8 3.5 6 3 3 6 3 2 627 24 99,438 4.2 8 3.5 6 3 3 6 3 2 626 23 99,919 4.2 8 3.5 6 3 3 6 3.1 628 24 103,121 4.1 7 3.4 6 3 2 6 3 0 527 23 103,762 4.0 7 3.4 6 3 2 6 3 0 523 19 106,998 3.9 7 3.3 6 3.1 5 2 9 528 23 107,605 3.9 7 3.2 6 3.1 5 2 9 524 19 111,650 3.7 7 3.1 6 3 0 5 2 8 525 19 116,302 3.6 6 3.0 5 2 8 5 2.7 523 17 119,586 3.5 6 2.9 5 2 8 5 2 6 526 19 120,954 3.5 6 2.9 5 2.7 5 2 6 524 17 124,785 3.4 6 2.8 5 2 6 5 2 5 427 19 125,606 3.3 6 2.8 5 2 6 5 2 5 425 17 129,984 3.2 6 2.7 5 2 5 4 2.4 428 19 130,258 3.2 6 2.7 5 2 5 4 2.4 426 17 135,184 3.1 5 2.6 4 2.4 4 2 3 427 17 140,383 3.0 5 2.5 4 2.4 4 2 2 428 17 145,583 2.9 5 2.4 4 2 3 4 2 2 4



401-312B 12/02/2009





REQUIRED






17 28 53,665 3 9 7 3.2 6 3.1 5 2.9 517 27 55,653 3 8 7 3.1 6 3.0 5 2.8 517 26 57,793 3 6 6 3.0 5 2.9 5 2.7 519 28 59,979 3 5 6 2.9 5 2.8 5 2.6 517 25 60,105 3 5 6 2.9 5 2.7 5 2.6 519 27 62,200 3.4 6 2.8 5 2.7 5 2.5 417 24 62,609 3 3 6 2.8 5 2.6 5 2.5 419 26 64,592 3 2 6 2.7 5 2.6 4 2.4 417 23 65,331 3 2 6 2.7 5 2.5 4 2.4 419 25 67,176 3.1 6 2.6 5 2.5 4 2.3 419 24 69,975 3 0 5 2.5 4 2.4 4 2.2 423 28 72,606 2 9 5 2.4 4 2.3 4 2.2 419 23 73,017 2 9 5 2.4 4 2.3 4 2.1 423 27 75,295 2 8 5 2.3 4 2.2 4 2.1 424 28 75,762 2 8 5 2.3 4 2.2 4 2.1 323 26 78,191 2.7 5 2.2 4 2.1 4 2.0 324 27 78,568 2.7 5 2.2 4 2.1 4 2.0 325 28 78,919 2 6 5 2.2 4 2.1 4 2.0 317 19 79,085 2 6 5 2.2 4 2.1 4 2.0 323 25 81,318 2 6 4 2.1 4 2.0 3 1.9 324 26 81,590 2 6 4 2.1 4 2.0 3 1.9 325 27 81,842 2 6 4 2.1 4 2.0 3 1.9 326 28 82,076 2 5 4 2.1 4 2.0 3 1.9 323 24 84,707 2 5 4 2.1 3 1.9 3 1.9 324 25 84,854 2 5 4 2.1 3 1.9 3 1.8 325 26 84,990 2 5 4 2.1 3 1.9 3 1.8 326 27 85,116 2 5 4 2.0 3 1.9 3 1.8 327 28 85,233 2 5 4 2.0 3 1.9 3 1.8 323 23 88,389 2.4 4 2.0 3 1.9 3 1.8 328 27 91,663 2 3 4 1.9 3 1.8 3 1.7 327 26 91,789 2 3 4 1.9 3 1.8 3 1.7 326 25 91,925 2 3 4 1.9 3 1.8 3 1.7 325 24 92,072 2 3 4 1.9 3 1.8 3 1.7 324 23 92,232 2 3 4 1.9 3 1.8 3 1.7 328 26 95,189 2 2 4 1.8 3 1.7 3 1.6 327 25 95,461 2 2 4 1.8 3 1.7 3 1.6 326 24 95,755 2 2 4 1.8 3 1.7 3 1.6 325 23 96,075 2 2 4 1.8 3 1.7 3 1.6 319 17 98,788 2.1 4 1.8 3 1.7 3 1.6 328 25 98,996 2.1 4 1.8 3 1.7 3 1.6 327 24 99,438 2.1 4 1.8 3 1.7 3 1.6 326 23 99,919 2.1 4 1.7 3 1.7 3 1.6 328 24 103,121 2 0 3 1.7 3 1.6 3 1.5 227 23 103,762 2 0 3 1.7 3 1.6 3 1.5 223 19 106,998 2 0 3 1.6 3 1.5 2 1.5 228 23 107,605 1 9 3 1.6 3 1.5 2 1.5 224 19 111,650 1 9 3 1.6 3 1.5 2 1.4 225 19 116,302 1 8 3 1.5 2 1.4 2 1.3 223 17 119,586 1.7 3 1.5 2 1.4 2 1.3 226 19 120,954 1.7 3 1.4 2 1.4 2 1.3 224 17 124,785 1.7 3 1.4 2 1.3 2 1.3 227 19 125,606 1.7 3 1.4 2 1.3 2 1.2 225 17 129,984 1 6 3 1.3 2 1.3 2 1.2 228 19 130,258 1 6 3 1.3 2 1.3 2 1.2 226 17 135,184 1 5 2 1.3 2 1.2 2 1.2 227 17 140,383 1 5 2 1.2 2 1.2 2 1.1 228 17 145,583 1.4 2 1.2 2 1.1 2 1.1 2

36" Row Spacing


Upper Drive

Range Sprockets:


30" Row Spacing

12/02/2009 401-312B



3PT YIELD PRO 1225 - 1625 MILO Page 1 of 2403-140D 12000-18000 seeds/pound Singulating403-138D 10500-14000 seeds/pound 135 Cell Wheel







17 28 71,027 5.9 8 4.9 8 4 6 8 4.4 817 27 73,658 5.7 8 4.7 8 4 5 8 4 3 817 26 76,491 5.5 8 4.6 8 4 3 8 4.1 819 28 79,383 5.3 8 4.4 8 4 2 8 4 0 817 25 79,551 5.3 8 4.4 8 4 2 8 3 9 819 27 82,324 5.1 8 4.2 8 4 0 8 3 8 817 24 82,865 5.0 8 4.2 8 4 0 8 3 8 819 26 85,490 4.9 8 4.1 8 3 9 8 3.7 817 23 86,468 4.8 8 4.0 8 3 8 8 3 6 819 25 88,909 4.7 8 3.9 8 3.7 8 3 5 819 24 92,614 4.5 8 3.8 8 3 6 8 3.4 823 28 96,096 4.4 8 3.6 8 3.4 8 3 3 819 23 96,641 4.3 8 3.6 8 3.4 8 3 2 823 27 99,655 4.2 8 3.5 8 3 3 8 3.1 824 28 100,274 4.2 8 3.5 8 3 3 8 3.1 723 26 103,488 4.0 8 3.4 8 3 2 8 3 0 724 27 103,988 4.0 8 3.4 8 3 2 8 3 0 725 28 104,452 4.0 8 3.3 8 3 2 8 3 0 717 19 104,672 4.0 8 3.3 8 3 2 8 3 0 723 25 107,627 3.9 8 3.2 8 3.1 7 2 9 724 26 107,987 3.9 8 3.2 8 3.1 7 2 9 725 27 108,320 3.9 8 3.2 8 3 0 7 2 9 726 28 108,630 3.8 8 3.2 8 3 0 7 2 9 723 24 112,112 3.7 8 3.1 7 2 9 7 2 8 724 25 112,307 3.7 8 3.1 7 2 9 7 2 8 725 26 112,487 3.7 8 3.1 7 2 9 7 2 8 726 27 112,653 3.7 8 3.1 7 2 9 7 2 8 727 28 112,808 3.7 8 3.1 7 2 9 7 2 8 723 23 116,986 3.6 8 3.0 7 2 8 7 2.7 628 27 121,319 3.4 8 2.9 7 2.7 6 2 6 627 26 121,486 3.4 8 2.9 7 2.7 6 2 6 626 25 121,665 3.4 8 2.9 7 2.7 6 2 6 625 24 121,860 3.4 8 2.9 7 2.7 6 2 6 624 23 122,072 3.4 8 2.9 7 2.7 6 2 6 628 26 125,985 3.3 8 2.8 7 2 6 6 2 5 627 25 126,345 3.3 8 2.8 7 2 6 6 2 5 626 24 126,735 3.3 8 2.7 7 2 6 6 2 5 625 23 127,159 3.3 8 2.7 7 2 6 6 2 5 619 17 130,749 3.2 8 2.7 6 2 5 6 2.4 628 25 131,024 3.2 8 2.7 6 2 5 6 2.4 627 24 131,609 3.2 8 2.6 6 2 5 6 2.4 626 23 132,245 3.2 8 2.6 6 2 5 6 2.4 628 24 136,484 3.1 7 2.6 6 2.4 6 2 3 527 23 137,331 3.0 7 2.5 6 2.4 6 2 3 523 19 141,615 3.0 7 2.5 6 2 3 5 2 2 528 23 142,418 2.9 7 2.4 6 2 3 5 2 2 524 19 147,772 2.8 7 2.4 6 2 2 5 2.1 525 19 153,929 2.7 6 2.3 5 2.1 5 2 0 523 17 158,275 2.6 6 2.2 5 2.1 5 2 0 526 19 160,086 2.6 6 2.2 5 2.1 5 2 0 524 17 165,157 2.5 6 2.1 5 2 0 5 1 9 427 19 166,243 2.5 6 2.1 5 2 0 5 1 9 425 17 172,038 2.4 6 2.0 5 1 9 4 1 8 428 19 172,400 2.4 6 2.0 5 1 9 4 1 8 426 17 178,920 2.3 5 1.9 4 1 8 4 1 8 427 17 185,801 2.3 5 1.9 4 1 8 4 1.7 428 17 192,683 2.2 5 1.8 4 1.7 4 1 6 4


20" Row Spacing


401-312B 12/02/2009










17 28 71,027 2 9 7 2.5 6 2.3 5 2.2 517 27 73,658 2 8 7 2.4 6 2.2 5 2.1 517 26 76,491 2.7 6 2.3 5 2.2 5 2.1 519 28 79,383 2 6 6 2.2 5 2.1 5 2.0 517 25 79,551 2 6 6 2.2 5 2.1 5 2.0 519 27 82,324 2 5 6 2.1 5 2.0 5 1.9 417 24 82,865 2 5 6 2.1 5 2.0 5 1.9 419 26 85,490 2.4 6 2.0 5 1.9 4 1.8 417 23 86,468 2.4 6 2.0 5 1.9 4 1.8 419 25 88,909 2.4 6 2.0 5 1.9 4 1.8 419 24 92,614 2 3 5 1.9 4 1.8 4 1.7 423 28 96,096 2 2 5 1.8 4 1.7 4 1.6 419 23 96,641 2 2 5 1.8 4 1.7 4 1.6 423 27 99,655 2.1 5 1.7 4 1.7 4 1.6 424 28 100,274 2.1 5 1.7 4 1.6 4 1.6 323 26 103,488 2 0 5 1.7 4 1.6 4 1.5 324 27 103,988 2 0 5 1.7 4 1.6 4 1.5 325 28 104,452 2 0 5 1.7 4 1.6 4 1.5 317 19 104,672 2 0 5 1.7 4 1.6 4 1.5 323 25 107,627 1 9 4 1.6 4 1.5 3 1.5 324 26 107,987 1 9 4 1.6 4 1.5 3 1.5 325 27 108,320 1 9 4 1.6 4 1.5 3 1.4 326 28 108,630 1 9 4 1.6 4 1.5 3 1.4 323 24 112,112 1 9 4 1.6 3 1.5 3 1.4 324 25 112,307 1 9 4 1.6 3 1.5 3 1.4 325 26 112,487 1 9 4 1.5 3 1.5 3 1.4 326 27 112,653 1 9 4 1.5 3 1.5 3 1.4 327 28 112,808 1 9 4 1.5 3 1.5 3 1.4 323 23 116,986 1 8 4 1.5 3 1.4 3 1.3 328 27 121,319 1.7 4 1.4 3 1.4 3 1.3 327 26 121,486 1.7 4 1.4 3 1.4 3 1.3 326 25 121,665 1.7 4 1.4 3 1.4 3 1.3 325 24 121,860 1.7 4 1.4 3 1.4 3 1.3 324 23 122,072 1.7 4 1.4 3 1.4 3 1.3 328 26 125,985 1.7 4 1.4 3 1.3 3 1.2 327 25 126,345 1.7 4 1.4 3 1.3 3 1.2 326 24 126,735 1 6 4 1.4 3 1.3 3 1.2 325 23 127,159 1 6 4 1.4 3 1.3 3 1.2 319 17 130,749 1 6 4 1.3 3 1.3 3 1.2 328 25 131,024 1 6 4 1.3 3 1.3 3 1.2 327 24 131,609 1 6 4 1.3 3 1.3 3 1.2 326 23 132,245 1 6 4 1.3 3 1.2 3 1.2 328 24 136,484 1 5 3 1.3 3 1.2 3 1.1 227 23 137,331 1 5 3 1.3 3 1.2 3 1.1 223 19 141,615 1 5 3 1.2 3 1.2 2 1.1 228 23 142,418 1 5 3 1.2 3 1.2 2 1.1 224 19 147,772 1.4 3 1.2 3 1.1 2 1.1 225 19 153,929 1.4 3 1.1 2 1.1 2 1.0 223 17 158,275 1 3 3 1.1 2 1.0 2 1.0 226 19 160,086 1 3 3 1.1 2 1.0 2 1.0 224 17 165,157 1 3 3 1.1 2 1.0 2 0.9 227 19 166,243 1 3 3 1.0 2 1.0 2 0.9 225 17 172,038 1 2 3 1.0 2 1.0 2 0.9 228 19 172,400 1 2 3 1.0 2 1.0 2 0.9 226 17 178,920 1 2 2 1.0 2 0.9 2 0.9 227 17 185,801 1.1 2 0.9 2 0.9 2 0.8 228 17 192,683 1.1 2 0.9 2 0.9 2 0.8 2

Upper Drive

Range Sprockets:




12/02/2009 401-312B










17 28 142,054 2.9 8 2.5 8 2 3 8 2 2 817 27 147,316 2.8 8 2.4 8 2 2 8 2.1 817 26 152,982 2.7 8 2.3 8 2 2 8 2.1 819 28 158,767 2.6 8 2.2 8 2.1 8 2 0 817 25 159,101 2.6 8 2.2 8 2.1 8 2 0 819 27 164,647 2.5 8 2.1 8 2 0 8 1 9 817 24 165,730 2.5 8 2.1 8 2 0 8 1 9 819 26 170,980 2.4 8 2.0 8 1 9 8 1 8 817 23 172,936 2.4 8 2.0 8 1 9 8 1 8 819 25 177,819 2.4 8 2.0 8 1 9 8 1 8 819 24 185,228 2.3 8 1.9 8 1 8 8 1.7 823 28 192,191 2.2 8 1.8 8 1.7 8 1 6 819 23 193,281 2.2 8 1.8 8 1.7 8 1 6 823 27 199,310 2.1 8 1.7 8 1.7 8 1 6 824 28 200,548 2.1 8 1.7 8 1 6 8 1 6 723 26 206,975 2.0 8 1.7 8 1 6 8 1 5 724 27 207,975 2.0 8 1.7 8 1 6 8 1 5 725 28 208,904 2.0 8 1.7 8 1 6 8 1 5 717 19 209,343 2.0 8 1.7 8 1 6 8 1 5 723 25 215,254 1.9 8 1.6 8 1 5 7 1 5 724 26 215,974 1.9 8 1.6 8 1 5 7 1 5 725 27 216,641 1.9 8 1.6 8 1 5 7 1.4 726 28 217,260 1.9 8 1.6 8 1 5 7 1.4 723 24 224,223 1.9 8 1.6 7 1 5 7 1.4 724 25 224,613 1.9 8 1.6 7 1 5 7 1.4 725 26 224,973 1.9 8 1.5 7 1 5 7 1.4 726 27 225,306 1.9 8 1.5 7 1 5 7 1.4 727 28 225,616 1.9 8 1.5 7 1 5 7 1.4 723 23 233,972 1.8 8 1.5 7 1.4 7 1 3 628 27 242,638 1.7 8 1.4 7 1.4 6 1 3 627 26 242,971 1.7 8 1.4 7 1.4 6 1 3 626 25 243,331 1.7 8 1.4 7 1.4 6 1 3 625 24 243,721 1.7 8 1.4 7 1.4 6 1 3 624 23 244,145 1.7 8 1.4 7 1.4 6 1 3 628 26 251,970 1.7 8 1.4 7 1 3 6 1 2 627 25 252,690 1.7 8 1.4 7 1 3 6 1 2 626 24 253,470 1.6 8 1.4 7 1 3 6 1 2 625 23 254,317 1.6 8 1.4 7 1 3 6 1 2 619 17 261,498 1.6 8 1.3 6 1 3 6 1 2 628 25 262,049 1.6 8 1.3 6 1 3 6 1 2 627 24 263,219 1.6 8 1.3 6 1 3 6 1 2 626 23 264,490 1.6 8 1.3 6 1 2 6 1 2 628 24 272,967 1.5 7 1.3 6 1 2 6 1.1 527 23 274,663 1.5 7 1.3 6 1 2 6 1.1 523 19 283,229 1.5 7 1.2 6 1 2 5 1.1 528 23 284,836 1.5 7 1.2 6 1 2 5 1.1 524 19 295,544 1.4 7 1.2 6 1.1 5 1.1 525 19 307,858 1.4 6 1.1 5 1.1 5 1 0 523 17 316,550 1.3 6 1.1 5 1 0 5 1 0 526 19 320,172 1.3 6 1.1 5 1 0 5 1 0 524 17 330,314 1.3 6 1.1 5 1 0 5 0 9 427 19 332,487 1.3 6 1.0 5 1 0 5 0 9 425 17 344,077 1.2 6 1.0 5 1 0 4 0 9 428 19 344,801 1.2 6 1.0 5 1 0 4 0 9 426 17 357,840 1.2 5 1.0 4 0 9 4 0 9 427 17 371,603 1.1 5 0.9 4 0 9 4 0 8 428 17 385,366 1.1 5 0.9 4 0 9 4 0 8 4



401-312B 12/02/2009










17 28 142,054 1 5 7 1.2 6 1.2 5 1.1 517 27 147,316 1.4 7 1.2 6 1.1 5 1.1 517 26 152,982 1.4 6 1.1 5 1.1 5 1.0 519 28 158,767 1 3 6 1.1 5 1.0 5 1.0 517 25 159,101 1 3 6 1.1 5 1.0 5 1.0 519 27 164,647 1 3 6 1.1 5 1.0 5 1.0 417 24 165,730 1 3 6 1.1 5 1.0 5 0.9 419 26 170,980 1 2 6 1.0 5 1.0 4 0.9 417 23 172,936 1 2 6 1.0 5 1.0 4 0.9 419 25 177,819 1 2 6 1.0 5 0.9 4 0.9 419 24 185,228 1.1 5 0.9 4 0.9 4 0.8 423 28 192,191 1.1 5 0.9 4 0.9 4 0.8 419 23 193,281 1.1 5 0.9 4 0.9 4 0.8 423 27 199,310 1 0 5 0.9 4 0.8 4 0.8 424 28 200,548 1 0 5 0.9 4 0.8 4 0.8 323 26 206,975 1 0 5 0.8 4 0.8 4 0.8 324 27 207,975 1 0 5 0.8 4 0.8 4 0.8 325 28 208,904 1 0 5 0.8 4 0.8 4 0.8 317 19 209,343 1 0 5 0.8 4 0.8 4 0.7 323 25 215,254 1 0 4 0.8 4 0.8 3 0.7 324 26 215,974 1 0 4 0.8 4 0.8 3 0.7 325 27 216,641 1 0 4 0.8 4 0.8 3 0.7 326 28 217,260 1 0 4 0.8 4 0.8 3 0.7 323 24 224,223 0 9 4 0.8 3 0.7 3 0.7 324 25 224,613 0 9 4 0.8 3 0.7 3 0.7 325 26 224,973 0 9 4 0.8 3 0.7 3 0.7 326 27 225,306 0 9 4 0.8 3 0.7 3 0.7 327 28 225,616 0 9 4 0.8 3 0.7 3 0.7 323 23 233,972 0 9 4 0.7 3 0.7 3 0.7 328 27 242,638 0 9 4 0.7 3 0.7 3 0.6 327 26 242,971 0 9 4 0.7 3 0.7 3 0.6 326 25 243,331 0 9 4 0.7 3 0.7 3 0.6 325 24 243,721 0 9 4 0.7 3 0.7 3 0.6 324 23 244,145 0 9 4 0.7 3 0.7 3 0.6 328 26 251,970 0 8 4 0.7 3 0.7 3 0.6 327 25 252,690 0 8 4 0.7 3 0.7 3 0.6 326 24 253,470 0 8 4 0.7 3 0.7 3 0.6 325 23 254,317 0 8 4 0.7 3 0.6 3 0.6 319 17 261,498 0 8 4 0.7 3 0.6 3 0.6 328 25 262,049 0 8 4 0.7 3 0.6 3 0.6 327 24 263,219 0 8 4 0.7 3 0.6 3 0.6 326 23 264,490 0 8 4 0.7 3 0.6 3 0.6 328 24 272,967 0 8 3 0.6 3 0.6 3 0.6 227 23 274,663 0 8 3 0.6 3 0.6 3 0.6 223 19 283,229 0.7 3 0.6 3 0.6 2 0.6 228 23 284,836 0.7 3 0.6 3 0.6 2 0.6 224 19 295,544 0.7 3 0.6 3 0.6 2 0.5 225 19 307,858 0.7 3 0.6 2 0.5 2 0.5 223 17 316,550 0.7 3 0.6 2 0.5 2 0.5 226 19 320,172 0.7 3 0.5 2 0.5 2 0.5 224 17 330,314 0 6 3 0.5 2 0.5 2 0.5 227 19 332,487 0 6 3 0.5 2 0.5 2 0.5 225 17 344,077 0 6 3 0.5 2 0.5 2 0.5 228 19 344,801 0 6 3 0.5 2 0.5 2 0.5 226 17 357,840 0 6 2 0.5 2 0.5 2 0.4 227 17 371,603 0 6 2 0.5 2 0.4 2 0.4 228 17 385,366 0 5 2 0.5 2 0.4 2 0.4 2

36" Row Spacing


Upper Drive

Range Sprockets:


30" Row Spacing

12/02/2009 401-312B


Soybeans (100 Cell Meter) (page 1 of 2)

3PT YIELD PRO 1225 - 1625 SOYBEAN Page 1 of 2403-122D 1700-2200 seeds/pound Singulating

100 Cell WheelTALC REQUIRED






17 28 99,964 4.2 8 3.5 8 3 3 8 3.1 817 27 103,667 4.0 8 3.4 8 3 2 8 3 0 817 26 107,654 3.9 8 3.2 8 3.1 8 2 9 819 28 111,725 3.7 8 3.1 8 3 0 8 2 8 817 25 111,960 3.7 8 3.1 8 2 9 8 2 8 819 27 115,863 3.6 8 3.0 8 2 8 8 2.7 817 24 116,625 3.6 8 3.0 8 2 8 8 2.7 819 26 120,319 3.5 8 2.9 8 2.7 8 2 6 817 23 121,696 3.4 8 2.9 8 2.7 8 2 6 819 25 125,132 3.3 8 2.8 8 2 6 8 2 5 719 24 130,346 3.2 8 2.7 8 2 5 7 2.4 723 28 135,246 3.1 8 2.6 8 2.4 7 2 3 719 23 136,013 3.1 8 2.6 7 2.4 7 2 3 723 27 140,255 3.0 8 2.5 7 2.4 7 2 2 624 28 141,126 3.0 8 2.5 7 2 3 7 2 2 623 26 145,649 2.9 8 2.4 7 2 3 7 2 2 624 27 146,353 2.9 8 2.4 7 2 3 7 2.1 625 28 147,006 2.8 8 2.4 7 2 2 6 2.1 617 19 147,316 2.8 8 2.4 7 2 2 6 2.1 623 25 151,475 2.8 8 2.3 7 2 2 6 2.1 624 26 151,982 2.8 8 2.3 7 2 2 6 2.1 625 27 152,451 2.7 8 2.3 7 2 2 6 2.1 626 28 152,887 2.7 8 2.3 7 2 2 6 2.1 623 24 157,787 2.7 8 2.2 6 2.1 6 2 0 624 25 158,061 2.6 8 2.2 6 2.1 6 2 0 625 26 158,314 2.6 8 2.2 6 2.1 6 2 0 626 27 158,549 2.6 8 2.2 6 2.1 6 2 0 627 28 158,767 2.6 8 2.2 6 2.1 6 2 0 623 23 164,647 2.5 7 2.1 6 2 0 6 1 9 528 27 170,745 2.4 7 2.0 6 1 9 6 1 8 527 26 170,980 2.4 7 2.0 6 1 9 6 1 8 526 25 171,233 2.4 7 2.0 6 1 9 5 1 8 525 24 171,507 2.4 7 2.0 6 1 9 5 1 8 524 23 171,806 2.4 7 2.0 6 1 9 5 1 8 528 26 177,312 2.4 7 2.0 6 1 9 5 1 8 527 25 177,819 2.4 7 2.0 6 1 9 5 1 8 526 24 178,368 2.3 7 2.0 6 1 9 5 1 8 525 23 178,964 2.3 7 1.9 6 1 8 5 1 8 519 17 184,017 2.3 7 1.9 5 1 8 5 1.7 528 25 184,405 2.3 7 1.9 5 1 8 5 1.7 527 24 185,228 2.3 7 1.9 5 1 8 5 1.7 526 23 186,123 2.2 6 1.9 5 1 8 5 1.7 528 24 192,088 2.2 6 1.8 5 1.7 5 1 6 527 23 193,281 2.2 6 1.8 5 1.7 5 1 6 523 19 199,310 2.1 6 1.7 5 1.7 5 1 6 428 23 200,440 2.1 6 1.7 5 1 6 5 1 6 424 19 207,975 2.0 6 1.7 5 1 6 4 1 5 425 19 216,641 1.9 6 1.6 5 1 5 4 1.4 423 17 222,758 1.9 5 1.6 4 1 5 4 1.4 426 19 225,306 1.9 5 1.5 4 1 5 4 1.4 424 17 232,443 1.8 5 1.5 4 1.4 4 1 3 427 19 233,972 1.8 5 1.5 4 1.4 4 1 3 425 17 242,128 1.7 5 1.4 4 1.4 4 1 3 428 19 242,638 1.7 5 1.4 4 1.4 4 1 3 426 17 251,813 1.7 5 1.4 4 1 3 4 1 2 327 17 261,498 1.6 4 1.3 4 1 3 3 1 2 328 17 271,183 1.5 4 1.3 3 1 2 3 1 2 3


20" Row Spacing


401-312B 12/02/2009



3PT YIELD PRO 1225 - 1625 SOYBEAN Page 2 of 2403-122D 1700-2200 seeds/pound Singulating

100 Cell WheelTALC REQUIRED






17 28 99,964 2.1 6 1.7 5 1.7 5 1.6 417 27 103,667 2 0 6 1.7 5 1.6 4 1.5 417 26 107,654 1 9 6 1.6 5 1.5 4 1.5 419 28 111,725 1 9 5 1.6 4 1.5 4 1.4 417 25 111,960 1 9 5 1.6 4 1.5 4 1.4 419 27 115,863 1 8 5 1.5 4 1.4 4 1.4 417 24 116,625 1 8 5 1.5 4 1.4 4 1.3 419 26 120,319 1.7 5 1.4 4 1.4 4 1.3 417 23 121,696 1.7 5 1.4 4 1.4 4 1.3 419 25 125,132 1.7 5 1.4 4 1.3 4 1.3 319 24 130,346 1 6 4 1.3 4 1.3 3 1.2 323 28 135,246 1 5 4 1.3 4 1.2 3 1.2 319 23 136,013 1 5 4 1.3 3 1.2 3 1.2 323 27 140,255 1 5 4 1.2 3 1.2 3 1.1 324 28 141,126 1 5 4 1.2 3 1.2 3 1.1 323 26 145,649 1.4 4 1.2 3 1.1 3 1.1 324 27 146,353 1.4 4 1.2 3 1.1 3 1.1 325 28 147,006 1.4 4 1.2 3 1.1 3 1.1 317 19 147,316 1.4 4 1.2 3 1.1 3 1.1 323 25 151,475 1.4 4 1.2 3 1.1 3 1.0 324 26 151,982 1.4 4 1.1 3 1.1 3 1.0 325 27 152,451 1.4 4 1.1 3 1.1 3 1.0 326 28 152,887 1.4 4 1.1 3 1.1 3 1.0 323 24 157,787 1 3 4 1.1 3 1.0 3 1.0 324 25 158,061 1 3 4 1.1 3 1.0 3 1.0 325 26 158,314 1 3 4 1.1 3 1.0 3 1.0 326 27 158,549 1 3 4 1.1 3 1.0 3 1.0 327 28 158,767 1 3 4 1.1 3 1.0 3 1.0 323 23 164,647 1 3 3 1.1 3 1.0 3 1.0 228 27 170,745 1 2 3 1.0 3 1.0 3 0.9 227 26 170,980 1 2 3 1.0 3 1.0 3 0.9 226 25 171,233 1 2 3 1.0 3 1.0 2 0.9 225 24 171,507 1 2 3 1.0 3 1.0 2 0.9 224 23 171,806 1 2 3 1.0 3 1.0 2 0.9 228 26 177,312 1 2 3 1.0 3 0.9 2 0.9 227 25 177,819 1 2 3 1.0 3 0.9 2 0.9 226 24 178,368 1 2 3 1.0 3 0.9 2 0.9 225 23 178,964 1 2 3 1.0 3 0.9 2 0.9 219 17 184,017 1.1 3 0.9 2 0.9 2 0.9 228 25 184,405 1.1 3 0.9 2 0.9 2 0.9 227 24 185,228 1.1 3 0.9 2 0.9 2 0.8 226 23 186,123 1.1 3 0.9 2 0.9 2 0.8 228 24 192,088 1.1 3 0.9 2 0.9 2 0.8 227 23 193,281 1.1 3 0.9 2 0.9 2 0.8 223 19 199,310 1 0 3 0.9 2 0.8 2 0.8 228 23 200,440 1 0 3 0.9 2 0.8 2 0.8 224 19 207,975 1 0 3 0.8 2 0.8 2 0.8 225 19 216,641 1 0 3 0.8 2 0.8 2 0.7 223 17 222,758 0 9 2 0.8 2 0.7 2 0.7 226 19 225,306 0 9 2 0.8 2 0.7 2 0.7 224 17 232,443 0 9 2 0.7 2 0.7 2 0.7 227 19 233,972 0 9 2 0.7 2 0.7 2 0.7 225 17 242,128 0 9 2 0.7 2 0.7 2 0.6 228 19 242,638 0 9 2 0.7 2 0.7 2 0.6 226 17 251,813 0 8 2 0.7 2 0.7 2 0.6 127 17 261,498 0 8 2 0.7 2 0.6 1 0.6 128 17 271,183 0 8 2 0.6 1 0.6 1 0.6 1

Upper Drive

Range Sprockets:




12/02/2009 401-312B



3PT YIELD PRO 1225 - 1625 SOYBEAN Page 1 of 2403-123D 2200-2700 seeds/pound Singulating403-124D 2700-3200 seeds/pound 110 Cell Wheel403-125D 3100-3800 seeds/pound TALC REQUIRED403-126D 3600-4000 seeds/pound






17 28 109,961 3.8 8 3.2 8 3 0 8 2 9 817 27 114,033 3.7 8 3.1 8 2 9 8 2 8 817 26 118,419 3.5 8 2.9 8 2 8 8 2 6 819 28 122,897 3.4 8 2.8 8 2.7 8 2 6 817 25 123,156 3.4 8 2.8 8 2.7 8 2 5 819 27 127,449 3.3 8 2.7 8 2 6 8 2 5 817 24 128,287 3.3 8 2.7 8 2 6 8 2.4 819 26 132,351 3.2 8 2.6 8 2 5 8 2.4 817 23 133,865 3.1 8 2.6 8 2 5 8 2 3 819 25 137,645 3.0 8 2.5 8 2.4 8 2 3 819 24 143,380 2.9 8 2.4 8 2 3 8 2 2 823 28 148,770 2.8 8 2.3 8 2 2 8 2.1 819 23 149,614 2.8 8 2.3 8 2 2 8 2.1 823 27 154,280 2.7 8 2.3 8 2.1 8 2 0 724 28 155,239 2.7 8 2.2 8 2.1 8 2 0 723 26 160,214 2.6 8 2.2 8 2.1 7 2 0 724 27 160,988 2.6 8 2.2 8 2.1 7 1 9 725 28 161,707 2.6 8 2.2 8 2 0 7 1 9 717 19 162,047 2.6 8 2.2 8 2 0 7 1 9 723 25 166,623 2.5 8 2.1 8 2 0 7 1 9 724 26 167,180 2.5 8 2.1 7 2 0 7 1 9 725 27 167,696 2.5 8 2.1 7 2 0 7 1 9 726 28 168,175 2.5 8 2.1 7 2 0 7 1 9 723 24 173,565 2.4 8 2.0 7 1 9 7 1 8 624 25 173,867 2.4 8 2.0 7 1 9 7 1 8 625 26 174,146 2.4 8 2.0 7 1 9 7 1 8 626 27 174,404 2.4 8 2.0 7 1 9 7 1 8 627 28 174,643 2.4 8 2.0 7 1 9 7 1 8 623 23 181,112 2.3 8 1.9 7 1 8 6 1.7 628 27 187,820 2.2 8 1.9 7 1 8 6 1.7 627 26 188,078 2.2 8 1.9 7 1 8 6 1.7 626 25 188,356 2.2 8 1.9 7 1 8 6 1.7 625 24 188,658 2.2 8 1.8 7 1.7 6 1.7 624 23 188,986 2.2 8 1.8 7 1.7 6 1.7 628 26 195,043 2.1 8 1.8 6 1.7 6 1 6 627 25 195,601 2.1 8 1.8 6 1.7 6 1 6 626 24 196,204 2.1 8 1.8 6 1.7 6 1 6 625 23 196,861 2.1 8 1.8 6 1.7 6 1 6 619 17 202,419 2.1 7 1.7 6 1 6 6 1 5 528 25 202,845 2.1 7 1.7 6 1 6 6 1 5 527 24 203,751 2.1 7 1.7 6 1 6 6 1 5 526 23 204,735 2.0 7 1.7 6 1 6 6 1 5 528 24 211,297 2.0 7 1.6 6 1 6 5 1 5 527 23 212,609 2.0 7 1.6 6 1 6 5 1 5 523 19 219,241 1.9 7 1.6 6 1 5 5 1.4 528 23 220,484 1.9 7 1.6 6 1 5 5 1.4 524 19 228,773 1.8 6 1.5 5 1.4 5 1.4 525 19 238,305 1.8 6 1.5 5 1.4 5 1 3 523 17 245,034 1.7 6 1.4 5 1 3 5 1 3 426 19 247,837 1.7 6 1.4 5 1 3 5 1 3 424 17 255,687 1.6 6 1.4 5 1 3 4 1 2 427 19 257,369 1.6 6 1.4 5 1 3 4 1 2 425 17 266,341 1.6 6 1.3 5 1 2 4 1 2 428 19 266,901 1.6 5 1.3 4 1 2 4 1 2 426 17 276,994 1.5 5 1.3 4 1 2 4 1.1 427 17 287,648 1.5 5 1.2 4 1.1 4 1.1 428 17 298,302 1.4 5 1.2 4 1.1 4 1.1 4



401-312B 12/02/2009



3PT YIELD PRO 1225 - 1625 SOYBEAN Page 2 of 2403-123D 2200-2700 seeds/pound Singulating403-124D 2700-3200 seeds/pound 110 Cell Wheel403-125D 3100-3800 seeds/pound TALC REQUIRED403-126D 3600-4000 seeds/pound






17 28 109,961 1 9 7 1.6 6 1.5 5 1.4 517 27 114,033 1 8 7 1.5 5 1.4 5 1.4 517 26 118,419 1 8 6 1.5 5 1.4 5 1.3 519 28 122,897 1.7 6 1.4 5 1.3 5 1.3 417 25 123,156 1.7 6 1.4 5 1.3 5 1.3 419 27 127,449 1 6 6 1.4 5 1.3 4 1.2 417 24 128,287 1 6 6 1.4 5 1.3 4 1.2 419 26 132,351 1 6 6 1.3 5 1.2 4 1.2 417 23 133,865 1 6 5 1.3 4 1.2 4 1.2 419 25 137,645 1 5 5 1.3 4 1.2 4 1.1 419 24 143,380 1 5 5 1.2 4 1.2 4 1.1 423 28 148,770 1.4 5 1.2 4 1.1 4 1.1 419 23 149,614 1.4 5 1.2 4 1.1 4 1.0 423 27 154,280 1.4 5 1.1 4 1.1 4 1.0 324 28 155,239 1 3 5 1.1 4 1.1 4 1.0 323 26 160,214 1 3 4 1.1 4 1.0 3 1.0 324 27 160,988 1 3 4 1.1 4 1.0 3 1.0 325 28 161,707 1 3 4 1.1 4 1.0 3 1.0 317 19 162,047 1 3 4 1.1 4 1.0 3 1.0 323 25 166,623 1 3 4 1.0 4 1.0 3 0.9 324 26 167,180 1 3 4 1.0 3 1.0 3 0.9 325 27 167,696 1 2 4 1.0 3 1.0 3 0.9 326 28 168,175 1 2 4 1.0 3 1.0 3 0.9 323 24 173,565 1 2 4 1.0 3 1.0 3 0.9 324 25 173,867 1 2 4 1.0 3 0.9 3 0.9 325 26 174,146 1 2 4 1.0 3 0.9 3 0.9 326 27 174,404 1 2 4 1.0 3 0.9 3 0.9 327 28 174,643 1 2 4 1.0 3 0.9 3 0.9 323 23 181,112 1 2 4 1.0 3 0.9 3 0.9 328 27 187,820 1.1 4 0.9 3 0.9 3 0.8 327 26 188,078 1.1 4 0.9 3 0.9 3 0.8 326 25 188,356 1.1 4 0.9 3 0.9 3 0.8 325 24 188,658 1.1 4 0.9 3 0.9 3 0.8 324 23 188,986 1.1 4 0.9 3 0.9 3 0.8 328 26 195,043 1.1 4 0.9 3 0.8 3 0.8 327 25 195,601 1.1 4 0.9 3 0.8 3 0.8 326 24 196,204 1.1 4 0.9 3 0.8 3 0.8 325 23 196,861 1.1 4 0.9 3 0.8 3 0.8 319 17 202,419 1 0 3 0.9 3 0.8 3 0.8 228 25 202,845 1 0 3 0.9 3 0.8 3 0.8 227 24 203,751 1 0 3 0.9 3 0.8 3 0.8 226 23 204,735 1 0 3 0.9 3 0.8 3 0.8 228 24 211,297 1 0 3 0.8 3 0.8 2 0.7 227 23 212,609 1 0 3 0.8 3 0.8 2 0.7 223 19 219,241 1 0 3 0.8 3 0.8 2 0.7 228 23 220,484 0 9 3 0.8 3 0.7 2 0.7 224 19 228,773 0 9 3 0.8 2 0.7 2 0.7 225 19 238,305 0 9 3 0.7 2 0.7 2 0.7 223 17 245,034 0 9 3 0.7 2 0.7 2 0.6 226 19 247,837 0 8 3 0.7 2 0.7 2 0.6 224 17 255,687 0 8 3 0.7 2 0.6 2 0.6 227 19 257,369 0 8 3 0.7 2 0.6 2 0.6 225 17 266,341 0 8 3 0.7 2 0.6 2 0.6 228 19 266,901 0 8 2 0.7 2 0.6 2 0.6 226 17 276,994 0 8 2 0.6 2 0.6 2 0.6 227 17 287,648 0.7 2 0.6 2 0.6 2 0.5 228 17 298,302 0.7 2 0.6 2 0.6 2 0.5 2

36" Row Spacing


Upper Drive

Range Sprockets:


30" Row Spacing

12/02/2009 401-312B


Volumetric Meter Planting

Volumetric meter planting rate is determined by:

• crop and seed variant

• meter wheel selection, and

• meter drive configuration

There are no other adjustments.

Reading a Volumetric Rate ChartHydraulic or Ground Drive1. Consult the chart for your crop and meter wheel.

2. Note any seed lubricant required. See “Seed Lubricants” on page 67 for seed lubricant information.

3. Find the columns for your row spacing.

4. Find the desired seed rate (which is pounds peracre for volumetric seeds).

5. Note the maximum ground speed for that rate.

With hydraulic meter drive, enter the rate in the seedmonitor. With ground drive, configure the sprockets.

Ground Drive

6. The Range and Upper Drive sprockets are at thetop of the columns for the row spacing.

7. The Transmission sprockets are in the table rows,found to the left of the Seed Rate.

3PT YIELD PRO 1225 - 1625 WHE403-118D Wheat Narrow Volum

64 lb. bu. HARD RED WINTE TALC RE

R S k t

15 Row Spac ngTwin Row 30"

1625 WHEATVolumetric

64 lb. bu. HARD RED WINTER Wheat. No Seed TreatmentTALC REQUIRED

o64 lb. bu. HARD RED WINTER Wheat No Seed Treatment

TALC REQUIRED

R S k t

15" Row SpacingTwin Row 30" Twin Ro

15" Row SR S

nations Seed Planting Seed PRate Speed Rate

Driven (pounds/acre) (mph) (pounds/acre)

28 23 8 3627 23 8 3726 24 8 39

ission Maximum Maations Seed Planting Seed P

Rate Speed Rate SDriven (pounds/acre) (mph) (pounds/acre) (

28 23 8 3627 23 8 37

Range Sprockets:Driver = 15Driven = 30

Sprocket: 18

Transmission MaximumCombinations Seed Planting

Rate SpeedDriver Driven (pounds/acre) (mph) (pou

17 28 23 817 27 23 817 26 24 819 28 25 8

15" Row Spacing

Upper Drive

401-312B 12/02/2009


Wheat, 64lb/bu Hard, Narrow Wheel3PT YIELD PRO 1225 - 1625 WHEAT403-118D Wheat Narrow Volumetric


Range Sprockets:Driver = 15 Driver = 30Driven = 30 Driven = 38

Sprocket: 18 Sprocket: 18

Transmission Maximum MaximumCombinations Seed Planting Seed Planting

Rate Speed Rate SpeedDriver Driven (pounds/acre) (mph) (pounds/acre) (mph)

17 28 23 8 36 817 27 23 8 37 817 26 24 8 39 819 28 25 8 40 817 25 25 8 40 819 27 26 8 41 817 24 26 8 42 819 26 27 8 43 817 23 28 8 44 819 25 28 8 45 819 24 30 8 47 823 28 31 8 48 819 23 31 8 49 823 27 32 8 50 824 28 32 8 51 823 26 33 8 52 824 27 33 8 52 825 28 33 8 53 817 19 33 8 53 823 25 34 8 54 824 26 34 8 54 825 27 35 8 55 826 28 35 8 55 823 24 36 8 56 824 25 36 8 57 825 26 36 8 57 826 27 36 8 57 827 28 36 8 57 823 23 37 8 59 828 27 39 8 61 827 26 39 8 61 826 25 39 8 61 825 24 39 8 61 824 23 39 8 61 828 26 40 8 63 727 25 40 8 64 726 24 40 8 64 725 23 41 8 64 719 17 42 8 66 728 25 42 8 66 727 24 42 8 66 726 23 42 8 67 728 24 44 8 69 727 23 44 8 69 723 19 45 8 71 628 23 45 8 72 624 19 47 8 74 625 19 49 8 78 623 17 50 8 80 626 19 51 8 81 624 17 53 8 83 527 19 53 8 84 525 17 55 8 87 528 19 55 8 87 526 17 57 8 90 527 17 59 8 94 528 17 61 8 97 5

15" Row SpacingTwin Row 30" Twin Row 30"



Pounds permeter revolution0.034(for hydraulic drive setup)

12/02/2009 401-312B


Wheat, 64lb/bu Hard, Wide Wheel3PT YIELD PRO 1225 - 1625 WHEAT403-119D Wheat Wide Volumetric






17 28 52 8 82 817 27 54 8 85 817 26 56 8 88 819 28 58 8 92 817 25 58 8 92 819 27 60 8 95 817 24 61 8 96 819 26 63 8 99 817 23 63 8 100 819 25 65 8 103 819 24 68 8 107 823 28 70 8 111 819 23 71 8 112 823 27 73 8 115 824 28 73 8 116 823 26 76 8 120 824 27 76 8 120 825 28 76 8 121 817 19 77 8 121 823 25 79 8 124 824 26 79 8 125 825 27 79 8 125 826 28 80 8 126 823 24 82 8 130 824 25 82 8 130 825 26 82 8 130 826 27 82 8 130 827 28 83 8 130 823 23 86 8 135 828 27 89 8 140 827 26 89 8 140 826 25 89 8 141 825 24 89 8 141 824 23 89 8 141 828 26 92 8 146 727 25 92 8 146 726 24 93 8 146 725 23 93 8 147 719 17 96 8 151 728 25 96 8 151 727 24 96 8 152 726 23 97 8 153 728 24 100 8 158 727 23 101 8 159 723 19 104 8 164 628 23 104 8 165 624 19 108 8 171 625 19 113 8 178 623 17 116 8 183 626 19 117 8 185 624 17 121 8 191 527 19 122 8 192 525 17 126 8 199 528 19 126 8 199 526 17 131 8 207 527 17 136 8 215 528 17 141 8 223 5





401-312B 12/02/2009


Wheat, 62lb/bu Soft, Wide Wheel3PT YIELD PRO 1225 - 1625 WHEAT403-119D Wheat Wide Volumetric

62 lb. bu. SOFT RED WINTER Wheat. W / Seed TreatmentTALC REQUIRED





17 28 45 8 72 817 27 47 8 74 817 26 49 8 77 819 28 51 8 80 817 25 51 8 80 819 27 53 8 83 817 24 53 8 83 819 26 55 8 86 817 23 55 8 87 819 25 57 8 90 819 24 59 8 93 823 28 61 8 97 819 23 62 8 97 823 27 64 8 100 824 28 64 8 101 823 26 66 8 104 824 27 66 8 105 825 28 67 8 105 817 19 67 8 105 823 25 69 8 108 824 26 69 8 109 825 27 69 8 109 826 28 69 8 109 823 24 72 8 113 824 25 72 8 113 825 26 72 8 113 826 27 72 8 113 827 28 72 8 114 823 23 75 8 118 828 27 77 8 122 827 26 78 8 122 826 25 78 8 123 825 24 78 8 123 824 23 78 8 123 828 26 80 8 127 727 25 81 8 127 726 24 81 8 128 725 23 81 8 128 719 17 83 8 132 728 25 84 8 132 727 24 84 8 133 726 23 84 8 133 728 24 87 8 137 727 23 88 8 138 723 19 90 8 143 628 23 91 8 143 624 19 94 8 149 625 19 98 8 155 623 17 101 8 159 626 19 102 8 161 624 17 105 8 166 527 19 106 8 167 525 17 110 8 173 528 19 110 8 174 526 17 114 8 180 527 17 119 8 187 528 17 123 8 194 5





12/02/2009 401-312B


Wheat, 62lb/bu Soft, V3 Wheel3PT YIELD PRO 1225 - 1625 WHEAT403-120D V3 Volumetric

62 lb. bu. SOFT RED WINTER Wheat. W / Seed TreatmentTALC REQUIRED





17 28 60 8 95 817 27 63 8 99 817 26 65 8 103 819 28 67 8 107 817 25 68 8 107 819 27 70 8 110 817 24 70 8 111 819 26 73 8 115 817 23 74 8 116 819 25 76 8 119 819 24 79 8 124 823 28 82 8 129 819 23 82 8 130 823 27 85 8 134 824 28 85 8 135 723 26 88 8 139 724 27 88 8 140 725 28 89 8 140 717 19 89 8 140 723 25 91 8 144 724 26 92 8 145 725 27 92 8 145 726 28 92 8 146 723 24 95 8 150 724 25 95 8 151 725 26 96 8 151 726 27 96 8 151 727 28 96 8 151 723 23 99 8 157 628 27 103 8 163 627 26 103 8 163 626 25 103 8 163 625 24 104 8 164 624 23 104 8 164 628 26 107 8 169 627 25 107 8 170 626 24 108 8 170 625 23 108 8 171 619 17 111 8 175 628 25 111 8 176 627 24 112 8 177 626 23 112 8 178 628 24 116 8 183 527 23 117 8 184 523 19 120 8 190 528 23 121 8 191 524 19 126 8 198 525 19 131 8 207 523 17 135 7 212 526 19 136 7 215 524 17 140 7 222 427 19 141 7 223 425 17 146 7 231 428 19 147 7 231 426 17 152 7 240 427 17 158 6 249 428 17 164 6 259 4





401-312B 12/02/2009


Fertilizer Rate

The 3PYP planter does not presently offer a completefertilizer system with pump. Basic fertilizer rate is setby the pump system. Consult the documentation forthat system.

The optional fertilizer manifold does include a pressurerelief valve and orifice plates at each row unit drop line.These can affect fertilizer flow rate, and need to beconsidered when setting rates.

Adjust the relief valve per the 3PYP Operator’s Man-ual.

Orifice Plate SelectionIn general, the orifice ➀ needs to be small enough tocreate at least 15 psi of pressure in the manifold butlarge enough to prevent the manifold pressure fromexceeding 85 psi.

Wear protective gloves when changing orifice plates.

Refer to Figure 8

The minimum pressure is required to even out the flowof fertilizer between rows. To reduce orifice pluggingand pump wear, use the largest orifice practical foryour fertilizer application rate.

The best pressure range to maintain is 15-40 psi toensure optimum distribution while minimizing leakage.

IMPORTANT !Orifice size is only used to create 15-65 PSI backpressure to provide even flow between rows. Setapplication rate in gallons per acre using pump drivechart.

Figure 8Fertilizer Orifice Plate

21983

Orifice Size Great Plains Part Number20 832-052C

28*

*. These sizes are supplied withthe 3PYP fertilizer manifold.

832-056C

34* 832-053C

48* 832-054C

59 832-057C

80 832-055C

12/02/2009 401-312B


Orifice Size Charts

Gallons 30in Twin 36in Twin 38in Twin 40in Twinper Acre 15in Rows 30in Rows 20in Rowsat 5 mph Suggested Orifice Size

2.0 20 20 20 28 203.0 20 28 28 34 284.0 28 28 28 34 285.0 28 28 34 48 346.0 34 34 34 48 347.0 34 34 34 48 348.0 34 48 34 59 349.0 34 48 48 59 4810.0 48 48 48 59 4811.0 48 48 48 59 4812.0 48 48 48 59 48

29936

401-312B 12/02/2009


Appendix

Seed Lubricants

Singulator Plus Meters (all seeds)

Ezee Glide Plus Talc-Graphite Mix

821-069C bucket, 5 gallon (19 liter)

Ezee Glide Plus LubricantTo maximize performance of Great Plains metering sys-tems, it is imperative to use only “Ezee Glide Plus” lubri-cant. “Ezee Glide Plus” Talc-Graphite lubricant ismandatory for all seeds, especially treated or inoculatedseed. Thorough mixing of seed and added lubricantis required.

Recommended usage:

For clean seeds other than milo and cotton sprinkleone cup of Ezee Glide Plus Talc per 4 bushels or units(170 ml per 100 liters) of seed.

For milo and cotton double the application toone cup (or more) per 2 bu or units (335 ml per 100liters) of seed.

Adjust this rate as necessary so all seeds becomecoated while avoiding an accumulation of lubricant inthe bottom of the hopper.

For seed with excessive treatment, or for humid plantingenvironments, increase the rate as needed for smoothmeter operation.

Irritation and Chronic Exposure Hazard:Wear gloves. DO NOT use hands or any part of your body tomix seed lubricant. Wear a respirator when transferring andmixing. Avoid breathing lubricant dust. Not an acute hazard.May cause mechanical eye or skin irritation in high concen-trations. As with all mineral spills, minimize dusting duringclean-up. Prolonged inhalation may cause lung injury. Prod-uct can become slippery when wet.

Finger Pickup Meters

EZ-Slide Graphite Powder

821-042C bottle, 1 pound (450 grams)821-060C jug, 5 pound (2.3 kg)

For Finger Pick Up Meters OnlyUse only approved Graphite Powder available fromGreat Plains Mfg. Inc. or Precision Planting to ensureproper lubrication of finger pickup corn seed meters.

Recommended usage:

For finger pickup meters, add one tablespoon (15 ml) ofgraphite for each unit of seed corn (80,000 kernels).

In high humidity conditions, or seeds with heavy seedtreatments, increase the application to two tbsp (30ml).

If delivery of seed from the hopper to the finger meter isan issue, add “Ezee Glide Plus” talc and graphite blendat a rate of one cup (237ml) per 4 units of seed. Adjustuntil issue is resolved.

Irritation and Chronic Exposure Hazard:Wear gloves. DO NOT use hands or any part of your body tomix seed lubricant. Wear a respirator when transferring andmixing. Avoid breathing lubricant dust. Not an acute hazard.May cause mechanical eye or skin irritation in high concen-trations. As with all mineral spills, minimize dusting duringclean-up. Prolonged inhalation may cause lung injury.

29248 25477

12/02/2009 401-312B

Great Plains Mfg., Inc.

EOD

401-312B 12/02/2009

Great Plains Manufacturing, Inc.Corporate Office: P.O. Box 5060Salina, Kansas 67402-5060 USA

seed rate charts - great plains ag · 401-312b 12/02/2009 setting meter rate hydraulic drive meter...

Documents