screen protector installation...

Your computer is designed to provide you with years of service. Using a screen protector will help ensure that the screen remains as clear as possible. When installed, the screen protector becomes a durable, replaceable writing surface that protects the display screen from abrasion.

SCREEN PROTECTOR INSTALLATION NOTE: The system shown in this manual is for illustration purposes; your system may look different from that shown.

Preparation/Removal

To remove and/or prepare a new screen protector on your display:

1. If a screen protector is already installed on the display, remove it before installing the new screen protector.

DURING NORMAL USE OF YOUR SYSTEM, SMALL PARTICLES FROM THE ENVIRONMENT CAN BECOME EMBEDDED IN THE PEN TIP AND SCRATCH THE SCREEN. TO PREVENT SCRATCHING THE SCREEN, ENSURE THAT A SCREEN PROTECTOR IS INSTALLED BEFORE USING YOUR COMPUTER. THE WARRANTY DOES NOT COVER A SCRATCHED SCREEN.

I N S T R U C T I O N S

Screen Protector Installation Instructions

F u j i t s u A m e r i c a , I n c .

screen protector - Claw.fm Wednesday, June 29, 2011 8:20 AM

2

2. To ensure good adhesion, clean the display screen with a soft cloth such as the micro-fiber cloth that came with your system or a soft cotton cloth.

Installation

The screen protector has removable protective sheets on the front and the back. The front of the protective sheet has a red pull tab extending from it, while the back protective sheet does not. The back of the screen protector has a strip of adhesive running around the perimeter with which it is held onto the display screen surface.

1. IMPORTANT: This screen protector has been designed for use with more than one model of Fujitsu computers. On some models, the screen protector will fit close to the window bezel on all four sides. On other models, however, there will be a gap of 3.5 mm to 4 mm between the screen protector and the bezel.

To ensure that you properly position the screen protector, lay it atop the display before you remove the protective backing. Position it in the center of the display symmetri-cally, with equal left/right gaps and top/bottom gaps. When positioning the screen protector in the following steps, be sure that you maintain the equal gaps.

2. First remove the protective sheet from the back adhesive side of the screen protector, as shown in Figure 1. A notch in one corner of the screen protector allows you to slide your fingernail or a credit card under the back protective sheet for easy removal. Do not use a metal implement; it could scratch the screen or the screen protector. This is the side that will be applied to the screen.


3

Figure 1. Removing the Protective Sheet

3. Apply the screen protector to the display screen surface starting in the upper right corner. When doing so, orient the screen protector with the adhesive side of the screen protector facing the display screen and the notched corner of the screen protector oriented as shown in Figure 2

4. Apply pressure to the screen protector with your finger using continuous pressure along the edges. Allow 48 hours for the adhesive to set completely. To ensure a good seal between the screen protector and the display, do not lift the screen protector from the display once it has been applied.

IT IS VERY IMPORTANT THAT THE LOWER LEFT EDGE OF THE SCREEN PROTECTOR IS NOT TOUCHING THE DISPLAY BEZEL. DOING SO CAN APPLY UNDUE PRESSURE TO THE [START] ICON WHEN THE COVER IS CLOSED, RESULTING IN ERRATIC OPERATION.

Adhesivebacking

ScreenProtector

RedPull Tab


4

Figure 2. Installing the screen protector

5. Remove the protective plastic film from the face of the screen protector by lifting it at the red tab, as shown in Figure 3. Failure to do so will result in a “cloudy” appearance to the screen.


5

Figure 3. Removing the protective film

6. Clean any residue left behind from the exposed surface of the screen protector by wiping it gently with a soft cloth such as a micro-fiber cloth or a soft cotton cloth.

Red Pull Tab


6


7


8

1250 E. Arques Avenue, Sunnyvale, California 94085

For more information, visit our Web site at: http://us.fujitsu.com/computers

For technical support call:1-800-8FUJITSU (1-800-838-5487)

Fujitsu and the Fujitsu logo are registered trademarks of Fujitsu, Ltd. All other trademarks mentioned herein are the property of their respective owners. Fujitsu America, Inc. has made every effort to ensure the accuracy and completeness of this document. As ongoing development efforts continually improve the capabilities of our products, we cannot guarantee the accuracy of the contents of this document. We disclaim liability for errors, omissions, or future changes.

© 2011 Fujitsu America, Incorporated. All rights reserved.

B6FY-0801-01EN-00


screen protector installation...

Documents