seamless rotary guidance system: bishop-wisecarver 1-trak part ii
DESCRIPTION
Part 2 of III: An innovative technology from Bishop-Wisecarver has effectively changed the face of curvilinear track design possibilities. Part of the highly successful HepcoMotion PRT2 family of products, the new and patent pending 1-Trak product allows track systems to be manufactured in almost any conceivable 2D shape and from one single piece of material.TRANSCRIPT
© 2013 | All Rights Reserved | www.bwc.com
Motion Without Limits ®
Introducing PRT2 1-Trak: Part II of III
A Seamless Ring and Track Guided Motion System
© 2013 | All Rights Reserved | www.bwc.com
Motion Without Limits ®
OUTLINE OF OVERVIEW — PART II OF III
Overview
Driving By Gears
Gear Options
PRT2 Tracks Via 1-Trak Route
Contact Information
© 2013 | All Rights Reserved | www.bwc.com
Motion Without Limits ®
NEW! PRT2 1-TRAK
1-Trak extends the capability of PRT2
Patent pending design with three key innovations:Create almost any 2D shape of track in one piece(within the maximum size limits and minimum bend radii)
Three-bearing geometry allows a carriage to run around any 2D shape of track
Available with or without gear drive
© 2013 | All Rights Reserved | www.bwc.com
Motion Without Limits ®
1-TRAK APPROACH TO DRIVING BY GEARS
© 2013 | All Rights Reserved | www.bwc.com
Motion Without Limits ®
1-TRAK APPROACH TO DRIVING BY GEARS
The pinion in a fixed position on the carriage, and the pitch line of the gear follows the 1-Trak path
© 2013 | All Rights Reserved | www.bwc.com
Motion Without Limits ®
DRIVING BY GEARS EXAMPLE
© 2013 | All Rights Reserved | www.bwc.com
Motion Without Limits ®
GEAR DRIVEN 1-TRAK SYSTEMS
Gear teeth are surface hardened high tensile steel: same as the slide vees
Driving forces and durability are excellent
Making these gears is difficult: pitch line follows a complex path, and the shape of the teeth changes with path curvature
Utilize dedicated CAM system to generate gear profiles for any track system and any pinion position
© 2013 | All Rights Reserved | www.bwc.com
Motion Without Limits ®
GEAR DRIVEN 1-TRAK SYSTEMS
When the driving pinion is located off-center, the path of the gear becomes more complex and asymmetrical
There will be no problem for the new CAM system
© 2013 | All Rights Reserved | www.bwc.com
Motion Without Limits ®
1-TRAK GEAR OPTION
The production method works best with gears of MOD3 or larger with the following tooth widths:
MOD3 up to 12mm wide
MOD5 up to 20mm wide
MOD8 up to 32mm wide
MOD10 up to 40mm wide
The most suitable Hepco pinions are in the HDS2 catalogue
We also now have a MOD8 stock pinion for use with HDRE1656G8: HP8X17
© 2013 | All Rights Reserved | www.bwc.com
Motion Without Limits ®
1-TRAK GEAR OPTION
Detailed gear drive calculations will need to be referred to an Applications Engineer
For provisional sizing:Use HDS2 figures pro-rated for width, and then add 50% due to higher specification of gear teeth
© 2013 | All Rights Reserved | www.bwc.com
Motion Without Limits ®
1-TRAK GEAR OPTION
The shape of the gears on the track will be defined if the pinion size (MOD and number of teeth) is defined, along with the location of its center on the carriage Ensure that there is enough space to accommodate the pinion — remember that in designs where the pinion is away from the carriage center, the gear pitch line will deviate a long way from the track vees
© 2013 | All Rights Reserved | www.bwc.com
Motion Without Limits ®
1-TRAK GEAR OPTION
Specify either a gearbox or a drive flange assembly(for example from HDS2 catalog) Lubrication is essential
In some cases it will be possible to use HDS2 automatic rack lubrication method, directly onto the pinion
© 2013 | All Rights Reserved | www.bwc.com
Motion Without Limits ®
PRT2 TRACKS VIA 1-TRAK ROUTE
It is possible to have the benefits of 1-Trak construction, e.g. one-piece, integral base plate and structural strength, but using the standard PRT2 track shapes and FCC or BCP carriages(which are stronger than three-bearing carriages)
Just specify the track system using the standard PRT2 method, state “made via 1-Trak route”, and then provide a sketch to show relevant base plate and customization details
© 2013 | All Rights Reserved | www.bwc.com
Motion Without Limits ®
PRT2 TRACKS VIA 1-TRAK ROUTE
The 1-Trak approach may also be used on more complex systems DTS could be made via this construction DTS2 also possible
© 2013 | All Rights Reserved | www.bwc.com
Motion Without Limits ®
CONTINUED…
Be sure to view part III of III in the 1-Trak overview series for more information on:
How To Specify 1-Trak
Available on the Bishop-Wisecarver’s SlideShare: (www.slideshare.net/bishopwisecarver)
© 2013 | All Rights Reserved | www.bwc.com
Motion Without Limits ®
THANK YOU
Have questions? Please contact…An Applications Engineer at (888) 580.8272
Or email [email protected]
Learn more on our website at www.bwc.com