section 1000 index - major eng section 1000.pdf · section 1000 index dispense liquid, by gravity,...

1P. O. BOX 1207, MANITOWOC, WI 54221-1207 (920) 682-6173 FAX (920) 682-7699

Internet http://www.oilrite.com e-mail [email protected]

Sectio

n 1000 In

dex

AIR OPERATED DISPENSERS .............13

CONSTANT LEVEL OILERS INSTALLATION INSTRUCTIONS...........16

CONSTANT LEVEL OILERS.................2-3

FULL FLOW DISPENSER.....................8-9

HORIZONTAL DISPENSERS & STEELTANKS.....................................................12

MULTIPLE FEED OILERS.....................6-7

RESERVOIRS ....................................10-11

SINGLE FEED OILERS.........................4-5

SPARE PARTS...................................14-15

Section 1000 Index

Dispense liquid, by gravity, from a reservoir, through an electro or manualshutoff valve. Acrylic, pyrex or polycarbonate reservoirs available.Additional sight feed valves are neededfor the regulation of liquid flow.

Dispense liquid, by gravity, from a reservoir, which are furnished withoutshutoffs or control valves.

Horizontal dispensers dispense liquid bygravity, from a reservoir, with flow con-trolled by means of a shutoff valve.Steel tanks dispense oil by gravity froma reservoir without flow valves or shutoff.

Dispense liquid, by air pressure, from areservoir to elevated, distant and inaccessible points.

Will maintain a fixed liquid level in abearing housing or gear box vital in preventing possible machine breakdowndue to insufficient lubrication.

Deliver a pre-adjusted rate of liquid, bygravity from a reservoir, through a nor-mally closed solenoid or toggle shutoffvalve to an adjustable needle valve,which has a friction lock to retain its set-ting.

Liquid is released, by gravity, from areservoir, through a normally closedsolenoid or toggle shutoff valve to thenew modular stacked multiple sight feedvalves.

Co

nst

ant

Lev

el O

ilers



CONSTANT LEVEL LUBRICATOR WITH LOW LEVELSAFETY SWITCHES will maintain a fixed liquid level withinthe bearing housing, vital in protecting bearings from failureand preventing possible machine breakdown due to insufficient lubrication. A safeguard against loss of lubricantis provided by a low level safety switch. The low level switchcan be used to actuate warning devices or shut off amachine, thus protecting costly machinery.

Operation is based on the liquid seal principle. Wheneverthe liquid level recedes below the set level because of liquidconsumption, the liquid seal on the spout, inside the lubricator, is temporarily broken. This allows air from the airintake to enter the reservoir, releasing the liquid until a sealand proper level are again established.

To refill unit, remove reservoir cap. An automatic shutoffwill hold the liquid supply in the reservoir while refilling. Afterfilling, screw cap on tightly and lubricator will resume normalfunctioning.

SPECIFICATIONS:

• Pressure Atmospheric Pressure• Temperature 160° F. Max.• Reservoir Acrylic• Seals Buna-N• Covers Aluminum Alloy• Body Aluminum Alloy• Level Switch Stainless Steel

Constant Level OilersOIL-RITE SERVICE TO DESIGN

AND PLANT ENGINEERS

Whether you are seeking the proper lubrication equipmentfor a machine still in the design stage, or for machineryalready in use, Oil-Rite can help you. Oil-Rite engineers, withall their accumulated knowledge and skills, will study yourlubrication problem and help you select precisely the rightequipment for your individual application. There’s no obliga-tion.

CAPACITY SELECTOR GUIDE-DROP FEED OILERSThe selection of reservoir capacity for drop feed oilersshould take into consideration:

1. Number of drops per minute to be dispensed.2. Desired interval between refill.3. Number of feed outlets in case of multiple oilers.4. Continuous or intermittent operations.

Table 1 serves as a guide and permits selection of areservoir for individual needs.

TABLE 1

Reservoir capacity in fluid oz.*1 hour 8 hours 24 hours 5 days

1 .11 .9 2.8 142 .23 1.8 5.5 283 .34 2.8 8.3 415 .57 4.6 14.0 697 .80 6.4 19.0 96

10 1.15 9.2 28.0 13815 1.72 14.0 41.0 20720 2.30 18.0 55.0 27525 2.87 23.0 69.0 34430 3.44 28.0 83.0 413*based on liquid drops of 3/16 dia.

Most drop feed oilers usually deliver drops of approx-imately 3/16 dia. Smaller or larger drops will, ofcourse, necessitate a decrease or increase of thereservoir capacity given in Table 1. To obtain the prop-er reservoir capacity for 1/8 dia. or 1/4 dia. drops, sim-ply multiply the ounce capacity shown in Table 1 withthe respective multiplier given in Table 2.

TABLE 2Number of

Diameter drops inof drops 1 fluid oz. Multiplier

1/8 1765 .02963/16 523 1.1/4 221 2.37

TABLE 3-LIQUID MEASURE1 U.S. gal. = 128 fluid oz. = 231 cu. in.

= 4 quarts = 8 pints= 3.785 liters = 3785 c.c.

1 Fluid oz. = 1.805cu. in. = 29.57c.c.1 Cubic in. = 16.39 c.c. = .554 fluid oz.1 Liter = 1000 c.c.

= .264 U.S. gal. = 1.057 quarts= 61.023 cu. in. = 33.814 fluid oz.

Numberof drops

per minute

Reed Switch MagneticallyActuatedNormally OpenMax. Resistance Load

120 Volt A.C. .4A.240 Volt A.C. .2A.480 Volt A.C. N/R

24 Volt D.C. .5A.120 Volt D.C. .2A.240 Volt D.C. .1A.

NOTE: For safety, long life, and bestperformance use this liquid levelswitch with Oil-Rite relay No.A-3160, A-3138 or A-4621 (seepage 72) having a D.P.D.T. switch for10 AMPS 115 Volts 60 Hertz.

When Ordering Specify:• Catalog Number

Catalog Number

B-2443-1B-2443-2

Capacity

1/2 GAL.1 GAL.

B

131/8

181/8

C

157/16

207/16

Style C

**

* Special - Please Consult Factory



Co

nstan

t Level O

ilers

Catalog NumberAcrylic Pyrex

B-576-1 B-576-11B-576-2 B-576-12B-576-3 B-576-13

B-576-4 B-576-14B-576-5 B-576-15B-576-6 B-576-16B-576-7 —B-737-1 B-737-11B-737-2 B-737-12B-737-3 B-737-13

B-737-4 B-737-14B-737-5 B-737-15B-737-6 B-737-16B-737-7 —

Capacity A B C

21/2 OZ. 2 51/4 71/16

5 OZ. 21/2 53/4 79/16

9 OZ. 3 69/16 83/8

1 PT. 31/2 79/16 93/8

1 QT. 41/4 813/16 105/8

1/2 GAL. 51/2 1013/16 125/8

1 GAL. 51/2 1513/16 175/8

21/2 OZ. 2 51/4 83/8

5 OZ. 21/2 53/4 87/8

9 OZ. 3 69/16 911/16

1 PT. 31/2 79/16 1011/16

1 QT. 41/4 813/16 1115/16

1/2 GAL. 51/2 1013/16 1315/16

1 GAL. 51/2 1513/16 1815/16

Fig.

1

2


B-518-1 B-518-11B-518-2 B-518-12B-518-3 B-518-13B-518-4 B-518-14B-518-5 B-518-15B-518-6 B-518-16B-518-7 —

B-543-1 B-543-11B-543-2 B-543-12B-543-3 B-543-13B-543-4 B-543-14B-543-5 B-543-15B-543-6 B-543-16B-543-7 —

Capacity A B C

21/2 OZ. 2 53/16 63/8

5 OZ. 21/2 511/16 67/8

9 OZ. 3 61/2 711/16

1 PT. 31/2 71/2 811/16

1 QT. 41/4 83/4 111/16

1/2 GAL. 51/2 103/4 131/16

1 GAL. 51/2 153/4 181/16

21/2 OZ. 2 53/16 75/8

5 OZ. 21/2 511/16 81/8

9 OZ. 3 61/2 815/16

1 PT. 31/2 71/2 915/16

1 QT. 41/4 83/4 113/16

1/2 GAL. 51/2 103/4 133/16

1 GAL. 51/2 153/4 183/16

Fig.

1

2

3

Constant Level OilersCONSTANT LEVEL OILERS are built to give long, trouble freeservice. The finest materials and workmanship are incorporat-ed throughout. They will maintain a fixed liquid level in a bear-ing housing or gear box.

When the liquid in the bearing recedes because of liquidconsumption, the liquid seal on the inside of the lubricator istemporarily broken. This allows air from the air intake to enterthe lubricator reservoir, releasing the liquid until a seal andproper level are again established.

The Style CS Constant Level Oiler is identical in design toStyle C with two exceptions. A large sight for viewing the liquid level and condition of the liquid is provided, plus thereare larger liquid outlets for rugged, heavy duty installations.

For reference, a liquid level line is scribed on the base.Units are easily refilled through a top filler cap.The reservoirneed not be removed for refilling. A shutoff valve holds the liquid in the reservoir when the filler cap is removed. After the

cap is screwed down again, the lubricator resumes normalfunctioning.

An air vent is supplied which can be piped back to the bearing or gear box thereby equalizing any existing pressureor vacuum. The reservoir is crystal clear glass or shatterproofacrylic permitting the liquid supply to be visible at all times.

SPECIFICATIONS:• Pressure Atmospheric Pressure• Temperature 160° F. Maximum Acrylic

225° F. Maximum Pyrex• Reservoir Acrylic or Pyrex• Seals Buna-N• Sight Glass• Covers Aluminum Alloy• Body Aluminum Alloy


Style CStyle CS


**

**

**

**

4

Sin

gle

Fee

d E

lect

ro O

ilers

Model NumberAcrylic Pyrex

B-1875-1 B-1875-21B-1875-2 B-1875-22B-1875-3 B-1875-23B-1875-4 B-1875-24B-1875-5 B-1875-25B-1875-6 B-1875-26B-1875-7 B-1875-27B-1875-8 B-1875-28B-1875-9 B-1875-29B-1875-10 B-1875-30B-1875-11 B-1875-31B-1875-12 B-1875-32

B-1875-13 B-1875-33B-1765-1 B-1765-5B-1765-2 —

B-1875-16 B-1875-36B-1875-17 B-1875-37B-1875-18 B-1875-38B-1875-19 B-1875-39B-1875-20 B-1875-40B-1765-3 B-1765-7B-1765-4 —

Model NumberPolycarbonate

B-1763-1B-1763-2B-1763-3B-1763-4B-1763-5B-1763-6B-1763-7B-1763-8B-1763-9B-1763-10B-1763-11B-1764-1B-1764-2B-1764-3B-1764-4B-1764-7B-1763-12B-1763-13B-1763-14B-1763-15B-1764-5B-1764-6B-1764-8

5/8-18 NF THD.FOR REMOTE

MOUNTINGWITH 1/8

FEMALE NPTOUTLET

Capacity

1 OZ

21/2 OZ.

5 OZ.

9 OZ.

1 PT.

1 QT.1/2 GAL.

1 OZ21/2 OZ.5 OZ.9 OZ.1 PT.1 QT.

1/2 GAL.

Thread Size A C D

1/8 MALE N.P.T. 2 53/163/8

1/4 MALE N.P.T. 2 51/47/16

1/8 MALE N.P.T. 2 63/163/8

1/4 MALE N.P.T. 2 61/47/16

3/8 MALE N.P.T. 2 63/81/2

1/8 MALE N.P.T. 27/8 63/163/8

1/4 MALE N.P.T. 27/8 61/47/16

3/8 MALE N.P.T. 27/8 63/81/2

1/4 MALE N.P.T. 27/8 71/27/16

3/8 MALE N.P.T. 27/8 75/81/2

1/2 MALE N.P.T. 27/8 73/45/8

1/4 MALE N.P.T. 35/8 813/167/16

3/8 MALE N.P.T. 35/8 815/161/2

1/2 MALE N.P.T. 35/8 91/165/8

1/2 MALE N.P.T. 35/8 127/165/8

1/2 MALE N.P.T. 5 135/165/8

2 59/165/8

2 69/165/8

27/8 69/165/8

27/8 713/163/8

35/8 91/85/8

35/8 121/25/8

5 133/85/8

Single Feed Electro Oilers

When Ordering Specify:• Model Number• Voltage and Frequency


5/8-18 N.F. THD.FOR REMOTE

MOUNTINGWITH 1/8

FEMALE N.P.T.OUTLET

SINGLE FEED ELECTRO OILERS deliver a pre-adjusted rateof liquid, by gravity from a reservoir, through a normally closedsolenoid valve to an adjustable needle valve, which has a friction lock to retain its setting.

These units are simple, yet efficient.The drop feeding of theliquid can easily be observed through a lower sight chamber.Flow is controlled by wiring the normally closed solenoid valveacross the line of the drive motor, providing automatic operation. The solenoid can be operated by a separate switchor timer for intermittent use.

Durable, shatterproof acrylic reservoirs are for tempera-tures below 160° F. Crystal clear pyrex or polycarbonate reservoirs are available for temperatures below 225° F. A self-closing filler cap is provided on top of the reservoir.

SPECIFICATIONS:• Pressure Atmospheric Pressure

Gravity Feed OnlyReservoir and Sight Vented

• Temperature 160° F. Max. Acrylic225° F. Max. Pyrex or Polycarbonate

• Metering Adjustable Needle Valve andSolenoid Shutoff

• Reservoir Acrylic,Polycarbonate or Pyrex• Seals Buna-N• Sight Glass• Covers Aluminum Alloy or Polypropylene• Body Aluminum Alloy• Shank Steel, Plated

Style DE Style DE

**********

**********

*

***

* Special - PleaseConsult Factory

Thread Size A C D

1/8 MALE N.P.T. 2 513/163/8

1/4 MALE N.P.T. 2 57/87/16

3/8 MALE N.P.T. 2 515/161/2

1/8 MALE N.P.T. 21/2 65/163/8

1/4 MALE N.P.T. 21/2 63/87/16

3/8 MALE N.P.T. 21/2 67/161/2

1/4 MALE N.P.T. 3 75/167/16

3/8 MALE N.P.T. 3 73/81/2

1/2 MALE N.P.T. 3 71/25/8

1/4 MALE N.P.T. 31/2 85/167/16

3/8 MALE N.P.T. 31/2 83/81/2

1/2 MALE N.P.T. 31/2 81/25/8

1/2 MALE N.P.T. 41/4 97/85/8

1/2 MALE N.P.T. 51/2 12 5/8

1/2 MALE N.P.T. 51/2 17 5/8

2 63/165/8

21/2 611/165/8

3 75/85/8

31/2 85/85/8

41/4 915/165/8

51/2 121/165/8

51/2 171/165/8

21/2OZ.

5 OZ.

9 OZ.

1 PT.

1QT.1/2 GAL.1 GAL.

21/2 OZ.5 OZ.9 OZ.1 PT.1 QT.

1/2 GAL.1 GAL.

Capacity

5

2 51/165/8

2 61/165/8

27/8 6 5/8

27/8 71/45/8

35/8 85/85/8

35/8 12 5/8

5 127/85/8


MOUNTINGWITH 1/8

FEMALE N.P.T.OUTLET

Thread Size A C D

1/8 MALE N.P.T. 2 51/43/8

1/4 MALE N.P.T. 2 55/167/16

3/8 MALE N.P.T. 2 53/81/2

1/8 MALE N.P.T. 21/2 53/43/8

1/4 MALE N.P.T. 21/2 513/167/16

3/8 MALE N.P.T. 21/2 57/81/2

1/4 MALE N.P.T. 3 63/47/16

3/8 MALE N.P.T. 3 613/161/2

1/2 MALE N.P.T. 3 615/165/8

1/4 MALE N.P.T. 31/2 73/47/16

3/8 MALE N.P.T. 31/2 713/161/2

1/2 MALE N.P.T. 31/2 715/165/8

1/2 MALE N.P.T. 41/4 95/165/8

1/2 MALE N.P.T. 51/2 117/165/8

1/2 MALE N.P.T. 51/2 167/165/8

2 55/85/8

21/2 61/85/8

3 71/165/8

31/2 81/165/8

41/4 93/85/8

51/2 111/25/8

51/2 161/25/8

Catalog No.Polycarbonate

B-1681-1B-1681-2B-1681-3B-1681-4B-1681-5B-1681-6B-1681-7B-1681-8B-1681-9B-1681-10B-1681-11

B-1682-1B-1682-2

B-1682-3B-1682-4B-1682-7B-1681-12

B-1681-13B-1681-14B-1681-15B-1682-5B-1682-6B-1682-8

Capacity

1 OZ.

21/2 OZ.

5 OZ.

9 OZ.

1 PT.

1 QT.1/2 GAL.

1 OZ.21/2 OZ.5 OZ.9 OZ.1 PT.

1 QT.1/2 GAL.

Sin

gle F

eed M

anu

al Oilers

DROP FEED MANUAL OILERS deliver a pre-adjusted rate ofliquid, by gravity, from a reservoir, through an adjustable nee-dle valve which has a friction lock to retain its setting.

These units are simple, yet efficient. A toggle shutoff is pro-vided which starts and stops the liquid flow but will not affectthe metering adjustment. The controlled feed rate can beobserved through the lower sight chamber.

Durable, shatterproof acrylic reservoirs are for tempera-tures below 160° F. Crystal clear pyrex or polycarbonate reser-voirs are available for temperatures below 225° F. A self-clos-ing filler cap is located on top of the reservoir.

SPECIFICATIONS:• Pressure Atmospheric Pressure

Gravity Feed OnlyReservoir and Sight Vented


• Metering Adjustable Needle Valve andToggle Shutoff

• Reservoir Acrylic,Polycarbonate or Pyrex• Seals Buna-N• Sight Glass• Shank Steel, Plated• Covers Aluminum Alloy or Polypropylene• Body Aluminum Alloy



B-1876-1 B-1876-21B-1876-2 B-1876-22B-1876-3 B-1876-23B-1876-4 B-1876-24

B-1876-5 B-1876-25B-1876-6 B-1876-26B-1876-7 B-1876-27B-1876-8 B-1876-28B-1876-9 B-1876-29B-1876-10 B-1876-30B-1876-11 B-1876-31B-1876-12 B-1876-32B-1876-13 B-1876-33B-1715-1 B-1715-5B-1715-2 —

B-1876-16 B-1876-36B-1876-17 B-1876-37B-1876-18 B-1876-38B-1876-19 B-1876-39B-1876-20 B-1876-40B-1715-3 B-1715-7B-1715-4 —

Capacity

21/2OZ.

5 OZ.

9 OZ.

1 PT.

1QT.1/2 GAL.1 GAL.

21/2 OZ.5 OZ.9 OZ.1 PT.1QT.

1/2 GAL.1 GAL.



MOUNTINGWITH 1/8

FEMALE N.P.T.OUTLET

Thread Size A C D

1/8 MALE N.P.T. 2 411/163/8

1/4 MALE N.P.T. 2 43/47/16

1/8 MALE N.P.T. 2 511/163/8

1/4 MALE N.P.T. 2 53/47/16

3/8 MALE N.P.T. 2 57/81/2

1/8 MALE N.P.T. 27/8 511/163/8

1/4 MALE N.P.T. 27/8 53/47/16

3/8 MALE N.P.T. 27/8 57/81/2

1/4 MALE N.P.T. 27/8 7 7/16

3/8 MALE N.P.T. 27/8 71/81/2

1/2 MALE N.P.T. 27/8 71/45/8

1/4 MALE N.P.T. 35/8 85/167/16

3/8 MALE N.P.T. 35/8 87/161/2

1/2 MALE N.P.T. 35/8 89/165/8

1/2 MALE N.P.T. 35/8 1115/165/8

1/2 MALE N.P.T. 5 1213/165/8

Style DOSFStyle DOSF

*********

***


6


B-3152-1 B-3152-11B-3152-2 B-3152-12B-3152-3 B-3152-13B-3152-4 B-3152-14B-3152-5 B-3152-15B-3152-6 —

Mu

ltip

le F

eed

Ele

ctro

Oile

rs

Multiple Feed Electro OilersSPECIFICATIONS:

• Pressure Atmospheric PressureGravity Feed OnlyReservoir and Sight Are Vented


• Metering Adjustable Needle Valve withSolenoid Shutoff

• Reservoir Acrylic, Polycarbonate or Pyrex• Valves Aluminum Alloy• Seals Buna-N (Other Material Available)• Sight Glass• Shank Steel, Plated• Covers Aluminum Alloy or Polypropylene• Body Aluminum Alloy• Connector Kit Buna-N (Other Material Available)

MULTIPLE FEED ELECTRO OILERS have been revolution-ized by utilizing a new manifold, multiple sight feed valve sys-tem. This exclusive and unique feature allows, for the firsttime, the option of changing the units in the field by merelystacking them together.

Liquid is released, by gravity, from a reservoir, through anormally closed solenoid valve to the new modular stackedmultiple sight feed valves. Each valve is a complete unit thatinterlocks and seals with the preceding valve.

Up to 24 sight feed valves can be separately adjusted andthe setting retained by means of a friction lock. Drop feedingof liquid to widely separated points can be controlled andobserved from one central location.

The highest standard of quality is built into these Oil-Ritewater resistant solenoid valves.The compact solenoid is usu-ally wired across the line of the drive motor. The solenoid canbe operated by a separate switch or timer for intermittent operation.

When Ordering Specify:• Model Number• Voltage and Frequency• Number of Feeds


B-3192-2B-3192-3B-3192-4B-3192-5

Capacity

9 OZ.1 PT.1 QT.

1/2 GAL.

A

27/8

35/8

35/8

5

C

91/16

101/16

137/16

141/8

Capacity

5 OZ.9 OZ.1 PT.1 QT.

1/2 GAL.1 GAL.

C

73/4

89/16

99/16

111/8

131/8

181/8

B

33/8

43/16

53/16

63/4

83/4

133/4

A

21/2

331/2

41/4

51/2

51/2

Style DE Style DE

Feeds

LM

3

23/4

411/16

4

23/4

57/16

5

31/2

63/16

6

31/2

615/16

12

53/4

117/16

24

101/4

207/16

2

2315/16

Feeds

LM

3

23/4

411/16

4

23/4

57/16

5

31/2

63/16

6

31/2

615/16

12

53/4

117/16

24

101/4

207/16

2

2315/16

Connector KitA-5671-1

Additional Valves Specify PartNumber B-3151-1

When Ordering Specify:• Model Number• Voltage and Frequency• Number of Feeds

**




7

Mu

ltiple F

eed M

anu

al Oilers

SPECIFICATIONS:

• Pressure Atmospheric PressureGravity Feed OnlyReservoir and Sight Are Vented


• Metering Adjustable Needle Valve with ToggleShutoff

• Reservoir Acrylic, Polycarbonate or Pyrex• Valves Aluminum Alloy• Seals Buna-N• Sight Glass• Shank Steel, Plated• Covers Aluminum Alloy or Polypropylene• Body Aluminum Alloy• Connector Kit Buna-N (Other Material Available)

MULTIPLE FEED MANUAL OILERS have been revolution-ized by utilizing a new manifold, multiple sight feed valve sys-tem. This exclusive and unique feature allows, for the firsttime, the option of changing the units in the field by merelystacking them together.

Liquid is released, by gravity, from a reservoir, through atoggle shutoff valve which is located below the reservoir, tothe new modular stacked multiple sight feed valves. Eachvalve is a complete unit that interlocks and seals with the pre-ceding valve.

Up to 24 sight feed valves can be separately adjusted andthe setting retained by means of a friction lock. Drop feedingof liquid to widely separated points can be controlled andobserved from one central location.


B-3153-1 B-3153-11B-3153-2 B-3153-12B-3153-3 B-3153-13B-3153-4 B-3153-14B-3153-5 B-3153-15B-3153-6 —

Feeds

LM

3

23/4

411/16

4

23/4

57/16

5

31/2

63/16

6

31/2

615/16

12

53/4

117/16

24

101/4

207/16

2

2315/16

When Ordering Specify:• Model Number• Number of Feeds

When Ordering Specify:• Model Number• Number of Feeds


B-3193-2B-3193-3

B-3193-4B-3193-5

Capacity

9 OZ.

1 PT.1QT.

1/2 GAL.

A

27/8

35/8

35/8

5

C

91/16

101/16

137/16

141/8

Capacity


1/2 GAL.1 GAL.

C

73/4

89/16

99/16

111/8

131/8

181/8

B

33/8

43/16

53/16

63/4

83/4

133/4

A

21/2

3

31/2

41/4

51/2

51/2

Multiple Feed Manual Oilers

Style DM Style DM

Feeds

LM

3

23/4

411/16

4

23/4

57/16

5

31/2

63/16

6

31/2

615/16

12

53/4

117/16

24

101/4

207/16

2

2315/16


**








B-2084-2 B-2084-12B-2084-3 B-2084-13B-2084-4 B-2084-14

B-2084-5 B-2084-15B-2084-6 B-2084-16B-2084-7 B-2084-17B-2084-8 —

Fu

ll F

low

Ele

ctro

Dis

pen

sers

Full Flow Electro DispensersSPECIFICATIONS:

• Pressure Atmospheric PressureGravity Feed OnlyReservoir is Vented


• Metering Full Flow with Solenoid Shutoff• Reservoir Acrylic,Polycarbonate or Pyrex• Seals Buna-N• Shank Aluminum Alloy• Covers Aluminum Alloy or Polypropylene• Body Aluminum Alloy• Port 1/4” Dia.

FULL FLOW ELECTRO DISPENSERS dispense liquid froma reservoir, by gravity, through an electro shutoff valve.

Designed to serve as a central reservoir of an oiling sys-tem, additional sight feed valves are needed for the regula-tion of liquid flow.

Flow is controlled by a normally closed solenoid valve.The compact solenoid is usually wired across the line of thedrive motor providing automatic shutoff. The solenoid valvecan be operated by a separate switch or timer for intermittentoperation.

Durable, shatterproof acrylic reservoirs are for tempera-tures below 160° F. Crystal clear pyrex or polycarbonatereservoirs are available for temperatures below 225° F. Aself-closing filler cap is provided on top of the reservoir.




B-1733-1B-1733-2B-1733-3B-1733-4B-1733-5B-1733-6B-1733-7

Capacity

1 OZ.21/2 OZ.5 OZ.9 OZ.1 PT.1 QT.

1/2 GAL.

A

2

27/8

35/8

5

B

43/16

53/16

51/8

63/8

711/16

111/16

1115/16

Capacity

21/2 OZ.5 OZ.9 OZ.

1 PT.1 QT.

1/2 GAL.1 GAL.

A

2

21/2

3

31/2

41/4

51/2

51/2

B

43/4

51/4

63/16

73/16

81/2

105/8

155/8

C

53/8

57/8

613/16

713/16

91/8

111/4

161/4

Style DEF Style DEF

***




Fu

ll Flo

w M

anu

al Disp

ensers

SPECIFICATIONS:

• Pressure Atmospheric PressureGravity Feed OnlyReservoir is Vented


• Metering Full Flow with Toggle Shutoff • Reservoir Acrylic,Polycarbonate or Pyrex• Seal Buna-N• Shank Aluminum Alloy• Covers Aluminum Alloy or Polypropylene• Body Aluminum Alloy• Port 1/4” Dia.

FULL FLOW MANUAL DISPENSERS dispense liquid, bygravity, from a reservoir, through a toggle shutoff valve.


Flow is controlled by a toggle shutoff valve mountedbelow the dispenser.

Durable, shatterproof acrylic reservoirs are for tempera-tures below 160° F. Crystal clear pyrex or polycarbonatereservoirs are available for temperatures below 225° F. Aself-closing filler cap is provided on top of the reservoir.


B-2083-2 B-2083-12B-2083-3 B-2083-13B-2083-4 B-2083-14B-2083-5 B-2083-15B-2083-6 B-2083-16B-2083-7 B-2083-17B-2083-8 —



Catalog NumberPolycarbonate

B-1734-1B-1734-2B-1734-3B-1734-4

B-1734-5B-1734-6B-1734-7

Capacity

1 OZ.

21/2 OZ.5 OZ.9 OZ.1 PT.1 QT.

1/2 GAL.

A

2

27/8

35/8

5

B

43/16

53/16

51/8

63/8

711/16

111/16

1115/16

Capacity

2 1/2 OZ.5 OZ.9 OZ.1 PT.1 QT.

1/2 GAL.1 GAL.

A

2

21/2

331/2

41/4

51/2

51/2

B

43/4

51/4

63/16

73/16

81/2

105/8

155/8

C

53/8

57/8

613/16

713/16

91/8

111/4

161/4

Full Flow Manual Dispensers

Style DFFStyle DFF

***


P. O. BOX 1207, MANITOWOC, WI 54221-1207 (920) 682-6173 FAX (920) 682-7699Internet http://www.oilrite.com e-mail [email protected]

5/8-18 N.F.FOR REMOTE

MOUNTINGWITH 1/8

FEMALE NPTOUTLET

Thread Size A B C D

1/8 MALE N.P.T. 11/2 25/8 3 3/8

1/4 MALE N.P.T. 11/2 25/8 31/167/16

1/8 MALE N.P.T. 2 37/16 313/163/8

1/4 MALE N.P.T. 2 37/16 37/87/16

3/8 MALE N.P.T. 2 37/16 315/161/2

1/8 MALE N.P.T. 21/2 315/16 45/163/8

1/4 MALE N.P.T. 21/2 315/16 43/87/16

3/8 MALE N.P.T. 21/2 315/16 47/161/2

1/4 MALE N.P.T. 3 47/8 55/167/16

3/8 MALE N.P.T. 3 47/8 53/81/2

1/2 MALE N.P.T. 3 411/16 55/165/8

1/4 MALE N.P.T. 31/2 57/8 65/167/16

3/8 MALE N.P.T. 31/2 57/8 63/81/2

1/2 MALE N.P.T. 31/2 511/16 65/165/8

1/2 MALE N.P.T. 41/4 71/16 711/165/8

1/2 MALE N.P.T. 51/2 91/8 93/45/8

1/2 MALE N.P.T. 51/2 141/8 143/45/8

11/2 27/16 31/165/8

2 31/4 37/85/8

21/2 33/4 43/85/8

3 411/16 55/165/8

31/2 511/16 65/165/8

41/4 71/16 711/165/8

51/2 91/8 93/45/8

51/2 141/8 143/45/8

Capacity

1 OZ.

21/2OZ.

5 OZ.

9 OZ.

1 PT.

1QT.1/2 GAL.1 GAL.1 OZ.

21/2 OZ.5 OZ.9 OZ.1 PT.1QT.

1/2 GAL.1 GAL.

Capacity

1 OZ.

21/2 OZ.

5 OZ.

9 OZ.

1 PT.

1 QT.

1/2 GAL.

1 OZ.21/2 OZ.5 OZ.9 OZ.1 PT.1 QT.

1/2 GAL.

2 31/45/8

2 41/45/8

27/8 41/45/8

27/8 51/25/8

35/8 613/165/8

35/8 103/165/8

5 111/165/8

Thread Size A C D

1/8 MALE N.P.T. 2 3 3/8

1/4 MALE N.P.T. 2 31/167/16

1/8 MALE N.P.T. 2 4 3/8

1/4 MALE N.P.T. 2 41/167/16

3/8 MALE N.P.T. 2 41/81/2

1/8 MALE N.P.T. 27/8 4 3/8

1/4 MALE N.P.T. 27/8 41/167/16

3/8 MALE N.P.T. 27/8 41/81/2

1/4 MALE N.P.T. 27/8 53/167/16

3/8 MALE N.P.T. 27/8 53/81/2

1/2 MALE N.P.T. 27/8 51/25/8

1/4 MALE N.P.T. 35/8 613/167/16

3/8 MALE N.P.T. 35/8 67/81/2

1/2 MALE N.P.T. 35/8 613/165/8

1/4 MALE N.P.T. 35/8 103/167/16

1/2 MALE N.P.T. 35/8 103/165/8

1/4 MALE N.P.T. 5 107/87/16

1/2 MALE N.P.T. 5 111/165/8

SPECIFICATIONS:

• Pressure Atmospheric PressureGravity Feed OnlyReservoir Vented

• Temperature 225° F. Max. Polycarbonate or Pyrex160° F. Max. Acrylic

• Reservoir Acrylic,Polycarbonate or Pyrex• Seals Buna-N• Mtg. Shank Steel, Plated• Covers Aluminum Alloy or Polypropylene

OIL CUPS dispense liquid, by gravity, from a reservoir andare furnished without shutoff or control valves.

These dispensers are designed to serve as a centralreservoir of an oiling system. Shutoff valves and additionalsight feed valves are needed for the regulation of liquid flow.

Durable, shatterproof acrylic reservoirs are for tempera-tures below 160°F. Crystal clear pyrex or polycarbonatereservoirs are available for temperatures below 225°F. Theyare also useful for many applications where it is desirableto visually inspect the presence and clarity of the liquid.Self-closing filler caps are also provided.

Catalog NumberPolycarbonate

B-1748-1B-1748-2B-1748-3B-1748-4B-1748-5B-1748-6B-1748-7B-1748-8B-1748-9

B-1748-10B-1748-11B-1748-12B-1748-13B-1748-14B-1748-24B-1748-15B-1748-25B-1748-23B-1748-16B-1748-17B-1748-18B-1748-19

B-1748-20B-1748-21B-1748-22



B-966-1 B-966-51B-966-2 B-966-52B-966-3 B-966-53B-966-4 B-966-54B-966-5 B-966-55B-966-6 B-966-56B-966-7 B-966-57B-966-8 B-966-58B-966-9 B-966-59B-966-10 B-966-60B-966-11 B-966-61B-966-12 B-966-62B-966-13 B-966-63B-966-14 B-966-64B-966-15 B-966-65B-966-16 B-966-66B-966-17 —B-966-18 B-966-68B-966-19 B-966-69B-966-20 B-966-70B-966-21 B-966-71B-966-22 B-966-72B-966-23 B-966-73B-966-24 B-966-74B-966-25 —


5/8-18 N.F. FORREMOTE MTG.

WITH 1/8

FEMALEN.P.T. OUTLET

Oil

Cu

p R

eser

voir

s

Reservoirs

Style D Style D

*


**********

*

****

11

Reservoirs cont.F

ilter and

Lo

w L

evel Sen

sor R

eservoir

TEN OUNCE RESERVOIR ASSEMBLY dispenses liquid, bygravity. This reservoir is injection molded polycarbonate andthe enclosure cap is injection molded polypropylene.

This reservoir is ideal for many applications. As an oil cup,it can be directly mounted to bearing housing, gear box, transmission, etc. It can also be assembled with a remote mounting shank, allowing for the reservoir to be mountedaway from the point of application.

The polycarbonate reservoir is transparent, allowing forvisual inspection of contents, and is compatible with a widerange of fluids. It will tolerate temperature changes fromminus 40° F. to maximum of 150° F. without any significantdimensional changes. It is shatterproof, making it well suitedfor rugged industrial applications, as well as areas whereglass is not permitted.

SPECIFICATIONS:• Pressure Atmospheric Pressure• Temperature 150° F. Maximum• Reservoir Polycarbonate• Seals Viton®• Mtg. Shank Steel, Plated• Cover Polypropylene

5/8-18 U.N.F. FORREMOTE MTG. WITH

1/8 FEMALE N.P.T.OUTLET


B-3177-2 B-3177-52B-3177-3 B-3177-53

B-3177-7 B-3177-57B-3177-11 —B-3177-13 B-3177-63B-3177-14 B-3177-64B-3177-15 —

Capacity Thread Size A C

10 OZ. 1/4 MALE N.P.T. 27/8 59/16

Catalog NumberWith Filter Without Filter

A-5409-1 A-5409-2

Capacity Thread Size A C

1 QT. 3/8 MALE N.P.T. 41/4 73/4

1QT. 1/2 MALE N.P.T. 41/4 73/4

1/2 GAL. 1/2 MALE N.P.T. 51/2 913/16

1 GAL. 1/2 MALE N.P.T. 51/2 1413/16

1QT. 41/4 73/4

1/2 GAL. 51/2 913/16

1 GAL. 51/2 1413/16

RESERVOIR WITH FILTER AND LOW LEVEL SENSORdispenses liquid, by gravity, from a reservoir and are furnished without shutoff or control valves.

These dispensers are designed to serve as a centralreservoir of an oiling system. Shutoff valves and additionalsight feed valves are needed for the regulation of liquid flow.

Durable, shatterproof acrylic reservoirs are for tempera-tures below 160°F. Crystal clear pyrex or acrylic reservoirsare available for temperatures below 225°F. They are alsouseful for many applications where it is desirable to visuallyinspect the presence and clarity of the liquid. Self-closingfiller caps are also provided.

SPECIFICATIONS:• Pressure Atmospheric Pressure• Temperature 225° F. Max. Pyrex

160° F. Max. Acrylic• Reservoir Acrylic or Pyrex• Seals Buna-N• Low-Level Switch Polypropylene• Filter 100 Mesh• Covers Aluminum Alloy

**

*


SPECIFICATIONS:

• Pressure 15 P.S.I. Max. • Cover Polypropylene• Gasket Buna-N • Reservoir Polycarbonate• Temperature -40º F to 225° F. Max.

POLYCARBONATE BOTTLES are fully transparent, sturdy,with rigid walls, almost indestructible, stain-resistant, andhave a chemical resistance to wide range of fluids.

They can be used for a multitude of applications such ascontainers for storage, laboratory experiments, shipping ofparts or liquids and oil dispensing reservoirs. The bottles arealso ideal for retaining samples of chemical or medical prod-ucts.

The bottles possess good fire resistant properties. Theywill permit the use of conventional marking or identifyingtechniques such as adhesive labels, silk screening, printingmarkers, etc.

The enclosure caps used are made of ultraviolet stabi-lized polypropylene, a material which matches the polycar-bonate bottles in mechanical, thermal and chemical resis-tance to fluids. A large opening in the bottle simplifies fillingand emptying without spillage. The shape of the bottle issuch that it can be held securely even when wet to unscrewthe enclosure.


Catalog No.

A-4615-1A-4615-2A-4615-3A-4615-4A-4615-5A-4615-6

A-4615-7

Capacity

1 OZ.21/2 OZ.5 OZ.9 OZ.

1 PT.1 QT.

1/2 GAL.

A

2

27/8

35/8

5

C

21/16

31/16

3

41/4

51/4

85/8

93/8

Style DT

Also available in Remote Mounting

® Viton is a registered trademark of Dupont Dow Corp.

STEEL DISPENSERS dispense oil by gravity from a reser-voir without flow valves or shutoffs.

Designed to serve as a central reservoir in an oiling sys-tem, shutoff valve and additional sight feed valves are need-ed for the regulation of oil flow.

Top filler cap with strainer and filter are provided alongwith proper outlets, drains and inlets. Units are provided witha liquid level gage for visual check of the oil supply. Tanks five(5) gallons and larger have a sediment chamber.

Constructed of welded heavy gage steel, the top coverplate is suitable for mounting of components. (Special designmodifications are available on request).

SPECIFICATIONS:

• Temperature 225° F. Max.• Tanks are all welded rigid construction

suitable for component mounting on top cover• Tank Steel, Painted• Cover Steel, Painted• Level Gage Aluminum Alloy• Gaskets & Seals Buna-N and Vellumoid• Filler Cap Steel, Plated

HORIZONTAL ACRYLIC DISPENSERS dispense liquid bygravity, from a reservoir, with flow controlled by means of ashutoff valve.

These dispensers are designed to serve as a centralreservoir of an oiling system. The horizontal dispenser per-mits the use of large capacities without increasing height.The horizontal dispenser permits the use of large volumeswithout a significant change in head pressure. This allowsthe dispenser to have a more consistent flow from the outlet.

Reservoirs are rugged, transparent acrylic and permit acontinuous check of liquid supply. Self-closing filler caps areprovided.

SPECIFICATIONS:

• Pressure Atmospheric PressureGravity Feed Only, Reservoir isVented

• Temperature 160° F. Max. Acrylic225° F. Max. Pyrex

• Metering Full Flow with Toggle Shutoff • Reservoir Clear Acrylic or Pyrex• Seals Buna-N• Covers Aluminum Alloy• Valve Brass• Filler Cap Steel, Plated

Catalog Number

B-770-1B-770-2B-770-3B-774-2B-773-4B-999-2B-1194-1B-1195-1




B-995-1 —B-995-2 B-995-12B-995-3 —B-995-4 —

Capacity

1 QT.1/2 GAL.1 GAL.2 GAL.

F

53/4

91/4

141/4

271/4

E

9121/2

171/2

301/2

Capacity

1 GAL.2 GAL.3 GAL.5 GAL.

10 GAL.15 GAL.30 GAL.60 GAL.

C

101010

111/2

15152732

B

73/4

73/4

73/4

912122429

E

610141620242430

H

71/2

71/2

71/2

1012151520

F

43/4

83/4

123/4

141/4

181/4

213/4

213/4

281/4

G

61/4

61/4

61/4

79

123/4

123/4

173/4

I

21/64

21/64

21/64

17/32

17/32

17/32

17/32

17/32

J

———11111

Baffle

NONONOYESYESYESYESYES

Ho

rizo

nta

l Acr

ylic

an

d S

teel

Dis

pen

sers

Acrylic and Steel Dispensers

Style DHGStyle DT


********

12

*


P. O. BOX 1207, MANITOWOC, WI 54221-1207 (920) 682-6173 FAX (920) 682-7699Internet http://www.oilrite.com e-mail [email protected] 13

Air O

perated

Disp

ensers

Air Operated DispensersSTEEL AIR OPERATED DISPENSERS dispense oil by airpressure from a reservoir to elevated, distant, and inacces-sible points.

Designed to serve as a central reservoir of an oiling sys-tem, additional sight feed valves are needed for the regula-tion of oil flow.

Air pressure is applied through an adjustable pressureregulator on the unit. This will reduce the pressure within thereservoir to a valve suitable for dispensing: higher pressurefor heavy oils and long pipe runs, lower pressure for light oilsand shorter pipe runs.

To fill, simply turn off the air supply, bleed the reservoirand replenish liquid through the large filler cap on top of theunit.

These units feature a liquid filter readily accessible fromthe outside of the tank. The reservoir is made of weldedheavy gage steel and will withstand higher temperatures thanthe acrylic reservoir.

SPECIFICATIONS:

• Pressure 30 P.S.I. Max.• Temperature 225° F. Max.• Air Flow 5 C.F.M. at 20 P.S.I.• Liquid Flow 3 G.P.H. at 10 P.S.I.• Components Externally Mounted• Reservoir Steel, Painted• Seals Buna-N

ACRYLIC AIR OPERATED DISPENSERS dispense liq-uid,by air pressure, from a reservoir to elevated, distant andinaccessible points.


Air pressure is applied through an adjustable pressureregulator on the unit. This will reduce the pressure within thereservoir to a valve suitable for dispensing. Use higher pres-sure for heavy liquids and long pipe runs, and lower pressurefor light liquids and shorter pipe runs.

To fill the dispenser, simply turn off the air supply, bleedthe reservoir and replenish liquid through the large filler capon top of the unit.

These units feature a liquid filter within the reservoir. Thereservoir is made of crystal clear acrylic and provides a largefiller cap.

SPECIFICATIONS:

• Pressure 30 P.S.I. Max.• Temperature 160° F. Max.• Air Flow 5 C.F.M. at 20 P.S.I.• Liquid Flow 3 G.P.H. at 10 P.S.I.• Components Externally Mounted• Reservoir Clear Acrylic• Seals Buna-N • Covers Aluminum Alloy


Catalog Number

B-1318-1B-1318-2B-1318-3B-1318-4

Capacity

1 QT.1/2 GAL.1 GAL.2 GAL.

C

83/4

121/4

171/4

301/4


Catalog Number

B-1266-1B-1266-2

Capacity

21/2 GAL.5 GAL.

C

121/2

201/2

Style DHP

Style DHP

*

**** Special - Please Consult Factory



Sp

are

Par

ts

Lubricator

Drop Feed OilerSingle FeedDrop Feed OilerMultiple Feed

Catalog NumberTop Sight Btm. Sight

Sight Seal Seal

A-2693-2 A-4603-2 A-2698-2

A-2693-1 A-4603-1 A-2698-1

Catalog Number

A-2696-2A-2696-10

Used On

1 OZ. to 9 OZ.

1 PT. to 1/2 GAL.

O.D.

11/2

25/8

I.D.

11/8

23/32

PageRef.

4 & 5

6 & 7

Wall

3/32

3/32

Catalog Number

B-2017-1B-2017-2B-2017-3B-2017-4B-2017-5B-2017-6B-2017-9

Capacity

1 OZ.

21/2 OZ.5 OZ.9 OZ.1 PT.1QT.

1/2 GAL.

A

2

27/8

35/8

5

C

21/8

31/8

31/16

45/16

53/8

83/4

95/8

D

3/8

5/8

1

Catalog Number

A-3515-1A-3515-2A-3277-1A-3277-2B-1654-1B-1654-2

B-2432-1

Capacity

1 OZ.

21/2 OZ.5 OZ.9 OZ.1 PT.1QT.

1/2 GAL.

A

2

27/8

35/8

5

C

113/16

213/16

23/4

4

43/4

81/8

9

Catalog Number

A-4612-1A-4612-2

Used On

1 OZ. to 9 OZ.1 PT. to 1/2 GAL.

Catalog Number

B-1677-2B-2221-6

Used On


Catalog Number

B-1683-50B-1683-51B-1683-52B-1683-53B-1683-54B-1683-55

B-1683-56

Capacity

1 OZ.

21/2 OZ.5 OZ.9 OZ.1 PT.1QT.

1/2 GAL.

A

2

27/8

35/8

5

C

113/16

213/16

23/4

4

43/4

81/8

9

Spare Parts

Wall

Enclosure Gaskets for Polycarbonate Reservoirs Buna-N

O.D.

I.D.

Polycarbonate Reservoirs

No Hole With Center Hole With Hinge Lid

Sights and Sight Seals

No Hole With Center Hole With Retainer Strap

Polypropylene Enclosure Caps

Catalog Number

B-1586-1B-2189-1

Used On




Sp

are Parts C

on

t.

Seals

Reservoirs Acrylic

Catalog Number

B-2508-101B-2508-102B-2508-103

B

1/8

3/16

A

11/2

2

21/2

331/2

41/4

51/2

Catalog Number

A-2692-21A-2692-25A-2692-28A-2692-30A-2692-33A-2692-34

A-2692-36A-2692-37A-2692-38

Capacity

1 OZ.21/2 OZ.5 OZ.9 OZ.1 PT.1 QT.

1/2 GAL.

1 GAL.2 GAL.

C

13/8

17/8

23/8

345

7

1225

Spare Parts cont.

B

1/8

5/32

3/16

13/64

7/32

1/4

A

11/2

2

21/2

3

31/2

41/4

51/2

Catalog Number

A-2691-4A-2691-6A-2691-7A-2691-8A-2691-9

A-2691-10

A-2691-11

Capacity

1 OZ.21/2 OZ.5 OZ.9 OZ.1 PT.1 QT.

1/2 GAL.

C

13/8

17/8

23/8

345

7

Reservoirs Pyrex

I.D.

11/8

15/8

17/8

217/32

31/32

35/8

47/8

O.D.

11/2

21/32

217/32

31/32

317/32

419/64

535/64

Catalog No.

A-2696-2A-2696-4A-2696-5A-2696-6A-2696-7A-2696-8A-2696-9

Capacity

1 OZ.21/2 OZ.5 OZ.9 OZ.1 PT.1 QT.

1/2 , 1 & 2 GAL.

Wall

3/32

Volts & Frequency

120 volts, 60 Hz.240 volts, 60 Hz.480 volts, 60 Hz.

Spare Coil Only

Buna-N Enclosure Gaskets for Acrylicand Pyrex Reservoirs.

SOLENOID The following information is supplied as sup-plementary data on Oil-Rite solenoid operators. The nor-mally closed solenoid operator can be supplied with thesame voltage and frequencies as required for systemdrive motors, allowing it to be wired parallel to the motorproviding automatic operation. Solenoid operators arewarranted against failure and replacement coils areoffered free on any coil that fails in the field for a nominalshipping charge.

SPECIFICATIONS:• Pressure 1/16 orifice 125 P.S.I.

1/4 orifice 5 to 8 P.S.I.• Media Temperature -45° F. to + 185° F.• Nomial Power 7 Watts• Coil Construction Water Resistant

Class “B” + 130° C.• Coil Housing Steel• Center Core Stainless Steel• Plunger Stainless Steel• Seat Buna-N• Seals Buna-N

(Optional Seal MaterialEthylene Propylene, Viton® A)

(For complete operating characteristics consult factory.)

Acrylic and Pyrex Reservoirs

A

B

C

The new solenoid operator is interchangeable with the following Oil-Rite styles currently in use:DEY DEH DEF SLVADE DEJ DEC SLV

Model Number

Solenoid Operator

B-1725-1

When Ordering Specify:• Model Number• Voltage and Frequency• Seal Material

Filter

100 Mesh

CatalogNumber

A-4655-1

Capacity


1/2 GAL.1 GAL.

CatalogNumber

A-4656-1A-4656-2A-4656-3A-4656-4A-4656-5A-4656-6

C

215/32

37/32

47/32

57/16

77/16

127/16


Wall

O.D.

I.D.

Acrylic and Pyrex Reservoir Filters

Polycarbonate Reservoir Filter100Mesh

100Mesh

1/2 N.P.T.Female Thread

3/4 - 32Thread

Other Volts and Frequency-Consult Factory

® Viton is a registered trademark of Dupont Dow Corp.


Inst

alla

tio

n In

stru

ctio

n

INSTALLATION

1. Oil level is usually marked on the baseof oiler. Mount oiler by using side orbottom outlet at the exact and mostdesirable level.

2. Correct oil level is lowest level atwhich bearing operates perfectly.

3. Lubricator should be level in all direc-tions to function at its best.

4. Keep connections short, rigid, andclose to bearing to avoid vibration.

5. Fill bearing well by filling oiler.Repeated filling may be necessary.

6. The anti-friction bearings should befitted with breather tubes piped to theoutside or to air intake of oiler.

7. On oilers with top filler cap, be surecap is always screwed down tight.Removing filler cap shuts off oilsupply. Loose filler cap causesleakage of oil from reservoirthrough vent hole, rendering oilerineffective.

PRINCIPLE

Constant level lubricators automaticallymaintain the oil in a bearing reservoir at aconstant level. Operation is based on theliquid seal principle. When the oil in thebearing recedes because of oil consump-tion, the liquid seal on the inside of thelubricator is temporarily broken. Thisallows air from the air intake to enter thelubricator reservoir, releasing oil until aseal and proper level are again estab-lished.

APPLICATIONS

Constant level lubricators are used onsleeve bearing, anti-friction bearings,gear boxes, pump housing, etc. Otheruses include moistening pads and anyother application demanding the mainte-nance of a constant liquid level.

OIL LEVEL

Oil-Rite has available constant level lubricators with fixed or with adjustable oillevel. Original equipment manufacturersusually prefer lubricator with fixed oil levelto make an installation tamperproof.

OIL RESERVOIR

Oil-Rite offers constant level lubricatorswith acrylic, glass, or high temperatureplastic reservoirs to suit specific applica-tions. The reservoirs are transparent topermit a visual check of the oil supply atall times. Since the oil in the reservoirassumes the same color as that in thebearing housing, a visual check of thecondition of the oil is also afforded.

This installation is especially suitable for bear-ings having excessive back pressure or vacu-um. A constant level is maintained in spite ofair pressure or vacuum in bearing, as equaliz-ing tube assures static balance of pressurebetween bearing and oiler.

AIR INLET

The air inlet on Oil-Rite’s constant levellubricators is provided with a pipe threadto accommodate an air filter for the pre-vention of dust and dirt getting into the oil.

For dusty and dirty surroundings, suchas those found in cement mills, textileplants, paper mills, coal handling facili-ties, etc. it is recommended that the airinlet of the lubricator be piped into the topof the bearing housing. Such a closed cir-cuit offers full protection.

Pressure differential between the airintake of the lubricator and the bearinghousing, such as is experienced onventilating fans and blowers, anti-fric-tion bearings,etc., necessitates thatthe air inlet on the lubricator be pipedinto the top of the bearing housing toequalize pressure.

SURGE LEVEL

In certain cases, such as in gear boxes, aconsiderable quantity of oil is carried bythe gears to the upper portion of the gearhousing during operation. After shutdown,the oil surges back to the lubricator andraises the oil level. Constant level lubrica-tor should therefore be equipped with asufficient surge level to prevent oil fromoverflowing through the air intake.

Typical installation for ring-oiled bearings. Oillevel should be slightly above inside diameterof ring. With the correct oil level the ring carriesoil to shaft smoothly without splashing andchattering.

Constant Level Lubricator Installation Instructions

section 1000 index - major eng section 1000.pdf · section 1000 index dispense liquid, by gravity,...

Documents